@@ -8400,12 +8400,6 @@ L: linux-mips@vger.kernel.org
S: Maintained
F: drivers/net/ethernet/sgi/ioc3-eth.c
-IOC3 SERIAL DRIVER
-M: Pat Gefre <pfg@sgi.com>
-L: linux-serial@vger.kernel.org
-S: Maintained
-F: drivers/tty/serial/ioc3_serial.c
-
IOMAP FILESYSTEM LIBRARY
M: Christoph Hellwig <hch@infradead.org>
M: Darrick J. Wong <darrick.wong@oracle.com>
@@ -83,7 +83,6 @@ CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=6
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
-CONFIG_SERIAL_SGI_IOC3=y
# CONFIG_HW_RANDOM is not set
CONFIG_EFI_RTC=y
CONFIG_RAW_DRIVER=m
@@ -972,14 +972,6 @@ config SERIAL_JSM
To compile this driver as a module, choose M here: the
module will be called jsm.
-config SERIAL_SGI_IOC3
- tristate "SGI Altix IOC3 serial support"
- depends on (IA64_GENERIC || IA64_SGI_SN2) && SGI_IOC3
- select SERIAL_CORE
- help
- If you have an SGI Altix with an IOC3 serial card,
- say Y or M. Otherwise, say N.
-
config SERIAL_MSM
tristate "MSM on-chip serial port support"
depends on ARCH_QCOM
@@ -52,7 +52,6 @@ obj-$(CONFIG_SERIAL_SC16IS7XX_CORE) += sc16is7xx.o
obj-$(CONFIG_SERIAL_JSM) += jsm/
obj-$(CONFIG_SERIAL_TXX9) += serial_txx9.o
obj-$(CONFIG_SERIAL_VR41XX) += vr41xx_siu.o
-obj-$(CONFIG_SERIAL_SGI_IOC3) += ioc3_serial.o
obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
obj-$(CONFIG_SERIAL_UARTLITE) += uartlite.o
obj-$(CONFIG_SERIAL_MSM) += msm_serial.o
deleted file mode 100644
@@ -1,2195 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2005 Silicon Graphics, Inc. All Rights Reserved.
- */
-
-/*
- * This file contains a module version of the ioc3 serial driver. This
- * includes all the support functions needed (support functions, etc.)
- * and the serial driver itself.
- */
-#include <linux/errno.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial.h>
-#include <linux/circ_buf.h>
-#include <linux/serial_reg.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/serial_core.h>
-#include <linux/ioc3.h>
-#include <linux/slab.h>
-
-/*
- * Interesting things about the ioc3
- */
-
-#define LOGICAL_PORTS 2 /* rs232(0) and rs422(1) */
-#define PORTS_PER_CARD 2
-#define LOGICAL_PORTS_PER_CARD (PORTS_PER_CARD * LOGICAL_PORTS)
-#define MAX_CARDS 8
-#define MAX_LOGICAL_PORTS (LOGICAL_PORTS_PER_CARD * MAX_CARDS)
-
-/* determine given the sio_ir what port it applies to */
-#define GET_PORT_FROM_SIO_IR(_x) (_x & SIO_IR_SA) ? 0 : 1
-
-
-/*
- * we have 2 logical ports (rs232, rs422) for each physical port
- * evens are rs232, odds are rs422
- */
-#define GET_PHYSICAL_PORT(_x) ((_x) >> 1)
-#define GET_LOGICAL_PORT(_x) ((_x) & 1)
-#define IS_PHYSICAL_PORT(_x) !((_x) & 1)
-#define IS_RS232(_x) !((_x) & 1)
-
-static unsigned int Num_of_ioc3_cards;
-static unsigned int Submodule_slot;
-
-/* defining this will get you LOTS of great debug info */
-//#define DEBUG_INTERRUPTS
-#define DPRINT_CONFIG(_x...) ;
-//#define DPRINT_CONFIG(_x...) printk _x
-#define NOT_PROGRESS() ;
-//#define NOT_PROGRESS() printk("%s : fails %d\n", __func__, __LINE__)
-
-/* number of characters we want to transmit to the lower level at a time */
-#define MAX_CHARS 256
-#define FIFO_SIZE (MAX_CHARS-1) /* it's a uchar */
-
-/* Device name we're using */
-#define DEVICE_NAME "ttySIOC"
-#define DEVICE_MAJOR 204
-#define DEVICE_MINOR 116
-
-/* flags for next_char_state */
-#define NCS_BREAK 0x1
-#define NCS_PARITY 0x2
-#define NCS_FRAMING 0x4
-#define NCS_OVERRUN 0x8
-
-/* cause we need SOME parameters ... */
-#define MIN_BAUD_SUPPORTED 1200
-#define MAX_BAUD_SUPPORTED 115200
-
-/* protocol types supported */
-#define PROTO_RS232 0
-#define PROTO_RS422 1
-
-/* Notification types */
-#define N_DATA_READY 0x01
-#define N_OUTPUT_LOWAT 0x02
-#define N_BREAK 0x04
-#define N_PARITY_ERROR 0x08
-#define N_FRAMING_ERROR 0x10
-#define N_OVERRUN_ERROR 0x20
-#define N_DDCD 0x40
-#define N_DCTS 0x80
-
-#define N_ALL_INPUT (N_DATA_READY | N_BREAK \
- | N_PARITY_ERROR | N_FRAMING_ERROR \
- | N_OVERRUN_ERROR | N_DDCD | N_DCTS)
-
-#define N_ALL_OUTPUT N_OUTPUT_LOWAT
-
-#define N_ALL_ERRORS (N_PARITY_ERROR | N_FRAMING_ERROR \
- | N_OVERRUN_ERROR)
-
-#define N_ALL (N_DATA_READY | N_OUTPUT_LOWAT | N_BREAK \
- | N_PARITY_ERROR | N_FRAMING_ERROR \
- | N_OVERRUN_ERROR | N_DDCD | N_DCTS)
-
-#define SER_CLK_SPEED(prediv) ((22000000 << 1) / prediv)
-#define SER_DIVISOR(x, clk) (((clk) + (x) * 8) / ((x) * 16))
-#define DIVISOR_TO_BAUD(div, clk) ((clk) / 16 / (div))
-
-/* Some masks */
-#define LCR_MASK_BITS_CHAR (UART_LCR_WLEN5 | UART_LCR_WLEN6 \
- | UART_LCR_WLEN7 | UART_LCR_WLEN8)
-#define LCR_MASK_STOP_BITS (UART_LCR_STOP)
-
-#define PENDING(_a, _p) (readl(&(_p)->vma->sio_ir) & (_a)->ic_enable)
-
-#define RING_BUF_SIZE 4096
-#define BUF_SIZE_BIT SBBR_L_SIZE
-#define PROD_CONS_MASK PROD_CONS_PTR_4K
-
-#define TOTAL_RING_BUF_SIZE (RING_BUF_SIZE * 4)
-
-/* driver specific - one per card */
-struct ioc3_card {
- struct {
- /* uart ports are allocated here */
- struct uart_port icp_uart_port[LOGICAL_PORTS];
- /* the ioc3_port used for this port */
- struct ioc3_port *icp_port;
- } ic_port[PORTS_PER_CARD];
- /* currently enabled interrupts */
- uint32_t ic_enable;
-};
-
-/* Local port info for each IOC3 serial port */
-struct ioc3_port {
- /* handy reference material */
- struct uart_port *ip_port;
- struct ioc3_card *ip_card;
- struct ioc3_driver_data *ip_idd;
- struct ioc3_submodule *ip_is;
-
- /* pci mem addresses for this port */
- struct ioc3_serialregs __iomem *ip_serial_regs;
- struct ioc3_uartregs __iomem *ip_uart_regs;
-
- /* Ring buffer page for this port */
- dma_addr_t ip_dma_ringbuf;
- /* vaddr of ring buffer */
- struct ring_buffer *ip_cpu_ringbuf;
-
- /* Rings for this port */
- struct ring *ip_inring;
- struct ring *ip_outring;
-
- /* Hook to port specific values */
- struct port_hooks *ip_hooks;
-
- spinlock_t ip_lock;
-
- /* Various rx/tx parameters */
- int ip_baud;
- int ip_tx_lowat;
- int ip_rx_timeout;
-
- /* Copy of notification bits */
- int ip_notify;
-
- /* Shadow copies of various registers so we don't need to PIO
- * read them constantly
- */
- uint32_t ip_sscr;
- uint32_t ip_tx_prod;
- uint32_t ip_rx_cons;
- unsigned char ip_flags;
-};
-
-/* tx low water mark. We need to notify the driver whenever tx is getting
- * close to empty so it can refill the tx buffer and keep things going.
- * Let's assume that if we interrupt 1 ms before the tx goes idle, we'll
- * have no trouble getting in more chars in time (I certainly hope so).
- */
-#define TX_LOWAT_LATENCY 1000
-#define TX_LOWAT_HZ (1000000 / TX_LOWAT_LATENCY)
-#define TX_LOWAT_CHARS(baud) (baud / 10 / TX_LOWAT_HZ)
-
-/* Flags per port */
-#define INPUT_HIGH 0x01
- /* used to signify that we have turned off the rx_high
- * temporarily - we need to drain the fifo and don't
- * want to get blasted with interrupts.
- */
-#define DCD_ON 0x02
- /* DCD state is on */
-#define LOWAT_WRITTEN 0x04
-#define READ_ABORTED 0x08
- /* the read was aborted - used to avaoid infinate looping
- * in the interrupt handler
- */
-#define INPUT_ENABLE 0x10
-
-/* Since each port has different register offsets and bitmasks
- * for everything, we'll store those that we need in tables so we
- * don't have to be constantly checking the port we are dealing with.
