Message ID | 1329124271-29464-2-git-send-email-ming.m.lin@intel.com |
---|---|
State | Not Applicable |
Delegated to: | David Miller |
Headers | show |
On Monday, February 13, 2012, Lin Ming wrote: > From: Zhang Rui <rui.zhang@intel.com> > > If a device has _PR3._ON, it means the device supports D3_HOT. > If a device has _PR3._OFF, it means the device supports D3_COLD. > Add the ability to validate and enter D3_COLD state in ACPI. > > Signed-off-by: Zhang Rui <rui.zhang@intel.com> This is supposed to be ACPI 5.0 support, right? So can anyone please tell me what part of the ACPI 5.0 spec is the basis of this patch, because I can't see that immediately? The only places where D3Cold is _mentioned_ are Section 7.2.12 (_PRE, which appears to be new in 5.0), Section 7.2.20 (_S0W), Section 7.2.21 (_S1W), Section 7.2.22 (_S2W), Section 7.2.23 (_S3W) and Section 7.2.24 (_S4W). None of them mentions those _PR3._ON and _PR3._OFF things above. Moreover, my understanding of the spec is that D3Cold means all of the power resources returned by _PR3 are "off" (whereas some of them will be "on" in D3hot). > --- > drivers/acpi/power.c | 4 ++-- > drivers/acpi/scan.c | 10 +++++++++- > 2 files changed, 11 insertions(+), 3 deletions(-) > > diff --git a/drivers/acpi/power.c b/drivers/acpi/power.c > index 9ac2a9f..0d681fb 100644 > --- a/drivers/acpi/power.c > +++ b/drivers/acpi/power.c > @@ -500,14 +500,14 @@ int acpi_power_transition(struct acpi_device *device, int state) > { > int result; > > - if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3)) > + if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3_COLD)) > return -EINVAL; > > if (device->power.state == state) > return 0; > > if ((device->power.state < ACPI_STATE_D0) > - || (device->power.state > ACPI_STATE_D3)) > + || (device->power.state > ACPI_STATE_D3_COLD)) > return -ENODEV; > > /* TBD: Resources must be ordered. */ > diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c > index 8ab80ba..a9d4391 100644 > --- a/drivers/acpi/scan.c > +++ b/drivers/acpi/scan.c > @@ -881,8 +881,16 @@ static int acpi_bus_get_power_flags(struct acpi_device *device) > > device->power.flags.power_resources = 1; > ps->flags.valid = 1; > - for (j = 0; j < ps->resources.count; j++) > + for (j = 0; j < ps->resources.count; j++) { > acpi_bus_add_power_resource(ps->resources.handles[j]); > + /* Check for D3_COLD support. _PR3._OFF equals D3_COLD ? */ > + if (i == ACPI_STATE_D3) { > + if (j == 0) > + device->power.states[ACPI_STATE_D3_COLD].flags.valid = 1; > + status = acpi_get_handle(ps->resources.handles[j], "_OFF", &handle); > + device->power.states[ACPI_STATE_D3_COLD].flags.valid &= ACPI_SUCCESS(status); > + } > + } Sorry, but this doesn't make sense to me. Power resources always have the _OFF method, right? > } > > /* Evaluate "_PSx" to see if we can do explicit sets */ > Rafael -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi, Rafael, On 一, 2012-02-13 at 21:25 +0100, Rafael J. Wysocki wrote: > On Monday, February 13, 2012, Lin Ming wrote: > > From: Zhang Rui <rui.zhang@intel.com> > > > > If a device has _PR3._ON, it means the device supports D3_HOT. > > If a device has _PR3._OFF, it means the device supports D3_COLD. > > Add the ability to validate and enter D3_COLD state in ACPI. > > > > Signed-off-by: Zhang Rui <rui.zhang@intel.com> > > This is supposed to be ACPI 5.0 support, right? > No, D3_HOT is introduced in ACPI spec 4.0. According to the spec, _PR3 is used for devices that support both D3(D3_COLD) and D3HOT. The confusion here is that Linux D3 equals ACPICA D3HOT and Linux D3_COLD equals ACPICA D3. For example, when enter Linux ACPI D3, the reference count of ACPI Power Resources in _PR3 is increased by one. > So can