diff mbox series

drivers: net: atp: fix various indentation issues

Message ID 20190114153701.18203-1-colin.king@canonical.com
State Accepted
Delegated to: David Miller
Headers show
Series drivers: net: atp: fix various indentation issues | expand

Commit Message

Colin Ian King Jan. 14, 2019, 3:37 p.m. UTC 
From: Colin Ian King <colin.king@canonical.com>

There are various lines that have indentation issues, fix these.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
---
 drivers/net/ethernet/realtek/atp.c | 27 +++++++++++++++------------
 1 file changed, 15 insertions(+), 12 deletions(-)

Comments

David Miller Jan. 16, 2019, 10:04 p.m. UTC | #1 
From: Colin King <colin.king@canonical.com>
Date: Mon, 14 Jan 2019 15:37:01 +0000

> From: Colin Ian King <colin.king@canonical.com>
> 
> There are various lines that have indentation issues, fix these.
> 
> Signed-off-by: Colin Ian King <colin.king@canonical.com>

Applied.
diff mbox series

Patch

diff --git a/drivers/net/ethernet/realtek/atp.c b/drivers/net/ethernet/realtek/atp.c
index 7e011c1c1e6e..cfb67b746595 100644
--- a/drivers/net/ethernet/realtek/atp.c
+++ b/drivers/net/ethernet/realtek/atp.c
@@ -454,14 +454,14 @@  static void hardware_init(struct net_device *dev)
 {
 	struct net_local *lp = netdev_priv(dev);
 	long ioaddr = dev->base_addr;
-    int i;
+	int i;
 
 	/* Turn off the printer multiplexer on the 8012. */
 	for (i = 0; i < 8; i++)
 		outb(mux_8012[i], ioaddr + PAR_DATA);
 	write_reg_high(ioaddr, CMR1, CMR1h_RESET);
 
-    for (i = 0; i < 6; i++)
+	for (i = 0; i < 6; i++)
 		write_reg_byte(ioaddr, PAR0 + i, dev->dev_addr[i]);
 
 	write_reg_high(ioaddr, CMR2, lp->addr_mode);
@@ -471,15 +471,15 @@  static void hardware_init(struct net_device *dev)
 			   (read_nibble(ioaddr, CMR2_h) >> 3) & 0x0f);
 	}
 
-    write_reg(ioaddr, CMR2, CMR2_IRQOUT);
-    write_reg_high(ioaddr, CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE);
+	write_reg(ioaddr, CMR2, CMR2_IRQOUT);
+	write_reg_high(ioaddr, CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE);
 
 	/* Enable the interrupt line from the serial port. */
 	outb(Ctrl_SelData + Ctrl_IRQEN, ioaddr + PAR_CONTROL);
 
 	/* Unmask the interesting interrupts. */
-    write_reg(ioaddr, IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK);
-    write_reg_high(ioaddr, IMR, ISRh_RxErr);
+	write_reg(ioaddr, IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK);
+	write_reg_high(ioaddr, IMR, ISRh_RxErr);
 
 	lp->tx_unit_busy = 0;
     lp->pac_cnt_in_tx_buf = 0;
@@ -610,10 +610,12 @@  static irqreturn_t atp_interrupt(int irq, void *dev_instance)
 	write_reg(ioaddr, CMR2, CMR2_NULL);
 	write_reg(ioaddr, IMR, 0);
 
-	if (net_debug > 5) printk(KERN_DEBUG "%s: In interrupt ", dev->name);
-    while (--boguscount > 0) {
+	if (net_debug > 5)
+		printk(KERN_DEBUG "%s: In interrupt ", dev->name);
+	while (--boguscount > 0) {
 		int status = read_nibble(ioaddr, ISR);
-		if (net_debug > 5) printk("loop status %02x..", status);
+		if (net_debug > 5)
+			printk("loop status %02x..", status);
 
 		if (status & (ISR_RxOK<<3)) {
 			handled = 1;
@@ -640,7 +642,8 @@  static irqreturn_t atp_interrupt(int irq, void *dev_instance)
 			} while (--boguscount > 0);
 		} else if (status & ((ISR_TxErr + ISR_TxOK)<<3)) {
 			handled = 1;
-			if (net_debug > 6)  printk("handling Tx done..");
+			if (net_debug > 6)
+				printk("handling Tx done..");
 			/* Clear the Tx interrupt.  We should check for too many failures
 			   and reinitialize the adapter. */
 			write_reg(ioaddr, ISR, ISR_TxErr + ISR_TxOK);
@@ -680,7 +683,7 @@  static irqreturn_t atp_interrupt(int irq, void *dev_instance)
 			break;
 		} else
 			break;
-    }
+	}
 
 	/* This following code fixes a rare (and very difficult to track down)
 	   problem where the adapter forgets its ethernet address. */
@@ -694,7 +697,7 @@  static irqreturn_t atp_interrupt(int irq, void *dev_instance)
 	}
 
 	/* Tell the adapter that it can go back to using the output line as IRQ. */
-    write_reg(ioaddr, CMR2, CMR2_IRQOUT);
+	write_reg(ioaddr, CMR2, CMR2_IRQOUT);
 	/* Enable the physical interrupt line, which is sure to be low until.. */
 	outb(Ctrl_SelData + Ctrl_IRQEN, ioaddr + PAR_CONTROL);
 	/* .. we enable the interrupt sources. */