diff --git a/board/Marvell/db64460/db64460.c b/board/Marvell/db64460/db64460.c
index 14e6355..a7836ed 100644
--- a/board/Marvell/db64460/db64460.c
+++ b/board/Marvell/db64460/db64460.c
@@ -34,6 +34,7 @@
 #include "../include/mv_gen_reg.h"
 #include <net.h>
 #include <netdev.h>
+#include <linux/compiler.h>
 
 #include "eth.h"
 #include "mpsc.h"
@@ -410,7 +411,7 @@ int checkboard (void)
 void debug_led (int led, int mode)
 {
 	volatile int *addr = 0;
-	int dummy;
+	__maybe_unused int dummy;
 
 	if (mode == 1) {
 		switch (led) {
diff --git a/board/Marvell/db64460/mv_eth.c b/board/Marvell/db64460/mv_eth.c
index cd9d5a4..4aefbaf 100644
--- a/board/Marvell/db64460/mv_eth.c
+++ b/board/Marvell/db64460/mv_eth.c
@@ -420,7 +420,7 @@ static int mv64460_eth_real_open (struct eth_device *dev)
 	ETH_PORT_INFO *ethernet_private;
 	struct mv64460_eth_priv *port_private;
 	unsigned int port_num;
-	u32 port_status, phy_reg_data;
+	u32 phy_reg_data;
 
 	ethernet_private = (ETH_PORT_INFO *) dev->priv;
 	/* ronen - when we update the MAC env params we only update dev->enetaddr
@@ -518,7 +518,7 @@ static int mv64460_eth_real_open (struct eth_device *dev)
 	 */
 
 	MV_REG_WRITE (MV64460_ETH_MAXIMUM_TRANSMIT_UNIT (port_num), 0);
-	port_status = MV_REG_READ (MV64460_ETH_PORT_STATUS_REG (port_num));
+	MV_REG_READ (MV64460_ETH_PORT_STATUS_REG (port_num));
 
 	/* Check Link status on phy */
 	eth_port_read_smi_reg (port_num, 1, &phy_reg_data);
@@ -636,15 +636,6 @@ static int mv64460_eth_free_rx_rings (struct eth_device *dev)
 
 int mv64460_eth_stop (struct eth_device *dev)
 {
-	ETH_PORT_INFO *ethernet_private;
-	struct mv64460_eth_priv *port_private;
-	unsigned int port_num;
-
-	ethernet_private = (ETH_PORT_INFO *) dev->priv;
-	port_private =
-		(struct mv64460_eth_priv *) ethernet_private->port_private;
-	port_num = port_private->port_num;
-
 	/* Disable all gigE address decoder */
 	MV_REG_WRITE (MV64460_ETH_BASE_ADDR_ENABLE_REG, 0x3f);
 	DP (printf ("%s Ethernet stop called ... \n", __FUNCTION__));
@@ -714,7 +705,6 @@ int mv64460_eth_xmit (struct eth_device *dev, volatile void *dataPtr,
 {
 	ETH_PORT_INFO *ethernet_private;
 	struct mv64460_eth_priv *port_private;
-	unsigned int port_num;
 	PKT_INFO pkt_info;
 	ETH_FUNC_RET_STATUS status;
 	struct net_device_stats *stats;
@@ -723,7 +713,6 @@ int mv64460_eth_xmit (struct eth_device *dev, volatile void *dataPtr,
 	ethernet_private = (ETH_PORT_INFO *) dev->priv;
 	port_private =
 		(struct mv64460_eth_priv *) ethernet_private->port_private;
-	port_num = port_private->port_num;
 
 	stats = port_private->stats;
 
@@ -799,15 +788,12 @@ int mv64460_eth_receive (struct eth_device *dev)
 {
 	ETH_PORT_INFO *ethernet_private;
 	struct mv64460_eth_priv *port_private;
-	unsigned int port_num;
 	PKT_INFO pkt_info;
 	struct net_device_stats *stats;
 
-
 	ethernet_private = (ETH_PORT_INFO *) dev->priv;
 	port_private =
 		(struct mv64460_eth_priv *) ethernet_private->port_private;
-	port_num = port_private->port_num;
 	stats = port_private->stats;
 
 	while ((eth_port_receive (ethernet_private, ETH_Q0, &pkt_info) ==
@@ -898,12 +884,10 @@ static struct net_device_stats *mv64460_eth_get_stats (struct eth_device *dev)
 {
 	ETH_PORT_INFO *ethernet_private;
 	struct mv64460_eth_priv *port_private;
-	unsigned int port_num;
 
 	ethernet_private = (ETH_PORT_INFO *) dev->priv;
 	port_private =
 		(struct mv64460_eth_priv *) ethernet_private->port_private;
-	port_num = port_private->port_num;
 
 	mv64460_eth_update_stat (dev);
 
@@ -925,13 +909,10 @@ static void mv64460_eth_update_stat (struct eth_device *dev)
 	ETH_PORT_INFO *ethernet_private;
 	struct mv64460_eth_priv *port_private;
 	struct net_device_stats *stats;
-	unsigned int port_num;
-	volatile unsigned int dummy;
 
 	ethernet_private = (ETH_PORT_INFO *) dev->priv;
 	port_private =
 		(struct mv64460_eth_priv *) ethernet_private->port_private;
-	port_num = port_private->port_num;
 	stats = port_private->stats;
 
 	/* These are false updates */
@@ -954,12 +935,12 @@ static void mv64460_eth_update_stat (struct eth_device *dev)
 	 * But the unsigned long in PowerPC and MIPS are 32bit. So the next read
 	 * is just a dummy read for proper work of the GigE port
 	 */
-	dummy = eth_read_mib_counter (ethernet_private->port_num,
+	eth_read_mib_counter (ethernet_private->port_num,
 				      ETH_MIB_GOOD_OCTETS_RECEIVED_HIGH);
 	stats->tx_bytes += (unsigned long)
 		eth_read_mib_counter (ethernet_private->port_num,
 				      ETH_MIB_GOOD_OCTETS_SENT_LOW);
-	dummy = eth_read_mib_counter (ethernet_private->port_num,
+	eth_read_mib_counter (ethernet_private->port_num,
 				      ETH_MIB_GOOD_OCTETS_SENT_HIGH);
 	stats->rx_errors += (unsigned long)
 		eth_read_mib_counter (ethernet_private->port_num,
@@ -1007,12 +988,10 @@ static void mv64460_eth_print_stat (struct eth_device *dev)
 	ETH_PORT_INFO *ethernet_private;
 	struct mv64460_eth_priv *port_private;
 	struct net_device_stats *stats;
-	unsigned int port_num;
 
 	ethernet_private = (ETH_PORT_INFO *) dev->priv;
 	port_private =
 		(struct mv64460_eth_priv *) ethernet_private->port_private;
-	port_num = port_private->port_num;
 	stats = port_private->stats;
 
 	/* These are false updates */
@@ -2064,13 +2043,11 @@ static void eth_port_init_mac_tables (ETH_PORT eth_port_num)
 static void eth_clear_mib_counters (ETH_PORT eth_port_num)
 {
 	int i;
-	unsigned int dummy;
 
