===================================================================
@@ -23,6 +23,8 @@
#include <linux/init.h>
#include <linux/vt_kern.h>
#include <linux/platform_device.h>
+#include <linux/adb.h>
+#include <linux/cuda.h>
#define BOOTINFO_COMPAT_1_0
#include <asm/setup.h>
@@ -889,6 +891,10 @@ static void __init mac_identify(void)
oss_init();
psc_init();
baboon_init();
+
+#ifdef CONFIG_ADB_CUDA
+ find_via_cuda();
+#endif
}
static void __init mac_report_hardware(void)
===================================================================
@@ -117,7 +117,33 @@ struct adb_driver via_cuda_driver = {
};
#endif /* CONFIG_ADB */
-#ifdef CONFIG_PPC
+#ifdef CONFIG_MAC
+int __init find_via_cuda(void)
+{
+ struct adb_request req;
+ int err;
+
+ if (macintosh_config->adb_type != MAC_ADB_CUDA)
+ return 0;
+
+ via = via1;
+ cuda_state = idle;
+
+ err = cuda_init_via();
+ if (err) {
+ printk(KERN_ERR "cuda_init_via() failed\n");
+ via = NULL;
+ return 0;
+ }
+
+ /* enable autopoll */
+ cuda_request(&req, NULL, 3, CUDA_PACKET, CUDA_AUTOPOLL, 1);
+ while (!req.complete)
+ cuda_poll();
+
+ return 1;
+}
+#else
int __init find_via_cuda(void)
{
struct adb_request req;
@@ -175,7 +201,7 @@ int __init find_via_cuda(void)
vias = NULL;
return 0;
}
-#endif /* CONFIG_PPC */
+#endif /* !defined CONFIG_MAC */
static int __init via_cuda_start(void)
{
@@ -184,14 +210,14 @@ static int __init via_cuda_start(void)
#ifdef CONFIG_MAC
cuda_irq = IRQ_MAC_ADB;
-#else /* CONFIG_MAC */
+#else
cuda_irq = irq_of_parse_and_map(vias, 0);
if (cuda_irq == NO_IRQ) {
printk(KERN_ERR "via-cuda: can't map interrupts for %s\n",
vias->full_name);
return -ENODEV;
}
-#endif /* CONFIG_MAC */
+#endif
if (request_irq(cuda_irq, cuda_interrupt, 0, "ADB", cuda_interrupt)) {
printk(KERN_ERR "via-cuda: can't request irq %d\n", cuda_irq);
@@ -216,7 +242,6 @@ cuda_probe(void)
#else
if (macintosh_config->adb_type != MAC_ADB_CUDA)
return -ENODEV;
- via = via1;
#endif
return 0;
}
@@ -224,20 +249,9 @@ cuda_probe(void)
static int __init
cuda_init(void)
{
-#ifdef CONFIG_PPC
if (via == NULL)
return -ENODEV;
return 0;
-#else
- int err = cuda_init_via();
- if (err) {
- printk(KERN_ERR "cuda_init_via() failed\n");
- return -ENODEV;
- }
- out_8(&via[IER], IER_SET|SR_INT); /* enable interrupt from SR */
-
- return via_cuda_start();
-#endif
}
#endif /* CONFIG_ADB */
@@ -430,9 +444,12 @@ cuda_poll(void)
/* cuda_interrupt only takes a normal lock, we disable
* interrupts here to avoid re-entering and thus deadlocking.
*/
- disable_irq(cuda_irq);
- cuda_interrupt(0, NULL);
- enable_irq(cuda_irq);
+ if (cuda_fully_inited) {
+ disable_irq(cuda_irq);
+ cuda_interrupt(0, NULL);
+ enable_irq(cuda_irq);
+ } else
+ cuda_interrupt(0, NULL);
}
static irqreturn_t
@@ -446,7 +463,7 @@ cuda_interrupt(int irq, void *arg)
spin_lock(&cuda_lock);
- /* On powermacs, this handler is registered for the VIA IRQ. But it uses
+ /* On powermacs, this handler is registered for the VIA IRQ. But they use
* just the shift register IRQ -- other VIA interrupt sources are disabled.
* On m68k macs, the VIA IRQ sources are dispatched individually. Unless
* we are polling, the shift register IRQ flag has already been cleared.
The valkyriefb driver needs the CUDA to work in order to set the video mode at boot. Initialising the device earlier, and bring the m68k code closer to the powermac code. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> --- arch/m68k/mac/config.c | 6 ++++ drivers/macintosh/via-cuda.c | 57 +++++++++++++++++++++++++++---------------- 2 files changed, 43 insertions(+), 20 deletions(-)