spi: dt-bindings: Convert Arm pl022 to json-schema
diff mbox series

Message ID 20190521212325.16639-1-robh@kernel.org
State Not Applicable
Headers show
Series
  • spi: dt-bindings: Convert Arm pl022 to json-schema
Related show

Checks

Context Check Description
robh/dt-meta-schema fail build log
robh/checkpatch warning "total: 0 errors, 1 warnings, 165 lines checked"

Commit Message

Rob Herring May 21, 2019, 9:23 p.m. UTC
Convert the Arm pl022 binding to DT schema format. The clock binding was
missing, so it is added to the schema. It really should be required as
well, but there are some platforms (spear) not yet using DT clock
binding.

Cc: Mark Brown <broonie@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-spi@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/spi/spi-pl022.yaml    | 165 ++++++++++++++++++
 .../devicetree/bindings/spi/spi_pl022.txt     |  70 --------
 2 files changed, 165 insertions(+), 70 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/spi/spi-pl022.yaml
 delete mode 100644 Documentation/devicetree/bindings/spi/spi_pl022.txt

Comments

Maxime Ripard May 22, 2019, 10:42 a.m. UTC | #1
Hi Rob,

On Tue, May 21, 2019 at 04:23:24PM -0500, Rob Herring wrote:
> +allOf:
> +  - $ref: "spi-controller.yaml#"

You're using a different construct on the spi-gpio binding you just
sent (/schemas/spi/spi-controller.yaml).

Is that on purpose?

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Rob Herring May 22, 2019, 12:49 p.m. UTC | #2
On Wed, May 22, 2019 at 5:42 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
>
> Hi Rob,
>
> On Tue, May 21, 2019 at 04:23:24PM -0500, Rob Herring wrote:
> > +allOf:
> > +  - $ref: "spi-controller.yaml#"
>
> You're using a different construct on the spi-gpio binding you just
> sent (/schemas/spi/spi-controller.yaml).
>
> Is that on purpose?

No. This one is correct (though both work).

