@@ -331,7 +331,7 @@ config X86_RAMTEST
config FLASH_DESCRIPTOR_FILE
string "Flash descriptor binary filename"
- depends on HAVE_INTEL_ME
+ depends on HAVE_INTEL_ME || FSP_VERSION2
default "descriptor.bin"
help
The filename of the file to use as flash descriptor in the
@@ -416,6 +416,45 @@ config FSP_ADDR
The default base address of 0xfffc0000 indicates that the binary must
be located at offset 0xc0000 from the beginning of a 1MB flash device.
+if FSP_VERSION2
+
+config FSP_FILE_T
+ string "Firmware-Support-Package binary filename (Temp RAM)"
+ default "fsp_t.bin"
+ help
+ The filename of the file to use for the temporary-RAM init phase from
+ the Firmware-Support-Package binary. Put this in the board directory.
+ It is used to set up an initial area of RAM which can be used for the
+ stack and other purposes, while bringing up the main system DRAM.
+
+config FSP_ADDR_T
+ hex "Firmware-Support-Package binary location (Temp RAM)"
+ default 0xffff8000
+ help
+ FSP is not Position-Independent Code (PIC) and FSP components have to
+ be rebased if placed at a location which is different from the
+ perferred base address specified during the FSP build. Use Intel's
+ Binary Configuration Tool (BCT) to do the rebase.
+
+config FSP_FILE_M
+ string "Firmware-Support-Package binary filename (Memory Init)"
+ default "fsp_m.bin"
+ help
+ The filename of the file to use for the RAM init phase from the
+ Firmware Support Package binary. Put this in the board directory.
+ It is used to set up an initial area of RAM which can be used for the
+ stack and other purposes, while bringing up the main system DRAM.
+
+config IFWI_INPUT_FILE
+ string "Filename containing FIT (Firmware Interface Table) with IFWI"
+ default "fitimage.bin"
+ help
+ The IFWI is obtained by running a tool on this file to extract the
+ IFWI. Put this in the board directory. The IFWI contains U-Boot TPL,
+ microcode and other internal items.
+
+endif
+
config FSP_TEMP_RAM_ADDR
hex
depends on FSP_VERSION1
new file mode 100644
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: Intel */
+/*
+ * Copyright (C) 2015-2016 Intel Corp.
+ * (Written by Andrey Petrov <andrey.petrov@intel.com> for Intel Corp.)
+ * (Written by Alexandru Gagniuc <alexandrux.gagniuc@intel.com> for Intel Corp.)
+ * Mostly taken from coreboot fsp2_0/memory_init.c
+ */
+
+#ifndef __ASM_FSP_API_H
+#define __ASM_FSP_API_H
+
+struct fspm_upd;
+struct hob_header;
+
+enum fsp_boot_mode {
+ FSP_BOOT_WITH_FULL_CONFIGURATION = 0x00,
+ FSP_BOOT_WITH_MINIMAL_CONFIGURATION = 0x01,
+ FSP_BOOT_ASSUMING_NO_CONFIGURATION_CHANGES = 0x02,
+ FSP_BOOT_ON_S4_RESUME = 0x05,
+ FSP_BOOT_ON_S3_RESUME = 0x11,
+ FSP_BOOT_ON_FLASH_UPDATE = 0x12,
+ FSP_BOOT_IN_RECOVERY_MODE = 0x20
+};
+
+/**
+ * fsp_memory_init() - Init the SDRAM
+ *
+ * @s3wake: true if we are booting from resume, so cannot reinit the mememory
+ * from scatch since we will lose its contents
+ * @use_spi_flash: true to use the fast SPI driver to read FSP, otherwise use
+ * mapped SPI
+ */
+int fsp_memory_init(bool s3wake, bool use_spi_flash);
+
+typedef asmlinkage int (*fsp_memory_init_func)(struct fspm_upd *params,
+ struct hob_header **hobp);
+
+#endif
new file mode 100644
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: Intel */
+/*
+ * Copyright (C) 2015-2016 Intel Corp.
