[v5,1/2] pinctrl: Add pinmux & GPIO controller driver for a new SoC
diff mbox series

Message ID 890db37db56e7e49e83b9fa03903bf3482c624c7.1573196057.git.rahul.tanwar@linux.intel.com
State New
Headers show
Series
  • pinctrl: Add new pinctrl/GPIO driver
Related show

Commit Message

Rahul Tanwar Nov. 8, 2019, 9:42 a.m. UTC
Intel Lightning Mountain SoC has a pinmux controller & GPIO controller IP which
controls pin multiplexing & configuration including GPIO functions selection &
GPIO attributes configuration.

This IP is not based on & does not have anything in common with Chassis
specification. The pinctrl drivers under pinctrl/intel/* are all based upon
Chassis spec compliant pinctrl IPs. So this driver doesn't fit & can not use
pinctrl framework under pinctrl/intel/* and it requires a separate new driver.

Add a new GPIO & pin control framework based driver for this IP.

Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
---
 drivers/pinctrl/Kconfig               |  18 +
 drivers/pinctrl/Makefile              |   1 +
 drivers/pinctrl/pinctrl-equilibrium.c | 962 ++++++++++++++++++++++++++++++++++
 drivers/pinctrl/pinctrl-equilibrium.h | 144 +++++
 4 files changed, 1125 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-equilibrium.c
 create mode 100644 drivers/pinctrl/pinctrl-equilibrium.h

Comments

Andy Shevchenko Nov. 8, 2019, 11:40 a.m. UTC | #1
On Fri, Nov 08, 2019 at 05:42:22PM +0800, Rahul Tanwar wrote:
> Intel Lightning Mountain SoC has a pinmux controller & GPIO controller IP which
> controls pin multiplexing & configuration including GPIO functions selection &
> GPIO attributes configuration.
> 
> This IP is not based on & does not have anything in common with Chassis
> specification. The pinctrl drivers under pinctrl/intel/* are all based upon
> Chassis spec compliant pinctrl IPs. So this driver doesn't fit & can not use
> pinctrl framework under pinctrl/intel/* and it requires a separate new driver.
> 
> Add a new GPIO & pin control framework based driver for this IP.

> +static void eqbr_gpio_enable_irq(struct irq_data *d)
> +{
> +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> +	struct eqbr_gpio_ctrl *gctrl = gpiochip_get_data(gc);
> +	unsigned int offset = irqd_to_hwirq(d);
> +	unsigned long flags;
> +

> +	gc->direction_input(gc, offset);

Does this any IO?
If so, between above and below a window of possible race.
Ditto for all other functions that do something similar.

> +	raw_spin_lock_irqsave(&gctrl->lock, flags);
> +	writel(BIT(offset), gctrl->membase + GPIO_IRNRNSET);
> +	raw_spin_unlock_irqrestore(&gctrl->lock, flags);
> +}

> +		ret = bgpio_init(&gctrl->chip, dev, gctrl->bank->nr_pins / 8,
> +				 gctrl->membase + GPIO_IN,
> +				 gctrl->membase + GPIO_OUTSET,
> +				 gctrl->membase + GPIO_OUTCLR,
> +				 gctrl->membase + GPIO_DIR,

> +				 NULL,
> +				 0);

One line?

> +static int get_drv_cur(void __iomem *mem, unsigned int offset)
> +{
> +	unsigned int idx = offset / DRV_CUR_PINS; /* 0-15, 16-31 per register*/
> +	unsigned int val;
> +
> +	val = readl(mem + REG_DRCC(idx));

> +	offset %= DRV_CUR_PINS;

From style point of view is better to have
	... foo = offset / X;
	... bar = offset % X;

directly in definition block. Moreover, for example, on x86 it might be
converted by compiler to single idiv call in assembly that returns in
(eax, edx) both values at once.

> +	val = PARSE_DRV_CURRENT(val, offset);
> +
> +	return val;
> +}

> +	if (!(bank->aval_pinmap & BIT(offset))) {
> +		dev_err(pctl->dev,
> +			"PIN: %u is not valid, pinbase: %u, bitmap: %u\n",
> +			pin, bank->pin_base, bank->aval_pinmap);
> +		return -ENODEV;
> +	}

Looks like aval_pinmap is NIH of valid_mask bitmap in GPIO library.
Can you check if it suits your purposes?

> +static bool is_func_exist(struct eqbr_pmx_func *funcs, const char *name,
> +			 unsigned int nr_funcs, unsigned int *idx)
> +{
> +	int i;
> +

> +	if (!funcs || !nr_funcs)
> +		return false;

nr_funcs check is a dup of the one in for loop.

> +	for (i = 0; i < nr_funcs; i++) {

> +		if (funcs[i].name && (strcmp(funcs[i].name, name) == 0) ) {

An extra space, but you may use !strcmp() and make it shorter without redundant
parentheses.

> +			*idx = i;
> +			return true;
> +		}
> +	}
> +
> +	return false;
> +}

> +		switch (op) {
> +			case OP_COUNT_NR_FUNCS:

case goes usually on the same column as switch.

> +				if (!is_func_exist(funcs, fn_name,
> +						   *nr_funcs, &fid))
> +					*nr_funcs = *nr_funcs + 1;
> +				break;
> +
> +			case OP_ADD_FUNCS:
> +				if (!is_func_exist(funcs, fn_name,
> +						   *nr_funcs, &fid))
> +					funcs[i].name = fn_name;
> +				break;
> +
> +			case OP_COUNT_NR_FUNC_GRPS:
> +				if (is_func_exist(funcs, fn_name,
> +						  *nr_funcs, &fid))
> +					funcs[fid].nr_groups++;
> +				break;
> +
> +			case OP_ADD_FUNC_GRPS:
> +				if (is_func_exist(funcs, fn_name,
> +						  *nr_funcs, &fid)) {

> +					for(j=0;

Other style issueS.

> +					    j < funcs[fid].nr_groups;
> +					    j++) {
> +						if (!funcs[fid].groups[j])
> +							break;
> +					}
> +					funcs[fid].groups[j] = prop->value;
> +				}
> +				break;
> +
> +			default:
> +				return -EINVAL;

> +

Redundant blank line.

> +		}

> +	for (i = 0; i < nr_funcs; i++) {
> +		if (funcs[i].nr_groups) {

	if (!foo)
		continue;
?

