@@ -42,6 +42,8 @@ config KS8851
select NET_CORE
select MII
select CRC32
+ select MISC_DEVICES
+ select EEPROM_93CX6
---help---
SPI driver for Micrel KS8851 SPI attached network chip.
@@ -22,6 +22,7 @@
#include <linux/cache.h>
#include <linux/crc32.h>
#include <linux/mii.h>
+#include <linux/eeprom_93cx6.h>
#include <linux/spi/spi.h>
@@ -82,6 +83,7 @@ union ks8851_tx_hdr {
* @rc_ccr: Cached copy of KS_CCR.
* @rc_rxqcr: Cached copy of KS_RXQCR.
* @eeprom_size: Companion eeprom size in Bytes, 0 if no eeprom
+ * @eeprom: 93CX6 EEPROM state for accessing on-board EEPROM.
*
* The @lock ensures that the chip is protected when certain operations are
* in progress. When the read or write packet transfer is in progress, most
@@ -128,6 +130,8 @@ struct ks8851_net {
struct spi_message spi_msg2;
struct spi_transfer spi_xfer1;
struct spi_transfer spi_xfer2[2];
+
+ struct eeprom_93cx6 eeprom;
};
static int msg_enable;
@@ -1071,234 +1075,6 @@ static const struct net_device_ops ks8851_netdev_ops = {
.ndo_validate_addr = eth_validate_addr,
};
-/* Companion eeprom access */
-
-enum { /* EEPROM programming states */
- EEPROM_CONTROL,
- EEPROM_ADDRESS,
- EEPROM_DATA,
- EEPROM_COMPLETE
-};
-
-/**
- * ks8851_eeprom_read - read a 16bits word in ks8851 companion EEPROM
- * @dev: The network device the PHY is on.
- * @addr: EEPROM address to read
- *
- * eeprom_size: used to define the data coding length. Can be changed
- * through debug-fs.
- *
- * Programs a read on the EEPROM using ks8851 EEPROM SW access feature.
- * Warning: The READ feature is not supported on ks8851 revision 0.
- *
- * Rough programming model:
- * - on period start: set clock high and read value on bus
- * - on period / 2: set clock low and program value on bus
- * - start on period / 2
- */
-unsigned int ks8851_eeprom_read(struct net_device *dev, unsigned int addr)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- int eepcr;
- int ctrl = EEPROM_OP_READ;
- int state = EEPROM_CONTROL;
- int bit_count = EEPROM_OP_LEN - 1;
- unsigned int data = 0;
- int dummy;
- unsigned int addr_len;
-
- addr_len = (ks->eeprom_size == 128) ? 6 : 8;
-
- /* start transaction: chip select high, authorize write */
- mutex_lock(&ks->lock);
- eepcr = EEPCR_EESA | EEPCR_EESRWA;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- eepcr |= EEPCR_EECS;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- while (state != EEPROM_COMPLETE) {
- /* falling clock period starts... */
- /* set EED_IO pin for control and address */
- eepcr &= ~EEPCR_EEDO;
- switch (state) {
- case EEPROM_CONTROL:
- eepcr |= ((ctrl >> bit_count) & 1) << 2;
- if (bit_count-- <= 0) {
- bit_count = addr_len - 1;
- state = EEPROM_ADDRESS;
- }
- break;
- case EEPROM_ADDRESS:
- eepcr |= ((addr >> bit_count) & 1) << 2;
- bit_count--;
- break;
- case EEPROM_DATA:
- /* Change to receive mode */
- eepcr &= ~EEPCR_EESRWA;
- break;
- }
-
- /* lower clock */
- eepcr &= ~EEPCR_EESCK;
-
- mutex_lock(&ks->lock);
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- /* waitread period / 2 */
- udelay(EEPROM_SK_PERIOD / 2);
-
- /* rising clock period starts... */
-
- /* raise clock */
- mutex_lock(&ks->lock);
- eepcr |= EEPCR_EESCK;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- /* Manage read */
- switch (state) {
- case EEPROM_ADDRESS:
- if (bit_count < 0) {
- bit_count = EEPROM_DATA_LEN - 1;
- state = EEPROM_DATA;
- }
- break;
- case EEPROM_DATA:
- mutex_lock(&ks->lock);
- dummy = ks8851_rdreg16(ks, KS_EEPCR);
- mutex_unlock(&ks->lock);
- data |= ((dummy >> EEPCR_EESB_OFFSET) & 1) << bit_count;
- if (bit_count-- <= 0)
- state = EEPROM_COMPLETE;
- break;
- }
-
- /* wait period / 2 */
- udelay(EEPROM_SK_PERIOD / 2);
- }
-
- /* close transaction */
- mutex_lock(&ks->lock);
- eepcr &= ~EEPCR_EECS;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- eepcr = 0;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- return data;
-}
-
-/**
- * ks8851_eeprom_write - write a 16bits word in ks8851 companion EEPROM
- * @dev: The network device the PHY is on.
