diff mbox series

[V4,1/5] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings

Message ID 1578561543-23132-2-git-send-email-sricharan@codeaurora.org
State New
Headers show
Series Add minimal boot support for IPQ6018 | expand

Commit Message

Sricharan Ramabadhran Jan. 9, 2020, 9:18 a.m. UTC
Add device tree binding Documentation details for ipq6018
pinctrl driver.

Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
[V4]
  * cleaned-up schema as per Rob's comments.
  * Ran make dt_binding_check and no issues.

 .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml     | 140 +++++++++++++++++++++
 1 file changed, 140 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml

Comments

Rob Herring Jan. 13, 2020, 10:49 p.m. UTC | #1
On Thu, Jan 09, 2020 at 02:48:59PM +0530, Sricharan R wrote:
> Add device tree binding Documentation details for ipq6018
> pinctrl driver.
> 
> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> ---
> [V4]
>   * cleaned-up schema as per Rob's comments.
>   * Ran make dt_binding_check and no issues.
> 
>  .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml     | 140 +++++++++++++++++++++
>  1 file changed, 140 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> new file mode 100644
> index 0000000..68c3c8c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
> @@ -0,0 +1,140 @@
> +# SPDX-License-Identifier: GPL-2.0-or-later

Dual license please.

(GPL-2.0-only or BSD-2-Clause)

> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
> +
> +maintainers:
> +  - Sricharan R <sricharan@codeaurora.org>
> +
> +description: |
> +  This binding describes the Top Level Mode Multiplexer block found in the
> +  IPQ6018 platform.
> +
> +properties:
> +  compatible:
> +    const: qcom,ipq6018-pinctrl
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    description: Specifies the TLMM summary IRQ
> +    maxItems: 1
> +
> +  interrupt-controller: true
> +
> +  '#interrupt-cells':
> +    description:
> +      Specifies the PIN numbers and Flags, as defined in defined in
> +      include/dt-bindings/interrupt-controller/irq.h
> +    const: 2
> +
> +  gpio-controller: true
> +
> +  '#gpio-cells':
> +    description: Specifying the pin number and flags, as defined in
> +      include/dt-bindings/gpio/gpio.h
> +    const: 2
> +
> +  gpio-ranges:
> +    description: Documentation/devicetree/bindings/gpio/gpio.txt
> +    maxItems: 1
> +
> +#PIN CONFIGURATION NODES
> +patternProperties:
> +  '-pins$':
> +    type: object
> +    description:
> +      Pinctrl node's client devices use subnodes for desired pin configuration.
> +      Client device subnodes use below standard properties.
> +    allOf:
> +      - $ref: "/schemas/pinctrl/pincfg-node.yaml"
> +
> +    properties:
> +      pins:
> +        description:
> +          List of gpio pins affected by the properties specified in this
> +          subnode.
> +        allOf:
> +          - $ref: "/schemas/types.yaml#/definitions/string"

No need for type ref as the common binding does this.

> +          - enum: ['gpio$', sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd,
> +            sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
> +            qdsd_data3]
> +
> +      function:
> +        description:
> +          Specify the alternative function to be configured for the specified
> +          pins.
> +        allOf:
> +          - $ref: "/schemas/types.yaml#/definitions/string"

Same here.

> +          - enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
> +            atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
> +            atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
> +            atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp_i2c1,
> +            blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6,  blsp_spi1,
> +            blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2,
> +            blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3,
> +            blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5,
> +            blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst,
> +            cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
> +            cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
> +            dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
> +            flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
> +            gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
> +            gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
> +            ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
> +            nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
> +            pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
> +            pwr_modem_enabled_a,  pwr_modem_enabled_b, pwr_nav_enabled_a,
> +            pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
> +            qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
> +            qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
> +            qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
> +            qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
> +            sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
> +            uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
> +
> +      drive-strength:
> +        allOf:
> +          - $ref: "/schemas/types.yaml#/definitions/uint32"

Same here.

> +          - enum: [2, 4, 6, 8, 10, 12, 14, 16]

default?

> +        description:
> +          Selects the drive strength for the specified pins, in mA.

> +
> +    required:
> +      - pins
> +      - function

       additionalProperties: false

You'll need to list any other properties you use. Based 
on the example, you'll need 'bias-pull-down: true'.

> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - interrupt-controller
> +  - '#interrupt-cells'
> +  - gpio-controller
> +  - '#gpio-cells'
> +  - gpio-ranges

additionalProperties: false

> +
> +examples:
> +  - |
> +        #include <dt-bindings/interrupt-controller/arm-gic.h>
> +        tlmm: pinctrl@1000000 {
> +              compatible = "qcom,ipq6018-pinctrl";
> +              reg = <0x01000000 0x300000>;
> +              interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +              gpio-controller;
> +              #gpio-cells = <2>;
> +              gpio-ranges = <&tlmm 0 80>;
> +              interrupt-controller;
> +              #interrupt-cells = <2>;
> +
> +              serial3-pinmux {

Doesn't match the schema.

> +                      pins = "gpio44", "gpio45";
> +                      function = "blsp2_uart";
> +                      drive-strength = <8>;
> +                      bias-pull-down;
> +              };
> +        };
> -- 
> 2.7.4
>
Sricharan Ramabadhran Jan. 16, 2020, 7:48 a.m. UTC | #2
Hi Rob,
  Thanks for the review, fixed all below comments and posted V5.


On 1/14/2020 4:19 AM, Rob Herring wrote:
> On Thu, Jan 09, 2020 at 02:48:59PM +0530, Sricharan R wrote:
>> Add device tree binding Documentation details for ipq6018
>> pinctrl driver.
>>
>> Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
>> Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
>> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
>> ---
>> [V4]
>>   * cleaned-up schema as per Rob's comments.
>>   * Ran make dt_binding_check and no issues.
>>
>>  .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml     | 140 +++++++++++++++++++++
>>  1 file changed, 140 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>> new file mode 100644
>> index 0000000..68c3c8c
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
>> @@ -0,0 +1,140 @@
>> +# SPDX-License-Identifier: GPL-2.0-or-later
> 
> Dual license please.
> 
> (GPL-2.0-only or BSD-2-Clause)
>

 ok, fixed in V5
 
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
>> +
>> +maintainers:
>> +  - Sricharan R <sricharan@codeaurora.org>
>> +
>> +description: |
>> +  This binding describes the Top Level Mode Multiplexer block found in the
>> +  IPQ6018 platform.
>> +
>> +properties:
>> +  compatible:
>> +    const: qcom,ipq6018-pinctrl
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  interrupts:
>> +    description: Specifies the TLMM summary IRQ
>> +    maxItems: 1
>> +
>> +  interrupt-controller: true
>> +
>> +  '#interrupt-cells':
>> +    description:
>> +      Specifies the PIN numbers and Flags, as defined in defined in
>> +      include/dt-bindings/interrupt-controller/irq.h
>> +    const: 2
>> +
>> +  gpio-controller: true
>> +
>> +  '#gpio-cells':
>> +    description: Specifying the pin number and flags, as defined in
>> +      include/dt-bindings/gpio/gpio.h
>> +    const: 2
>> +
>> +  gpio-ranges:
>> +    description: Documentation/devicetree/bindings/gpio/gpio.txt
>> +    maxItems: 1
>> +
>> +#PIN CONFIGURATION NODES
>> +patternProperties:
>> +  '-pins$':
>> +    type: object
>> +    description:
>> +      Pinctrl node's client devices use subnodes for desired pin configuration.
>> +      Client device subnodes use below standard properties.
>> +    allOf:
>> +      - $ref: "/schemas/pinctrl/pincfg-node.yaml"
>> +
>> +    properties:
>> +      pins:
>> +        description:
>> +          List of gpio pins affected by the properties specified in this
>> +          subnode.
>> +        allOf:
>> +          - $ref: "/schemas/types.yaml#/definitions/string"
> 
> No need for type ref as the common binding does this.
>

 ok. fixed in V5.

 
>> +          - enum: ['gpio$', sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd,
>> +            sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
>> +            qdsd_data3]
>> +
>> +      function:
>> +        description:
>> +          Specify the alternative function to be configured for the specified
>> +          pins.
>> +        allOf:
>> +          - $ref: "/schemas/types.yaml#/definitions/string"
> 
> Same here.
>

 ok, fixed in V5.

 
>> +          - enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
>> +            atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
>> +            atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
>> +            atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp_i2c1,
>> +            blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6,  blsp_spi1,
>> +            blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2,
>> +            blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3,
>> +            blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5,
>> +            blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst,
>> +            cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
>> +            cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
>> +            dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
>> +            flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
>> +            gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
>> +            gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
>> +            ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
>> +            nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
>> +            pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
>> +            pwr_modem_enabled_a,  pwr_modem_enabled_b, pwr_nav_enabled_a,
>> +            pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
>> +            qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
>> +            qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
>> +            qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
>> +            qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
>> +            sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
>> +            uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
>> +
>> +      drive-strength:
>> +        allOf:
>> +          - $ref: "/schemas/types.yaml#/definitions/uint32"
> 
> Same here.
>

fixed in v5.