> +			funcs[i].groups = devm_kcalloc(dev, funcs[i].nr_groups,
> +						       sizeof(*(funcs[i].groups)),
> +						       GFP_KERNEL);
> +			if (!funcs[i].groups)
> +				return -ENOMEM;
> +		}
> +	}
Rahul Tanwar Nov. 11, 2019, 5:59 a.m. UTC | #2
Hi Andy,

On 8/11/2019 7:40 PM, Andy Shevchenko wrote:
> On Fri, Nov 08, 2019 at 05:42:22PM +0800, Rahul Tanwar wrote:
>> Intel Lightning Mountain SoC has a pinmux controller & GPIO controller IP which
>> controls pin multiplexing & configuration including GPIO functions selection &
>> GPIO attributes configuration.
>>
>> This IP is not based on & does not have anything in common with Chassis
>> specification. The pinctrl drivers under pinctrl/intel/* are all based upon
>> Chassis spec compliant pinctrl IPs. So this driver doesn't fit & can not use
>> pinctrl framework under pinctrl/intel/* and it requires a separate new driver.
>>
>> Add a new GPIO & pin control framework based driver for this IP.
>> +static void eqbr_gpio_enable_irq(struct irq_data *d)
>> +{
>> +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
>> +	struct eqbr_gpio_ctrl *gctrl = gpiochip_get_data(gc);
>> +	unsigned int offset = irqd_to_hwirq(d);
>> +	unsigned long flags;
>> +
>> +	gc->direction_input(gc, offset);
> Does this any IO?
> If so, between above and below a window of possible race.
> Ditto for all other functions that do something similar.

gpio-mmio lib uses its own spin lock when it does IO in gc->direction_input()
And that would set pin direction as input (hw ensures that the pin is not
driven high when set direction) while below will enable interrupton that
pin. I do not see any possible race condition in that..

>> +	raw_spin_lock_irqsave(&gctrl->lock, flags);
>> +	writel(BIT(offset), gctrl->membase + GPIO_IRNRNSET);
>> +	raw_spin_unlock_irqrestore(&gctrl->lock, flags);
>> +}
>> +		ret = bgpio_init(&gctrl->chip, dev, gctrl->bank->nr_pins / 8,
>> +				 gctrl->membase + GPIO_IN,
>> +				 gctrl->membase + GPIO_OUTSET,
>> +				 gctrl->membase + GPIO_OUTCLR,
>> +				 gctrl->membase + GPIO_DIR,
>> +				 NULL,
>> +				 0);
> One line?

Sure, missed it.

>> +static int get_drv_cur(void __iomem *mem, unsigned int offset)
>> +{
>> +	unsigned int idx = offset / DRV_CUR_PINS; /* 0-15, 16-31 per register*/
>> +	unsigned int val;
>> +
>> +	val = readl(mem + REG_DRCC(idx));
>> +	offset %= DRV_CUR_PINS;
> From style point of view is better to have
> 	... foo = offset / X;
> 	... bar = offset % X;
>
> directly in definition block. Moreover, for example, on x86 it might be
> converted by compiler to single idiv call in assembly that returns in
> (eax, edx) both values at once.

Ok, i will change it like that but will have to introduce one more variable.

>> +	val = PARSE_DRV_CURRENT(val, offset);
>> +
>> +	return val;
>> +}
>> +	if (!(bank->aval_pinmap & BIT(offset))) {
>> +		dev_err(pctl->dev,
>> +			"PIN: %u is not valid, pinbase: %u, bitmap: %u\n",
>> +			pin, bank->pin_base, bank->aval_pinmap);
>> +		return -ENODEV;
>> +	}
> Looks like aval_pinmap is NIH of valid_mask bitmap in GPIO library.
> Can you check if it suits your purposes?

I did check about it earlier & now as well. It doesn't suit our purpose.
aval_pinmapin the driver indicates whether pad control of this pad is
available or not. It's for all pins irrespective of if it is used as a
gpio or not. Whereas, valid_mask bitmap of GPIO library is just to
indicate if that gpio line is valid or not. valid_mask would have been
useful if this driver was purely a GPIO driver.

>> +static bool is_func_exist(struct eqbr_pmx_func *funcs, const char *name,
>> +			 unsigned int nr_funcs, unsigned int *idx)
>> +{
>> +	int i;
>> +
>> +	if (!funcs || !nr_funcs)
>> +		return false;
> nr_funcs check is a dup of the one in for loop.

Sure, noted.

>> +	for (i = 0; i < nr_funcs; i++) {
>> +		if (funcs[i].name && (strcmp(funcs[i].name, name) == 0) ) {
> An extra space, but you may use !strcmp() and make it shorter without redundant
> parentheses.

Well noted, thanks.

>> +			*idx = i;
>> +			return true;
>> +		}
>> +	}
>> +
>> +	return false;
>> +}
>> +		switch (op) {
>> +			case OP_COUNT_NR_FUNCS:
> case goes usually on the same column as switch.

Sure, will change, didn't know about it. Thanks.

>> +				if (!is_func_exist(funcs, fn_name,
>> +						   *nr_funcs, &fid))
>> +					*nr_funcs = *nr_funcs + 1;
>> +				break;
>> +
>> +			case OP_ADD_FUNCS:
>> +				if (!is_func_exist(funcs, fn_name,
>> +						   *nr_funcs, &fid))
>> +					funcs[i].name = fn_name;
>> +				break;
>> +
>> +			case OP_COUNT_NR_FUNC_GRPS:
>> +				if (is_func_exist(funcs, fn_name,
>> +						  *nr_funcs, &fid))
>> +					funcs[fid].nr_groups++;
>> +				break;
>> +
>> +			case OP_ADD_FUNC_GRPS:
>> +				if (is_func_exist(funcs, fn_name,
>> +						  *nr_funcs, &fid)) {
>> +					for(j=0;
> Other style issueS.

Will fix in v6, thanks.

>> +		}
>> +	for (i = 0; i < nr_funcs; i++) {
>> +		if (funcs[i].nr_groups) {
> 	if (!foo)
> 		continue;
> ?

Sure, will change. Thanks.

Regards,
Rahul

Patch
diff mbox series

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index b372419d61f2..7809e33c7762 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -420,4 +420,22 @@  config PINCTRL_TB10X
 	depends on OF && ARC_PLAT_TB10X
 	select GPIOLIB
 
