@@ -2870,32 +2870,6 @@ Low Level (hardware related) configuration options:
If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
forced to a value that ensures that CCSR is not relocated.
-- Floppy Disk Support:
- CONFIG_SYS_FDC_DRIVE_NUMBER
-
- the default drive number (default value 0)
-
- CONFIG_SYS_ISA_IO_STRIDE
-
- defines the spacing between FDC chipset registers
- (default value 1)
-
- CONFIG_SYS_ISA_IO_OFFSET
-
- defines the offset of register from address. It
- depends on which part of the data bus is connected to
- the FDC chipset. (default value 0)
-
- If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
- CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
- default value.
-
- if CONFIG_SYS_FDC_HW_INIT is defined, then the function
- fdc_hw_init() is called at the beginning of the FDC
- setup. fdc_hw_init() must be provided by the board
- source code. It is used to make hardware-dependent
- initializations.
-
- CONFIG_IDE_AHB:
Most IDE controllers were designed to be connected with PCI
interface. Only few of them were designed for AHB interface.
@@ -842,11 +842,6 @@ config CMD_FASTBOOT
See doc/android/fastboot.txt for more information.
-config CMD_FDC
- bool "fdcboot - Boot from floppy device"
- help
- The 'fdtboot' command allows booting an image from a floppy disk.
-
config CMD_FLASH
bool "flinfo, erase, protect"
default y
@@ -58,7 +58,6 @@ obj-$(CONFIG_HUSH_PARSER) += exit.o
obj-$(CONFIG_CMD_EXT4) += ext4.o
obj-$(CONFIG_CMD_EXT2) += ext2.o
obj-$(CONFIG_CMD_FAT) += fat.o
-obj-$(CONFIG_CMD_FDC) += fdc.o
obj-$(CONFIG_CMD_FDT) += fdt.o
obj-$(CONFIG_CMD_FITUPD) += fitupd.o
obj-$(CONFIG_CMD_FLASH) += flash.o
deleted file mode 100644
@@ -1,752 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2001
- * Denis Peter, MPL AG, d.peter@mpl.ch.
- */
-/*
- * Floppy Disk support
- */
-
-#include <common.h>
-#include <config.h>
-#include <command.h>
-#include <image.h>
-#include <irq_func.h>
-
-
-#undef FDC_DEBUG
-
-#ifdef FDC_DEBUG
-#define PRINTF(fmt,args...) printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-/*#if defined(CONFIG_CMD_DATE) */
-/*#include <rtc.h> */
-/*#endif */
-
-typedef struct {
- int flags; /* connected drives ect */
- unsigned long blnr; /* Logical block nr */
- uchar drive; /* drive no */
- uchar cmdlen; /* cmd length */
- uchar cmd[16]; /* cmd desc */
- uchar dma; /* if > 0 dma enabled */
- uchar result[11]; /* status information */
- uchar resultlen; /* lenght of result */
-} FDC_COMMAND_STRUCT;
-
-/* flags: only the lower 8bit used:
- * bit 0 if set drive 0 is present
- * bit 1 if set drive 1 is present
- * bit 2 if set drive 2 is present
- * bit 3 if set drive 3 is present
- * bit 4 if set disk in drive 0 is inserted
- * bit 5 if set disk in drive 1 is inserted
- * bit 6 if set disk in drive 2 is inserted
- * bit 7 if set disk in drive 4 is inserted
- */
-
-/* cmd indexes */
-#define COMMAND 0
-#define DRIVE 1
-#define CONFIG0 1
-#define SPEC_HUTSRT 1
-#define TRACK 2
-#define CONFIG1 2
-#define SPEC_HLT 2
-#define HEAD 3
-#define CONFIG2 3
-#define SECTOR 4
-#define SECTOR_SIZE 5
-#define LAST_TRACK 6
-#define GAP 7
-#define DTL 8
-/* result indexes */
-#define STATUS_0 0
-#define STATUS_PCN 1
-#define STATUS_1 1
-#define STATUS_2 2
-#define STATUS_TRACK 3
-#define STATUS_HEAD 4
-#define STATUS_SECT 5
-#define STATUS_SECT_SIZE 6
-
-
-/* Register addresses */
-#define FDC_BASE 0x3F0
-#define FDC_SRA FDC_BASE + 0 /* Status Register A */
-#define FDC_SRB FDC_BASE + 1 /* Status Register B */
-#define FDC_DOR FDC_BASE + 2 /* Digital Output Register */
-#define FDC_TDR FDC_BASE + 3 /* Tape Drive Register */
-#define FDC_DSR FDC_BASE + 4 /* Data rate Register */
-#define FDC_MSR FDC_BASE + 4 /* Main Status Register */
-#define FDC_FIFO FDC_BASE + 5 /* FIFO */
-#define FDC_DIR FDC_BASE + 6 /* Digital Input Register */
-#define FDC_CCR FDC_BASE + 7 /* Configuration Control */
-/* Commands */
-#define FDC_CMD_SENSE_INT 0x08
-#define FDC_CMD_CONFIGURE 0x13
-#define FDC_CMD_SPECIFY 0x03
-#define FDC_CMD_RECALIBRATE 0x07
-#define FDC_CMD_READ 0x06
-#define FDC_CMD_READ_TRACK 0x02
-#define FDC_CMD_READ_ID 0x0A
-#define FDC_CMD_DUMP_REG 0x0E
-#define FDC_CMD_SEEK 0x0F
-
-#define FDC_CMD_SENSE_INT_LEN 0x01
-#define FDC_CMD_CONFIGURE_LEN 0x04
-#define FDC_CMD_SPECIFY_LEN 0x03
-#define FDC_CMD_RECALIBRATE_LEN 0x02
-#define FDC_CMD_READ_LEN 0x09
-#define FDC_CMD_READ_TRACK_LEN 0x09
-#define FDC_CMD_READ_ID_LEN 0x02
-#define FDC_CMD_DUMP_REG_LEN 0x01
-#define FDC_CMD_SEEK_LEN 0x03
-
-#define FDC_FIFO_THR 0x0C
-#define FDC_FIFO_DIS 0x00
-#define FDC_IMPLIED_SEEK 0x01
-#define FDC_POLL_DIS 0x00
-#define FDC_PRE_TRK 0x00
-#define FDC_CONFIGURE FDC_FIFO_THR | (FDC_POLL_DIS<<4) | (FDC_FIFO_DIS<<5) | (FDC_IMPLIED_SEEK << 6)
