@@ -62,6 +62,7 @@ enum {
SFP_S_FAIL,
SFP_S_WAIT,
SFP_S_INIT,
+ SFP_S_INIT_PHY,
SFP_S_INIT_TX_FAULT,
SFP_S_WAIT_LOS,
SFP_S_LINK_UP,
@@ -126,6 +127,7 @@ static const char * const sm_state_strings[] = {
[SFP_S_FAIL] = "fail",
[SFP_S_WAIT] = "wait",
[SFP_S_INIT] = "init",
+ [SFP_S_INIT_PHY] = "init_phy",
[SFP_S_INIT_TX_FAULT] = "init_tx_fault",
[SFP_S_WAIT_LOS] = "wait_los",
[SFP_S_LINK_UP] = "link_up",
@@ -180,6 +182,12 @@ static const enum gpiod_flags gpio_flags[] = {
#define N_FAULT_INIT 5
#define N_FAULT 5
+/* T_PHY_RETRY is the time interval between attempts to probe the PHY.
+ * R_PHY_RETRY is the number of attempts.
+ */
+#define T_PHY_RETRY msecs_to_jiffies(50)
+#define R_PHY_RETRY 12
+
/* SFP module presence detection is poor: the three MOD DEF signals are
* the same length on the PCB, which means it's possible for MOD DEF 0 to
* connect before the I2C bus on MOD DEF 1/2.
@@ -235,6 +243,7 @@ struct sfp {
unsigned char sm_dev_state;
unsigned short sm_state;
unsigned char sm_fault_retries;
+ unsigned char sm_phy_retries;
struct sfp_eeprom_id id;
unsigned int module_power_mW;
@@ -1416,10 +1425,8 @@ static int sfp_sm_probe_phy(struct sfp *sfp, bool is_c45)
int err;
phy = get_phy_device(sfp->i2c_mii, SFP_PHY_ADDR, is_c45);
- if (phy == ERR_PTR(-ENODEV)) {
- dev_info(sfp->dev, "no PHY detected\n");
- return 0;
- }
+ if (phy == ERR_PTR(-ENODEV))
+ return PTR_ERR(phy);
if (IS_ERR(phy)) {
dev_err(sfp->dev, "mdiobus scan returned %ld\n", PTR_ERR(phy));
return PTR_ERR(phy);
@@ -1867,6 +1874,7 @@ static void sfp_sm_module(struct sfp *sfp, unsigned int event)
static void sfp_sm_main(struct sfp *sfp, unsigned int event)
{
unsigned long timeout;
+ int ret;
/* Some events are global */
if (sfp->sm_state != SFP_S_DOWN &&
@@ -1940,22 +1948,39 @@ static void sfp_sm_main(struct sfp *sfp, unsigned int event)
sfp_sm_fault(sfp, SFP_S_INIT_TX_FAULT,
sfp->sm_fault_retries == N_FAULT_INIT);
} else if (event == SFP_E_TIMEOUT || event == SFP_E_TX_CLEAR) {
- init_done: /* TX_FAULT deasserted or we timed out with TX_FAULT
- * clear. Probe for the PHY and check the LOS state.
- */
- if (sfp_sm_probe_for_phy(sfp)) {
- sfp_sm_next(sfp, SFP_S_FAIL, 0);
- break;
- }
- if (sfp_module_start(sfp->sfp_bus)) {
- sfp_sm_next(sfp, SFP_S_FAIL, 0);
+ init_done:
+ sfp->sm_phy_retries = R_PHY_RETRY;
+ goto phy_probe;
+ }
+ break;
+
+ case SFP_S_INIT_PHY:
+ if (event != SFP_E_TIMEOUT)
+ break;
+ phy_probe:
+ /* TX_FAULT deasserted or we timed out with TX_FAULT
+ * clear. Probe for the PHY and check the LOS state.
+ */
+ ret = sfp_sm_probe_for_phy(sfp);
+ if (ret == -ENODEV) {
+ if (--sfp->sm_phy_retries) {
+ sfp_sm_next(sfp, SFP_S_INIT_PHY, T_PHY_RETRY);
break;
+ } else {
+ dev_info(sfp->dev, "no PHY detected\n");
}
- sfp_sm_link_check_los(sfp);
-
- /* Reset the fault retry count */
- sfp->sm_fault_retries = N_FAULT;
+ } else if (ret) {
+ sfp_sm_next(sfp, SFP_S_FAIL, 0);
+ break;
}
+ if (sfp_module_start(sfp->sfp_bus)) {
+ sfp_sm_next(sfp, SFP_S_FAIL, 0);
+ break;
+ }
+ sfp_sm_link_check_los(sfp);
+
+ /* Reset the fault retry count */
+ sfp->sm_fault_retries = N_FAULT;
break;
case SFP_S_INIT_TX_FAULT:
Some 1000BASE-T PHY modules take a while for the PHY to wake up. Retry the probe a number of times before deciding that the module has no PHY. Tested with: Sourcephotonics SPGBTXCNFC - PHY takes less than 50ms to respond. Champion One 1000SFPT - PHY takes about 200ms to respond. Mikrotik S-RJ01 - no PHY Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> --- drivers/net/phy/sfp.c | 59 ++++++++++++++++++++++++++++++------------- 1 file changed, 42 insertions(+), 17 deletions(-)