[V4,01/20] dt-bindings: clock: tegra124-dfll: Update DFLL binding for PWM regulator

Message ID 20190104030702.8684-2-josephl@nvidia.com
State New
Headers show
Series
  • Tegra210 DFLL support
Related show

Commit Message

Joseph Lo Jan. 4, 2019, 3:06 a.m.
From: Peter De Schrijver <pdeschrijver@nvidia.com>

Add new properties to configure the DFLL PWM regulator support.

Cc: devicetree@vger.kernel.org
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
---
*V4:
 - s/nvidia,pwm-period/nvidia,pwm-period-nanoseconds/
*V3:
 - no change
*V2:
 - update the binding strings and descriptions for
 nvidia,pwm-tristate-microvolts
 nvidia,pwm-min-microvolts
 nvidia,pwm-voltage-step-microvolts
---
 .../bindings/clock/nvidia,tegra124-dfll.txt   | 79 ++++++++++++++++++-
 1 file changed, 77 insertions(+), 2 deletions(-)

Comments

Joseph Lo Jan. 8, 2019, 12:35 a.m. | #1
On 1/4/19 11:06 AM, Joseph Lo wrote:
> From: Peter De Schrijver <pdeschrijver@nvidia.com>
> 
> Add new properties to configure the DFLL PWM regulator support.
> 
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
> Signed-off-by: Joseph Lo <josephl@nvidia.com>
> Acked-by: Jon Hunter <jonathanh@nvidia.com>
> ---
> *V4:
>   - s/nvidia,pwm-period/nvidia,pwm-period-nanoseconds/
> *V3:
>   - no change
> *V2:
>   - update the binding strings and descriptions for
>   nvidia,pwm-tristate-microvolts
>   nvidia,pwm-min-microvolts
>   nvidia,pwm-voltage-step-microvolts
> ---

Hi Rob,

Could you help me to review this patch again?