- */
-struct port_hooks {
- uint32_t intr_delta_dcd;
- uint32_t intr_delta_cts;
- uint32_t intr_tx_mt;
- uint32_t intr_rx_timer;
- uint32_t intr_rx_high;
- uint32_t intr_tx_explicit;
- uint32_t intr_clear;
- uint32_t intr_all;
- char rs422_select_pin;
-};
-
-static struct port_hooks hooks_array[PORTS_PER_CARD] = {
- /* values for port A */
- {
- .intr_delta_dcd = SIO_IR_SA_DELTA_DCD,
- .intr_delta_cts = SIO_IR_SA_DELTA_CTS,
- .intr_tx_mt = SIO_IR_SA_TX_MT,
- .intr_rx_timer = SIO_IR_SA_RX_TIMER,
- .intr_rx_high = SIO_IR_SA_RX_HIGH,
- .intr_tx_explicit = SIO_IR_SA_TX_EXPLICIT,
- .intr_clear = (SIO_IR_SA_TX_MT | SIO_IR_SA_RX_FULL
- | SIO_IR_SA_RX_HIGH
- | SIO_IR_SA_RX_TIMER
- | SIO_IR_SA_DELTA_DCD
- | SIO_IR_SA_DELTA_CTS
- | SIO_IR_SA_INT
- | SIO_IR_SA_TX_EXPLICIT
- | SIO_IR_SA_MEMERR),
- .intr_all = SIO_IR_SA,
- .rs422_select_pin = GPPR_UARTA_MODESEL_PIN,
- },
-
- /* values for port B */
- {
- .intr_delta_dcd = SIO_IR_SB_DELTA_DCD,
- .intr_delta_cts = SIO_IR_SB_DELTA_CTS,
- .intr_tx_mt = SIO_IR_SB_TX_MT,
- .intr_rx_timer = SIO_IR_SB_RX_TIMER,
- .intr_rx_high = SIO_IR_SB_RX_HIGH,
- .intr_tx_explicit = SIO_IR_SB_TX_EXPLICIT,
- .intr_clear = (SIO_IR_SB_TX_MT | SIO_IR_SB_RX_FULL
- | SIO_IR_SB_RX_HIGH
- | SIO_IR_SB_RX_TIMER
- | SIO_IR_SB_DELTA_DCD
- | SIO_IR_SB_DELTA_CTS
- | SIO_IR_SB_INT
- | SIO_IR_SB_TX_EXPLICIT
- | SIO_IR_SB_MEMERR),
- .intr_all = SIO_IR_SB,
- .rs422_select_pin = GPPR_UARTB_MODESEL_PIN,
- }
-};
-
-struct ring_entry {
- union {
- struct {
- uint32_t alldata;
- uint32_t allsc;
- } all;
- struct {
- char data[4]; /* data bytes */
- char sc[4]; /* status/control */
- } s;
- } u;
-};
-
-/* Test the valid bits in any of the 4 sc chars using "allsc" member */
-#define RING_ANY_VALID \
- ((uint32_t)(RXSB_MODEM_VALID | RXSB_DATA_VALID) * 0x01010101)
-
-#define ring_sc u.s.sc
-#define ring_data u.s.data
-#define ring_allsc u.all.allsc
-
-/* Number of entries per ring buffer. */
-#define ENTRIES_PER_RING (RING_BUF_SIZE / (int) sizeof(struct ring_entry))
-
-/* An individual ring */
-struct ring {
- struct ring_entry entries[ENTRIES_PER_RING];
-};
-
-/* The whole enchilada */
-struct ring_buffer {
- struct ring TX_A;
- struct ring RX_A;
- struct ring TX_B;
- struct ring RX_B;
-};
-
-/* Get a ring from a port struct */
-#define RING(_p, _wh) &(((struct ring_buffer *)((_p)->ip_cpu_ringbuf))->_wh)
-
-/* for Infinite loop detection */
-#define MAXITER 10000000
-
-
-/**
- * set_baud - Baud rate setting code
- * @port: port to set
- * @baud: baud rate to use
- */
-static int set_baud(struct ioc3_port *port, int baud)
-{
- int divisor;
- int actual_baud;
- int diff;
- int lcr, prediv;
- struct ioc3_uartregs __iomem *uart;
-
- for (prediv = 6; prediv < 64; prediv++) {
- divisor = SER_DIVISOR(baud, SER_CLK_SPEED(prediv));
- if (!divisor)
- continue; /* invalid divisor */
- actual_baud = DIVISOR_TO_BAUD(divisor, SER_CLK_SPEED(prediv));
-
- diff = actual_baud - baud;
- if (diff < 0)
- diff = -diff;
-
- /* if we're within 1% we've found a match */
- if (diff * 100 <= actual_baud)
- break;
- }
-
- /* if the above loop completed, we didn't match
- * the baud rate. give up.
- */
- if (prediv == 64) {
- NOT_PROGRESS();
- return 1;
- }
-
- uart = port->ip_uart_regs;
- lcr = readb(&uart->iu_lcr);
-
- writeb(lcr | UART_LCR_DLAB, &uart->iu_lcr);
- writeb((unsigned char)divisor, &uart->iu_dll);
- writeb((unsigned char)(divisor >> 8), &uart->iu_dlm);
- writeb((unsigned char)prediv, &uart->iu_scr);
- writeb((unsigned char)lcr, &uart->iu_lcr);
-
- return 0;
-}
-
-/**
- * get_ioc3_port - given a uart port, return the control structure
- * @the_port: uart port to find
- */
-static struct ioc3_port *get_ioc3_port(struct uart_port *the_port)
-{
- struct ioc3_driver_data *idd = dev_get_drvdata(the_port->dev);
- struct ioc3_card *card_ptr = idd->data[Submodule_slot];
- int ii, jj;
-
- if (!card_ptr) {
- NOT_PROGRESS();
- return NULL;
- }
- for (ii = 0; ii < PORTS_PER_CARD; ii++) {
- for (jj = 0; jj < LOGICAL_PORTS; jj++) {
- if (the_port == &card_ptr->ic_port[ii].icp_uart_port[jj])
- return card_ptr->ic_port[ii].icp_port;
- }
- }
- NOT_PROGRESS();
- return NULL;
-}
-
-/**
- * port_init - Initialize the sio and ioc3 hardware for a given port
- * called per port from attach...
- * @port: port to initialize
- */
-static inline int port_init(struct ioc3_port *port)
-{
- uint32_t sio_cr;
- struct port_hooks *hooks = port->ip_hooks;
- struct ioc3_uartregs __iomem *uart;
- int reset_loop_counter = 0xfffff;
- struct ioc3_driver_data *idd = port->ip_idd;
-
- /* Idle the IOC3 serial interface */
- writel(SSCR_RESET, &port->ip_serial_regs->sscr);
-
- /* Wait until any pending bus activity for this port has ceased */
- do {
- sio_cr = readl(&idd->vma->sio_cr);
- if (reset_loop_counter-- <= 0) {
- printk(KERN_WARNING
- "IOC3 unable to come out of reset"
- " scr 0x%x\n", sio_cr);
- return -1;
- }
- } while (!(sio_cr & SIO_CR_ARB_DIAG_IDLE) &&
- (((sio_cr &= SIO_CR_ARB_DIAG) == SIO_CR_ARB_DIAG_TXA)
- || sio_cr == SIO_CR_ARB_DIAG_TXB
- || sio_cr == SIO_CR_ARB_DIAG_RXA
- || sio_cr == SIO_CR_ARB_DIAG_RXB));
-
- /* Finish reset sequence */
- writel(0, &port->ip_serial_regs->sscr);
-
- /* Once RESET is done, reload cached tx_prod and rx_cons values
- * and set rings to empty by making prod == cons
- */
- port->ip_tx_prod = readl(&port->ip_serial_regs->stcir) & PROD_CONS_MASK;
- writel(port->ip_tx_prod, &port->ip_serial_regs->stpir);
- port->ip_rx_cons = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
- writel(port->ip_rx_cons | SRCIR_ARM, &port->ip_serial_regs->srcir);
-
- /* Disable interrupts for this 16550 */
- uart = port->ip_uart_regs;
- writeb(0, &uart->iu_lcr);
- writeb(0, &uart->iu_ier);
-
- /* Set the default baud */
- set_baud(port, port->ip_baud);
-
- /* Set line control to 8 bits no parity */
- writeb(UART_LCR_WLEN8 | 0, &uart->iu_lcr);
- /* UART_LCR_STOP == 1 stop */
-
- /* Enable the FIFOs */
- writeb(UART_FCR_ENABLE_FIFO, &uart->iu_fcr);
- /* then reset 16550 FIFOs */
- writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
- &uart->iu_fcr);
-
- /* Clear modem control register */
- writeb(0, &uart->iu_mcr);
-
- /* Clear deltas in modem status register */
- writel(0, &port->ip_serial_regs->shadow);
-
- /* Only do this once per port pair */
- if (port->ip_hooks == &hooks_array[0]) {
- unsigned long ring_pci_addr;
- uint32_t __iomem *sbbr_l, *sbbr_h;
-
- sbbr_l = &idd->vma->sbbr_l;
- sbbr_h = &idd->vma->sbbr_h;
- ring_pci_addr = (unsigned long __iomem)port->ip_dma_ringbuf;
- DPRINT_CONFIG(("%s: ring_pci_addr 0x%p\n",
- __func__, (void *)ring_pci_addr));
-
- writel((unsigned int)((uint64_t) ring_pci_addr >> 32), sbbr_h);
- writel((unsigned int)ring_pci_addr | BUF_SIZE_BIT, sbbr_l);
- }
-
- /* Set the receive timeout value to 10 msec */
- writel(SRTR_HZ / 100, &port->ip_serial_regs->srtr);
-
- /* Set rx threshold, enable DMA */
- /* Set high water mark at 3/4 of full ring */
- port->ip_sscr = (ENTRIES_PER_RING * 3 / 4);
-
- /* uart experiences pauses at high baud rate reducing actual
- * throughput by 10% or so unless we enable high speed polling
- * XXX when this hardware bug is resolved we should revert to
- * normal polling speed
- */
- port->ip_sscr |= SSCR_HIGH_SPD;
-
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
-
- /* Disable and clear all serial related interrupt bits */
- port->ip_card->ic_enable &= ~hooks->intr_clear;
- ioc3_disable(port->ip_is, idd, hooks->intr_clear);
- ioc3_ack(port->ip_is, idd, hooks->intr_clear);
- return 0;
-}
-
-/**
- * enable_intrs - enable interrupts
- * @port: port to enable
- * @mask: mask to use
- */
-static void enable_intrs(struct ioc3_port *port, uint32_t mask)
-{
- if ((port->ip_card->ic_enable & mask) != mask) {
- port->ip_card->ic_enable |= mask;
- ioc3_enable(port->ip_is, port->ip_idd, mask);
- }
-}
-
-/**
- * local_open - local open a port
- * @port: port to open
- */
-static inline int local_open(struct ioc3_port *port)
-{
- int spiniter = 0;
-
- port->ip_flags = INPUT_ENABLE;
-
- /* Pause the DMA interface if necessary */
- if (port->ip_sscr & SSCR_DMA_EN) {
- writel(port->ip_sscr | SSCR_DMA_PAUSE,
- &port->ip_serial_regs->sscr);
- while ((readl(&port->ip_serial_regs->sscr)
- & SSCR_PAUSE_STATE) == 0) {
- spiniter++;
- if (spiniter > MAXITER) {
- NOT_PROGRESS();
- return -1;
- }
- }
- }
-
- /* Reset the input fifo. If the uart received chars while the port
- * was closed and DMA is not enabled, the uart may have a bunch of
- * chars hanging around in its rx fifo which will not be discarded
- * by rclr in the upper layer. We must get rid of them here.
