diff mbox

[RFC,7/7] ARM: davinci: add support for the am1808 based enbw_cmc board

Message ID 1327308967-8092-8-git-send-email-hs@denx.de
State Not Applicable
Headers show

Commit Message

Heiko Schocher Jan. 23, 2012, 8:56 a.m. UTC 
- AM1808 based board
- 64 MiB DDR ram
- 2 MiB Nor flash
- 128 MiB NAND flash
- use internal RTC
- I2C support
- hwmon lm75 support
- UBI/UBIFS support
- MMC support
- USB OTG support

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: linux-mtd@lists.infradead.org
Cc: linux-i2c@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Wolfgang Denk <wd@denx.de>

---
- post this board support with USB support, even though
  USB is only working with the 10 ms "workaround", posted here:
  http://comments.gmane.org/gmane.linux.usb.general/54505
  I see this issue also on the AM1808 TMDXEXP1808L evalboard.
- MMC and USB are not using OF support yet, ideas how to port
  this are welcome. I need for USB and MMC boards board
  specific callbacks, how to solve this with OF support?

 arch/arm/boot/dts/enbw_cmc.dts                  |  286 +++++++++++++++++
 arch/arm/configs/enbw_cmc_defconfig             |  125 ++++++++
 arch/arm/mach-davinci/Kconfig                   |    8 +
 arch/arm/mach-davinci/Makefile                  |    1 +
 arch/arm/mach-davinci/board-enbw-cmc.c          |  384 +++++++++++++++++++++++
 arch/arm/mach-davinci/include/mach/uncompress.h |    1 +
 6 files changed, 805 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/boot/dts/enbw_cmc.dts
 create mode 100644 arch/arm/configs/enbw_cmc_defconfig
 create mode 100644 arch/arm/mach-davinci/board-enbw-cmc.c

Comments

Grant Likely Jan. 30, 2012, 8:32 p.m. UTC | #1 
On Mon, Jan 23, 2012 at 09:56:07AM +0100, Heiko Schocher wrote:
> - AM1808 based board
> - 64 MiB DDR ram
> - 2 MiB Nor flash
> - 128 MiB NAND flash
> - use internal RTC
> - I2C support
> - hwmon lm75 support
> - UBI/UBIFS support
> - MMC support
> - USB OTG support
> 
> Signed-off-by: Heiko Schocher <hs@denx.de>
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: devicetree-discuss@lists.ozlabs.org
> Cc: davinci-linux-open-source@linux.davincidsp.com
> Cc: linux-mtd@lists.infradead.org
> Cc: linux-i2c@vger.kernel.org
> Cc: netdev@vger.kernel.org
> Cc: David Woodhouse <dwmw2@infradead.org>
> Cc: Ben Dooks <ben-linux@fluff.org>
> Cc: Wolfram Sang <w.sang@pengutronix.de>
> Cc: Sekhar Nori <nsekhar@ti.com>
> Cc: Kevin Hilman <khilman@ti.com>
> Cc: Wolfgang Denk <wd@denx.de>
> 
> ---
> - post this board support with USB support, even though
>   USB is only working with the 10 ms "workaround", posted here:
>   http://comments.gmane.org/gmane.linux.usb.general/54505
>   I see this issue also on the AM1808 TMDXEXP1808L evalboard.
> - MMC and USB are not using OF support yet, ideas how to port
>   this are welcome. I need for USB and MMC boards board
>   specific callbacks, how to solve this with OF support?
> 
>  arch/arm/boot/dts/enbw_cmc.dts                  |  286 +++++++++++++++++
>  arch/arm/configs/enbw_cmc_defconfig             |  125 ++++++++
>  arch/arm/mach-davinci/Kconfig                   |    8 +
>  arch/arm/mach-davinci/Makefile                  |    1 +
>  arch/arm/mach-davinci/board-enbw-cmc.c          |  384 +++++++++++++++++++++++
>  arch/arm/mach-davinci/include/mach/uncompress.h |    1 +
>  6 files changed, 805 insertions(+), 0 deletions(-)
>  create mode 100644 arch/arm/boot/dts/enbw_cmc.dts
>  create mode 100644 arch/arm/configs/enbw_cmc_defconfig
>  create mode 100644 arch/arm/mach-davinci/board-enbw-cmc.c
> 
> diff --git a/arch/arm/boot/dts/enbw_cmc.dts b/arch/arm/boot/dts/enbw_cmc.dts
> new file mode 100644
> index 0000000..e5995ce
> --- /dev/null
> +++ b/arch/arm/boot/dts/enbw_cmc.dts
> @@ -0,0 +1,286 @@
> +/*
> + * Device Tree for the EnBW CMC plattform
> + *
> + * Copyright 2011 DENX Software Engineering GmbH
> + * Heiko Schocher <hs@denx.de>
> + *
> + * This program is free software; you can redistribute  it and/or modify it
> + * under  the terms of  the GNU General  Public License as published by the
> + * Free Software Foundation;  either version 2 of the  License, or (at your
> + * option) any later version.
> + */
> +/dts-v1/;
> +/include/ "skeleton.dtsi"
> +
> +/ {
> +	model = "EnBW CMC";
> +	compatible = "enbw,cmc";
> +
> +	aliases {
> +		ethernet0 = &eth0;
> +	};
> +
> +	arm {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0xfffee000 0x00020000>;
> +		intc: interrupt-controller@1 {
> +			compatible = "ti,davinci-intc";
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +			ti,intc-size = <101>;
> +			reg = <0x0 0x2000>;
> +		};
> +	};
> +	soc@1c00000 {
> +		compatible = "ti,da8xx";

As previously mentioned, using wildcard ('x') characters in compatible
properties is bad practice.  Always be specific and use the compatible
list to make sure the correct driver gets bound (assuming the device
is 100% register level compatible with the older one).

> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0x0 0x01c00000 0x400000>;
> +
> +		serial0: serial@1c42000 {
> +			cell-index = <2>;

As previously mentioned, don't use cell index.  If you *really* need
to assign a number to a device, then use a property in the /aliases
node and make sure pdev->id does *not* get modified.

