[U-Boot,1/2] ARM: dts: sun8i: Update A80 dts(i) from Linux-v4.18-rc3
diff mbox series

Message ID 20190111111549.6433-1-jagan@amarulasolutions.com
State Accepted
Commit 8dcc7e69224f898272dbbbba2d9a1c5efaa28304
Delegated to: Jagannadha Sutradharudu Teki
Headers show
Series
  • [U-Boot,1/2] ARM: dts: sun8i: Update A80 dts(i) from Linux-v4.18-rc3
Related show

Commit Message

Jagan Teki Jan. 11, 2019, 11:15 a.m. UTC
Update all A80 devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commits.

arch/arm/boot/dts/sun9i-a80*:

commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date:   Tue Mar 27 14:58:00 2018 +0200

    Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

include/dt-bindings/*/sun9i-a80-*:

commit 783ab76ae553abc23f80ef7511052d055697531b
Author: Chen-Yu Tsai <wens@csie.org>
Date:   Sat Jan 28 20:22:36 2017 +0800

    clk: sunxi-ng: Add A80 Display Engine CCU

Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
dts is not available in Linux.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
 arch/arm/dts/sun9i-a80-cubieboard4.dts    |  260 ++++-
 arch/arm/dts/sun9i-a80-cx-a99.dts         |    2 +-
 arch/arm/dts/sun9i-a80-optimus.dts        |  227 ++++-
 arch/arm/dts/sun9i-a80.dtsi               | 1062 +++++++++++++--------
 include/dt-bindings/clock/sun9i-a80-ccu.h |  162 ++++
 include/dt-bindings/clock/sun9i-a80-de.h  |   80 ++
 include/dt-bindings/clock/sun9i-a80-usb.h |   59 ++
 include/dt-bindings/reset/sun9i-a80-ccu.h |  102 ++
 include/dt-bindings/reset/sun9i-a80-de.h  |   58 ++
 include/dt-bindings/reset/sun9i-a80-usb.h |   56 ++
 10 files changed, 1597 insertions(+), 471 deletions(-)
 create mode 100644 include/dt-bindings/clock/sun9i-a80-ccu.h
 create mode 100644 include/dt-bindings/clock/sun9i-a80-de.h
 create mode 100644 include/dt-bindings/clock/sun9i-a80-usb.h
 create mode 100644 include/dt-bindings/reset/sun9i-a80-ccu.h
 create mode 100644 include/dt-bindings/reset/sun9i-a80-de.h
 create mode 100644 include/dt-bindings/reset/sun9i-a80-usb.h

Comments

Jagan Teki Jan. 11, 2019, 4:08 p.m. UTC | #1
Chen-Yu and Rask,

On Fri, Jan 11, 2019 at 4:46 PM Jagan Teki <jagan@amarulasolutions.com> wrote:
>
> Update all A80 devicetree dtsi and dtsi files from
> Linux-v4.18-rc3 with below commits.
>
> arch/arm/boot/dts/sun9i-a80*:
>
> commit 190e3138f9577885691540dca59c2f07540bde04
> Merge: cafc87023b0d a7affb13b271
> Author: Arnd Bergmann <arnd@arndb.de>
> Date:   Tue Mar 27 14:58:00 2018 +0200
>
>     Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
>
> include/dt-bindings/*/sun9i-a80-*:
>
> commit 783ab76ae553abc23f80ef7511052d055697531b
> Author: Chen-Yu Tsai <wens@csie.org>
> Date:   Sat Jan 28 20:22:36 2017 +0800
>
>     clk: sunxi-ng: Add A80 Display Engine CCU
>
> Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
> dts is not available in Linux.
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
>  arch/arm/dts/sun9i-a80-cubieboard4.dts    |  260 ++++-
>  arch/arm/dts/sun9i-a80-cx-a99.dts         |    2 +-
>  arch/arm/dts/sun9i-a80-optimus.dts        |  227 ++++-
>  arch/arm/dts/sun9i-a80.dtsi               | 1062 +++++++++++++--------
>  include/dt-bindings/clock/sun9i-a80-ccu.h |  162 ++++
>  include/dt-bindings/clock/sun9i-a80-de.h  |   80 ++
>  include/dt-bindings/clock/sun9i-a80-usb.h |   59 ++
>  include/dt-bindings/reset/sun9i-a80-ccu.h |  102 ++
>  include/dt-bindings/reset/sun9i-a80-de.h  |   58 ++
>  include/dt-bindings/reset/sun9i-a80-usb.h |   56 ++
>  10 files changed, 1597 insertions(+), 471 deletions(-)
>  create mode 100644 include/dt-bindings/clock/sun9i-a80-ccu.h
>  create mode 100644 include/dt-bindings/clock/sun9i-a80-de.h
>  create mode 100644 include/dt-bindings/clock/sun9i-a80-usb.h
>  create mode 100644 include/dt-bindings/reset/sun9i-a80-ccu.h
>  create mode 100644 include/dt-bindings/reset/sun9i-a80-de.h
>  create mode 100644 include/dt-bindings/reset/sun9i-a80-usb.h

Can you check this sync on your A80 boards?
Chen-Yu Tsai Jan. 14, 2019, 8:42 a.m. UTC | #2
On Sat, Jan 12, 2019 at 12:08 AM Jagan Teki <jagan@amarulasolutions.com> wrote:
>
> Chen-Yu and Rask,
>
> On Fri, Jan 11, 2019 at 4:46 PM Jagan Teki <jagan@amarulasolutions.com> wrote:
> >
> > Update all A80 devicetree dtsi and dtsi files from
> > Linux-v4.18-rc3 with below commits.
> >
> > arch/arm/boot/dts/sun9i-a80*:
> >
> > commit 190e3138f9577885691540dca59c2f07540bde04
> > Merge: cafc87023b0d a7affb13b271
> > Author: Arnd Bergmann <arnd@arndb.de>
> > Date:   Tue Mar 27 14:58:00 2018 +0200
> >
> >     Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
> >
> > include/dt-bindings/*/sun9i-a80-*:
> >
> > commit 783ab76ae553abc23f80ef7511052d055697531b
> > Author: Chen-Yu Tsai <wens@csie.org>
> > Date:   Sat Jan 28 20:22:36 2017 +0800
> >
> >     clk: sunxi-ng: Add A80 Display Engine CCU
> >
> > Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
> > dts is not available in Linux.
> >
> > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > ---
> >  arch/arm/dts/sun9i-a80-cubieboard4.dts    |  260 ++++-
> >  arch/arm/dts/sun9i-a80-cx-a99.dts         |    2 +-
> >  arch/arm/dts/sun9i-a80-optimus.dts        |  227 ++++-
> >  arch/arm/dts/sun9i-a80.dtsi               | 1062 +++++++++++++--------
> >  include/dt-bindings/clock/sun9i-a80-ccu.h |  162 ++++
> >  include/dt-bindings/clock/sun9i-a80-de.h  |   80 ++
> >  include/dt-bindings/clock/sun9i-a80-usb.h |   59 ++
> >  include/dt-bindings/reset/sun9i-a80-ccu.h |  102 ++
> >  include/dt-bindings/reset/sun9i-a80-de.h  |   58 ++
> >  include/dt-bindings/reset/sun9i-a80-usb.h |   56 ++
> >  10 files changed, 1597 insertions(+), 471 deletions(-)
> >  create mode 100644 include/dt-bindings/clock/sun9i-a80-ccu.h
> >  create mode 100644 include/dt-bindings/clock/sun9i-a80-de.h
> >  create mode 100644 include/dt-bindings/clock/sun9i-a80-usb.h
> >  create mode 100644 include/dt-bindings/reset/sun9i-a80-ccu.h
> >  create mode 100644 include/dt-bindings/reset/sun9i-a80-de.h
> >  create mode 100644 include/dt-bindings/reset/sun9i-a80-usb.h
>
> Can you check this sync on your A80 boards?

Tried sunxi/next on the A80 Optimus, and it correctly boots to Linux.
That's all I can say though.

ChenYu
Jagan Teki Jan. 18, 2019, 4:52 p.m. UTC | #3
On Fri, Jan 11, 2019 at 4:46 PM Jagan Teki <jagan@amarulasolutions.com> wrote:
>
> Update all A80 devicetree dtsi and dtsi files from
> Linux-v4.18-rc3 with below commits.
>
> arch/arm/boot/dts/sun9i-a80*:
>
> commit 190e3138f9577885691540dca59c2f07540bde04
> Merge: cafc87023b0d a7affb13b271
> Author: Arnd Bergmann <arnd@arndb.de>
> Date:   Tue Mar 27 14:58:00 2018 +0200
>
>     Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
>
> include/dt-bindings/*/sun9i-a80-*:
>
> commit 783ab76ae553abc23f80ef7511052d055697531b
> Author: Chen-Yu Tsai <wens@csie.org>
> Date:   Sat Jan 28 20:22:36 2017 +0800
>
>     clk: sunxi-ng: Add A80 Display Engine CCU
>
> Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
> dts is not available in Linux.
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---

Applied both to u-boot-sunxi/master
Rask Ingemann Lambertsen Jan. 19, 2019, 2:43 p.m. UTC | #4
Den 11-01-2019 kl. 16:45 +0530 skrev Jagan Teki:
> Update all A80 devicetree dtsi and dtsi files from
> Linux-v4.18-rc3 with below commits.
> 
> arch/arm/boot/dts/sun9i-a80*:
> 
> commit 190e3138f9577885691540dca59c2f07540bde04
> Merge: cafc87023b0d a7affb13b271
> Author: Arnd Bergmann <arnd@arndb.de>
> Date:   Tue Mar 27 14:58:00 2018 +0200
> 
>     Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
> 
> include/dt-bindings/*/sun9i-a80-*:
> 
> commit 783ab76ae553abc23f80ef7511052d055697531b
> Author: Chen-Yu Tsai <wens@csie.org>
> Date:   Sat Jan 28 20:22:36 2017 +0800
> 
>     clk: sunxi-ng: Add A80 Display Engine CCU
> 
> Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
> dts is not available in Linux.
> 
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---

It boots Linux from eMMC on a CX-A99 board just as well as it did before.

