[V5,1/3] pci: Add PCIe driver for Samsung Exynos

Message ID	000b01ce6839$0f0455d0$2d0d0170$@samsung.com
State	Not Applicable
Headers	show Return-Path: <linux-pci-owner@vger.kernel.org> From: Jingoo Han <jg1.han@samsung.com> To: 'Kukjin Kim' <kgene.kim@samsung.com>, 'Bjorn Helgaas' <bhelgaas@google.com> Cc: linux-samsung-soc@vger.kernel.org, linux-pci@vger.kernel.org, devicetree-discuss@lists.ozlabs.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, 'Grant Likely' <grant.likely@secretlab.ca>, 'Andrew Murray' <andrew.murray@arm.com>, 'Thomas Petazzoni' <thomas.petazzoni@free-electrons.com>, 'Thierry Reding' <thierry.reding@avionic-design.de>, 'Jason Gunthorpe' <jgunthorpe@obsidianresearch.com>, 'Arnd Bergmann' <arnd@arndb.de>, 'Surendranath Gurivireddy Balla' <suren.reddy@samsung.com>, 'Siva Reddy Kallam' <siva.kallam@samsung.com>, 'Thomas Abraham' <thomas.abraham@linaro.org>, Jingoo Han <jg1.han@samsung.com> Subject: [PATCH V5 1/3] pci: Add PCIe driver for Samsung Exynos Date: Thu, 13 Jun 2013 22:22:31 +0900 Message-id: <000b01ce6839$0f0455d0$2d0d0170$@samsung.com> MIME-version: 1.0 Content-type: text/plain; charset=us-ascii Content-transfer-encoding: 7bit Thread-index: Ac5oOQgLbvhlD50JSg2Ru2bWy7927w== Content-language: ko DLP-Filter: Pass Sender: linux-pci-owner@vger.kernel.org Precedence: bulk

On Friday, June 14, 2013 9:54 PM, Arnd Bergmann wrote: > On Friday 14 June 2013 17:18:46 Jingoo Han wrote: > > On Thursday, June 13, 2013 11:14 PM, Arnd Bergmann wrote: > > > On Thursday 13 June 2013 22:22:31 Jingoo Han wrote: > > > > > +struct pcie_port { > > > > + struct device *dev; > > > > + u8 controller; > > > > + u8 root_bus_nr; > > > > + void __iomem *dbi_base; > > > > + void __iomem *elbi_base; > > > > + void __iomem *phy_base; > > > > + void __iomem *purple_base; > > > > + phys_addr_t cfg0_base; > > > > + void __iomem *va_cfg0_base; > > > > + phys_addr_t cfg1_base; > > > > + void __iomem *va_cfg1_base; > > > > + phys_addr_t io_base; > > > > + phys_addr_t mem_base; > > > > + spinlock_t conf_lock; > > > > + struct resource cfg; > > > > + struct resource io; > > > > + struct resource mem; > > > > + struct pcie_port_info config; > > > > + struct clk *clk; > > > > + struct clk *bus_clk; > > > > + int irq; > > > > + int reset_gpio; > > > > +}; > > > > > > You mentioned that you'd use u64 for the resources here but did not. > > > > Do you mean the following? > > > > + u64 cfg0_base; > > + u64 cfg1_base; > > + u64 io_base; > > + u64 mem_base; > > Yes, anything you need to program into a 64 bit hardware register. OK, > > > > > +static void exynos_pcie_prog_viewport_cfg1(struct pcie_port *pp, u32 busdev) > > > > +{ > > > > + u32 val; > > > > + void __iomem *dbi_base = pp->dbi_base; > > > > + > > > > + /* Program viewport 1 : OUTBOUND : CFG1 */ > > > > + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1; > > > > + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); > > > > + writel_rc(pp, PCIE_ATU_TYPE_CFG1, dbi_base + PCIE_ATU_CR1); > > > > + val = PCIE_ATU_ENABLE; > > > > + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); > > > > + writel_rc(pp, (u64)pp->cfg1_base, dbi_base + PCIE_ATU_LOWER_BASE); > > > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); > > > > + writel_rc(pp, (u64)pp->cfg1_base + pp->config.cfg1_size - 1, > > > > + dbi_base + PCIE_ATU_LIMIT); > > > > + writel_rc(pp, busdev, dbi_base + PCIE_ATU_LOWER_TARGET); > > > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); > > > > +} > > > > > > And you still don't set up the UPPER halves, which was really the point > > > of my comment. Same thing for all the other ones. > > > > Do you mean the following? > > > > + writel_rc(pp, pp->cfg1_base, dbi_base + PCIE_ATU_LOWER_BASE); > > + writel_rc(pp, (pp->cfg1_base >> 32), dbi_base + PCIE_ATU_UPPER_BASE); > > Right. Note that you could achieve the same using phys_addr_t instead of > u64, but it's