> +			compatible = "ns16550a";

Should include a string for the specific device.  Something like:

	compatible = "ti,da800", "ns16550a";

> diff --git a/arch/arm/mach-davinci/board-enbw-cmc.c b/arch/arm/mach-davinci/board-enbw-cmc.c
> new file mode 100644
> index 0000000..4473c4a
> --- /dev/null
> +++ b/arch/arm/mach-davinci/board-enbw-cmc.c
> @@ -0,0 +1,384 @@
> +/*
> + * EnBW Communication Module Compact board
> + * Copyright 2011 DENX Software Engineering GmbH
> + * Author: Heiko Schocher <hs@denx.de>
> + *
> + * based on:
> + * TI DA850/OMAP-L138 EVM board
> + *
> + * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * Derived from: arch/arm/mach-davinci/board-da850-evm.c
> + * Original Copyrights follow:
> + *
> + * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
> + * the terms of the GNU General Public License version 2. This program
> + * is licensed "as is" without any warranty of any kind, whether express
> + * or implied.
> + */
> +#include <linux/console.h>
> +#include <linux/gpio.h>
> +#include <linux/gpio_keys.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/mtd/mtd.h>
> +#include <linux/mtd/nand.h>
> +#include <linux/mtd/partitions.h>
> +#include <linux/mtd/physmap.h>
> +#include <linux/of.h>
> +#include <linux/of_net.h>
> +#include <linux/of_address.h>
> +#include <linux/of_platform.h>
> +#include <linux/phy.h>
> +#include <linux/phy_fixed.h>
> +#include <linux/platform_device.h>
> +#include <linux/spi/spi.h>
> +#include <linux/spi/flash.h>
> +#include <asm/mach-types.h>
> +#include <asm/mach/arch.h>
> +#include <mach/aemif.h>
> +#include <mach/cp_intc.h>
> +#include <mach/da8xx.h>
> +#include <mach/mux.h>
> +#include <mach/nand.h>
> +#include <mach/spi.h>
> +
> +#define ENBW_CMC_MMCSD_CD_PIN          GPIO_TO_PIN(3, 13)
> +
> +/*
> + * USB1 VBUS is controlled by GPIO7[12], over-current is reported on GPIO7[8].
> + */
> +#define DA850_USB_VBUS_PIN	GPIO_TO_PIN(7, 12)
> +#define ON_BD_USB_OVC		GPIO_TO_PIN(7, 8)
> +
> +#if defined(CONFIG_USB_OHCI_HCD)
> +static irqreturn_t enbw_cmc_usb_ocic_irq(int irq, void *dev_id);
> +static da8xx_ocic_handler_t enbw_cmc_usb_ocic_handler;
> +
> +static int enbw_cmc_usb_set_power(unsigned port, int on)
> +{
> +	gpio_set_value(DA850_USB_VBUS_PIN, on);
> +	return 0;
> +}
> +
> +static int enbw_cmc_usb_get_power(unsigned port)
> +{
> +	return gpio_get_value(DA850_USB_VBUS_PIN);
> +}
> +
> +static int enbw_cmc_usb_get_oci(unsigned port)
> +{
> +	return !gpio_get_value(ON_BD_USB_OVC);
> +}
> +
> +static irqreturn_t enbw_cmc_usb_ocic_irq(int, void *);
> +
> +static int enbw_cmc_usb_ocic_notify(da8xx_ocic_handler_t handler)
> +{
> +	int irq         = gpio_to_irq(ON_BD_USB_OVC);
> +	int error       = 0;
> +
> +	if (handler != NULL) {
> +		enbw_cmc_usb_ocic_handler = handler;
> +
> +		error = request_irq(irq, enbw_cmc_usb_ocic_irq,
> +					IRQF_DISABLED | IRQF_TRIGGER_RISING |
> +					IRQF_TRIGGER_FALLING,
> +					"OHCI over-current indicator", NULL);
> +		if (error)
> +			pr_err("%s: could not request IRQ to watch "
> +				"over-current indicator changes\n", __func__);
> +	} else {
> +		free_irq(irq, NULL);
> +	}
> +	return error;
> +}
> +
> +static struct da8xx_ohci_root_hub enbw_cmc_usb11_pdata = {
> +	.set_power      = enbw_cmc_usb_set_power,
> +	.get_power      = enbw_cmc_usb_get_power,
> +	.get_oci        = enbw_cmc_usb_get_oci,
> +	.ocic_notify    = enbw_cmc_usb_ocic_notify,
> +	.potpgt         = (10 + 1) / 2,  /* 10 ms max */
> +};
> +
> +static irqreturn_t enbw_cmc_usb_ocic_irq(int irq, void *dev_id)
> +{
> +	enbw_cmc_usb_ocic_handler(&enbw_cmc_usb11_pdata, 1);
> +	return IRQ_HANDLED;
> +}
> +#endif
> +
> +#if defined(CONFIG_OF)
> +static __init void enbw_cmc_usb_init(void)

All the focus is on DT now.  How about making CONFIG_OF required for
this board?  Also, this is just another board file.  The focus should
be on creating a generic board support file for DT platforms.
Heiko Schocher Jan. 31, 2012, 1:04 p.m. UTC | #2 
Hello Grant,

Grant Likely wrote:
> On Mon, Jan 23, 2012 at 09:56:07AM +0100, Heiko Schocher wrote:
>> - AM1808 based board
>> - 64 MiB DDR ram
>> - 2 MiB Nor flash
>> - 128 MiB NAND flash
>> - use internal RTC
>> - I2C support
>> - hwmon lm75 support
>> - UBI/UBIFS support
>> - MMC support
>> - USB OTG support
>>
>> Signed-off-by: Heiko Schocher <hs@denx.de>
>> Cc: linux-arm-kernel@lists.infradead.org
>> Cc: devicetree-discuss@lists.ozlabs.org
>> Cc: davinci-linux-open-source@linux.davincidsp.com
>> Cc: linux-mtd@lists.infradead.org
>> Cc: linux-i2c@vger.kernel.org
>> Cc: netdev@vger.kernel.org
>> Cc: David Woodhouse <dwmw2@infradead.org>
>> Cc: Ben Dooks <ben-linux@fluff.org>
>> Cc: Wolfram Sang <w.sang@pengutronix.de>
>> Cc: Sekhar Nori <nsekhar@ti.com>
>> Cc: Kevin Hilman <khilman@ti.com>
>> Cc: Wolfgang Denk <wd@denx.de>
>>
>> ---
>> - post this board support with USB support, even though
>>   USB is only working with the 10 ms "workaround", posted here:
>>   http://comments.gmane.org/gmane.linux.usb.general/54505
>>   I see this issue also on the AM1808 TMDXEXP1808L evalboard.
>> - MMC and USB are not using OF support yet, ideas how to port
>>   this are welcome. I need for USB and MMC boards board
>>   specific callbacks, how to solve this with OF support?