Patch
diff mbox series

diff --git a/arch/arm/dts/sun9i-a80-cubieboard4.dts b/arch/arm/dts/sun9i-a80-cubieboard4.dts
index 1526b41c70..85da85faf8 100644
--- a/arch/arm/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/dts/sun9i-a80-cubieboard4.dts
@@ -47,7 +47,6 @@ 
 #include "sun9i-a80.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Cubietech Cubieboard4";
@@ -63,8 +62,6 @@ 
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_cubieboard4>;
 
 		green {
 			label = "cubieboard4:green:usr";
@@ -76,18 +73,96 @@ 
 			gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
 		};
 	};
+
+	vga-connector {
+		compatible = "vga-connector";
+		label = "vga";
+		ddc-i2c-bus = <&i2c3>;
+
+		port {
+			vga_con_in: endpoint {
+				remote-endpoint = <&vga_dac_out>;
+			};
+		};
+	};
+
+	vga-dac {
+		compatible = "corpro,gm7123", "adi,adv7123", "dumb-vga-dac";
+		vdd-supply = <&reg_dcdc1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				vga_dac_in: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&tcon0_out_vga>;
+				};
+			};
+
+			port@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+
+				vga_dac_out: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&vga_con_in>;
+				};
+			};
+		};
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&ac100_rtc 1>;
+		clock-names = "ext_clock";
+		/* enables internal regulator and de-asserts reset */
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+	};
+};
+
+&de {
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+	status = "okay";
 };
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
+	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
-	cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
-	cd-inverted;
+	cd-gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; /* PH18 */
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_dldo1>;
+	vqmmc-supply = <&reg_cldo3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
 	status = "okay";
 };
 
+&mmc1_pins {
+	bias-pull-up;
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
@@ -100,23 +175,12 @@ 
 
 &mmc2_8bit_pins {
 	/* Increase drive strength for DDR modes */
-	allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+	drive-strength = <40>;
 };
 
-&pio {
-	led_pins_cubieboard4: led-pins@0 {
-		allwinner,pins = "PH6", "PH17";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
-		allwinner,pins = "PH18";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-	};
+&osc32k {
+	/* osc32k input is from AC100 */
+	clocks = <&ac100_rtc 0>;
 };
 
 &r_ir {
@@ -248,14 +312,166 @@ 
 			reg_rtc_ldo: rtc_ldo {
 				regulator-name = "vcc-rtc-vdd1v8-io";
 			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+
+	axp806: pmic@745 {
+		compatible = "x-powers,axp806";
+		reg = <0x745>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		bldoin-supply = <&reg_dcdce>;
+
+		regulators {
+			reg_s_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "avcc";
+			};
+
+			aldo2 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo2";
+			};
+
+			aldo3 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo3";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name = "vcc18-efuse-adc-display-csi";
+			};
+
+			reg_bldo2: bldo2 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name =
+					"vdd18-drampll-vcc18-pll-cpvdd";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			reg_bldo4: bldo4 {
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-name = "vcc12-hsic";
+			};
+
+			reg_cldo1: cldo1 {
+				/*
+				 * This was 3V in the original design, but
+				 * 3.3V is the recommended supply voltage
+				 * for the Ethernet PHY.
+				 */
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-gmac-phy";
+			};
+
+			reg_cldo2: cldo2 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-name = "afvcc-cam";
+			};
+
+			reg_cldo3: cldo3 {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-io-wifi-codec-io2";
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpub";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-vpu";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <2100000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-name = "vcc-bldo-codec-ldoin";
+			};
+
+			sw {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's sw
+				 */
+				regulator-name = "s_sw";
+			};
+		};
+	};
+
+	ac100: codec@e89 {
+		compatible = "x-powers,ac100";
+		reg = <0xe89>;
+
+		ac100_codec: codec {
+			compatible = "x-powers,ac100-codec";
+			interrupt-parent = <&r_pio>;
+			interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */
+			#clock-cells = <0>;
+			clock-output-names = "4M_adda";
+		};
+
+		ac100_rtc: rtc {
+			compatible = "x-powers,ac100-rtc";
+			interrupt-parent = <&nmi_intc>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&ac100_codec>;
+			#clock-cells = <1>;
+			clock-output-names = "cko1_rtc",
+					     "cko2_rtc",
+					     "cko3_rtc";
 		};
 	};
 };
 
 #include "axp809.dtsi"
 
+&tcon0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd0_rgb888_pins>;
+};
+
+&tcon0_out {
+	tcon0_out_vga: endpoint@0 {
+		reg = <0>;
+		remote-endpoint = <&vga_dac_in>;
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
diff --git a/arch/arm/dts/sun9i-a80-cx-a99.dts b/arch/arm/dts/sun9i-a80-cx-a99.dts
index a30b6fec56..cf126bbd2c 100644
--- a/arch/arm/dts/sun9i-a80-cx-a99.dts
+++ b/arch/arm/dts/sun9i-a80-cx-a99.dts
@@ -365,7 +365,7 @@ 
  */
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun9i-a80-optimus.dts b/arch/arm/dts/sun9i-a80-optimus.dts
index 7fd22e8886..58a199b0e4 100644
--- a/arch/arm/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/dts/sun9i-a80-optimus.dts
@@ -46,7 +46,6 @@ 
 #include "sun9i-a80.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Merrii A80 Optimus Board";
@@ -63,11 +62,8 @@ 
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_optimus>, <&led_r_pins_optimus>;
 
 		/* The LED names match those found on the board */
-
 		led2 {
 			label = "optimus:led2:usr";
 			gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>;
@@ -87,8 +83,6 @@ 
 	reg_usb1_vbus: usb1-vbus {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
-		pinctrl-0 = <&usb1_vbus_pin_optimus>;
-		regulator-name = "usb1-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
@@ -98,13 +92,19 @@ 
 	reg_usb3_vbus: usb3-vbus {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
-		pinctrl-0 = <&usb3_vbus_pin_optimus>;
-		regulator-name = "usb3-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
 		gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
 	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&ac100_rtc 1>;
+		clock-names = "ext_clock";
+		/* enables internal regulator and de-asserts reset */
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+	};
 };
 
 &ehci0 {
@@ -112,7 +112,8 @@ 
 };
 
 &ehci1 {
-	status = "okay";
+	/* Enable if HSIC peripheral is connected */
+	status = "disabled";
 };
 
 &ehci2 {
@@ -121,14 +122,28 @@ 
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
+	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
-	cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
-	cd-inverted;
+	cd-gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; /* PH8 */
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_dldo1>;
+	vqmmc-supply = <&reg_cldo3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
 	status = "okay";
 };
 
+&mmc1_pins {
+	bias-pull-up;
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
@@ -141,7 +156,7 @@ 
 
 &mmc2_8bit_pins {
 	/* Increase drive strength for DDR modes */
-	allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+	drive-strength = <40>;
 };
 
 &ohci0 {
@@ -152,49 +167,15 @@ 
 	status = "okay";
 };
 
-&pio {
-	led_pins_optimus: led-pins@0 {
-		allwinner,pins = "PH0", "PH1";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	mmc0_cd_pin_optimus: mmc0_cd_pin@0 {
-		allwinner,pins = "PH18";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-	};
-
-	usb1_vbus_pin_optimus: usb1_vbus_pin@1 {
-		allwinner,pins = "PH4";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	usb3_vbus_pin_optimus: usb3_vbus_pin@1 {
-		allwinner,pins = "PH5";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
+&osc32k {
+	/* osc32k input is from AC100 */
+	clocks = <&ac100_rtc 0>;
 };
 
 &r_ir {
 	status = "okay";
 };
 
-&r_pio {
-	led_r_pins_optimus: led-pins@1 {
-		allwinner,pins = "PM15";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-};
-
 &r_rsb {
 	status = "okay";
 