 	/* Perform dummy reads from MIB counters */
 	for (i = ETH_MIB_GOOD_OCTETS_RECEIVED_LOW; i < ETH_MIB_LATE_COLLISION;
 	     i += 4)
-		dummy = MV_REG_READ ((MV64460_ETH_MIB_COUNTERS_BASE
-				      (eth_port_num) + i));
+		MV_REG_READ((MV64460_ETH_MIB_COUNTERS_BASE(eth_port_num) + i));
 
 	return;
 }
diff --git a/board/Marvell/db64460/sdram_init.c b/board/Marvell/db64460/sdram_init.c
index e328d8f..6297447 100644
--- a/board/Marvell/db64460/sdram_init.c
+++ b/board/Marvell/db64460/sdram_init.c
@@ -44,15 +44,8 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#undef	DEBUG
 #define	MAP_PCI
 
-#ifdef DEBUG
-#define DP(x) x
-#else
-#define DP(x)
-#endif
-
 int set_dfcdlInit (void);	/* setup delay line of Mv64460 */
 int mvDmaIsChannelActive (int);
 int mvDmaSetMemorySpace (ulong, ulong, ulong, ulong, ulong);
@@ -69,14 +62,12 @@ memory_map_bank (unsigned int bankNo,
 #endif
 
 
-#ifdef DEBUG
 	if (bankLength > 0) {
-		printf ("mapping bank %d at %08x - %08x\n",
+		debug("mapping bank %d at %08x - %08x\n",
 			bankNo, bankBase, bankBase + bankLength - 1);
 	} else {
-		printf ("unmapping bank %d\n", bankNo);
+		debug("unmapping bank %d\n", bankNo);
 	}
-#endif
 
 	memoryMapBank (bankNo, bankBase, bankLength);
 
@@ -276,7 +267,7 @@ return 0;
 #else
 	uchar addr = slot == 0 ? DIMM0_I2C_ADDR : DIMM1_I2C_ADDR;
 	int ret;
-	unsigned int i, j, density = 1, devicesForErrCheck = 0;
+	unsigned int i, j, density = 1;
 
 #ifdef DEBUG
 	unsigned int k;
@@ -286,17 +277,17 @@ return 0;
 	uchar supp_cal, cal_val;
 	ulong memclk, tmemclk;
 	ulong tmp;
-	uchar trp_clocks = 0, trcd_clocks, tras_clocks, trrd_clocks;
+	uchar trp_clocks = 0, tras_clocks;
 	uchar data[128];
 
 	memclk = gd->bus_clk;
 	tmemclk = 1000000000 / (memclk / 100);	/* in 10 ps units */
 
-	DP (puts ("before i2c read\n"));
+	debug("before i2c read\n");
 
 	ret = i2c_read (addr, 0, 1, data, 128);
 
-	DP (puts ("after i2c read\n"));
+	debug("after i2c read\n");
 
 	/* zero all the values */
 	memset (dimmInfo, 0, sizeof (*dimmInfo));
@@ -307,7 +298,7 @@ return 0;
 	}
 
 	if (ret) {
-		DP (printf ("No DIMM in slot %d [err = %x]\n", slot, ret));
+		debug("No DIMM in slot %d [err = %x]\n", slot, ret);
 		return 0;
 	} else
 		dimmInfo->slot = slot;	/* start to fill up dimminfo for this "slot" */
@@ -387,46 +378,46 @@ return 0;
 			dimmInfo->memoryType = (data[i] == 0x7) ? DDR : SDRAM;
 #ifdef DEBUG
 			if (dimmInfo->memoryType == 0)
-				DP (printf
+				debug
 				    ("Dram_type in slot %d is: 			SDRAM\n",
-				     dimmInfo->slot));
+				     dimmInfo->slot);
 			if (dimmInfo->memoryType == 1)
-				DP (printf
+				debug
 				    ("Dram_type in slot %d is: 			DDRAM\n",
-				     dimmInfo->slot));
+				     dimmInfo->slot);
 #endif
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 3:	/* Number Of Row Addresses */
 			dimmInfo->numOfRowAddresses = data[i];
-			DP (printf
+			debug
 			    ("Module Number of row addresses: 		%d\n",
-			     dimmInfo->numOfRowAddresses));
+			     dimmInfo->numOfRowAddresses);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 4:	/* Number Of Column Addresses */
 			dimmInfo->numOfColAddresses = data[i];
-			DP (printf
+			debug
 			    ("Module Number of col addresses: 		%d\n",
-			     dimmInfo->numOfColAddresses));
+			     dimmInfo->numOfColAddresses);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 5:	/* Number Of Module Banks */
 			dimmInfo->numOfModuleBanks = data[i];
-			DP (printf
+			debug
 			    ("Number of Banks on Mod. : 				%d\n",
-			     dimmInfo->numOfModuleBanks));
+			     dimmInfo->numOfModuleBanks);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 6:	/* Data Width */
 			dimmInfo->dataWidth = data[i];
-			DP (printf
+			debug
 			    ("Module Data Width: 				%d\n",
-			     dimmInfo->dataWidth));
+			     dimmInfo->dataWidth);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -434,33 +425,33 @@ return 0;
 			switch (data[i]) {
 			case 0x0:
 				dimmInfo->voltageInterface = TTL_5V_TOLERANT;
-				DP (printf
-				    ("Module is 					TTL_5V_TOLERANT\n"));
+				debug
+				    ("Module is 					TTL_5V_TOLERANT\n");
 				break;
 			case 0x1:
 				dimmInfo->voltageInterface = LVTTL;
-				DP (printf
-				    ("Module is 					LVTTL\n"));
+				debug
+				    ("Module is 					LVTTL\n");
 				break;
 			case 0x2:
 				dimmInfo->voltageInterface = HSTL_1_5V;
-				DP (printf
-				    ("Module is 					TTL_5V_TOLERANT\n"));
+				debug
+				    ("Module is 					TTL_5V_TOLERANT\n");
 				break;
 			case 0x3:
 				dimmInfo->voltageInterface = SSTL_3_3V;
-				DP (printf
-				    ("Module is 					HSTL_1_5V\n"));
+				debug
+				    ("Module is 					HSTL_1_5V\n");
 				break;
 			case 0x4:
 				dimmInfo->voltageInterface = SSTL_2_5V;
-				DP (printf
-				    ("Module is 					SSTL_2_5V\n"));
+				debug
+				    ("Module is 					SSTL_2_5V\n");
 				break;
 			default:
 				dimmInfo->voltageInterface = VOLTAGE_UNKNOWN;
-				DP (printf
-				    ("Module is 					VOLTAGE_UNKNOWN\n"));
+				debug
+				    ("Module is 					VOLTAGE_UNKNOWN\n");
 				break;
 			}
 			break;
@@ -479,9 +470,9 @@ return 0;
 				leftOfPoint;
 			dimmInfo->minimumCycleTimeAtMaxCasLatancy_RoP =
 				rightOfPoint;
-			DP (printf
+			debug
 			    ("Minimum Cycle Time At Max CasLatancy: 		%d.%d [ns]\n",
-			     leftOfPoint, rightOfPoint));
+			     leftOfPoint, rightOfPoint);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -494,49 +485,49 @@ return 0;
 			rightOfPoint = time_tmp % div;
 			dimmInfo->clockToDataOut_LoP = leftOfPoint;
 			dimmInfo->clockToDataOut_RoP = rightOfPoint;
-			DP (printf ("Clock To Data Out: 				%d.%2d [ns]\n", leftOfPoint, rightOfPoint));	/*dimmInfo->clockToDataOut */
+			debug("Clock To Data Out: 				%d.%2d [ns]\n", leftOfPoint, rightOfPoint);	/*dimmInfo->clockToDataOut */
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 /*#ifdef CONFIG_ECC */
 		case 11:	/* Error Check Type */
 			dimmInfo->errorCheckType = data[i];
-			DP (printf
+			debug
 			    ("Error Check Type (0=NONE): 			%d\n",
-			     dimmInfo->errorCheckType));
+			     dimmInfo->errorCheckType);
 			break;
 /* #endif */
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 12:	/* Refresh Interval */
 			dimmInfo->RefreshInterval = data[i];
-			DP (printf
+			debug
 			    ("RefreshInterval (80= Self refresh Normal, 15.625us) : %x\n",
-			     dimmInfo->RefreshInterval));
+			     dimmInfo->RefreshInterval);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 13:	/* Sdram Width */
 			dimmInfo->sdramWidth = data[i];
-			DP (printf
+			debug
 			    ("Sdram Width: 					%d\n",
-			     dimmInfo->sdramWidth));
+			     dimmInfo->sdramWidth);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 14:	/* Error Check Data Width */
 			dimmInfo->errorCheckDataWidth = data[i];
-			DP (printf
+			debug
 			    ("Error Check Data Width: 			%d\n",
-			     dimmInfo->errorCheckDataWidth));
+			     dimmInfo->errorCheckDataWidth);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 15:	/* Minimum Clock Delay */
 			dimmInfo->minClkDelay = data[i];
-			DP (printf
+			debug
 			    ("Minimum Clock Delay: 				%d\n",
-			     dimmInfo->minClkDelay));
+			     dimmInfo->minClkDelay);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -552,26 +543,26 @@ return 0;
 
