[00/14] MIPS: Fixes and improvements for CI20 board (JZ4780)
mbox series

Message ID cover.1581457290.git.hns@goldelico.com
Headers show
Series
  • MIPS: Fixes and improvements for CI20 board (JZ4780)
Related show

Message

H. Nikolaus Schaller Feb. 11, 2020, 9:41 p.m. UTC
This patch set provides several improvements for the CI20 board:

* suppress warnings from i2c if device is not responding
* make ingenic-drm found through DT
* allow davicom dm9000 ethernet controller to use MAC address provided by U-Boot
* fix #include in jz4780.dtsi
* configure for loadable kernel modules
* add DTS for IR sensor and SW1 button
* configure so that LEDs, IR sensor, SW1 button have drivers
* fix DTS for ACT8600 PMU and configure driver
* fix interrupt of nxp,pcf8563

There is another patch set in our queue to add HDMI support on top of this work.

Signed-off-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>


Alex Smith (1):
  MIPS: DTS: CI20: add DT node for IR sensor

H. Nikolaus Schaller (13):
  i2c: jz4780: suppress txabrt reports for i2cdetect
  drm: ingenic-drm: add MODULE_DEVICE_TABLE
  net: davicom: dm9000: allow to pass MAC address through mac_addr
    module parameter
  MIPS: DTS: jz4780: fix #includes for irq.h and gpio.h
  MIPS: CI20: defconfig: configure for supporting modules
  MIPS: CI20: defconfig: compile leds-gpio driver into the kernel and
    configure for LED triggers
  MIPS: DTS: CI20: fix PMU definitions for ACT8600
  MIPS: CI20: defconfig: configure CONFIG_REGULATOR_ACT8865 for PMU
  MIPS: DTS: CI20: give eth0_power a defined voltage.
  MIPS: CI20: defconfig: compile gpio-ir driver
  MIPS: DTS: CI20: add DT node for SW1 as Enter button
  MIPS: CI20: defconfig: configure for CONFIG_KEYBOARD_GPIO=m
  MIPS: DTS: CI20: fix interrupt for pcf8563 RTC

 arch/mips/boot/dts/ingenic/ci20.dts    | 71 ++++++++++++++++++++------
 arch/mips/boot/dts/ingenic/jz4780.dtsi |  2 +
 arch/mips/configs/ci20_defconfig       | 21 ++++++++
 drivers/gpu/drm/ingenic/ingenic-drm.c  |  2 +
 drivers/i2c/busses/i2c-jz4780.c        |  3 ++
 drivers/net/ethernet/davicom/dm9000.c  | 42 +++++++++++++++
 6 files changed, 125 insertions(+), 16 deletions(-)

Comments

Andreas Kemnade Feb. 11, 2020, 9:48 p.m. UTC | #1
On Tue, 11 Feb 2020 22:41:24 +0100
"H. Nikolaus Schaller" <hns@goldelico.com> wrote:

> There is a ACT8600 on the CI20 board and the bindings of the
> ACT8865 driver have changed without updating the CI20 device
> tree. Therefore the PMU can not be probed successfully and
> is running in power-on reset state.
> 
> Fix DT to match the latest act8865-regulator bindings.
> 
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
hmm, what about a Fixes: tag here? Sounds like a regression.

Regards,
Andreas