| Message ID | 20111024223008.GB3305@orbis-terrarum.net |
|---|---|
| State | Not Applicable |
| Delegated to: | David Miller |
| Headers | show |
Hello. On 25.10.2011 0:30, Robin H. Johnson wrote: > In the OCZ RevoDrive3/zDrive R4 series, the "OCZ SuperScale Storage > Controller" with "Virtualized Controller Architecture 2.0" really seems > to be a Marvell 88SE9485 part, with OCZ firmware/BIOS. > > Developed and tested on OCZ RevoDrive3 120GB [PCI 1b85:1021] > > Should work on: > - OCZ RevoDrive3 (2x SandForce 2281) > - OCZ RevoDrive3 X2 (4x SandForce 2281) > - OCZ zDrive R4 CM84 (4x SandForce 2281) > - OCZ zDrive R4 CM88 (8x SandForce 2281) > - OCZ zDrive R4 RM84 (4x SandForce 2582) > - OCZ zDrive R4 RM88 (8x SandForce 2582) > > All of this because a friend recently bought a OCZ RevoDrive3 and was > bitten by the lack of Linux support. > > Notes from testing: > ------------------- > - SMART works. > - VPD Device Identification is "OCZ-REVODRIVE3" > - Thin provisioning/TRIM seems to be implemented as WRITE SAME UNMAP, > with deterministic (non-zero) read after TRIM, but I'm not sure if it > works 100% in my testing. > - Some of the tuning in the firmware seems to ensure much better > performance when in a RAID0 setup than using the two devices > seperately. > > I have not tested booting from the SSD, because all of this was > developed and tested remotely from the actual hardware. > > Signed-off-by: Robin H. Johnson<robbat2@gentoo.org> > Thanks-To: Gordon Pritchard<gordp@sfu.ca> [...] > diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h > index ae96bbe..3fe46e9 100644 > --- a/include/linux/pci_ids.h > +++ b/include/linux/pci_ids.h > @@ -2868,3 +2868,5 @@ > > #define PCI_VENDOR_ID_XEN 0x5853 > #define PCI_DEVICE_ID_XEN_PLATFORM 0x0001 > + > +#define PCI_VENDOR_ID_OCZ 0x1b85 The vendor ID macros in this file are sorted by the ID value (except Xen, it seems). WBR. Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/scsi/mvsas/mv_init.c b/drivers/scsi/mvsas/mv_init.c index 4e9af66..b88315a 100644 --- a/drivers/scsi/mvsas/mv_init.c +++ b/drivers/scsi/mvsas/mv_init.c @@ -723,6 +723,16 @@ static struct pci_device_id __devinitdata mvs_pci_table[] = { .class_mask = 0, .driver_data = chip_9485, }, + { PCI_VDEVICE(OCZ, 0x1021), chip_9485}, /* OCZ RevoDrive3 */ + { PCI_VDEVICE(OCZ, 0x1022), chip_9485}, /* OCZ RevoDrive3/zDriveR4 (exact model unknown) */ + { PCI_VDEVICE(OCZ, 0x1040), chip_9485}, /* OCZ RevoDrive3/zDriveR4 (exact model unknown) */ + { PCI_VDEVICE(OCZ, 0x1041), chip_9485}, /* OCZ RevoDrive3/zDriveR4 (exact model unknown) */ + { PCI_VDEVICE(OCZ, 0x1042), chip_9485}, /* OCZ RevoDrive3/zDriveR4 (exact model unknown) */ + { PCI_VDEVICE(OCZ, 0x1043), chip_9485}, /* OCZ RevoDrive3/zDriveR4 (exact model unknown) */ + { PCI_VDEVICE(OCZ, 0x1044), chip_9485}, /* OCZ RevoDrive3/zDriveR4 (exact model unknown) */ + { PCI_VDEVICE(OCZ, 0x1080), chip_9485}, /* OCZ RevoDrive3/zDriveR4 (exact model unknown) */ + { PCI_VDEVICE(OCZ, 0x1083), chip_9485}, /* OCZ RevoDrive3/zDriveR4 (exact model unknown) */ + { PCI_VDEVICE(OCZ, 0x1084), chip_9485}, /* OCZ RevoDrive3/zDriveR4 (exact model unknown) */ { } /* terminate list */ }; diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index ae96bbe..3fe46e9 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -2868,3 +2868,5 @@ #define PCI_VENDOR_ID_XEN 0x5853 #define PCI_DEVICE_ID_XEN_PLATFORM 0x0001 + +#define PCI_VENDOR_ID_OCZ 0x1b85
In the OCZ RevoDrive3/zDrive R4 series, the "OCZ SuperScale Storage Controller" with "Virtualized Controller Architecture 2.0" really seems to be a Marvell 88SE9485 part, with OCZ firmware/BIOS. Developed and tested on OCZ RevoDrive3 120GB [PCI 1b85:1021] Should work on: - OCZ RevoDrive3 (2x SandForce 2281) - OCZ RevoDrive3 X2 (4x SandForce 2281) - OCZ zDrive R4 CM84 (4x SandForce 2281) - OCZ zDrive R4 CM88 (8x SandForce 2281) - OCZ zDrive R4 RM84 (4x SandForce 2582) - OCZ zDrive R4 RM88 (8x SandForce 2582) All of this because a friend recently bought a OCZ RevoDrive3 and was bitten by the lack of Linux support. Notes from testing: ------------------- - SMART works. - VPD Device Identification is "OCZ-REVODRIVE3" - Thin provisioning/TRIM seems to be implemented as WRITE SAME UNMAP, with deterministic (non-zero) read after TRIM, but I'm not sure if it works 100% in my testing. - Some of the tuning in the firmware seems to ensure much better performance when in a RAID0 setup than using the two devices seperately. I have not tested booting from the SSD, because all of this was developed and tested remotely from the actual hardware. Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Thanks-To: Gordon Pritchard <gordp@sfu.ca> --- drivers/scsi/mvsas/mv_init.c | 10 ++++++++++ include/linux/pci_ids.h | 2 ++ 2 files changed, 12 insertions(+), 0 deletions(-) Resending for the v3.2 merge window. I tested it with more than 5TiB of IO, no stability problems detected. Some fio performance numbers: http://paste.pocoo.org/show/489716/ dmesg/hdparm/smartctl: http://www.ocztechnologyforum.com/forum/showthread.php?95151-Linux-patch-support-for-RevoDrive3-RevoDrive3-X2-zDrive-R4&p=686054&viewfull=1#post686054