@@ -320,6 +301,146 @@ 
 			reg_rtc_ldo: rtc_ldo {
 				regulator-name = "vcc-rtc-vdd1v8-io";
 			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+
+	axp806: pmic@745 {
+		compatible = "x-powers,axp806";
+		reg = <0x745>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		bldoin-supply = <&reg_dcdce>;
+
+		regulators {
+			reg_s_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "avcc";
+			};
+
+			aldo2 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo2";
+			};
+
+			aldo3 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo3";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name = "vcc18-efuse-adc-display-csi";
+			};
+
+			reg_bldo2: bldo2 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name =
+					"vdd18-drampll-vcc18-pll-cpvdd";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			reg_bldo4: bldo4 {
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-name = "vcc12-hsic";
+			};
+
+			reg_cldo1: cldo1 {
+				/*
+				 * This was 3V in the original design, but
+				 * 3.3V is the recommended supply voltage
+				 * for the Ethernet PHY.
+				 */
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-gmac-phy";
+			};
+
+			reg_cldo2: cldo2 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-name = "afvcc-cam";
+			};
+
+			reg_cldo3: cldo3 {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-io-wifi-codec-io2";
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpub";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-vpu";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <2100000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-name = "vcc-bldo-codec-ldoin";
+			};
+
+			sw {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's sw
+				 */
+				regulator-name = "s_sw";
+			};
+		};
+	};
+
+	ac100: codec@e89 {
+		compatible = "x-powers,ac100";
+		reg = <0xe89>;
+
+		ac100_codec: codec {
+			compatible = "x-powers,ac100-codec";
+			interrupt-parent = <&r_pio>;
+			interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */
+			#clock-cells = <0>;
+			clock-output-names = "4M_adda";
+		};
+
+		ac100_rtc: rtc {
+			compatible = "x-powers,ac100-rtc";
+			interrupt-parent = <&nmi_intc>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&ac100_codec>;
+			#clock-cells = <1>;
+			clock-output-names = "cko1_rtc",
+					     "cko2_rtc",
+					     "cko3_rtc";
 		};
 	};
 };
@@ -328,7 +449,7 @@ 
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };
 
@@ -338,7 +459,9 @@ 
 };
 
 &usbphy2 {
-	status = "okay";
+	phy-supply = <&reg_bldo4>;
+	/* Enable if HSIC peripheral is connected */
+	status = "disabled";
 };
 
 &usbphy3 {
diff --git a/arch/arm/dts/sun9i-a80.dtsi b/arch/arm/dts/sun9i-a80.dtsi
index 92412b2ac1..25591d6883 100644
--- a/arch/arm/dts/sun9i-a80.dtsi
+++ b/arch/arm/dts/sun9i-a80.dtsi
@@ -42,13 +42,18 @@ 
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "skeleton64.dtsi"
-
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/clock/sun9i-a80-ccu.h>
+#include <dt-bindings/clock/sun9i-a80-de.h>
+#include <dt-bindings/clock/sun9i-a80-usb.h>
+#include <dt-bindings/reset/sun9i-a80-ccu.h>
+#include <dt-bindings/reset/sun9i-a80-de.h>
+#include <dt-bindings/reset/sun9i-a80-usb.h>
 
 / {
+	#address-cells = <2>;
+	#size-cells = <2>;
 	interrupt-parent = <&gic>;
 
 	cpus {
@@ -58,57 +63,76 @@ 
 		cpu0: cpu@0 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
+			cci-control-port = <&cci_control0>;
+			clock-frequency = <12000000>;
+			enable-method = "allwinner,sun9i-a80-smp";
 			reg = <0x0>;
 		};
 
 		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
+			cci-control-port = <&cci_control0>;
+			clock-frequency = <12000000>;
+			enable-method = "allwinner,sun9i-a80-smp";
 			reg = <0x1>;
 		};
 
 		cpu2: cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
+			cci-control-port = <&cci_control0>;
+			clock-frequency = <12000000>;
+			enable-method = "allwinner,sun9i-a80-smp";
 			reg = <0x2>;
 		};
 
 		cpu3: cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
+			cci-control-port = <&cci_control0>;
+			clock-frequency = <12000000>;
+			enable-method = "allwinner,sun9i-a80-smp";
 			reg = <0x3>;
 		};
 
 		cpu4: cpu@100 {
 			compatible = "arm,cortex-a15";
 			device_type = "cpu";
+			cci-control-port = <&cci_control1>;
+			clock-frequency = <18000000>;
+			enable-method = "allwinner,sun9i-a80-smp";
 			reg = <0x100>;
 		};
 
 		cpu5: cpu@101 {
 			compatible = "arm,cortex-a15";
 			device_type = "cpu";
+			cci-control-port = <&cci_control1>;
+			clock-frequency = <18000000>;
+			enable-method = "allwinner,sun9i-a80-smp";
 			reg = <0x101>;
 		};
 
 		cpu6: cpu@102 {
 			compatible = "arm,cortex-a15";
 			device_type = "cpu";
+			cci-control-port = <&cci_control1>;
+			clock-frequency = <18000000>;
+			enable-method = "allwinner,sun9i-a80-smp";
 			reg = <0x102>;
 		};
 
 		cpu7: cpu@103 {
 			compatible = "arm,cortex-a15";
 			device_type = "cpu";
+			cci-control-port = <&cci_control1>;
+			clock-frequency = <18000000>;
+			enable-method = "allwinner,sun9i-a80-smp";
 			reg = <0x103>;
 		};
 	};
 
-	memory {
-		/* 8GB max. with LPAE */
-		reg = <0 0x20000000 0x02 0>;
-	};
-
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -139,7 +163,7 @@ 
 		 * would also throw all the PLL clock rates off, or just the
 		 * downstream clocks in the PRCM.
 		 */
-		osc24M: osc24M_clk {
+		osc24M: clk-24M {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
@@ -148,244 +172,28 @@ 
 
 		/*
 		 * The 32k clock is from an external source, normally the
-		 * AC100 codec/RTC chip. This clock is by default enabled
-		 * and clocked at 32768 Hz, from the oscillator connected
-		 * to the AC100. It is configurable, but no such driver or
-		 * bindings exist yet.
+		 * AC100 codec/RTC chip. This serves as a placeholder for
+		 * board dts files to specify the source.
 		 */
-		osc32k: osc32k_clk {
+		osc32k: clk-32k {
 			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
+			compatible = "fixed-factor-clock";
+			clock-div = <1>;
+			clock-mult = <1>;
 			clock-output-names = "osc32k";
 		};
 