+config PINCTRL_EQUILIBRIUM
+	tristate "Generic pinctrl and GPIO driver for Intel Lightning Mountain SoC"
+	select PINMUX
+	select PINCONF
+	select GPIOLIB
+	select GPIO_GENERIC
+	select GPIOLIB_IRQCHIP
+	select GENERIC_PINCONF
+	select GENERIC_PINCTRL_GROUPS
+	select GENERIC_PINMUX_FUNCTIONS
+
+	help
+	  Equilibrium pinctrl driver is a pinctrl & GPIO driver for Intel Lightning
+	  Mountain network processor SoC that supports both the linux GPIO and pin
+	  control frameworks. It provides interfaces to setup pinmux, assign desired
+	  pin functions, configure GPIO attributes for LGM SoC pins. Pinmux and
+	  pinconf settings are retrieved from device tree.
+
 endif
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index ac537fdbc998..879f312bfb75 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -46,6 +46,7 @@  obj-$(CONFIG_PINCTRL_ZYNQ)	+= pinctrl-zynq.o
 obj-$(CONFIG_PINCTRL_INGENIC)	+= pinctrl-ingenic.o
 obj-$(CONFIG_PINCTRL_RK805)	+= pinctrl-rk805.o
 obj-$(CONFIG_PINCTRL_OCELOT)	+= pinctrl-ocelot.o
+obj-$(CONFIG_PINCTRL_EQUILIBRIUM)   += pinctrl-equilibrium.o
 