Can you give me a hint, how to add callbacks to OF support?

>>  arch/arm/boot/dts/enbw_cmc.dts                  |  286 +++++++++++++++++
>>  arch/arm/configs/enbw_cmc_defconfig             |  125 ++++++++
>>  arch/arm/mach-davinci/Kconfig                   |    8 +
>>  arch/arm/mach-davinci/Makefile                  |    1 +
>>  arch/arm/mach-davinci/board-enbw-cmc.c          |  384 +++++++++++++++++++++++
>>  arch/arm/mach-davinci/include/mach/uncompress.h |    1 +
>>  6 files changed, 805 insertions(+), 0 deletions(-)
>>  create mode 100644 arch/arm/boot/dts/enbw_cmc.dts
>>  create mode 100644 arch/arm/configs/enbw_cmc_defconfig
>>  create mode 100644 arch/arm/mach-davinci/board-enbw-cmc.c
>>
>> diff --git a/arch/arm/boot/dts/enbw_cmc.dts b/arch/arm/boot/dts/enbw_cmc.dts
>> new file mode 100644
>> index 0000000..e5995ce
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/enbw_cmc.dts
>> @@ -0,0 +1,286 @@
>> +/*
>> + * Device Tree for the EnBW CMC plattform
>> + *
>> + * Copyright 2011 DENX Software Engineering GmbH
>> + * Heiko Schocher <hs@denx.de>
>> + *
>> + * This program is free software; you can redistribute  it and/or modify it
>> + * under  the terms of  the GNU General  Public License as published by the
>> + * Free Software Foundation;  either version 2 of the  License, or (at your
>> + * option) any later version.
>> + */
>> +/dts-v1/;
>> +/include/ "skeleton.dtsi"
>> +
>> +/ {
>> +	model = "EnBW CMC";
>> +	compatible = "enbw,cmc";
>> +
>> +	aliases {
>> +		ethernet0 = &eth0;
>> +	};
>> +
>> +	arm {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges = <0 0xfffee000 0x00020000>;
>> +		intc: interrupt-controller@1 {
>> +			compatible = "ti,davinci-intc";
>> +			interrupt-controller;
>> +			#interrupt-cells = <1>;
>> +			ti,intc-size = <101>;
>> +			reg = <0x0 0x2000>;
>> +		};
>> +	};
>> +	soc@1c00000 {
>> +		compatible = "ti,da8xx";
> 
> As previously mentioned, using wildcard ('x') characters in compatible
> properties is bad practice.  Always be specific and use the compatible
> list to make sure the correct driver gets bound (assuming the device
> is 100% register level compatible with the older one).

fixed.

>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges = <0x0 0x01c00000 0x400000>;
>> +
>> +		serial0: serial@1c42000 {
>> +			cell-index = <2>;
> 
> As previously mentioned, don't use cell index.  If you *really* need
> to assign a number to a device, then use a property in the /aliases
> node and make sure pdev->id does *not* get modified.

removed, as not needed.

>> +			compatible = "ns16550a";
> 
> Should include a string for the specific device.  Something like:
> 
> 	compatible = "ti,da800", "ns16550a";

added.

>> diff --git a/arch/arm/mach-davinci/board-enbw-cmc.c b/arch/arm/mach-davinci/board-enbw-cmc.c
>> new file mode 100644
>> index 0000000..4473c4a
>> --- /dev/null
>> +++ b/arch/arm/mach-davinci/board-enbw-cmc.c
>> @@ -0,0 +1,384 @@
[...]
>> +#if defined(CONFIG_OF)
>> +static __init void enbw_cmc_usb_init(void)
> 
> All the focus is on DT now.  How about making CONFIG_OF required for
> this board?  Also, this is just another board file.  The focus should

fixed.

> be on creating a generic board support file for DT platforms.

move the arch/arm/mach-davinci/board-enbw-cmc.c to
arch/arm/mach-davinci/board-da850_simple.c

and do it like

arch/powerpc/platforms/52xx/mpc5200_simple.c ?

and extract common nodes from arch/arm/boot/dts/enbw_cmc.dts
to arch/arm/boot/dts/da850.dtsi?

bye,
Heiko
Sergei Shtylyov Feb. 1, 2012, 10:20 a.m. UTC | #3 
Hello.

On 31-01-2012 17:04, Heiko Schocher wrote:

>> On Mon, Jan 23, 2012 at 09:56:07AM +0100, Heiko Schocher wrote:
>>> - AM1808 based board
>>> - 64 MiB DDR ram
>>> - 2 MiB Nor flash
>>> - 128 MiB NAND flash
>>> - use internal RTC
>>> - I2C support
>>> - hwmon lm75 support
>>> - UBI/UBIFS support
>>> - MMC support
>>> - USB OTG support

>>> Signed-off-by: Heiko Schocher<hs@denx.de>
>>> Cc: linux-arm-kernel@lists.infradead.org
>>> Cc: devicetree-discuss@lists.ozlabs.org
>>> Cc: davinci-linux-open-source@linux.davincidsp.com
>>> Cc: linux-mtd@lists.infradead.org
>>> Cc: linux-i2c@vger.kernel.org
>>> Cc: netdev@vger.kernel.org
>>> Cc: David Woodhouse<dwmw2@infradead.org>
>>> Cc: Ben Dooks<ben-linux@fluff.org>
>>> Cc: Wolfram Sang<w.sang@pengutronix.de>
>>> Cc: Sekhar Nori<nsekhar@ti.com>
>>> Cc: Kevin Hilman<khilman@ti.com>
>>> Cc: Wolfgang Denk<wd@denx.de>

>>> ---
>>> - post this board support with USB support, even though
>>>    USB is only working with the 10 ms "workaround", posted here:
>>>    http://comments.gmane.org/gmane.linux.usb.general/54505
>>>    I see this issue also on the AM1808 TMDXEXP1808L evalboard.
>>> - MMC and USB are not using OF support yet, ideas how to port
>>>    this are welcome. I need for USB and MMC boards board
>>>    specific callbacks, how to solve this with OF support?