-		usb_mod_clk: clk@00a08000 {
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			compatible = "allwinner,sun9i-a80-usb-mod-clk";
-			reg = <0x00a08000 0x4>;
-			clocks = <&ahb1_gates 1>;
-			clock-output-names = "usb0_ahb", "usb_ohci0",
-					     "usb1_ahb", "usb_ohci1",
-					     "usb2_ahb", "usb_ohci2";
-		};
-
-		usb_phy_clk: clk@00a08004 {
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			compatible = "allwinner,sun9i-a80-usb-phy-clk";
-			reg = <0x00a08004 0x4>;
-			clocks = <&ahb1_gates 1>;
-			clock-output-names = "usb_phy0", "usb_hsic1_480M",
-					     "usb_phy1", "usb_hsic2_480M",
-					     "usb_phy2", "usb_hsic_12M";
-		};
-
-		pll3: clk@06000008 {
-			/* placeholder until implemented */
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-rate = <0>;
-			clock-output-names = "pll3";
-		};
-
-		pll4: clk@0600000c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun9i-a80-pll4-clk";
-			reg = <0x0600000c 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll4";
-		};
-
-		pll12: clk@0600002c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun9i-a80-pll4-clk";
-			reg = <0x0600002c 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll12";
-		};
-
-		gt_clk: clk@0600005c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun9i-a80-gt-clk";
-			reg = <0x0600005c 0x4>;
-			clocks = <&osc24M>, <&pll4>, <&pll12>, <&pll12>;
-			clock-output-names = "gt";
-		};
-
-		ahb0: clk@06000060 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun9i-a80-ahb-clk";
-			reg = <0x06000060 0x4>;
-			clocks = <&gt_clk>, <&pll4>, <&pll12>, <&pll12>;
-			clock-output-names = "ahb0";
-		};
-
-		ahb1: clk@06000064 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun9i-a80-ahb-clk";
-			reg = <0x06000064 0x4>;
-			clocks = <&gt_clk>, <&pll4>, <&pll12>, <&pll12>;
-			clock-output-names = "ahb1";
-		};
-
-		ahb2: clk@06000068 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun9i-a80-ahb-clk";
-			reg = <0x06000068 0x4>;
-			clocks = <&gt_clk>, <&pll4>, <&pll12>, <&pll12>;
-			clock-output-names = "ahb2";
-		};
-
-		apb0: clk@06000070 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun9i-a80-apb0-clk";
-			reg = <0x06000070 0x4>;
-			clocks = <&osc24M>, <&pll4>;
-			clock-output-names = "apb0";
-		};
-
-		apb1: clk@06000074 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun9i-a80-apb1-clk";
-			reg = <0x06000074 0x4>;
-			clocks = <&osc24M>, <&pll4>;
-			clock-output-names = "apb1";
-		};
-
-		cci400_clk: clk@06000078 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun9i-a80-gt-clk";
-			reg = <0x06000078 0x4>;
-			clocks = <&osc24M>, <&pll4>, <&pll12>, <&pll12>;
-			clock-output-names = "cci400";
-		};
-
-		mmc0_clk: clk@06000410 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun9i-a80-mmc-clk";
-			reg = <0x06000410 0x4>;
-			clocks = <&osc24M>, <&pll4>;
-			clock-output-names = "mmc0", "mmc0_output",
-					     "mmc0_sample";
-		};
-
-		mmc1_clk: clk@06000414 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun9i-a80-mmc-clk";
-			reg = <0x06000414 0x4>;
-			clocks = <&osc24M>, <&pll4>;
-			clock-output-names = "mmc1", "mmc1_output",
-					     "mmc1_sample";
-		};
-
-		mmc2_clk: clk@06000418 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun9i-a80-mmc-clk";
-			reg = <0x06000418 0x4>;
-			clocks = <&osc24M>, <&pll4>;
-			clock-output-names = "mmc2", "mmc2_output",
-					     "mmc2_sample";
-		};
-
-		mmc3_clk: clk@0600041c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun9i-a80-mmc-clk";
-			reg = <0x0600041c 0x4>;
-			clocks = <&osc24M>, <&pll4>;
-			clock-output-names = "mmc3", "mmc3_output",
-					     "mmc3_sample";
-		};
-
-		ahb0_gates: clk@06000580 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun9i-a80-ahb0-gates-clk";
-			reg = <0x06000580 0x4>;
-			clocks = <&ahb0>;
-			clock-indices = <0>, <1>, <3>,
-					<5>, <8>, <12>,
-					<13>, <14>,
-					<15>, <16>, <18>,
-					<20>, <21>, <22>,
-					<23>;
-			clock-output-names = "ahb0_fd", "ahb0_ve", "ahb0_gpu",
-					"ahb0_ss", "ahb0_sd", "ahb0_nand1",
-					"ahb0_nand0", "ahb0_sdram",
-					"ahb0_mipi_hsi", "ahb0_sata", "ahb0_ts",
-					"ahb0_spi0", "ahb0_spi1", "ahb0_spi2",
-					"ahb0_spi3";
-		};
-
-		ahb1_gates: clk@06000584 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun9i-a80-ahb1-gates-clk";
-			reg = <0x06000584 0x4>;
-			clocks = <&ahb1>;
-			clock-indices = <0>, <1>,
-					<17>, <21>,
-					<22>, <23>,
-					<24>;
-			clock-output-names = "ahb1_usbotg", "ahb1_usbhci",
-					"ahb1_gmac", "ahb1_msgbox",
-					"ahb1_spinlock", "ahb1_hstimer",
-					"ahb1_dma";
-		};
-
-		ahb2_gates: clk@06000588 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun9i-a80-ahb2-gates-clk";
-			reg = <0x06000588 0x4>;
-			clocks = <&ahb2>;
-			clock-indices = <0>, <1>,
-					<2>, <4>, <5>,
-					<7>, <8>, <11>;
-			clock-output-names = "ahb2_lcd0", "ahb2_lcd1",
-					"ahb2_edp", "ahb2_csi", "ahb2_hdmi",
-					"ahb2_de", "ahb2_mp", "ahb2_mipi_dsi";
-		};
-
-		apb0_gates: clk@06000590 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun9i-a80-apb0-gates-clk";
-			reg = <0x06000590 0x4>;
-			clocks = <&apb0>;
-			clock-indices = <1>, <5>,
-					<11>, <12>, <13>,
-					<15>, <17>, <18>,
-					<19>;
-			clock-output-names = "apb0_spdif", "apb0_pio",
-					"apb0_ac97", "apb0_i2s0", "apb0_i2s1",
-					"apb0_lradc", "apb0_gpadc", "apb0_twd",
-					"apb0_cirtx";
-		};
-
-		apb1_gates: clk@06000594 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun9i-a80-apb1-gates-clk";
-			reg = <0x06000594 0x4>;
-			clocks = <&apb1>;
-			clock-indices = <0>, <1>,
-					<2>, <3>, <4>,
-					<16>, <17>,
-					<18>, <19>,
-					<20>, <21>;
-			clock-output-names = "apb1_i2c0", "apb1_i2c1",
-					"apb1_i2c2", "apb1_i2c3", "apb1_i2c4",
-					"apb1_uart0", "apb1_uart1",
-					"apb1_uart2", "apb1_uart3",
-					"apb1_uart4", "apb1_uart5";
-		};
-
-		cpus_clk: clk@08001410 {
+		cpus_clk: clk@8001410 {
 			compatible = "allwinner,sun9i-a80-cpus-clk";
 			reg = <0x08001410 0x4>;
 			#clock-cells = <0>;
-			clocks = <&osc32k>, <&osc24M>, <&pll4>, <&pll3>;
+			clocks = <&osc32k>, <&osc24M>,
+				 <&ccu CLK_PLL_PERIPH0>,
+				 <&ccu CLK_PLL_AUDIO>;
 			clock-output-names = "cpus";
 		};
 
-		ahbs: ahbs_clk {
+		ahbs: clk-ahbs {
 			compatible = "fixed-factor-clock";
 			#clock-cells = <0>;
 			clock-div = <1>;
@@ -394,7 +202,7 @@ 
 			clock-output-names = "ahbs";
 		};
 
-		apbs: clk@0800141c {
+		apbs: clk@800141c {
 			compatible = "allwinner,sun8i-a23-apb0-clk";
 			reg = <0x0800141c 0x4>;
 			#clock-cells = <0>;
@@ -402,7 +210,7 @@ 
 			clock-output-names = "apbs";
 		};
 
-		apbs_gates: clk@08001428 {
+		apbs_gates: clk@8001428 {
 			compatible = "allwinner,sun9i-a80-apbs-gates-clk";
 			reg = <0x08001428 0x4>;
 			#clock-cells = <1>;
@@ -423,7 +231,7 @@ 
 					"apbs_i2s1", "apbs_twd";
 		};
 
-		r_1wire_clk: clk@08001450 {
+		r_1wire_clk: clk@8001450 {
 			reg = <0x08001450 0x4>;
 			#clock-cells = <0>;
 			compatible = "allwinner,sun4i-a10-mod0-clk";
@@ -431,7 +239,7 @@ 
 			clock-output-names = "r_1wire";
 		};
 
-		r_ir_clk: clk@08001454 {
+		r_ir_clk: clk@8001454 {
 			reg = <0x08001454 0x4>;
 			#clock-cells = <0>;
 			compatible = "allwinner,sun4i-a10-mod0-clk";
@@ -440,6 +248,12 @@ 
 		};
 	};
 
+	de: display-engine {
+		compatible = "allwinner,sun9i-a80-display-engine";
+		allwinner,pipelines = <&fe0>, <&fe1>;
+		status = "disabled";
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -450,103 +264,149 @@ 
 		 */
 		ranges = <0 0 0 0x20000000>;
 
-		ehci0: usb@00a00000 {
+		sram_b: sram@20000 {
+			/* 256 KiB secure SRAM at 0x20000 */
+			compatible = "mmio-sram";
+			reg = <0x00020000 0x40000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x00020000 0x40000>;
+
+			smp-sram@1000 {
+				/*
+				 * This is checked by BROM to determine if
+				 * cpu0 should jump to SMP entry vector
+				 */
+				compatible = "allwinner,sun9i-a80-smp-sram";
+				reg = <0x1000 0x8>;
+			};
+		};
+
+		ehci0: usb@a00000 {
 			compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
 			reg = <0x00a00000 0x100>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&usb_mod_clk 1>;
-			resets = <&usb_mod_clk 17>;
+			clocks = <&usb_clocks CLK_BUS_HCI0>;
+			resets = <&usb_clocks RST_USB0_HCI>;
 			phys = <&usbphy1>;
 			phy-names = "usb";
 			status = "disabled";
 		};
 
-		ohci0: usb@00a00400 {
+		ohci0: usb@a00400 {
 			compatible = "allwinner,sun9i-a80-ohci", "generic-ohci";
 			reg = <0x00a00400 0x100>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&usb_mod_clk 1>, <&usb_mod_clk 2>;
-			resets = <&usb_mod_clk 17>;
+			clocks = <&usb_clocks CLK_BUS_HCI0>,
+				 <&usb_clocks CLK_USB_OHCI0>;
+			resets = <&usb_clocks RST_USB0_HCI>;
 			phys = <&usbphy1>;
 			phy-names = "usb";
 			status = "disabled";
 		};
 
-		usbphy1: phy@00a00800 {
+		usbphy1: phy@a00800 {
 			compatible = "allwinner,sun9i-a80-usb-phy";
 			reg = <0x00a00800 0x4>;
-			clocks = <&usb_phy_clk 1>;
+			clocks = <&usb_clocks CLK_USB0_PHY>;
 			clock-names = "phy";
-			resets = <&usb_phy_clk 17>;
+			resets = <&usb_clocks RST_USB0_PHY>;
 			reset-names = "phy";
 			status = "disabled";
 			#phy-cells = <0>;
 		};
 
-		ehci1: usb@00a01000 {
+		ehci1: usb@a01000 {
 			compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
 			reg = <0x00a01000 0x100>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&usb_mod_clk 3>;
-			resets = <&usb_mod_clk 18>;
+			clocks = <&usb_clocks CLK_BUS_HCI1>;
+			resets = <&usb_clocks RST_USB1_HCI>;
 			phys = <&usbphy2>;
 			phy-names = "usb";
 			status = "disabled";
 		};
 
