diff mbox

[U-Boot,15/15] MX5: mx51evk: make use of GPIO framework

Message ID 1313999739-1205-1-git-send-email-sbabic@denx.de
State Accepted
Commit 753fc2ebf98a5112fd1dea4ea0806548c741beaf
Headers show

Commit Message

Stefano Babic Aug. 22, 2011, 7:55 a.m. UTC 
Signed-off-by: Stefano Babic <sbabic@denx.de>
---
 board/freescale/mx51evk/mx51evk.c |   18 +++++-------------
 include/configs/mx51evk.h         |    1 +
 2 files changed, 6 insertions(+), 13 deletions(-)
diff mbox

Patch

diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c
index fd7342f..94ea1f2 100644
--- a/board/freescale/mx51evk/mx51evk.c
+++ b/board/freescale/mx51evk/mx51evk.c
@@ -22,6 +22,7 @@ 
 
 #include <common.h>
 #include <asm/io.h>
+#include <asm/gpio.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/mx5x_pins.h>
 #include <asm/arch/iomux.h>
@@ -180,7 +181,6 @@  static void setup_iomux_spi(void)
 static void power_init(void)
 {
 	unsigned int val;
-	unsigned int reg;
 	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE;
 
 	/* Write needed to Power Gate 2 register */
@@ -249,13 +249,7 @@  static void power_init(void)
 	pmic_reg_write(REG_MODE_1, val);
 	udelay(200);
 
-	reg = readl(GPIO2_BASE_ADDR + 0x0);
-	reg &= ~0x4000;  /* Lower reset line */
-	writel(reg, GPIO2_BASE_ADDR + 0x0);
-
-	reg = readl(GPIO2_BASE_ADDR + 0x4);
-	reg |= 0x4000;	/* configure GPIO lines as output */
-	writel(reg, GPIO2_BASE_ADDR + 0x4);
+	gpio_direction_output(46, 0);
 
 	/* Reset the ethernet controller over GPIO */
 	writel(0x1, IOMUXC_BASE_ADDR + 0x0AC);
@@ -267,9 +261,7 @@  static void power_init(void)
 
 	udelay(500);
 
-	reg = readl(GPIO2_BASE_ADDR + 0x0);
-	reg |= 0x4000;
-	writel(reg, GPIO2_BASE_ADDR + 0x0);
+	gpio_set_value(46, 1);
 }
 
 #ifdef CONFIG_FSL_ESDHC
@@ -278,9 +270,9 @@  int board_mmc_getcd(u8 *cd, struct mmc *mmc)
 	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 
 	if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
-		*cd = readl(GPIO1_BASE_ADDR) & 0x01;
+		*cd = gpio_get_value(0);
 	else
-		*cd = readl(GPIO1_BASE_ADDR) & 0x40;
+		*cd = gpio_get_value(6);
 
 	return 0;
 }
diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h
index 3f2aca1..7d05dc8 100644
--- a/include/configs/mx51evk.h
+++ b/include/configs/mx51evk.h
@@ -60,6 +60,7 @@ 
  */
 #define CONFIG_MXC_UART
 #define CONFIG_SYS_MX51_UART1
+#define CONFIG_MXC_GPIO
 
 /*
  * SPI Configs