diff --git a/board/efikamx/Makefile b/board/efikamx/Makefile
index ee4a16e..860e4d2 100644
--- a/board/efikamx/Makefile
+++ b/board/efikamx/Makefile
@@ -28,6 +28,9 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).o
 
 COBJS	:= efikamx.o
+ifdef	CONFIG_CMD_USB
+COBJS	+= efikamx-usb.o
+endif
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/board/efikamx/efika.h b/board/efikamx/efika.h
new file mode 100644
index 0000000..b3532e2
--- /dev/null
+++ b/board/efikamx/efika.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2011 Jana Rapava <fermata7@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * EHCI USB
+ */
+#ifdef	CONFIG_CMD_USB
+void setup_iomux_usb(void);
+#else
+static inline void setup_iomux_usb(void) { }
+#endif
diff --git a/board/efikamx/efikamx-usb.c b/board/efikamx/efikamx-usb.c
new file mode 100644
index 0000000..ac031ef
--- /dev/null
+++ b/board/efikamx/efikamx-usb.c
@@ -0,0 +1,420 @@
+/*
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * Copyright (C) 2011 Jana Rapava <fermata7@gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <usb.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx5x_pins.h>
+#include <asm/arch/iomux.h>
+#include <asm/gpio.h>
+#include <usb/ehci-fsl.h>
+#include <errno.h>
+#include <watchdog.h>
+
+#include <usb/ehci.h>
+#include <usb/ehci-core.h>
+
+/*
+ * Configure the USB H1 and USB H2 IOMUX.
+ */
+#define USB_PAD_CONFIG	(PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST | \
+			PAD_CTL_DRV_HIGH | PAD_CTL_100K_PU | \
+			PAD_CTL_HYS_ENABLE | PAD_CTL_PUE_PULL)
+void setup_iomux_usb(void)
+{
+	/*
+	 * Configure USBH1 pads
+	 */
+	mxc_request_iomux(MX51_PIN_USBH1_STP, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_STP, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_CLK, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_CLK, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_DIR, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_DIR, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_NXT, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_NXT, USB_PAD_CONFIG);
+
+	mxc_request_iomux(MX51_PIN_USBH1_DATA0, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_DATA0, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_DATA1, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_DATA1, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_DATA2, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_DATA2, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_DATA3, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_DATA3, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_DATA4, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_DATA4, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_DATA5, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_DATA5, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_DATA6, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_DATA6, USB_PAD_CONFIG);
+	mxc_request_iomux(MX51_PIN_USBH1_DATA7, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_DATA7, USB_PAD_CONFIG);
+
+	/*
+	 * Configure USBH1 control pads
+	 */
+
+	/* USB PHY reset */
+	mxc_request_iomux(MX51_PIN_EIM_D27, IOMUX_CONFIG_ALT1);
+	mxc_iomux_set_pad(MX51_PIN_EIM_D27, PAD_CTL_PKE_ENABLE |
+			PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH);
+
+	/* USB HUB reset */
+	mxc_request_iomux(MX51_PIN_GPIO1_5, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_GPIO1_5, PAD_CTL_PKE_ENABLE |
+			PAD_CTL_SRE_FAST | PAD_CTL_DRV_HIGH);
+
+
+	if (machine_is_efikasb()) {
+		/*