[...]

>>> diff --git a/arch/arm/boot/dts/enbw_cmc.dts b/arch/arm/boot/dts/enbw_cmc.dts
>>> new file mode 100644
>>> index 0000000..e5995ce
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/enbw_cmc.dts
[...]

>>> +			compatible = "ns16550a";

>> Should include a string for the specific device.  Something like:

>> 	compatible = "ti,da800", "ns16550a";

> added.

    Note that there's no DA800 chip, only DA828, DA830, and DA850 AFAIK.

WBR, Sergei
Grant Likely Feb. 2, 2012, 12:17 a.m. UTC | #4 
On Wed, Feb 01, 2012 at 02:20:13PM +0400, Sergei Shtylyov wrote:
> Hello.
> 
> On 31-01-2012 17:04, Heiko Schocher wrote:
> 
> >>On Mon, Jan 23, 2012 at 09:56:07AM +0100, Heiko Schocher wrote:
> >>>- AM1808 based board
> >>>- 64 MiB DDR ram
> >>>- 2 MiB Nor flash
> >>>- 128 MiB NAND flash
> >>>- use internal RTC
> >>>- I2C support
> >>>- hwmon lm75 support
> >>>- UBI/UBIFS support
> >>>- MMC support
> >>>- USB OTG support
> 
> >>>Signed-off-by: Heiko Schocher<hs@denx.de>
> >>>Cc: linux-arm-kernel@lists.infradead.org
> >>>Cc: devicetree-discuss@lists.ozlabs.org
> >>>Cc: davinci-linux-open-source@linux.davincidsp.com
> >>>Cc: linux-mtd@lists.infradead.org
> >>>Cc: linux-i2c@vger.kernel.org
> >>>Cc: netdev@vger.kernel.org
> >>>Cc: David Woodhouse<dwmw2@infradead.org>
> >>>Cc: Ben Dooks<ben-linux@fluff.org>
> >>>Cc: Wolfram Sang<w.sang@pengutronix.de>
> >>>Cc: Sekhar Nori<nsekhar@ti.com>
> >>>Cc: Kevin Hilman<khilman@ti.com>
> >>>Cc: Wolfgang Denk<wd@denx.de>
> 
> >>>---
> >>>- post this board support with USB support, even though
> >>>   USB is only working with the 10 ms "workaround", posted here:
> >>>   http://comments.gmane.org/gmane.linux.usb.general/54505
> >>>   I see this issue also on the AM1808 TMDXEXP1808L evalboard.
> >>>- MMC and USB are not using OF support yet, ideas how to port
> >>>   this are welcome. I need for USB and MMC boards board
> >>>   specific callbacks, how to solve this with OF support?
> 
> [...]
> 
> >>>diff --git a/arch/arm/boot/dts/enbw_cmc.dts b/arch/arm/boot/dts/enbw_cmc.dts
> >>>new file mode 100644
> >>>index 0000000..e5995ce
> >>>--- /dev/null
> >>>+++ b/arch/arm/boot/dts/enbw_cmc.dts
> [...]
> 
> >>>+			compatible = "ns16550a";
> 
> >>Should include a string for the specific device.  Something like:
> 
> >>	compatible = "ti,da800", "ns16550a";
> 
> >added.
> 
>    Note that there's no DA800 chip, only DA828, DA830, and DA850 AFAIK.

Right, so the compatible string should reflect that.