-		usbphy2: phy@00a01800 {
+		usbphy2: phy@a01800 {
 			compatible = "allwinner,sun9i-a80-usb-phy";
 			reg = <0x00a01800 0x4>;
-			clocks = <&usb_phy_clk 2>, <&usb_phy_clk 10>,
-				 <&usb_phy_clk 3>;
-			clock-names = "hsic_480M", "hsic_12M", "phy";
-			resets = <&usb_phy_clk 18>, <&usb_phy_clk 19>;
-			reset-names = "hsic", "phy";
+			clocks = <&usb_clocks CLK_USB1_HSIC>,
+				 <&usb_clocks CLK_USB_HSIC>,
+				 <&usb_clocks CLK_USB1_PHY>;
+			clock-names = "hsic_480M",
+				      "hsic_12M",
+				      "phy";
+			resets = <&usb_clocks RST_USB1_HSIC>,
+				 <&usb_clocks RST_USB1_PHY>;
+			reset-names = "hsic",
+				      "phy";
 			status = "disabled";
 			#phy-cells = <0>;
 			/* usb1 is always used with HSIC */
 			phy_type = "hsic";
 		};
 
-		ehci2: usb@00a02000 {
+		ehci2: usb@a02000 {
 			compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
 			reg = <0x00a02000 0x100>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&usb_mod_clk 5>;
-			resets = <&usb_mod_clk 19>;
+			clocks = <&usb_clocks CLK_BUS_HCI2>;
+			resets = <&usb_clocks RST_USB2_HCI>;
 			phys = <&usbphy3>;
 			phy-names = "usb";
 			status = "disabled";
 		};
 
-		ohci2: usb@00a02400 {
+		ohci2: usb@a02400 {
 			compatible = "allwinner,sun9i-a80-ohci", "generic-ohci";
 			reg = <0x00a02400 0x100>;
 			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&usb_mod_clk 5>, <&usb_mod_clk 6>;
-			resets = <&usb_mod_clk 19>;
+			clocks = <&usb_clocks CLK_BUS_HCI2>,
+				 <&usb_clocks CLK_USB_OHCI2>;
+			resets = <&usb_clocks RST_USB2_HCI>;
 			phys = <&usbphy3>;
 			phy-names = "usb";
 			status = "disabled";
 		};
 
-		usbphy3: phy@00a02800 {
+		usbphy3: phy@a02800 {
 			compatible = "allwinner,sun9i-a80-usb-phy";
 			reg = <0x00a02800 0x4>;
-			clocks = <&usb_phy_clk 4>, <&usb_phy_clk 10>,
-				 <&usb_phy_clk 5>;
-			clock-names = "hsic_480M", "hsic_12M", "phy";
-			resets = <&usb_phy_clk 20>, <&usb_phy_clk 21>;
-			reset-names = "hsic", "phy";
+			clocks = <&usb_clocks CLK_USB2_HSIC>,
+				 <&usb_clocks CLK_USB_HSIC>,
+				 <&usb_clocks CLK_USB2_PHY>;
+			clock-names = "hsic_480M",
+				      "hsic_12M",
+				      "phy";
+			resets = <&usb_clocks RST_USB2_HSIC>,
+				 <&usb_clocks RST_USB2_PHY>;
+			reset-names = "hsic",
+				      "phy";
 			status = "disabled";
 			#phy-cells = <0>;
 		};
 
-		mmc0: mmc@01c0f000 {
+		usb_clocks: clock@a08000 {
+			compatible = "allwinner,sun9i-a80-usb-clks";
+			reg = <0x00a08000 0x8>;
+			clocks = <&ccu CLK_BUS_USB>, <&osc24M>;
+			clock-names = "bus", "hosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		cpucfg@1700000 {
+			compatible = "allwinner,sun9i-a80-cpucfg";
+			reg = <0x01700000 0x100>;
+		};
+
+		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun9i-a80-mmc";
 			reg = <0x01c0f000 0x1000>;
-			clocks = <&mmc_config_clk 0>, <&mmc0_clk 0>,
-				 <&mmc0_clk 1>, <&mmc0_clk 2>;
+			clocks = <&mmc_config_clk 0>, <&ccu CLK_MMC0>,
+				 <&ccu CLK_MMC0_OUTPUT>,
+				 <&ccu CLK_MMC0_SAMPLE>;
 			clock-names = "ahb", "mmc", "output", "sample";
 			resets = <&mmc_config_clk 0>;
 			reset-names = "ahb";
@@ -556,11 +416,12 @@ 
 			#size-cells = <0>;
 		};
 
-		mmc1: mmc@01c10000 {
+		mmc1: mmc@1c10000 {
 			compatible = "allwinner,sun9i-a80-mmc";
 			reg = <0x01c10000 0x1000>;
-			clocks = <&mmc_config_clk 1>, <&mmc1_clk 0>,
-				 <&mmc1_clk 1>, <&mmc1_clk 2>;
+			clocks = <&mmc_config_clk 1>, <&ccu CLK_MMC1>,
+				 <&ccu CLK_MMC1_OUTPUT>,
+				 <&ccu CLK_MMC1_SAMPLE>;
 			clock-names = "ahb", "mmc", "output", "sample";
 			resets = <&mmc_config_clk 1>;
 			reset-names = "ahb";
@@ -570,11 +431,12 @@ 
 			#size-cells = <0>;
 		};
 
-		mmc2: mmc@01c11000 {
+		mmc2: mmc@1c11000 {
 			compatible = "allwinner,sun9i-a80-mmc";
 			reg = <0x01c11000 0x1000>;
-			clocks = <&mmc_config_clk 2>, <&mmc2_clk 0>,
-				 <&mmc2_clk 1>, <&mmc2_clk 2>;
+			clocks = <&mmc_config_clk 2>, <&ccu CLK_MMC2>,
+				 <&ccu CLK_MMC2_OUTPUT>,
+				 <&ccu CLK_MMC2_SAMPLE>;
 			clock-names = "ahb", "mmc", "output", "sample";
 			resets = <&mmc_config_clk 2>;
 			reset-names = "ahb";
@@ -584,11 +446,12 @@ 
 			#size-cells = <0>;
 		};
 
-		mmc3: mmc@01c12000 {
+		mmc3: mmc@1c12000 {
 			compatible = "allwinner,sun9i-a80-mmc";
 			reg = <0x01c12000 0x1000>;
-			clocks = <&mmc_config_clk 3>, <&mmc3_clk 0>,
-				 <&mmc3_clk 1>, <&mmc3_clk 2>;
+			clocks = <&mmc_config_clk 3>, <&ccu CLK_MMC3>,
+				 <&ccu CLK_MMC3_OUTPUT>,
+				 <&ccu CLK_MMC3_SAMPLE>;
 			clock-names = "ahb", "mmc", "output", "sample";
 			resets = <&mmc_config_clk 3>;
 			reset-names = "ahb";
@@ -598,12 +461,12 @@ 
 			#size-cells = <0>;
 		};
 
-		mmc_config_clk: clk@01c13000 {
+		mmc_config_clk: clk@1c13000 {
 			compatible = "allwinner,sun9i-a80-mmc-config-clk";
 			reg = <0x01c13000 0x10>;
-			clocks = <&ahb0_gates 8>;
+			clocks = <&ccu CLK_BUS_MMC>;
 			clock-names = "ahb";
-			resets = <&ahb0_resets 8>;
+			resets = <&ccu RST_BUS_MMC>;
 			reset-names = "ahb";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -611,10 +474,10 @@ 
 					     "mmc2_config", "mmc3_config";
 		};
 
-		gic: interrupt-controller@01c41000 {
+		gic: interrupt-controller@1c41000 {
 			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
 			reg = <0x01c41000 0x1000>,
-			      <0x01c42000 0x1000>,
+			      <0x01c42000 0x2000>,
 			      <0x01c44000 0x2000>,
 			      <0x01c46000 0x2000>;
 			interrupt-controller;
@@ -622,37 +485,435 @@ 
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
-		ahb0_resets: reset@060005a0 {
-			#reset-cells = <1>;
-			compatible = "allwinner,sun6i-a31-clock-reset";
-			reg = <0x060005a0 0x4>;
+		cci: cci@1c90000 {
+			compatible = "arm,cci-400";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x01c90000 0x1000>;
+			ranges = <0x0 0x01c90000 0x10000>;
+
+			cci_control0: slave-if@4000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x4000 0x1000>;
+			};
+
+			cci_control1: slave-if@5000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x5000 0x1000>;
+			};
+
+			pmu@9000 {
+				 compatible = "arm,cci-400-pmu,r1";
+				 reg = <0x9000 0x5000>;
+				 interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			};
 		};
 
-		ahb1_resets: reset@060005a4 {
+		de_clocks: clock@3000000 {
+			compatible = "allwinner,sun9i-a80-de-clks";
+			reg = <0x03000000 0x30>;
+			clocks = <&ccu CLK_DE>,
+				 <&ccu CLK_SDRAM>,
+				 <&ccu CLK_BUS_DE>;
+			clock-names = "mod",
+				      "dram",
+				      "bus";
+			resets = <&ccu RST_BUS_DE>;
+			#clock-cells = <1>;
 			#reset-cells = <1>;
-			compatible = "allwinner,sun6i-a31-clock-reset";
-			reg = <0x060005a4 0x4>;
 		};
 