+ * (Written by Alexandru Gagniuc <alexandrux.gagniuc@intel.com> for Intel Corp.)
+ * Mostly taken from coreboot
+ */
+
+#ifndef __ASM_FSP_INTERNAL_H
+#define __ASM_FSP_INTERNAL_H
+
+struct fsp_header;
+
+int fsp_get_header(ulong offset, ulong size, bool use_spi_flash,
+ struct fsp_header **fspp, ulong *basep);
+
+#endif
new file mode 100644
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright 2019 Google LLC
+
+obj-y += fsp_dram.o
+obj-y += fsp_meminit.o
+obj-y += fsp_support.o
new file mode 100644
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 Google LLC
+ * Written by Simon Glass <sjg@chromium.org>
+ */
+
+#include <common.h>
+#include <acpi_s3.h>
+#include <handoff.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/fsp/fsp_support.h>
+#include <asm/fsp2/fsp_api.h>
+
+int dram_init(void)
+{
+ int ret;
+
+ if (spl_phase() == PHASE_SPL) {
+#ifdef CONFIG_HAVE_ACPI_RESUME
+ bool s3wake = gd->arch.prev_sleep_state == ACPI_S3;
+#else
+ bool s3wake = false;
+#endif
+
+ ret = fsp_memory_init(s3wake, BOOT_FROM_FAST_SPI_FLASH);
+ if (ret) {
+ debug("Memory init failed (err=%x)\n", ret);
+ return ret;
+ }
+
+ /* The FSP has already set up DRAM, so grab the info we need */
+ ret = fsp_scan_for_ram_size();
+ if (ret)
+ return ret;
+
+#ifdef CONFIG_ENABLE_MRC_CACHE
+ gd->arch.mrc[MRC_TYPE_NORMAL].buf =
+ fsp_get_nvs_data(gd->arch.hob_list,
+ &gd->arch.mrc[MRC_TYPE_NORMAL].len);
+ gd->arch.mrc[MRC_TYPE_VAR].buf =
+ fsp_get_var_nvs_data(gd->arch.hob_list,
+ &gd->arch.mrc[MRC_TYPE_VAR].len);
+ log_debug("normal %x, var %x\n",
+ gd->arch.mrc[MRC_TYPE_NORMAL].len,
+ gd->arch.mrc[MRC_TYPE_VAR].len);
+#endif
+ } else {
+#if CONFIG_IS_ENABLED(HANDOFF)
+ struct spl_handoff *ho = gd->spl_handoff;
+
+ if (!ho) {
+ debug("No SPL handoff found\n");
+ return -ESTRPIPE;
+ }
+ gd->ram_size = ho->ram_size;
+ handoff_load_dram_banks(ho);
+#endif
+ }
+
+ return 0;
+}
+
+ulong board_get_usable_ram_top(ulong total_size)
+{
+#if CONFIG_IS_ENABLED(HANDOFF)
+ struct spl_handoff *ho = gd->spl_handoff;
+
+ return ho->arch.usable_ram_top;
+#endif
+
+ return gd->ram_top;
+}
new file mode 100644
@@ -0,0 +1,344 @@
+// SPDX-License-Identifier: Intel
+/*
+ * Copyright (C) 2015-2016 Intel Corp.
+ * (Written by Andrey Petrov <andrey.petrov@intel.com> for Intel Corp.)
+ * (Written by Alexandru Gagniuc <alexandrux.gagniuc@intel.com> for Intel Corp.)