 			dimmInfo->burstLengthSupported = data[i];
 #ifdef DEBUG
-			DP (printf
-			    ("Burst Length Supported: 			"));
+			debug
+			    ("Burst Length Supported: 			");
 			if (dimmInfo->burstLengthSupported & 0x01)
-				DP (printf ("1, "));
+				debug("1, ");
 			if (dimmInfo->burstLengthSupported & 0x02)
-				DP (printf ("2, "));
+				debug("2, ");
 			if (dimmInfo->burstLengthSupported & 0x04)
-				DP (printf ("4, "));
+				debug("4, ");
 			if (dimmInfo->burstLengthSupported & 0x08)
-				DP (printf ("8, "));
-			DP (printf (" Bit \n"));
+				debug("8, ");
+			debug(" Bit \n");
 #endif
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 17:	/* Number Of Banks On Each Device */
 			dimmInfo->numOfBanksOnEachDevice = data[i];
-			DP (printf
+			debug
 			    ("Number Of Banks On Each Chip: 			%d\n",
-			     dimmInfo->numOfBanksOnEachDevice));
+			     dimmInfo->numOfBanksOnEachDevice);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -591,34 +582,34 @@ return 0;
 			 ********************************************************/
 			dimmInfo->suportedCasLatencies = data[i];
 #ifdef DEBUG
-			DP (printf
-			    ("Suported Cas Latencies: (CL) 			"));
+			debug
+			    ("Suported Cas Latencies: (CL) 			");
 			if (dimmInfo->memoryType == 0) {	/* SDRAM */
 				for (k = 0; k <= 7; k++) {
 					if (dimmInfo->
 					    suportedCasLatencies & (1 << k))
-						DP (printf
+						debug
 						    ("%d, 			",
-						     k + 1));
+						     k + 1);
 				}
 
 			} else {	/* DDR-RAM */
 
 				if (dimmInfo->suportedCasLatencies & 1)
-					DP (printf ("1, "));
+					debug("1, ");
 				if (dimmInfo->suportedCasLatencies & 2)
-					DP (printf ("1.5, "));
+					debug("1.5, ");
 				if (dimmInfo->suportedCasLatencies & 4)
-					DP (printf ("2, "));
+					debug("2, ");
 				if (dimmInfo->suportedCasLatencies & 8)
-					DP (printf ("2.5, "));
+					debug("2.5, ");
 				if (dimmInfo->suportedCasLatencies & 16)
-					DP (printf ("3, "));
+					debug("3, ");
 				if (dimmInfo->suportedCasLatencies & 32)
-					DP (printf ("3.5, "));
+					debug("3.5, ");
 