-		ahb2_resets: reset@060005a8 {
-			#reset-cells = <1>;
-			compatible = "allwinner,sun6i-a31-clock-reset";
-			reg = <0x060005a8 0x4>;
+		fe0: display-frontend@3100000 {
+			compatible = "allwinner,sun9i-a80-display-frontend";
+			reg = <0x03100000 0x40000>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&de_clocks CLK_BUS_FE0>, <&de_clocks CLK_FE0>,
+				 <&de_clocks CLK_DRAM_FE0>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&de_clocks RST_FE0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fe0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					fe0_out_deu0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&deu0_in_fe0>;
+					};
+				};
+			};
 		};
 
-		apb0_resets: reset@060005b0 {
-			#reset-cells = <1>;
-			compatible = "allwinner,sun6i-a31-clock-reset";
-			reg = <0x060005b0 0x4>;
+		fe1: display-frontend@3140000 {
+			compatible = "allwinner,sun9i-a80-display-frontend";
+			reg = <0x03140000 0x40000>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&de_clocks CLK_BUS_FE1>, <&de_clocks CLK_FE1>,
+				 <&de_clocks CLK_DRAM_FE1>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&de_clocks RST_FE0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fe1_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					fe1_out_deu1: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&deu1_in_fe1>;
+					};
+				};
+			};
+		};
+
+		be0: display-backend@3200000 {
+			compatible = "allwinner,sun9i-a80-display-backend";
+			reg = <0x03200000 0x40000>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&de_clocks CLK_BUS_BE0>, <&de_clocks CLK_BE0>,
+				 <&de_clocks CLK_DRAM_BE0>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&de_clocks RST_BE0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				be0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					be0_in_deu0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&deu0_out_be0>;
+					};
+
+					be0_in_deu1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&deu1_out_be0>;
+					};
+				};
+
+				be0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					be0_out_drc0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&drc0_in_be0>;
+					};
+				};
+			};
+		};
+
+		be1: display-backend@3240000 {
+			compatible = "allwinner,sun9i-a80-display-backend";
+			reg = <0x03240000 0x40000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&de_clocks CLK_BUS_BE1>, <&de_clocks CLK_BE1>,
+				 <&de_clocks CLK_DRAM_BE1>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&de_clocks RST_BE1>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				be1_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					be1_in_deu0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&deu0_out_be1>;
+					};
+
+					be1_in_deu1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&deu1_out_be1>;
+					};
+				};
+
+				be1_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					be1_out_drc1: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&drc1_in_be1>;
+					};
+				};
+			};
+		};
+
+		deu0: deu@3300000 {
+			compatible = "allwinner,sun9i-a80-deu";
+			reg = <0x03300000 0x40000>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&de_clocks CLK_BUS_DEU0>,
+				 <&de_clocks CLK_IEP_DEU0>,
+				 <&de_clocks CLK_DRAM_DEU0>;
+			clock-names = "ahb",
+				      "mod",
+				      "ram";
+			resets = <&de_clocks RST_DEU0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				deu0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					deu0_in_fe0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&fe0_out_deu0>;
+					};
+				};
+
+				deu0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					deu0_out_be0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be0_in_deu0>;
+					};
+
+					deu0_out_be1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&be1_in_deu0>;
+					};
+				};
+			};
+		};
+
+		deu1: deu@3340000 {
+			compatible = "allwinner,sun9i-a80-deu";
+			reg = <0x03340000 0x40000>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&de_clocks CLK_BUS_DEU1>,
+				 <&de_clocks CLK_IEP_DEU1>,
+				 <&de_clocks CLK_DRAM_DEU1>;
+			clock-names = "ahb",
+				      "mod",
+				      "ram";
+			resets = <&de_clocks RST_DEU1>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				deu1_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					deu1_in_fe1: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&fe1_out_deu1>;
+					};
+				};
+
+				deu1_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					deu1_out_be0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be0_in_deu1>;
+					};
+
+					deu1_out_be1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&be1_in_deu1>;
+					};
+				};
+			};
+		};
+
+		drc0: drc@3400000 {
+			compatible = "allwinner,sun9i-a80-drc";
+			reg = <0x03400000 0x40000>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&de_clocks CLK_BUS_DRC0>,
+				 <&de_clocks CLK_IEP_DRC0>,
+				 <&de_clocks CLK_DRAM_DRC0>;
+			clock-names = "ahb",
+				      "mod",
+				      "ram";
+			resets = <&de_clocks RST_DRC0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				drc0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					drc0_in_be0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be0_out_drc0>;
+					};
+				};
+
+				drc0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					drc0_out_tcon0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon0_in_drc0>;
+					};
+				};
+			};
+		};
+
+		drc1: drc@3440000 {
+			compatible = "allwinner,sun9i-a80-drc";
+			reg = <0x03440000 0x40000>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&de_clocks CLK_BUS_DRC1>,
+				 <&de_clocks CLK_IEP_DRC1>,
+				 <&de_clocks CLK_DRAM_DRC1>;
+			clock-names = "ahb",
+				      "mod",
+				      "ram";
+			resets = <&de_clocks RST_DRC1>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				drc1_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					drc1_in_be1: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be1_out_drc1>;
+					};
+				};
+
+				drc1_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					drc1_out_tcon1: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon1_in_drc1>;
+					};
+				};
+			};
+		};
+
+		tcon0: lcd-controller@3c00000 {
+			compatible = "allwinner,sun9i-a80-tcon-lcd";
+			reg = <0x03c00000 0x10000>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_LCD0>, <&ccu CLK_LCD0>;
+			clock-names = "ahb", "tcon-ch0";
+			resets = <&ccu RST_BUS_LCD0>, <&ccu RST_BUS_EDP>;
+			reset-names = "lcd", "edp";
+			clock-output-names = "tcon0-pixel-clock";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					tcon0_in_drc0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&drc0_out_tcon0>;
+					};
+				};
+
+				tcon0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+			};
 		};
 
-		apb1_resets: reset@060005b4 {
+		tcon1: lcd-controller@3c10000 {
+			compatible = "allwinner,sun9i-a80-tcon-tv";
+			reg = <0x03c10000 0x10000>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_LCD1>, <&ccu CLK_LCD1>;
+			clock-names = "ahb", "tcon-ch1";
+			resets = <&ccu RST_BUS_LCD1>, <&ccu RST_BUS_EDP>;
+			reset-names = "lcd", "edp";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon1_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					tcon1_in_drc1: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&drc1_out_tcon1>;
+					};
+				};
+
+				tcon1_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+			};
+		};
+
+		ccu: clock@6000000 {
+			compatible = "allwinner,sun9i-a80-ccu";
+			reg = <0x06000000 0x800>;
+			clocks = <&osc24M>, <&osc32k>;
+			clock-names = "hosc", "losc";
+			#clock-cells = <1>;
 			#reset-cells = <1>;
-			compatible = "allwinner,sun6i-a31-clock-reset";
-			reg = <0x060005b4 0x4>;
 		};
 
-		timer@06000c00 {
+		timer@6000c00 {
 			compatible = "allwinner,sun4i-a10-timer";
 			reg = <0x06000c00 0xa0>;
 			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
@@ -665,13 +926,13 @@ 
 			clocks = <&osc24M>;
 		};
 
-		wdt: watchdog@06000ca0 {
+		wdt: watchdog@6000ca0 {
 			compatible = "allwinner,sun6i-a31-wdt";
 			reg = <0x06000ca0 0x20>;
 			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		pio: pinctrl@06000800 {
+		pio: pinctrl@6000800 {
 			compatible = "allwinner,sun9i-a80-pinctrl";
 			reg = <0x06000800 0x400>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
@@ -679,195 +940,206 @@ 
 				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb0_gates 5>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			#size-cells = <0>;
 			#gpio-cells = <3>;
 
-			i2c3_pins_a: i2c3@0 {
-				allwinner,pins = "PG10", "PG11";
-				allwinner,function = "i2c3";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			i2c3_pins: i2c3-pins {
+				pins = "PG10", "PG11";
+				function = "i2c3";
+			};
+
+			lcd0_rgb888_pins: lcd0-rgb888-pins {
+				pins = "PD0", "PD1", "PD2", "PD3",
+				       "PD4", "PD5", "PD6", "PD7",
+				       "PD8", "PD9", "PD10", "PD11",
+				       "PD12", "PD13", "PD14", "PD15",
+				       "PD16", "PD17", "PD18", "PD19",
+				       "PD20", "PD21", "PD22", "PD23",
+				       "PD24", "PD25", "PD26", "PD27";
+				function = "lcd0";
 			};
 
-			mmc0_pins: mmc0 {
-				allwinner,pins = "PF0", "PF1" ,"PF2", "PF3",
-						 "PF4", "PF5";
-				allwinner,function = "mmc0";
-				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1" ,"PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
 			};
 
-			mmc1_pins: mmc1 {
-				allwinner,pins = "PG0", "PG1" ,"PG2", "PG3",
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1" ,"PG2", "PG3",
 						 "PG4", "PG5";
-				allwinner,function = "mmc1";
-				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
 			};
 