 obj-y				+= actions/
 obj-$(CONFIG_ARCH_ASPEED)	+= aspeed/
diff --git a/drivers/pinctrl/pinctrl-equilibrium.c b/drivers/pinctrl/pinctrl-equilibrium.c
new file mode 100644
index 000000000000..441f8bae580b
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-equilibrium.c
@@ -0,0 +1,962 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (C) 2019 Intel Corporation */
+
+#include <linux/gpio/driver.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+
+#include "core.h"
+#include "pinconf.h"
+#include "pinmux.h"
+#include "pinctrl-equilibrium.h"
+
+#define PIN_NAME_FMT	"io-%d"
+#define PIN_NAME_LEN	10
+#define PAD_REG_OFF	0x100
+
+static void eqbr_gpio_disable_irq(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct eqbr_gpio_ctrl *gctrl = gpiochip_get_data(gc);
+	unsigned int offset = irqd_to_hwirq(d);
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&gctrl->lock, flags);
+	writel(BIT(offset), gctrl->membase + GPIO_IRNENCLR);
+	raw_spin_unlock_irqrestore(&gctrl->lock, flags);
+}
+
+static void eqbr_gpio_enable_irq(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct eqbr_gpio_ctrl *gctrl = gpiochip_get_data(gc);
+	unsigned int offset = irqd_to_hwirq(d);
+	unsigned long flags;
+
+	gc->direction_input(gc, offset);
+	raw_spin_lock_irqsave(&gctrl->lock, flags);
+	writel(BIT(offset), gctrl->membase + GPIO_IRNRNSET);
+	raw_spin_unlock_irqrestore(&gctrl->lock, flags);
+}
+
+static void eqbr_gpio_ack_irq(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct eqbr_gpio_ctrl *gctrl = gpiochip_get_data(gc);
+	unsigned int offset = irqd_to_hwirq(d);
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&gctrl->lock, flags);
+	writel(BIT(offset), gctrl->membase + GPIO_IRNCR);
+	raw_spin_unlock_irqrestore(&gctrl->lock, flags);
+}
+
+static void eqbr_gpio_mask_ack_irq(struct irq_data *d)
+{
+	eqbr_gpio_disable_irq(d);
+	eqbr_gpio_ack_irq(d);
+}
+
+static inline void eqbr_cfg_bit(void __iomem *addr,
+				unsigned int offset, unsigned int set)
+{
+	if (set)
+		writel(readl(addr) | BIT(offset), addr);
+	else
+		writel(readl(addr) & ~BIT(offset), addr);
+}
+
+static int eqbr_irq_type_cfg(struct gpio_irq_type *type,
+			     struct eqbr_gpio_ctrl *gctrl,
+			     unsigned int offset)
+{
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&gctrl->lock, flags);
+	eqbr_cfg_bit(gctrl->membase + GPIO_IRNCFG, offset, type->trig_type);
+	eqbr_cfg_bit(gctrl->membase + GPIO_EXINTCR1, offset, type->trig_type);
+	eqbr_cfg_bit(gctrl->membase + GPIO_EXINTCR0, offset, type->logic_type);
+	raw_spin_unlock_irqrestore(&gctrl->lock, flags);
+
+	return 0;
+}
+
+static int eqbr_gpio_set_irq_type(struct irq_data *d, unsigned int type)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct eqbr_gpio_ctrl *gctrl = gpiochip_get_data(gc);
+	unsigned int offset = irqd_to_hwirq(d);
+	struct gpio_irq_type it;
+
+	memset(&it, 0, sizeof(it));
+
+	if ((type & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_NONE)
+		return 0;
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		it.trig_type = GPIO_EDGE_TRIG;
+		it.edge_type = GPIO_SINGLE_EDGE;
+		it.logic_type = GPIO_POSITIVE_TRIG;
+		break;
+
+	case IRQ_TYPE_EDGE_FALLING:
+		it.trig_type = GPIO_EDGE_TRIG;
+		it.edge_type = GPIO_SINGLE_EDGE;
+		it.logic_type = GPIO_NEGATIVE_TRIG;
+		break;
+
+	case IRQ_TYPE_EDGE_BOTH:
+		it.trig_type = GPIO_EDGE_TRIG;
+		it.edge_type = GPIO_BOTH_EDGE;
+		it.logic_type = GPIO_POSITIVE_TRIG;
+		break;
+
+	case IRQ_TYPE_LEVEL_HIGH:
+		it.trig_type = GPIO_LEVEL_TRIG;
+		it.edge_type = GPIO_SINGLE_EDGE;
+		it.logic_type = GPIO_POSITIVE_TRIG;
+		break;
+
+	case IRQ_TYPE_LEVEL_LOW:
+		it.trig_type = GPIO_LEVEL_TRIG;
+		it.edge_type = GPIO_SINGLE_EDGE;
+		it.logic_type = GPIO_NEGATIVE_TRIG;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	eqbr_irq_type_cfg(&it, gctrl, offset);
+	if (it.trig_type == GPIO_EDGE_TRIG)
+		irq_set_handler_locked(d, handle_edge_irq);
+	else
+		irq_set_handler_locked(d, handle_level_irq);
+
+	return 0;
+}
+
+static void eqbr_irq_handler(struct irq_desc *desc)
+{
+	struct gpio_chip *gc = irq_desc_get_handler_data(desc);
+	struct eqbr_gpio_ctrl *gctrl = gpiochip_get_data(gc);
+	struct irq_chip *ic = irq_desc_get_chip(desc);
+	unsigned long pins, offset;
+
+	chained_irq_enter(ic, desc);
+	pins = readl(gctrl->membase + GPIO_IRNCR);
+
+	for_each_set_bit(offset, &pins, gc->ngpio)
+		generic_handle_irq(irq_find_mapping(gc->irq.domain, offset));
+
+	chained_irq_exit(ic, desc);
+}
+
+static int gpiochip_setup(struct device *dev, struct eqbr_gpio_ctrl *gctrl)
+{
+	struct gpio_irq_chip *girq;
+	struct gpio_chip *gc;
+
+	gc = &gctrl->chip;
+	gc->label = gctrl->name;
+#if defined(CONFIG_OF_GPIO)
+	gc->of_node = gctrl->node;
+#endif
+
+	if (!of_property_read_bool(gctrl->node, "interrupt-controller")) {
+		dev_dbg(dev, "gc %s: doesn't act as interrupt controller!\n",
+			gctrl->name);
+		return 0;
+	}
+
+	gctrl->ic.name = "gpio_irq";
+	gctrl->ic.irq_mask = eqbr_gpio_disable_irq;
+	gctrl->ic.irq_unmask = eqbr_gpio_enable_irq;
+	gctrl->ic.irq_ack = eqbr_gpio_ack_irq;
+	gctrl->ic.irq_mask_ack = eqbr_gpio_mask_ack_irq;
+	gctrl->ic.irq_set_type = eqbr_gpio_set_irq_type;
+
+	girq = &gctrl->chip.irq;
+	girq->chip = &gctrl->ic;
+	girq->parent_handler = eqbr_irq_handler;
+	girq->num_parents = 1;
+	girq->parents = devm_kcalloc(dev, 1, sizeof(*girq->parents), GFP_KERNEL);
+	if (!girq->parents)
+		return -ENOMEM;
+
+	girq->default_type = IRQ_TYPE_NONE;
+	girq->handler = handle_bad_irq;
+	girq->parents[0] = gctrl->virq;
+
+	return 0;
+}
+
+static int gpiolib_reg(struct eqbr_pinctrl_drv_data *drvdata)
+{
+	struct device *dev = drvdata->dev;
+	struct eqbr_gpio_ctrl *gctrl;
+	struct device_node *np;
+	struct resource res;
+	int i, ret;
+
+	for (i = 0; i < drvdata->nr_gpio_ctrls; i++) {
+		gctrl = drvdata->gpio_ctrls + i;
+		np = gctrl->node;
+
+		gctrl->name = devm_kasprintf(dev, GFP_KERNEL, "gpiochip%d", i);
+		if (!gctrl->name)
+			return -ENOMEM;
+