 			}
-			DP (printf ("\n"));
+			debug("\n");
 #endif
 			/* Calculating MAX CAS latency */
 			for (j = 7; j > 0; j--) {
@@ -630,8 +621,8 @@ return 0;
 						/* CAS latency 1, 1.5, 2, 2.5, 3, 3.5 */
 						switch (j) {
 						case 7:
-							DP (printf
-							    ("Max. Cas Latencies (DDR): 			ERROR !!!\n"));
+							debug
+							    ("Max. Cas Latencies (DDR): 			ERROR !!!\n");
 							dimmInfo->
 								maxClSupported_DDR
 								=
@@ -639,8 +630,8 @@ return 0;
 							hang ();
 							break;
 						case 6:
-							DP (printf
-							    ("Max. Cas Latencies (DDR): 			ERROR !!!\n"));
+							debug
+							    ("Max. Cas Latencies (DDR): 			ERROR !!!\n");
 							dimmInfo->
 								maxClSupported_DDR
 								=
@@ -648,36 +639,36 @@ return 0;
 							hang ();
 							break;
 						case 5:
-							DP (printf
-							    ("Max. Cas Latencies (DDR): 			3.5 clk's\n"));
+							debug
+							    ("Max. Cas Latencies (DDR): 			3.5 clk's\n");
 							dimmInfo->
 								maxClSupported_DDR
 								= DDR_CL_3_5;
 							break;
 						case 4:
-							DP (printf
-							    ("Max. Cas Latencies (DDR): 			3 clk's \n"));
+							debug
+							    ("Max. Cas Latencies (DDR): 			3 clk's \n");
 							dimmInfo->
 								maxClSupported_DDR
 								= DDR_CL_3;
 							break;
 						case 3:
-							DP (printf
-							    ("Max. Cas Latencies (DDR): 			2.5 clk's \n"));
+							debug
+							    ("Max. Cas Latencies (DDR): 			2.5 clk's \n");
 							dimmInfo->
 								maxClSupported_DDR
 								= DDR_CL_2_5;
 							break;
 						case 2:
-							DP (printf
-							    ("Max. Cas Latencies (DDR): 			2 clk's \n"));
+							debug
+							    ("Max. Cas Latencies (DDR): 			2 clk's \n");
 							dimmInfo->
 								maxClSupported_DDR
 								= DDR_CL_2;
 							break;
 						case 1:
-							DP (printf
-							    ("Max. Cas Latencies (DDR): 			1.5 clk's \n"));
+							debug
+							    ("Max. Cas Latencies (DDR): 			1.5 clk's \n");
 							dimmInfo->
 								maxClSupported_DDR
 								= DDR_CL_1_5;
@@ -707,8 +698,8 @@ return 0;
 								dimmInfo->
 								maxClSupported_DDR
 								>> 1;
-							DP (printf
-							    ("*** Change actual Cas Latencies cause of minimumCycleTime n"));
+							debug
+							    ("*** Change actual Cas Latencies cause of minimumCycleTime n");
 						}
 						/* ronen - checkif the Dimm frequency compared to the Sysclock. */
 						if ((dimmInfo->
@@ -744,32 +735,32 @@ return 0;
 							dimmInfo->
 								maxCASlatencySupported_RoP
 								= 0;
-						DP (printf
+						debug
 						    ("Max. Cas Latencies (DDR LoP.RoP Notation): 	%d.%d \n",
 						     dimmInfo->
 						     maxCASlatencySupported_LoP,
 						     dimmInfo->
-						     maxCASlatencySupported_RoP));
+						     maxCASlatencySupported_RoP);
 						break;
 					case SDRAM:
 						/* CAS latency 1, 2, 3, 4, 5, 6, 7 */
 						dimmInfo->maxClSupported_SD = j;	/*  Cas Latency DDR-RAM Coded                   */
-						DP (printf
+						debug
 						    ("Max. Cas Latencies (SD): %d\n",
 						     dimmInfo->
-						     maxClSupported_SD));
+						     maxClSupported_SD);
 						dimmInfo->
 							maxCASlatencySupported_LoP
 							= j;
 						dimmInfo->
 							maxCASlatencySupported_RoP
 							= 0;
-						DP (printf
+						debug
 						    ("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n",
 						     dimmInfo->
 						     maxCASlatencySupported_LoP,
 						     dimmInfo->
-						     maxCASlatencySupported_RoP));
+						     maxCASlatencySupported_RoP);
 						break;
 					}
 					break;
@@ -779,7 +770,7 @@ return 0;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 21:	/* Buffered Address And Control Inputs */
-			DP (printf ("\nModul Attributes (SPD Byte 21): \n"));
+			debug("\nModul Attributes (SPD Byte 21): \n");
 			dimmInfo->bufferedAddrAndControlInputs =
 				data[i] & BIT0;
 			dimmInfo->registeredAddrAndControlInputs =
@@ -794,60 +785,60 @@ return 0;
 				(data[i] & BIT6) >> 6;
 #ifdef DEBUG
 			if (dimmInfo->bufferedAddrAndControlInputs == 1)
-				DP (printf
-				    (" - Buffered Address/Control Input:		Yes \n"));
+				debug
+				    (" - Buffered Address/Control Input:		Yes \n");
 			else
-				DP (printf
-				    (" - Buffered Address/Control Input:		No \n"));
+				debug
+				    (" - Buffered Address/Control Input:		No \n");
 
 			if (dimmInfo->registeredAddrAndControlInputs == 1)
-				DP (printf
-				    (" - Registered Address/Control Input:		Yes \n"));
+				debug
+				    (" - Registered Address/Control Input:		Yes \n");
 			else
-				DP (printf
-				    (" - Registered Address/Control Input:		No \n"));
+				debug
+				    (" - Registered Address/Control Input:		No \n");
 
 			if (dimmInfo->onCardPLL == 1)
-				DP (printf
-				    (" - On-Card PLL (clock):				Yes \n"));
+				debug
+				    (" - On-Card PLL (clock):				Yes \n");
 			else
-				DP (printf
-				    (" - On-Card PLL (clock):				No \n"));
+				debug
+				    (" - On-Card PLL (clock):				No \n");
 
 			if (dimmInfo->bufferedDQMBinputs == 1)
-				DP (printf
-				    (" - Bufferd DQMB Inputs:				Yes \n"));
+				debug
+				    (" - Bufferd DQMB Inputs:				Yes \n");
 			else
-				DP (printf
-				    (" - Bufferd DQMB Inputs:				No \n"));
+				debug
+				    (" - Bufferd DQMB Inputs:				No \n");
 
 			if (dimmInfo->registeredDQMBinputs == 1)
-				DP (printf
-				    (" - Registered DQMB Inputs:			Yes \n"));
+				debug
+				    (" - Registered DQMB Inputs:			Yes \n");
 			else
-				DP (printf
-				    (" - Registered DQMB Inputs:			No \n"));
+				debug
+				    (" - Registered DQMB Inputs:			No \n");
 
 			if (dimmInfo->differentialClockInput == 1)
-				DP (printf
-				    (" - Differential Clock Input:			Yes \n"));
+				debug
+				    (" - Differential Clock Input:			Yes \n");
 			else
-				DP (printf
-				    (" - Differential Clock Input:			No \n"));
+				debug
+				    (" - Differential Clock Input:			No \n");
 
 			if (dimmInfo->redundantRowAddressing == 1)
-				DP (printf
-				    (" - redundant Row Addressing:			Yes \n"));
+				debug
+				    (" - redundant Row Addressing:			Yes \n");
 			else
-				DP (printf
-				    (" - redundant Row Addressing:			No \n"));
+				debug
+				    (" - redundant Row Addressing:			No \n");
 
 #endif
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 22:	/* Suported AutoPreCharge */
-			DP (printf ("\nModul Attributes (SPD Byte 22): \n"));
+			debug("\nModul Attributes (SPD Byte 22): \n");
 			dimmInfo->suportedEarlyRasPreCharge = data[i] & BIT0;
 			dimmInfo->suportedAutoPreCharge =
 				(data[i] & BIT1) >> 1;
@@ -861,46 +852,46 @@ return 0;
 				(data[i] & BIT5) >> 5;
 #ifdef DEBUG
 			if (dimmInfo->suportedEarlyRasPreCharge == 1)
-				DP (printf
-				    (" - Early Ras Precharge:			Yes \n"));
+				debug
+				    (" - Early Ras Precharge:			Yes \n");
 			else
-				DP (printf
-				    (" -  Early Ras Precharge:			No \n"));
+				debug
+				    (" -  Early Ras Precharge:			No \n");
 
 			if (dimmInfo->suportedAutoPreCharge == 1)
-				DP (printf
-				    (" - AutoPreCharge:				Yes \n"));
+				debug
+				    (" - AutoPreCharge:				Yes \n");
 			else
-				DP (printf
-				    (" -  AutoPreCharge:				No \n"));
+				debug
+				    (" -  AutoPreCharge:				No \n");
 
 			if (dimmInfo->suportedPreChargeAll == 1)
-				DP (printf
-				    (" - Precharge All:				Yes \n"));
+				debug
+				    (" - Precharge All:				Yes \n");
 			else
-				DP (printf
-				    (" -  Precharge All:				No \n"));
+				debug
+				    (" -  Precharge All:				No \n");
 