-			mmc2_8bit_pins: mmc2_8bit {
-				allwinner,pins = "PC6", "PC7", "PC8", "PC9",
-						 "PC10", "PC11", "PC12",
-						 "PC13", "PC14", "PC15",
-						 "PC16";
-				allwinner,function = "mmc2";
-				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			mmc2_8bit_pins: mmc2-8bit-pins {
+				pins = "PC6", "PC7", "PC8", "PC9",
+				       "PC10", "PC11", "PC12",
+				       "PC13", "PC14", "PC15",
+				       "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
 			};
 
-			uart0_pins_a: uart0@0 {
-				allwinner,pins = "PH12", "PH13";
-				allwinner,function = "uart0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			uart0_ph_pins: uart0-ph-pins {
+				pins = "PH12", "PH13";
+				function = "uart0";
 			};
 
-			uart4_pins_a: uart4@0 {
-				allwinner,pins = "PG12", "PG13", "PG14", "PG15";
-				allwinner,function = "uart4";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			uart4_pins: uart4-pins {
+				pins = "PG12", "PG13", "PG14", "PG15";
+				function = "uart4";
 			};
 		};
 
-		uart0: serial@07000000 {
+		uart0: serial@7000000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x07000000 0x400>;
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 16>;
-			resets = <&apb1_resets 16>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
 
-		uart1: serial@07000400 {
+		uart1: serial@7000400 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x07000400 0x400>;
 			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 17>;
-			resets = <&apb1_resets 17>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
 
-		uart2: serial@07000800 {
+		uart2: serial@7000800 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x07000800 0x400>;
 			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 18>;
-			resets = <&apb1_resets 18>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
 			status = "disabled";
 		};
 
-		uart3: serial@07000c00 {
+		uart3: serial@7000c00 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x07000c00 0x400>;
 			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 19>;
-			resets = <&apb1_resets 19>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
 			status = "disabled";
 		};
 
-		uart4: serial@07001000 {
+		uart4: serial@7001000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x07001000 0x400>;
 			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 20>;
-			resets = <&apb1_resets 20>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
 			status = "disabled";
 		};
 
-		uart5: serial@07001400 {
+		uart5: serial@7001400 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x07001400 0x400>;
 			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 21>;
-			resets = <&apb1_resets 21>;
+			clocks = <&ccu CLK_BUS_UART5>;
+			resets = <&ccu RST_BUS_UART5>;
 			status = "disabled";
 		};
 
-		i2c0: i2c@07002800 {
+		i2c0: i2c@7002800 {
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x07002800 0x400>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb1_gates 0>;
-			resets = <&apb1_resets 0>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		i2c1: i2c@07002c00 {
+		i2c1: i2c@7002c00 {
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x07002c00 0x400>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb1_gates 1>;
-			resets = <&apb1_resets 1>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		i2c2: i2c@07003000 {
+		i2c2: i2c@7003000 {
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x07003000 0x400>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb1_gates 2>;
-			resets = <&apb1_resets 2>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		i2c3: i2c@07003400 {
+		i2c3: i2c@7003400 {
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x07003400 0x400>;
 			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb1_gates 3>;
-			resets = <&apb1_resets 3>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		i2c4: i2c@07003800 {
+		i2c4: i2c@7003800 {
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x07003800 0x400>;
 			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb1_gates 4>;
-			resets = <&apb1_resets 4>;
+			clocks = <&ccu CLK_BUS_I2C4>;
+			resets = <&ccu RST_BUS_I2C4>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		r_wdt: watchdog@08001000 {
+		r_wdt: watchdog@8001000 {
 			compatible = "allwinner,sun6i-a31-wdt";
 			reg = <0x08001000 0x20>;
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		apbs_rst: reset@080014b0 {
+		prcm@8001400 {
+			compatible = "allwinner,sun9i-a80-prcm";
+			reg = <0x08001400 0x200>;
+		};
+
+		apbs_rst: reset@80014b0 {
 			reg = <0x080014b0 0x4>;
 			compatible = "allwinner,sun6i-a31-clock-reset";
 			#reset-cells = <1>;
 		};
 
-		nmi_intc: interrupt-controller@080015a0 {
+		nmi_intc: interrupt-controller@80015a0 {
 			compatible = "allwinner,sun9i-a80-nmi";
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -875,7 +1147,7 @@ 
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		r_ir: ir@08002000 {
+		r_ir: ir@8002000 {
 			compatible = "allwinner,sun5i-a13-ir";
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
@@ -887,7 +1159,7 @@ 
 			status = "disabled";
 		};
 
-		r_uart: serial@08002800 {
+		r_uart: serial@8002800 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x08002800 0x400>;
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
@@ -898,35 +1170,33 @@ 
 			status = "disabled";
 		};
 
-		r_pio: pinctrl@08002c00 {
+		r_pio: pinctrl@8002c00 {
 			compatible = "allwinner,sun9i-a80-r-pinctrl";
 			reg = <0x08002c00 0x400>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apbs_gates 0>;
+			clocks = <&apbs_gates 0>, <&osc24M>, <&osc32k>;
+			clock-names = "apb", "hosc", "losc";
 			resets = <&apbs_rst 0>;
 			gpio-controller;
 			interrupt-controller;
-			#address-cells = <1>;
-			#size-cells = <0>;
+			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
-			r_ir_pins: r_ir {
-				allwinner,pins = "PL6";
-				allwinner,function = "s_cir_rx";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			r_ir_pins: r-ir-pins {
+				pins = "PL6";
+				function = "s_cir_rx";
 			};
 
-			r_rsb_pins: r_rsb {
-				allwinner,pins = "PN0", "PN1";
-				allwinner,function = "s_rsb";
-				allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+			r_rsb_pins: r-rsb-pins {
+				pins = "PN0", "PN1";
+				function = "s_rsb";
+				drive-strength = <20>;
+				bias-pull-up;
 			};
 		};
 