- */
- writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR,
- &port->ip_uart_regs->iu_fcr);
-
- writeb(UART_LCR_WLEN8, &port->ip_uart_regs->iu_lcr);
- /* UART_LCR_STOP == 1 stop */
-
- /* Re-enable DMA, set default threshold to intr whenever there is
- * data available.
- */
- port->ip_sscr &= ~SSCR_RX_THRESHOLD;
- port->ip_sscr |= 1; /* default threshold */
-
- /* Plug in the new sscr. This implicitly clears the DMA_PAUSE
- * flag if it was set above
- */
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- port->ip_tx_lowat = 1;
- return 0;
-}
-
-/**
- * set_rx_timeout - Set rx timeout and threshold values.
- * @port: port to use
- * @timeout: timeout value in ticks
- */
-static inline int set_rx_timeout(struct ioc3_port *port, int timeout)
-{
- int threshold;
-
- port->ip_rx_timeout = timeout;
-
- /* Timeout is in ticks. Let's figure out how many chars we
- * can receive at the current baud rate in that interval
- * and set the rx threshold to that amount. There are 4 chars
- * per ring entry, so we'll divide the number of chars that will
- * arrive in timeout by 4.
- * So .... timeout * baud / 10 / HZ / 4, with HZ = 100.
- */
- threshold = timeout * port->ip_baud / 4000;
- if (threshold == 0)
- threshold = 1; /* otherwise we'll intr all the time! */
-
- if ((unsigned)threshold > (unsigned)SSCR_RX_THRESHOLD)
- return 1;
-
- port->ip_sscr &= ~SSCR_RX_THRESHOLD;
- port->ip_sscr |= threshold;
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
-
- /* Now set the rx timeout to the given value
- * again timeout * SRTR_HZ / HZ
- */
- timeout = timeout * SRTR_HZ / 100;
- if (timeout > SRTR_CNT)
- timeout = SRTR_CNT;
- writel(timeout, &port->ip_serial_regs->srtr);
- return 0;
-}
-
-/**
- * config_port - config the hardware
- * @port: port to config
- * @baud: baud rate for the port
- * @byte_size: data size
- * @stop_bits: number of stop bits
- * @parenb: parity enable ?
- * @parodd: odd parity ?
- */
-static inline int
-config_port(struct ioc3_port *port,
- int baud, int byte_size, int stop_bits, int parenb, int parodd)
-{
- char lcr, sizebits;
- int spiniter = 0;
-
- DPRINT_CONFIG(("%s: line %d baud %d byte_size %d stop %d parenb %d "
- "parodd %d\n",
- __func__, ((struct uart_port *)port->ip_port)->line,
- baud, byte_size, stop_bits, parenb, parodd));
-
- if (set_baud(port, baud))
- return 1;
-
- switch (byte_size) {
- case 5:
- sizebits = UART_LCR_WLEN5;
- break;
- case 6:
- sizebits = UART_LCR_WLEN6;
- break;
- case 7:
- sizebits = UART_LCR_WLEN7;
- break;
- case 8:
- sizebits = UART_LCR_WLEN8;
- break;
- default:
- return 1;
- }
-
- /* Pause the DMA interface if necessary */
- if (port->ip_sscr & SSCR_DMA_EN) {
- writel(port->ip_sscr | SSCR_DMA_PAUSE,
- &port->ip_serial_regs->sscr);
- while ((readl(&port->ip_serial_regs->sscr)
- & SSCR_PAUSE_STATE) == 0) {
- spiniter++;
- if (spiniter > MAXITER)
- return -1;
- }
- }
-
- /* Clear relevant fields in lcr */
- lcr = readb(&port->ip_uart_regs->iu_lcr);
- lcr &= ~(LCR_MASK_BITS_CHAR | UART_LCR_EPAR |
- UART_LCR_PARITY | LCR_MASK_STOP_BITS);
-
- /* Set byte size in lcr */
- lcr |= sizebits;
-
- /* Set parity */
- if (parenb) {
- lcr |= UART_LCR_PARITY;
- if (!parodd)
- lcr |= UART_LCR_EPAR;
- }
-
- /* Set stop bits */
- if (stop_bits)
- lcr |= UART_LCR_STOP /* 2 stop bits */ ;
-
- writeb(lcr, &port->ip_uart_regs->iu_lcr);
-
- /* Re-enable the DMA interface if necessary */
- if (port->ip_sscr & SSCR_DMA_EN) {
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- }
- port->ip_baud = baud;
-
- /* When we get within this number of ring entries of filling the
- * entire ring on tx, place an EXPLICIT intr to generate a lowat
- * notification when output has drained.
- */
- port->ip_tx_lowat = (TX_LOWAT_CHARS(baud) + 3) / 4;
- if (port->ip_tx_lowat == 0)
- port->ip_tx_lowat = 1;
-
- set_rx_timeout(port, 2);
- return 0;
-}
-
-/**
- * do_write - Write bytes to the port. Returns the number of bytes
- * actually written. Called from transmit_chars
- * @port: port to use
- * @buf: the stuff to write
- * @len: how many bytes in 'buf'
- */
-static inline int do_write(struct ioc3_port *port, char *buf, int len)
-{
- int prod_ptr, cons_ptr, total = 0;
- struct ring *outring;
- struct ring_entry *entry;
- struct port_hooks *hooks = port->ip_hooks;
-
- BUG_ON(!(len >= 0));
-
- prod_ptr = port->ip_tx_prod;
- cons_ptr = readl(&port->ip_serial_regs->stcir) & PROD_CONS_MASK;
- outring = port->ip_outring;
-
- /* Maintain a 1-entry red-zone. The ring buffer is full when
- * (cons - prod) % ring_size is 1. Rather than do this subtraction
- * in the body of the loop, I'll do it now.
- */
- cons_ptr = (cons_ptr - (int)sizeof(struct ring_entry)) & PROD_CONS_MASK;
-
- /* Stuff the bytes into the output */
- while ((prod_ptr != cons_ptr) && (len > 0)) {
- int xx;
-
- /* Get 4 bytes (one ring entry) at a time */
- entry = (struct ring_entry *)((caddr_t) outring + prod_ptr);
-
- /* Invalidate all entries */
- entry->ring_allsc = 0;
-
- /* Copy in some bytes */
- for (xx = 0; (xx < 4) && (len > 0); xx++) {
- entry->ring_data[xx] = *buf++;
- entry->ring_sc[xx] = TXCB_VALID;
- len--;
- total++;
- }
-
- /* If we are within some small threshold of filling up the
- * entire ring buffer, we must place an EXPLICIT intr here
- * to generate a lowat interrupt in case we subsequently
- * really do fill up the ring and the caller goes to sleep.
- * No need to place more than one though.
- */
- if (!(port->ip_flags & LOWAT_WRITTEN) &&
- ((cons_ptr - prod_ptr) & PROD_CONS_MASK)
- <= port->ip_tx_lowat * (int)sizeof(struct ring_entry)) {
- port->ip_flags |= LOWAT_WRITTEN;
- entry->ring_sc[0] |= TXCB_INT_WHEN_DONE;
- }
-
- /* Go on to next entry */
- prod_ptr += sizeof(struct ring_entry);
- prod_ptr &= PROD_CONS_MASK;
- }
-
- /* If we sent something, start DMA if necessary */
- if (total > 0 && !(port->ip_sscr & SSCR_DMA_EN)) {
- port->ip_sscr |= SSCR_DMA_EN;
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- }
-
- /* Store the new producer pointer. If tx is disabled, we stuff the
- * data into the ring buffer, but we don't actually start tx.