g.
diff mbox

Patch

diff --git a/arch/arm/boot/dts/enbw_cmc.dts b/arch/arm/boot/dts/enbw_cmc.dts
new file mode 100644
index 0000000..e5995ce
--- /dev/null
+++ b/arch/arm/boot/dts/enbw_cmc.dts
@@ -0,0 +1,286 @@ 
+/*
+ * Device Tree for the EnBW CMC plattform
+ *
+ * Copyright 2011 DENX Software Engineering GmbH
+ * Heiko Schocher <hs@denx.de>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+/dts-v1/;
+/include/ "skeleton.dtsi"
+
+/ {
+	model = "EnBW CMC";
+	compatible = "enbw,cmc";
+
+	aliases {
+		ethernet0 = &eth0;
+	};
+
+	arm {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xfffee000 0x00020000>;
+		intc: interrupt-controller@1 {
+			compatible = "ti,davinci-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			ti,intc-size = <101>;
+			reg = <0x0 0x2000>;
+		};
+	};
+	soc@1c00000 {
+		compatible = "ti,da8xx";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x01c00000 0x400000>;
+
+		serial0: serial@1c42000 {
+			cell-index = <2>;
+			compatible = "ns16550a";
+			reg = <0x42000 0x100>;
+			clock-frequency = <150000000>;
+			reg-shift = <2>;
+			interrupts = <25>;
+			interrupt-parent = <&intc>;
+		};
+		serial1: serial@1d0c000 {
+			cell-index = <1>;
+			compatible = "ns16550a";
+			reg = <0x10c000 0x100>;
+			clock-frequency = <150000000>;
+			reg-shift = <2>;
+			interrupts = <53>;
+			interrupt-parent = <&intc>;
+		};
+		serial2: serial@1d0d000 {
+			cell-index = <2>;
+			compatible = "ns16550a";
+			reg = <0x10d000 0x100>;
+			clock-frequency = <150000000>;
+			reg-shift = <2>;
+			interrupts = <61>;
+			interrupt-parent = <&intc>;
+		};
+
+		nor_pins: nor_pinmux@1c14120 {
+			compatible = "ti,davinci-pinmux";
+			reg = <0x14120 0x1000>;
+			pins = < /*	muxreg	maskoff	modemsk muxmode */
+					5	24	15	1 /* EMA_BA_1 */
+					6	0	15	1 /* EMA CLK */
+					6	24	15	1 /* EMA_WAIT_1 */
+					7	0	15	1 /* NEMA_CS_2 */
+					7	16	15	1 /* NEMA_WE */
+					7	20	15	1 /* NEMA_OE */
+					9	28	15	1 /* EMA_D_0 */
+					9	24	15	1 /* EMA_D_1 */
+					9	20	15	1 /* EMA_D_2 */
+					9	16	15	1 /* EMA_D_3 */
+					9	12	15	1 /* EMA_D_4 */
+					9	8	15	1 /* EMA_D_5 */
+					9	4	15	1 /* EMA_D_6 */
+					9	0	15	1 /* EMA_D_7 */
+					8	28	15	1 /* EMA_D_8 */
+					8	24	15	1 /* EMA_D_9 */
+					8	20	15	1 /* EMA_D_10 */
+					8	16	15	1 /* EMA_D_11 */
+					8	12	15	1 /* EMA_D_12 */
+					8	8	15	1 /* EMA_D_13 */
+					8	4	15	1 /* EMA_D_14 */
+					8	0	15	1 /* EMA_D_15 */
+					12	28	15	1 /* EMA_A_0 */
+					12	24	15	1 /* EMA_A_1 */
+					12	20	15	1 /* EMA_A_2 */
+					12	16	15	1 /* EMA_A_3 */
+					12	12	15	1 /* EMA_A_4 */
+					12	8	15	1 /* EMA_A_5 */
+					12	4	15	1 /* EMA_A_6 */
+					12	0	15	1 /* EMA_A_7 */
+					11	28	15	1 /* EMA_A_8 */
+					11	24	15	1 /* EMA_A_9 */
+					11	20	15	1 /* EMA_A_10 */
+					11	16	15	1 /* EMA_A_11 */
+					11	12	15	1 /* EMA_A_12 */
+					11	8	15	1 /* EMA_A_13 */
+					11	4	15	1 /* EMA_A_14 */
+					11	0	15	1 /* EMA_A_15 */
+					10	28	15	1 /* EMA_A_16 */
+					10	24	15	1 /* EMA_A_17 */
+					10	20	15	1 /* EMA_A_18 */
+					10	16	15	1 /* EMA_A_19 */
+					10	12	15	1 /* EMA_A_20 */
+					10	8	15	1 /* EMA_A_21 */
+					10	4	15	1 /* EMA_A_22 */
+					10	0	15	1 /* EMA_A_23 */
+				>;
+		};
+		nand_pins: nand_pinmux@1c14120 {
+			compatible = "ti,davinci-pinmux";
+			reg = <0x14120 0x1000>;
+			pins = < /*	muxreg	maskoff	modemsk muxmode */
+					7	4	15	1 /* NEMA_CS_3 */
+				>;
+		};
+
+		emac_pins: pinmux@1c14120 {
+			compatible = "ti,davinci-pinmux";
+			reg = <0x14120 0x1000>;
+			pins = < /*	muxreg	maskoff	modemsk muxmode */
+					2	4	15	8 /* MII TXEN */
+					2	8	15	8 /* MII TXCLK */
+					2	12	15	8 /* MII COL */
+					2	16	15	8 /* MII TXD_3 */
+					2	20	15	8 /* MII TXD_2 */
+					2	24	15	8 /* MII TXD_1 */
+					2	28	15	8 /* MII TXD_0 */
+					3	8	15	8 /* MII RXER */
+					3	12	15	8 /* MII CRS */
+					3	0	15	8 /* MII RXCLK */
+					3	4	15	8 /* MII RXDV */
+					3	16	15	8 /* MII RXD_3 */
+					3	20	15	8 /* MII RXD_2 */
+					3	24	15	8 /* MII RXD_1 */
+					3	28	15	8 /* MII RXD_0 */
+					4	0	15	8 /* MDIO CLK */
+					4	4	15	8 /* MDIO D */
+				>;
+		};
+
+		i2c1_pins: i2c_pinmux@1c14120 {
+			compatible = "ti,davinci-pinmux";
+			reg = <0x14120 0x1000>;
+			pins = < /*	muxreg	maskoff	modemsk muxmode */
+					4	12	15	2 /* I2C0 SDA */
+					4	8	15	2 /* I2C0 SCL */
+				>;
+		};
+
+		eth0: emac@1e20000 {
+			compatible = "ti,davinci-emac";
+			reg = <0x220000 0x4000>;
+			ctrl_reg_offset = <0x3000>;
+			ctrl_mod_reg_offset = <0x2000>;
+			ctrl_ram_offset = <0>;
+			hw_ram_addr = <0>;
+			ctrl_ram_size = <0x2000>;
+			version = <1>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupts = <33
