diff mbox

[U-Boot,v2,2/3] Armada100: Enable Ethernet support for GplugD

Message ID 1314191240-30938-2-git-send-email-ajay.bhargav@einfochips.com
State Superseded
Headers show

Commit Message

Ajay Bhargav Aug. 24, 2011, 1:07 p.m. UTC 
This patch enables ethernet support for Marvell GplugD board. Network
related commands works.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
---
Changes for v2:
	- armada100_fec_initialize changed to armada100_fec_register

 arch/arm/include/asm/arch-armada100/armada100.h |   57 +++++++++++++++++++++++
 arch/arm/include/asm/arch-armada100/mfp.h       |   19 ++++++++
 board/Marvell/gplugd/gplugd.c                   |   39 +++++++++++++++
 include/configs/gplugd.h                        |   19 +++++++-
 4 files changed, 132 insertions(+), 2 deletions(-)

Comments

Marek Vasut Aug. 24, 2011, 4:27 p.m. UTC | #1 
On Wednesday, August 24, 2011 03:07:19 PM Ajay Bhargav wrote:
> This patch enables ethernet support for Marvell GplugD board. Network
> related commands works.
> 
> Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
> ---
> Changes for v2:
> 	- armada100_fec_initialize changed to armada100_fec_register
> 
>  arch/arm/include/asm/arch-armada100/armada100.h |   57
> +++++++++++++++++++++++ arch/arm/include/asm/arch-armada100/mfp.h       | 
>  19 ++++++++
>  board/Marvell/gplugd/gplugd.c                   |   39 +++++++++++++++
>  include/configs/gplugd.h                        |   19 +++++++-
>  4 files changed, 132 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/include/asm/arch-armada100/armada100.h
> b/arch/arm/include/asm/arch-armada100/armada100.h index 3d567eb..849638d
> 100644
> --- a/arch/arm/include/asm/arch-armada100/armada100.h
> +++ b/arch/arm/include/asm/arch-armada100/armada100.h
> @@ -41,6 +41,10 @@
>  /* Functional Clock Selection Mask */
>  #define APBC_FNCLKSEL(x)        (((x) & 0xf) << 4)
> 
> +/* Fast Ethernet Controller Clock register definition */
> +#define FE_CLK_RST		0x1
> +#define FE_CLK_ENA		0x8
> +
>  /* Register Base Addresses */
>  #define ARMD1_DRAM_BASE		0xB0000000
>  #define ARMD1_TIMER_BASE	0xD4014000
> @@ -85,6 +89,59 @@ struct armd1mpmu_registers {
>  };
> 
>  /*
> + * Application Subsystem Power Management
> + * Refer Datasheet Appendix A.9
> + */
> +struct armd1apmu_registers {
> +	u32 pcr;		/* 0x000 */
> +	u32 ccr;		/* 0x004 */
> +	u32 pad1;
> +	u32 ccsr;		/* 0x00C */
> +	u32 fc_timer;		/* 0x010 */
> +	u32 pad2;
> +	u32 ideal_cfg;		/* 0x018 */
> +	u8 pad3[0x04C - 0x018 - 4];
> +	u32 lcdcrc;		/* 0x04C */
> +	u32 cciccrc;		/* 0x050 */
> +	u32 sd1crc;		/* 0x054 */
> +	u32 sd2crc;		/* 0x058 */
> +	u32 usbcrc;		/* 0x05C */
> +	u32 nfccrc;		/* 0x060 */
> +	u32 dmacrc;		/* 0x064 */
> +	u32 pad4;
> +	u32 buscrc;		/* 0x06C */
> +	u8 pad5[0x07C - 0x06C - 4];
> +	u32 wake_clr;		/* 0x07C */
> +	u8 pad6[0x090 - 0x07C - 4];
> +	u32 core_status;	/* 0x090 */
> +	u32 rfsc;		/* 0x094 */
> +	u32 imr;		/* 0x098 */
> +	u32 irwc;		/* 0x09C */
> +	u32 isr;		/* 0x0A0 */
> +	u8 pad7[0x0B0 - 0x0A0 - 4];
> +	u32 mhst;		/* 0x0B0 */
> +	u32 msr;		/* 0x0B4 */
> +	u8 pad8[0x0C0 - 0x0B4 - 4];
> +	u32 msst;		/* 0x0C0 */
> +	u32 pllss;		/* 0x0C4 */
> +	u32 smb;		/* 0x0C8 */
> +	u32 gccrc;		/* 0x0CC */
> +	u8 pad9[0x0D4 - 0x0CC - 4];
> +	u32 smccrc;		/* 0x0D4 */
> +	u32 pad10;
> +	u32 xdcrc;		/* 0x0DC */
> +	u32 sd3crc;		/* 0x0E0 */
> +	u32 sd4crc;		/* 0x0E4 */
> +	u8 pad11[0x0F0 - 0x0E4 - 4];
> +	u32 cfcrc;		/* 0x0F0 */
> +	u32 mspcrc;		/* 0x0F4 */
> +	u32 cmucrc;		/* 0x0F8 */
> +	u32 fecrc;		/* 0x0FC */
> +	u32 pciecrc;		/* 0x100 */
> +	u32 epdcrc;		/* 0x104 */
> +};
> +
> +/*
>   * APB1 Clock Reset/Control Registers
>   * Refer Datasheet Appendix A.10
>   */
> diff --git a/arch/arm/include/asm/arch-armada100/mfp.h