+		if (of_address_to_resource(np, 0, &res)) {
+			dev_err(dev, "Failed to get GPIO register address\n");
+			return -ENXIO;
+		}
+
+		gctrl->membase = devm_ioremap_resource(dev, &res);
+		if (IS_ERR(gctrl->membase))
+			return PTR_ERR(gctrl->membase);
+
+		gctrl->virq = irq_of_parse_and_map(np, 0);
+		if (!gctrl->virq) {
+			dev_err(dev, "%s: failed to parse and map irq\n",
+				gctrl->name);
+			return -ENXIO;
+		}
+		raw_spin_lock_init(&gctrl->lock);
+
+		ret = bgpio_init(&gctrl->chip, dev, gctrl->bank->nr_pins / 8,
+				 gctrl->membase + GPIO_IN,
+				 gctrl->membase + GPIO_OUTSET,
+				 gctrl->membase + GPIO_OUTCLR,
+				 gctrl->membase + GPIO_DIR,
+				 NULL,
+				 0);
+		if (ret) {
+			dev_err(dev, "unable to init generic GPIO\n");
+			return ret;
+		}
+
+		ret = gpiochip_setup(dev, gctrl);
+		if (ret)
+			return ret;
+
+		ret = devm_gpiochip_add_data(dev, &gctrl->chip, gctrl);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static inline struct eqbr_pin_bank
+*find_pinbank_via_pin(struct eqbr_pinctrl_drv_data *pctl, unsigned int pin)
+{
+	struct eqbr_pin_bank *bank;
+	int i;
+
+	for (i = 0; i < pctl->nr_banks; i++) {
+		bank = &pctl->pin_banks[i];
+		if (pin >= bank->pin_base &&
+		    (pin - bank->pin_base) < bank->nr_pins)
+			return bank;
+	}
+
+	return NULL;
+}
+
+static const struct pinctrl_ops eqbr_pctl_ops = {
+	.get_groups_count	= pinctrl_generic_get_group_count,
+	.get_group_name		= pinctrl_generic_get_group_name,
+	.get_group_pins		= pinctrl_generic_get_group_pins,
+	.dt_node_to_map		= pinconf_generic_dt_node_to_map_all,
+	.dt_free_map		= pinconf_generic_dt_free_map,
+};
+
+static int eqbr_set_pin_mux(struct eqbr_pinctrl_drv_data *pctl,
+			    unsigned int pmx, unsigned int pin)
+{
+	struct eqbr_pin_bank *bank;
+	unsigned long flags;
+	unsigned int offset;
+	void __iomem *mem;
+
+	bank = find_pinbank_via_pin(pctl, pin);
+	if (!bank) {
+		dev_err(pctl->dev, "Couldn't find pin bank for pin %u\n", pin);
+		return -ENODEV;
+	}
+	mem = bank->membase;
+	offset = pin - bank->pin_base;
+
+	if (!(bank->aval_pinmap & BIT(offset))) {
+		dev_err(pctl->dev,
+			"PIN: %u is not valid, pinbase: %u, bitmap: %u\n",
+			pin, bank->pin_base, bank->aval_pinmap);
+		return -ENODEV;
+	}
+
+	raw_spin_lock_irqsave(&pctl->lock, flags);
+	writel(pmx, mem + (offset << 2));
+	raw_spin_unlock_irqrestore(&pctl->lock, flags);
+	return 0;
+}
+
+static int eqbr_pinmux_set_mux(struct pinctrl_dev *pctldev,
+			       unsigned int selector, unsigned int group)
+{
+	struct eqbr_pinctrl_drv_data *pctl = pinctrl_dev_get_drvdata(pctldev);
+	struct function_desc *func;
+	struct group_desc *grp;
+	unsigned int *pinmux;
+	int i;
+
+	func = pinmux_generic_get_function(pctldev, selector);
+	if (!func)
+		return -EINVAL;
+
+	grp = pinctrl_generic_get_group(pctldev, group);
+	if (!grp)
+		return -EINVAL;
+
+	pinmux = grp->data;
+	for (i = 0; i < grp->num_pins; i++)
+		eqbr_set_pin_mux(pctl, pinmux[i], grp->pins[i]);
+
+	return 0;
+}
+
+static int eqbr_pinmux_gpio_request(struct pinctrl_dev *pctldev,
+				    struct pinctrl_gpio_range *range,
+				    unsigned int pin)
+{
+	struct eqbr_pinctrl_drv_data *pctl = pinctrl_dev_get_drvdata(pctldev);
+
+	return eqbr_set_pin_mux(pctl, EQBR_GPIO_MODE, pin);
+}
+
+static const struct pinmux_ops eqbr_pinmux_ops = {
+	.get_functions_count	= pinmux_generic_get_function_count,
+	.get_function_name	= pinmux_generic_get_function_name,
+	.get_function_groups	= pinmux_generic_get_function_groups,
+	.set_mux		= eqbr_pinmux_set_mux,
+	.gpio_request_enable	= eqbr_pinmux_gpio_request,
+	.strict			= true,
+};
+
+static int get_drv_cur(void __iomem *mem, unsigned int offset)
+{
+	unsigned int idx = offset / DRV_CUR_PINS; /* 0-15, 16-31 per register*/
+	unsigned int val;
+
+	val = readl(mem + REG_DRCC(idx));
+	offset %= DRV_CUR_PINS;
+	val = PARSE_DRV_CURRENT(val, offset);
+
+	return val;
+}
+
+static struct eqbr_gpio_ctrl
+*get_gpio_ctrls_via_bank(struct eqbr_pinctrl_drv_data *pctl,
+			struct eqbr_pin_bank *bank)
+{
+	int i;
+
+	for (i = 0; i < pctl->nr_gpio_ctrls; i++) {
+		if (pctl->gpio_ctrls[i].bank == bank)
+			return &pctl->gpio_ctrls[i];
+	}
+
+	return NULL;
+}
+
+static int eqbr_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin,
+			    unsigned long *config)
+{
+	struct eqbr_pinctrl_drv_data *pctl = pinctrl_dev_get_drvdata(pctldev);
+	enum pin_config_param param = pinconf_to_config_param(*config);
+	struct eqbr_gpio_ctrl *gctrl;
+	struct eqbr_pin_bank *bank;
+	unsigned long flags;
+	unsigned int offset;
+	void __iomem *mem;
+	u32 val;
+
+	bank = find_pinbank_via_pin(pctl, pin);
+	if (!bank) {
+		dev_err(pctl->dev, "Couldn't find pin bank for pin %u\n", pin);
+		return -ENODEV;
+	}
+	mem = bank->membase;
+	offset = pin - bank->pin_base;
+
+	if (!(bank->aval_pinmap & BIT(offset))) {
+		dev_err(pctl->dev,
+			"PIN: %u is not valid, pinbase: %u, bitmap: %u\n",
+			pin, bank->pin_base, bank->aval_pinmap);
+		return -ENODEV;
+	}
+
+	raw_spin_lock_irqsave(&pctl->lock, flags);
+	switch (param) {
+	case PIN_CONFIG_BIAS_PULL_UP:
+		val = !!(readl(mem + REG_PUEN) & BIT(offset));
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		val = !!(readl(mem + REG_PDEN) & BIT(offset));
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		val = !!(readl(mem + REG_OD) & BIT(offset));
+		break;
+	case PIN_CONFIG_DRIVE_STRENGTH:
+		val = get_drv_cur(mem, offset);
+		break;
+	case PIN_CONFIG_SLEW_RATE:
+		val = !!(readl(mem + REG_SRC) & BIT(offset));
+		break;
+	case PIN_CONFIG_OUTPUT_ENABLE:
+		gctrl = get_gpio_ctrls_via_bank(pctl, bank);
+		if (!gctrl) {
+			dev_err(pctl->dev, "Failed to find gpio via bank pinbase: %u, pin: %u\n",
+				bank->pin_base, pin);
+			raw_spin_unlock_irqrestore(&pctl->lock, flags);
+			return -ENODEV;
+		}
+		val = !!(readl(gctrl->membase + GPIO_DIR) & BIT(offset));
+		break;
+	default:
+		raw_spin_unlock_irqrestore(&pctl->lock, flags);
+		return -ENOTSUPP;
+	}