+					34
+					35
+					36
+					>;
+			interrupt-parent = <&intc>;
+			pinmux-handle = <&emac_pins>;
+		};
+
+		i2c@1c22000 {
+			compatible = "ti,davinci-i2c";
+			reg = <0x22000 0x1000>;
+			clock-frequency = <100000>;
+			interrupts = <15>;
+			interrupt-parent = <&intc>;
+			id = <1>;
+			pinmux-handle = <&i2c1_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dtt@48 {
+					compatible = "national,lm75";
+					reg = <0x48>;
+				};
+		};
+
+		wdt@1c21000 {
+			compatible = "ti,davinci-wdt";
+			reg = <0x00021000 0x1000>;
+			period = <100>;
+		};
+		bootcount@1c23000 {
+			compatible = "uboot,bootcount";
+			reg = <0x23060 0x20>;
+		};
+
+	};
+	onchipram@8000000 {
+		compatible = "ti,davinci-onchipram";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x80000000 0x20000>;
+	};
+	aemif@60000000 {
+		compatible = "ti,davinci-aemif";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <0x68000000 0x80000>;
+		ranges = <2 0 0x60000000 0x02000000
+			  3 0 0x62000000 0x02000000
+			  4 0 0x64000000 0x02000000
+			  5 0 0x66000000 0x02000000
+			  6 0 0x68000000 0x02000000>;
+		cs2@68000000 {
+			compatible = "ti,davinci-cs";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* all timings in nanoseconds */
+			cs = <2>;
+			asize = <1>;
+			ta = <0>;
+			rhold = <7>;
+			rstrobe = <42>;
+			rsetup = <14>;
+			whold = <7>;
+			wstrobe = <42>;
+			wsetup = <14>;
+			ew = <0>;
+			ss = <0>;
+		};
+		flash@2,0 {
+			compatible = "cfi-flash";
+			reg = <2 0x0 0x400000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bank-width = <2>;
+			device-width = <2>;
+		};
+		nand_cs: cs3@68000000 {
+			compatible = "ti,davinci-cs";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* all timings in nanoseconds */
+			cs = <3>;
+			asize = <0>;
+			ta = <0>;
+			rhold = <7>;
+			rstrobe = <42>;
+			rsetup = <7>;
+			whold = <7>;
+			wstrobe = <14>;
+			wsetup = <7>;
+			ew = <0>;
+			ss = <0>;
+		};
+		nandflash@3,0 {
+			compatible = "ti,davinci-nand";
+			reg = <3 0x0 0x807ff
+				6 0x0 0x8000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			id = <1>;
+			mask_ale = <0>;
+			mask_cle = <0>;
+			mask_chipsel = <0>;
+			ecc_mode = <2>;
+			ecc_bits = <4>;
+			options = <0>;
+			bbt_options = <0x20000>;
+			pinmux-handle = <&nand_pins>;
+			timing-handle = <&nand_cs>;
+		};
+
+	};
+};
diff --git a/arch/arm/configs/enbw_cmc_defconfig b/arch/arm/configs/enbw_cmc_defconfig
new file mode 100644
index 0000000..c794127
--- /dev/null
+++ b/arch/arm/configs/enbw_cmc_defconfig
@@ -0,0 +1,125 @@ 
+CONFIG_EXPERIMENTAL=y
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_DAVINCI=y
+CONFIG_ARCH_DAVINCI_DA850=y
+# CONFIG_MACH_DAVINCI_DA850_EVM is not set
+CONFIG_GPIO_PCA953X=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_USE_OF=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_INET_LRO is not set
+CONFIG_IPV6=y
+CONFIG_NETFILTER=y
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_DAVINCI=y
+CONFIG_MTD_UBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=1
+CONFIG_BLK_DEV_RAM_SIZE=32768
+CONFIG_MISC_DEVICES=y
+CONFIG_UBOOT_BOOTCOUNT=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_NETDEVICES=y
+CONFIG_MII=y
+CONFIG_TI_DAVINCI_EMAC=y
+# CONFIG_WLAN is not set
+CONFIG_INPUT_POLLDEV=y
+# CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_EVBUG=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=3
+CONFIG_SERIAL_8250_RUNTIME_UARTS=3
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_DAVINCI=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_PCF857X=y
+CONFIG_SENSORS_LM75=y
+CONFIG_WATCHDOG=y
+CONFIG_WD=y
+CONFIG_WD_DAVINCI=y
+# CONFIG_HID_SUPPORT is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_DA8XX=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_UAS=y
+CONFIG_USB_LIBUSUAL=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_FUSB300=y
+CONFIG_USB_ETH=y
+CONFIG_MMC=y
+CONFIG_MMC_DAVINCI=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_OMAP=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_CRAMFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_ROOT_NFS=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_DEBUG_FS=y
+CONFIG_TIMER_STATS=y
+CONFIG_DEBUG_RT_MUTEXES=y
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_CCITT=m
+CONFIG_CRC_T10DIF=m
diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig
index 32d837d..66efe86 100644
--- a/arch/arm/mach-davinci/Kconfig
+++ b/arch/arm/mach-davinci/Kconfig
@@ -202,6 +202,14 @@  config DA850_WL12XX
 	  Say Y if you want to use a wl1271 expansion card connected to the
 	  AM18x EVM.
 