anyone please tell me what part of the ACPI 5.0 spec is the > basis of this patch, because I can't see that immediately? > > The only places where D3Cold is _mentioned_ are Section 7.2.12 (_PRE, which > appears to be new in 5.0), Section 7.2.20 (_S0W), Section 7.2.21 (_S1W), > Section 7.2.22 (_S2W), Section 7.2.23 (_S3W) and Section 7.2.24 (_S4W). > None of them mentions those _PR3._ON and _PR3._OFF things above. > > Moreover, my understanding of the spec is that D3Cold means all of the > power resources returned by _PR3 are "off" (whereas some of them will be > "on" in D3hot). > Agreed. > > --- > > drivers/acpi/power.c | 4 ++-- > > drivers/acpi/scan.c | 10 +++++++++- > > 2 files changed, 11 insertions(+), 3 deletions(-) > > > > diff --git a/drivers/acpi/power.c b/drivers/acpi/power.c > > index 9ac2a9f..0d681fb 100644 > > --- a/drivers/acpi/power.c > > +++ b/drivers/acpi/power.c > > @@ -500,14 +500,14 @@ int acpi_power_transition(struct acpi_device *device, int state) > > { > > int result; > > > > - if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3)) > > + if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3_COLD)) > > return -EINVAL; > > > > if (device->power.state == state) > > return 0; > > > > if ((device->power.state < ACPI_STATE_D0) > > - || (device->power.state > ACPI_STATE_D3)) > > + || (device->power.state > ACPI_STATE_D3_COLD)) > > return -ENODEV; > > > > /* TBD: Resources must be ordered. */ > > diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c > > index 8ab80ba..a9d4391 100644 > > --- a/drivers/acpi/scan.c > > +++ b/drivers/acpi/scan.c > > @@ -881,8 +881,16 @@ static int acpi_bus_get_power_flags(struct acpi_device *device) > > > > device->power.flags.power_resources = 1; > > ps->flags.valid = 1; > > - for (j = 0; j < ps->resources.count; j++) > > + for (j = 0; j < ps->resources.count; j++) { > > acpi_bus_add_power_resource(ps->resources.handles[j]); > > + /* Check for D3_COLD support. _PR3._OFF equals D3_COLD ? */ > > + if (i == ACPI_STATE_D3) { > > + if (j == 0) > > + device->power.states[ACPI_STATE_D3_COLD].flags.valid = 1; > > + status = acpi_get_handle(ps->resources.handles[j], "_OFF", &handle); > > + device->power.states[ACPI_STATE_D3_COLD].flags.valid &= ACPI_SUCCESS(status); > > + } > > + } > > Sorry, but this doesn't make sense to me. Power resources always have > the _OFF method, right? > I'm not sure. I thought I had seen ACPI Power Resources without _OFF control method somewhere in bugzilla, but I can not find it out now. Hmm, how about set D3_COLD support if _PR3 exists, but leave a warning message if _OFF doesn't exist, for now? thanks, rui -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tuesday, February 14, 2012, Zhang Rui wrote: > Hi, Rafael, > > On 一, 2012-02-13 at 21:25 +0100, Rafael J. Wysocki wrote: > > On Monday, February 13, 2012, Lin Ming wrote: > > > From: Zhang Rui <rui.zhang@intel.com> > > > > > > If a device has _PR3._ON, it means the device supports D3_HOT. > > > If a device has _PR3._OFF, it means the device supports D3_COLD. > > > Add the ability to validate and enter D3_COLD state in ACPI. > > > > > > Signed-off-by: Zhang Rui <rui.zhang@intel.com> > > > > This is supposed to be ACPI 5.0 support, right? > > > No, D3_HOT is introduced in ACPI spec 4.0. > According to the spec, _PR3 is used for devices that support both > D3(D3_COLD) and D3HOT. Yes, it does. > The confusion here is that Linux D3 equals ACPICA D3HOT and Linux > D3_COLD equals ACPICA D3. > For example, when enter Linux ACPI D3, the reference count of ACPI Power > Resources in _PR3 is increased by one. That's correct. > > So can anyone please tell me what part of the ACPI 5.0 spec is the > > basis of this patch, because I can't