-#define FDC_MFM_MODE 0x01 /* MFM enable */
-#define FDC_SKIP_MODE 0x00 /* skip enable */
-
-#define FDC_TIME_OUT 100000 /* time out */
-#define FDC_RW_RETRIES 3 /* read write retries */
-#define FDC_CAL_RETRIES 3 /* calibration and seek retries */
-
-
-/* Disk structure */
-typedef struct {
- unsigned int size; /* nr of sectors total */
- unsigned int sect; /* sectors per track */
- unsigned int head; /* nr of heads */
- unsigned int track; /* nr of tracks */
- unsigned int stretch; /* !=0 means double track steps */
- unsigned char gap; /* gap1 size */
- unsigned char rate; /* data rate. |= 0x40 for perpendicular */
- unsigned char spec1; /* stepping rate, head unload time */
- unsigned char fmt_gap;/* gap2 size */
- unsigned char hlt; /* head load time */
- unsigned char sect_code;/* Sector Size code */
- const char * name; /* used only for predefined formats */
-} FD_GEO_STRUCT;
-
-
-/* supported Floppy types (currently only one) */
-const static FD_GEO_STRUCT floppy_type[2] = {
- { 2880,18,2,80,0,0x1B,0x00,0xCF,0x6C,16,2,"H1440" }, /* 7 1.44MB 3.5" */
- { 0, 0,0, 0,0,0x00,0x00,0x00,0x00, 0,0,NULL }, /* end of table */
-};
-
-static FDC_COMMAND_STRUCT cmd; /* global command struct */
-
-/* If the boot drive number is undefined, we assume it's drive 0 */
-#ifndef CONFIG_SYS_FDC_DRIVE_NUMBER
-#define CONFIG_SYS_FDC_DRIVE_NUMBER 0
-#endif
-
-/* Hardware access */
-#ifndef CONFIG_SYS_ISA_IO_STRIDE
-#define CONFIG_SYS_ISA_IO_STRIDE 1
-#endif
-
-#ifndef CONFIG_SYS_ISA_IO_OFFSET
-#define CONFIG_SYS_ISA_IO_OFFSET 0
-#endif
-
-/* Supporting Functions */
-/* reads a Register of the FDC */
-unsigned char read_fdc_reg(unsigned int addr)
-{
- volatile unsigned char *val =
- (volatile unsigned char *)(CONFIG_SYS_ISA_IO_BASE_ADDRESS +
- (addr * CONFIG_SYS_ISA_IO_STRIDE) +
- CONFIG_SYS_ISA_IO_OFFSET);
-
- return val [0];
-}
-
-/* writes a Register of the FDC */
-void write_fdc_reg(unsigned int addr, unsigned char val)
-{
- volatile unsigned char *tmp =
- (volatile unsigned char *)(CONFIG_SYS_ISA_IO_BASE_ADDRESS +
- (addr * CONFIG_SYS_ISA_IO_STRIDE) +
- CONFIG_SYS_ISA_IO_OFFSET);
- tmp[0]=val;
-}
-
-/* waits for an interrupt (polling) */
-int wait_for_fdc_int(void)
-{
- unsigned long timeout;
- timeout = FDC_TIME_OUT;
- while((read_fdc_reg(FDC_SRA)&0x80)==0) {
- timeout--;
- udelay(10);
- if(timeout==0) /* timeout occurred */
- return false;
- }
- return true;
-}
-
-/* reads a byte from the FIFO of the FDC and checks direction and RQM bit
- of the MSR. returns -1 if timeout, or byte if ok */
-int read_fdc_byte(void)
-{
- unsigned long timeout;
- timeout = FDC_TIME_OUT;
- while((read_fdc_reg(FDC_MSR)&0xC0)!=0xC0) {
- /* direction out and ready */
- udelay(10);
- timeout--;
- if(timeout==0) /* timeout occurred */
- return -1;
- }
- return read_fdc_reg(FDC_FIFO);
-}
-
-/* if the direction of the FIFO is wrong, this routine is used to
- empty the FIFO. Should _not_ be used */
-int fdc_need_more_output(void)
-{
- unsigned char c;
- while((read_fdc_reg(FDC_MSR)&0xC0)==0xC0) {
- c=(unsigned char)read_fdc_byte();
- printf("Error: more output: %x\n",c);
- }
- return true;
-}
-
-
-/* writes a byte to the FIFO of the FDC and checks direction and RQM bit
- of the MSR */
-int write_fdc_byte(unsigned char val)
-{
- unsigned long timeout;
- timeout = FDC_TIME_OUT;
- while((read_fdc_reg(FDC_MSR)&0xC0)!=0x80) {
- /* direction in and ready for byte */
- timeout--;
- udelay(10);
- fdc_need_more_output();
- if(timeout==0) /* timeout occurred */
- return false;
- }
- write_fdc_reg(FDC_FIFO,val);
- return true;
-}
-
-/* sets up all FDC commands and issues it to the FDC. If
- the command causes direct results (no Execution Phase)
- the result is be read as well. */
-
-int fdc_issue_cmd(FDC_COMMAND_STRUCT *pCMD,FD_GEO_STRUCT *pFG)
-{
- int i;
- unsigned long head,track,sect,timeout;
- track = pCMD->blnr / (pFG->sect * pFG->head); /* track nr */
- sect = pCMD->blnr % (pFG->sect * pFG->head); /* remaining blocks */
- head = sect / pFG->sect; /* head nr */
- sect = sect % pFG->sect; /* remaining blocks */
- sect++; /* sectors are 1 based */
- PRINTF("Cmd 0x%02x Track %ld, Head %ld, Sector %ld, Drive %d (blnr %ld)\n",
- pCMD->cmd[0],track,head,sect,pCMD->drive,pCMD->blnr);
-
- if(head|=0) { /* max heads = 2 */
- pCMD->cmd[DRIVE]=pCMD->drive | 0x04; /* head 1 */
- pCMD->cmd[HEAD]=(unsigned char) head; /* head register */
- }
- else {
- pCMD->cmd[DRIVE]=pCMD->drive; /* head 0 */
- pCMD->cmd[HEAD]=(unsigned char) head; /* head register */
- }
- pCMD->cmd[TRACK]=(unsigned char) track; /* track */
- switch (pCMD->cmd[COMMAND]) {
- case FDC_CMD_READ:
- pCMD->cmd[SECTOR]=(unsigned char) sect; /* sector */