 			if (dimmInfo->suportedWrite1ReadBurst == 1)
-				DP (printf
-				    (" - Write 1/ReadBurst:				Yes \n"));
+				debug
+				    (" - Write 1/ReadBurst:				Yes \n");
 			else
-				DP (printf
-				    (" -  Write 1/ReadBurst:				No \n"));
+				debug
+				    (" -  Write 1/ReadBurst:				No \n");
 
 			if (dimmInfo->suported5PercentLowVCC == 1)
-				DP (printf
-				    (" - lower VCC tolerance:			5 Percent \n"));
+				debug
+				    (" - lower VCC tolerance:			5 Percent \n");
 			else
-				DP (printf
-				    ("  - lower VCC tolerance:			10 Percent \n"));
+				debug
+				    ("  - lower VCC tolerance:			10 Percent \n");
 
 			if (dimmInfo->suported5PercentUpperVCC == 1)
-				DP (printf
-				    (" - upper VCC tolerance:			5 Percent \n"));
+				debug
+				    (" - upper VCC tolerance:			5 Percent \n");
 			else
-				DP (printf
-				    (" -  upper VCC tolerance:			10 Percent \n"));
+				debug
+				    (" -  upper VCC tolerance:			10 Percent \n");
 
 #endif
 			break;
@@ -919,7 +910,7 @@ return 0;
 				leftOfPoint;
 			dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus1_RoP =
 				rightOfPoint;
-			DP (printf ("Minimum Cycle Time At 2nd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", leftOfPoint, rightOfPoint));	/*dimmInfo->minimumCycleTimeAtMaxCasLatancy */
+			debug("Minimum Cycle Time At 2nd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", leftOfPoint, rightOfPoint);	/*dimmInfo->minimumCycleTimeAtMaxCasLatancy */
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -932,9 +923,9 @@ return 0;
 			rightOfPoint = time_tmp % div;
 			dimmInfo->clockToDataOutMinus1_LoP = leftOfPoint;
 			dimmInfo->clockToDataOutMinus1_RoP = rightOfPoint;
-			DP (printf
+			debug
 			    ("Clock To Data Out (2nd CL value): 		%d.%2d [ns]\n",
-			     leftOfPoint, rightOfPoint));
+			     leftOfPoint, rightOfPoint);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -951,7 +942,7 @@ return 0;
 				leftOfPoint;
 			dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus2_RoP =
 				rightOfPoint;
-			DP (printf ("Minimum Cycle Time At 3rd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", leftOfPoint, rightOfPoint));	/*dimmInfo->minimumCycleTimeAtMaxCasLatancy */
+			debug("Minimum Cycle Time At 3rd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", leftOfPoint, rightOfPoint);	/*dimmInfo->minimumCycleTimeAtMaxCasLatancy */
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -964,9 +955,9 @@ return 0;
 			rightOfPoint = time_tmp % div;
 			dimmInfo->clockToDataOutMinus2_LoP = leftOfPoint;
 			dimmInfo->clockToDataOutMinus2_RoP = rightOfPoint;
-			DP (printf
+			debug
 			    ("Clock To Data Out (3rd CL value): 		%d.%2d [ns]\n",
-			     leftOfPoint, rightOfPoint));
+			     leftOfPoint, rightOfPoint);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -983,12 +974,12 @@ return 0;
 			trp_clocks =
 				(dimmInfo->minRowPrechargeTime +
 				 (tmemclk - 1)) / tmemclk;
-			DP (printf
+			debug
 			    ("*** 1 clock cycle = %ld  10ps intervalls = %ld.%ld ns****\n",
-			     tmemclk, tmemclk / 100, tmemclk % 100));
-			DP (printf
+			     tmemclk, tmemclk / 100, tmemclk % 100);
+			debug
 			    ("Minimum Row Precharge Time [ns]: 		%d.%2d = in Clk cycles %d\n",
-			     leftOfPoint, rightOfPoint, trp_clocks));
+			     leftOfPoint, rightOfPoint, trp_clocks);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -1002,12 +993,9 @@ return 0;
 			rightOfPoint = (data[i] & maskRightOfPoint) * 25;
 
 			dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint);	/* measured in 100ns Intervals */
-			trrd_clocks =
-				(dimmInfo->minRowActiveRowActiveDelay +
-				 (tmemclk - 1)) / tmemclk;
-			DP (printf
+			debug
 			    ("Minimum Row Active -To- Row Active Delay [ns]: 	%d.%2d = in Clk cycles %d\n",
-			     leftOfPoint, rightOfPoint, trp_clocks));
+			     leftOfPoint, rightOfPoint, trp_clocks);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -1021,12 +1009,9 @@ return 0;
 			rightOfPoint = (data[i] & maskRightOfPoint) * 25;
 
 			dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint);	/* measured in 100ns Intervals */
-			trcd_clocks =
-				(dimmInfo->minRowActiveRowActiveDelay +
-				 (tmemclk - 1)) / tmemclk;
-			DP (printf
+			debug
 			    ("Minimum Ras-To-Cas Delay [ns]: 			%d.%2d = in Clk cycles %d\n",
-			     leftOfPoint, rightOfPoint, trp_clocks));
+			     leftOfPoint, rightOfPoint, trp_clocks);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -1035,41 +1020,41 @@ return 0;
 			tras_clocks =
 				(NSto10PS (data[i]) +
 				 (tmemclk - 1)) / tmemclk;
-			DP (printf
+			debug
 			    ("Minimum Ras Pulse Width [ns]: 			%d = in Clk cycles %d\n",
-			     dimmInfo->minRasPulseWidth, tras_clocks));
+			     dimmInfo->minRasPulseWidth, tras_clocks);
 
