[v2,3/3] dt-bindings: phy: qcom-qusb2: Add SC7180 QUSB2 phy support
diff mbox series

Message ID 1575520881-31458-4-git-send-email-sanm@codeaurora.org
State Changes Requested
Headers show
Series
  • Add QUSB2 PHY support for SC7180
Related show

Checks

Context Check Description
robh/checkpatch success

Commit Message

Sandeep Maheswaram Dec. 5, 2019, 4:41 a.m. UTC
Add QUSB2 phy entries for SC7180 in device tree bindings.

Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
---
 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

Comments

Douglas Anderson Dec. 18, 2019, 7:09 p.m. UTC | #1
Hi,

On Wed, Dec 4, 2019 at 8:43 PM Sandeep Maheswaram <sanm@codeaurora.org> wrote:
>
> Add QUSB2 phy entries for SC7180 in device tree bindings.
>
> Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
> ---
>  Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml | 9 +++++----
>  1 file changed, 5 insertions(+), 4 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
> index 3ef94bc..5eff9016 100644
> --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
> @@ -18,6 +18,7 @@ properties:
>      enum:
>        - qcom,msm8996-qusb2-phy
>        - qcom,msm8998-qusb2-phy
> +      - qcom,sc7180-qusb2-phy
>        - qcom,sdm845-qusb2-phy

I would propose that we add generic PHY v2 tagging here, like this:

properties:
  compatible:
    anyOf:
      - items:
        - const: qcom,msm8996-qusb2-phy
      - items:
        - const: qcom,msm8998-qusb2-phy
      - items:
        # Suggested to also add "qcom,qusb2-v2-phy" as below.
        - const: qcom,sdm845-qusb2-phy
      - items:
        - enum:
          - qcom,sc7180-qusb2-phy
          - qcom,sdm845-qusb2-phy
        - const: qcom,qusb2-v2-phy

Given that this PHY has a fairly linear versioning within Qualcomm
(right?) this should make sense and should make code / adding new
device trees easier.  This is probably better than what I suggested in
the driver review [1] where I suggested that the compatible for sc7180
should be:

  compatible: "qcom,sc7180-qusb2-phy", "qcom,sdm845-qusb2-phy"


>    reg:
> @@ -66,7 +67,7 @@ properties:
>          It is a 6 bit value that specifies offset to be
>          added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
>          tuning parameter that may vary for different boards of same SOC.
> -        This property is applicable to only QUSB2 v2 PHY (sdm845).
> +        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).

If you add my tagging, change this and other similar to just remove sdm845.


[1] https://lore.kernel.org/r/CAD=FV=W_z=_j==DSFbtCmTihmSyRtH85VnKpw03E=gATcqJx2Q@mail.gmail.com

-Doug

Patch
diff mbox series

diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
index 3ef94bc..5eff9016 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
@@ -18,6 +18,7 @@  properties:
     enum:
       - qcom,msm8996-qusb2-phy
       - qcom,msm8998-qusb2-phy
+      - qcom,sc7180-qusb2-phy
       - qcom,sdm845-qusb2-phy
 
   reg:
@@ -66,7 +67,7 @@  properties:
         It is a 6 bit value that specifies offset to be
         added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
         tuning parameter that may vary for different boards of same SOC.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
     $ref: /schemas/types.yaml#/definitions/uint32
 
   qcom,hstx-trim-value:
@@ -75,7 +76,7 @@  properties:
         output current.
         Possible range is - 15mA to 24mA (stepsize of 600 uA).
         See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
         Default value is 22.2mA for sdm845.
     $ref: /schemas/types.yaml#/definitions/uint32
 
@@ -84,7 +85,7 @@  properties:
         It is a 2 bit value that specifies pre-emphasis level.
         Possible range is 0 to 15% (stepsize of 5%).
         See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
         Default value is 10% for sdm845.
     $ref: /schemas/types.yaml#/definitions/uint32
 
@@ -94,7 +95,7 @@  properties:
         pre-emphasis (specified using qcom,preemphasis-level) must be in
         effect. Duration could be half-bit of full-bit.
         See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
         Default value is full-bit width for sdm845.
     $ref: /schemas/types.yaml#/definitions/uint32