@@ -391,6 +391,7 @@ static int mtd_do_writeoob(struct file *file, struct mtd_info *mtd,
uint64_t start, uint32_t length, void __user *ptr,
uint32_t __user *retp)
{
+ struct mtd_file_info *mfi = file->private_data;
struct mtd_oob_ops ops;
uint32_t retlen;
int ret = 0;
@@ -412,7 +413,7 @@ static int mtd_do_writeoob(struct file *file, struct mtd_info *mtd,
ops.ooblen = length;
ops.ooboffs = start & (mtd->writesize - 1);
ops.datbuf = NULL;
- ops.mode = MTD_OOB_PLACE;
+ ops.mode = (mfi->mode == MTD_MODE_RAW) ? MTD_OOB_RAW : MTD_OOB_PLACE;
if (ops.ooboffs && ops.ooblen > (mtd->oobsize - ops.ooboffs))
return -EINVAL;
@@ -2401,7 +2401,12 @@ static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
chip->pagebuf = -1;
nand_fill_oob(mtd, ops->oobbuf, ops->ooblen, ops);
- status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask);
+
+ if (ops->mode == MTD_OOB_RAW) {
+ status = chip->ecc.write_oob_raw(mtd, chip, page & chip->pagemask);
+ } else {
+ status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask);
+ }
if (status)
return status;
@@ -3377,6 +3382,10 @@ int nand_scan_tail(struct mtd_info *mtd)
BUG();
}
+ /* For many systems, the standard OOB write also works for raw */
+ if (!chip->ecc.write_oob_raw)
+ chip->ecc.write_oob_raw = chip->ecc.write_oob;
+
/*
* The number of bytes available for a client to place data into
* the out of band area.
@@ -340,6 +340,7 @@ struct nand_hw_control {
* @read_subpage: function to read parts of the page covered by ECC.
* @write_page: function to write a page according to the ECC generator
* requirements.
+ * @write_oob_raw: function to write chip OOB data without ECC
* @read_oob: function to read chip OOB data
* @write_oob: function to write chip OOB data
*/
@@ -368,6 +369,8 @@ struct nand_ecc_ctrl {
uint32_t offs, uint32_t len, uint8_t *buf);
void (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
const uint8_t *buf);
+ int (*write_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip,
+ int page);
int (*read_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page,
int sndcmd);
int (*write_oob)(struct mtd_info *mtd, struct nand_chip *chip,
This fixes issues with `nandwrite -n -o' and the MEMWRITEOOB[64] ioctls on hardware that writes ECC when writing OOB. The problem arises as follows: `nandwrite -n' can write page data to flash without applying ECC, but when used with the `-o' option, ECC is applied (incorrectly), contrary to the `--noecc' option. I found that this is the case because my hardware computes and writes ECC data to flash upon either OOB write or page write. Thus, to support a proper "no ECC" write, my driver must know when we're performing a raw OOB write vs. a normal ECC OOB write. However, MTD does not pass any raw mode information to the write_oob functions. This patch addresses the problems by: 1) Passing MTD_OOB_RAW down to lower layers, instead of just defaulting to MTD_OOB_PLACE 2) Handling MTD_OOB_RAW within the NAND layer's `nand_do_write_oob' 3) Adding a new (replaceable) function pointer in struct ecc_ctrl; this function should support writing OOB without ECC data. Current hardware often can use the same OOB write function when writing either with or without ECC This was tested with nandsim as well as on actual SLC NAND. Signed-off-by: Brian Norris <computersforpeace@gmail.com> --- drivers/mtd/mtdchar.c | 3 ++- drivers/mtd/nand/nand_base.c | 11 ++++++++++- include/linux/mtd/nand.h | 3 +++ 3 files changed, 15 insertions(+), 2 deletions(-)