- */
- if (!uart_tx_stopped(port->ip_port)) {
- writel(prod_ptr, &port->ip_serial_regs->stpir);
-
- /* If we are now transmitting, enable tx_mt interrupt so we
- * can disable DMA if necessary when the tx finishes.
- */
- if (total > 0)
- enable_intrs(port, hooks->intr_tx_mt);
- }
- port->ip_tx_prod = prod_ptr;
-
- return total;
-}
-
-/**
- * disable_intrs - disable interrupts
- * @port: port to enable
- * @mask: mask to use
- */
-static inline void disable_intrs(struct ioc3_port *port, uint32_t mask)
-{
- if (port->ip_card->ic_enable & mask) {
- ioc3_disable(port->ip_is, port->ip_idd, mask);
- port->ip_card->ic_enable &= ~mask;
- }
-}
-
-/**
- * set_notification - Modify event notification
- * @port: port to use
- * @mask: events mask
- * @set_on: set ?
- */
-static int set_notification(struct ioc3_port *port, int mask, int set_on)
-{
- struct port_hooks *hooks = port->ip_hooks;
- uint32_t intrbits, sscrbits;
-
- BUG_ON(!mask);
-
- intrbits = sscrbits = 0;
-
- if (mask & N_DATA_READY)
- intrbits |= (hooks->intr_rx_timer | hooks->intr_rx_high);
- if (mask & N_OUTPUT_LOWAT)
- intrbits |= hooks->intr_tx_explicit;
- if (mask & N_DDCD) {
- intrbits |= hooks->intr_delta_dcd;
- sscrbits |= SSCR_RX_RING_DCD;
- }
- if (mask & N_DCTS)
- intrbits |= hooks->intr_delta_cts;
-
- if (set_on) {
- enable_intrs(port, intrbits);
- port->ip_notify |= mask;
- port->ip_sscr |= sscrbits;
- } else {
- disable_intrs(port, intrbits);
- port->ip_notify &= ~mask;
- port->ip_sscr &= ~sscrbits;
- }
-
- /* We require DMA if either DATA_READY or DDCD notification is
- * currently requested. If neither of these is requested and
- * there is currently no tx in progress, DMA may be disabled.
- */
- if (port->ip_notify & (N_DATA_READY | N_DDCD))
- port->ip_sscr |= SSCR_DMA_EN;
- else if (!(port->ip_card->ic_enable & hooks->intr_tx_mt))
- port->ip_sscr &= ~SSCR_DMA_EN;
-
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- return 0;
-}
-
-/**
- * set_mcr - set the master control reg
- * @the_port: port to use
- * @mask1: mcr mask
- * @mask2: shadow mask
- */
-static inline int set_mcr(struct uart_port *the_port,
- int mask1, int mask2)
-{
- struct ioc3_port *port = get_ioc3_port(the_port);
- uint32_t shadow;
- int spiniter = 0;
- char mcr;
-
- if (!port)
- return -1;
-
- /* Pause the DMA interface if necessary */
- if (port->ip_sscr & SSCR_DMA_EN) {
- writel(port->ip_sscr | SSCR_DMA_PAUSE,
- &port->ip_serial_regs->sscr);
- while ((readl(&port->ip_serial_regs->sscr)
- & SSCR_PAUSE_STATE) == 0) {
- spiniter++;
- if (spiniter > MAXITER)
- return -1;
- }
- }
- shadow = readl(&port->ip_serial_regs->shadow);
- mcr = (shadow & 0xff000000) >> 24;
-
- /* Set new value */
- mcr |= mask1;
- shadow |= mask2;
- writeb(mcr, &port->ip_uart_regs->iu_mcr);
- writel(shadow, &port->ip_serial_regs->shadow);
-
- /* Re-enable the DMA interface if necessary */
- if (port->ip_sscr & SSCR_DMA_EN) {
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- }
- return 0;
-}
-
-/**
- * ioc3_set_proto - set the protocol for the port
- * @port: port to use
- * @proto: protocol to use
- */
-static int ioc3_set_proto(struct ioc3_port *port, int proto)
-{
- struct port_hooks *hooks = port->ip_hooks;
-
- switch (proto) {
- default:
- case PROTO_RS232:
- /* Clear the appropriate GIO pin */
- DPRINT_CONFIG(("%s: rs232\n", __func__));
- writel(0, (&port->ip_idd->vma->gppr[0]
- + hooks->rs422_select_pin));
- break;
-
- case PROTO_RS422:
- /* Set the appropriate GIO pin */
- DPRINT_CONFIG(("%s: rs422\n", __func__));
- writel(1, (&port->ip_idd->vma->gppr[0]
- + hooks->rs422_select_pin));
- break;
- }
- return 0;
-}
-
-/**
- * transmit_chars - upper level write, called with the_port->lock
- * @the_port: port to write
- */
-static void transmit_chars(struct uart_port *the_port)
-{
- int xmit_count, tail, head;
- int result;
- char *start;
- struct tty_struct *tty;
- struct ioc3_port *port = get_ioc3_port(the_port);
- struct uart_state *state;
-
- if (!the_port)
- return;
- if (!port)
- return;
-
- state = the_port->state;
- tty = state->port.tty;
-
- if (uart_circ_empty(&state->xmit) || uart_tx_stopped(the_port)) {
- /* Nothing to do or hw stopped */
- set_notification(port, N_ALL_OUTPUT, 0);
- return;
- }
-
- head = state->xmit.head;
- tail = state->xmit.tail;
- start = (char *)&state->xmit.buf[tail];
-
- /* write out all the data or until the end of the buffer */
- xmit_count = (head < tail) ? (UART_XMIT_SIZE - tail) : (head - tail);
- if (xmit_count > 0) {
- result = do_write(port, start, xmit_count);
- if (result > 0) {
- /* booking */
- xmit_count -= result;
- the_port->icount.tx += result;
- /* advance the pointers */
- tail += result;
- tail &= UART_XMIT_SIZE - 1;
- state->xmit.tail = tail;
- start = (char *)&state->xmit.buf[tail];
- }
- }
- if (uart_circ_chars_pending(&state->xmit) < WAKEUP_CHARS)
- uart_write_wakeup(the_port);
-
- if (uart_circ_empty(&state->xmit)) {
- set_notification(port, N_OUTPUT_LOWAT, 0);
- } else {
- set_notification(port, N_OUTPUT_LOWAT, 1);
- }
-}
-
-/**
- * ioc3_change_speed - change the speed of the port
- * @the_port: port to change
- * @new_termios: new termios settings
- * @old_termios: old termios settings
- */
-static void
-ioc3_change_speed(struct uart_port *the_port,
- struct ktermios *new_termios, struct ktermios *old_termios)
-{
- struct ioc3_port *port = get_ioc3_port(the_port);
- unsigned int cflag, iflag;
- int baud;
- int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8;
- struct uart_state *state = the_port->state;
-
- cflag = new_termios->c_cflag;
- iflag = new_termios->c_iflag;
-
- switch (cflag & CSIZE) {
- case CS5:
- new_data = 5;
- break;
- case CS6:
- new_data = 6;
- break;
- case CS7:
- new_data = 7;
- break;
- case CS8:
- new_data = 8;
- break;
- default:
- /* cuz we always need a default ... */
- new_data = 5;
- break;
- }
- if (cflag & CSTOPB) {
- new_stop = 1;
- }
- if (cflag & PARENB) {
- new_parity_enable = 1;
- if (cflag & PARODD)
- new_parity = 1;
- }
- baud = uart_get_baud_rate(the_port, new_termios, old_termios,
- MIN_BAUD_SUPPORTED, MAX_BAUD_SUPPORTED);
- DPRINT_CONFIG(("%s: returned baud %d for line %d\n", __func__, baud,
- the_port->line));
-
- if (!the_port->fifosize)
- the_port->fifosize = FIFO_SIZE;
- uart_update_timeout(the_port, cflag, baud);
-
- the_port->ignore_status_mask = N_ALL_INPUT;
-
- state->port.low_latency = 1;
-
- if (iflag & IGNPAR)
- the_port->ignore_status_mask &= ~(N_PARITY_ERROR
- | N_FRAMING_ERROR);
- if (iflag & IGNBRK) {
- the_port->ignore_status_mask &= ~N_BREAK;
- if (iflag & IGNPAR)
- the_port->ignore_status_mask &= ~N_OVERRUN_ERROR;
- }
- if (!(cflag & CREAD)) {
- /* ignore everything */
- the_port->ignore_status_mask &= ~N_DATA_READY;
- }
-
- if (cflag & CRTSCTS) {
- /* enable hardware flow control */
- port->ip_sscr |= SSCR_HFC_EN;
- }
- else {
- /* disable hardware flow control */
- port->ip_sscr &= ~SSCR_HFC_EN;
- }
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
-
- /* Set the configuration and proper notification call */
- DPRINT_CONFIG(("%s : port 0x%p line %d cflag 0%o "
- "config_port(baud %d data %d stop %d penable %d "
- " parity %d), notification 0x%x\n",
- __func__, (void *)port, the_port->line, cflag, baud,
- new_data, new_stop, new_parity_enable, new_parity,
- the_port->ignore_status_mask));
-
- if ((config_port(port, baud, /* baud */
- new_data, /* byte size */
- new_stop, /* stop bits */
- new_parity_enable, /* set parity */
- new_parity)) >= 0) { /* parity 1==odd */
- set_notification(port, the_port->ignore_status_mask, 1);
- }
-}
-
-/**
- * ic3_startup_local - Start up the serial port - returns >= 0 if no errors
- * @the_port: Port to operate on
- */
-static inline int ic3_startup_local(struct uart_port *the_port)
-{
- struct ioc3_port *port;
-
- if (!the_port) {
- NOT_PROGRESS();
- return -1;
- }
-
- port = get_ioc3_port(the_port);
- if (!port) {
- NOT_PROGRESS();
- return -1;
- }
-
- local_open(port);
-
- /* set the protocol */
- ioc3_set_proto(port, IS_RS232(the_port->line) ? PROTO_RS232 :
- PROTO_RS422);
- return 0;
-}
-
-/*
- * ioc3_cb_output_lowat - called when the output low water mark is hit
- * @port: port to output
- */
-static void ioc3_cb_output_lowat(struct ioc3_port *port)
-{
- unsigned long pflags;
-
- /* the_port->lock is set on the call here */
- if (port->ip_port) {
- spin_lock_irqsave(&port->ip_port->lock, pflags);
- transmit_chars(port->ip_port);
- spin_unlock_irqrestore(&port->ip_port->lock, pflags);
- }
-}
-
-/*
- * ioc3_cb_post_ncs - called for some basic errors
- * @port: port to use
- * @ncs: event
- */
-static void ioc3_cb_post_ncs(struct uart_port *the_port, int ncs)
-{
- struct uart_icount *icount;
-
- icount = &the_port->icount;
-
- if (ncs & NCS_BREAK)
- icount->brk++;
- if (ncs & NCS_FRAMING)
- icount->frame++;
- if (ncs & NCS_OVERRUN)
- icount->overrun++;
- if (ncs & NCS_PARITY)
- icount->parity++;
-}
-
-/**
- * do_read - Read in bytes from the port. Return the number of bytes
- * actually read.