- * @op: operand (can be WRITE, EWEN, EWDS)
- * @addr: EEPROM address to write
- * @data: data to write
- *
- * eeprom_size: used to define the data coding length. Can be changed
- * through debug-fs.
- *
- * Programs a write on the EEPROM using ks8851 EEPROM SW access feature.
- *
- * Note that a write enable is required before writing data.
- *
- * Rough programming model:
- * - on period start: set clock high
- * - on period / 2: set clock low and program value on bus
- * - start on period / 2
- */
-void ks8851_eeprom_write(struct net_device *dev, unsigned int op,
- unsigned int addr, unsigned int data)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- int eepcr;
- int state = EEPROM_CONTROL;
- int bit_count = EEPROM_OP_LEN - 1;
- unsigned int addr_len;
-
- addr_len = (ks->eeprom_size == 128) ? 6 : 8;
-
- switch (op) {
- case EEPROM_OP_EWEN:
- addr = 0x30;
- break;
- case EEPROM_OP_EWDS:
- addr = 0;
- break;
- }
-
- /* start transaction: chip select high, authorize write */
- mutex_lock(&ks->lock);
- eepcr = EEPCR_EESA | EEPCR_EESRWA;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- eepcr |= EEPCR_EECS;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- while (state != EEPROM_COMPLETE) {
- /* falling clock period starts... */
- /* set EED_IO pin for control and address */
- eepcr &= ~EEPCR_EEDO;
- switch (state) {
- case EEPROM_CONTROL:
- eepcr |= ((op >> bit_count) & 1) << 2;
- if (bit_count-- <= 0) {
- bit_count = addr_len - 1;
- state = EEPROM_ADDRESS;
- }
- break;
- case EEPROM_ADDRESS:
- eepcr |= ((addr >> bit_count) & 1) << 2;
- if (bit_count-- <= 0) {
- if (op == EEPROM_OP_WRITE) {
- bit_count = EEPROM_DATA_LEN - 1;
- state = EEPROM_DATA;
- } else {
- state = EEPROM_COMPLETE;
- }
- }
- break;
- case EEPROM_DATA:
- eepcr |= ((data >> bit_count) & 1) << 2;
- if (bit_count-- <= 0)
- state = EEPROM_COMPLETE;
- break;
- }
-
- /* lower clock */
- eepcr &= ~EEPCR_EESCK;
-
- mutex_lock(&ks->lock);
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- /* wait period / 2 */
- udelay(EEPROM_SK_PERIOD / 2);
-
- /* rising clock period starts... */
-
- /* raise clock */
- eepcr |= EEPCR_EESCK;
- mutex_lock(&ks->lock);
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
- /* wait period / 2 */
- udelay(EEPROM_SK_PERIOD / 2);
- }
-
- /* close transaction */
- mutex_lock(&ks->lock);
- eepcr &= ~EEPCR_EECS;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- eepcr = 0;
- ks8851_wrreg16(ks, KS_EEPCR, eepcr);
- mutex_unlock(&ks->lock);
-
-}
-
/* ethtool support */
static void ks8851_get_drvinfo(struct net_device *dev,
@@ -1345,115 +1121,141 @@ static int ks8851_nway_reset(struct net_device *dev)
return mii_nway_restart(&ks->mii);
}
-static int ks8851_get_eeprom_len(struct net_device *dev)
-{
- struct ks8851_net *ks = netdev_priv(dev);
- return ks->eeprom_size;
-}
+/* EEPROM support */
-static int ks8851_get_eeprom(struct net_device *dev,
- struct ethtool_eeprom *eeprom, u8 *bytes)
+static void ks8851_eeprom_regread(struct eeprom_93cx6 *ee)
{
- struct ks8851_net *ks = netdev_priv(dev);
- u16 *eeprom_buff;
- int first_word;
- int last_word;
- int ret_val = 0;
- u16 i;
-
- if (eeprom->len == 0)
- return -EINVAL;
+ struct ks8851_net *ks = ee->data;
