diff mbox series

[mtd-utils] ubi-tests: mkvol test: Checks return value 'ENOSPC' for 'ubi_mkvol'

Message ID 1560514728-54932-1-git-send-email-chengzhihao1@huawei.com
State Accepted
Delegated to: David Oberhollenzer
Headers show
Series [mtd-utils] ubi-tests: mkvol test: Checks return value 'ENOSPC' for 'ubi_mkvol' | expand

Commit Message

Zhihao Cheng June 14, 2019, 12:18 p.m. UTC 
From: Zhihao Cheng <chengzhihao1@huawei.com>

UBI tests try to create too many volumes in mkvol_bad and mkvol_basic.
Currently mtd-utils allows return value 'ENFILE' from 'ubi_mkvol', that
works fine in most situations. But what if the number of PEBs equals to
the maximum count of volumes? For example, mkvol_basic test will fail in
a 64MiB flash with 512KiB PEB size.
Following is the output of mkvol_basic test:

  ======================================================================
  ======================================================================
  ======================================================================
  Test on mtdram, fastmap enabled, VID header offset factor 1
  ======================================================================
  ======================================================================
  ======================================================================
  mtdram: 64MiB, PEB size 512KiB, fastmap enabled
  Running mkvol_basic /dev/ubi0
  [mkvol_basic] mkvol_multiple():182: function ubi_mkvol() failed with
  error 28 (No space left on device)
  [mkvol_basic] mkvol_multiple():183: vol_id 122
  Error: mkvol_basic failed
  FAILURE

The reason is that there is no available PEB to support a new volume. We
can see following verbose in dmesg:

  ubi0: attached mtd0 (name "mtdram test device", size 64 MiB)
  ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
  ubi0: available PEBs: 122, total reserved PEBs: 6, PEBs reserved for
  bad PEB handling: 0

The maximum count of volumes is 128, so we can create 128 volumes
theoretically. But there are 122 available PEBs becauese of existence of
reserved PEBs. In addition, a volume occupies at least one PEB. Actually,
we can only create 122 volumes, Therefore, 'ubi_mkvol' returns 'ENOSPC'
when mkvol_basic tries to create 123rd volume. And we can see
corresponding error message in dmesg:

  ubi0 error: ubi_create_volume [ubi]: not enough PEBs, only 0 available
  ubi0 error: ubi_create_volume [ubi]: cannot create volume 122, error -28

So, 'ENOSPC' can happen before 'ENFILE' in flash with a small amount of
PEBs. This patch checks return value 'ENOSPC' for 'ubi_mkvol' when mkvol
test is trying to create too many volumes.

----------------------------------------

Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
---
 tests/ubi-tests/mkvol_bad.c   | 2 +-
 tests/ubi-tests/mkvol_basic.c | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

Comments

David Oberhollenzer June 17, 2019, 7:04 a.m. UTC | #1 
Applied to mtd-utils.git master.

Thanks,

David
diff mbox series

Patch

diff --git a/tests/ubi-tests/mkvol_bad.c b/tests/ubi-tests/mkvol_bad.c
index 7e46726..a5143e3 100644
--- a/tests/ubi-tests/mkvol_bad.c
+++ b/tests/ubi-tests/mkvol_bad.c
@@ -200,7 +200,7 @@  static int test_mkvol(void)
 			 * Note, because of gluebi we may be unable to create
 			 * dev_info.max_vol_count devices (MTD restrictions).
 			 */
-			if (errno == ENFILE)
+			if (errno == ENFILE || errno == ENOSPC)
 				break;
 			failed("ubi_mkvol");
 			errorm("vol_id %d", i);
diff --git a/tests/ubi-tests/mkvol_basic.c b/tests/ubi-tests/mkvol_basic.c
index c7c6984..cc3f7ba 100644
--- a/tests/ubi-tests/mkvol_basic.c
+++ b/tests/ubi-tests/mkvol_basic.c
@@ -178,7 +178,7 @@  static int mkvol_multiple(void)
 		req.name = nm;
 
 		if (ubi_mkvol(libubi, node, &req)) {
-			if (errno == ENFILE) {
+			if (errno == ENFILE || errno == ENOSPC) {
 				max = i;
 				break;
 			}