+		 * Configure USBH2 pads (used on EfikaSB)
+		 */
+		/* USBH2_DATA */
+		mxc_request_iomux(MX51_PIN_EIM_D16, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_D16, USB_PAD_CONFIG);
+		mxc_request_iomux(MX51_PIN_EIM_D17, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_D17, USB_PAD_CONFIG);
+		mxc_request_iomux(MX51_PIN_EIM_D18, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_D18, USB_PAD_CONFIG);
+		mxc_request_iomux(MX51_PIN_EIM_D19, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_D19, USB_PAD_CONFIG);
+		mxc_request_iomux(MX51_PIN_EIM_D20, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_D20, USB_PAD_CONFIG);
+		mxc_request_iomux(MX51_PIN_EIM_D21, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_D21, USB_PAD_CONFIG);
+		mxc_request_iomux(MX51_PIN_EIM_D22, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_D22, USB_PAD_CONFIG);
+		mxc_request_iomux(MX51_PIN_EIM_D23, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_D23, USB_PAD_CONFIG);
+
+		/* USBH2_CLK */
+		mxc_request_iomux(MX51_PIN_EIM_A24, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_A24, USB_PAD_CONFIG);
+		/* USBH2_DIR */
+		mxc_request_iomux(MX51_PIN_EIM_A25, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_A25, USB_PAD_CONFIG);
+		/* USBH2_STP */
+		mxc_request_iomux(MX51_PIN_EIM_A26, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_A26, USB_PAD_CONFIG);
+		/* USBH2_NXT */
+		mxc_request_iomux(MX51_PIN_EIM_A27, IOMUX_CONFIG_ALT2);
+		mxc_iomux_set_pad(MX51_PIN_EIM_A27, USB_PAD_CONFIG);
+	}
+
+	/* WIFI EN (act low) */
+	mxc_request_iomux(MX51_PIN_EIM_A22, IOMUX_CONFIG_GPIO);
+	mxc_iomux_set_pad(MX51_PIN_EIM_A22, 0);
+	/* WIFI RESET */
+	mxc_request_iomux(MX51_PIN_EIM_A16, IOMUX_CONFIG_GPIO);
+	mxc_iomux_set_pad(MX51_PIN_EIM_A16, 0);
+	/* BT EN (act low) */
+	mxc_request_iomux(MX51_PIN_EIM_A17, IOMUX_CONFIG_GPIO);
+	mxc_iomux_set_pad(MX51_PIN_EIM_A17, 0);
+}
+
+/*
+ * Enable devices connected to USB buses.
+ */
+void efika_usb_enable_devices(void)
+{
+	/* Enable Bluetooth */
+	gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A17), 0);
+	udelay(10000);
+	gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_A17), 1);
+
+	/* Enable WiFi */
+	gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A22), 1);
+	udelay(10000);
+
+	/* Reset the WiFi chip */
+	gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A16), 0);
+	udelay(10000);
+	gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_A16), 1);
+}
+
+/*
+ * Reset USB HUB (or HUBs on EfikaSB).
+ */
+void efika_usb_hub_reset(void)
+{
+	/* HUB reset */
+	gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_GPIO1_5), 1);
+	udelay(1000);
+	gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_GPIO1_5), 0);
+	udelay(1000);
+	gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_GPIO1_5), 1);
+}
+
+/*
+ * Reset USB PHY (or PHYs on EfikaSB).
+ */
+void efika_usb_phy_reset(void)
+{
+	/* SMSC 3317 PHY reset */
+	gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_D27), 0);
+	udelay(1000);
+	gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_D27), 1);
+}
+
+/*
+ * Configure control registers of the USB controller.
+ */
+void control_regs_setup(struct mx5_usb_control_regs *control)
+{
+	clrsetbits_le32(&control->usbctrl,
+		(MXC_OTG_WUE | MXC_OTG_PM | MX51_H1_ULPI_IE | MX51_H1_WUE),
+		MX51_H1_PM);
+
+	clrsetbits_le32(&control->phyctrl0,
+			MX51_OTG_OVERCURD,
+			MX51_EHCI_POWERPINSE);
+
+	clrsetbits_le32(&control->phyctrl1,
+			MX51_SYSCLOCK_MASK,
+			MX51_SYSCLOCK_24_MHZ);
+
+	setbits_le32(&control->usbctrl1, MX51_H1_EXTCLKE);