+ unsigned val;
- if (eeprom->len > ks->eeprom_size)
- return -EINVAL;
+ val = ks8851_rdreg16(ks, KS_EEPCR);
- eeprom->magic = ks8851_rdreg16(ks, KS_CIDER);
+ ee->reg_data_out = (val & EEPCR_EESB) ? 1 : 0;
+ ee->reg_data_clock = (val & EEPCR_EESCK) ? 1 : 0;
+ ee->reg_chip_select = (val & EEPCR_EECS) ? 1 : 0;
+}
- first_word = eeprom->offset >> 1;
- last_word = (eeprom->offset + eeprom->len - 1) >> 1;
+static void ks8851_eeprom_regwrite(struct eeprom_93cx6 *ee)
+{
+ struct ks8851_net *ks = ee->data;
+ unsigned val = EEPCR_EESA; /* default - eeprom access on */
+
+ if (ee->drive_data)
+ val |= EEPCR_EESRWA;
+ if (ee->reg_data_in)
+ val |= EEPCR_EEDO;
+ if (ee->reg_data_clock)
+ val |= EEPCR_EESCK;
+ if (ee->reg_chip_select)
+ val |= EEPCR_EECS;
+
+ ks8851_wrreg16(ks, KS_EEPCR, val);
+}
- eeprom_buff = kmalloc(sizeof(u16) *
- (last_word - first_word + 1), GFP_KERNEL);
- if (!eeprom_buff)
- return -ENOMEM;
+/**
+ * ks8851_eeprom_claim - claim device EEPROM and activate the interface
+ * @ks: The network device state.
+ *
+ * Check for the presence of an EEPROM, and then activate software access
+ * to the device.
+ */
+static int ks8851_eeprom_claim(struct ks8851_net *ks)
+{
+ if (!(ks->rc_ccr & CCR_EEPROM))
+ return -ENOENT;
- for (i = 0; i < last_word - first_word + 1; i++)
- eeprom_buff[i] = ks8851_eeprom_read(dev, first_word + 1);
+ mutex_lock(&ks->lock);
- /* Device's eeprom is little-endian, word addressable */
- for (i = 0; i < last_word - first_word + 1; i++)
- le16_to_cpus(&eeprom_buff[i]);
+ /* start with clock low, cs high */
+ ks8851_wrreg16(ks, KS_EEPCR, EEPCR_EESA | EEPCR_EECS);
+ return 0;
+}
- memcpy(bytes, (u8 *)eeprom_buff + (eeprom->offset & 1), eeprom->len);
- kfree(eeprom_buff);
+/**
+ * ks8851_eeprom_release - release the EEPROM interface
+ * @ks: The device state
+ *
+ * Release the software access to the device EEPROM
+ */
+static void ks8851_eeprom_release(struct ks8851_net *ks)
+{
+ unsigned val = ks8851_rdreg16(ks, KS_EEPCR);
- return ret_val;
+ ks8851_wrreg16(ks, KS_EEPCR, val & ~EEPCR_EESA);
+ mutex_unlock(&ks->lock);
}
+#define KS_EEPROM_MAGIC (0x00008851)
+
static int ks8851_set_eeprom(struct net_device *dev,
- struct ethtool_eeprom *eeprom, u8 *bytes)
+ struct ethtool_eeprom *ee, u8 *data)
{
struct ks8851_net *ks = netdev_priv(dev);
- u16 *eeprom_buff;
- void *ptr;
- int max_len;
- int first_word;
- int last_word;
- int ret_val = 0;
- u16 i;
-
- if (eeprom->len == 0)
- return -EOPNOTSUPP;
-
- if (eeprom->len > ks->eeprom_size)
+ int offset = ee->offset;
+ int len = ee->len;
+ u16 tmp;
+
+ /* currently only support byte writing */
+ if (len != 1)
return -EINVAL;
- if (eeprom->magic != ks8851_rdreg16(ks, KS_CIDER))
- return -EFAULT;
+ if (ee->magic != KS_EEPROM_MAGIC)
+ return -EINVAL;
- first_word = eeprom->offset >> 1;
- last_word = (eeprom->offset + eeprom->len - 1) >> 1;
- max_len = (last_word - first_word + 1) * 2;
- eeprom_buff = kmalloc(max_len, GFP_KERNEL);
- if (!eeprom_buff)
- return -ENOMEM;
+ if (ks8851_eeprom_claim(ks))
+ return -ENOENT;
+
+ eeprom_93cx6_wren(&ks->eeprom, true);
+
+ /* ethtool currently only supports writing bytes, which means
+ * we have to read/modify/write our 16bit EEPROMs */
- ptr = (void *)eeprom_buff;