> b/arch/arm/include/asm/arch-armada100/mfp.h index d6e0494..da76b58 100644
> --- a/arch/arm/include/asm/arch-armada100/mfp.h
> +++ b/arch/arm/include/asm/arch-armada100/mfp.h
> @@ -64,6 +64,25 @@
>  #define MFP105_CI2C_SDA		(MFP_REG(0x1a4) | MFP_AF1 | MFP_DRIVE_MEDIUM)
>  #define MFP106_CI2C_SCL		(MFP_REG(0x1a8) | MFP_AF1 | MFP_DRIVE_MEDIUM)
> 
> +/* Fast Ethernet */
> +#define MFP086_ETH_TXCLK	(MFP_REG(0x158) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP087_ETH_TXEN		(MFP_REG(0x15C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP088_ETH_TXDQ3	(MFP_REG(0x160) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP089_ETH_TXDQ2	(MFP_REG(0x164) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP090_ETH_TXDQ1	(MFP_REG(0x168) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP091_ETH_TXDQ0	(MFP_REG(0x16C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP092_ETH_CRS		(MFP_REG(0x170) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP093_ETH_COL		(MFP_REG(0x174) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP094_ETH_RXCLK	(MFP_REG(0x178) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP095_ETH_RXER		(MFP_REG(0x17C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP096_ETH_RXDQ3	(MFP_REG(0x180) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP097_ETH_RXDQ2	(MFP_REG(0x184) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP098_ETH_RXDQ1	(MFP_REG(0x188) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP099_ETH_RXDQ0	(MFP_REG(0x18C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP100_ETH_MDC		(MFP_REG(0x190) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP101_ETH_MDIO		(MFP_REG(0x194) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +#define MFP103_ETH_RXDV		(MFP_REG(0x19C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
> +
>  /* More macros can be defined here... */
> 
>  #define MFP_PIN_MAX	117
> diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c
> index dc7d89d..4cd4086 100644
> --- a/board/Marvell/gplugd/gplugd.c
> +++ b/board/Marvell/gplugd/gplugd.c
> @@ -33,6 +33,11 @@
>  #include <asm/arch/mfp.h>
>  #include <asm/arch/armada100.h>
> 
> +#ifdef CONFIG_ARMADA100_FEC
> +#include <net.h>
> +#include <netdev.h>
> +#endif /* CONFIG_ARMADA100_FEC */
> +
>  DECLARE_GLOBAL_DATA_PTR;
> 
>  int board_early_init_f(void)
> @@ -45,6 +50,26 @@ int board_early_init_f(void)
>  		/* Enable Console on UART3 */
>  		MFPO8_UART3_TXD,
>  		MFPO9_UART3_RXD,
> +
> +		/* Ethernet PHY Interface */
> +		MFP086_ETH_TXCLK,
> +		MFP087_ETH_TXEN,
> +		MFP088_ETH_TXDQ3,
> +		MFP089_ETH_TXDQ2,
> +		MFP090_ETH_TXDQ1,
> +		MFP091_ETH_TXDQ0,
> +		MFP092_ETH_CRS,
> +		MFP093_ETH_COL,
> +		MFP094_ETH_RXCLK,
> +		MFP095_ETH_RXER,
> +		MFP096_ETH_RXDQ3,
> +		MFP097_ETH_RXDQ2,
> +		MFP098_ETH_RXDQ1,
> +		MFP099_ETH_RXDQ0,
> +		MFP100_ETH_MDC,
> +		MFP101_ETH_MDIO,
> +		MFP103_ETH_RXDV,
> +
>  		MFP_EOC		/*End of configuration*/
>  	};
>  	/* configure MFP's */
> @@ -60,3 +85,17 @@ int board_init(void)
>  	gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
>  	return 0;
>  }
> +
> +#ifdef CONFIG_ARMADA100_FEC
> +int board_eth_init(bd_t *bis)
> +{
> +	struct armd1apmu_registers *apmu_regs =
> +		(struct armd1apmu_registers *) ARMD1_APMU_BASE;
> +
> +	/* Enable clock of ethernet controller */
> +	writel(FE_CLK_RST | FE_CLK_ENA, &apmu_regs->fecrc);
> +
> +	return armada100_fec_register();
> +}
> +#endif /* CONFIG_ARMADA100_FEC */
> +
> diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h
> index cc14f49..f3b94d8 100644
> --- a/include/configs/gplugd.h
> +++ b/include/configs/gplugd.h
> @@ -62,8 +62,23 @@
>  #define CONFIG_CMD_I2C
>  #define CONFIG_CMD_AUTOSCRIPT
>  #undef CONFIG_CMD_FPGA
> -#undef CONFIG_CMD_NET
> -#undef CONFIG_CMD_NFS
> +
> +/* Disable DCACHE */
> +#define CONFIG_SYS_DCACHE_OFF