+	raw_spin_unlock_irqrestore(&pctl->lock, flags);
+	*config = pinconf_to_config_packed(param, val);
+;
+	return 0;
+}
+
+static int eqbr_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
+			    unsigned long *configs, unsigned int num_configs)
+{
+	struct eqbr_pinctrl_drv_data *pctl = pinctrl_dev_get_drvdata(pctldev);
+	struct eqbr_gpio_ctrl *gctrl;
+	enum pin_config_param param;
+	struct eqbr_pin_bank *bank;
+	unsigned int val, offset;
+	struct gpio_chip *gc;
+	unsigned long flags;
+	void __iomem *mem;
+	u32 regval, mask;
+	int i;
+
+	for (i = 0; i < num_configs; i++) {
+		param = pinconf_to_config_param(configs[i]);
+		val = pinconf_to_config_argument(configs[i]);
+
+		bank = find_pinbank_via_pin(pctl, pin);
+		if (!bank) {
+			dev_err(pctl->dev,
+				"Couldn't find pin bank for pin %u\n", pin);
+			return -ENODEV;
+		}
+		mem = bank->membase;
+		offset = pin - bank->pin_base;
+
+		switch (param) {
+		case PIN_CONFIG_BIAS_PULL_UP:
+			mem += REG_PUEN;
+			val &= 0x1;
+			mask = BIT(offset);
+			break;
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			mem += REG_PDEN;
+			val &= 0x1;
+			mask = BIT(offset);
+			break;
+		case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+			mem += REG_OD;
+			val &= 0x1;
+			mask = BIT(offset);
+			break;
+		case PIN_CONFIG_DRIVE_STRENGTH:
+			mem += REG_DRCC(offset / DRV_CUR_PINS);
+			offset = (offset % DRV_CUR_PINS) << 1;
+			val &= 0x3;
+			mask = GENMASK(offset + 1, offset);
+			break;
+		case PIN_CONFIG_SLEW_RATE:
+			mem += REG_SRC;
+			val &= 0x1;
+			mask = BIT(offset);
+			break;
+		case PIN_CONFIG_OUTPUT_ENABLE:
+			gctrl = get_gpio_ctrls_via_bank(pctl, bank);
+			if (!gctrl) {
+				dev_err(pctl->dev, "Failed to find gpio via bank pinbase: %u, pin: %u\n",
+					bank->pin_base, pin);
+				return -ENODEV;
+			}
+			gc = &gctrl->chip;
+			gc->direction_output(gc, offset, 0);
+			continue;
+		default:
+			return -ENOTSUPP;
+		}
+
+		raw_spin_lock_irqsave(&pctl->lock, flags);
+		regval = readl(mem);
+		regval = (regval & ~mask) | (val << offset);
+		writel(regval, mem);
+		raw_spin_unlock_irqrestore(&pctl->lock, flags);
+	}
+
+	return 0;
+}
+
+static int eqbr_pinconf_group_get(struct pinctrl_dev *pctldev,
+				  unsigned int group, unsigned long *config)
+{
+	unsigned int i, npins, old = 0;
+	const unsigned int *pins;
+	int ret;
+
+	ret = pinctrl_generic_get_group_pins(pctldev, group, &pins, &npins);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < npins; i++) {
+		if (eqbr_pinconf_get(pctldev, pins[i], config))
+			return -ENOTSUPP;
+
+		if (i && old != *config)
+			return -ENOTSUPP;
+
+		old = *config;
+	}
+	return 0;
+}
+
+static int eqbr_pinconf_group_set(struct pinctrl_dev *pctldev,
+				  unsigned int group, unsigned long *configs,
+				  unsigned int num_configs)
+{
+	const unsigned int *pins;
+	unsigned int i, npins;
+	int ret;
+
+	ret = pinctrl_generic_get_group_pins(pctldev, group, &pins, &npins);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < npins; i++) {
+		ret = eqbr_pinconf_set(pctldev, pins[i], configs, num_configs);
+		if (ret)
+			return ret;
+	}
+	return 0;
+}
+
+static const struct pinconf_ops eqbr_pinconf_ops = {
+	.is_generic			= true,
+	.pin_config_get			= eqbr_pinconf_get,
+	.pin_config_set			= eqbr_pinconf_set,
+	.pin_config_group_get		= eqbr_pinconf_group_get,
+	.pin_config_group_set		= eqbr_pinconf_group_set,
+	.pin_config_config_dbg_show	= pinconf_generic_dump_config,
+};
+
+static bool is_func_exist(struct eqbr_pmx_func *funcs, const char *name,
+			 unsigned int nr_funcs, unsigned int *idx)
+{
+	int i;
+
+	if (!funcs || !nr_funcs)
+		return false;
+
+	for (i = 0; i < nr_funcs; i++) {
+		if (funcs[i].name && (strcmp(funcs[i].name, name) == 0) ) {
+			*idx = i;
+			return true;
+		}
+	}
+
+	return false;
+}
+
+static int funcs_utils(struct device *dev, struct eqbr_pmx_func *funcs,
+		       unsigned int *nr_funcs, funcs_util_ops op)
+{
+	struct device_node *node = dev->of_node;
+	struct device_node *np;
+	struct property *prop;
+	const char *fn_name;
+	unsigned int fid;
+	int i, j;
+
+	i = 0;
+	for_each_child_of_node(node, np) {
+		prop = of_find_property(np, "groups", NULL);
+		if (!prop)
+			continue;
+
+		if (of_property_read_string(np, "function", &fn_name)) {
+			/* some groups may not have function, it's OK */
+			dev_dbg(dev, "Group %s: not function binded!\n",
+				(char *)prop->value);
+			continue;
+		}
+
+		switch (op) {
+			case OP_COUNT_NR_FUNCS:
+				if (!is_func_exist(funcs, fn_name,
+						   *nr_funcs, &fid))
+					*nr_funcs = *nr_funcs + 1;
+				break;
+
+			case OP_ADD_FUNCS:
+				if (!is_func_exist(funcs, fn_name,
+						   *nr_funcs, &fid))
+					funcs[i].name = fn_name;
+				break;
+
+			case OP_COUNT_NR_FUNC_GRPS:
+				if (is_func_exist(funcs, fn_name,
+						  *nr_funcs, &fid))
+					funcs[fid].nr_groups++;
+				break;
+
+			case OP_ADD_FUNC_GRPS:
+				if (is_func_exist(funcs, fn_name,
+						  *nr_funcs, &fid)) {
+					for(j=0;
+					    j < funcs[fid].nr_groups;
+					    j++) {
+						if (!funcs[fid].groups[j])
+							break;
+					}
+					funcs[fid].groups[j] = prop->value;
+				}
+				break;
+
+			default:
+				return -EINVAL;
+
+		}
+		i++;
+	}
+
+	return 0;
+}
+
+static int eqbr_build_functions(struct eqbr_pinctrl_drv_data *drvdata)
+{
+	struct device *dev = drvdata->dev;
+	struct eqbr_pmx_func *funcs = NULL;
+	unsigned int nr_funcs = 0;
+	int i, ret;
+
+	ret = funcs_utils(dev, funcs, &nr_funcs, OP_COUNT_NR_FUNCS);
+	if (ret)
+		return ret;
+
+	funcs = devm_kcalloc(dev, nr_funcs, sizeof(*funcs), GFP_KERNEL);
+	if (!funcs)
+		return -ENOMEM;
+
+	ret = funcs_utils(dev, funcs, &nr_funcs, OP_ADD_FUNCS);
+	if (ret)
+		return ret;
+
+	ret = funcs_utils(dev, funcs, &nr_funcs, OP_COUNT_NR_FUNC_GRPS);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < nr_funcs; i++) {
+		if (funcs[i].nr_groups) {
+			funcs[i].groups = devm_kcalloc(dev, funcs[i].nr_groups,
+						       sizeof(*(funcs[i].groups)),