Thanks,
Joseph

>   .../bindings/clock/nvidia,tegra124-dfll.txt   | 79 ++++++++++++++++++-
>   1 file changed, 77 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
> index dff236f524a7..5558bb5fcf2c 100644
> --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
> +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
> @@ -8,7 +8,6 @@ the fast CPU cluster. It consists of a free-running voltage controlled
>   oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop
>   control module that will automatically adjust the VDD_CPU voltage by
>   communicating with an off-chip PMIC either via an I2C bus or via PWM signals.
> -Currently only the I2C mode is supported by these bindings.
>   
>   Required properties:
>   - compatible : should be "nvidia,tegra124-dfll"
> @@ -45,10 +44,31 @@ Required properties for the control loop parameters:
>   Optional properties for the control loop parameters:
>   - nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM.
>   
> +Optional properties for mode selection:
> +- nvidia,pwm-to-pmic: Use PWM to control regulator rather then I2C.
> +
>   Required properties for I2C mode:
>   - nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode.
>   
> -Example:
> +Required properties for PWM mode:
> +- nvidia,pwm-period-nanoseconds: period of PWM square wave in nanoseconds.
> +- nvidia,pwm-tristate-microvolts: Regulator voltage in micro volts when PWM
> +  control is disabled and the PWM output is tristated. Note that this voltage is
> +  configured in hardware, typically via a resistor divider.
> +- nvidia,pwm-min-microvolts: Regulator voltage in micro volts when PWM control
> +  is enabled and PWM output is low. Hence, this is the minimum output voltage
> +  that the regulator supports when PWM control is enabled.
> +- nvidia,pwm-voltage-step-microvolts: Voltage increase in micro volts
> +  corresponding to a 1/33th increase in duty cycle. Eg the voltage for 2/33th
> +  duty cycle would be: nvidia,pwm-min-microvolts +
> +  nvidia,pwm-voltage-step-microvolts * 2.
> +- pinctrl-0: I/O pad configuration when PWM control is enabled.
> +- pinctrl-1: I/O pad configuration when PWM control is disabled.
> +- pinctrl-names: must include the following entries:
> +  - dvfs_pwm_enable: I/O pad configuration when PWM control is enabled.
> +  - dvfs_pwm_disable: I/O pad configuration when PWM control is disabled.
> +
> +Example for I2C:
>   
>   clock@70110000 {
>           compatible = "nvidia,tegra124-dfll";
> @@ -76,3 +96,58 @@ clock@70110000 {
>   
>           nvidia,i2c-fs-rate = <400000>;
>   };
> +
> +Example for PWM:
> +
> +clock@70110000 {
> +	compatible = "nvidia,tegra124-dfll";
> +	reg = <0 0x70110000 0 0x100>, /* DFLL control */
> +	      <0 0x70110000 0 0x100>, /* I2C output control */
> +	      <0 0x70110100 0 0x100>, /* Integrated I2C controller */
> +	      <0 0x70110200 0 0x100>; /* Look-up table RAM */
> +	interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> +	clocks = <&tegra_car TEGRA210_CLK_DFLL_SOC>,
> +	         <&tegra_car TEGRA210_CLK_DFLL_REF>,
> +		 <&tegra_car TEGRA124_CLK_I2C5>;;
> +	clock-names = "soc", "ref", "i2c";
> +	resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>;
> +	reset-names = "dvco";
> +	#clock-cells = <0>;
> +	clock-output-names = "dfllCPU_out";
> +
> +	nvidia,sample-rate = <25000>;
> +	nvidia,droop-ctrl = <0x00000f00>;
> +	nvidia,force-mode = <1>;
> +	nvidia,cf = <6>;
> +	nvidia,ci = <0>;
> +	nvidia,cg = <2>;
> +
> +	nvidia,pwm-min-microvolts = <708000>; /* 708mV */
> +	nvidia,pwm-period-nanoseconds = <2500>; /* 2.5us */
> +	nvidia,pwm-to-pmic;
> +	nvidia,pwm-tristate-microvolts = <1000000>;
> +	nvidia,pwm-voltage-step-microvolts = <19200>; /* 19.2mV */
> +
> +	pinctrl-names = "dvfs_pwm_enable", "dvfs_pwm_disable";
> +	pinctrl-0 = <&dvfs_pwm_active_state>;
> +	pinctrl-1 = <&dvfs_pwm_inactive_state>;
> +};
> +
> +/* pinmux nodes added for completeness. Binding doc can be found in:
> + * Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
> + */
> +
> +pinmux: pinmux@700008d4 {
> +	dvfs_pwm_active_state: dvfs_pwm_active {
> +		dvfs_pwm_pbb1 {
> +			nvidia,pins = "dvfs_pwm_pbb1";
> +			nvidia,tristate = <TEGRA_PIN_DISABLE>;
> +		};
> +	};
> +	dvfs_pwm_inactive_state: dvfs_pwm_inactive {
> +		dvfs_pwm_pbb1 {
> +			nvidia,pins = "dvfs_pwm_pbb1";
> +			nvidia,tristate = <TEGRA_PIN_ENABLE>;
> +		};
> +	};
> +};
>
Joseph Lo Jan. 11, 2019, 8:14 a.m. | #2
On 1/8/19 8:35 AM, Joseph Lo wrote:
> On 1/4/19 11:06 AM, Joseph Lo wrote:
>> From: Peter De Schrijver <pdeschrijver@nvidia.com>
>>
>> Add new properties to configure the DFLL PWM regulator support.
>>
>> Cc: devicetree@vger.kernel.org
>> Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
>> Signed-off-by: Joseph Lo <josephl@nvidia.com>
>> Acked-by: Jon Hunter <jonathanh@nvidia.com>
>> ---
>> *V4:
>>   - s/nvidia,pwm-period/nvidia,pwm-period-nanoseconds/
>> *V3:
>>   - no change
>> *V2:
>>   - update the binding strings and descriptions for
>>   nvidia,pwm-tristate-microvolts
>>   nvidia,pwm-min-microvolts
>>   nvidia,pwm-voltage-step-microvolts
>> ---
> 
> Hi Rob,
> 
> Could you help me to review this patch again?