ARMADA100 is still ARMv5? Then maybe you can try Hong Xu's patches for dcache on 
armv5. You'll have to modify the ethernet driver to be aware of the dcache then 
though.

As dcache support is on the way, it might be worth it.

> +
> +/* Network configuration */
> +#define CONFIG_CMD_PING
> +#define CONFIG_NET_MULTI
> +#define CONFIG_ARMADA100_FEC
> +
> +/* DHCP Support */
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_BOOTP_DHCP_REQUEST_DELAY		50000
> +#define CONFIG_BOOTP_SERVERIP
> +
> +/* Default Boot Parameters */
> +#define CONFIG_ROOTPATH				"/tftpboot"
> +#define CONFIG_SYS_IMG_NAME			"uImage"
> 
>  /*
>   * mv-common.h should be defined after CMD configs since it used them
Ajay Bhargav Aug. 25, 2011, 5:15 a.m. UTC | #2 
----- "Marek Vasut" <marek.vasut@gmail.com> wrote:
[...]
> > +/* Disable DCACHE */
> > +#define CONFIG_SYS_DCACHE_OFF
> 
> ARMADA100 is still ARMv5? Then maybe you can try Hong Xu's patches for
> dcache on 
> armv5. You'll have to modify the ethernet driver to be aware of the
> dcache then 
> though.
> 
> As dcache support is on the way, it might be worth it.
> 

Yes ARMADA100 is ARMv5. I had problems with dcache enabled, driver get stuck.
Can you please link me to Hong Xu's patches? Is there a problem if i keep it
disabled?

Thanks,
Ajay Bhargav
Marek Vasut Aug. 25, 2011, 12:12 p.m. UTC | #3 
On Thursday, August 25, 2011 07:15:17 AM Ajay Bhargav wrote:
> ----- "Marek Vasut" <marek.vasut@gmail.com> wrote:
> [...]
> 
> > > +/* Disable DCACHE */
> > > +#define CONFIG_SYS_DCACHE_OFF
> > 
> > ARMADA100 is still ARMv5? Then maybe you can try Hong Xu's patches for
> > dcache on
> > armv5. You'll have to modify the ethernet driver to be aware of the
> > dcache then
> > though.
> > 
> > As dcache support is on the way, it might be worth it.
> 
> Yes ARMADA100 is ARMv5. I had problems with dcache enabled, driver get
> stuck. Can you please link me to Hong Xu's patches? Is there a problem if
> i keep it disabled?

http://lists.denx.de/pipermail/u-boot/2011-August/098405.html Look around this. 
You'd better search for V2 of the patches or V3 in U-Boot ML archive.