+config MACH_ENBW_CMC
+	bool "EnBW Communication Module Compact"
+	default ARCH_DAVINCI_DA850
+	depends on ARCH_DAVINCI_DA850
+	help
+	  Say Y here to select the EnBW Communication Module Compact
+	  board.
+
 config GPIO_PCA953X
 	default MACH_DAVINCI_DA850_EVM
 
diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile
index 2db78bd..12f3166 100644
--- a/arch/arm/mach-davinci/Makefile
+++ b/arch/arm/mach-davinci/Makefile
@@ -34,6 +34,7 @@  obj-$(CONFIG_MACH_DAVINCI_DA850_EVM)	+= board-da850-evm.o
 obj-$(CONFIG_MACH_TNETV107X)		+= board-tnetv107x-evm.o
 obj-$(CONFIG_MACH_MITYOMAPL138)		+= board-mityomapl138.o
 obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD)	+= board-omapl138-hawk.o
+obj-$(CONFIG_MACH_ENBW_CMC)		+= board-enbw-cmc.o
 
 # Power Management
 obj-$(CONFIG_CPU_FREQ)			+= cpufreq.o
diff --git a/arch/arm/mach-davinci/board-enbw-cmc.c b/arch/arm/mach-davinci/board-enbw-cmc.c
new file mode 100644
index 0000000..4473c4a
--- /dev/null
+++ b/arch/arm/mach-davinci/board-enbw-cmc.c
@@ -0,0 +1,384 @@ 
+/*
+ * EnBW Communication Module Compact board
+ * Copyright 2011 DENX Software Engineering GmbH
+ * Author: Heiko Schocher <hs@denx.de>
+ *
+ * based on:
+ * TI DA850/OMAP-L138 EVM board
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Derived from: arch/arm/mach-davinci/board-da850-evm.c
+ * Original Copyrights follow:
+ *
+ * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#include <linux/console.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/phy_fixed.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/aemif.h>
+#include <mach/cp_intc.h>
+#include <mach/da8xx.h>
+#include <mach/mux.h>
+#include <mach/nand.h>
+#include <mach/spi.h>
+
+#define ENBW_CMC_MMCSD_CD_PIN          GPIO_TO_PIN(3, 13)
+
+/*
+ * USB1 VBUS is controlled by GPIO7[12], over-current is reported on GPIO7[8].
+ */
+#define DA850_USB_VBUS_PIN	GPIO_TO_PIN(7, 12)
+#define ON_BD_USB_OVC		GPIO_TO_PIN(7, 8)
+
+#if defined(CONFIG_USB_OHCI_HCD)
+static irqreturn_t enbw_cmc_usb_ocic_irq(int irq, void *dev_id);
+static da8xx_ocic_handler_t enbw_cmc_usb_ocic_handler;
+
+static int enbw_cmc_usb_set_power(unsigned port, int on)
+{
+	gpio_set_value(DA850_USB_VBUS_PIN, on);
+	return 0;
+}
+
+static int enbw_cmc_usb_get_power(unsigned port)
+{
+	return gpio_get_value(DA850_USB_VBUS_PIN);
+}
+
+static int enbw_cmc_usb_get_oci(unsigned port)
+{
+	return !gpio_get_value(ON_BD_USB_OVC);
+}
+
+static irqreturn_t enbw_cmc_usb_ocic_irq(int, void *);
+
+static int enbw_cmc_usb_ocic_notify(da8xx_ocic_handler_t handler)
+{
+	int irq         = gpio_to_irq(ON_BD_USB_OVC);
+	int error       = 0;
+
+	if (handler != NULL) {
+		enbw_cmc_usb_ocic_handler = handler;
+
+		error = request_irq(irq, enbw_cmc_usb_ocic_irq,
+					IRQF_DISABLED | IRQF_TRIGGER_RISING |
+					IRQF_TRIGGER_FALLING,
+					"OHCI over-current indicator", NULL);
+		if (error)
+			pr_err("%s: could not request IRQ to watch "
+				"over-current indicator changes\n", __func__);
+	} else {
+		free_irq(irq, NULL);
+	}
+	return error;
+}
+
+static struct da8xx_ohci_root_hub enbw_cmc_usb11_pdata = {
+	.set_power      = enbw_cmc_usb_set_power,
+	.get_power      = enbw_cmc_usb_get_power,
+	.get_oci        = enbw_cmc_usb_get_oci,
+	.ocic_notify    = enbw_cmc_usb_ocic_notify,
+	.potpgt         = (10 + 1) / 2,  /* 10 ms max */
+};
+
+static irqreturn_t enbw_cmc_usb_ocic_irq(int irq, void *dev_id)
+{
+	enbw_cmc_usb_ocic_handler(&enbw_cmc_usb11_pdata, 1);
+	return IRQ_HANDLED;
+}
+#endif
+
+#if defined(CONFIG_OF)
+static __init void enbw_cmc_usb_init(void)
+{
+	int ret;
+	u32 cfgchip2;
+
+	/* Set up USB clock/mode in the CFGCHIP2 register. */
+	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	/* USB2.0 PHY reference clock is AUXCLK with 24MHz */
+	cfgchip2 &= ~CFGCHIP2_REFFREQ;
+	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
+
+	/*
+	 * Select internal reference clock for USB 2.0 PHY
+	 * and use it as a clock source for USB 1.1 PHY
+	 * (this is the default setting anyway).
+	 */
+	cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX;
+	cfgchip2 |=  CFGCHIP2_USB2PHYCLKMUX;
+
+	cfgchip2 &= ~CFGCHIP2_OTGMODE;
+	cfgchip2 |=  CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN;
+
+	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	ret = davinci_cfg_reg(DA830_USB0_DRVVBUS);
+	if (ret)
+		pr_warning("%s: USB 2.0 PinMux setup failed: %d\n",
+			   __func__, ret);
+	else {
+		/*
+		 * SP2525A @ 5V supplies 500mA,
+		 * with the power on to power good time of 10 ms.
+		 */
+		ret = da8xx_register_usb20(500, 10);
+		if (ret)
+			pr_warning("%s: USB 2.0 registration failed: %d\n",
+				   __func__, ret);
+	}
+
+	ret = gpio_request_one(DA850_USB_VBUS_PIN,
+			GPIOF_DIR_OUT, "USB 1.1 VBUS");
+	if (ret < 0) {
+		pr_err("%s: failed to request GPIO for USB 1.1 port "
+			"power control: %d\n", __func__, ret);
+		return;
+	}
+	gpio_direction_input(DA850_USB_VBUS_PIN);
+
+	ret = gpio_request(ON_BD_USB_OVC, "ON_BD_USB_OVC");
+	if (ret) {
+		printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
+		       "over-current indicator: %d\n", __func__, ret);
+		gpio_free(DA850_USB_VBUS_PIN);
+		return;
+	}
+	gpio_direction_input(ON_BD_USB_OVC);
+
+#if defined(CONFIG_USB_OHCI_HCD)
+	ret = da8xx_register_usb11(&enbw_cmc_usb11_pdata);
+	if (ret) {
