@@ -3,6 +3,9 @@
# Copyright (c) 2016 Google, Inc
obj-$(CONFIG_SPL_BUILD) += systemagent.o
+ifndef CONFIG_TPL_BUILD
+obj-y += punit.o
+endif
obj-y += gpio.o
obj-y += hostbridge.o
new file mode 100644
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Google LLC
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <spl.h>
+#include <asm/cpu.h>
+#include <asm/cpu_common.h>
+#include <asm/intel_regs.h>
+#include <asm/io.h>
+#include <asm/pci.h>
+#include <asm/arch/systemagent.h>
+
+/**
+ * struct apl_punit_platdata - platform data for punit
+ *
+ * @pciex_region_size: BAR length in bytes
+ */
+struct apl_punit_platdata {
+ pci_dev_t bdf;
+};
+
+/*
+ * Punit Initialization code. This all isn't documented, but
+ * this is the recipe.
+ */
+static int punit_init(struct udevice *dev)
+{
+ struct apl_punit_platdata *plat = dev_get_platdata(dev);
+ struct udevice *cpu;
+ u32 reg;
+ ulong start;
+ int ret;
+
+ /* Thermal throttle activation offset */
+ ret = uclass_first_device_err(UCLASS_CPU, &cpu);
+ if (ret)
+ return log_msg_ret("Cannot find CPU", ret);
+ cpu_configure_thermal_target(cpu);
+
+ /*
+ * Software Core Disable Mask (P_CR_CORE_DISABLE_MASK_0_0_0_MCHBAR).
+ * Enable all cores here.
+ */
+ writel(0, MCHBAR_REG(CORE_DISABLE_MASK));
+
+ /* P-Unit bring up */
+ reg = readl(MCHBAR_REG(BIOS_RESET_CPL));
+ if (reg == 0xffffffff) {
+ /* P-unit not found */
+ debug("Punit MMIO not available\n");
+ return -ENOENT;
+ }
+
+ /* Set Punit interrupt pin IPIN offset 3D */
+ pci_x86_write_config(plat->bdf, PCI_INTERRUPT_PIN, 0x2, PCI_SIZE_8);
+
+ /* Set PUINT IRQ to 24 and INTPIN LOCK */
+ writel(PUINT_THERMAL_DEVICE_IRQ_VEC_NUMBER |
+ PUINT_THERMAL_DEVICE_IRQ_LOCK,
+ MCHBAR_REG(PUNIT_THERMAL_DEVICE_IRQ));
+
+ if (!IS_ENABLED(SOC_INTEL_GLK))
+ clrsetbits_le32(MCHBAR_REG(0x7818), 0x1fe0, 0x220);
+
+ /* Stage0 BIOS Reset Complete (RST_CPL) */
+ enable_bios_reset_cpl();
+
+ /*
+ * Poll for bit 8 to check if PCODE has completed its action in response
+ * to BIOS Reset complete. We wait here till 1 ms for the bit to get
+ * set.
+ */
+ start = get_timer(0);
+ while (!(readl(MCHBAR_REG(BIOS_RESET_CPL)) & PCODE_INIT_DONE)) {
+ if (get_timer(start) > 1) {
+ debug("PCODE Init Done timeout\n");
+ return -ETIMEDOUT;
+ }
+ udelay(100);
+ }
+ debug("PUNIT init complete\n");
+
+ return 0;
+}
+
+static int apl_punit_probe(struct udevice *dev)
+{
+ if (spl_phase() == PHASE_SPL)
+ return punit_init(dev);
+
+ return 0;
+}
+
+static int apl_punit_ofdata_to_platdata(struct udevice *dev)
+{
+ struct apl_punit_platdata *plat = dev_get_platdata(dev);
+ int root;
+
+ root = pci_x86_get_devfn(dev);
+ if (root < 0)
+ return log_msg_ret("Cannot get host-bridge PCI address", root);
+ plat->bdf = root;
+
+ return 0;
+}
+
+static const struct udevice_id apl_syscon_ids[] = {
+ { .compatible = "intel,apl-punit", .data = X86_SYSCON_PUNIT },
+ { }
+};
+
+U_BOOT_DRIVER(syscon_intel_punit) = {
+ .name = "intel_punit_syscon",
+ .id = UCLASS_SYSCON,
+ .of_match = apl_syscon_ids,
+ .ofdata_to_platdata = apl_punit_ofdata_to_platdata,
+ .probe = apl_punit_probe,
+};
Add a driver for the apollolake power unit. It is modelled as a syscon driver since it only needs to be probed. Signed-off-by: Simon Glass <sjg@chromium.org> --- arch/x86/cpu/apollolake/Makefile | 3 + arch/x86/cpu/apollolake/punit.c | 121 +++++++++++++++++++++++++++++++ 2 files changed, 124 insertions(+) create mode 100644 arch/x86/cpu/apollolake/punit.c