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
 		case 31:	/* Module Bank Density */
 			dimmInfo->moduleBankDensity = data[i];
-			DP (printf
+			debug
 			    ("Module Bank Density: 				%d\n",
-			     dimmInfo->moduleBankDensity));
+			     dimmInfo->moduleBankDensity);
 #ifdef DEBUG
-			DP (printf
-			    ("*** Offered Densities (more than 1 = Multisize-Module): "));
+			debug
+			    ("*** Offered Densities (more than 1 = Multisize-Module): ");
 			{
 				if (dimmInfo->moduleBankDensity & 1)
-					DP (printf ("4MB, "));
+					debug("4MB, ");
 				if (dimmInfo->moduleBankDensity & 2)
-					DP (printf ("8MB, "));
+					debug("8MB, ");
 				if (dimmInfo->moduleBankDensity & 4)
-					DP (printf ("16MB, "));
+					debug("16MB, ");
 				if (dimmInfo->moduleBankDensity & 8)
-					DP (printf ("32MB, "));
+					debug("32MB, ");
 				if (dimmInfo->moduleBankDensity & 16)
-					DP (printf ("64MB, "));
+					debug("64MB, ");
 				if (dimmInfo->moduleBankDensity & 32)
-					DP (printf ("128MB, "));
+					debug("128MB, ");
 				if ((dimmInfo->moduleBankDensity & 64)
 				    || (dimmInfo->moduleBankDensity & 128)) {
-					DP (printf ("ERROR, "));
+					debug("ERROR, ");
 					hang ();
 				}
 			}
-			DP (printf ("\n"));
+			debug("\n");
 #endif
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
@@ -1095,9 +1080,9 @@ return 0;
 			}
 			dimmInfo->addrAndCommandSetupTime =
 				(leftOfPoint * 100 + rightOfPoint) * sign;
-			DP (printf
+			debug
 			    ("Address And Command Setup Time [ns]: 		%d.%d\n",
-			     sign * leftOfPoint, rightOfPoint));
+			     sign * leftOfPoint, rightOfPoint);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -1122,9 +1107,9 @@ return 0;
 			}
 			dimmInfo->addrAndCommandHoldTime =
 				(leftOfPoint * 100 + rightOfPoint) * sign;
-			DP (printf
+			debug
 			    ("Address And Command Hold Time [ns]: 		%d.%d\n",
-			     sign * leftOfPoint, rightOfPoint));
+			     sign * leftOfPoint, rightOfPoint);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -1149,9 +1134,9 @@ return 0;
 			}
 			dimmInfo->dataInputSetupTime =
 				(leftOfPoint * 100 + rightOfPoint) * sign;
-			DP (printf
+			debug
 			    ("Data Input Setup Time [ns]: 			%d.%d\n",
-			     sign * leftOfPoint, rightOfPoint));
+			     sign * leftOfPoint, rightOfPoint);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 
@@ -1176,9 +1161,9 @@ return 0;
 			}
 			dimmInfo->dataInputHoldTime =
 				(leftOfPoint * 100 + rightOfPoint) * sign;
-			DP (printf
+			debug
 			    ("Data Input Hold Time [ns]: 			%d.%d\n\n",
-			     sign * leftOfPoint, rightOfPoint));
+			     sign * leftOfPoint, rightOfPoint);
 			break;
 /*------------------------------------------------------------------------------------------------------------------------------*/
 		}
@@ -1194,8 +1179,6 @@ return 0;
 	dimmInfo->numberOfDevices =
 		(dimmInfo->dataWidth / dimmInfo->sdramWidth) *
 		dimmInfo->numOfModuleBanks;
-	devicesForErrCheck =
-		(dimmInfo->dataWidth - 64) / dimmInfo->sdramWidth;
 	if ((dimmInfo->errorCheckType == 0x1)
 	    || (dimmInfo->errorCheckType == 0x2)
 	    || (dimmInfo->errorCheckType == 0x3)) {
@@ -1217,7 +1200,7 @@ return 0;
 	tmp *= dimmInfo->sdramWidth;
 	tmp = tmp >> 24;	/* div by 0x4000000 (64M)       */
 	dimmInfo->drb_size = (uchar) tmp;
-	DP (printf ("Module DRB size (n*64Mbit): %d\n", dimmInfo->drb_size));
+	debug("Module DRB size (n*64Mbit): %d\n", dimmInfo->drb_size);
 
 	/* try a CAS latency of 3 first... */
 
@@ -1236,11 +1219,11 @@ return 0;
 			cal_val = 2;
 	}
 
-	DP (printf ("cal_val = %d\n", cal_val));
+	debug("cal_val = %d\n", cal_val);
 
 	/* bummer, did't work... */
 	if (cal_val == 0) {
-		DP (printf ("Couldn't find a good CAS latency\n"));
+		debug("Couldn't find a good CAS latency\n");
 		hang ();
 		return 0;
 	}
@@ -1271,13 +1254,13 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 
 	/* delay line */
 	set_dfcdlInit ();	/* may be its not needed */
-	DP (printf ("Delay line set done\n"));
+	debug("Delay line set done\n");
 
 	/* set SDRAM mode NOP */ /* To_do check it */
 	GT_REG_WRITE (SDRAM_OPERATION, 0x5);
 	while (GTREGREAD (SDRAM_OPERATION) != 0) {
-		DP (printf
-		    ("\n*** SDRAM_OPERATION 1418: Module still busy ... please wait... ***\n"));
+		debug
+		    ("\n*** SDRAM_OPERATION 1418: Module still busy ... please wait... ***\n");
 	}
 
 	/* SDRAM configuration */
@@ -1328,12 +1311,12 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 		hang ();
 		break;
 	}
-	DP (printf ("calculated refresh interval %0x\n", sdram_config_reg));
+	debug("calculated refresh interval %0x\n", sdram_config_reg);
 
 	/* make sure the refresh value is only 14 bits */
 	if (sdram_config_reg > 0x1fff)
 		sdram_config_reg = 0x1fff;
-	DP (printf ("adjusted refresh interval %0x\n", sdram_config_reg));
+	debug("adjusted refresh interval %0x\n", sdram_config_reg);
 
 	/* we want physical bank interleaving and */
 	/* virtual bank interleaving enabled so do nothing */
@@ -1343,30 +1326,30 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 	if (info->registeredAddrAndControlInputs == 1) {
 		/* it's registered DRAM, so set the reg. DRAM bit */
 		sdram_config_reg = sdram_config_reg | BIT17;
-		DP (printf ("Enabling registered DRAM bit\n"));
+		debug("Enabling registered DRAM bit\n");
 	}
 	/* turn on DRAM ECC? */
 #ifdef CONFIG_MV64460_ECC
 	if (info->errorCheckType == 0x2) {
 		/* DRAM has ECC, so turn it on */
 		sdram_config_reg = sdram_config_reg | BIT18;
-		DP (printf ("Enabling ECC\n"));
+		debug("Enabling ECC\n");
 	}
 #endif
 	/* set the data DQS pin configuration */
 	switch (info->sdramWidth) {
 	case 0x4:		/* memory is x4 */
 		sdram_config_reg = sdram_config_reg | BIT20 | BIT21;
-		DP (printf ("Data DQS pins set for 16 pins\n"));
+		debug("Data DQS pins set for 16 pins\n");
 		break;
 	case 0x8:		/* memory is x8 or x16 */
 	case 0x10:
 		sdram_config_reg = sdram_config_reg | BIT21;
-		DP (printf ("Data DQS pins set for 8 pins\n"));
+		debug("Data DQS pins set for 8 pins\n");
 		break;
 	case 0x20:		/* memory is x32 */
 		/* both bits are cleared for x32 so nothing to do */
-		DP (printf ("Data DQS pins set for 2 pins\n"));
+		debug("Data DQS pins set for 2 pins\n");
 		break;
 	default:		/* memory width unsupported */
 		printf ("DRAM chip width is unknown!\n");
@@ -1392,21 +1375,21 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 
 	/* write the value into the SDRAM configuration register */
 	GT_REG_WRITE (SDRAM_CONFIG, sdram_config_reg);
-	DP (printf ("sdram_conf 0x1400: %08x\n", GTREGREAD (SDRAM_CONFIG)));
+	debug("sdram_conf 0x1400: %08x\n", GTREGREAD (SDRAM_CONFIG));
 
 	/* SDRAM open pages control keep open as much as I can */
 	GT_REG_WRITE (SDRAM_OPEN_PAGES_CONTROL, 0x0);
-	DP (printf
+	debug
 	    ("sdram_open_pages_controll 0x1414: %08x\n",
-	     GTREGREAD (SDRAM_OPEN_PAGES_CONTROL)));
+	     GTREGREAD (SDRAM_OPEN_PAGES_CONTROL));
 