+						       GFP_KERNEL);
+			if (!funcs[i].groups)
+				return -ENOMEM;
+		}
+	}
+
+	ret = funcs_utils(dev, funcs, &nr_funcs, OP_ADD_FUNC_GRPS);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < nr_funcs; i++) {
+		ret = pinmux_generic_add_function(drvdata->pctl_dev,
+						  funcs[i].name,
+						  funcs[i].groups,
+						  funcs[i].nr_groups,
+						  drvdata);
+		if (ret < 0) {
+			dev_err(dev, "Failed to register function %s\n",
+				funcs[i].name);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int eqbr_build_groups(struct eqbr_pinctrl_drv_data *drvdata)
+{
+	struct device *dev = drvdata->dev;
+	struct device_node *node = dev->of_node;
+	unsigned int *pinmux, pin_id, pinmux_id;
+	struct group_desc group;
+	struct device_node *np;
+	struct property *prop;
+	int j, err;
+
+	for_each_child_of_node(node, np) {
+		prop = of_find_property(np, "groups", NULL);
+		if (!prop)
+			continue;
+
+		group.num_pins = of_property_count_u32_elems(np, "pins");
+		if (group.num_pins < 0) {
+			dev_err(dev, "No pins in the group: %s\n", prop->name);
+			return -EINVAL;
+		}
+		group.name = prop->value;
+		group.pins = devm_kcalloc(dev, group.num_pins,
+					  sizeof(*(group.pins)), GFP_KERNEL);
+		if (!group.pins)
+			return -ENOMEM;
+
+		pinmux = devm_kcalloc(dev, group.num_pins, sizeof(*pinmux),
+				      GFP_KERNEL);
+		if (!pinmux)
+			return -ENOMEM;
+
+		for (j = 0; j < group.num_pins; j++) {
+			if (of_property_read_u32_index(np, "pins", j, &pin_id)) {
+				dev_err(dev, "Group %s: Read intel pins id failed\n",
+					group.name);
+				return -EINVAL;
+			}
+			if (pin_id >= drvdata->pctl_desc.npins) {
+				dev_err(dev, "Group %s: Invalid pin ID, idx: %d, pin %u\n",
+					group.name, j, pin_id);
+				return -EINVAL;
+			}
+			group.pins[j] = pin_id;
+			if (of_property_read_u32_index(np, "pinmux", j, &pinmux_id)) {
+				dev_err(dev, "Group %s: Read intel pinmux id failed\n",
+					group.name);
+				return -EINVAL;
+			}
+			pinmux[j] = pinmux_id;
+		}
+
+		err = pinctrl_generic_add_group(drvdata->pctl_dev, group.name,
+						group.pins, group.num_pins,
+						pinmux);
+		if (err < 0) {
+			dev_err(dev, "Failed to register group %s\n", group.name);
+			return err;
+		}
+		memset(&group, 0, sizeof(group));
+		pinmux = NULL;
+	}
+
+	return 0;
+}
+
+static int pinctrl_reg(struct eqbr_pinctrl_drv_data *drvdata)
+{
+	struct pinctrl_desc *pctl_desc;
+	struct pinctrl_pin_desc *pdesc;
+	struct device *dev;
+	unsigned int nr_pins;
+	char *pin_names;
+	int i, ret;
+
+	dev = drvdata->dev;
+	pctl_desc = &drvdata->pctl_desc;
+	pctl_desc->name = "eqbr-pinctrl";
+	pctl_desc->owner = THIS_MODULE;
+	pctl_desc->pctlops = &eqbr_pctl_ops;
+	pctl_desc->pmxops = &eqbr_pinmux_ops;
+	pctl_desc->confops = &eqbr_pinconf_ops;
+	raw_spin_lock_init(&drvdata->lock);
+
+	for (i = 0, nr_pins = 0; i < drvdata->nr_banks; i++)
+		nr_pins += drvdata->pin_banks[i].nr_pins;
+
+	pdesc = devm_kcalloc(dev, nr_pins, sizeof(*pdesc), GFP_KERNEL);
+	if (!pdesc)
+		return -ENOMEM;
+	pin_names = devm_kcalloc(dev, nr_pins, PIN_NAME_LEN, GFP_KERNEL);
+	if (!pin_names)
+		return -ENOMEM;
+
+	for (i = 0; i < nr_pins; i++) {
+		sprintf(pin_names, PIN_NAME_FMT, i);
+		pdesc[i].number = i;
+		pdesc[i].name = pin_names;
+		pin_names += PIN_NAME_LEN;
+	}
+	pctl_desc->pins = pdesc;
+	pctl_desc->npins = nr_pins;
+	dev_dbg(dev, "pinctrl total pin number: %u\n", nr_pins);
+
+	ret = devm_pinctrl_register_and_init(dev, pctl_desc, drvdata,
+					     &drvdata->pctl_dev);
+	if (ret)
+		return ret;
+
+	ret = eqbr_build_groups(drvdata);
+	if (ret) {
+		dev_err(dev, "Failed to build groups\n");
+		return ret;
+	}
+
+	ret = eqbr_build_functions(drvdata);
+	if (ret) {
+		dev_err(dev, "Failed to build groups\n");
+		return ret;
+	}
+
+	return pinctrl_enable(drvdata->pctl_dev);
+}
+
+static int pinbank_init(struct device_node *np,
+			struct eqbr_pinctrl_drv_data *drvdata,
+			struct eqbr_pin_bank *bank, unsigned int id)
+{
+	struct device *dev = drvdata->dev;
+	struct of_phandle_args spec;
+	int ret;
+
+	bank->membase = drvdata->membase + id * PAD_REG_OFF;
+
+	ret = of_parse_phandle_with_fixed_args(np, "gpio-ranges", 3, 0, &spec);
+	if (ret) {
+		dev_err(dev, "gpio-range not available!\n");
+		return ret;
+	}
+
+	bank->pin_base = spec.args[1];
+	bank->nr_pins = spec.args[2];
+
+	bank->aval_pinmap = readl(bank->membase + REG_AVAIL);
+	bank->id = id;
+
+	dev_dbg(dev, "pinbank id: %d, reg: %px, pinbase: %u, pin number: %u, pinmap: 0x%x\n",
+		id, bank->membase, bank->pin_base,
+		bank->nr_pins, bank->aval_pinmap);
+
+	return ret;
+}
+
+static int pinbank_probe(struct eqbr_pinctrl_drv_data *drvdata)
+{
+	struct device *dev = drvdata->dev;
+	struct device_node *np_gpio;
+	struct eqbr_gpio_ctrl *gctrls;
+	struct eqbr_pin_bank *banks;
+	int i, nr_gpio;
+
+	/* Count gpio bank number */
+	nr_gpio = 0;
+	for_each_node_by_name(np_gpio, "gpio") {
+		if (of_device_is_available(np_gpio))
+			nr_gpio++;
+	}
+
+	if (!nr_gpio) {
+		dev_err(dev, "NO pin bank available!\n");
+		return -ENODEV;
+	}
+
+	/* Count pin bank number and gpio controller number */
+	banks = devm_kcalloc(dev, nr_gpio, sizeof(*banks), GFP_KERNEL);
+	if (!banks)
+		return -ENOMEM;
+
+	gctrls = devm_kcalloc(dev, nr_gpio, sizeof(*gctrls), GFP_KERNEL);
+	if (!gctrls)
+		return -ENOMEM;
+
+	dev_dbg(dev, "found %d gpio controller!\n", nr_gpio);
+
+	/* Initialize Pin bank */
+	i = 0;
+	for_each_node_by_name(np_gpio, "gpio") {
+		if (!of_device_is_available(np_gpio))
+			continue;
+
+		pinbank_init(np_gpio, drvdata, banks + i, i);
+
+		gctrls[i].node = np_gpio;
+		gctrls[i].bank = banks + i;
+		i++;
+	}
+
+	drvdata->pin_banks = banks;
+	drvdata->nr_banks = nr_gpio;
+	drvdata->gpio_ctrls = gctrls;
+	drvdata->nr_gpio_ctrls = nr_gpio;
+
+	return 0;
+}
+
+static int eqbr_pinctrl_probe(struct platform_device *pdev)
+{
+	struct eqbr_pinctrl_drv_data *drvdata;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL);
+	if (!drvdata)