+ * Mostly taken from coreboot fsp2_0/memory_init.c
+ */
+
+#include <common.h>
+#include <binman_sym.h>
+#include <cbfs.h>
+#include <dm.h>
+#include <spi_flash.h>
+#include <asm/mrccache.h>
+#include <asm/hob.h>
+#include <asm/fsp/fsp_infoheader.h>
+#include <asm/fsp2/fsp_api.h>
+#include <asm/fsp2/fsp_internal.h>
+#include <asm/arch/fsp/fsp_configs.h>
+#include <asm/arch/fsp/fsp_m_upd.h>
+
+binman_sym_declare(ulong, intel_fsp_m, image_pos);
+binman_sym_declare(ulong, intel_fsp_m, size);
+
+/*
+ * ODT settings:
+ * If ODT PIN to LP4 DRAM is pulled HIGH for ODT_A and HIGH for ODT_B,
+ * choose ODT_A_B_HIGH_HIGH. If ODT PIN to LP4 DRAM is pulled HIGH for ODT_A
+ * and LOW for ODT_B, choose ODT_A_B_HIGH_LOW.
+ *
+ * Note that the enum values correspond to the interpreted UPD fields
+ * within Ch[3:0]_OdtConfig parameters.
+ */
+enum {
+ ODT_A_B_HIGH_LOW = 0 << 1,
+ ODT_A_B_HIGH_HIGH = 1 << 1,
+ N_WR_24 = 1 << 5,
+};
+
+/*
+ * LPDDR4 helper routines for configuring the memory UPD for LPDDR4 operation.
+ * There are four physical LPDDR4 channels, each 32-bits wide. There are two
+ * logical channels using two physical channels together to form a 64-bit
+ * interface to memory for each logical channel.
+ */
+
+enum {
+ LP4_PHYS_CH0A,
+ LP4_PHYS_CH0B,
+ LP4_PHYS_CH1A,
+ LP4_PHYS_CH1B,
+
+ LP4_NUM_PHYS_CHANNELS,
+};
+
+/*
+ * The DQs within a physical channel can be bit-swizzled within each byte.
+ * Within a channel the bytes can be swapped, but the DQs need to be routed
+ * with the corresponding DQS (strobe).
+ */
+enum {
+ LP4_DQS0,
+ LP4_DQS1,
+ LP4_DQS2,
+ LP4_DQS3,
+
+ LP4_NUM_BYTE_LANES,
+ DQ_BITS_PER_DQS = 8,
+};
+
+/* Provide bit swizzling per DQS and byte swapping within a channel. */
+struct lpddr4_chan_swizzle_cfg {
+ u8 dqs[LP4_NUM_BYTE_LANES][DQ_BITS_PER_DQS];
+};
+
+struct lpddr4_swizzle_cfg {
+ struct lpddr4_chan_swizzle_cfg phys[LP4_NUM_PHYS_CHANNELS];
+};
+
+static int prepare_mrc_cache_type(enum mrc_type_t type,
+ struct mrc_data_container **cachep)
+{
+ struct mrc_data_container *cache;
+ struct mrc_region entry;
+ int ret;
+
+ ret = mrccache_get_region(type, NULL, &entry);
+ if (ret)
+ return ret;
+ cache = mrccache_find_current(&entry);
+ if (!cache)
+ return -ENOENT;
+
+ log_debug("MRC at %x, size %x\n", (uint)cache->data, cache->data_size);
+ *cachep = cache;
+
+ return 0;
+}
+
+static int prepare_mrc_cache(struct fspm_upd *upd)
+{
+ struct mrc_data_container *cache;
+ int ret;
+
+ ret = prepare_mrc_cache_type(MRC_TYPE_NORMAL, &cache);
+ if (ret)
+ return log_msg_ret("Cannot get normal cache", ret);
+ upd->arch.nvs_buffer_ptr = cache->data;
+
+ ret = prepare_mrc_cache_type(MRC_TYPE_VAR, &cache);
+ if (ret)
+ return log_msg_ret("Cannot get var cache", ret);
+ upd->config.variable_nvs_buffer_ptr = cache->data;
+
+ return 0;
+}
+