+
+	clrsetbits_le32(&control->uh2ctrl,
+			(MX51_H2_ULPI_IE | MX51_H2_WUE),
+			MX51_H2_PM);
+
+	udelay(10000);
+}
+
+#define ULPI_ADDR_SHIFT		16
+#define ulpi_write_mask(value)	((value) & 0xff)
+#define ulpi_read_mask(value)	(((value) >> 8) & 0xff)
+
+int ulpi_wait(struct usb_ehci *ehci, u32 ulpi_value, u32 ulpi_mask)
+{
+	int timeout = ULPI_TIMEOUT;
+	u32 tmp;
+
+	writel(ulpi_value, &ehci->ulpi_viewpoint);
+
+	/* Wait for the bits in ulpi_mask to become zero. */
+	while (--timeout) {
+		tmp = readl(&ehci->ulpi_viewpoint);
+		if (!(tmp & ulpi_mask))
+			break;
+		WATCHDOG_RESET();
+	}
+
+	return !timeout;
+}
+
+int ulpi_wakeup(struct usb_ehci *ehci)
+{
+	if (readl(&ehci->ulpi_viewpoint) & ULPI_SS)
+		return 0; /* already awake */
+	return ulpi_wait(ehci, ULPI_WU, ULPI_WU);
+}
+
+void ulpi_write(struct usb_ehci *ehci, u32 reg, u32 value)
+{
+	if (ulpi_wakeup(ehci)) {
+		printf("ULPI wakeup timed out\n");
+		return;
+	}
+
+	if (ulpi_wait(ehci, ULPI_RWRUN | ULPI_RWCTRL |
+	reg << ULPI_ADDR_SHIFT | ulpi_write_mask(value), ULPI_RWRUN))
+		printf("ULPI write timed out\n");
+}
+
+u32 ulpi_read(struct usb_ehci *ehci, u32 reg)
+{
+	if (ulpi_wakeup(ehci)) {
+		printf("ULPI wakeup timed out\n");
+		return 0;
+	}
+
+	if (ulpi_wait(ehci, ULPI_RWRUN | reg << ULPI_ADDR_SHIFT, ULPI_RWRUN)) {
+		printf("ULPI read timed out\n");
+		return 0;
+	}
+	return ulpi_read_mask(readl(&ehci->ulpi_viewpoint));
+}
+
+void ulpi_init(struct usb_ehci *ehci, struct mxc_ulpi_regs *ulpi)
+{
+	u32 tmp = 0;
+	int reg, i;
+
+	/* Assemble ID from four ULPI ID registers (8 bits each). */
+	for (reg = ULPI_ID_REGS_COUNT - 1; reg >= 0; reg--)
+		tmp |= ulpi_read(ehci, reg) << (reg * 8);
+
+	/* Split ID into vendor and product ID. */
+	debug("Found ULPI TX, ID %04x:%04x\n", tmp >> 16, tmp & 0xffff);
+
+	/* ULPI integrity check */
+	for (i = 0; i < 2; i++) {
+		ulpi_write(ehci, (u32)&ulpi->scratch_write,
+			ULPI_TEST_VALUE << i);
+		tmp = ulpi_read(ehci, (u32)&ulpi->scratch_write);
+
+		if (tmp != (ULPI_TEST_VALUE << i)) {
+			printf("ULPI integrity check failed\n");
+			return;
+		}
+	}
+
+	/* Set ULPI flags. */
+	ulpi_write(ehci, (u32)&ulpi->otg_ctrl_write,
+		ULPI_OTG_EXT_VBUS_IND |
+		ULPI_OTG_DM_PULLDOWN | ULPI_OTG_DP_PULLDOWN);
+	ulpi_write(ehci, (u32)&ulpi->function_ctrl_write,
+		ULPI_FC_XCVR_SELECT | ULPI_FC_OPMODE_NORMAL |
+		ULPI_FC_SUSPENDM_PWRED);
+	ulpi_write(ehci, (u32)&ulpi->iface_ctrl_write, 0);
+	ulpi_write(ehci, (u32)&ulpi->otg_ctrl_set,
+		ULPI_OTG_DRV_VBUS | ULPI_OTG_DRV_VBUS_EXT);
+
+	/*
+	 * NOTE: This violates USB specification, but otherwise, USB on Efika
+	 * doesn't charge VBUS and as a result, USB doesn't work.
+	 */
+	ulpi_write(ehci, (u32)&ulpi->otg_ctrl_set, ULPI_OTG_CHRG_VBUS);
+}
+
+/*
+ * Solve the VBUS reset problem on Efika
+ * by setting the CHRG_VBUS bit in the reset.
+ */
+void ehci_fixup(uint32_t *status_reg, uint32_t *reg_ref)
+{
+	struct usb_ehci *ehci = (struct usb_ehci *)(OTG_BASE_ADDR +
+		MX51_REGISTER_LAYOUT_LENGTH);
+	struct mxc_ulpi_regs *ulpi = (struct mxc_ulpi_regs *)0;
+
+	u32 tmp = ulpi_read(ehci, (u32)&ulpi->otg_ctrl_write);
+	tmp |= ULPI_OTG_CHRG_VBUS;
+	ulpi_write(ehci, (u32)&ulpi->otg_ctrl_write, tmp);
+
+	/* USB 2.0 specification say 50 ms resets on root. */
+	wait_ms(50);
+
+	/* Now terminate the reset. */
+	*reg_ref = ehci_readl(status_reg);
+	*reg_ref |= EHCI_PS_PE;
+}
+
+void ehci0_init(struct usb_ehci *ehci)
+{
+	writel(MX51_16BIT_UTMI, &ehci->portsc);
+}
+
+void ehci1_init(struct usb_ehci *ehci, struct mxc_ulpi_regs *ulpi)
+{