-		r_rsb: i2c@08003400 {
+		r_rsb: i2c@8003400 {
 			compatible = "allwinner,sun8i-a23-rsb";
 			reg = <0x08003400 0x400>;
 			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/include/dt-bindings/clock/sun9i-a80-ccu.h b/include/dt-bindings/clock/sun9i-a80-ccu.h
new file mode 100644
index 0000000000..6ea1492a73
--- /dev/null
+++ b/include/dt-bindings/clock/sun9i-a80-ccu.h
@@ -0,0 +1,162 @@ 
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_SUN9I_A80_CCU_H_
+#define _DT_BINDINGS_CLOCK_SUN9I_A80_CCU_H_
+
+#define CLK_PLL_AUDIO		2
+#define CLK_PLL_PERIPH0		3
+
+#define CLK_C0CPUX		12
+#define CLK_C1CPUX		13
+
+#define CLK_OUT_A		27
+#define CLK_OUT_B		28
+
+#define CLK_NAND0_0		29
+#define CLK_NAND0_1		30
+#define CLK_NAND1_0		31
+#define CLK_NAND1_1		32
+#define CLK_MMC0		33
+#define CLK_MMC0_SAMPLE		34
+#define CLK_MMC0_OUTPUT		35
+#define CLK_MMC1		36
+#define CLK_MMC1_SAMPLE		37
+#define CLK_MMC1_OUTPUT		38
+#define CLK_MMC2		39
+#define CLK_MMC2_SAMPLE		40
+#define CLK_MMC2_OUTPUT		41
+#define CLK_MMC3		42
+#define CLK_MMC3_SAMPLE		43
+#define CLK_MMC3_OUTPUT		44
+#define CLK_TS			45
+#define CLK_SS			46
+#define CLK_SPI0		47
+#define CLK_SPI1		48
+#define CLK_SPI2		49
+#define CLK_SPI3		50
+#define CLK_I2S0		51
+#define CLK_I2S1		52
+#define CLK_SPDIF		53
+#define CLK_SDRAM		54
+#define CLK_DE			55
+#define CLK_EDP			56
+#define CLK_MP			57
+#define CLK_LCD0		58
+#define CLK_LCD1		59
+#define CLK_MIPI_DSI0		60
+#define CLK_MIPI_DSI1		61
+#define CLK_HDMI		62
+#define CLK_HDMI_SLOW		63
+#define CLK_MIPI_CSI		64
+#define CLK_CSI_ISP		65
+#define CLK_CSI_MISC		66
+#define CLK_CSI0_MCLK		67
+#define CLK_CSI1_MCLK		68
+#define CLK_FD			69
+#define CLK_VE			70
+#define CLK_AVS			71
+#define CLK_GPU_CORE		72
+#define CLK_GPU_MEMORY		73
+#define CLK_GPU_AXI		74
+#define CLK_SATA		75
+#define CLK_AC97		76
+#define CLK_MIPI_HSI		77
+#define CLK_GPADC		78
+#define CLK_CIR_TX		79
+
+#define CLK_BUS_FD		80
+#define CLK_BUS_VE		81
+#define CLK_BUS_GPU_CTRL	82
+#define CLK_BUS_SS		83
+#define CLK_BUS_MMC		84
+#define CLK_BUS_NAND0		85
+#define CLK_BUS_NAND1		86
+#define CLK_BUS_SDRAM		87
+#define CLK_BUS_MIPI_HSI	88
+#define CLK_BUS_SATA		89
+#define CLK_BUS_TS		90
+#define CLK_BUS_SPI0		91
+#define CLK_BUS_SPI1		92
+#define CLK_BUS_SPI2		93
+#define CLK_BUS_SPI3		94
+
+#define CLK_BUS_OTG		95
+#define CLK_BUS_USB		96
+#define CLK_BUS_GMAC		97
+#define CLK_BUS_MSGBOX		98
+#define CLK_BUS_SPINLOCK	99
+#define CLK_BUS_HSTIMER		100
+#define CLK_BUS_DMA		101
+
+#define CLK_BUS_LCD0		102
+#define CLK_BUS_LCD1		103
+#define CLK_BUS_EDP		104
+#define CLK_BUS_CSI		105
+#define CLK_BUS_HDMI		106
+#define CLK_BUS_DE		107
+#define CLK_BUS_MP		108
+#define CLK_BUS_MIPI_DSI	109
+
+#define CLK_BUS_SPDIF		110
+#define CLK_BUS_PIO		111
+#define CLK_BUS_AC97		112
+#define CLK_BUS_I2S0		113
+#define CLK_BUS_I2S1		114
+#define CLK_BUS_LRADC		115
+#define CLK_BUS_GPADC		116
+#define CLK_BUS_TWD		117
+#define CLK_BUS_CIR_TX		118
+
+#define CLK_BUS_I2C0		119
+#define CLK_BUS_I2C1		120
+#define CLK_BUS_I2C2		121
+#define CLK_BUS_I2C3		122
+#define CLK_BUS_I2C4		123
+#define CLK_BUS_UART0		124
+#define CLK_BUS_UART1		125
+#define CLK_BUS_UART2		126
+#define CLK_BUS_UART3		127
+#define CLK_BUS_UART4		128
+#define CLK_BUS_UART5		129
+
+#endif /* _DT_BINDINGS_CLOCK_SUN9I_A80_CCU_H_ */
diff --git a/include/dt-bindings/clock/sun9i-a80-de.h b/include/dt-bindings/clock/sun9i-a80-de.h
new file mode 100644
index 0000000000..3dad6c3cd1
--- /dev/null
+++ b/include/dt-bindings/clock/sun9i-a80-de.h
@@ -0,0 +1,80 @@ 
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_SUN9I_A80_DE_H_
+#define _DT_BINDINGS_CLOCK_SUN9I_A80_DE_H_
+
+#define CLK_FE0			0
+#define CLK_FE1			1
+#define CLK_FE2			2
+#define CLK_IEP_DEU0		3
+#define CLK_IEP_DEU1		4
+#define CLK_BE0			5
+#define CLK_BE1			6
+#define CLK_BE2			7
+#define CLK_IEP_DRC0		8
+#define CLK_IEP_DRC1		9
+#define CLK_MERGE		10
+
+#define CLK_DRAM_FE0		11
+#define CLK_DRAM_FE1		12
+#define CLK_DRAM_FE2		13
+#define CLK_DRAM_DEU0		14
+#define CLK_DRAM_DEU1		15
+#define CLK_DRAM_BE0		16
+#define CLK_DRAM_BE1		17
+#define CLK_DRAM_BE2		18
+#define CLK_DRAM_DRC0		19
+#define CLK_DRAM_DRC1		20
+
+#define CLK_BUS_FE0		21
+#define CLK_BUS_FE1		22
+#define CLK_BUS_FE2		23
+#define CLK_BUS_DEU0		24
+#define CLK_BUS_DEU1		25
+#define CLK_BUS_BE0		26
+#define CLK_BUS_BE1		27
+#define CLK_BUS_BE2		28
+#define CLK_BUS_DRC0		29
+#define CLK_BUS_DRC1		30
+
+#endif /* _DT_BINDINGS_CLOCK_SUN9I_A80_DE_H_ */
diff --git a/include/dt-bindings/clock/sun9i-a80-usb.h b/include/dt-bindings/clock/sun9i-a80-usb.h
new file mode 100644
index 0000000000..783a60d2cc
--- /dev/null
+++ b/include/dt-bindings/clock/sun9i-a80-usb.h
@@ -0,0 +1,59 @@ 
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_SUN9I_A80_USB_H_
+#define _DT_BINDINGS_CLOCK_SUN9I_A80_USB_H_
+
+#define CLK_BUS_HCI0	0
+#define CLK_USB_OHCI0	1
+#define CLK_BUS_HCI1	2
+#define CLK_BUS_HCI2	3
+#define CLK_USB_OHCI2	4
+
+#define CLK_USB0_PHY	5
+#define CLK_USB1_HSIC	6
+#define CLK_USB1_PHY	7
+#define CLK_USB2_HSIC	8
+#define CLK_USB2_PHY	9
+#define CLK_USB_HSIC	10
+
+#endif /* _DT_BINDINGS_CLOCK_SUN9I_A80_USB_H_ */
diff --git a/include/dt-bindings/reset/sun9i-a80-ccu.h b/include/dt-bindings/reset/sun9i-a80-ccu.h
new file mode 100644
index 0000000000..4b8df4b367
--- /dev/null
+++ b/include/dt-bindings/reset/sun9i-a80-ccu.h
@@ -0,0 +1,102 @@ 
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN9I_A80_CCU_H_
+#define _DT_BINDINGS_RESET_SUN9I_A80_CCU_H_
+
+#define RST_BUS_FD		0
+#define RST_BUS_VE		1
+#define RST_BUS_GPU_CTRL	2
+#define RST_BUS_SS		3
+#define RST_BUS_MMC		4
+#define RST_BUS_NAND0		5
+#define RST_BUS_NAND1		6
+#define RST_BUS_SDRAM		7
+#define RST_BUS_SATA		8
+#define RST_BUS_TS		9
+#define RST_BUS_SPI0		10
+#define RST_BUS_SPI1		11
+#define RST_BUS_SPI2		12
+#define RST_BUS_SPI3		13
+
+#define RST_BUS_OTG		14
+#define RST_BUS_OTG_PHY		15
+#define RST_BUS_MIPI_HSI	16
+#define RST_BUS_GMAC		17
+#define RST_BUS_MSGBOX		18
+#define RST_BUS_SPINLOCK	19
+#define RST_BUS_HSTIMER		20
+#define RST_BUS_DMA		21
+
+#define RST_BUS_LCD0		22
+#define RST_BUS_LCD1		23
+#define RST_BUS_EDP		24
+#define RST_BUS_LVDS		25
+#define RST_BUS_CSI		26
+#define RST_BUS_HDMI0		27
+#define RST_BUS_HDMI1		28
+#define RST_BUS_DE		29
+#define RST_BUS_MP		30
+#define RST_BUS_GPU		31
+#define RST_BUS_MIPI_DSI	32
+
+#define RST_BUS_SPDIF		33
+#define RST_BUS_AC97		34
+#define RST_BUS_I2S0		35
+#define RST_BUS_I2S1		36
+#define RST_BUS_LRADC		37
+#define RST_BUS_GPADC		38
+#define RST_BUS_CIR_TX		39
+
+#define RST_BUS_I2C0		40
+#define RST_BUS_I2C1		41
+#define RST_BUS_I2C2		42
+#define RST_BUS_I2C3		43
+#define RST_BUS_I2C4		44
+#define RST_BUS_UART0		45
+#define RST_BUS_UART1		46
+#define RST_BUS_UART2		47
+#define RST_BUS_UART3		48
+#define RST_BUS_UART4		49
+#define RST_BUS_UART5		50
+
+#endif /* _DT_BINDINGS_RESET_SUN9I_A80_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun9i-a80-de.h b/include/dt-bindings/reset/sun9i-a80-de.h
new file mode 100644
index 0000000000..2050727701
--- /dev/null
+++ b/include/dt-bindings/reset/sun9i-a80-de.h
@@ -0,0 +1,58 @@ 
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN9I_A80_DE_H_
+#define _DT_BINDINGS_RESET_SUN9I_A80_DE_H_
+
+#define RST_FE0		0
+#define RST_FE1		1
+#define RST_FE2		2
+#define RST_DEU0	3
+#define RST_DEU1	4
+#define RST_BE0		5
+#define RST_BE1		6
+#define RST_BE2		7
+#define RST_DRC0	8
+#define RST_DRC1	9
+#define RST_MERGE	10
+
+#endif /* _DT_BINDINGS_RESET_SUN9I_A80_DE_H_ */
diff --git a/include/dt-bindings/reset/sun9i-a80-usb.h b/include/dt-bindings/reset/sun9i-a80-usb.h
new file mode 100644
index 0000000000..ee492864c2
--- /dev/null
+++ b/include/dt-bindings/reset/sun9i-a80-usb.h
@@ -0,0 +1,56 @@ 
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN9I_A80_USB_H_
+#define _DT_BINDINGS_RESET_SUN9I_A80_USB_H_
+
+#define RST_USB0_HCI	0
+#define RST_USB1_HCI	1
+#define RST_USB2_HCI	2
+
+#define RST_USB0_PHY	3
+#define RST_USB1_HSIC	4
+#define RST_USB1_PHY	5
+#define RST_USB2_HSIC	6
+#define RST_USB2_PHY	7
+
+#endif /* _DT_BINDINGS_RESET_SUN9I_A80_USB_H_ */