+static int get_coreboot_fsp(ulong map_base, ulong *fsp_m_posp,
+ ulong *fsp_m_sizep)
+{
+ /* Hard-coded position of CBFS in ROM */
+ ulong cbfs_base = 0x205000;
+ ulong cbfs_size = 0x1bb000;
+ struct cbfs_priv *cbfs;
+ int ret;
+
+ ret = cbfs_init_mem(map_base + cbfs_base, cbfs_size, &cbfs);
+ if (ret)
+ return ret;
+ if (!ret) {
+ const struct cbfs_cachenode *node;
+
+ node = cbfs_find_file(cbfs, "fspm.bin");
+ if (!node) {
+ printf("no node\n");
+ return -ENOENT;
+ }
+
+ *fsp_m_posp = (ulong)node->data;
+ *fsp_m_sizep = node->data_length;
+ }
+
+ return 0;
+}
+
+static void setup_sdram(struct fsp_m_config *cfg,
+ const struct lpddr4_swizzle_cfg *swizzle_cfg)
+{
+ const struct lpddr4_chan_swizzle_cfg *sch;
+ /* Number of bytes to copy per DQS. */
+ const size_t sz = DQ_BITS_PER_DQS;
+ int chan;
+
+ cfg->memory_down = 1;
+ cfg->scrambler_support = 1;
+ cfg->channel_hash_mask = 0x36;
+ cfg->slice_hash_mask = 9;
+ cfg->interleaved_mode = 2;
+ cfg->channels_slices_enable = 0;
+ cfg->min_ref_rate2x_enable = 0;
+ cfg->dual_rank_support_enable = 1;
+
+ /* LPDDR4 is memory down so no SPD addresses. */
+ cfg->dimm0_spd_address = 0;
+ cfg->dimm1_spd_address = 0;
+
+ for (chan = 0; chan < 4; chan++) {
+ struct fsp_ram_channel *ch = &cfg->chan[chan];
+
+ ch->rank_enable = 1;
+ ch->device_width = 1;
+ ch->dram_density = 2;
+ ch->option = 3;
+ ch->odt_config = ODT_A_B_HIGH_HIGH;
+ }
+
+ /*
+ * CH0_DQB byte lanes in the bit swizzle configuration field are
+ * not 1:1. The mapping within the swizzling field is:
+ * indices [0:7] - byte lane 1 (DQS1) DQ[8:15]
+ * indices [8:15] - byte lane 0 (DQS0) DQ[0:7]
+ * indices [16:23] - byte lane 3 (DQS3) DQ[24:31]
+ * indices [24:31] - byte lane 2 (DQS2) DQ[16:23]
+ */
+ sch = &swizzle_cfg->phys[LP4_PHYS_CH0B];
+ memcpy(&cfg->ch_bit_swizzling[0][0], &sch->dqs[LP4_DQS1], sz);
+ memcpy(&cfg->ch_bit_swizzling[0][8], &sch->dqs[LP4_DQS0], sz);
+ memcpy(&cfg->ch_bit_swizzling[0][16], &sch->dqs[LP4_DQS3], sz);
+ memcpy(&cfg->ch_bit_swizzling[0][24], &sch->dqs[LP4_DQS2], sz);
+
+ /*
+ * CH0_DQA byte lanes in the bit swizzle configuration field are 1:1.
+ */
+ sch = &swizzle_cfg->phys[LP4_PHYS_CH0A];
+ memcpy(&cfg->ch_bit_swizzling[1][0], &sch->dqs[LP4_DQS0], sz);
+ memcpy(&cfg->ch_bit_swizzling[1][8], &sch->dqs[LP4_DQS1], sz);
+ memcpy(&cfg->ch_bit_swizzling[1][16], &sch->dqs[LP4_DQS2], sz);
+ memcpy(&cfg->ch_bit_swizzling[1][24], &sch->dqs[LP4_DQS3], sz);
+
+ sch = &swizzle_cfg->phys[LP4_PHYS_CH1B];
+ memcpy(&cfg->ch_bit_swizzling[2][0], &sch->dqs[LP4_DQS1], sz);
+ memcpy(&cfg->ch_bit_swizzling[2][8], &sch->dqs[LP4_DQS0], sz);
+ memcpy(&cfg->ch_bit_swizzling[2][16], &sch->dqs[LP4_DQS3], sz);
+ memcpy(&cfg->ch_bit_swizzling[2][24], &sch->dqs[LP4_DQS2], sz);
+
+ /*
+ * CH0_DQA byte lanes in the bit swizzle configuration field are 1:1.