more complicated to get that to work for both 32 and 64 bit > phys_addr_t types, since you cannot shift a 32 bit value by 32 bits in C. OK, > > > > > +static void exynos_pcie_prog_viewport_mem_inbound(struct pcie_port *pp) > > > > +{ > > > > + u32 val; > > > > + void __iomem *dbi_base = pp->dbi_base; > > > > + > > > > + /* Program viewport 0 : INBOUND : MEM */ > > > > + val = PCIE_ATU_REGION_INBOUND | PCIE_ATU_REGION_INDEX0; > > > > + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); > > > > + writel_rc(pp, PCIE_ATU_TYPE_MEM, dbi_base + PCIE_ATU_CR1); > > > > + val = PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE; > > > > + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); > > > > + writel_rc(pp, (u64)pp->config.mem_bus_addr, > > > > + dbi_base + PCIE_ATU_LOWER_BASE); > > > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); > > > > + writel_rc(pp, (u64)pp->config.mem_bus_addr + pp->config.mem_size - 1, > > > > + dbi_base + PCIE_ATU_LIMIT); > > > > + writel_rc(pp, (u64)pp->mem_base, dbi_base + PCIE_ATU_LOWER_TARGET); > > > > + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); > > > > +} > > > > > > This makes even less sense than before, it seems like now you only > > > allow DMA between PCI devices but not to main memory. > > > > Sorry, I cannot understand it. > > Could you give me more details? > > Also, pseudo-code will be very helpful. > > Please look up the documentation about inbound viewport and describe > in a code comment what it does. I /assume/ that this is how DMA accesses > from the bus get translated into AXI bus transactions. If so, you have > to let the window translate addresses from RAM. If it's something else, > then you should document what it is and how it needs to be set up. One of our hardware engineer confirmed it. He said that these inbound functions are unnecessary. Also, I checked that PCIe works properly without these functions. So, I will remove these inbound functions. > > > > > +static int exynos_pcie_setup(int nr, struct pci_sys_data *sys) > > > > +{ > > > > + struct pcie_port *pp; > > > > + > > > > + pp = sys_to_pcie(sys); > > > > + > > > > + if (!pp) > > > > + return 0; > > > > + > > > > + pci_add_resource(&sys->resources, &pp->io); > > > > + pci_add_resource(&sys->resources, &pp->mem); > > > > > > Now you are missing the offsets. You have to at least pass an offset for one > > > of the I/O spaces, since they are using the same bus address. The offset must > > > match the value you pass to pci_ioremap_io. > > > > > > For the memory space, you should pass the difference between the physical > > > base address and the bus address. That address happens to be zero with > > > you DT setup, but I would advise to also try out some other values in DT, > > > just to ensure it still works. > > > > Um, I cannot understand it, too. > > Could you give me Psuedo-code? > > Or, let me know which pcie driver can be the good reference. > > I think most hardware is not as flexible as yours, so they can just hardcode > a lot of this. > > What you need here is > > static unsigned long global_io_offset = 0; > if (global_io_offset < SZ_1M && pp->config.io_size > 0) { > sys->io_offset = global_io_offset - pp->config.io_bus_addr; /* normally 0 */ > pci_ioremap_io(sys->io_offset, pp->io.start); > global_io_offset += SZ_64K; > } > sys->mem_offset = pp->mem.start - pp->config.mem_bus_addr; /* normally 0 */ > > sys->io_offset normally increases by 64K for each bus but should always > be between 0 and 1MB, it is the index into the registers mapped at > (void __iomem*)PCI_IO_VIRT_BASE. > > It is best practice to map 64KB of I/O space at bus address 0 for each > domain into PCI_IO_VIRT_BASE, and set up a 1:1 translation between > memory space bus addresses and CPU physical addresses, as you do > in your 'ranges' property. > > However, you should be able to use any other bus addresses with