 
>> +          - enum: [2, 4, 6, 8, 10, 12, 14, 16]
> 
> default?
>

fixed in v5.

 
>> +        description:
>> +          Selects the drive strength for the specified pins, in mA.
> 
>> +
>> +    required:
>> +      - pins
>> +      - function
> 
>        additionalProperties: false
> 
> You'll need to list any other properties you use. Based 
> on the example, you'll need 'bias-pull-down: true'.
>

 ok, fixed in v5.

 
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - interrupts
>> +  - interrupt-controller
>> +  - '#interrupt-cells'
>> +  - gpio-controller
>> +  - '#gpio-cells'
>> +  - gpio-ranges
> 
> additionalProperties: false
>

 ok, fixed in v5.
 
>> +
>> +examples:
>> +  - |
>> +        #include <dt-bindings/interrupt-controller/arm-gic.h>
>> +        tlmm: pinctrl@1000000 {
>> +              compatible = "qcom,ipq6018-pinctrl";
>> +              reg = <0x01000000 0x300000>;
>> +              interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>> +              gpio-controller;
>> +              #gpio-cells = <2>;
>> +              gpio-ranges = <&tlmm 0 80>;
>> +              interrupt-controller;
>> +              #interrupt-cells = <2>;
>> +
>> +              serial3-pinmux {
> 
> Doesn't match the schema.

 fixed in v5.


Regards,
 Sricharan
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
new file mode 100644
index 0000000..68c3c8c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -0,0 +1,140 @@ 
+# SPDX-License-Identifier: GPL-2.0-or-later
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
+
+maintainers:
+  - Sricharan R <sricharan@codeaurora.org>
+
+description: |
+  This binding describes the Top Level Mode Multiplexer block found in the
+  IPQ6018 platform.
+
+properties:
+  compatible:
+    const: qcom,ipq6018-pinctrl
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    description: Specifies the TLMM summary IRQ
+    maxItems: 1
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    description:
+      Specifies the PIN numbers and Flags, as defined in defined in
+      include/dt-bindings/interrupt-controller/irq.h
+    const: 2
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description: Specifying the pin number and flags, as defined in
+      include/dt-bindings/gpio/gpio.h
+    const: 2
+
+  gpio-ranges:
+    description: Documentation/devicetree/bindings/gpio/gpio.txt
+    maxItems: 1
+
+#PIN CONFIGURATION NODES
+patternProperties:
+  '-pins$':
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    allOf:
+      - $ref: "/schemas/pinctrl/pincfg-node.yaml"
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/string"
+          - enum: ['gpio$', sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd,
+            sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
+            qdsd_data3]
+
+      function:
+        description:
+          Specify the alternative function to be configured for the specified
+          pins.
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/string"
+          - enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
+            atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
+            atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
+            atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp_i2c1,
+            blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6,  blsp_spi1,
+            blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3, blsp_spi2,
+            blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3, blsp_spi3,
+            blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4, blsp_spi5,
+            blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2, cam1_rst,
+            cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
+            cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
+            dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
+            flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
+            gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
+            gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
+            ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
+            nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
+            pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
+            pwr_modem_enabled_a,  pwr_modem_enabled_b, pwr_nav_enabled_a,
+            pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
+            qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
+            qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
+            qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
+            qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
+            sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
+            uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
+
+      drive-strength:
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum: [2, 4, 6, 8, 10, 12, 14, 16]
+        description:
+          Selects the drive strength for the specified pins, in mA.
+
+    required:
+      - pins
+      - function
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-controller
+  - '#interrupt-cells'
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+examples:
+  - |
+        #include <dt-bindings/interrupt-controller/arm-gic.h>
+        tlmm: pinctrl@1000000 {
+              compatible = "qcom,ipq6018-pinctrl";
+              reg = <0x01000000 0x300000>;
+              interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+              gpio-controller;
+              #gpio-cells = <2>;
+              gpio-ranges = <&tlmm 0 80>;
+              interrupt-controller;
+              #interrupt-cells = <2>;
+
+              serial3-pinmux {
+                      pins = "gpio44", "gpio45";
+                      function = "blsp2_uart";
+                      drive-strength = <8>;
+                      bias-pull-down;
+              };
+        };