diff mbox

[U-Boot,2/2] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board

Message ID 1378299618-29799-2-git-send-email-alban.bedel@avionic-design.de
State Changes Requested
Delegated to: Tom Warren
Headers show

Commit Message

Alban Bedel Sept. 4, 2013, 1 p.m. UTC 
Add support for the new Tamonten™ NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
 .../common/pinmux-config-tamonten-ng.h             | 385 +++++++++++++++++++++
 board/avionic-design/common/tamonten-ng.c          | 129 +++++++
 board/avionic-design/dts/tegra30-tamonten.dtsi     |  74 ++++
 board/avionic-design/dts/tegra30-tec-ng.dts        |   8 +
 board/avionic-design/tec-ng/Makefile               |  32 ++
 boards.cfg                                         |   1 +
 include/configs/tec-ng.h                           |  84 +++++
 7 files changed, 713 insertions(+)
 create mode 100644 board/avionic-design/common/pinmux-config-tamonten-ng.h
 create mode 100644 board/avionic-design/common/tamonten-ng.c
 create mode 100644 board/avionic-design/dts/tegra30-tamonten.dtsi
 create mode 100644 board/avionic-design/dts/tegra30-tec-ng.dts
 create mode 100644 board/avionic-design/tec-ng/Makefile
 create mode 100644 include/configs/tec-ng.h

Comments

Stephen Warren Sept. 4, 2013, 6:05 p.m. UTC | #1 
On 09/04/2013 07:00 AM, Alban Bedel wrote:
> Add support for the new Tamonten™ NG platform from Avionic Design. 
> Currently only I2C, MMC, USB and ethernet have been tested.

(Also CC'ing the Tegra maintainer here)

> diff --git a/board/avionic-design/common/tamonten-ng.c
> b/board/avionic-design/common/tamonten-ng.c

> +void pmu_write(uchar reg, uchar data) +{ +	int i; +
> i2c_set_bus_num(0);	/* PMU is on bus 0 */ +	for (i = 0; i <
> MAX_I2C_RETRY; ++i) { +		if (i2c_write(PMU_I2C_ADDRESS, reg, 1,
> &data, 1)) +			udelay(100); +		else +			break; +	} +}

Is there really a need to retry the I2C transactions? If so, why do
they fail? I assume this was just copy/pasted from some other board
file, and there's no need for any retries?

It'd be nice if there was a proper PMU subsystem, so we could have a
specific driver for each PMU chip, rather than having
open-coded/custom writes to the PMU registers in each board file, but
I guess that's not an issue with this patch specfically.

> diff --git a/include/configs/tec-ng.h b/include/configs/tec-ng.h

> +/* support the new (FDT-based) image format */ +#define
> CONFIG_FIT

Hmmm. Do the standard Tegra boot scripts in tegra-common-post.h deal
well with FIT? I've tried to avoid FIT usage as much as possible.
Alban Bedel Sept. 5, 2013, 12:46 p.m. UTC | #2 
On Wed, 04 Sep 2013 12:05:00 -0600
Stephen Warren <swarren@wwwdotorg.org> wrote:

> On 09/04/2013 07:00 AM, Alban Bedel wrote:
> > Add support for the new Tamonten™ NG platform from Avionic Design. 
> > Currently only I2C, MMC, USB and ethernet have been tested.
> 
> (Also CC'ing the Tegra maintainer here)

Ok, I'll add him in the next patch round.

> > diff --git a/board/avionic-design/common/tamonten-ng.c
> > b/board/avionic-design/common/tamonten-ng.c
> >
> > +void pmu_write(uchar reg, uchar data)
> > +{
> > +	int i;
> > +   i2c_set_bus_num(0);	/* PMU is on bus 0 */
> > +	for (i = 0; i < MAX_I2C_RETRY; ++i) {
> > +		if (i2c_write(PMU_I2C_ADDRESS, reg, 1, &data, 1))
> > +			udelay(100);
> > +		else
> > +			break;
> > +	}
> > +}
> 
> Is there really a need to retry the I2C transactions? If so, why do
> they fail? I assume this was just copy/pasted from some other board
> file, and there's no need for any retries?