- pCMD->cmd[SECTOR_SIZE]=pFG->sect_code; /* sector size code */
- pCMD->cmd[LAST_TRACK]=pFG->sect; /* End of track */
- pCMD->cmd[GAP]=pFG->gap; /* gap */
- pCMD->cmd[DTL]=0xFF; /* DTL */
- pCMD->cmdlen=FDC_CMD_READ_LEN;
- pCMD->cmd[COMMAND]|=(FDC_MFM_MODE<<6); /* set MFM bit */
- pCMD->cmd[COMMAND]|=(FDC_SKIP_MODE<<5); /* set Skip bit */
- pCMD->resultlen=0; /* result only after execution */
- break;
- case FDC_CMD_SEEK:
- pCMD->cmdlen=FDC_CMD_SEEK_LEN;
- pCMD->resultlen=0; /* no result */
- break;
- case FDC_CMD_CONFIGURE:
- pCMD->cmd[CONFIG0]=0;
- pCMD->cmd[CONFIG1]=FDC_CONFIGURE; /* FIFO Threshold, Poll, Enable FIFO */
- pCMD->cmd[CONFIG2]=FDC_PRE_TRK; /* Precompensation Track */
- pCMD->cmdlen=FDC_CMD_CONFIGURE_LEN;
- pCMD->resultlen=0; /* no result */
- break;
- case FDC_CMD_SPECIFY:
- pCMD->cmd[SPEC_HUTSRT]=pFG->spec1;
- pCMD->cmd[SPEC_HLT]=(pFG->hlt)<<1; /* head load time */
- if(pCMD->dma==0)
- pCMD->cmd[SPEC_HLT]|=0x1; /* no dma */
- pCMD->cmdlen=FDC_CMD_SPECIFY_LEN;
- pCMD->resultlen=0; /* no result */
- break;
- case FDC_CMD_DUMP_REG:
- pCMD->cmdlen=FDC_CMD_DUMP_REG_LEN;
- pCMD->resultlen=10; /* 10 byte result */
- break;
- case FDC_CMD_READ_ID:
- pCMD->cmd[COMMAND]|=(FDC_MFM_MODE<<6); /* set MFM bit */
- pCMD->cmdlen=FDC_CMD_READ_ID_LEN;
- pCMD->resultlen=7; /* 7 byte result */
- break;
- case FDC_CMD_RECALIBRATE:
- pCMD->cmd[DRIVE]&=0x03; /* don't set the head bit */
- pCMD->cmdlen=FDC_CMD_RECALIBRATE_LEN;
- pCMD->resultlen=0; /* no result */
- break;
- break;
- case FDC_CMD_SENSE_INT:
- pCMD->cmdlen=FDC_CMD_SENSE_INT_LEN;
- pCMD->resultlen=2;
- break;
- }
- for(i=0;i<pCMD->cmdlen;i++) {
- /* PRINTF("write cmd%d = 0x%02X\n",i,pCMD->cmd[i]); */
- if (write_fdc_byte(pCMD->cmd[i]) == false) {
- PRINTF("Error: timeout while issue cmd%d\n",i);
- return false;
- }
- }
- timeout=FDC_TIME_OUT;
- for(i=0;i<pCMD->resultlen;i++) {
- while((read_fdc_reg(FDC_MSR)&0xC0)!=0xC0) {
- timeout--;
- if(timeout==0) {
- PRINTF(" timeout while reading result%d MSR=0x%02X\n",i,read_fdc_reg(FDC_MSR));
- return false;
- }
- }
- pCMD->result[i]=(unsigned char)read_fdc_byte();
- }
- return true;
-}
-
-/* selects the drive assigned in the cmd structur and
- switches on the Motor */
-void select_fdc_drive(FDC_COMMAND_STRUCT *pCMD)
-{
- unsigned char val;
-
- val=(1<<(4+pCMD->drive))|pCMD->drive|0xC; /* set reset, dma gate and motor bits */
- if((read_fdc_reg(FDC_DOR)&val)!=val) {
- write_fdc_reg(FDC_DOR,val);
- for(val=0;val<255;val++)
- udelay(500); /* wait some time to start motor */
- }
-}
-
-/* switches off the Motor of the specified drive */
-void stop_fdc_drive(FDC_COMMAND_STRUCT *pCMD)
-{
- unsigned char val;
-
- val=(1<<(4+pCMD->drive))|pCMD->drive; /* sets motor bits */
- write_fdc_reg(FDC_DOR,(read_fdc_reg(FDC_DOR)&~val));
-}
-
-/* issues a recalibrate command, waits for interrupt and
- * issues a sense_interrupt */
-int fdc_recalibrate(FDC_COMMAND_STRUCT *pCMD,FD_GEO_STRUCT *pFG)
-{
- pCMD->cmd[COMMAND]=FDC_CMD_RECALIBRATE;
- if (fdc_issue_cmd(pCMD, pFG) == false)
- return false;
- while (wait_for_fdc_int() != true);
-
- pCMD->cmd[COMMAND]=FDC_CMD_SENSE_INT;
- return(fdc_issue_cmd(pCMD,pFG));
-}
-
-/* issues a recalibrate command, waits for interrupt and
- * issues a sense_interrupt */
-int fdc_seek(FDC_COMMAND_STRUCT *pCMD,FD_GEO_STRUCT *pFG)
-{
- pCMD->cmd[COMMAND]=FDC_CMD_SEEK;
- if (fdc_issue_cmd(pCMD, pFG) == false)
- return false;
- while (wait_for_fdc_int() != true);
-
- pCMD->cmd[COMMAND]=FDC_CMD_SENSE_INT;
- return(fdc_issue_cmd(pCMD,pFG));
-}
-
-/* terminates current command, by not servicing the FIFO
- * waits for interrupt and fills in the result bytes */
-int fdc_terminate(FDC_COMMAND_STRUCT *pCMD)
-{
- int i;
- for(i=0;i<100;i++)
- udelay(500); /* wait 500usec for fifo overrun */
- while((read_fdc_reg(FDC_SRA)&0x80)==0x00); /* wait as long as no int has occurred */
- for(i=0;i<7;i++) {
- pCMD->result[i]=(unsigned char)read_fdc_byte();
- }
- return true;
-}
-
-/* reads data from FDC, seek commands are issued automatic */
-int fdc_read_data(unsigned char *buffer, unsigned long blocks,FDC_COMMAND_STRUCT *pCMD, FD_GEO_STRUCT *pFG)
-{
- /* first seek to start address */
- unsigned long len,readblk,i,timeout,ii,offset;
- unsigned char c,retriesrw,retriescal;
- unsigned char *bufferw; /* working buffer */
- int sect_size;
- int flags;
-
- flags=disable_interrupts(); /* switch off all Interrupts */
- select_fdc_drive(pCMD); /* switch on drive */
- sect_size=0x080<<pFG->sect_code;
- retriesrw=0;
- retriescal=0;
- offset=0;
- if (fdc_seek(pCMD, pFG) == false) {
- stop_fdc_drive(pCMD);
- if (flags)
- enable_interrupts();
- return false;
- }
- if((pCMD->result[STATUS_0]&0x20)!=0x20) {