+	mxc_request_iomux(MX51_PIN_USBH1_STP, IOMUX_CONFIG_ALT2);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_STP, PAD_CTL_DRV_HIGH |
+				PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST);
+	gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_USBH1_STP), 0);
+	udelay(1000);
+	gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_USBH1_STP), 1);
+	udelay(1000);
+
+	mxc_request_iomux(MX51_PIN_USBH1_STP, IOMUX_CONFIG_ALT0);
+	mxc_iomux_set_pad(MX51_PIN_USBH1_STP, USB_PAD_CONFIG);
+	udelay(10000);
+
+	clrbits_le32(&ehci->usbcmd, MX51_ITC_IMMEDIATE_MASK);
+	udelay(10000);
+
+	writel(MX51_ULPI_MODE_MASK, &ehci->portsc);
+	udelay(10000);
+
+	ulpi_init(ehci, ulpi);
+}
+
+void ehci2_init(struct usb_ehci *ehci, struct mxc_ulpi_regs *ulpi)
+{
+	mxc_request_iomux(MX51_PIN_EIM_A26, IOMUX_CONFIG_ALT1);
+	mxc_iomux_set_pad(MX51_PIN_EIM_A26, PAD_CTL_DRV_HIGH |
+				PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST);
+	gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_A26), 0);
+	udelay(1000);
+	gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_A26), 1);
+	udelay(1000);
+
+	mxc_request_iomux(MX51_PIN_EIM_A26, IOMUX_CONFIG_ALT2);
+	mxc_iomux_set_pad(MX51_PIN_EIM_A26, USB_PAD_CONFIG);
+
+	writel(MX51_ULPI_MODE_MASK, &ehci->portsc);
+	udelay(10000);
+
+	ulpi_init(ehci, ulpi);
+}
+
+int ehci_hcd_init(void)
+{
+	struct usb_ehci *ehci;
+	struct mx5_usb_control_regs *mx5_usb_control_regs;
+	struct mxc_ulpi_regs *ulpi;
+
+	mx5_usb_control_regs = (struct mx5_usb_control_regs *)(OTG_BASE_ADDR +
+		 MX5_CTRL_REGS_OFFSET);
+	control_regs_setup(mx5_usb_control_regs);
+	ulpi = (struct mxc_ulpi_regs *)0;
+
+	/* Init EHCI core */
+	ehci = (struct usb_ehci *)(OTG_BASE_ADDR +
+		(MX51_REGISTER_LAYOUT_LENGTH * CONFIG_MXC_USB_PORT));
+	hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
+	hcor = (struct ehci_hcor *)((uint32_t) hccr +
+			HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
+	setbits_le32(&ehci->usbmode, CM_HOST);
+	setbits_le32(&ehci->control, USB_EN);
+
+	/* Init iMX51 EHCI */
+	efika_usb_phy_reset();
+	efika_usb_hub_reset();
+	efika_usb_enable_devices();
+
+	switch (CONFIG_MXC_USB_PORT) {
+	case 0:
+		ehci0_init(ehci);
+		break;
+	case 1:
+		ehci1_init(ehci, ulpi);
+		break;
+	case 2:
+		if (machine_is_efikasb())
+			ehci2_init(ehci, ulpi);
+		break;
+	};
+
+	/* EfikaMX USB has issues ... */
+	udelay(10000);
+
+	return 0;
+}
+
+int ehci_hcd_stop(void)
+{
+	return 0;
+}
diff --git a/board/efikamx/efikamx.c b/board/efikamx/efikamx.c
index 0c4e24b..8e9b42b 100644
--- a/board/efikamx/efikamx.c
+++ b/board/efikamx/efikamx.c
@@ -37,6 +37,8 @@
 #include <fsl_pmic.h>
 #include <mc13892.h>
 
+#include "efika.h"
+
 DECLARE_GLOBAL_DATA_PTR;
 
 /*
@@ -678,6 +680,7 @@ int board_late_init(void)
 
 	setup_iomux_led();
 	setup_iomux_ata();
+	setup_iomux_usb();
 
 	efikamx_toggle_led(EFIKAMX_LED_BLUE);
 
diff --git a/include/configs/efikamx.h b/include/configs/efikamx.h
index 54f48e4..010a16a 100644
--- a/include/configs/efikamx.h
+++ b/include/configs/efikamx.h
@@ -44,6 +44,10 @@
 
 #define CONFIG_SYS_TEXT_BASE		0x97800000
 
+#define	CONFIG_L2_OFF
+#define	CONFIG_SYS_ICACHE_OFF
+#define	CONFIG_SYS_DCACHE_OFF
+
 /*
  * Bootloader Components Configuration
  */
@@ -172,6 +176,18 @@
 #endif
 
 /*
+ * USB
+ */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI			/* Enable EHCI USB support */
+#define CONFIG_MXC_USB_PORT	1
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define	CONFIG_USB_KEYBOARD
+#endif /* CONFIG_CMD_USB */
+
+/*
  * Filesystems
  */
 #ifdef CONFIG_CMD_FAT