Yes, that was adapted from the cardhu code and the retry are most
probably useless. I just made a bit more generic function because
we have to set several outputs, on cardhu only one is set.

> It'd be nice if there was a proper PMU subsystem, so we could have a
> specific driver for each PMU chip, rather than having
> open-coded/custom writes to the PMU registers in each board file, but
> I guess that's not an issue with this patch specfically.

A PMU subsystem would be nice, although something that would be
compatible with the Linux regulator and their representation in DT
would be even better.

Otherwise a first step could be to at least create a driver for this
PMU, similar to one for tps6586x. That would at least prevent too much
code duplication between the T30 boards.

> > diff --git a/include/configs/tec-ng.h b/include/configs/tec-ng.h
> >
> > +/* support the new (FDT-based) image format */
> > +#define CONFIG_FIT
> 
> Hmmm. Do the standard Tegra boot scripts in tegra-common-post.h deal
> well with FIT? I've tried to avoid FIT usage as much as possible.

AFAIU it doesn't change anything if you use old images, it just allow
you to also use FIT image. As the build system we use for our platform
produce FIT image we do need support for it. Or should such things,
which are not related to the HW config, be configured in another place?

Alban
Stephen Warren Sept. 5, 2013, 7:15 p.m. UTC | #3 
On 09/05/2013 06:46 AM, Alban Bedel wrote:
> On Wed, 04 Sep 2013 12:05:00 -0600
> Stephen Warren <swarren@wwwdotorg.org> wrote:
>> On 09/04/2013 07:00 AM, Alban Bedel wrote:
>>> Add support for the new Tamonten™ NG platform from Avionic Design. 
>>> Currently only I2C, MMC, USB and ethernet have been tested.
...
>>> diff --git a/include/configs/tec-ng.h b/include/configs/tec-ng.h
>>>
>>> +/* support the new (FDT-based) image format */
>>> +#define CONFIG_FIT
>>
>> Hmmm. Do the standard Tegra boot scripts in tegra-common-post.h deal
>> well with FIT? I've tried to avoid FIT usage as much as possible.
> 
> AFAIU it doesn't change anything if you use old images, it just allow
> you to also use FIT image. As the build system we use for our platform
> produce FIT image we do need support for it. Or should such things,
> which are not related to the HW config, be configured in another place?