- * @the_port: port to use
- * @buf: place to put the stuff we read
- * @len: how big 'buf' is
- */
-
-static inline int do_read(struct uart_port *the_port, char *buf, int len)
-{
- int prod_ptr, cons_ptr, total;
- struct ioc3_port *port = get_ioc3_port(the_port);
- struct ring *inring;
- struct ring_entry *entry;
- struct port_hooks *hooks;
- int byte_num;
- char *sc;
- int loop_counter;
-
- BUG_ON(!(len >= 0));
- BUG_ON(!port);
- hooks = port->ip_hooks;
-
- /* There is a nasty timing issue in the IOC3. When the rx_timer
- * expires or the rx_high condition arises, we take an interrupt.
- * At some point while servicing the interrupt, we read bytes from
- * the ring buffer and re-arm the rx_timer. However the rx_timer is
- * not started until the first byte is received *after* it is armed,
- * and any bytes pending in the rx construction buffers are not drained
- * to memory until either there are 4 bytes available or the rx_timer
- * expires. This leads to a potential situation where data is left
- * in the construction buffers forever - 1 to 3 bytes were received
- * after the interrupt was generated but before the rx_timer was
- * re-armed. At that point as long as no subsequent bytes are received
- * the timer will never be started and the bytes will remain in the
- * construction buffer forever. The solution is to execute a DRAIN
- * command after rearming the timer. This way any bytes received before
- * the DRAIN will be drained to memory, and any bytes received after
- * the DRAIN will start the TIMER and be drained when it expires.
- * Luckily, this only needs to be done when the DMA buffer is empty
- * since there is no requirement that this function return all
- * available data as long as it returns some.
- */
- /* Re-arm the timer */
-
- writel(port->ip_rx_cons | SRCIR_ARM, &port->ip_serial_regs->srcir);
-
- prod_ptr = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
- cons_ptr = port->ip_rx_cons;
-
- if (prod_ptr == cons_ptr) {
- int reset_dma = 0;
-
- /* Input buffer appears empty, do a flush. */
-
- /* DMA must be enabled for this to work. */
- if (!(port->ip_sscr & SSCR_DMA_EN)) {
- port->ip_sscr |= SSCR_DMA_EN;
- reset_dma = 1;
- }
-
- /* Potential race condition: we must reload the srpir after
- * issuing the drain command, otherwise we could think the rx
- * buffer is empty, then take a very long interrupt, and when
- * we come back it's full and we wait forever for the drain to
- * complete.
- */
- writel(port->ip_sscr | SSCR_RX_DRAIN,
- &port->ip_serial_regs->sscr);
- prod_ptr = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
-
- /* We must not wait for the DRAIN to complete unless there are
- * at least 8 bytes (2 ring entries) available to receive the
- * data otherwise the DRAIN will never complete and we'll
- * deadlock here.
- * In fact, to make things easier, I'll just ignore the flush if
- * there is any data at all now available.
- */
- if (prod_ptr == cons_ptr) {
- loop_counter = 0;
- while (readl(&port->ip_serial_regs->sscr) &
- SSCR_RX_DRAIN) {
- loop_counter++;
- if (loop_counter > MAXITER)
- return -1;
- }
-
- /* SIGH. We have to reload the prod_ptr *again* since
- * the drain may have caused it to change
- */
- prod_ptr = readl(&port->ip_serial_regs->srpir)
- & PROD_CONS_MASK;
- }
- if (reset_dma) {
- port->ip_sscr &= ~SSCR_DMA_EN;
- writel(port->ip_sscr, &port->ip_serial_regs->sscr);
- }
- }
- inring = port->ip_inring;
- port->ip_flags &= ~READ_ABORTED;
-
- total = 0;
- loop_counter = 0xfffff; /* to avoid hangs */
-
- /* Grab bytes from the hardware */
- while ((prod_ptr != cons_ptr) && (len > 0)) {
- entry = (struct ring_entry *)((caddr_t) inring + cons_ptr);
-
- if (loop_counter-- <= 0) {
- printk(KERN_WARNING "IOC3 serial: "
- "possible hang condition/"
- "port stuck on read (line %d).\n",
- the_port->line);
- break;
- }
-
- /* According to the producer pointer, this ring entry
- * must contain some data. But if the PIO happened faster
- * than the DMA, the data may not be available yet, so let's
- * wait until it arrives.
- */
- if ((entry->ring_allsc & RING_ANY_VALID) == 0) {
- /* Indicate the read is aborted so we don't disable
- * the interrupt thinking that the consumer is
- * congested.
- */
- port->ip_flags |= READ_ABORTED;
- len = 0;
- break;
- }
-
- /* Load the bytes/status out of the ring entry */
- for (byte_num = 0; byte_num < 4 && len > 0; byte_num++) {
- sc = &(entry->ring_sc[byte_num]);
-
- /* Check for change in modem state or overrun */
- if ((*sc & RXSB_MODEM_VALID)
- && (port->ip_notify & N_DDCD)) {
- /* Notify upper layer if DCD dropped */
- if ((port->ip_flags & DCD_ON)
- && !(*sc & RXSB_DCD)) {
- /* If we have already copied some data,
- * return it. We'll pick up the carrier
- * drop on the next pass. That way we
- * don't throw away the data that has
- * already been copied back to
- * the caller's buffer.
- */
- if (total > 0) {
- len = 0;
- break;
- }
- port->ip_flags &= ~DCD_ON;
-
- /* Turn off this notification so the
- * carrier drop protocol won't see it
- * again when it does a read.
- */
- *sc &= ~RXSB_MODEM_VALID;
-
- /* To keep things consistent, we need
- * to update the consumer pointer so
- * the next reader won't come in and
- * try to read the same ring entries
- * again. This must be done here before
- * the dcd change.
- */
-
- if ((entry->ring_allsc & RING_ANY_VALID)
- == 0) {
- cons_ptr += (int)sizeof
- (struct ring_entry);
- cons_ptr &= PROD_CONS_MASK;
- }
- writel(cons_ptr,
- &port->ip_serial_regs->srcir);
- port->ip_rx_cons = cons_ptr;
-
- /* Notify upper layer of carrier drop */
- if ((port->ip_notify & N_DDCD)
- && port->ip_port) {
- uart_handle_dcd_change
- (port->ip_port, 0);
- wake_up_interruptible
- (&the_port->state->
- port.delta_msr_wait);
- }
-
- /* If we had any data to return, we
- * would have returned it above.
- */
- return 0;
- }
- }
- if (*sc & RXSB_MODEM_VALID) {
- /* Notify that an input overrun occurred */
- if ((*sc & RXSB_OVERRUN)
- && (port->ip_notify & N_OVERRUN_ERROR)) {
- ioc3_cb_post_ncs(the_port, NCS_OVERRUN);
- }
- /* Don't look at this byte again */
- *sc &= ~RXSB_MODEM_VALID;
- }
-
- /* Check for valid data or RX errors */
- if ((*sc & RXSB_DATA_VALID) &&
- ((*sc & (RXSB_PAR_ERR
- | RXSB_FRAME_ERR | RXSB_BREAK))
- && (port->ip_notify & (N_PARITY_ERROR
- | N_FRAMING_ERROR
- | N_BREAK)))) {
- /* There is an error condition on the next byte.
- * If we have already transferred some bytes,
- * we'll stop here. Otherwise if this is the
- * first byte to be read, we'll just transfer
- * it alone after notifying the
- * upper layer of its status.
- */
- if (total > 0) {
- len = 0;
- break;
- } else {
- if ((*sc & RXSB_PAR_ERR) &&
- (port->
- ip_notify & N_PARITY_ERROR)) {
- ioc3_cb_post_ncs(the_port,
- NCS_PARITY);
- }
- if ((*sc & RXSB_FRAME_ERR) &&
- (port->
- ip_notify & N_FRAMING_ERROR)) {
- ioc3_cb_post_ncs(the_port,
- NCS_FRAMING);
- }
- if ((*sc & RXSB_BREAK)
- && (port->ip_notify & N_BREAK)) {
- ioc3_cb_post_ncs
- (the_port, NCS_BREAK);
- }
- len = 1;
- }
- }
- if (*sc & RXSB_DATA_VALID) {
- *sc &= ~RXSB_DATA_VALID;
- *buf = entry->ring_data[byte_num];
- buf++;
- len--;
- total++;
- }
- }
-
- /* If we used up this entry entirely, go on to the next one,
- * otherwise we must have run out of buffer space, so
- * leave the consumer pointer here for the next read in case
- * there are still unread bytes in this entry.
