@@ -60,3 +60,5 @@ CONFIG_SPL_SPI_FLASH_SUPPORT (drivers/mtd/spi/libspi_flash.o)
CONFIG_SPL_SPI_SUPPORT (drivers/spi/libspi.o)
CONFIG_SPL_FAT_SUPPORT (fs/fat/libfat.o)
CONFIG_SPL_LIBGENERIC_SUPPORT (lib/libgeneric.o)
+CONFIG_SPL_POWER_SUPPORT (drivers/power/libpower.o)
+CONFIG_SPL_NAND_SUPPORT (drivers/mtd/nand/libnand.o)
@@ -26,12 +26,19 @@ include $(TOPDIR)/config.mk
LIB := $(obj)libnand.o
ifdef CONFIG_CMD_NAND
+ifdef CONFIG_SPL_BUILD
+COBJS-y += nand_spl.o
+ifdef CONFIG_OMAP34XX
+COBJS-y += nand_ecc.o
+endif
+else
COBJS-y += nand.o
COBJS-y += nand_base.o
COBJS-y += nand_bbt.o
-COBJS-y += nand_ecc.o
COBJS-y += nand_ids.o
COBJS-y += nand_util.o
+COBJS-y += nand_ecc.o
+endif
COBJS-$(CONFIG_NAND_ATMEL) += atmel_nand.o
COBJS-$(CONFIG_DRIVER_NAND_BFIN) += bfin_nand.o
@@ -61,6 +61,55 @@ static void omap_nand_hwcontrol(struct mtd_info *mtd, int32_t cmd,
writeb(cmd, this->IO_ADDR_W);
}
+#ifdef CONFIG_SPL_BUILD
+/* Check wait pin as dev ready indicator */
+int omap_spl_dev_ready(struct mtd_info *mtd)
+{
+ return gpmc_cfg->status & (1 << 8);
+}
+
+/*
+ * omap_spl_read_buf16 - [DEFAULT] read chip data into buffer
+ * @mtd: MTD device structure
+ * @buf: buffer to store date
+ * @len: number of bytes to read
+ *
+ * Default read function for 16bit buswith
+ *
+ * This function is based on nand_read_buf16 from nand_base.c. This version
+ * reads 32bit not 16bit although the bus only has 16bit.
+ */
+static void omap_spl_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ int i;
+ struct nand_chip *chip = mtd->priv;
+ u32 *p = (u32 *) buf;
+ len >>= 2;
+
+ for (i = 0; i < len; i++)
+ p[i] = readl(chip->IO_ADDR_R);
+}
+
+/*
+ * omap_spl_read_buf - [DEFAULT] read chip data into buffer
+ * @mtd: MTD device structure
+ * @buf: buffer to store date
+ * @len: number of bytes to read
+ *
+ * Default read function for 8bit buswith
+ *
+ * This is the same function as this from nand_base.c nand_read_buf
+ */
+static void omap_spl_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ int i;
+ struct nand_chip *chip = mtd->priv;
+
+ for (i = 0; i < len; i++)
+ buf[i] = readb(chip->IO_ADDR_R);
+}
+#endif
+
/*
* omap_hwecc_init - Initialize the Hardware ECC for NAND flash in
* GPMC controller
@@ -224,6 +273,7 @@ static void omap_enable_hwecc(struct mtd_info *mtd, int32_t mode)
}
}
+#ifndef CONFIG_SPL_BUILD
/*
* omap_nand_switch_ecc - switch the ECC operation b/w h/w ecc and s/w ecc.
* The default is to come up on s/w ecc
@@ -280,6 +330,7 @@ void omap_nand_switch_ecc(int32_t hardware)
nand->options &= ~NAND_OWN_BUFFERS;
}
+#endif /* CONFIG_SPL_BUILD */
/*
* Board-specific NAND initialization. The following members of the
@@ -338,7 +389,24 @@ int board_nand_init(struct nand_chip *nand)
nand->chip_delay = 100;
/* Default ECC mode */
+#ifndef CONFIG_SPL_BUILD
nand->ecc.mode = NAND_ECC_SOFT;
+#else
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.layout = &hw_nand_oob;
+ nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE;
+ nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES;
+ nand->ecc.hwctl = omap_enable_hwecc;
+ nand->ecc.correct = omap_correct_data;
+ nand->ecc.calculate = omap_calculate_ecc;
+ omap_hwecc_init(nand);
+
+ if (nand->options & NAND_BUSWIDTH_16)
+ nand->read_buf = omap_spl_read_buf16;
+ else
+ nand->read_buf = omap_spl_read_buf;
+ nand->dev_ready = omap_spl_dev_ready;
+#endif
return 0;
}
@@ -46,6 +46,8 @@ LIBS-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += drivers/mtd/spi/libspi_flash.o
LIBS-$(CONFIG_SPL_SPI_SUPPORT) += drivers/spi/libspi.o
LIBS-$(CONFIG_SPL_FAT_SUPPORT) += fs/fat/libfat.o
LIBS-$(CONFIG_SPL_LIBGENERIC_SUPPORT) += lib/libgeneric.o
+LIBS-$(CONFIG_SPL_POWER_SUPPORT) += drivers/power/libpower.o
+LIBS-$(CONFIG_SPL_NAND_SUPPORT) += drivers/mtd/nand/libnand.o
ifeq ($(SOC),omap3)
LIBS-y += $(CPUDIR)/omap-common/libomap-common.o
Insert some NAND driver sources into NAND SPL library. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> --- V1 changes: CHG Default to HW ecc in SPL build ADD nand_read_buf16 function, read buffer ADD omap_dev_ready function, indicte if chip is ready V2 changes: DEL GPMC_WAIT0_PIN_ACTIVE define CHG omap_dev_ready() renamed to omap_spl_dev_ready(), does not use the GPMC_WAIT0_PIN_ACTIVE-define anymore CHG ogpmc_read_buf16 renamed omap_spl_read_buf16 ADD omap_spl_read_buf, 8x buf read function ADD CONFIG_SPL_POWER_SUPPORT and CONFIG_SPL_NAND_SUPPORT to SPL CHG cosmetic CHG nand_base and nand_bbt aren't needed for SPL anymore CHG omap_nand_switch_ecc is not compiled for SPL ADD entry for CONFIG_SPL_POWER_SUPPORT and CONFIG_SPL_NAND_SUPPORT to README.SPL V3 changes: DEL cosmetic (empty line) V4 changes: nothing V5 changes: CHG nand_ecc.o is only compiled for SPL if CONFIG_OMAP34XX is set Transition from V1 to V2 also includes that this patch is now based on - the new SPL layout by Aneesh V and Daniel Schwierzeck - the OMAP4 SPL patches by Aneesh V This Patch is related to "[U-Boot,4/5] devkit8000 nand_spl: Add SPL NAND support to omap_gpmc driver" (http://article.gmane.org/gmane.comp.boot-loaders.u-boot/102115) in V1 --- doc/README.SPL | 2 + drivers/mtd/nand/Makefile | 9 +++++- drivers/mtd/nand/omap_gpmc.c | 68 ++++++++++++++++++++++++++++++++++++++++++ spl/Makefile | 2 + 4 files changed, 80 insertions(+), 1 deletions(-)