No, this file is the right/only place for such things.
diff mbox

Patch

diff --git a/board/avionic-design/common/pinmux-config-tamonten-ng.h b/board/avionic-design/common/pinmux-config-tamonten-ng.h
new file mode 100644
index 0000000..39df731
--- /dev/null
+++ b/board/avionic-design/common/pinmux-config-tamonten-ng.h
@@ -0,0 +1,385 @@ 
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _PINMUX_CONFIG_TAMONTEN_NG_H_
+#define _PINMUX_CONFIG_TAMONTEN_NG_H_
+
+#define DEFAULT_PINMUX(_pingroup, _mux, _pull, _tri, _io)	\
+	{							\
+		.pingroup	= PINGRP_##_pingroup,		\
+		.func		= PMUX_FUNC_##_mux,		\
+		.pull		= PMUX_PULL_##_pull,		\
+		.tristate	= PMUX_TRI_##_tri,		\
+		.io		= PMUX_PIN_##_io,		\
+		.lock		= PMUX_PIN_LOCK_DEFAULT,	\
+		.od		= PMUX_PIN_OD_DEFAULT,		\
+		.ioreset	= PMUX_PIN_IO_RESET_DEFAULT,	\
+	}
+
+#define I2C_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _od) \
+	{							\
+		.pingroup	= PINGRP_##_pingroup,		\
+		.func		= PMUX_FUNC_##_mux,		\
+		.pull		= PMUX_PULL_##_pull,		\
+		.tristate	= PMUX_TRI_##_tri,		\
+		.io		= PMUX_PIN_##_io,		\
+		.lock		= PMUX_PIN_LOCK_##_lock,	\
+		.od		= PMUX_PIN_OD_##_od,		\
+		.ioreset	= PMUX_PIN_IO_RESET_DEFAULT,	\
+	}
+
+#define LV_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _ioreset) \
+	{							\
+		.pingroup	= PINGRP_##_pingroup,		\
+		.func		= PMUX_FUNC_##_mux,		\
+		.pull		= PMUX_PULL_##_pull,		\
+		.tristate	= PMUX_TRI_##_tri,		\
+		.io		= PMUX_PIN_##_io,		\
+		.lock		= PMUX_PIN_LOCK_##_lock,	\
+		.od		= PMUX_PIN_OD_DEFAULT,		\
+		.ioreset	= PMUX_PIN_IO_RESET_##_ioreset	\
+	}
+
+#define DEFAULT_PADCFG(_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) \
+	{							\
+		.padgrp		= PDRIVE_PINGROUP_##_padgrp,	\
+		.slwf		= _slwf,			\
+		.slwr		= _slwr,			\
+		.drvup		= _drvup,			\
+		.drvdn		= _drvdn,			\
+		.lpmd		= PGRP_LPMD_##_lpmd,		\
+		.schmt		= PGRP_SCHMT_##_schmt,		\
+		.hsm		= PGRP_HSM_##_hsm,		\
+	}
+
+static struct pingroup_config tamonten_ng_pinmux_common[] = {
+	/* SDMMC1 pinmux */
+	DEFAULT_PINMUX(SDMMC1_CLK,  SDMMC1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC1_CMD,  SDMMC1, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC1_DAT0, SDMMC1, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC1_DAT1, SDMMC1, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC1_DAT2, SDMMC1, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC1_DAT3, SDMMC1, UP,     NORMAL, INPUT),
+
+	/* SDMMC3 pinmux */
+	DEFAULT_PINMUX(SDMMC3_CLK,  SDMMC3, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC3_CMD,  SDMMC3, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC3_DAT0, SDMMC3, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC3_DAT1, SDMMC3, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC3_DAT2, SDMMC3, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC3_DAT3, SDMMC3, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC3_DAT4, SDMMC3, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC3_DAT5, SDMMC3, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC3_DAT6, SDMMC3, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SDMMC3_DAT7, SDMMC3, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(GMI_IORDY,   RSVD1,  UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(GMI_CS6_N,   RSVD1,  UP,     NORMAL, INPUT),
+
+	/* SDMMC4 pinmux */
+	LV_PINMUX(SDMMC4_CLK,   SDMMC4, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_CMD,   SDMMC4, UP,     NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_DAT0,  SDMMC4, UP,     NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_DAT1,  SDMMC4, UP,     NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_DAT2,  SDMMC4, UP,     NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_DAT3,  SDMMC4, UP,     NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_DAT4,  SDMMC4, UP,     NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_DAT5,  SDMMC4, UP,     NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_DAT6,  SDMMC4, UP,     NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_DAT7,  SDMMC4, UP,     NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(SDMMC4_RST_N, RSVD1,  DOWN,   NORMAL, INPUT, DISABLE, DISABLE),
+
+	/* I2C1 pinmux */
+	I2C_PINMUX(GEN1_I2C_SCL, I2C1, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+	I2C_PINMUX(GEN1_I2C_SDA, I2C1, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+	/* I2C2 pinmux */
+	I2C_PINMUX(GEN2_I2C_SCL, I2C2, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+	I2C_PINMUX(GEN2_I2C_SDA, I2C2, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+	/* I2C3 pinmux */