- printf("Seek error Status: %02X\n",pCMD->result[STATUS_0]);
- stop_fdc_drive(pCMD);
- if (flags)
- enable_interrupts();
- return false;
- }
- /* now determine the next seek point */
- /* lastblk=pCMD->blnr + blocks; */
- /* readblk=(pFG->head*pFG->sect)-(pCMD->blnr%(pFG->head*pFG->sect)); */
- readblk=pFG->sect-(pCMD->blnr%pFG->sect);
- PRINTF("1st nr of block possible read %ld start %ld\n",readblk,pCMD->blnr);
- if(readblk>blocks) /* is end within 1st track */
- readblk=blocks; /* yes, correct it */
- PRINTF("we read %ld blocks start %ld\n",readblk,pCMD->blnr);
- bufferw = &buffer[0]; /* setup working buffer */
- do {
-retryrw:
- len=sect_size * readblk;
- pCMD->cmd[COMMAND]=FDC_CMD_READ;
- if (fdc_issue_cmd(pCMD, pFG) == false) {
- stop_fdc_drive(pCMD);
- if (flags)
- enable_interrupts();
- return false;
- }
- for (i=0;i<len;i++) {
- timeout=FDC_TIME_OUT;
- do {
- c=read_fdc_reg(FDC_MSR);
- if((c&0xC0)==0xC0) {
- bufferw[i]=read_fdc_reg(FDC_FIFO);
- break;
- }
- if((c&0xC0)==0x80) { /* output */
- PRINTF("Transfer error transferred: at %ld, MSR=%02X\n",i,c);
- if(i>6) {
- for(ii=0;ii<7;ii++) {
- pCMD->result[ii]=bufferw[(i-7+ii)];
- } /* for */
- }
- if(retriesrw++>FDC_RW_RETRIES) {
- if (retriescal++>FDC_CAL_RETRIES) {
- stop_fdc_drive(pCMD);
- if (flags)
- enable_interrupts();
- return false;
- }
- else {
- PRINTF(" trying to recalibrate Try %d\n",retriescal);
- if (fdc_recalibrate(pCMD, pFG) == false) {
- stop_fdc_drive(pCMD);
- if (flags)
- enable_interrupts();
- return false;
- }
- retriesrw=0;
- goto retrycal;
- } /* else >FDC_CAL_RETRIES */
- }
- else {
- PRINTF("Read retry %d\n",retriesrw);
- goto retryrw;
- } /* else >FDC_RW_RETRIES */
- }/* if output */
- timeout--;
- } while (true);
- } /* for len */
- /* the last sector of a track or all data has been read,
- * we need to get the results */
- fdc_terminate(pCMD);
- offset+=(sect_size*readblk); /* set up buffer pointer */
- bufferw = &buffer[offset];
- pCMD->blnr+=readblk; /* update current block nr */
- blocks-=readblk; /* update blocks */
- if(blocks==0)
- break; /* we are finish */
- /* setup new read blocks */
- /* readblk=pFG->head*pFG->sect; */
- readblk=pFG->sect;
- if(readblk>blocks)
- readblk=blocks;
-retrycal:
- /* a seek is necessary */
- if (fdc_seek(pCMD, pFG) == false) {
- stop_fdc_drive(pCMD);
- if (flags)
- enable_interrupts();
- return false;
- }
- if((pCMD->result[STATUS_0]&0x20)!=0x20) {
- PRINTF("Seek error Status: %02X\n",pCMD->result[STATUS_0]);
- stop_fdc_drive(pCMD);
- return false;
- }
- } while (true); /* start over */
- stop_fdc_drive(pCMD); /* switch off drive */
- if (flags)
- enable_interrupts();
- return true;
-}
-
-/* Scan all drives and check if drive is present and disk is inserted */
-int fdc_check_drive(FDC_COMMAND_STRUCT *pCMD, FD_GEO_STRUCT *pFG)
-{
- int i,drives,state;
- /* OK procedure of data book is satisfied.
- * trying to get some information over the drives */
- state=0; /* no drives, no disks */
- for(drives=0;drives<4;drives++) {
- pCMD->drive=drives;
- select_fdc_drive(pCMD);
- pCMD->blnr=0; /* set to the 1st block */
- if (fdc_recalibrate(pCMD, pFG) == false)
- continue;
- if((pCMD->result[STATUS_0]&0x10)==0x10)
- continue;
- /* ok drive connected check for disk */
- state|=(1<<drives);
- pCMD->blnr=pFG->size; /* set to the last block */
- if (fdc_seek(pCMD, pFG) == false)
- continue;
- pCMD->blnr=0; /* set to the 1st block */
- if (fdc_recalibrate(pCMD, pFG) == false)
- continue;
- pCMD->cmd[COMMAND]=FDC_CMD_READ_ID;
- if (fdc_issue_cmd(pCMD, pFG) == false)
- continue;
- state|=(0x10<<drives);
- }
- stop_fdc_drive(pCMD);
- for(i=0;i<4;i++) {
- PRINTF("Floppy Drive %d %sconnected %sDisk inserted %s\n",i,
- ((state&(1<<i))==(1<<i)) ? "":"not ",
- ((state&(0x10<<i))==(0x10<<i)) ? "":"no ",
- ((state&(0x10<<i))==(0x10<<i)) ? pFG->name : "");
- }
- pCMD->flags=state;
- return true;
-}
-
-
-/**************************************************************************
-* int fdc_setup
-* setup the fdc according the datasheet
-* assuming in PS2 Mode
-*/
-int fdc_setup(int drive, FDC_COMMAND_STRUCT *pCMD, FD_GEO_STRUCT *pFG)
-{
- int i;
-
-#ifdef CONFIG_SYS_FDC_HW_INIT
- fdc_hw_init ();
-#endif
- /* first, we reset the FDC via the DOR */
- write_fdc_reg(FDC_DOR,0x00);
- for(i=0; i<255; i++) /* then we wait some time */
- udelay(500);
- /* then, we clear the reset in the DOR */
- pCMD->drive=drive;
- select_fdc_drive(pCMD);
- /* initialize the CCR */
- write_fdc_reg(FDC_CCR,pFG->rate);
- /* then initialize the DSR */
- write_fdc_reg(FDC_DSR,pFG->rate);
- if (wait_for_fdc_int() == false) {
- PRINTF("Time Out after writing CCR\n");
- return false;
- }
- /* now issue sense Interrupt and status command
- * assuming only one drive present (drive 0) */