There's no problem if you keep it disabled, but eventually, you'll have to 
enable it ;-)

Cheers
> 
> Thanks,
> Ajay Bhargav
diff mbox

Patch

diff --git a/arch/arm/include/asm/arch-armada100/armada100.h b/arch/arm/include/asm/arch-armada100/armada100.h
index 3d567eb..849638d 100644
--- a/arch/arm/include/asm/arch-armada100/armada100.h
+++ b/arch/arm/include/asm/arch-armada100/armada100.h
@@ -41,6 +41,10 @@ 
 /* Functional Clock Selection Mask */
 #define APBC_FNCLKSEL(x)        (((x) & 0xf) << 4)
 
+/* Fast Ethernet Controller Clock register definition */
+#define FE_CLK_RST		0x1
+#define FE_CLK_ENA		0x8
+
 /* Register Base Addresses */
 #define ARMD1_DRAM_BASE		0xB0000000
 #define ARMD1_TIMER_BASE	0xD4014000
@@ -85,6 +89,59 @@  struct armd1mpmu_registers {
 };
 
 /*
+ * Application Subsystem Power Management
+ * Refer Datasheet Appendix A.9
+ */
+struct armd1apmu_registers {
+	u32 pcr;		/* 0x000 */
+	u32 ccr;		/* 0x004 */
+	u32 pad1;
+	u32 ccsr;		/* 0x00C */
+	u32 fc_timer;		/* 0x010 */
+	u32 pad2;
+	u32 ideal_cfg;		/* 0x018 */
+	u8 pad3[0x04C - 0x018 - 4];
+	u32 lcdcrc;		/* 0x04C */
+	u32 cciccrc;		/* 0x050 */
+	u32 sd1crc;		/* 0x054 */
+	u32 sd2crc;		/* 0x058 */
+	u32 usbcrc;		/* 0x05C */
+	u32 nfccrc;		/* 0x060 */
+	u32 dmacrc;		/* 0x064 */
+	u32 pad4;
+	u32 buscrc;		/* 0x06C */
+	u8 pad5[0x07C - 0x06C - 4];
+	u32 wake_clr;		/* 0x07C */
+	u8 pad6[0x090 - 0x07C - 4];
+	u32 core_status;	/* 0x090 */
+	u32 rfsc;		/* 0x094 */
+	u32 imr;		/* 0x098 */
+	u32 irwc;		/* 0x09C */
+	u32 isr;		/* 0x0A0 */
+	u8 pad7[0x0B0 - 0x0A0 - 4];
+	u32 mhst;		/* 0x0B0 */
+	u32 msr;		/* 0x0B4 */
+	u8 pad8[0x0C0 - 0x0B4 - 4];
+	u32 msst;		/* 0x0C0 */
+	u32 pllss;		/* 0x0C4 */
+	u32 smb;		/* 0x0C8 */
+	u32 gccrc;		/* 0x0CC */
+	u8 pad9[0x0D4 - 0x0CC - 4];
+	u32 smccrc;		/* 0x0D4 */
+	u32 pad10;
+	u32 xdcrc;		/* 0x0DC */
+	u32 sd3crc;		/* 0x0E0 */
+	u32 sd4crc;		/* 0x0E4 */
+	u8 pad11[0x0F0 - 0x0E4 - 4];
+	u32 cfcrc;		/* 0x0F0 */
+	u32 mspcrc;		/* 0x0F4 */
+	u32 cmucrc;		/* 0x0F8 */
+	u32 fecrc;		/* 0x0FC */
+	u32 pciecrc;		/* 0x100 */
+	u32 epdcrc;		/* 0x104 */
+};
+
+/*
  * APB1 Clock Reset/Control Registers
  * Refer Datasheet Appendix A.10
  */
diff --git a/arch/arm/include/asm/arch-armada100/mfp.h b/arch/arm/include/asm/arch-armada100/mfp.h
index d6e0494..da76b58 100644
--- a/arch/arm/include/asm/arch-armada100/mfp.h
+++ b/arch/arm/include/asm/arch-armada100/mfp.h
@@ -64,6 +64,25 @@ 
 #define MFP105_CI2C_SDA		(MFP_REG(0x1a4) | MFP_AF1 | MFP_DRIVE_MEDIUM)
 #define MFP106_CI2C_SCL		(MFP_REG(0x1a8) | MFP_AF1 | MFP_DRIVE_MEDIUM)
 