+	I2C_PINMUX(CAM_I2C_SCL, I2C3, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+	I2C_PINMUX(CAM_I2C_SDA, I2C3, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+	/* I2C4 pinmux */
+	I2C_PINMUX(DDC_SCL, I2C4, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+	I2C_PINMUX(DDC_SDA, I2C4, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+	/* Power I2C pinmux */
+	I2C_PINMUX(PWR_I2C_SCL, I2CPWR, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+	I2C_PINMUX(PWR_I2C_SDA, I2CPWR, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+	/* UART1 */
+	DEFAULT_PINMUX(ULPI_DATA0, UARTA, NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(ULPI_DATA1, UARTA, NORMAL, NORMAL, INPUT),
+
+	/* UART2 */
+	DEFAULT_PINMUX(UART2_RXD,   UARTB, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(UART2_TXD,   UARTB, NORMAL, NORMAL, OUTPUT),
+
+	/* UART3 */
+	DEFAULT_PINMUX(UART3_TXD,   UARTC, NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(UART3_RXD,   UARTC, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(UART3_CTS_N, UARTC, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(UART3_RTS_N, UARTC, NORMAL, NORMAL, OUTPUT),
+
+	/* UART4 */
+	DEFAULT_PINMUX(ULPI_CLK, UARTD, NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(ULPI_DIR, UARTD, UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(ULPI_NXT, UARTD, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(ULPI_STP, UARTD, NORMAL, NORMAL, OUTPUT),
+
+	/* DAP */
+	DEFAULT_PINMUX(CLK1_OUT, EXTPERIPH1, NORMAL, NORMAL, INPUT),
+
+	/* I2S1 */
+	DEFAULT_PINMUX(DAP2_FS,   I2S1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(DAP2_DIN,  I2S1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(DAP2_DOUT, I2S1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(DAP2_SCLK, I2S1, NORMAL, NORMAL, INPUT),
+
+	/* SPDIF */
+	DEFAULT_PINMUX(SPDIF_IN,  SPDIF, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(SPDIF_OUT, SPDIF, NORMAL, NORMAL, OUTPUT),
+
+	/* I2S2 */
+	DEFAULT_PINMUX(DAP3_FS,   I2S2, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(DAP3_DIN,  I2S2, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(DAP3_DOUT, I2S2, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(DAP3_SCLK, I2S2, NORMAL, NORMAL, INPUT),
+
+	/* DAP4 */
+	DEFAULT_PINMUX(DAP4_FS,   I2S3, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(DAP4_DIN,  I2S3, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(DAP4_SCLK, I2S3, NORMAL, NORMAL, INPUT),
+
+	/* Tamonten GPIO */
+	DEFAULT_PINMUX(GPIO_PV2,   RSVD1, NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(GPIO_PV3,   RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(SPI2_CS1_N, RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* LCD */
+	DEFAULT_PINMUX(LCD_PWR1,  DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_PWR2,  DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_SDIN,  DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_SDOUT, DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_WR_N,  DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_CS0_N, DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_DC0,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_SCK,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_PWR0,  DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_PCLK,  DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_DE,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_HSYNC, DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_VSYNC, DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D0,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D1,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D2,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D3,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D4,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D5,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D6,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D7,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D8,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D9,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D10,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D11,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D12,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D13,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D14,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D15,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D16,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D17,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D18,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D19,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D20,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D21,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D22,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_D23,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_CS1_N, DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_M1,    DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(LCD_DC1,   DISPA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(CRT_HSYNC, CRT,   NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(CRT_VSYNC, CRT,   NORMAL, NORMAL, OUTPUT),
+
+	/* BT656 */
+	LV_PINMUX(VI_MCLK,  VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_PCLK,  VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_HSYNC, VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_VSYNC, VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D2,    VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D3,    VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D4,    VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D5,    VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D6,    VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D7,    VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D8,    VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D9,    VI,    NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D11,   RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+
+	/* GPIOs */
+	DEFAULT_PINMUX(GPIO_PU5, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PU6, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GMI_AD12, RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* LCD BL */
+	DEFAULT_PINMUX(GMI_AD8,  PWM0,  NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(GMI_AD10, RSVD4, NORMAL, NORMAL, OUTPUT),
+
+	/* SPI4 */
+	DEFAULT_PINMUX(GMI_A16, SPI4, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GMI_A17, SPI4, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GMI_A18, SPI4, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GMI_A19, SPI4, NORMAL, NORMAL, INPUT),
+
+	/* Video input GPIO */
+	DEFAULT_PINMUX(GPIO_PCC1, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PBB0, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PBB7, RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* Sensor GPIO */
+	DEFAULT_PINMUX(GPIO_PCC2, RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* JTAG */
+	DEFAULT_PINMUX(JTAG_RTCK, RTCK, NORMAL, NORMAL, OUTPUT),
+
+	/* Power controls */
+	DEFAULT_PINMUX(GMI_CS2_N, RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* SPI1 */
+	DEFAULT_PINMUX(SPI1_MOSI,  SPI1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(SPI1_SCK,   SPI1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(SPI1_CS0_N, SPI1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(SPI1_MISO,  SPI1, NORMAL, NORMAL, INPUT),
+
+	/* PMU */
+	DEFAULT_PINMUX(GPIO_PV0,    RSVD1,  UP,     NORMAL, INPUT),
+	DEFAULT_PINMUX(SYS_CLK_REQ, SYSCLK, NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(CLK_32K_IN,  SYSCLK, NORMAL, NORMAL, INPUT),
+
+	/* PCI */
+	DEFAULT_PINMUX(PEX_L0_PRSNT_N,  PCIE, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_L0_RST_N,    PCIE, NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(PEX_L0_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_WAKE_N,      PCIE, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_L1_PRSNT_N,  PCIE, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_L1_RST_N,    PCIE, NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(PEX_L1_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_L2_PRSNT_N,  PCIE, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(PEX_L2_RST_N,    PCIE, NORMAL, NORMAL, OUTPUT),
+	DEFAULT_PINMUX(PEX_L2_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+
+	/* HDMI */
+	DEFAULT_PINMUX(HDMI_CEC, CEC,   NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(HDMI_INT, RSVD1, NORMAL, TRISTATE, INPUT),
+};
+
+static struct pingroup_config unused_pins_lowpower[] = {
+	/* UART1 - NC */
+	DEFAULT_PINMUX(ULPI_DATA2, UARTA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(ULPI_DATA3, UARTA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(ULPI_DATA4, UARTA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(ULPI_DATA5, UARTA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(ULPI_DATA6, UARTA, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(ULPI_DATA7, UARTA, NORMAL, NORMAL, INPUT),