 	/* SDRAM D_UNIT_CONTROL_LOW 0x1404 */
 	tmp = (GTREGREAD (D_UNIT_CONTROL_LOW) & 0x01);	/* Clock Domain Sync from power on reset */
 	if (tmp == 0)
-		DP (printf ("Core Signals are sync (by HW-Setting)!!!\n"));
+		debug("Core Signals are sync (by HW-Setting)!!!\n");
 	else
-		DP (printf
-		    ("Core Signals syncs. are bypassed (by HW-Setting)!!!\n"));
+		debug
+		    ("Core Signals syncs. are bypassed (by HW-Setting)!!!\n");
 
 	/* SDRAM set CAS Latency according to SPD information */
 	switch (info->memoryType) {
@@ -1419,7 +1402,7 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 		/* Calculate the settings for SDRAM mode and Dunit control low registers */
 		/* Values set according to technical bulletin TB-92 rev. c */
 	case DDR:
-		DP (printf ("### SET-CL for DDR-RAM\n"));
+		debug("### SET-CL for DDR-RAM\n");
 		/* ronen db64460 - change the tmp_dunit_control_low setting!!! */
 		switch (info->maxClSupported_DDR) {
 		case DDR_CL_3:
@@ -1429,9 +1412,9 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 					tmp_dunit_control_low = 0x05110051;
 				else
 					tmp_dunit_control_low = 0x24110051;
-				DP (printf
+				debug
 				    ("Max. CL is 3 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
-				     tmp_sdram_mode, tmp_dunit_control_low));
+				     tmp_sdram_mode, tmp_dunit_control_low);
 				printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n");
 			} else {	/* clk sync. bypassed   */
 
@@ -1439,9 +1422,9 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 					tmp_dunit_control_low = 0xC5000540;
 				else
 					tmp_dunit_control_low = 0xC4000540;
-				DP (printf
+				debug
 				    ("Max. CL is 3 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
-				     tmp_sdram_mode, tmp_dunit_control_low));
+				     tmp_sdram_mode, tmp_dunit_control_low);
 			}
 			break;
 		case DDR_CL_2_5:
@@ -1451,9 +1434,9 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 					tmp_dunit_control_low = 0x25110051;
 				else
 					tmp_dunit_control_low = 0x24110051;
-				DP (printf
+				debug
 				    ("Max. CL is 2.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
-				     tmp_sdram_mode, tmp_dunit_control_low));
+				     tmp_sdram_mode, tmp_dunit_control_low);
 				printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n");
 			} else {	/* clk sync. bypassed   */
 
@@ -1464,9 +1447,9 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 					/* hang();1 */
 				} else
 					tmp_dunit_control_low = 0xC4000540;
-				DP (printf
+				debug
 				    ("Max. CL is 2.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
-				     tmp_sdram_mode, tmp_dunit_control_low));
+				     tmp_sdram_mode, tmp_dunit_control_low);
 			}
 			break;
 		case DDR_CL_2:
@@ -1476,9 +1459,9 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 					tmp_dunit_control_low = 0x04110051;
 				else
 					tmp_dunit_control_low = 0x03110051;
-				DP (printf
+				debug
 				    ("Max. CL is 2 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
-				     tmp_sdram_mode, tmp_dunit_control_low));
+				     tmp_sdram_mode, tmp_dunit_control_low);
 				printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n");
 			} else {	/* clk sync. bypassed   */
 
@@ -1489,9 +1472,9 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 					tmp_dunit_control_low = 0xC4000540;
 				} else
 					tmp_dunit_control_low = 0xC3000540;;
-				DP (printf
+				debug
 				    ("Max. CL is 2 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
-				     tmp_sdram_mode, tmp_dunit_control_low));
+				     tmp_sdram_mode, tmp_dunit_control_low);
 			}
 			break;
 		case DDR_CL_1_5:
@@ -1501,9 +1484,9 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 					tmp_dunit_control_low = 0x24110051;
 				else
 					tmp_dunit_control_low = 0x23110051;
-				DP (printf
+				debug
 				    ("Max. CL is 1.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
-				     tmp_sdram_mode, tmp_dunit_control_low));
+				     tmp_sdram_mode, tmp_dunit_control_low);
 				printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n");
 			} else {	/* clk sync. bypassed   */
 
@@ -1514,9 +1497,9 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 					tmp_dunit_control_low = 0xC4000540;
 				} else
 					tmp_dunit_control_low = 0xC3000540;
-				DP (printf
+				debug
 				    ("Max. CL is 1.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
-				     tmp_sdram_mode, tmp_dunit_control_low));
+				     tmp_sdram_mode, tmp_dunit_control_low);
 			}
 			break;
 
@@ -1536,8 +1519,8 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 	/* set SDRAM mode SetCommand 0x1418 */
 	GT_REG_WRITE (SDRAM_OPERATION, 0x3);
 	while (GTREGREAD (SDRAM_OPERATION) != 0) {
-		DP (printf
-		    ("\n*** SDRAM_OPERATION 0x1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+		debug
+		    ("\n*** SDRAM_OPERATION 0x1418 after SDRAM_MODE: Module still busy ... please wait... ***\n");
 	}
 
 	/* SDRAM D_UNIT_CONTROL_LOW 0x1404 */
@@ -1546,8 +1529,8 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 	/* set SDRAM mode SetCommand 0x1418 */
 	GT_REG_WRITE (SDRAM_OPERATION, 0x3);
 	while (GTREGREAD (SDRAM_OPERATION) != 0) {
-		DP (printf
-		    ("\n*** SDRAM_OPERATION 1418 after D_UNIT_CONTROL_LOW: Module still busy ... please wait... ***\n"));
+		debug
+		    ("\n*** SDRAM_OPERATION 1418 after D_UNIT_CONTROL_LOW: Module still busy ... please wait... ***\n");
 	}
 
 /*------------------------------------------------------------------------------ */
@@ -1557,29 +1540,29 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 	/* program this with the default value */
 	tmp = 0x02;		/* power-up default address select decoding value */
 