+		pr_warning("%s: USB 1.1 registration failed: %d\n",
+			   __func__, ret);
+		gpio_free(ON_BD_USB_OVC);
+		gpio_free(DA850_USB_VBUS_PIN);
+	}
+#endif
+
+	return;
+}
+
+static int enbw_cmc_mmc_get_ro(int index)
+{
+	return 0;
+}
+
+static int enbw_cmc_mmc_get_cd(int index)
+{
+	return gpio_get_value(ENBW_CMC_MMCSD_CD_PIN) ? 1 : 0;
+}
+
+static struct davinci_mmc_config enbw_cmc_mmc_config = {
+	.get_ro		= enbw_cmc_mmc_get_ro,
+	.get_cd		= enbw_cmc_mmc_get_cd,
+	.wires		= 4,
+	.max_freq	= 50000000,
+	.caps		= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
+	.version	= MMC_CTLR_VERSION_2,
+};
+
+static int __init enbw_cmc_config_emac(void)
+{
+	void __iomem *cfg_chip3_base;
+	int ret;
+	u32 val;
+	struct davinci_soc_info *soc_info = &davinci_soc_info;
+
+	if (!machine_is_enbw_cmc())
+		return 0;
+
+	cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
+	val = __raw_readl(cfg_chip3_base);
+	val &= ~BIT(8);
+	pr_info("EMAC: MII PHY configured, RMII PHY will not be"
+						" functional\n");
+
+	/* configure the CFGCHIP3 register for MII */
+	__raw_writel(val, cfg_chip3_base);
+
+	/* use complete info from OF */
+	soc_info->emac_pdata = NULL;
+	ret = da8xx_register_emac();
+	if (ret)
+		pr_warning("enbw_cmc_init: emac registration failed: %d\n",
+				ret);
+
+	return 0;
+}
+device_initcall(enbw_cmc_config_emac);
+
+static const s16 da850_dma0_rsv_chans[][2] = {
+	/* (offset, number) */
+	{-1, -1}
+};
+
+static const s16 da850_dma0_rsv_slots[][2] = {
+	/* (offset, number) */
+	{-1, -1}
+};
+
+static const s16 da850_dma1_rsv_chans[][2] = {
+	/* (offset, number) */
+	{-1, -1}
+};
+
+static const s16 da850_dma1_rsv_slots[][2] = {
+	/* (offset, number) */
+	{-1, -1}
+};
+
+static struct edma_rsv_info da850_edma_cc0_rsv = {
+	.rsv_chans	= da850_dma0_rsv_chans,
+	.rsv_slots	= da850_dma0_rsv_slots,
+};
+
+static struct edma_rsv_info da850_edma_cc1_rsv = {
+	.rsv_chans	= da850_dma1_rsv_chans,
+	.rsv_slots	= da850_dma1_rsv_slots,
+};
+
+static struct edma_rsv_info *da850_edma_rsv[2] = {
+	&da850_edma_cc0_rsv,
+	&da850_edma_cc1_rsv,
+};
+
+#ifdef CONFIG_CPU_FREQ
+static __init int da850_evm_init_cpufreq(void)
+{
+	switch (system_rev & 0xF) {
+	case 3:
+		da850_max_speed = 456000;
+		break;
+	case 2:
+		da850_max_speed = 408000;
+		break;
+	case 1:
+		da850_max_speed = 372000;
+		break;
+	}
+
+	return da850_register_cpufreq("pll0_sysclk3");
+}
+#else
+static __init int da850_evm_init_cpufreq(void) { return 0; }
+#endif
+
+struct of_dev_auxdata enbw_cmc_auxdata_lookup[] __initdata = {
+	OF_DEV_AUXDATA("ti,davinci-wdt", 0x01c21000, "ti,davinci-wdt", NULL),
+	{}
+};
+
+const struct of_device_id enbw_cmc_bus_match_table[] = {
+	{ .compatible = "simple-bus", },
+	{ .compatible = "ti,da8xx", },
+	{ .compatible = "ti,davinci-onchipram", },
+	{ .compatible = "ti,davinci-aemif", },
+	{} /* Empty terminated list */
+};
+
+static __init void enbw_cmc_init(void)
+{
+	int ret;
+
+	of_platform_populate(NULL, enbw_cmc_bus_match_table,
+		enbw_cmc_auxdata_lookup, NULL);
+
+	ret = da850_register_edma(da850_edma_rsv);
+	if (ret)
+		pr_warning("enbw_cmc_init: edma registration failed: %d\n",
+				ret);
+
+	/*
+	 * shut down uart 0 this port is not used on the board
+	 */
+	__raw_writel(0, IO_ADDRESS(DA8XX_UART0_BASE) + 0x30);
+
+	ret = da8xx_register_rtc();
+	if (ret)
+		pr_warning("enbw_cmc_init: rtc setup failed: %d\n", ret);
+
+	ret = da850_evm_init_cpufreq();
+	if (ret)
+		pr_warning("enbw_cmc_init: cpufreq registration failed: %d\n",
+				ret);
+
+	ret = da8xx_register_cpuidle();
+	if (ret)
+		pr_warning("enbw_cmc_init: cpuidle registration failed: %d\n",
+				ret);
+
+	ret = gpio_request(ENBW_CMC_MMCSD_CD_PIN, "MMC CD\n");
+	if (ret)
+		pr_warning("enbw_cmc_init: can not open GPIO %d\n",
+				ENBW_CMC_MMCSD_CD_PIN);
+	gpio_direction_input(ENBW_CMC_MMCSD_CD_PIN);
+
+	ret = da850_register_mmcsd1(&enbw_cmc_mmc_config);
+	if (ret)
+		pr_warning("enbw_cmc_init: mmcsd1 registration failed:"
+				" %d\n", ret);
+
+	enbw_cmc_usb_init();
+}
+#else
+static __init void enbw_cmc_init(void)
+{
+	pr_err("enbw_cmc: please use OF.\n");
+	return;
+}
+#endif
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static int __init enbw_cmc_console_init(void)
+{
+	if (!machine_is_enbw_cmc())
+		return 0;
+
+	return add_preferred_console("ttyS", 2, "115200");
+}
+console_initcall(enbw_cmc_console_init);
+#endif
+
+static void __init enbw_cmc_map_io(void)
+{
+	da850_init();
+}
+
+static const char *enbw_cmc_board_compat[] __initconst = {
+	"enbw,cmc",
+	NULL
+};
+
+MACHINE_START(ENBW_CMC, "EnBW CMC")
+	.map_io		= enbw_cmc_map_io,
+	.init_irq	= davinci_init_irq,
+	.timer		= &davinci_timer,
+	.init_machine	= enbw_cmc_init,
+	.dt_compat	= enbw_cmc_board_compat,
+	.dma_zone_size	= SZ_128M,
+	.restart	= da8xx_restart,
+MACHINE_END
diff --git a/arch/arm/mach-davinci/include/mach/uncompress.h b/arch/arm/mach-davinci/include/mach/uncompress.h
index 9dc7cf9..2f21384 100644
--- a/arch/arm/mach-davinci/include/mach/uncompress.h
+++ b/arch/arm/mach-davinci/include/mach/uncompress.h
@@ -96,6 +96,7 @@  static inline void __arch_decomp_setup(unsigned long arch_id)
 		DEBUG_LL_DA8XX(davinci_da850_evm,	2);
 		DEBUG_LL_DA8XX(mityomapl138,		1);
 		DEBUG_LL_DA8XX(omapl138_hawkboard,	2);
+		DEBUG_LL_DA8XX(enbw_cmc,		2);
 
 		/* TNETV107x boards */
 		DEBUG_LL_TNETV107X(tnetv107x,		1);