the code > above, except for broken device drivers. Then, do you mean the following? static unsigned long global_io_offset = 0; static int exynos_pcie_setup(int nr, struct pci_sys_data *sys) { struct pcie_port *pp; pp = sys_to_pcie(sys); if (!pp) return 0; if (global_io_offset < SZ_1M && pp->config.io_size > 0) { sys->io_offset = global_io_offset - pp->config.io_bus_addr; /* normally 0 */ pci_ioremap_io(sys->io_offset, pp->io.start); global_io_offset += SZ_64K; } sys->mem_offset = pp->mem.start - pp->config.mem_bus_addr; /* normally 0 */ pci_add_resource_offset(&sys->resources, &pp->io, sys->io_offset); pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset); return 1; } In this case, boot message is as below: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x40001000-0x40010fff] pci_bus 0000:00: root bus resource [mem 0x40011000-0x5fffffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci 0000:00:00.0: [144d:a549] type 01 class 0x060400 [.....] PCI host bridge to bus 0001:00 pci_bus 0001:00: root bus resource [io 0x60001000-0x60010fff] (bus address [0x5fff1000-0x6000 0fff]) pci_bus 0001:00: root bus resource [mem 0x60011000-0x7fffffff] pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff] pci 0001:00:00.0: [144d:a549] type 01 class 0x060400 > > > > > +static int __exit exynos_pcie_remove(struct platform_device *pdev) > > > > +{ > > > > + struct pcie_port *pp = platform_get_drvdata(pdev); > > > > + > > > > + clk_disable_unprepare(pp->bus_clk); > > > > + clk_disable_unprepare(pp->clk); > > > > + > > > > + return 0; > > > > +} > > > > > > You also don't remove the PCI devices here, as mentioned in an earlier > > > review. > > > > I reviewed Marvell PCIe driver and Tegra PCIe driver; however, > > I cannot know what you mean. > > > > Could let me know which additional functions are needed? > > The mvebu driver does not allow module unload. I haven't looked at the > tegra driver. If you allow unloading the driver and provide a 'remove' > callback, that callback needs to clean up the entire bus and remove > all child devices that were added as well as undo everything the > probe function did. I think it would be great if you can do that, although > it might not be easy. The simplest solution would be to not support > unloading though. As the mvebu driver uses platform_driver_probe(), the Exynos driver uses platform_driver_probe(). Thus, I will not provide a 'remove' callback. Thank you. Best regards, Jingoo Han > > Arnd -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html

diff --git a/Documentation/devicetree/bindings/pci/exynos-pcie.txt b/Documentation/devicetree/bindings/pci/exynos-pcie.txt new file mode 100644 index 0000000..638e68c --- /dev/null +++ b/Documentation/devicetree/bindings/pci/exynos-pcie.txt @@ -0,0 +1,71 @@ +* Samsung Exynos PCIe interface + +Required properties: +-compatible: should be "samsung,exynos5440-pcie" +-reg: base addresses and lengths of the pcie conteroller, + the phy controller, additional register for the phy controller. +- interrupts: interrupt values for level interrupt, + pulse interrupt, special interrupt. +- clocks: from common clock binding: handle to pci clock. +- clock-names: from common clock binding: Shall be "pcie", "pcie_bus". +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- reset-gpio: gpio pin number of power good signal + +Example: + +SoC specific DT Entry: + + pcie0@290000 { + compatible = "samsung,exynos5440-pcie"; + reg = <0x290000 0x1000 + 0x270000 0x1000 + 0x271000 0x40>; + interrupts = <0 20 0>, <0 21 0>, <0 22 0>; + clocks = <&clock 28>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */ + 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0x0 0 &gic 53>; + }; + + pcie1@2a0000 { + compatible = "samsung,exynos5440-pcie"; + reg = <0x2a0000 0x1000 + 0x272000 0x1000 + 0x271040 0x40>; + interrupts = <0 23 0>, <0 24 0>, <0 25 0>; + clocks = <&clock 