- pCMD->dma=0; /* we don't use any dma at all */
- for(i=0;i<4;i++) {
- /* issue sense interrupt for all 4 possible drives */
- pCMD->cmd[COMMAND]=FDC_CMD_SENSE_INT;
- if (fdc_issue_cmd(pCMD, pFG) == false) {
- PRINTF("Sense Interrupt for drive %d failed\n",i);
- }
- }
- /* issue the configure command */
- pCMD->drive=drive;
- select_fdc_drive(pCMD);
- pCMD->cmd[COMMAND]=FDC_CMD_CONFIGURE;
- if (fdc_issue_cmd(pCMD, pFG) == false) {
- PRINTF(" configure timeout\n");
- stop_fdc_drive(pCMD);
- return false;
- }
- /* issue specify command */
- pCMD->cmd[COMMAND]=FDC_CMD_SPECIFY;
- if (fdc_issue_cmd(pCMD, pFG) == false) {
- PRINTF(" specify timeout\n");
- stop_fdc_drive(pCMD);
- return false;
-
- }
- /* then, we clear the reset in the DOR */
- /* fdc_check_drive(pCMD,pFG); */
- /* write_fdc_reg(FDC_DOR,0x04); */
-
- return true;
-}
-
-/****************************************************************************
- * main routine do_fdcboot
- */
-int do_fdcboot (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- FD_GEO_STRUCT *pFG = (FD_GEO_STRUCT *)floppy_type;
- FDC_COMMAND_STRUCT *pCMD = &cmd;
- unsigned long addr,imsize;
-#if defined(CONFIG_LEGACY_IMAGE_FORMAT)
- image_header_t *hdr; /* used for fdc boot */
-#endif
- unsigned char boot_drive;
- int i,nrofblk;
-#if defined(CONFIG_FIT)
- const void *fit_hdr = NULL;
-#endif
-
- switch (argc) {
- case 1:
- addr = CONFIG_SYS_LOAD_ADDR;
- boot_drive=CONFIG_SYS_FDC_DRIVE_NUMBER;
- break;
- case 2:
- addr = simple_strtoul(argv[1], NULL, 16);
- boot_drive=CONFIG_SYS_FDC_DRIVE_NUMBER;
- break;
- case 3:
- addr = simple_strtoul(argv[1], NULL, 16);
- boot_drive=simple_strtoul(argv[2], NULL, 10);
- break;
- default:
- return CMD_RET_USAGE;
- }
- /* setup FDC and scan for drives */
- if (fdc_setup(boot_drive, pCMD, pFG) == false) {
- printf("\n** Error in setup FDC **\n");
- return 1;
- }
- if (fdc_check_drive(pCMD, pFG) == false) {
- printf("\n** Error in check_drives **\n");
- return 1;
- }
- if((pCMD->flags&(1<<boot_drive))==0) {
- /* drive not available */
- printf("\n** Drive %d not availabe **\n",boot_drive);
- return 1;
- }
- if((pCMD->flags&(0x10<<boot_drive))==0) {
- /* no disk inserted */
- printf("\n** No disk inserted in drive %d **\n",boot_drive);
- return 1;
- }
- /* ok, we have a valid source */
- pCMD->drive=boot_drive;
- /* read first block */
- pCMD->blnr=0;
- if (fdc_read_data((unsigned char *)addr, 1, pCMD, pFG) == false) {
- printf("\nRead error:");
- for(i=0;i<7;i++)
- printf("result%d: 0x%02X\n",i,pCMD->result[i]);
- return 1;
- }
-
- switch (genimg_get_format ((void *)addr)) {
-#if defined(CONFIG_LEGACY_IMAGE_FORMAT)
- case IMAGE_FORMAT_LEGACY:
- hdr = (image_header_t *)addr;
- image_print_contents (hdr);
-
- imsize = image_get_image_size (hdr);
- break;
-#endif
-#if defined(CONFIG_FIT)
- case IMAGE_FORMAT_FIT:
- fit_hdr = (const void *)addr;
- puts ("Fit image detected...\n");
-
- imsize = fit_get_size (fit_hdr);
- break;
-#endif
- default:
- puts ("** Unknown image type\n");
- return 1;
- }
-
- nrofblk=imsize/512;
- if((imsize%512)>0)
- nrofblk++;
- printf("Loading %ld Bytes (%d blocks) at 0x%08lx..\n",imsize,nrofblk,addr);
- pCMD->blnr=0;
- if (fdc_read_data((unsigned char *)addr, nrofblk, pCMD, pFG) == false) {
- /* read image block */
- printf("\nRead error:");
- for(i=0;i<7;i++)
- printf("result%d: 0x%02X\n",i,pCMD->result[i]);
- return 1;
- }
- printf("OK %ld Bytes loaded.\n",imsize);
-
- flush_cache (addr, imsize);
-
-#if defined(CONFIG_FIT)
- /* This cannot be done earlier, we need complete FIT image in RAM first */
- if (genimg_get_format ((void *)addr) == IMAGE_FORMAT_FIT) {
- if (!fit_check_format (fit_hdr)) {
- puts ("** Bad FIT image format\n");
- return 1;
- }
- fit_print_contents (fit_hdr);
- }
-#endif
-
- /* Loading ok, update default load address */
- load_addr = addr;
-
- return bootm_maybe_autostart(cmdtp, argv[0]);
-}
-
-U_BOOT_CMD(
- fdcboot, 3, 1, do_fdcboot,
- "boot from floppy device",
- "loadAddr drive"
-);
@@ -47,7 +47,6 @@ obj-$(CONFIG_LED_STATUS_GPIO) += gpio_led.o
obj-$(CONFIG_MPC83XX_SERDES) += mpc83xx_serdes.o
obj-$(CONFIG_MXC_OCOTP) += mxc_ocotp.o
obj-$(CONFIG_MXS_OCOTP) += mxs_ocotp.o
-obj-$(CONFIG_NS87308) += ns87308.o
obj-$(CONFIG_NUVOTON_NCT6102D) += nuvoton_nct6102d.o
obj-$(CONFIG_PCA9551_LED) += pca9551_led.o
obj-$(CONFIG_$(SPL_)PWRSEQ) += pwrseq-uclass.o
deleted file mode 100644
@@ -1,100 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2000
- * Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
- */
-
-#include <config.h>
-
-#include <ns87308.h>
-
-void initialise_ns87308 (void)
-{
-#ifdef CONFIG_SYS_NS87308_PS2MOD
- unsigned char data;
-
- /*
- * Switch floppy drive to PS/2 mode.