Gentle ping.

Thanks,
Joseph

> 
> Thanks,
> Joseph
> 
>>   .../bindings/clock/nvidia,tegra124-dfll.txt   | 79 ++++++++++++++++++-
>>   1 file changed, 77 insertions(+), 2 deletions(-)
>>
>> diff --git 
>> a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt 
>> b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
>> index dff236f524a7..5558bb5fcf2c 100644
>> --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
>> +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
>> @@ -8,7 +8,6 @@ the fast CPU cluster. It consists of a free-running 
>> voltage controlled
>>   oscillator connected to the CPU voltage rail (VDD_CPU), and a closed 
>> loop
>>   control module that will automatically adjust the VDD_CPU voltage by
>>   communicating with an off-chip PMIC either via an I2C bus or via PWM 
>> signals.
>> -Currently only the I2C mode is supported by these bindings.
>>   Required properties:
>>   - compatible : should be "nvidia,tegra124-dfll"
>> @@ -45,10 +44,31 @@ Required properties for the control loop parameters:
>>   Optional properties for the control loop parameters:
>>   - nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE 
>> in the TRM.
>> +Optional properties for mode selection:
>> +- nvidia,pwm-to-pmic: Use PWM to control regulator rather then I2C.
>> +
>>   Required properties for I2C mode:
>>   - nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode.
>> -Example:
>> +Required properties for PWM mode:
>> +- nvidia,pwm-period-nanoseconds: period of PWM square wave in 
>> nanoseconds.
>> +- nvidia,pwm-tristate-microvolts: Regulator voltage in micro volts 
>> when PWM
>> +  control is disabled and the PWM output is tristated. Note that this 
>> voltage is
>> +  configured in hardware, typically via a resistor divider.
>> +- nvidia,pwm-min-microvolts: Regulator voltage in micro volts when 
>> PWM control
>> +  is enabled and PWM output is low. Hence, this is the minimum output 
>> voltage
>> +  that the regulator supports when PWM control is enabled.
>> +- nvidia,pwm-voltage-step-microvolts: Voltage increase in micro volts
>> +  corresponding to a 1/33th increase in duty cycle. Eg the voltage 
>> for 2/33th
>> +  duty cycle would be: nvidia,pwm-min-microvolts +
>> +  nvidia,pwm-voltage-step-microvolts * 2.
>> +- pinctrl-0: I/O pad configuration when PWM control is enabled.
>> +- pinctrl-1: I/O pad configuration when PWM control is disabled.
>> +- pinctrl-names: must include the following entries:
>> +  - dvfs_pwm_enable: I/O pad configuration when PWM control is enabled.
>> +  - dvfs_pwm_disable: I/O pad configuration when PWM control is 
>> disabled.
>> +
>> +Example for I2C:
>>   clock@70110000 {
>>           compatible = "nvidia,tegra124-dfll";
>> @@ -76,3 +96,58 @@ clock@70110000 {
>>           nvidia,i2c-fs-rate = <400000>;
>>   };
>> +