see that immediately? > > > > The only places where D3Cold is _mentioned_ are Section 7.2.12 (_PRE, which > > appears to be new in 5.0), Section 7.2.20 (_S0W), Section 7.2.21 (_S1W), > > Section 7.2.22 (_S2W), Section 7.2.23 (_S3W) and Section 7.2.24 (_S4W). > > None of them mentions those _PR3._ON and _PR3._OFF things above. > > > > Moreover, my understanding of the spec is that D3Cold means all of the > > power resources returned by _PR3 are "off" (whereas some of them will be > > "on" in D3hot). > > > Agreed. > > > > --- > > > drivers/acpi/power.c | 4 ++-- > > > drivers/acpi/scan.c | 10 +++++++++- > > > 2 files changed, 11 insertions(+), 3 deletions(-) > > > > > > diff --git a/drivers/acpi/power.c b/drivers/acpi/power.c > > > index 9ac2a9f..0d681fb 100644 > > > --- a/drivers/acpi/power.c > > > +++ b/drivers/acpi/power.c > > > @@ -500,14 +500,14 @@ int acpi_power_transition(struct acpi_device *device, int state) > > > { > > > int result; > > > > > > - if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3)) > > > + if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3_COLD)) > > > return -EINVAL; > > > > > > if (device->power.state == state) > > > return 0; > > > > > > if ((device->power.state < ACPI_STATE_D0) > > > - || (device->power.state > ACPI_STATE_D3)) > > > + || (device->power.state > ACPI_STATE_D3_COLD)) > > > return -ENODEV; > > > > > > /* TBD: Resources must be ordered. */ > > > diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c > > > index 8ab80ba..a9d4391 100644 > > > --- a/drivers/acpi/scan.c > > > +++ b/drivers/acpi/scan.c > > > @@ -881,8 +881,16 @@ static int acpi_bus_get_power_flags(struct acpi_device *device) > > > > > > device->power.flags.power_resources = 1; > > > ps->flags.valid = 1; > > > - for (j = 0; j < ps->resources.count; j++) > > > + for (j = 0; j < ps->resources.count; j++) { > > > acpi_bus_add_power_resource(ps->resources.handles[j]); > > > + /* Check for D3_COLD support. _PR3._OFF equals D3_COLD ? */ > > > + if (i == ACPI_STATE_D3) { > > > + if (j == 0) > > > + device->power.states[ACPI_STATE_D3_COLD].flags.valid = 1; > > > + status = acpi_get_handle(ps->resources.handles[j], "_OFF", &handle); > > > + device->power.states[ACPI_STATE_D3_COLD].flags.valid &= ACPI_SUCCESS(status); > > > + } > > > + } > > > > Sorry, but this doesn't make sense to me. Power resources always have > > the _OFF method, right? > > > I'm not sure. That would be explicitly against the spec that says that power resources are *required* to have _ON, _OFF and _STA. > I thought I had seen ACPI Power Resources without _OFF > control method somewhere in bugzilla, but I can not find it out now. That, clearly, is a firmware bug. > Hmm, how about set D3_COLD support if _PR3 exists, but leave a warning > message if _OFF doesn't exist, for now? I don't think we need to set D3_COLD support at all. In fact, it is always supported (as I said, if all power resources used by a device are off, the device is in D3_COLD pretty much by definition). Thanks, Rafael -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 二, 2012-02-14 at 23:29 +0100, Rafael J. Wysocki wrote: > On Tuesday, February 14, 2012, Zhang Rui wrote: > > Hi, Rafael, > > > > On 一, 2012-02-13 at 21:25 +0100, Rafael J. Wysocki wrote: > > > On Monday, February 13, 2012, Lin Ming wrote: > > > > From: Zhang Rui <rui.zhang@intel.com> > > > > > > > > If a device has _PR3._ON, it means the device supports D3_HOT. > > > > If a device has _PR3._OFF, it means the device supports D3_COLD. > > > > Add the ability to validate and enter D3_COLD state in ACPI. > > > > > > > > Signed-off-by: Zhang Rui <rui.zhang@intel.com> > > > > > > This is supposed to be ACPI 5.0 support, right? > > > > > No, D3_HOT is