+
+	/* UART2 - NC */
+	DEFAULT_PINMUX(UART2_RTS_N, UARTB, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(UART2_CTS_N, UARTB, NORMAL, NORMAL, INPUT),
+
+	/* DAP - NC */
+	DEFAULT_PINMUX(CLK1_REQ,  RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(CLK3_OUT,  RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(CLK3_REQ,  RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* DAP4 - NC */
+	DEFAULT_PINMUX(DAP4_DOUT, I2S3, NORMAL, NORMAL, INPUT),
+
+	/* Tamonten GPIO - NC */
+	DEFAULT_PINMUX(CLK2_OUT, EXTPERIPH2, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(CLK2_REQ, DAP,        NORMAL, NORMAL, INPUT),
+
+	/* BT656 - NC */
+	LV_PINMUX(VI_D0,  RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D1,  RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+	LV_PINMUX(VI_D10, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+
+	/* GPIO - NC */
+	DEFAULT_PINMUX(GPIO_PU0, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PU1, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PU2, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PU3, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PU4, RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* Video input - NC */
+	DEFAULT_PINMUX(CAM_MCLK,  RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PBB3, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PBB5, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PBB6, RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW11,  RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* KBC keys - NC */
+	DEFAULT_PINMUX(KB_ROW0,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW1,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW2,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW3,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW4,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW5,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW6,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW7,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW8,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW9,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW10, KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW12, KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW13, KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW14, KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_ROW15, KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_COL0,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_COL1,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_COL2,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_COL3,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_COL4,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_COL5,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_COL6,  KBC, UP, NORMAL, INPUT),
+	DEFAULT_PINMUX(KB_COL7,  KBC, UP, NORMAL, INPUT),
+
+	/* PMU - NC */
+	DEFAULT_PINMUX(CLK_32K_OUT, RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* Power rails GPIO - NC */
+	DEFAULT_PINMUX(SPI2_SCK,  RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PBB4, RSVD1, NORMAL, NORMAL, INPUT),
+
+	/* Others - NC */
+	DEFAULT_PINMUX(GMI_WP_N,   RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GPIO_PV1,   RSVD1, NORMAL, NORMAL, INPUT),
+	DEFAULT_PINMUX(GMI_WAIT,   NAND, UP,     TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_ADV_N,  NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_CLK,    NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_CS3_N,  NAND, NORMAL, NORMAL,   OUTPUT),
+	DEFAULT_PINMUX(GMI_CS7_N,  NAND, UP,     NORMAL,   INPUT),
+	DEFAULT_PINMUX(GMI_AD0,    NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_AD1,    NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_AD2,    NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_AD3,    NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_AD4,    NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_AD5,    NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_AD6,    NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_AD7,    NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_AD9,    PWM1, NORMAL, NORMAL,   OUTPUT),
+	DEFAULT_PINMUX(GMI_AD11,   NAND, NORMAL, NORMAL,   OUTPUT),
+	DEFAULT_PINMUX(GMI_AD13,   NAND, UP,     NORMAL,   INPUT),
+	DEFAULT_PINMUX(GMI_WR_N,   NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_OE_N,   NAND, NORMAL, TRISTATE, OUTPUT),