- */
- read_pnp_config(SUPOERIO_CONF1, &data);
- data &= 0xFB;
- write_pnp_config(SUPOERIO_CONF1, data);
-#endif
-
-#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_KBC1)
- PNP_SET_DEVICE_BASE(LDEV_KBC1, CONFIG_SYS_NS87308_KBC1_BASE);
- write_pnp_config(LUN_CONFIG_REG, 0);
- write_pnp_config(CBASE_HIGH, 0x00);
- write_pnp_config(CBASE_LOW, 0x64);
-#endif
-
-#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_MOUSE)
- PNP_ACTIVATE_DEVICE(LDEV_MOUSE);
-#endif
-
-#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_RTC_APC)
- PNP_SET_DEVICE_BASE(LDEV_RTC_APC, CONFIG_SYS_NS87308_RTC_BASE);
-#endif
-
-#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_FDC)
- PNP_SET_DEVICE_BASE(LDEV_FDC, CONFIG_SYS_NS87308_FDC_BASE);
- write_pnp_config(LUN_CONFIG_REG, 0x40);
-#endif
-
-#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_RARP)
- PNP_SET_DEVICE_BASE(LDEV_PARP, CONFIG_SYS_NS87308_LPT_BASE);
-#endif
-
-#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_UART1)
- PNP_SET_DEVICE_BASE(LDEV_UART1, CONFIG_SYS_NS87308_UART1_BASE);
-#endif
-
-#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_UART2)
- PNP_SET_DEVICE_BASE(LDEV_UART2, CONFIG_SYS_NS87308_UART2_BASE);
-#endif
-
-#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_GPIO)
- PNP_SET_DEVICE_BASE(LDEV_GPIO, CONFIG_SYS_NS87308_GPIO_BASE);
-#endif
-
-#if (CONFIG_SYS_NS87308_DEVS & CONFIG_SYS_NS87308_POWRMAN)
-#ifndef CONFIG_SYS_NS87308_PWMAN_BASE
- PNP_ACTIVATE_DEVICE(LDEV_POWRMAN);
-#else
- PNP_SET_DEVICE_BASE(LDEV_POWRMAN, CONFIG_SYS_NS87308_PWMAN_BASE);
-
- /*
- * Enable all units
- */
- write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_FER1, 0x7d);
- write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_FER2, 0x87);
-
-#ifdef CONFIG_SYS_NS87308_PMC1
- write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_PMC1, CONFIG_SYS_NS87308_PMC1);
-#endif
-
-#ifdef CONFIG_SYS_NS87308_PMC2
- write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_PMC2, CONFIG_SYS_NS87308_PMC2);
-#endif
-
-#ifdef CONFIG_SYS_NS87308_PMC3
- write_pm_reg(CONFIG_SYS_NS87308_PWMAN_BASE, PWM_PMC3, CONFIG_SYS_NS87308_PMC3);
-#endif
-#endif
-#endif
-
-#ifdef CONFIG_SYS_NS87308_CS0_BASE
- PNP_PGCS_CSLINE_BASE(0, CONFIG_SYS_NS87308_CS0_BASE);
- PNP_PGCS_CSLINE_CONF(0, CONFIG_SYS_NS87308_CS0_CONF);
-#endif
-
-#ifdef CONFIG_SYS_NS87308_CS1_BASE
- PNP_PGCS_CSLINE_BASE(1, CONFIG_SYS_NS87308_CS1_BASE);
- PNP_PGCS_CSLINE_CONF(1, CONFIG_SYS_NS87308_CS1_CONF);
-#endif
-
-#ifdef CONFIG_SYS_NS87308_CS2_BASE
- PNP_PGCS_CSLINE_BASE(2, CONFIG_SYS_NS87308_CS2_BASE);
- PNP_PGCS_CSLINE_CONF(2, CONFIG_SYS_NS87308_CS2_CONF);
-#endif
-}
@@ -5,14 +5,9 @@
*/
#include <common.h>
-#include <linux/compiler.h>
-
#include <ns16550.h>
-#ifdef CONFIG_NS87308
-#include <ns87308.h>
-#endif
-
#include <serial.h>
+#include <linux/compiler.h>
#ifndef CONFIG_NS16550_MIN_FUNCTIONS
@@ -90,7 +90,6 @@ phys_size_t get_effective_memsize(void);
/* $(BOARD)/$(BOARD).c */
void reset_phy (void);
-void fdc_hw_init (void);
#if !defined(CONFIG_ENV_EEPROM_IS_ON_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
# define CONFIG_SYS_DEF_EEPROM_ADDR CONFIG_SYS_I2C_EEPROM_ADDR
deleted file mode 100644
@@ -1,233 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2000
- * Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
- */
-
-#ifndef _NS87308_H_
-#define _NS87308_H_
-
-#include <asm/pci_io.h>
-
-/* Note: I couldn't find a full data sheet for the ns87308, but the ns87307 seems to be pretty
- functionally- (and pin-) equivalent to the 87308, but the 308 has better ir support. */
-
-void initialise_ns87308(void);
-
-/*
- * The following struct represents the GPIO registers on the NS87308/NS97307
- */
-struct GPIO
-{
- unsigned char dta1; /* 0 data port 1 */
- unsigned char dir1; /* 1 direction port 1 */
- unsigned char out1; /* 2 output type port 1 */
- unsigned char puc1; /* 3 pull-up control port 1 */
- unsigned char dta2; /* 4 data port 2 */
- unsigned char dir2; /* 5 direction port 2 */
- unsigned char out2; /* 6 output type port 2 */
- unsigned char puc2; /* 7 pull-up control port 2 */
-};
-
-/*
- * The following represents the power management registers on the NS87308/NS97307
- */
-#define PWM_FER1 0 /* 0 function enable reg. 1 */
-#define PWM_FER2 1 /* 1 function enable reg. 2 */
-#define PWM_PMC1 2 /* 2 power mgmt. control 1 */
-#define PWM_PMC2 3 /* 3 power mgmt. control 2 */