+/* Fast Ethernet */
+#define MFP086_ETH_TXCLK	(MFP_REG(0x158) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP087_ETH_TXEN		(MFP_REG(0x15C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP088_ETH_TXDQ3	(MFP_REG(0x160) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP089_ETH_TXDQ2	(MFP_REG(0x164) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP090_ETH_TXDQ1	(MFP_REG(0x168) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP091_ETH_TXDQ0	(MFP_REG(0x16C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP092_ETH_CRS		(MFP_REG(0x170) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP093_ETH_COL		(MFP_REG(0x174) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP094_ETH_RXCLK	(MFP_REG(0x178) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP095_ETH_RXER		(MFP_REG(0x17C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP096_ETH_RXDQ3	(MFP_REG(0x180) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP097_ETH_RXDQ2	(MFP_REG(0x184) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP098_ETH_RXDQ1	(MFP_REG(0x188) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP099_ETH_RXDQ0	(MFP_REG(0x18C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP100_ETH_MDC		(MFP_REG(0x190) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP101_ETH_MDIO		(MFP_REG(0x194) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+#define MFP103_ETH_RXDV		(MFP_REG(0x19C) | MFP_AF5 | MFP_DRIVE_MEDIUM)
+
 /* More macros can be defined here... */
 
 #define MFP_PIN_MAX	117
diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c
index dc7d89d..4cd4086 100644
--- a/board/Marvell/gplugd/gplugd.c
+++ b/board/Marvell/gplugd/gplugd.c
@@ -33,6 +33,11 @@ 
 #include <asm/arch/mfp.h>
 #include <asm/arch/armada100.h>
 
+#ifdef CONFIG_ARMADA100_FEC
+#include <net.h>
+#include <netdev.h>
+#endif /* CONFIG_ARMADA100_FEC */
+
 DECLARE_GLOBAL_DATA_PTR;
 
 int board_early_init_f(void)
@@ -45,6 +50,26 @@  int board_early_init_f(void)
 		/* Enable Console on UART3 */
 		MFPO8_UART3_TXD,
 		MFPO9_UART3_RXD,
+
+		/* Ethernet PHY Interface */
+		MFP086_ETH_TXCLK,
+		MFP087_ETH_TXEN,
+		MFP088_ETH_TXDQ3,
+		MFP089_ETH_TXDQ2,
+		MFP090_ETH_TXDQ1,
+		MFP091_ETH_TXDQ0,
+		MFP092_ETH_CRS,
+		MFP093_ETH_COL,
+		MFP094_ETH_RXCLK,
+		MFP095_ETH_RXER,
+		MFP096_ETH_RXDQ3,
+		MFP097_ETH_RXDQ2,
+		MFP098_ETH_RXDQ1,
+		MFP099_ETH_RXDQ0,
+		MFP100_ETH_MDC,
+		MFP101_ETH_MDIO,
+		MFP103_ETH_RXDV,
+
 		MFP_EOC		/*End of configuration*/
 	};
 	/* configure MFP's */
@@ -60,3 +85,17 @@  int board_init(void)
 	gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
 	return 0;
 }
+
+#ifdef CONFIG_ARMADA100_FEC
+int board_eth_init(bd_t *bis)
+{
+	struct armd1apmu_registers *apmu_regs =
+		(struct armd1apmu_registers *) ARMD1_APMU_BASE;
+
+	/* Enable clock of ethernet controller */
+	writel(FE_CLK_RST | FE_CLK_ENA, &apmu_regs->fecrc);
+
+	return armada100_fec_register();
+}
+#endif /* CONFIG_ARMADA100_FEC */
+
diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h
index cc14f49..f3b94d8 100644
--- a/include/configs/gplugd.h
+++ b/include/configs/gplugd.h
@@ -62,8 +62,23 @@ 
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_AUTOSCRIPT
 #undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
+
+/* Disable DCACHE */
+#define CONFIG_SYS_DCACHE_OFF
+
+/* Network configuration */
+#define CONFIG_CMD_PING
+#define CONFIG_NET_MULTI
+#define CONFIG_ARMADA100_FEC
+
+/* DHCP Support */
+#define CONFIG_CMD_DHCP
+#define CONFIG_BOOTP_DHCP_REQUEST_DELAY		50000
+#define CONFIG_BOOTP_SERVERIP
+
+/* Default Boot Parameters */
+#define CONFIG_ROOTPATH				"/tftpboot"
+#define CONFIG_SYS_IMG_NAME			"uImage"
 
 /*
  * mv-common.h should be defined after CMD configs since it used them