introduced in ACPI spec 4.0. > > According to the spec, _PR3 is used for devices that support both > > D3(D3_COLD) and D3HOT. > > Yes, it does. > > > The confusion here is that Linux D3 equals ACPICA D3HOT and Linux > > D3_COLD equals ACPICA D3. > > For example, when enter Linux ACPI D3, the reference count of ACPI Power > > Resources in _PR3 is increased by one. > > That's correct. > > > > So can anyone please tell me what part of the ACPI 5.0 spec is the > > > basis of this patch, because I can't see that immediately? > > > > > > The only places where D3Cold is _mentioned_ are Section 7.2.12 (_PRE, which > > > appears to be new in 5.0), Section 7.2.20 (_S0W), Section 7.2.21 (_S1W), > > > Section 7.2.22 (_S2W), Section 7.2.23 (_S3W) and Section 7.2.24 (_S4W). > > > None of them mentions those _PR3._ON and _PR3._OFF things above. > > > > > > Moreover, my understanding of the spec is that D3Cold means all of the > > > power resources returned by _PR3 are "off" (whereas some of them will be > > > "on" in D3hot). > > > > > Agreed. > > > > > > --- > > > > drivers/acpi/power.c | 4 ++-- > > > > drivers/acpi/scan.c | 10 +++++++++- > > > > 2 files changed, 11 insertions(+), 3 deletions(-) > > > > > > > > diff --git a/drivers/acpi/power.c b/drivers/acpi/power.c > > > > index 9ac2a9f..0d681fb 100644 > > > > --- a/drivers/acpi/power.c > > > > +++ b/drivers/acpi/power.c > > > > @@ -500,14 +500,14 @@ int acpi_power_transition(struct acpi_device *device, int state) > > > > { > > > > int result; > > > > > > > > - if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3)) > > > > + if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3_COLD)) > > > > return -EINVAL; > > > > > > > > if (device->power.state == state) > > > > return 0; > > > > > > > > if ((device->power.state < ACPI_STATE_D0) > > > > - || (device->power.state > ACPI_STATE_D3)) > > > > + || (device->power.state > ACPI_STATE_D3_COLD)) > > > > return -ENODEV; > > > > > > > > /* TBD: Resources must be ordered. */ > > > > diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c > > > > index 8ab80ba..a9d4391 100644 > > > > --- a/drivers/acpi/scan.c > > > > +++ b/drivers/acpi/scan.c > > > > @@ -881,8 +881,16 @@ static int acpi_bus_get_power_flags(struct acpi_device *device) > > > > > > > > device->power.flags.power_resources = 1; > > > > ps->flags.valid = 1; > > > > - for (j = 0; j < ps->resources.count; j++) > > > > + for (j = 0; j < ps->resources.count; j++) { > > > > acpi_bus_add_power_resource(ps->resources.handles[j]); > > > > + /* Check for D3_COLD support. _PR3._OFF equals D3_COLD ? */ > > > > + if (i == ACPI_STATE_D3) { > > > > + if (j == 0) > > > > + device->power.states[ACPI_STATE_D3_COLD].flags.valid = 1; > > > > + status = acpi_get_handle(ps->resources.handles[j], "_OFF", &handle); > > > > + device->power.states[ACPI_STATE_D3_COLD].flags.valid &= ACPI_SUCCESS(status); > > > > + } > > > > + } > > > > > > Sorry, but this doesn't make sense to me. Power resources always have > > > the _OFF method, right? > > > > > I'm not sure. > > That would be explicitly against the spec that says that power resources > are *required* to have _ON, _OFF and _STA. > > > I thought I had seen ACPI Power Resources without _OFF > > control method somewhere in bugzilla, but I can not find it out now. > > That, clearly, is a firmware bug. > Okay, agreed. so how about this? _PR3 equals D3_HOT support. > > Hmm, how about set D3_COLD support if _PR3 exists, but leave a warning > > message if _OFF doesn't exist, for now? > > I don't think we need to set D3_COLD support at all. In fact, it is always > supported (as I said, if all power resources used by a device are off, the > device is in D3_COLD pretty much by definition). > Yeah, but