+ */
+ sch = &swizzle_cfg->phys[LP4_PHYS_CH1A];
+ memcpy(&cfg->ch_bit_swizzling[3][0], &sch->dqs[LP4_DQS0], sz);
+ memcpy(&cfg->ch_bit_swizzling[3][8], &sch->dqs[LP4_DQS1], sz);
+ memcpy(&cfg->ch_bit_swizzling[3][16], &sch->dqs[LP4_DQS2], sz);
+ memcpy(&cfg->ch_bit_swizzling[3][24], &sch->dqs[LP4_DQS3], sz);
+}
+
+/**
+ * setup_config() - Set up the config structure for FSP-M
+ *
+ * @dev: Hostbridge device containing config
+ * @upd: Config data to fill in
+ * @return 0 if OK, -ve on error
+ */
+static int setup_config(struct udevice *dev, struct fspm_upd *upd)
+{
+ struct fsp_m_config *cfg = &upd->config;
+ struct fspm_arch_upd *arch = &upd->arch;
+
+ arch->nvs_buffer_ptr = NULL;
+ prepare_mrc_cache(upd);
+ arch->stack_base = (void *)0xfef96000;
+ arch->boot_loader_tolum_size = 0x2000;
+
+ arch->boot_mode = FSP_BOOT_WITH_FULL_CONFIGURATION;
+ cfg->serial_debug_port_type = 2;
+ cfg->serial_debug_port_device = 2;
+ cfg->serial_debug_port_stride_size = 2;
+ cfg->serial_debug_port_address = 0;
+
+ cfg->package = 1;
+ /* Don't enforce a memory size limit. */
+ cfg->memory_size_limit = 0;
+ cfg->low_memory_max_value = 2048; /* 2 GB */
+ /* No restrictions on memory above 4GiB */
+ cfg->high_memory_max_value = 0;
+
+ /* Always default to attempt to use saved training data. */
+ cfg->disable_fast_boot = 0;
+
+ const u8 *swizzle_data;
+
+ swizzle_data = dev_read_u8_array_ptr(dev, "lpddr4-swizzle",
+ LP4_NUM_BYTE_LANES *
+ DQ_BITS_PER_DQS *
+ LP4_NUM_PHYS_CHANNELS);
+ if (!swizzle_data)
+ return log_msg_ret("Cannot read swizzel data", -EINVAL);
+
+ setup_sdram(cfg, (struct lpddr4_swizzle_cfg *)swizzle_data);
+
+ cfg->pre_mem_gpio_table_ptr = 0;
+
+ cfg->profile = 0xb;
+ cfg->msg_level_mask = 0;
+
+ /* other */
+ cfg->skip_cse_rbp = 1;
+ cfg->periodic_retraining_disable = 0;
+ cfg->enable_s3_heci2 = 0;
+
+ return 0;
+}
+
+int fsp_memory_init(bool s3wake, bool use_spi_flash)
+{
+ struct fspm_upd upd, *fsp_upd;
+ fsp_memory_init_func func;
+ struct fsp_header *hdr;
+ struct hob_header *hob;
+ struct udevice *dev, *sf;
+ ulong fsp_m_pos = 0;
+ ulong fsp_m_size = 0;
+ size_t map_size;
+ ulong map_base;
+ ulong base;
+ u32 offset;
+ int ret;
+
+ ret = uclass_first_device_err(UCLASS_NORTHBRIDGE, &dev);
+ if (ret)
+ return log_msg_ret("Cannot get northbridge", ret);
+ ret = uclass_first_device_err(UCLASS_SPI_FLASH, &sf);
+ if (ret)
+ return log_msg_ret("Cannot get SPI flash", ret);
+ ret = spi_flash_get_mmap(sf, &map_base, &map_size, &offset);
+ if (ret)
+ return log_msg_ret("Could not get flash mmap", ret);
+
+ ret = -ENOENT;