+	DEFAULT_PINMUX(GMI_DQS,    NAND, NORMAL, TRISTATE, OUTPUT),
+};
+
+static struct padctrl_config tamonten_ng_padctrl[] = {
+	/* (_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) */
+	DEFAULT_PADCFG(SDIO1, SDIOCFG_DRVUP_SLWF, SDIOCFG_DRVDN_SLWR,
+		SDIOCFG_DRVUP, SDIOCFG_DRVDN, NONE, DISABLE, DISABLE),
+};
+#endif	/* _PINMUX_CONFIG_TAMONTEN_NG_H_ */
diff --git a/board/avionic-design/common/tamonten-ng.c b/board/avionic-design/common/tamonten-ng.c
new file mode 100644
index 0000000..7a17839
--- /dev/null
+++ b/board/avionic-design/common/tamonten-ng.c
@@ -0,0 +1,129 @@ 
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/gp_padctrl.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+#include "pinmux-config-tamonten-ng.h"
+#include <i2c.h>
+
+#define PMU_I2C_ADDRESS		0x2D
+#define MAX_I2C_RETRY		3
+
+#define PMU_REG_LDO1		0x30
+#define PMU_REG_LDO2		0x31
+#define PMU_REG_LDO5		0x32
+#define PMU_REG_LDO8		0x33
+#define PMU_REG_LDO7		0x34
+#define PMU_REG_LDO6		0x35
+#define PMU_REG_LDO4		0x36
+#define PMU_REG_LDO3		0x37
+
+#define PMU_REG_LDO_OFF		0
+#define PMU_REG_LDO_HIGH_POWER	1
+#define PMU_REG_LDO_LOW_POWER	3
+
+/* Voltage selection for the LDOs with 50mV resolution */
+#define PMU_REG_LDO_SEL_50(mV)	((((mV - 1000) / 50) + 4) << 2)
+/* Voltage selection for the LDOs with 100mV resolution */
+#define PMU_REG_LDO_SEL_100(mV)	((((mV - 1000) / 100) + 2) << 2)
+
+#define PMU_REG_LDO_50(st, mV)	(PMU_REG_LDO_##st | PMU_REG_LDO_SEL_50(mV))
+#define PMU_REG_LDO_100(st, mV)	(PMU_REG_LDO_##st | PMU_REG_LDO_SEL_50(mV))
+
+#define PMU_LDO1(st, mV)	PMU_REG_LDO_50(st, mV)
+#define PMU_LDO2(st, mV)	PMU_REG_LDO_50(st, mV)
+#define PMU_LDO5(st, mV)	PMU_REG_LDO_100(st, mV)
+#define PMU_LDO8(st, mV)	PMU_REG_LDO_100(st, mV)
+#define PMU_LDO7(st, mV)	PMU_REG_LDO_100(st, mV)
+#define PMU_LDO6(st, mV)	PMU_REG_LDO_100(st, mV)
+#define PMU_LDO4(st, mV)	PMU_REG_LDO_50(st, mV)
+#define PMU_LDO3(st, mV)	PMU_REG_LDO_100(st, mV)
+
+void pinmux_init(void)
+{
+	pinmux_config_table(tamonten_ng_pinmux_common,
+			    ARRAY_SIZE(tamonten_ng_pinmux_common));
+	pinmux_config_table(unused_pins_lowpower,
+			    ARRAY_SIZE(unused_pins_lowpower));
+
+	/* Initialize any non-default pad configs (APB_MISC_GP regs) */
+	padgrp_config_table(tamonten_ng_padctrl,
+			    ARRAY_SIZE(tamonten_ng_padctrl));
+}
+
+
+void pmu_write(uchar reg, uchar data)
+{
+	int i;
+	i2c_set_bus_num(0);	/* PMU is on bus 0 */
+	for (i = 0; i < MAX_I2C_RETRY; ++i) {
+		if (i2c_write(PMU_I2C_ADDRESS, reg, 1, &data, 1))
+			udelay(100);
+		else
+			break;
+	}
+}
+
+void power_init_board(void)
+{
+	/* Set the periphs in reset */
+	gpio_request(GPIO_PI4, "nRST_PERIPH");
+	gpio_direction_output(GPIO_PI4, 0);
+
+	/* Disable the PCIe power */
+	gpio_request(GPIO_PT3, "EN_3V3_PEX_HVDD");
+	gpio_direction_output(GPIO_PT3, 0);
+
+	/* Disable the SATA power */
+	gpio_request(GPIO_PK3, "EN_3V3_SATA_HVDD");
+	gpio_direction_output(GPIO_PK3, 0);
+
+	/* Disable LDO1 for PCIe and SATA */
+	pmu_write(PMU_REG_LDO1, PMU_LDO1(OFF, 1050));
+
+	/* Turn on the alive signal */
+	gpio_request(GPIO_PV2, "ALIVE");
+	gpio_direction_output(GPIO_PV2, 1);
+
+	/* Wait for the periph to finish their reset */
+	udelay(1000);
+	gpio_direction_output(GPIO_PI4, 1);
+}
+
+#if defined(CONFIG_TEGRA_MMC)
+/*
+ * Do I2C/PMU writes to bring up SD card bus power
+ *
+ */
+void board_sdmmc_voltage_init(void)
+{
+	/* Enable LDO5 with 3.3v for SDMMC3 */
+	pmu_write(PMU_REG_LDO5, PMU_LDO5(HIGH_POWER, 3300));
+
+	/* Switch the power on */
+	gpio_request(GPIO_PJ2, "EN_3V3_EMMC");
+	gpio_direction_output(GPIO_PJ2, 1);
+}
+
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the MMC muxes, power rails, etc.
+ */
+void pin_mux_mmc(void)
+{
+	/*
+	 * NOTE: We don't do mmc-specific pin muxes here.
+	 * They were done globally in pinmux_init().
+	 */
+
+	/* Bring up the SDIO1 power rail */
+	board_sdmmc_voltage_init();
+}
+#endif	/* MMC */
diff --git a/board/avionic-design/dts/tegra30-tamonten.dtsi b/board/avionic-design/dts/tegra30-tamonten.dtsi
new file mode 100644
index 0000000..d80b177
--- /dev/null
+++ b/board/avionic-design/dts/tegra30-tamonten.dtsi
@@ -0,0 +1,74 @@ 
+#include "tegra30.dtsi"
+
+/ {
+	model = "Avionic Design Tamonten NG";
+	compatible = "ad,tamonten-ng", "nvidia,tegra30";
+
+	memory {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	aliases {
+		i2c0 = "/i2c@7000d000";
+		i2c1 = "/i2c@7000c000";
+		i2c2 = "/i2c@7000c400";
+		i2c3 = "/i2c@7000c500";
+		i2c4 = "/i2c@7000c700";