it seems that Linux uses ACPI_D3 for both ACPICA D3_HOT and D3 (off). I'm generating a patch to remove ACPI_D3_COLD and introduce D3_HOT support in Linux kernel. thanks, rui -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thursday, February 16, 2012, Zhang Rui wrote: > On 二, 2012-02-14 at 23:29 +0100, Rafael J. Wysocki wrote: > > On Tuesday, February 14, 2012, Zhang Rui wrote: > > > Hi, Rafael, > > > > > > On 一, 2012-02-13 at 21:25 +0100, Rafael J. Wysocki wrote: > > > > On Monday, February 13, 2012, Lin Ming wrote: > > > > > From: Zhang Rui <rui.zhang@intel.com> > > > > > > > > > > If a device has _PR3._ON, it means the device supports D3_HOT. > > > > > If a device has _PR3._OFF, it means the device supports D3_COLD. > > > > > Add the ability to validate and enter D3_COLD state in ACPI. > > > > > > > > > > Signed-off-by: Zhang Rui <rui.zhang@intel.com> > > > > > > > > This is supposed to be ACPI 5.0 support, right? > > > > > > > No, D3_HOT is introduced in ACPI spec 4.0. > > > According to the spec, _PR3 is used for devices that support both > > > D3(D3_COLD) and D3HOT. > > > > Yes, it does. > > > > > The confusion here is that Linux D3 equals ACPICA D3HOT and Linux > > > D3_COLD equals ACPICA D3. > > > For example, when enter Linux ACPI D3, the reference count of ACPI Power > > > Resources in _PR3 is increased by one. > > > > That's correct. > > > > > > So can anyone please tell me what part of the ACPI 5.0 spec is the > > > > basis of this patch, because I can't see that immediately? > > > > > > > > The only places where D3Cold is _mentioned_ are Section 7.2.12 (_PRE, which > > > > appears to be new in 5.0), Section 7.2.20 (_S0W), Section 7.2.21 (_S1W), > > > > Section 7.2.22 (_S2W), Section 7.2.23 (_S3W) and Section 7.2.24 (_S4W). > > > > None of them mentions those _PR3._ON and _PR3._OFF things above. > > > > > > > > Moreover, my understanding of the spec is that D3Cold means all of the > > > > power resources returned by _PR3 are "off" (whereas some of them will be > > > > "on" in D3hot). > > > > > > > Agreed. > > > > > > > > --- > > > > > drivers/acpi/power.c | 4 ++-- > > > > > drivers/acpi/scan.c | 10 +++++++++- > > > > > 2 files changed, 11 insertions(+), 3 deletions(-) > > > > > > > > > > diff --git a/drivers/acpi/power.c b/drivers/acpi/power.c > > > > > index 9ac2a9f..0d681fb 100644 > > > > > --- a/drivers/acpi/power.c > > > > > +++ b/drivers/acpi/power.c > > > > > @@ -500,14 +500,14 @@ int acpi_power_transition(struct acpi_device *device, int state) > > > > > { > > > > > int result; > > > > > > > > > > - if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3)) > > > > > + if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3_COLD)) > > > > > return -EINVAL; > > > > > > > > > > if (device->power.state == state) > > > > > return 0; > > > > > > > > > > if ((device->power.state < ACPI_STATE_D0) > > > > > - || (device->power.state > ACPI_STATE_D3)) > > > > > + || (device->power.state > ACPI_STATE_D3_COLD)) > > > > > return -ENODEV; > > > > > > > > > > /* TBD: Resources must be ordered. */ > > > > > diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c > > > > > index 8ab80ba..a9d4391 100644 > > > > > --- a/drivers/acpi/scan.c > > > > > +++ b/drivers/acpi/scan.c > > > > > @@ -881,8 +881,16 @@ static int acpi_bus_get_power_flags(struct acpi_device *device) > > > > > > > > > > device->power.flags.power_resources = 1; > > > > > ps->flags.valid = 1; > > > > > - for (j = 0; j < ps->resources.count; j++) > > > > > + for (j = 0; j < ps->resources.count; j++) { > > > > > acpi_bus_add_power_resource(ps->resources.handles[j]); > > > > > + /* Check for D3_COLD support. _PR3._OFF equals D3_COLD ? */ > > > > > + if (i == ACPI_STATE_D3) { > > > > > + if (j == 0) > > > > > + device->power.states[ACPI_STATE_D3_COLD].flags.valid = 1; > > > > > + status = acpi_get_handle(ps->resources.handles[j], "_OFF", &handle); > > > > > + device->power.states[ACPI_STATE_D3_COLD].flags.valid &= ACPI_SUCCESS(status); > > > > > + } > > > > > + } > > > > > > > > Sorry, but this doesn't make sense to me. Power resources always have > > > > the _OFF method, right? > > > > > > > I'm not sure. > > > > That would be explicitly against the spec that says that power resources > > are *required* to have _ON, _OFF and _STA. > > > > > I thought I had seen ACPI Power Resources without _OFF > > > control method somewhere in bugzilla, but I can not find it out now. > > > > That, clearly, is a firmware bug. > > > Okay, agreed. > so how about this? _PR3 equals D3_HOT support. Yes, I can agree with that. :-) > > > Hmm, how about set D3_COLD support if _PR3 exists, but leave a warning > > > message if _OFF doesn't exist, for now? > > > > I don't think we need to set D3_COLD support at all. In fact, it is always > > supported (as I said, if all power resources used by a device are off, the > > device is in D3_COLD pretty much by definition). > > > Yeah, but it seems that Linux uses ACPI_D3 for both ACPICA D3_HOT and D3 > (off). I'm generating a patch to remove ACPI_D3_COLD and introduce > D3_HOT support in Linux kernel. That's a good idea in my opinion. Thanks, Rafael -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 五, 2012-02-17 at 23:23 +0100, Rafael J. Wysocki wrote: > > Okay, agreed. > > so how about this? _PR3 equals D3_HOT support. > > Yes, I can agree with that. :-) > > > > > Hmm, how about set D3_COLD support if _PR3 exists, but leave a warning > > > > message if _OFF doesn't exist, for now? > > > > > > I don't think we need to set D3_COLD support at all. In fact, it is always > > > supported (as I said, if all power resources used by a device are off, the > > > device is in D3_COLD pretty much by definition). > > > > > Yeah, but it seems that Linux uses ACPI_D3 for both ACPICA D3_HOT and D3 > > (off). I'm generating a patch to remove ACPI_D3_COLD and introduce > > D3_HOT support in Linux kernel. > > That's a good idea in my opinion. Great. Patch will be sent out later. thanks, rui -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/acpi/power.c b/drivers/acpi/power.c index 9ac2a9f..0d681fb 100644 --- a/drivers/acpi/power.c +++ b/drivers/acpi/power.c @@ -500,14 +500,14 @@ int acpi_power_transition(struct acpi_device *device, int state) { int result; - if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3)) + if (!device || (state < ACPI_STATE_D0) || (state > ACPI_STATE_D3_COLD)) return -EINVAL; if (device->power.state == state) return 0; if ((device->power.state < ACPI_STATE_D0) - || (device->power.state > ACPI_STATE_D3)) + || (device->power.state > ACPI_STATE_D3_COLD)) return -ENODEV; /* TBD: Resources must be ordered. */ diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c index 8ab80ba..a9d4391 100644 --- a/drivers/acpi/scan.c +++ b/drivers/acpi/scan.c @@ -881,8 +881,16 @@ static int acpi_bus_get_power_flags(struct acpi_device *device) device->power.flags.power_resources = 1; ps->flags.valid = 1; - for (j = 0; j < ps->resources.count; j++) + for (j = 0; j < ps->resources.count; j++) { acpi_bus_add_power_resource(ps->resources.handles[j]); + /* Check for D3_COLD support. _PR3._OFF equals D3_COLD ? */ + if (i == ACPI_STATE_D3) { + if (j == 0) + device->power.states[ACPI_STATE_D3_COLD].flags.valid = 1; + status = acpi_get_handle(ps->resources.handles[j], "_OFF", &handle); + device->power.states[ACPI_STATE_D3_COLD].flags.valid &= ACPI_SUCCESS(status); + } + } } /* Evaluate "_PSx" to see if we can do explicit sets */