[4/9] ARM: dts: sun9i: cubieboard4: Add GPIO pin-bank regulator supplies

Message ID 20190206033239.3619-5-wens@csie.org
State New
Headers show
Series
  • ARM: sun9i: a80: Enable GMAC
Related show

Commit Message

Chen-Yu Tsai Feb. 6, 2019, 3:32 a.m.
The Cubieboard 4 has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.

Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 23 ++++++++++++++++++---
 1 file changed, 20 insertions(+), 3 deletions(-)

Patch

diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 85da85faf869..0daab9b374e6 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -183,10 +183,26 @@ 
 	clocks = <&ac100_rtc 0>;
 };
 
+&pio {
+	vcc-pa-supply = <&reg_ldo_io1>;
+	vcc-pb-supply = <&reg_aldo2>;
+	vcc-pc-supply = <&reg_dcdc1>;
+	vcc-pd-supply = <&reg_dc1sw>;
+	vcc-pe-supply = <&reg_eldo2>;
+	vcc-pf-supply = <&reg_dcdc1>;
+	vcc-pg-supply = <&reg_ldo_io0>;
+	vcc-ph-supply = <&reg_dcdc1>;
+};
+
 &r_ir {
 	status = "okay";
 };
 
+&r_pio {
+	vcc-pl-supply = <&reg_dldo2>;
+	vcc-pm-supply = <&reg_eldo3>;
+};
+
 &r_rsb {
 	status = "okay";
 
@@ -217,6 +233,10 @@ 
 				/* unused */
 			};
 
+			reg_dc1sw: dc1sw {
+				regulator-name = "vcc-pd";
+			};
+
 			reg_dc5ldo: dc5ldo {
 				regulator-always-on;
 				regulator-min-microvolt = <800000>;
@@ -271,7 +291,6 @@ 
 			};
 
 			reg_dldo2: dldo2 {
-				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-name = "vcc-pl";
@@ -290,14 +309,12 @@ 
 			};
 
 			reg_eldo3: eldo3 {
-				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-name = "vcc-pm-codec-io1";
 			};
 
 			reg_ldo_io0: ldo_io0 {
-				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-name = "vcc-pg";