>> +Example for PWM:
>> +
>> +clock@70110000 {
>> +    compatible = "nvidia,tegra124-dfll";
>> +    reg = <0 0x70110000 0 0x100>, /* DFLL control */
>> +          <0 0x70110000 0 0x100>, /* I2C output control */
>> +          <0 0x70110100 0 0x100>, /* Integrated I2C controller */
>> +          <0 0x70110200 0 0x100>; /* Look-up table RAM */
>> +    interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
>> +    clocks = <&tegra_car TEGRA210_CLK_DFLL_SOC>,
>> +             <&tegra_car TEGRA210_CLK_DFLL_REF>,
>> +         <&tegra_car TEGRA124_CLK_I2C5>;;
>> +    clock-names = "soc", "ref", "i2c";
>> +    resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>;
>> +    reset-names = "dvco";
>> +    #clock-cells = <0>;
>> +    clock-output-names = "dfllCPU_out";
>> +
>> +    nvidia,sample-rate = <25000>;
>> +    nvidia,droop-ctrl = <0x00000f00>;
>> +    nvidia,force-mode = <1>;
>> +    nvidia,cf = <6>;
>> +    nvidia,ci = <0>;
>> +    nvidia,cg = <2>;
>> +
>> +    nvidia,pwm-min-microvolts = <708000>; /* 708mV */
>> +    nvidia,pwm-period-nanoseconds = <2500>; /* 2.5us */
>> +    nvidia,pwm-to-pmic;
>> +    nvidia,pwm-tristate-microvolts = <1000000>;
>> +    nvidia,pwm-voltage-step-microvolts = <19200>; /* 19.2mV */
>> +
>> +    pinctrl-names = "dvfs_pwm_enable", "dvfs_pwm_disable";
>> +    pinctrl-0 = <&dvfs_pwm_active_state>;
>> +    pinctrl-1 = <&dvfs_pwm_inactive_state>;
>> +};
>> +
>> +/* pinmux nodes added for completeness. Binding doc can be found in:
>> + * Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
>> + */
>> +
>> +pinmux: pinmux@700008d4 {
>> +    dvfs_pwm_active_state: dvfs_pwm_active {
>> +        dvfs_pwm_pbb1 {
>> +            nvidia,pins = "dvfs_pwm_pbb1";
>> +            nvidia,tristate = <TEGRA_PIN_DISABLE>;
>> +        };
>> +    };
>> +    dvfs_pwm_inactive_state: dvfs_pwm_inactive {
>> +        dvfs_pwm_pbb1 {
>> +            nvidia,pins = "dvfs_pwm_pbb1";
>> +            nvidia,tristate = <TEGRA_PIN_ENABLE>;
>> +        };
>> +    };
>> +};
>>
Rob Herring Jan. 11, 2019, 7:32 p.m. | #3
On Fri, 4 Jan 2019 11:06:43 +0800, Joseph Lo wrote:
> From: Peter De Schrijver <pdeschrijver@nvidia.com>
> 
> Add new properties to configure the DFLL PWM regulator support.
> 
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
> Signed-off-by: Joseph Lo <josephl@nvidia.com>
> Acked-by: Jon Hunter <jonathanh@nvidia.com>
> ---
> *V4:
>  - s/nvidia,pwm-period/nvidia,pwm-period-nanoseconds/
> *V3:
>  - no change
> *V2:
>  - update the binding strings and descriptions for
>  nvidia,pwm-tristate-microvolts
>  nvidia,pwm-min-microvolts
>  nvidia,pwm-voltage-step-microvolts
> ---
>  .../bindings/clock/nvidia,tegra124-dfll.txt   | 79 ++++++++++++++++++-
>  1 file changed, 77 insertions(+), 2 deletions(-)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Patch

diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
index dff236f524a7..5558bb5fcf2c 100644
--- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
+++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
@@ -8,7 +8,6 @@  the fast CPU cluster. It consists of a free-running voltage controlled
 oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop
 control module that will automatically adjust the VDD_CPU voltage by
 communicating with an off-chip PMIC either via an I2C bus or via PWM signals.
-Currently only the I2C mode is supported by these bindings.
 
 Required properties:
 - compatible : should be "nvidia,tegra124-dfll"
@@ -45,10 +44,31 @@  Required properties for the control loop parameters:
 Optional properties for the control loop parameters:
 - nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM.
 
+Optional properties for mode selection:
+- nvidia,pwm-to-pmic: Use PWM to control regulator rather then I2C.
+
 Required properties for I2C mode:
 - nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode.
 
-Example:
+Required properties for PWM mode:
+- nvidia,pwm-period-nanoseconds: period of PWM square wave in nanoseconds.
+- nvidia,pwm-tristate-microvolts: Regulator voltage in micro volts when PWM
+  control is disabled and the PWM output is tristated. Note that this voltage is
+  configured in hardware, typically via a resistor divider.
+- nvidia,pwm-min-microvolts: Regulator voltage in micro volts when PWM control
+  is enabled and PWM output is low. Hence, this is the minimum output voltage
+  that the regulator supports when PWM control is enabled.
+- nvidia,pwm-voltage-step-microvolts: Voltage increase in micro volts
+  corresponding to a 1/33th increase in duty cycle. Eg the voltage for 2/33th
+  duty cycle would be: nvidia,pwm-min-microvolts +
+  nvidia,pwm-voltage-step-microvolts * 2.
+- pinctrl-0: I/O pad configuration when PWM control is enabled.
+- pinctrl-1: I/O pad configuration when PWM control is disabled.
+- pinctrl-names: must include the following entries:
+  - dvfs_pwm_enable: I/O pad configuration when PWM control is enabled.
+  - dvfs_pwm_disable: I/O pad configuration when PWM control is disabled.
+
+Example for I2C:
 
 clock@70110000 {
         compatible = "nvidia,tegra124-dfll";
@@ -76,3 +96,58 @@  clock@70110000 {
 
         nvidia,i2c-fs-rate = <400000>;
 };
+
+Example for PWM:
+
+clock@70110000 {
+	compatible = "nvidia,tegra124-dfll";
+	reg = <0 0x70110000 0 0x100>, /* DFLL control */
+	      <0 0x70110000 0 0x100>, /* I2C output control */
+	      <0 0x70110100 0 0x100>, /* Integrated I2C controller */
+	      <0 0x70110200 0 0x100>; /* Look-up table RAM */
+	interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&tegra_car TEGRA210_CLK_DFLL_SOC>,
+	         <&tegra_car TEGRA210_CLK_DFLL_REF>,
+		 <&tegra_car TEGRA124_CLK_I2C5>;;
+	clock-names = "soc", "ref", "i2c";
+	resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>;
+	reset-names = "dvco";
+	#clock-cells = <0>;
+	clock-output-names = "dfllCPU_out";
+
+	nvidia,sample-rate = <25000>;
+	nvidia,droop-ctrl = <0x00000f00>;
+	nvidia,force-mode = <1>;
+	nvidia,cf = <6>;
+	nvidia,ci = <0>;
+	nvidia,cg = <2>;
+
+	nvidia,pwm-min-microvolts = <708000>; /* 708mV */
+	nvidia,pwm-period-nanoseconds = <2500>; /* 2.5us */
+	nvidia,pwm-to-pmic;
+	nvidia,pwm-tristate-microvolts = <1000000>;
+	nvidia,pwm-voltage-step-microvolts = <19200>; /* 19.2mV */
+
+	pinctrl-names = "dvfs_pwm_enable", "dvfs_pwm_disable";
+	pinctrl-0 = <&dvfs_pwm_active_state>;
+	pinctrl-1 = <&dvfs_pwm_inactive_state>;
+};
+
+/* pinmux nodes added for completeness. Binding doc can be found in:
+ * Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
+ */
+
+pinmux: pinmux@700008d4 {
+	dvfs_pwm_active_state: dvfs_pwm_active {
+		dvfs_pwm_pbb1 {
+			nvidia,pins = "dvfs_pwm_pbb1";
+			nvidia,tristate = <TEGRA_PIN_DISABLE>;
+		};
+	};
+	dvfs_pwm_inactive_state: dvfs_pwm_inactive {
+		dvfs_pwm_pbb1 {
+			nvidia,pins = "dvfs_pwm_pbb1";
+			nvidia,tristate = <TEGRA_PIN_ENABLE>;
+		};
+	};
+};