-#define PWM_PMC3 4 /* 4 power mgmt. control 3 */
-#define PWM_WDTO 5 /* 5 watchdog time-out */
-#define PWM_WDCF 6 /* 6 watchdog config. */
-#define PWM_WDST 7 /* 7 watchdog status */
-
-/*PNP config registers:
- * these depend on the stated of BADDR1 and BADDR0 on startup
- * so there's three versions here with the last two digits indicating
- * for which configuration their valid
- * the 1st of the two digits indicates the state of BADDR1
- * the 2st of the two digits indicates the state of BADDR0
- */
-
-
-#define IO_INDEX_OFFSET_0x 0x0279 /* full PnP isa Mode */
-#define IO_INDEX_OFFSET_10 0x015C /* PnP motherboard mode */
-#define IO_INDEX_OFFSET_11 0x002E /* PnP motherboard mode */
-#define IO_DATA_OFFSET_0x 0x0A79 /* full PnP isa Mode */
-#define IO_DATA_OFFSET_10 0x015D /* PnP motherboard mode */
-#define IO_DATA_OFFSET_11 0x002F /* PnP motherboard mode */
-
-#if defined(CONFIG_SYS_NS87308_BADDR_0x)
-#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_0x)
-#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_0x)
-#elif defined(CONFIG_SYS_NS87308_BADDR_10)
-#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_10)
-#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_10)
-#elif defined(CONFIG_SYS_NS87308_BADDR_11)
-#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_11)
-#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_11)
-#endif
-
-/* PnP register definitions */
-
-#define SET_RD_DATA_PORT 0x00
-#define SERIAL_ISOLATION 0x01
-#define CONFIG_CONTROL 0x02
-#define WAKE_CSN 0x03
-#define RES_DATA 0x04
-#define STATUS 0x05
-#define SET_CSN 0x06
-#define LOGICAL_DEVICE 0x07
-
-/*vendor defined values */
-#define SID_REG 0x20
-#define SUPOERIO_CONF1 0x21
-#define SUPOERIO_CONF2 0x22
-#define PGCS_INDEX 0x23
-#define PGCS_DATA 0x24
-
-/* values above 30 are different for each logical device
- but I can't be arsed to enter them all. the ones here
- are pretty consistent between all logical devices
- feel free to correct the situation if you want.. ;)
- */
-#define ACTIVATE 0x30
-#define ACTIVATE_OFF 0x00
-#define ACTIVATE_ON 0x01
-
-#define BASE_ADDR_HIGH 0x60
-#define BASE_ADDR_LOW 0x61
-#define LUN_CONFIG_REG 0xF0
-#define DBASE_HIGH 0x60 /* SIO KBC data base address, 15:8 */
-#define DBASE_LOW 0x61 /* SIO KBC data base address, 7:0 */
-#define CBASE_HIGH 0x62 /* SIO KBC command base addr, 15:8 */
-#define CBASE_LOW 0x63 /* SIO KBC command base addr, 7:0 */
-
-/* the logical devices*/
-#define LDEV_KBC1 0x00 /* 2 devices for keyboard and mouse controller*/
-#define LDEV_KBC2 0x01
-#define LDEV_MOUSE 0x01
-#define LDEV_RTC_APC 0x02 /*Real Time Clock and Advanced Power Control*/
-#define LDEV_FDC 0x03 /*floppy disk controller*/
-#define LDEV_PARP 0x04 /*Parallel port*/
-#define LDEV_UART2 0x05
-#define LDEV_UART1 0x06
-#define LDEV_GPIO 0x07 /*General Purpose IO and chip select output signals*/
-#define LDEV_POWRMAN 0x08 /*Power Managment*/
-
-#define CONFIG_SYS_NS87308_KBC1 (1 << LDEV_KBC1)
-#define CONFIG_SYS_NS87308_KBC2 (1 << LDEV_KBC2)
-#define CONFIG_SYS_NS87308_MOUSE (1 << LDEV_MOUSE)
-#define CONFIG_SYS_NS87308_RTC_APC (1 << LDEV_RTC_APC)
-#define CONFIG_SYS_NS87308_FDC (1 << LDEV_FDC)
-#define CONFIG_SYS_NS87308_PARP (1 << LDEV_PARP)
-#define CONFIG_SYS_NS87308_UART2 (1 << LDEV_UART2)
-#define CONFIG_SYS_NS87308_UART1 (1 << LDEV_UART1)
-#define CONFIG_SYS_NS87308_GPIO (1 << LDEV_GPIO)
-#define CONFIG_SYS_NS87308_POWRMAN (1 << LDEV_POWRMAN)
-
-/*some functions and macro's for doing configuration */
-
-static inline void read_pnp_config(unsigned char index, unsigned char *data)
-{
- pci_writeb(index,IO_INDEX);
- pci_readb(IO_DATA, *data);
-}
-
-static inline void write_pnp_config(unsigned char index, unsigned char data)
-{
- pci_writeb(index,IO_INDEX);
- pci_writeb(data, IO_DATA);
-}
-
-static inline void pnp_set_device(unsigned char dev)
-{
- write_pnp_config(LOGICAL_DEVICE, dev);
-}
-
-static inline void write_pm_reg(unsigned short base, unsigned char index, unsigned char data)
-{
- pci_writeb(index, CONFIG_SYS_ISA_IO + base);
- eieio();
- pci_writeb(data, CONFIG_SYS_ISA_IO + base + 1);
-}
-
-/*void write_pnp_config(unsigned char index, unsigned char data);
-void pnp_set_device(unsigned char dev);
-*/
-
-#define PNP_SET_DEVICE_BASE(dev,base) \
- pnp_set_device(dev); \
- write_pnp_config(ACTIVATE, ACTIVATE_OFF); \