+ eeprom_93cx6_read(&ks->eeprom, offset/2, &tmp);
- if (eeprom->offset & 1) {
- /* need read/modify/write of first changed EEPROM word */
- /* only the second byte of the word is being modified */
- eeprom_buff[0] = ks8851_eeprom_read(dev, first_word);
- ptr++;
+ if (offset & 1) {
+ tmp &= 0xff;
+ tmp |= *data << 8;
+ } else {
+ tmp &= 0xff00;
+ tmp |= *data;
}
- if ((eeprom->offset + eeprom->len) & 1)
- /* need read/modify/write of last changed EEPROM word */
- /* only the first byte of the word is being modified */
- eeprom_buff[last_word - first_word] =
- ks8851_eeprom_read(dev, last_word);
+ eeprom_93cx6_write(&ks->eeprom, offset/2, tmp);
+ eeprom_93cx6_wren(&ks->eeprom, false);
+
+ ks8851_eeprom_release(ks);
+
+ return 0;
+}
- /* Device's eeprom is little-endian, word addressable */
- le16_to_cpus(&eeprom_buff[0]);
- le16_to_cpus(&eeprom_buff[last_word - first_word]);
+static int ks8851_get_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *ee, u8 *data)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+ int offset = ee->offset;
+ int len = ee->len;
- memcpy(ptr, bytes, eeprom->len);
+ /* must be 2 byte aligned */
+ if (len & 1 || offset & 1)
+ return -EINVAL;
- for (i = 0; i < last_word - first_word + 1; i++)
- eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]);
+ if (ks8851_eeprom_claim(ks))
+ return -ENOENT;
- ks8851_eeprom_write(dev, EEPROM_OP_EWEN, 0, 0);
+ ee->magic = KS_EEPROM_MAGIC;
- for (i = 0; i < last_word - first_word + 1; i++) {
- ks8851_eeprom_write(dev, EEPROM_OP_WRITE, first_word + i,
- eeprom_buff[i]);
- mdelay(EEPROM_WRITE_TIME);
- }
+ eeprom_93cx6_multiread(&ks->eeprom, offset/2, (__le16 *)data, len/2);
+ ks8851_eeprom_release(ks);
- ks8851_eeprom_write(dev, EEPROM_OP_EWDS, 0, 0);
+ return 0;
+}
- kfree(eeprom_buff);
- return ret_val;
+static int ks8851_get_eeprom_len(struct net_device *dev)
+{
+ struct ks8851_net *ks = netdev_priv(dev);
+
+ /* currently, we assume it is an 93C46 attached, so return 128 */
+ return ks->rc_ccr & CCR_EEPROM ? 128 : 0;
}
static const struct ethtool_ops ks8851_ethtool_ops = {
@@ -1646,6 +1448,13 @@ static int __devinit ks8851_probe(struct spi_device *spi)
spi_message_add_tail(&ks->spi_xfer2[0], &ks->spi_msg2);
spi_message_add_tail(&ks->spi_xfer2[1], &ks->spi_msg2);
+ /* setup EEPROM state */
+
+ ks->eeprom.data = ks;
+ ks->eeprom.width = PCI_EEPROM_WIDTH_93C46;
+ ks->eeprom.register_read = ks8851_eeprom_regread;
+ ks->eeprom.register_write = ks8851_eeprom_regwrite;
+
/* setup mii state */
ks->mii.dev = ndev;
ks->mii.phy_id = 1,
@@ -27,22 +27,11 @@
#define KS_EEPCR 0x22
#define EEPCR_EESRWA (1 << 5)
#define EEPCR_EESA (1 << 4)
-#define EEPCR_EESB_OFFSET 3
-#define EEPCR_EESB (1 << EEPCR_EESB_OFFSET)
+#define EEPCR_EESB (1 << 3)
#define EEPCR_EEDO (1 << 2)
#define EEPCR_EESCK (1 << 1)
#define EEPCR_EECS (1 << 0)
-#define EEPROM_OP_LEN 3 /* bits:*/
-#define EEPROM_OP_READ 0x06
-#define EEPROM_OP_EWEN 0x04
-#define EEPROM_OP_WRITE 0x05
-#define EEPROM_OP_EWDS 0x14
-
-#define EEPROM_DATA_LEN 16 /* 16 bits EEPROM */
-#define EEPROM_WRITE_TIME 4 /* wrt ack time in ms */
-#define EEPROM_SK_PERIOD 400 /* in us */
-
#define KS_MBIR 0x24
#define MBIR_TXMBF (1 << 12)
#define MBIR_TXMBFA (1 << 11)