- */
- if ((entry->ring_allsc & RING_ANY_VALID) == 0) {
- cons_ptr += (int)sizeof(struct ring_entry);
- cons_ptr &= PROD_CONS_MASK;
- }
- }
-
- /* Update consumer pointer and re-arm rx timer interrupt */
- writel(cons_ptr, &port->ip_serial_regs->srcir);
- port->ip_rx_cons = cons_ptr;
-
- /* If we have now dipped below the rx high water mark and we have
- * rx_high interrupt turned off, we can now turn it back on again.
- */
- if ((port->ip_flags & INPUT_HIGH) && (((prod_ptr - cons_ptr)
- & PROD_CONS_MASK) <
- ((port->
- ip_sscr &
- SSCR_RX_THRESHOLD)
- << PROD_CONS_PTR_OFF))) {
- port->ip_flags &= ~INPUT_HIGH;
- enable_intrs(port, hooks->intr_rx_high);
- }
- return total;
-}
-
-/**
- * receive_chars - upper level read.
- * @the_port: port to read from
- */
-static int receive_chars(struct uart_port *the_port)
-{
- unsigned char ch[MAX_CHARS];
- int read_count = 0, read_room, flip = 0;
- struct uart_state *state = the_port->state;
- struct ioc3_port *port = get_ioc3_port(the_port);
- unsigned long pflags;
-
- /* Make sure all the pointers are "good" ones */
- if (!state)
- return 0;
-
- if (!(port->ip_flags & INPUT_ENABLE))
- return 0;
-
- spin_lock_irqsave(&the_port->lock, pflags);
-
- read_count = do_read(the_port, ch, MAX_CHARS);
- if (read_count > 0) {
- flip = 1;
- read_room = tty_insert_flip_string(&state->port, ch,
- read_count);
- the_port->icount.rx += read_count;
- }
- spin_unlock_irqrestore(&the_port->lock, pflags);
-
- if (flip)
- tty_flip_buffer_push(&state->port);
-
- return read_count;
-}
-
-/**
- * ioc3uart_intr_one - lowest level (per port) interrupt handler.
- * @is : submodule
- * @idd: driver data
- * @pending: interrupts to handle
- */
-
-static inline int
-ioc3uart_intr_one(struct ioc3_submodule *is,
- struct ioc3_driver_data *idd,
- unsigned int pending)
-{
- int port_num = GET_PORT_FROM_SIO_IR(pending);
- struct port_hooks *hooks;
- unsigned int rx_high_rd_aborted = 0;
- unsigned long flags;
- struct uart_port *the_port;
- struct ioc3_port *port;
- int loop_counter;
- struct ioc3_card *card_ptr;
- unsigned int sio_ir;
-
- card_ptr = idd->data[is->id];
- port = card_ptr->ic_port[port_num].icp_port;
- hooks = port->ip_hooks;
-
- /* Possible race condition here: The tx_mt interrupt bit may be
- * cleared without the intervention of the interrupt handler,
- * e.g. by a write. If the top level interrupt handler reads a
- * tx_mt, then some other processor does a write, starting up
- * output, then we come in here, see the tx_mt and stop DMA, the
- * output started by the other processor will hang. Thus we can
- * only rely on tx_mt being legitimate if it is read while the
- * port lock is held. Therefore this bit must be ignored in the
- * passed in interrupt mask which was read by the top level
- * interrupt handler since the port lock was not held at the time
- * it was read. We can only rely on this bit being accurate if it
- * is read while the port lock is held. So we'll clear it for now,
- * and reload it later once we have the port lock.
- */
-
- sio_ir = pending & ~(hooks->intr_tx_mt);
- spin_lock_irqsave(&port->ip_lock, flags);
-
- loop_counter = MAXITER; /* to avoid hangs */
-
- do {
- uint32_t shadow;
-
- if (loop_counter-- <= 0) {
- printk(KERN_WARNING "IOC3 serial: "
- "possible hang condition/"
- "port stuck on interrupt (line %d).\n",
- ((struct uart_port *)port->ip_port)->line);
- break;
- }
- /* Handle a DCD change */
- if (sio_ir & hooks->intr_delta_dcd) {
- ioc3_ack(is, idd, hooks->intr_delta_dcd);
- shadow = readl(&port->ip_serial_regs->shadow);
-
- if ((port->ip_notify & N_DDCD)
- && (shadow & SHADOW_DCD)
- && (port->ip_port)) {
- the_port = port->ip_port;
- uart_handle_dcd_change(the_port,
- shadow & SHADOW_DCD);
- wake_up_interruptible
- (&the_port->state->port.delta_msr_wait);
- } else if ((port->ip_notify & N_DDCD)
- && !(shadow & SHADOW_DCD)) {
- /* Flag delta DCD/no DCD */
- uart_handle_dcd_change(port->ip_port,
- shadow & SHADOW_DCD);
- port->ip_flags |= DCD_ON;
- }
- }
-
- /* Handle a CTS change */
- if (sio_ir & hooks->intr_delta_cts) {
- ioc3_ack(is, idd, hooks->intr_delta_cts);
- shadow = readl(&port->ip_serial_regs->shadow);
-
- if ((port->ip_notify & N_DCTS) && (port->ip_port)) {
- the_port = port->ip_port;
- uart_handle_cts_change(the_port, shadow
- & SHADOW_CTS);
- wake_up_interruptible
- (&the_port->state->port.delta_msr_wait);
- }
- }
-
- /* rx timeout interrupt. Must be some data available. Put this
- * before the check for rx_high since servicing this condition
- * may cause that condition to clear.
- */
- if (sio_ir & hooks->intr_rx_timer) {
- ioc3_ack(is, idd, hooks->intr_rx_timer);
- if ((port->ip_notify & N_DATA_READY)
- && (port->ip_port)) {
- receive_chars(port->ip_port);
- }
- }
-
- /* rx high interrupt. Must be after rx_timer. */
- else if (sio_ir & hooks->intr_rx_high) {
- /* Data available, notify upper layer */
- if ((port->ip_notify & N_DATA_READY) && port->ip_port) {
- receive_chars(port->ip_port);
- }
-
- /* We can't ACK this interrupt. If receive_chars didn't
- * cause the condition to clear, we'll have to disable
- * the interrupt until the data is drained.
- * If the read was aborted, don't disable the interrupt
- * as this may cause us to hang indefinitely. An
- * aborted read generally means that this interrupt
- * hasn't been delivered to the cpu yet anyway, even
- * though we see it as asserted when we read the sio_ir.
- */
- if ((sio_ir = PENDING(card_ptr, idd))
- & hooks->intr_rx_high) {
- if (port->ip_flags & READ_ABORTED) {
- rx_high_rd_aborted++;
- }
- else {
- card_ptr->ic_enable &= ~hooks->intr_rx_high;
- port->ip_flags |= INPUT_HIGH;
- }
- }
- }
-
- /* We got a low water interrupt: notify upper layer to
- * send more data. Must come before tx_mt since servicing
- * this condition may cause that condition to clear.
- */
- if (sio_ir & hooks->intr_tx_explicit) {
- port->ip_flags &= ~LOWAT_WRITTEN;
- ioc3_ack(is, idd, hooks->intr_tx_explicit);
- if (port->ip_notify & N_OUTPUT_LOWAT)
- ioc3_cb_output_lowat(port);
- }
-
- /* Handle tx_mt. Must come after tx_explicit. */
- else if (sio_ir & hooks->intr_tx_mt) {
- /* If we are expecting a lowat notification
- * and we get to this point it probably means that for
- * some reason the tx_explicit didn't work as expected
- * (that can legitimately happen if the output buffer is
- * filled up in just the right way).
- * So send the notification now.
- */
- if (port->ip_notify & N_OUTPUT_LOWAT) {
- ioc3_cb_output_lowat(port);
-
- /* We need to reload the sio_ir since the lowat
- * call may have caused another write to occur,
- * clearing the tx_mt condition.
- */
- sio_ir = PENDING(card_ptr, idd);
- }
-
- /* If the tx_mt condition still persists even after the
- * lowat call, we've got some work to do.
- */
- if (sio_ir & hooks->intr_tx_mt) {
- /* If we are not currently expecting DMA input,
- * and the transmitter has just gone idle,
- * there is no longer any reason for DMA, so
- * disable it.
- */
- if (!(port->ip_notify
- & (N_DATA_READY | N_DDCD))) {
- BUG_ON(!(port->ip_sscr
- & SSCR_DMA_EN));
- port->ip_sscr &= ~SSCR_DMA_EN;
- writel(port->ip_sscr,
- &port->ip_serial_regs->sscr);
- }
- /* Prevent infinite tx_mt interrupt */
- card_ptr->ic_enable &= ~hooks->intr_tx_mt;
- }
- }
- sio_ir = PENDING(card_ptr, idd);
-
- /* if the read was aborted and only hooks->intr_rx_high,
- * clear hooks->intr_rx_high, so we do not loop forever.