- write_pnp_config(BASE_ADDR_HIGH, ((base) >> 8) & 0xff ); \
- write_pnp_config(BASE_ADDR_LOW, (base) &0xff); \
- write_pnp_config(ACTIVATE, ACTIVATE_ON);
-
-#define PNP_ACTIVATE_DEVICE(dev) \
- pnp_set_device(dev); \
- write_pnp_config(ACTIVATE, ACTIVATE_ON);
-
-#define PNP_DEACTIVATE_DEVICE(dev) \
- pnp_set_device(dev); \
- write_pnp_config(ACTIVATE, ACTIVATE_OFF);
-
-
-static inline void write_pgcs_config(unsigned char index, unsigned char data)
-{
- write_pnp_config(PGCS_INDEX, index);
- write_pnp_config(PGCS_DATA, data);
-}
-
-/* these macrose configure the 3 CS lines
- on the sandpoint board these controll NVRAM
- CS0 is connected to NVRAMCS
- CS1 is connected to NVRAMAS0
- CS2 is connected to NVRAMAS1
- */
-#define PGCS_CS_ASSERT_ON_WRITE 0x10
-#define PGCS_CS_ASSERT_ON_READ 0x20
-
-#define PNP_PGCS_CSLINE_BASE(cs, base) \
- write_pgcs_config((cs) << 2, ((base) >> 8) & 0xff ); \
- write_pgcs_config(((cs) << 2) + 1, (base) & 0xff );
-
-#define PNP_PGCS_CSLINE_CONF(cs, conf) \
- write_pgcs_config(((cs) << 2) + 2, (conf) );
-
-
-/* The following sections are for 87308 extensions to the standard compoents it emulates */
-
-/* extensions to 16550*/
-
-#define MCR_MDSL_MSK 0xe0 /*mode select mask*/
-#define MCR_MDSL_UART 0x00 /*uart, default*/
-#define MCR_MDSL_SHRPIR 0x02 /*Sharp IR*/
-#define MCR_MDSL_SIR 0x03 /*SIR*/
-#define MCR_MDSL_CIR 0x06 /*Consumer IR*/
-
-#define FCR_TXFTH0 0x10 /* these bits control threshod of data level in fifo */
-#define FCR_TXFTH1 0x20 /* for interrupt trigger */
-
-/*
- * Default NS87308 configuration
- */
-#ifndef CONFIG_SYS_NS87308_KBC1_BASE
-#define CONFIG_SYS_NS87308_KBC1_BASE 0x0060
-#endif
-#ifndef CONFIG_SYS_NS87308_RTC_BASE
-#define CONFIG_SYS_NS87308_RTC_BASE 0x0070
-#endif
-#ifndef CONFIG_SYS_NS87308_FDC_BASE
-#define CONFIG_SYS_NS87308_FDC_BASE 0x03F0
-#endif
-#ifndef CONFIG_SYS_NS87308_LPT_BASE
-#define CONFIG_SYS_NS87308_LPT_BASE 0x0278
-#endif
-#ifndef CONFIG_SYS_NS87308_UART1_BASE
-#define CONFIG_SYS_NS87308_UART1_BASE 0x03F8
-#endif
-#ifndef CONFIG_SYS_NS87308_UART2_BASE
-#define CONFIG_SYS_NS87308_UART2_BASE 0x02F8
-#endif
-
-#endif /*_NS87308_H_*/
@@ -1243,7 +1243,6 @@ CONFIG_NO_WAIT
CONFIG_NR_DRAM_POPULATED
CONFIG_NS16550_MIN_FUNCTIONS
CONFIG_NS8382X
-CONFIG_NS87308
CONFIG_NUM_DSP_CPUS
CONFIG_NUM_PAMU
CONFIG_ODROID_REV_AIN
@@ -2298,8 +2297,6 @@ CONFIG_SYS_FAST_CLK
CONFIG_SYS_FAULT_ECHO_LINK_DOWN
CONFIG_SYS_FAULT_MII_ADDR
CONFIG_SYS_FCC_PSMR
-CONFIG_SYS_FDC_DRIVE_NUMBER
-CONFIG_SYS_FDC_HW_INIT
CONFIG_SYS_FDT_BASE
CONFIG_SYS_FDT_LOAD_ADDR
CONFIG_SYS_FDT_PAD
@@ -2974,8 +2971,6 @@ CONFIG_SYS_IO_BASE
CONFIG_SYS_ISA_BASE
CONFIG_SYS_ISA_IO
CONFIG_SYS_ISA_IO_BASE_ADDRESS
-CONFIG_SYS_ISA_IO_OFFSET
-CONFIG_SYS_ISA_IO_STRIDE
CONFIG_SYS_ISA_MEM
CONFIG_SYS_JFFS2_FIRST_BANK
CONFIG_SYS_JFFS2_FIRST_SECTOR
@@ -3335,35 +3330,6 @@ CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
-CONFIG_SYS_NS87308_CS0_BASE
-CONFIG_SYS_NS87308_CS0_CONF
-CONFIG_SYS_NS87308_CS1_BASE
-CONFIG_SYS_NS87308_CS1_CONF
-CONFIG_SYS_NS87308_CS2_BASE
-CONFIG_SYS_NS87308_CS2_CONF
-CONFIG_SYS_NS87308_FDC
-CONFIG_SYS_NS87308_FDC_BASE
-CONFIG_SYS_NS87308_GPIO
-CONFIG_SYS_NS87308_GPIO_BASE
-CONFIG_SYS_NS87308_KBC1
-CONFIG_SYS_NS87308_KBC1_BASE
-CONFIG_SYS_NS87308_KBC2
-CONFIG_SYS_NS87308_LPT_BASE
-CONFIG_SYS_NS87308_MOUSE
-CONFIG_SYS_NS87308_PARP
-CONFIG_SYS_NS87308_PMC1
-CONFIG_SYS_NS87308_PMC2
-CONFIG_SYS_NS87308_PMC3
-CONFIG_SYS_NS87308_POWRMAN
-CONFIG_SYS_NS87308_PS2MOD
-CONFIG_SYS_NS87308_PWMAN_BASE
-CONFIG_SYS_NS87308_RARP
-CONFIG_SYS_NS87308_RTC_APC
-CONFIG_SYS_NS87308_RTC_BASE
-CONFIG_SYS_NS87308_UART1
-CONFIG_SYS_NS87308_UART1_BASE
-CONFIG_SYS_NS87308_UART2
-CONFIG_SYS_NS87308_UART2_BASE
CONFIG_SYS_NUM_ADDR_MAP
CONFIG_SYS_NUM_CPC
CONFIG_SYS_NUM_FM1_10GEC
This seems pretty old now. It has not been converted to driver model and is not used by any boards. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> --- README | 26 -- cmd/Kconfig | 5 - cmd/Makefile | 1 - cmd/fdc.c | 752 -------------------------------- drivers/misc/Makefile | 1 - drivers/misc/ns87308.c | 100 ----- drivers/serial/serial_ns16550.c | 7 +- include/common.h | 1 - include/ns87308.h | 233 ---------- scripts/config_whitelist.txt | 34 -- 10 files changed, 1 insertion(+), 1159 deletions(-) delete mode 100644 cmd/fdc.c delete mode 100644 drivers/misc/ns87308.c delete mode 100644 include/ns87308.h