+ if (false)
+ /* Support using a hybrid image build by coreboot */
+ ret = get_coreboot_fsp(map_base, &fsp_m_pos, &fsp_m_size);
+ if (ret) {
+ ulong mask = CONFIG_ROM_SIZE - 1;
+
+ fsp_m_pos = binman_sym(ulong, intel_fsp_m, image_pos);
+ fsp_m_size = binman_sym(ulong, intel_fsp_m, size);
+ if (fsp_m_pos != BINMAN_SYM_MISSING) {
+ ret = 0;
+ if (use_spi_flash)
+ fsp_m_pos &= mask;
+ else
+ fsp_m_pos += (map_base & mask);
+ } else {
+ ret = -ENOENT;
+ }
+ }
+ if (ret)
+ return log_msg_ret("Cannot find FSP_M", ret);
+
+ /* Use memory-mapped SPI flash by default as it is simpler */
+ ret = fsp_get_header(fsp_m_pos, fsp_m_size, use_spi_flash, &hdr, &base);
+ if (ret)
+ return log_msg_ret("fsp_get_header", ret);
+
+ /* Copy over the default config */
+ fsp_upd = (struct fspm_upd *)(base + hdr->cfg_region_off);
+ if (fsp_upd->header.signature != FSPM_UPD_SIGNATURE)
+ return log_msg_ret("Bad UPD signature", -EPERM);
+ memcpy(&upd, fsp_upd, sizeof(upd));
+
+ ret = setup_config(dev, &upd);
+ if (ret)
+ return log_msg_ret("Could not setup config", ret);
+ debug("SDRAM init...");
+ func = (fsp_memory_init_func)(base + hdr->fsp_mem_init);
+ ret = func(&upd, &hob);
+ if (ret)
+ return log_msg_ret("SDRAM init fail\n", ret);
+
+ gd->arch.hob_list = hob;
+ debug("done\n");
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: Intel
+/*
+ * Copyright 2019 Google LLC
+ * Written by Simon Glass <sjg@chromium.org>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <spi_flash.h>
+#include <asm/fsp/fsp_support.h>
+#include <asm/fsp2/fsp_internal.h>
+
+/* The amount of the FSP header to probe to obtain what we need */
+#define PROBE_BUF_SIZE 0x180
+
+/* Not needed in SPL apparently */
+#define SAFETY_MARGIN 0
+
+int fsp_get_header(ulong offset, ulong size, bool use_spi_flash,
+ struct fsp_header **fspp, ulong *basep)
+{
+ static efi_guid_t guid = FSP_HEADER_GUID;
+ struct fv_ext_header *exhdr;
+ struct fsp_header *fsp;
+ struct ffs_file_header *file_hdr;
+ struct fv_header *fv;
+ struct raw_section *raw;
+ void *ptr, *base;
+ u8 buf[PROBE_BUF_SIZE];
+ struct udevice *dev;
+ int ret;
+
+ /* You are in a maze of twisty headers all alike */
+ debug("offset=%x buf=%x\n", (uint)offset, (uint)buf);
+ if (use_spi_flash) {
+ ret = uclass_first_device_err(UCLASS_SPI_FLASH, &dev);
+ if (ret)
+ return log_msg_ret("Cannot find flash device", ret);
+ ret = spi_flash_read_dm(dev, offset, PROBE_BUF_SIZE, buf);
+ if (ret)
+ return log_msg_ret("Cannot read flash", ret);
+ } else {
+ memcpy(buf, (void *)offset, PROBE_BUF_SIZE);
+ }
+
+ /* Initalise the FSP base */