+		return -ENOMEM;
+
+	drvdata->dev = dev;
+
+	drvdata->membase = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(drvdata->membase))
+		return PTR_ERR(drvdata->membase);
+
+	ret = pinbank_probe(drvdata);
+	if (ret)
+		return ret;
+
+	ret = pinctrl_reg(drvdata);
+	if (ret)
+		return ret;
+
+	ret = gpiolib_reg(drvdata);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, drvdata);
+	return 0;
+}
+
+static const struct of_device_id eqbr_pinctrl_dt_match[] = {
+	{ .compatible = "intel,lgm-pinctrl" },
+	{}
+};
+
+static struct platform_driver eqbr_pinctrl_driver = {
+	.probe	= eqbr_pinctrl_probe,
+	.driver = {
+		.name = "eqbr-pinctrl",
+		.of_match_table = eqbr_pinctrl_dt_match,
+	},
+};
+
+module_platform_driver(eqbr_pinctrl_driver);
+
+MODULE_AUTHOR("Zhu Yixin <yixin.zhu@intel.com>, Rahul Tanwar <rahul.tanwar@intel.com>");
+MODULE_DESCRIPTION("Pinctrl Driver for LGM SoC (Equilibrium)");
diff --git a/drivers/pinctrl/pinctrl-equilibrium.h b/drivers/pinctrl/pinctrl-equilibrium.h
new file mode 100644
index 000000000000..34bafcb6a2fe
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-equilibrium.h
@@ -0,0 +1,144 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ *  Copyright(c) 2019 Intel Corporation.
+ */
+
+#ifndef __PINCTRL_EQUILIBRIUM_H
+#define __PINCTRL_EQUILIBRIUM_H
+
+/* PINPAD register offset */
+#define REG_PMX_BASE	0x0	/* Port Multiplexer Control Register */
+#define REG_PUEN	0x80	/* PULL UP Enable Register */
+#define REG_PDEN	0x84	/* PULL DOWN Enable Register */
+#define REG_SRC		0x88	/* Slew Rate Control Register */
+#define REG_DCC0	0x8C	/* Drive Current Control Register 0 */
+#define REG_DCC1	0x90	/* Drive Current Control Register 1 */
+#define REG_OD		0x94	/* Open Drain Enable Register */
+#define REG_AVAIL	0x98	/* Pad Control Availability Register */
+#define DRV_CUR_PINS	16	/* Drive Current pin number per register */
+#define REG_DRCC(x)	(REG_DCC0 + (x) * 4) /* Driver current macro */
+
+/* GPIO register offset */
+#define GPIO_OUT	0x0	/* Data Output Register */
+#define GPIO_IN		0x4	/* Data Input Register */
+#define GPIO_DIR	0x8	/* Direction Register */
+#define GPIO_EXINTCR0	0x18	/* External Interrupt Control Register 0 */
+#define GPIO_EXINTCR1	0x1C	/* External Interrupt Control Register 1 */
+#define GPIO_IRNCR	0x20	/* IRN Capture Register */
+#define GPIO_IRNICR	0x24	/* IRN Interrupt Control Register */
+#define GPIO_IRNEN	0x28	/* IRN Interrupt Enable Register */
+#define GPIO_IRNCFG	0x2C	/* IRN Interrupt Configuration Register */
+#define GPIO_IRNRNSET	0x30	/* IRN Interrupt Enable Set Register */
+#define GPIO_IRNENCLR	0x34	/* IRN Interrupt Enable Clear Register */
+#define GPIO_OUTSET	0x40	/* Output Set Register */
+#define GPIO_OUTCLR	0x44	/* Output Clear Register */
+#define GPIO_DIRSET	0x48	/* Direction Set Register */
+#define GPIO_DIRCLR	0x4C	/* Direction Clear Register */
+
+/* parse given pin's driver current value */
+#define PARSE_DRV_CURRENT(val, pin) (((val) >> ((pin) << 1)) & 0x3)
+
+#define GPIO_EDGE_TRIG		0
+#define GPIO_LEVEL_TRIG		1
+#define GPIO_SINGLE_EDGE	0
+#define GPIO_BOTH_EDGE		1
+#define GPIO_POSITIVE_TRIG	0
+#define GPIO_NEGATIVE_TRIG	1
+
+#define EQBR_GPIO_MODE		0
+
+typedef enum {
+	OP_COUNT_NR_FUNCS,
+	OP_ADD_FUNCS,
+	OP_COUNT_NR_FUNC_GRPS,
+	OP_ADD_FUNC_GRPS,
+	OP_NONE,
+} funcs_util_ops;
+
+/**
+ * struct gpio_irq_type: gpio irq configuration
+ * @trig_type: level trigger or edge trigger
+ * @edge_type: sigle edge or both edge
+ * @logic_type: positive trigger or negative trigger
+ */
+struct gpio_irq_type {
+	unsigned int trig_type;
+	unsigned int edge_type;
+	unsigned int logic_type;
+};
+
+/**
+ * struct eqbr_pmx_func: represent a pin function.
+ * @name: name of the pin function, used to lookup the function.
+ * @groups: one or more names of pin groups that provide this function.
+ * @nr_groups: number of groups included in @groups.
+ */
+struct eqbr_pmx_func {
+	const char		*name;
+	const char		**groups;
+	unsigned int		nr_groups;
+};
+
+/**
+ * struct eqbr_pin_bank: represent a pin bank.
+ * @membase: base address of the pin bank register.
+ * @id: bank id, to idenify the unique bank.
+ * @pin_base: starting pin number of the pin bank.
+ * @nr_pins: number of the pins of the pin bank.
+ * @aval_pinmap: available pin bitmap of the pin bank.
+ */
+struct eqbr_pin_bank {
+	void __iomem		*membase;
+	unsigned int		id;
+	unsigned int		pin_base;
+	unsigned int		nr_pins;
+	u32			aval_pinmap;
+};
+
+/**
+ * struct eqbr_gpio_ctrl: represent a gpio controller.
+ * @node: device node of gpio controller.
+ * @bank: pointer to corresponding pin bank.
+ * @membase: base address of the gpio controller.
+ * @chip: gpio chip.
+ * @ic:   irq chip.
+ * @name: gpio chip name.
+ * @virq: irq number of the gpio chip to parent's irq domain.
+ * @lock: spin lock to protect gpio register write.
+ */
+struct eqbr_gpio_ctrl {
+	struct device_node	*node;
+	struct eqbr_pin_bank	*bank;
+	void __iomem		*membase;
+	struct gpio_chip	chip;
+	struct irq_chip		ic;
+	const char		*name;
+	unsigned int		virq;
+	raw_spinlock_t		lock; /* protect gpio register */
+};
+
+/**
+ * struct eqbr_pinctrl_drv_data:
+ * @dev: device instance representing the controller.
+ * @pctl_desc: pin controller descriptor.
+ * @pctl_dev: pin control class device
+ * @membase: base address of pin controller
+ * @pin_banks: list of pin banks of the driver.
+ * @nr_banks: number of pin banks.
+ * @gpio_ctrls: list of gpio controllers.
+ * @nr_gpio_ctrls: number of gpio controllers.
+ * @lock: protect pinctrl register write
+ */
+struct eqbr_pinctrl_drv_data {
+	struct device			*dev;
+	struct pinctrl_desc		pctl_desc;
+	struct pinctrl_dev		*pctl_dev;
+	void __iomem			*membase;
+	struct eqbr_pin_bank		*pin_banks;
+	unsigned int			nr_banks;
+	struct eqbr_gpio_ctrl		*gpio_ctrls;
+	unsigned int			nr_gpio_ctrls;
+	raw_spinlock_t			lock; /* protect pinpad register */
+};
+
+#endif /* __PINCTRL_EQUILIBRIUM_H */