Rob

Patch
diff mbox series

diff --git a/Documentation/devicetree/bindings/spi/spi-pl022.yaml b/Documentation/devicetree/bindings/spi/spi-pl022.yaml
new file mode 100644
index 000000000000..dfb697c69341
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-pl022.yaml
@@ -0,0 +1,165 @@ 
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-pl022.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ARM PL022 SPI controller
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+# We need a select here so we don't match all nodes with 'arm,primecell'
+select:
+  properties:
+    compatible:
+      contains:
+        const: arm,pl022
+  required:
+    - compatible
+
+properties:
+  compatible:
+    items:
+      - const: arm,pl022
+      - const: arm,primecell
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - enum:
+          - SSPCLK
+          - sspclk
+      - const: apb_pclk
+
+  pl022,autosuspend-delay:
+    description: delay in ms following transfer completion before the
+      runtime power management system suspends the device. A setting of 0
+      indicates no delay and the device will be suspended immediately.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+  pl022,rt:
+    description: indicates the controller should run the message pump with realtime
+               priority to minimise the transfer latency on the bus (boolean)
+    type: boolean
+
+  dmas:
+    description:
+      Two or more DMA channel specifiers following the convention outlined
+      in bindings/dma/dma.txt
+    minItems: 2
+    maxItems: 32
+
+  dma-names:
+    description:
+      There must be at least one channel named "tx" for transmit and named "rx"
+      for receive.
+    minItems: 2
+    maxItems: 32
+    additionalItems: true
+    items:
+      - const: rx
+      - const: tx
+
+patternProperties:
+  "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$":
+    type: object
+    # SPI slave nodes must be children of the SPI master node and can
+    # contain the following properties.
+    properties:
+      pl022,interface:
+        description: SPI interface type
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum:
+              - 0  # SPI
+              - 1  # Texas Instruments Synchronous Serial Frame Format
+              - 2  # Microwire (Half Duplex)
+
+      pl022,com-mode:
+        description: Specifies the transfer mode
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum:
+              - 0  # interrupt mode
+              - 1  # polling mode
+              - 2  # DMA mode
+            default: 1
+
+      pl022,rx-level-trig:
+        description: Rx FIFO watermark level
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 4
+
+      pl022,tx-level-trig:
+        description: Tx FIFO watermark level
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0
+            maximum: 4
+
+      pl022,ctrl-len:
+        description: Microwire interface - Control length
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - minimum: 0x03
+            maximum: 0x1f
+
+      pl022,wait-state:
+        description: Microwire interface - Wait state
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum: [ 0, 1 ]
+
+      pl022,duplex:
+        description: Microwire interface - Full/Half duplex
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/uint32"
+          - enum: [ 0, 1 ]
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    spi@e0100000 {
+      compatible = "arm,pl022", "arm,primecell";
+      reg = <0xe0100000 0x1000>;
+      #address-cells = <1>;
+      #size-cells = <0>;
+      interrupts = <0 31 0x4>;
+      dmas = <&dma_controller 23 1>,
+        <&dma_controller 24 0>;
+      dma-names = "rx", "tx";
+
+      m25p80@1 {
+        compatible = "st,m25p80";
+        reg = <1>;
+        spi-max-frequency = <12000000>;
+        spi-cpol;
+        spi-cpha;
+        pl022,interface = <0>;
+        pl022,com-mode = <0x2>;
+        pl022,rx-level-trig = <0>;
+        pl022,tx-level-trig = <0>;
+        pl022,ctrl-len = <0x11>;
+        pl022,wait-state = <0>;
+        pl022,duplex = <0>;
+      };
+    };
+...
diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt
deleted file mode 100644
index 7638b4968ddb..000000000000
--- a/Documentation/devicetree/bindings/spi/spi_pl022.txt
+++ /dev/null
@@ -1,70 +0,0 @@ 
-ARM PL022 SPI controller
-
-Required properties:
-- compatible : "arm,pl022", "arm,primecell"
-- reg : Offset and length of the register set for the device
-- interrupts : Should contain SPI controller interrupt
-- num-cs : total number of chipselects
-
-Optional properties:
-- cs-gpios : should specify GPIOs used for chipselects.
-  The gpios will be referred to as reg = <index> in the SPI child nodes.
-  If unspecified, a single SPI device without a chip select can be used.
-- pl022,autosuspend-delay : delay in ms following transfer completion before
-			    the runtime power management system suspends the
-			    device. A setting of 0 indicates no delay and the
-                            device will be suspended immediately
-- pl022,rt : indicates the controller should run the message pump with realtime
-             priority to minimise the transfer latency on the bus (boolean)
-- dmas : Two or more DMA channel specifiers following the convention outlined
-         in bindings/dma/dma.txt
-- dma-names: Names for the dma channels, if present. There must be at
-	     least one channel named "tx" for transmit and named "rx" for
-             receive.
-
-
-SPI slave nodes must be children of the SPI master node and can
-contain the following properties.
-
-- pl022,interface : interface type:
-	0: SPI
-	1: Texas Instruments Synchronous Serial Frame Format
-	2: Microwire (Half Duplex)
-- pl022,com-mode : specifies the transfer mode:
-	0: interrupt mode
-	1: polling mode (default mode if property not present)
-	2: DMA mode
-- pl022,rx-level-trig : Rx FIFO watermark level
-- pl022,tx-level-trig : Tx FIFO watermark level
-- pl022,ctrl-len : Microwire interface: Control length
-- pl022,wait-state : Microwire interface: Wait state
-- pl022,duplex : Microwire interface: Full/Half duplex
-
-
-Example:
-
-	spi@e0100000 {
-		compatible = "arm,pl022", "arm,primecell";
-		reg = <0xe0100000 0x1000>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupts = <0 31 0x4>;
-		dmas = <&dma-controller 23 1>,
-			<&dma-controller 24 0>;
-		dma-names = "rx", "tx";
-
-		m25p80@1 {
-			compatible = "st,m25p80";
-			reg = <1>;
-			spi-max-frequency = <12000000>;
-			spi-cpol;
-			spi-cpha;
-			pl022,interface = <0>;
-			pl022,com-mode = <0x2>;
-			pl022,rx-level-trig = <0>;
-			pl022,tx-level-trig = <0>;
-			pl022,ctrl-len = <0x11>;
-			pl022,wait-state = <0>;
-			pl022,duplex = <0>;
-		};
-	};