+ ptr = buf;
+ fv = ptr;
+
+ /* Check the FV signature, _FVH */
+ debug("offset=%x sign=%x\n", (uint)offset, (uint)fv->sign);
+ if (fv->sign != EFI_FVH_SIGNATURE)
+ return log_msg_ret("Base FV signature", -EINVAL);
+
+ /* Go to the end of the FV header and align the address */
+ debug("fv->ext_hdr_off = %x\n", fv->ext_hdr_off);
+ ptr += fv->ext_hdr_off;
+ exhdr = ptr;
+ ptr += ALIGN(exhdr->ext_hdr_size, 8);
+ debug("ptr=%x\n", ptr - (void *)buf);
+
+ /* Check the FFS GUID */
+ file_hdr = ptr;
+ if (memcmp(&file_hdr->name, &guid, sizeof(guid)))
+ return log_msg_ret("Base FFS GUID", -ENXIO);
+ /* Add the FFS header size to find the raw section header */
+ ptr = file_hdr + 1;
+
+ raw = ptr;
+ debug("raw->type = %x\n", raw->type);
+ if (raw->type != EFI_SECTION_RAW)
+ return log_msg_ret("Section type not RAW", -ENOEXEC);
+
+ /* Add the raw section header size to find the FSP header */
+ ptr = raw + 1;
+ fsp = ptr;
+
+ /* Check the FSPH header */
+ debug("fsp %x\n", (uint)fsp);
+ if (fsp->sign != EFI_FSPH_SIGNATURE)
+ return log_msg_ret("Base FSPH signature", -EACCES);
+
+ base = (void *)fsp->img_base;
+ debug("Image base %x\n", (uint)base);
+ debug("Image addr %x\n", (uint)fsp->fsp_mem_init);
+ if (use_spi_flash) {
+ ret = spi_flash_read_dm(dev, offset, size + SAFETY_MARGIN,
+ base);
+ if (ret)
+ return log_msg_ret("Could not read FPS-M", ret);
+ } else {
+ memcpy(base, (void *)offset, size + SAFETY_MARGIN);
+ }
+ ptr = base + (ptr - (void *)buf);
+ *fspp = ptr;
+ *basep = fsp->img_base;
+
+ return 0;
+}
+
+int arch_fsp_init(void)
+{
+ return 0;
+}
+
+u32 fsp_notify(struct fsp_header *fsp_hdr, u32 phase)
+{
+ return 0;
+}
Add support for some important configuration options and FSP memory init. The memory init uses swizzle tables from the device tree. Note that support for the FSP_S binary is not yet included. Signed-off-by: Simon Glass <sjg@chromium.org> --- arch/x86/Kconfig | 41 ++- arch/x86/include/asm/fsp2/fsp_api.h | 38 +++ arch/x86/include/asm/fsp2/fsp_internal.h | 16 ++ arch/x86/lib/fsp2/Makefile | 7 + arch/x86/lib/fsp2/fsp_dram.c | 73 +++++ arch/x86/lib/fsp2/fsp_meminit.c | 344 +++++++++++++++++++++++ arch/x86/lib/fsp2/fsp_support.c | 109 +++++++ 7 files changed, 627 insertions(+), 1 deletion(-) create mode 100644 arch/x86/include/asm/fsp2/fsp_api.h create mode 100644 arch/x86/include/asm/fsp2/fsp_internal.h create mode 100644 arch/x86/lib/fsp2/Makefile create mode 100644 arch/x86/lib/fsp2/fsp_dram.c create mode 100644 arch/x86/lib/fsp2/fsp_meminit.c create mode 100644 arch/x86/lib/fsp2/fsp_support.c