+		sdhci0 = "/sdhci@78000600";
+		sdhci1 = "/sdhci@78000400";
+		sdhci2 = "/sdhci@78000000";
+		usb0 = "/usb@7d008000";
+	};
+
+	i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	spi@7000da00 {
+		status = "okay";
+		spi-max-frequency = <25000000>;
+	};
+
+	sdhci@78000000 {
+		status = "okay";
+		bus-width = <4>;
+	};
+
+	sdhci@78000400 {
+		status = "okay";
+		cd-gpios = <&gpio 69 1>; /* gpio PI5 */
+		wp-gpios = <&gpio 67 0>; /* gpio PI3 */
+		bus-width = <4>;
+	};
+
+	sdhci@78000600 {
+		status = "okay";
+		bus-width = <8>;
+	};
+
+	usb@7d008000 {
+		status = "okay";
+	};
+
+};
diff --git a/board/avionic-design/dts/tegra30-tec-ng.dts b/board/avionic-design/dts/tegra30-tec-ng.dts
new file mode 100644
index 0000000..244b99d
--- /dev/null
+++ b/board/avionic-design/dts/tegra30-tec-ng.dts
@@ -0,0 +1,8 @@ 
+/dts-v1/;
+
+#include "tegra30-tamonten.dtsi"
+
+/ {
+	model = "Avionic Design Tamonten™ NG Evaluation Carrier";
+	compatible = "ad,tec-ng", "nvidia,tegra30";
+};
diff --git a/board/avionic-design/tec-ng/Makefile b/board/avionic-design/tec-ng/Makefile
new file mode 100644
index 0000000..22e19e0
--- /dev/null
+++ b/board/avionic-design/tec-ng/Makefile
@@ -0,0 +1,32 @@ 
+#
+# (C) Copyright 2013
+# Avionic Design GmbH <www.avionic-design.de>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+$(shell mkdir -p $(obj)../common $(obj)../../nvidia/common)
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y	:= ../common/tamonten-ng.o
+
+include ../../nvidia/common/common.mk
+
+COBJS	:= $(COBJS-y)
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/boards.cfg b/boards.cfg
index be810c7..ff8fa0c 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -374,6 +374,7 @@  jornada                      arm         sa1100
 plutux                       arm         armv7:arm720t plutux            avionic-design tegra20
 medcom-wide                  arm         armv7:arm720t medcom-wide       avionic-design tegra20
 tec                          arm         armv7:arm720t tec               avionic-design tegra20
+tec-ng                       arm         armv7:arm720t tec-ng            avionic-design tegra30
 paz00                        arm         armv7:arm720t paz00             compal         tegra20
 trimslice                    arm         armv7:arm720t trimslice         compulab       tegra20
 atngw100                     avr32       at32ap      -                   atmel          at32ap700x
diff --git a/include/configs/tec-ng.h b/include/configs/tec-ng.h
new file mode 100644
index 0000000..13baa76
--- /dev/null
+++ b/include/configs/tec-ng.h
@@ -0,0 +1,84 @@ 
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "tegra30-common.h"
+
+/* Enable fdt support for tec-ng. Flash the image in u-boot-dtb.bin */
+#define CONFIG_DEFAULT_DEVICE_TREE	tegra30-tec-ng
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+
+/* High-level configuration options */
+#define V_PROMPT			"Tegra30 (TEC-NG) # "
+#define CONFIG_TEGRA_BOARD_STRING	"Avionic Design Tamonten™ NG Evaluation Carrier"
+
+/* Board-specific serial config */
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_TEGRA_ENABLE_UARTD
+#define CONFIG_SYS_NS16550_COM1		NV_PA_APB_UARTD_BASE
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* I2C */
+#define CONFIG_SYS_I2C_TEGRA
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_MAX_I2C_BUS		TEGRA_I2C_NUM_CONTROLLERS
+#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+
+/* SD/MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_TEGRA_MMC
+#define CONFIG_CMD_MMC
+
+/* Environment in eMMC, at the end of 2nd "boot sector" */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET		(-CONFIG_ENV_SIZE)
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_SYS_MMC_ENV_PART		2
+
+/* SPI */
+#define CONFIG_TEGRA20_SLINK
+#define CONFIG_TEGRA_SLINK_CTRLS       6
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED        24000000
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH_SIZE          (4 << 20)
+
+/* USB Host support */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_TEGRA
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_USB
+
+/* USB networking support */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+
+/* General networking support */
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+
+/* Tag support */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+/* support the new (FDT-based) image format */
+#define CONFIG_FIT
+
+#include "tegra-common-post.h"
+
+#endif /* __CONFIG_H */