- */
-
- if (rx_high_rd_aborted && (sio_ir == hooks->intr_rx_high)) {
- sio_ir &= ~hooks->intr_rx_high;
- }
- } while (sio_ir & hooks->intr_all);
-
- spin_unlock_irqrestore(&port->ip_lock, flags);
- ioc3_enable(is, idd, card_ptr->ic_enable);
- return 0;
-}
-
-/**
- * ioc3uart_intr - field all serial interrupts
- * @is : submodule
- * @idd: driver data
- * @pending: interrupts to handle
- *
- */
-
-static int ioc3uart_intr(struct ioc3_submodule *is,
- struct ioc3_driver_data *idd,
- unsigned int pending)
-{
- int ret = 0;
-
- /*
- * The upper level interrupt handler sends interrupts for both ports
- * here. So we need to call for each port with its interrupts.
- */
-
- if (pending & SIO_IR_SA)
- ret |= ioc3uart_intr_one(is, idd, pending & SIO_IR_SA);
- if (pending & SIO_IR_SB)
- ret |= ioc3uart_intr_one(is, idd, pending & SIO_IR_SB);
-
- return ret;
-}
-
-/**
- * ic3_type
- * @port: Port to operate with (we ignore since we only have one port)
- *
- */
-static const char *ic3_type(struct uart_port *the_port)
-{
- if (IS_RS232(the_port->line))
- return "SGI IOC3 Serial [rs232]";
- else
- return "SGI IOC3 Serial [rs422]";
-}
-
-/**
- * ic3_tx_empty - Is the transmitter empty?
- * @port: Port to operate on
- *
- */
-static unsigned int ic3_tx_empty(struct uart_port *the_port)
-{
- unsigned int ret = 0;
- struct ioc3_port *port = get_ioc3_port(the_port);
-
- if (readl(&port->ip_serial_regs->shadow) & SHADOW_TEMT)
- ret = TIOCSER_TEMT;
- return ret;
-}
-
-/**
- * ic3_stop_tx - stop the transmitter
- * @port: Port to operate on
- *
- */
-static void ic3_stop_tx(struct uart_port *the_port)
-{
- struct ioc3_port *port = get_ioc3_port(the_port);
-
- if (port)
- set_notification(port, N_OUTPUT_LOWAT, 0);
-}
-
-/**
- * ic3_stop_rx - stop the receiver
- * @port: Port to operate on
- *
- */
-static void ic3_stop_rx(struct uart_port *the_port)
-{
- struct ioc3_port *port = get_ioc3_port(the_port);
-
- if (port)
- port->ip_flags &= ~INPUT_ENABLE;
-}
-
-/**
- * null_void_function
- * @port: Port to operate on
- *
- */
-static void null_void_function(struct uart_port *the_port)
-{
-}
-
-/**
- * ic3_shutdown - shut down the port - free irq and disable
- * @port: port to shut down
- *
- */
-static void ic3_shutdown(struct uart_port *the_port)
-{
- unsigned long port_flags;
- struct ioc3_port *port;
- struct uart_state *state;
-
- port = get_ioc3_port(the_port);
- if (!port)
- return;
-
- state = the_port->state;
- wake_up_interruptible(&state->port.delta_msr_wait);
-
- spin_lock_irqsave(&the_port->lock, port_flags);
- set_notification(port, N_ALL, 0);
- spin_unlock_irqrestore(&the_port->lock, port_flags);
-}
-
-/**
- * ic3_set_mctrl - set control lines (dtr, rts, etc)
- * @port: Port to operate on
- * @mctrl: Lines to set/unset
- *
- */
-static void ic3_set_mctrl(struct uart_port *the_port, unsigned int mctrl)
-{
- unsigned char mcr = 0;
-
- if (mctrl & TIOCM_RTS)
- mcr |= UART_MCR_RTS;
- if (mctrl & TIOCM_DTR)
- mcr |= UART_MCR_DTR;
- if (mctrl & TIOCM_OUT1)
- mcr |= UART_MCR_OUT1;
- if (mctrl & TIOCM_OUT2)
- mcr |= UART_MCR_OUT2;
- if (mctrl & TIOCM_LOOP)
- mcr |= UART_MCR_LOOP;
-
- set_mcr(the_port, mcr, SHADOW_DTR);
-}
-
-/**
- * ic3_get_mctrl - get control line info
- * @port: port to operate on
- *
- */
-static unsigned int ic3_get_mctrl(struct uart_port *the_port)
-{
- struct ioc3_port *port = get_ioc3_port(the_port);
- uint32_t shadow;
- unsigned int ret = 0;
-
- if (!port)
- return 0;
-
- shadow = readl(&port->ip_serial_regs->shadow);
- if (shadow & SHADOW_DCD)
- ret |= TIOCM_CD;
- if (shadow & SHADOW_DR)
- ret |= TIOCM_DSR;
- if (shadow & SHADOW_CTS)
- ret |= TIOCM_CTS;
- return ret;
-}
-
-/**
- * ic3_start_tx - Start transmitter. Called with the_port->lock
- * @port: Port to operate on
- *
- */
-static void ic3_start_tx(struct uart_port *the_port)
-{
- struct ioc3_port *port = get_ioc3_port(the_port);
-
- if (port) {
- set_notification(port, N_OUTPUT_LOWAT, 1);
- enable_intrs(port, port->ip_hooks->intr_tx_mt);
- }
-}
-
-/**
- * ic3_break_ctl - handle breaks
- * @port: Port to operate on
- * @break_state: Break state
- *
- */
-static void ic3_break_ctl(struct uart_port *the_port, int break_state)
-{
-}
-
-/**
- * ic3_startup - Start up the serial port - always return 0 (We're always on)
- * @port: Port to operate on
- *
- */
-static int ic3_startup(struct uart_port *the_port)
-{
- int retval;
- struct ioc3_port *port;
- struct ioc3_card *card_ptr;
- unsigned long port_flags;
-
- if (!the_port) {
- NOT_PROGRESS();
- return -ENODEV;
- }
- port = get_ioc3_port(the_port);
- if (!port) {
- NOT_PROGRESS();
- return -ENODEV;
- }
- card_ptr = port->ip_card;
- port->ip_port = the_port;
-
- if (!card_ptr) {
- NOT_PROGRESS();
- return -ENODEV;
- }
-
- /* Start up the serial port */
- spin_lock_irqsave(&the_port->lock, port_flags);
- retval = ic3_startup_local(the_port);
- spin_unlock_irqrestore(&the_port->lock, port_flags);
- return retval;
-}
-
-/**
- * ic3_set_termios - set termios stuff
- * @port: port to operate on
- * @termios: New settings
- * @termios: Old
- *
- */
-static void
-ic3_set_termios(struct uart_port *the_port,
- struct ktermios *termios, struct ktermios *old_termios)
-{
- unsigned long port_flags;
-
- spin_lock_irqsave(&the_port->lock, port_flags);
- ioc3_change_speed(the_port, termios, old_termios);
- spin_unlock_irqrestore(&the_port->lock, port_flags);
-}
-
-/**
- * ic3_request_port - allocate resources for port - no op....
- * @port: port to operate on
- *
- */
-static int ic3_request_port(struct uart_port *port)
-{
- return 0;
-}
-
-/* Associate the uart functions above - given to serial core */
-static const struct uart_ops ioc3_ops = {
- .tx_empty = ic3_tx_empty,
- .set_mctrl = ic3_set_mctrl,
- .get_mctrl = ic3_get_mctrl,
- .stop_tx = ic3_stop_tx,
- .start_tx = ic3_start_tx,
- .stop_rx = ic3_stop_rx,
- .break_ctl = ic3_break_ctl,
- .startup = ic3_startup,
- .shutdown = ic3_shutdown,
- .set_termios = ic3_set_termios,
- .type = ic3_type,
- .release_port = null_void_function,
- .request_port = ic3_request_port,
-};
-
-/*
- * Boot-time initialization code
- */
-
-static struct uart_driver ioc3_uart = {
- .owner = THIS_MODULE,
- .driver_name = "ioc3_serial",
- .dev_name = DEVICE_NAME,
- .major = DEVICE_MAJOR,
- .minor = DEVICE_MINOR,
- .nr = MAX_LOGICAL_PORTS
-};
-
-/**
- * ioc3_serial_core_attach - register with serial core
- * This is done during pci probing
- * @is: submodule struct for this
- * @idd: handle for this card
- */
-static inline int ioc3_serial_core_attach( struct ioc3_submodule *is,
- struct ioc3_driver_data *idd)
-{
- struct ioc3_port *port;
- struct uart_port *the_port;
- struct ioc3_card *card_ptr = idd->data[is->id];
- int ii, phys_port;
- struct pci_dev *pdev = idd->pdev;
-
- DPRINT_CONFIG(("%s: attach pdev 0x%p - card_ptr 0x%p\n",
- __func__, pdev, (void *)card_ptr));
-
- if (!card_ptr)
- return -ENODEV;
-
- /* once around for each logical port on this card */
- for (ii = 0; ii < LOGICAL_PORTS_PER_CARD; ii++) {
- phys_port = GET_PHYSICAL_PORT(ii);
- the_port = &card_ptr->ic_port[phys_port].