-	DP (printf ("drb_size (n*64Mbit): %d\n", info->drb_size));
+	debug("drb_size (n*64Mbit): %d\n", info->drb_size);
 /* figure out the DRAM chip size */
 	sdram_chip_size =
 		(1 << (info->numOfRowAddresses + info->numOfColAddresses));
 	sdram_chip_size *= info->sdramWidth;
 	sdram_chip_size *= 4;
-	DP (printf ("computed sdram chip size is %#lx\n", sdram_chip_size));
+	debug("computed sdram chip size is %#lx\n", sdram_chip_size);
 	/* divide sdram chip size by 64 Mbits */
 	sdram_chip_size = sdram_chip_size / 0x4000000;
 	switch (sdram_chip_size) {
 	case 1:		/* 64 Mbit */
 	case 2:		/* 128 Mbit */
-		DP (printf ("RAM-Device_size 64Mbit or 128Mbit)\n"));
+		debug("RAM-Device_size 64Mbit or 128Mbit)\n");
 		tmp |= (0x00 << 4);
 		break;
 	case 4:		/* 256 Mbit */
 	case 8:		/* 512 Mbit */
-		DP (printf ("RAM-Device_size 256Mbit or 512Mbit)\n"));
+		debug("RAM-Device_size 256Mbit or 512Mbit)\n");
 		tmp |= (0x01 << 4);
 		break;
 	case 16:		/* 1 Gbit */
 	case 32:		/* 2 Gbit */
-		DP (printf ("RAM-Device_size 1Gbit or 2Gbit)\n"));
+		debug("RAM-Device_size 1Gbit or 2Gbit)\n");
 		tmp |= (0x02 << 4);
 		break;
 	default:
@@ -1590,15 +1573,15 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 
 	/* SDRAM address control */
 	GT_REG_WRITE (SDRAM_ADDR_CONTROL, tmp);
-	DP (printf
+	debug
 	    ("setting up sdram address control (0x1410) with: %08lx \n",
-	     tmp));
+	     tmp);
 
 /* ------------------------------------------------------------------------------ */
 /* same settings for registerd & non-registerd DDR SDRAM */
-	DP (printf
+	debug
 	    ("setting up sdram_timing_control_low (0x1408) with: %08x \n",
-	     0x01501220));
+	     0x01501220);
 	/*ronen db64460 */
 	GT_REG_WRITE (SDRAM_TIMING_CONTROL_LOW, 0x01501220);
 
@@ -1611,10 +1594,10 @@ int setup_sdram (AUX_MEM_DIMM_INFO * info)
 	if (info->registeredAddrAndControlInputs
 	    || info->registeredDQMBinputs) {
 		tmp |= (1 << 17);
-		DP (printf
+		debug
 		    ("SPD says: registered Addr. and Cont.: %d; registered DQMBinputs: %d\n",
 		     info->registeredAddrAndControlInputs,
-		     info->registeredDQMBinputs));
+		     info->registeredDQMBinputs);
 	}
 
 	/* Use buffer 1 to return read data to the CPU
@@ -1624,29 +1607,29 @@ indent: Standard input:1465: Warning:old style assignment ambiguity in "=*".  As
 
 4460 */
 	tmp |= (1 << 26);
-	DP (printf
+	debug
 	    ("Before Buffer assignment - sdram_conf (0x1400): %08x\n",
-	     GTREGREAD (SDRAM_CONFIG)));
-	DP (printf
+	     GTREGREAD (SDRAM_CONFIG));
+	debug
 	    ("After Buffer assignment - sdram_conf (0x1400): %08x\n",
-	     GTREGREAD (SDRAM_CONFIG)));
+	     GTREGREAD (SDRAM_CONFIG));
 
 	/* SDRAM timing To_do: */
 /* ------------------------------------------------------------------------------ */
 	/* ronen db64460 */
-	DP (printf
+	debug
 	    ("setting up sdram_timing_control_high (0x140c) with: %08x \n",
-	     0xc));
+	     0xc);
 	GT_REG_WRITE (SDRAM_TIMING_CONTROL_HIGH, 0xc);
 
-	DP (printf
+	debug
 	    ("setting up sdram address pads control (0x14c0) with: %08x \n",
-	     0x7d5014a));
+	     0x7d5014a);
 	GT_REG_WRITE (SDRAM_ADDR_CTRL_PADS_CALIBRATION, 0x7d5014a);
 
-	DP (printf
+	debug
 	    ("setting up sdram data pads control (0x14c4) with: %08x \n",
-	     0x7d5014a));
+	     0x7d5014a);
 	GT_REG_WRITE (SDRAM_DATA_PADS_CALIBRATION, 0x7d5014a);
 
 /* ------------------------------------------------------------------------------ */
@@ -1656,8 +1639,8 @@ indent: Standard input:1465: Warning:old style assignment ambiguity in "=*".  As
 /*      for (i = info->slot * 2; i < ((info->slot * 2) + info->banks); i++) */
 	{
 		i = info->slot;
-		DP (printf
-		    ("\n*** Running a MRS cycle for bank %d ***\n", i));
+		debug
+		    ("\n*** Running a MRS cycle for bank %d ***\n", i);
 
 		/* map the bank */
 		memory_map_bank (i, 0, GB / 4);
@@ -1665,17 +1648,17 @@ indent: Standard input:1465: Warning:old style assignment ambiguity in "=*".  As
 		/* set SDRAM mode */ /* To_do check it */
 		GT_REG_WRITE (SDRAM_OPERATION, 0x3);
 		check = GTREGREAD (SDRAM_OPERATION);
-		DP (printf
+		debug
 		    ("\n*** SDRAM_OPERATION 1418 (0 = Normal Operation) = %08lx ***\n",
-		     check));
+		     check);
 
 
 		/* switch back to normal operation mode */
 		GT_REG_WRITE (SDRAM_OPERATION, 0);
 		check = GTREGREAD (SDRAM_OPERATION);
-		DP (printf
+		debug
 		    ("\n*** SDRAM_OPERATION 1418 (0 = Normal Operation) = %08lx ***\n",
-		     check));
+		     check);
 
 		/* unmap the bank */
 		memory_map_bank (i, 0, 0);
@@ -1721,9 +1704,9 @@ long int dram_size (long int *base, long int maxsize)
 		*b = save2;
 
 		if (val != cnt) {
-			DP (printf
+			debug
 			    ("Found %08x  at Address %08x (failure)\n",
-			     (unsigned int) val, (unsigned int) addr));
+			     (unsigned int) val, (unsigned int) addr);
 			/* fix boundary condition.. STARTVAL means zero */
 			if (cnt == STARTVAL / sizeof (long))
 				cnt = 0;
@@ -1739,9 +1722,8 @@ long int dram_size (long int *base, long int maxsize)
  * controlling logic happens */
 phys_size_t initdram (int board_type)
 {
-	int s0 = 0, s1 = 0;
 	int checkbank[4] = {[0 ... 3] = 0 };
-	ulong realsize, total, check;
+	ulong realsize, total;
 	AUX_MEM_DIMM_INFO dimmInfo1;
 	AUX_MEM_DIMM_INFO dimmInfo2;
 	int nhr, bank_no;
@@ -1756,10 +1738,10 @@ phys_size_t initdram (int board_type)
 		printf ("Skipping SD- DDRRAM setup due to NHR bit being set\n");
 	} else {
 		/* DIMM0 */
-		s0 = check_dimm (0, &dimmInfo1);
+		check_dimm (0, &dimmInfo1);
 
 		/* DIMM1 */
-		s1 = check_dimm (1, &dimmInfo2);
+		check_dimm (1, &dimmInfo2);
 
 		memory_map_bank (0, 0, 0);
 		memory_map_bank (1, 0, 0);
@@ -1793,7 +1775,6 @@ phys_size_t initdram (int board_type)
 	/* next, size the SDRAM banks */
 
 	realsize = total = 0;
-	check = GB / 4;
 	if (dimmInfo1.numOfModuleBanks > 0) {
 		checkbank[0] = 1;
 	}