- icp_uart_port[GET_LOGICAL_PORT(ii)];
- port = card_ptr->ic_port[phys_port].icp_port;
- port->ip_port = the_port;
-
- DPRINT_CONFIG(("%s: attach the_port 0x%p / port 0x%p [%d/%d]\n",
- __func__, (void *)the_port, (void *)port,
- phys_port, ii));
-
- /* membase, iobase and mapbase just need to be non-0 */
- the_port->membase = (unsigned char __iomem *)1;
- the_port->iobase = (pdev->bus->number << 16) | ii;
- the_port->line = (Num_of_ioc3_cards << 2) | ii;
- the_port->mapbase = 1;
- the_port->type = PORT_16550A;
- the_port->fifosize = FIFO_SIZE;
- the_port->ops = &ioc3_ops;
- the_port->irq = idd->irq_io;
- the_port->dev = &pdev->dev;
-
- if (uart_add_one_port(&ioc3_uart, the_port) < 0) {
- printk(KERN_WARNING
- "%s: unable to add port %d bus %d\n",
- __func__, the_port->line, pdev->bus->number);
- } else {
- DPRINT_CONFIG(("IOC3 serial port %d irq %d bus %d\n",
- the_port->line, the_port->irq, pdev->bus->number));
- }
-
- /* all ports are rs232 for now */
- if (IS_PHYSICAL_PORT(ii))
- ioc3_set_proto(port, PROTO_RS232);
- }
- return 0;
-}
-
-/**
- * ioc3uart_remove - register detach function
- * @is: submodule struct for this submodule
- * @idd: ioc3 driver data for this submodule
- */
-
-static int ioc3uart_remove(struct ioc3_submodule *is,
- struct ioc3_driver_data *idd)
-{
- struct ioc3_card *card_ptr = idd->data[is->id];
- struct uart_port *the_port;
- struct ioc3_port *port;
- int ii;
-
- if (card_ptr) {
- for (ii = 0; ii < LOGICAL_PORTS_PER_CARD; ii++) {
- the_port = &card_ptr->ic_port[GET_PHYSICAL_PORT(ii)].
- icp_uart_port[GET_LOGICAL_PORT(ii)];
- if (the_port)
- uart_remove_one_port(&ioc3_uart, the_port);
- port = card_ptr->ic_port[GET_PHYSICAL_PORT(ii)].icp_port;
- if (port && IS_PHYSICAL_PORT(ii)
- && (GET_PHYSICAL_PORT(ii) == 0)) {
- pci_free_consistent(port->ip_idd->pdev,
- TOTAL_RING_BUF_SIZE,
- (void *)port->ip_cpu_ringbuf,
- port->ip_dma_ringbuf);
- kfree(port);
- card_ptr->ic_port[GET_PHYSICAL_PORT(ii)].
- icp_port = NULL;
- }
- }
- kfree(card_ptr);
- idd->data[is->id] = NULL;
- }
- return 0;
-}
-
-/**
- * ioc3uart_probe - card probe function called from shim driver
- * @is: submodule struct for this submodule
- * @idd: ioc3 driver data for this card
- */
-
-static int
-ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd)
-{
- struct pci_dev *pdev = idd->pdev;
- struct ioc3_card *card_ptr;
- int ret = 0;
- struct ioc3_port *port;
- struct ioc3_port *ports[PORTS_PER_CARD];
- int phys_port;
- int cnt;
-
- DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __func__, is, idd));
-
- card_ptr = kzalloc(sizeof(struct ioc3_card), GFP_KERNEL);
- if (!card_ptr) {
- printk(KERN_WARNING "ioc3_attach_one"
- ": unable to get memory for the IOC3\n");
- return -ENOMEM;
- }
- idd->data[is->id] = card_ptr;
- Submodule_slot = is->id;
-
- writel(((UARTA_BASE >> 3) << SIO_CR_SER_A_BASE_SHIFT) |
- ((UARTB_BASE >> 3) << SIO_CR_SER_B_BASE_SHIFT) |
- (0xf << SIO_CR_CMD_PULSE_SHIFT), &idd->vma->sio_cr);
-
- pci_write_config_dword(pdev, PCI_LAT, 0xff00);
-
- /* Enable serial port mode select generic PIO pins as outputs */
- ioc3_gpcr_set(idd, GPCR_UARTA_MODESEL | GPCR_UARTB_MODESEL);
-
- /* Create port structures for each port */
- for (phys_port = 0; phys_port < PORTS_PER_CARD; phys_port++) {
- port = kzalloc(sizeof(struct ioc3_port), GFP_KERNEL);
- if (!port) {
- printk(KERN_WARNING
- "IOC3 serial memory not available for port\n");
- ret = -ENOMEM;
- goto out4;
- }
- spin_lock_init(&port->ip_lock);
-
- /* we need to remember the previous ones, to point back to
- * them farther down - setting up the ring buffers.
- */
- ports[phys_port] = port;
-
- /* init to something useful */
- card_ptr->ic_port[phys_port].icp_port = port;
- port->ip_is = is;
- port->ip_idd = idd;
- port->ip_baud = 9600;
- port->ip_card = card_ptr;
- port->ip_hooks = &hooks_array[phys_port];
-
- /* Setup each port */
- if (phys_port == 0) {
- port->ip_serial_regs = &idd->vma->port_a;
- port->ip_uart_regs = &idd->vma->sregs.uarta;
-
- DPRINT_CONFIG(("%s : Port A ip_serial_regs 0x%p "
- "ip_uart_regs 0x%p\n",
- __func__,
- (void *)port->ip_serial_regs,
- (void *)port->ip_uart_regs));
-
- /* setup ring buffers */
- port->ip_cpu_ringbuf = pci_alloc_consistent(pdev,
- TOTAL_RING_BUF_SIZE, &port->ip_dma_ringbuf);
-
- BUG_ON(!((((int64_t) port->ip_dma_ringbuf) &
- (TOTAL_RING_BUF_SIZE - 1)) == 0));
- port->ip_inring = RING(port, RX_A);
- port->ip_outring = RING(port, TX_A);
- DPRINT_CONFIG(("%s : Port A ip_cpu_ringbuf 0x%p "
- "ip_dma_ringbuf 0x%p, ip_inring 0x%p "
- "ip_outring 0x%p\n",
- __func__,
- (void *)port->ip_cpu_ringbuf,
- (void *)port->ip_dma_ringbuf,
- (void *)port->ip_inring,
- (void *)port->ip_outring));
- }
- else {
- port->ip_serial_regs = &idd->vma->port_b;
- port->ip_uart_regs = &idd->vma->sregs.uartb;
-
- DPRINT_CONFIG(("%s : Port B ip_serial_regs 0x%p "
- "ip_uart_regs 0x%p\n",
- __func__,
- (void *)port->ip_serial_regs,
- (void *)port->ip_uart_regs));
-
- /* share the ring buffers */
- port->ip_dma_ringbuf =
- ports[phys_port - 1]->ip_dma_ringbuf;
- port->ip_cpu_ringbuf =
- ports[phys_port - 1]->ip_cpu_ringbuf;
- port->ip_inring = RING(port, RX_B);
- port->ip_outring = RING(port, TX_B);
- DPRINT_CONFIG(("%s : Port B ip_cpu_ringbuf 0x%p "
- "ip_dma_ringbuf 0x%p, ip_inring 0x%p "
- "ip_outring 0x%p\n",
- __func__,
- (void *)port->ip_cpu_ringbuf,
- (void *)port->ip_dma_ringbuf,
- (void *)port->ip_inring,
- (void *)port->ip_outring));
- }
-
- DPRINT_CONFIG(("%s : port %d [addr 0x%p] card_ptr 0x%p",
- __func__,
- phys_port, (void *)port, (void *)card_ptr));
- DPRINT_CONFIG((" ip_serial_regs 0x%p ip_uart_regs 0x%p\n",
- (void *)port->ip_serial_regs,
- (void *)port->ip_uart_regs));
-
- /* Initialize the hardware for IOC3 */
- port_init(port);
-
- DPRINT_CONFIG(("%s: phys_port %d port 0x%p inring 0x%p "
- "outring 0x%p\n",
- __func__,
- phys_port, (void *)port,
- (void *)port->ip_inring,
- (void *)port->ip_outring));
-
- }
-
- /* register port with the serial core */
-
- ret = ioc3_serial_core_attach(is, idd);
- if (ret)
- goto out4;
-
- Num_of_ioc3_cards++;
-
- return ret;
-
- /* error exits that give back resources */
-out4:
- for (cnt = 0; cnt < phys_port; cnt++)
- kfree(ports[cnt]);
-
- kfree(card_ptr);
- return ret;
-}
-
-static struct ioc3_submodule ioc3uart_ops = {
- .name = "IOC3uart",
- .probe = ioc3uart_probe,
- .remove = ioc3uart_remove,
- /* call .intr for both ports initially */
- .irq_mask = SIO_IR_SA | SIO_IR_SB,
- .intr = ioc3uart_intr,
- .owner = THIS_MODULE,
-};
-
-/**
- * ioc3_detect - module init called,
- */
-static int __init ioc3uart_init(void)
-{
- int ret;
-
- /* register with serial core */
- if ((ret = uart_register_driver(&ioc3_uart)) < 0) {
- printk(KERN_WARNING
- "%s: Couldn't register IOC3 uart serial driver\n",
- __func__);
- return ret;
- }
- ret = ioc3_register_submodule(&ioc3uart_ops);
- if (ret)
- uart_unregister_driver(&ioc3_uart);
- return ret;
-}
-
-static void __exit ioc3uart_exit(void)
-{
- ioc3_unregister_submodule(&ioc3uart_ops);
- uart_unregister_driver(&ioc3_uart);
-}
-
-module_init(ioc3uart_init);
-module_exit(ioc3uart_exit);
-
-MODULE_AUTHOR("Pat Gefre - Silicon Graphics Inc. (SGI) <pfg@sgi.com>");
-MODULE_DESCRIPTION("Serial PCI driver module for SGI IOC3 card");
-MODULE_LICENSE("GPL");
The SGI SN2 support is about to be removed. Remove this driver that depends on the SN2 support. Signed-off-by: Christoph Hellwig <hch@lst.de> --- MAINTAINERS | 6 - arch/ia64/configs/gensparse_defconfig | 1 - drivers/tty/serial/Kconfig | 8 - drivers/tty/serial/Makefile | 1 - drivers/tty/serial/ioc3_serial.c | 2195 ------------------------- 5 files changed, 2211 deletions(-) delete mode 100644 drivers/tty/serial/ioc3_serial.c