29>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */ + 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0x0 0 &gic 56>; + }; + +Board specific DT Entry: + + pcie0@290000 { + reset-gpio = <&pin_ctrl 5 0>; + }; + + pcie1@2a0000 { + reset-gpio = <&pin_ctrl 22 0>; + }; diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig index 1f1d67f..fec0f1f 100644 --- a/drivers/pci/host/Kconfig +++ b/drivers/pci/host/Kconfig @@ -5,4 +5,9 @@ config PCI_MVEBU bool "Marvell EBU PCIe controller" depends on ARCH_MVEBU || ARCH_KIRKWOOD +config PCI_EXYNOS + bool "Samsung Exynos PCIe controller" + depends on SOC_EXYNOS5440 + select PCIEPORTBUS + endmenu diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile index 5ea2d8b..31d77ad 100644 --- a/drivers/pci/host/Makefile +++ b/drivers/pci/host/Makefile @@ -1 +1,2 @@ obj-$(CONFIG_PCI_MVEBU) += pci-mvebu.o +obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o diff --git a/drivers/pci/host/pci-exynos.c b/drivers/pci/host/pci-exynos.c new file mode 100644 index 0000000..abfa3dc --- /dev/null +++ b/drivers/pci/host/pci-exynos.c @@ -0,0 +1,1078 @@ +/* + * PCIe host controller driver for Samsung EXYNOS SoCs + * + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Author: Jingoo Han <jg1.han@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_gpio.h> +#include <linux/of_pci.h> +#include <linux/pci.h> +#include <linux/pci_regs.h> +#include <linux/platform_device.h> +#include <linux/resource.h> +#include <linux/signal.h> +#include <linux/slab.h> +#include <linux/types.h> + +struct pcie_port_info { + u32 cfg0_size; + u32 cfg1_size; + u32 io_size; + u32 mem_size; + phys_addr_t io_bus_addr; + phys_addr_t mem_bus_addr; +}; + +struct pcie_port { + struct device *dev; + u8 controller; + u8 root_bus_nr; + void __iomem *dbi_base; + void __iomem *elbi_base; + void __iomem *phy_base; + void __iomem *purple_base; + phys_addr_t cfg0_base; + void __iomem *va_cfg0_base; + phys_addr_t cfg1_base; + void __iomem *va_cfg1_base; + phys_addr_t io_base; + phys_addr_t mem_base; + spinlock_t conf_lock; + struct resource cfg; + struct resource io; + struct resource mem; + struct pcie_port_info config; + struct clk *clk; + struct clk *bus_clk; + int irq; + int reset_gpio; +}; + +/* synopsis specific PCIE configuration registers*/ +#define PCIE_PORT_LINK_CONTROL 0x710 +#define PORT_LINK_MODE_MASK (0x3f << 16) +#define PORT_LINK_MODE_4_LANES (0x7 << 16) + +#define PCIE_LINK_WIDTH_SPEED_CONTROL 0x80C +#define PORT_LOGIC_SPEED_CHANGE (0x1 << 17) +#define PORT_LOGIC_LINK_WIDTH_MASK (0x1ff << 8) +#define PORT_LOGIC_LINK_WIDTH_4_LANES (0x7 << 8) + +#define PCIE_MSI_ADDR_LO 0x820 +#define PCIE_MSI_ADDR_HI 0x824 +#define PCIE_MSI_INTR0_ENABLE 0x828 +#define PCIE_MSI_INTR0_MASK 0x82C +#define PCIE_MSI_INTR0_STATUS 0x830 + +#define PCIE_ATU_VIEWPORT 0x900 +#define PCIE_ATU_REGION_INBOUND (0x1 << 31) +#define PCIE_ATU_REGION_OUTBOUND (0x0 << 31) +#define PCIE_ATU_REGION_INDEX1 (0x1 << 0) +#define PCIE_ATU_REGION_INDEX0 (0x0 << 0) +#define PCIE_ATU_CR1 0x904 +#define PCIE_ATU_TYPE_MEM (0x0 << 0) +#define PCIE_ATU_TYPE_IO (0x2 << 0) +#define PCIE_ATU_TYPE_CFG0 (0x4 << 0) +#define PCIE_ATU_TYPE_CFG1 (0x5 << 0) +#define PCIE_ATU_CR2 0x908 +#define PCIE_ATU_ENABLE (0x1 << 31) +#define PCIE_ATU_BAR_MODE_ENABLE (0x1 << 30) +#define PCIE_ATU_LOWER_BASE 0x90C +#define PCIE_ATU_UPPER_BASE 0x910 +#define PCIE_ATU_LIMIT 0x914 +#define PCIE_ATU_LOWER_TARGET 0x918 +#define PCIE_ATU_BUS(x) (((x) & 0xff) << 24) +#define PCIE_ATU_DEV(x) (((x) & 0x1f) << 19) +#define PCIE_ATU_FUNC(x) (((x) & 0x7) << 16) +#define PCIE_ATU_UPPER_TARGET 0x91C + +/* PCIe ELBI registers */ +#define PCIE_IRQ_PULSE 0x000 +#define IRQ_INTA_ASSERT (0x1 << 0) +#define IRQ_INTB_ASSERT (0x1 << 2) +#define IRQ_INTC_ASSERT (0x1 << 4) +#define IRQ_INTD_ASSERT (0x1 << 6) +#define PCIE_IRQ_LEVEL 0x004 +#define PCIE_IRQ_SPECIAL 0x008 +#define PCIE_IRQ_EN_PULSE 0x00c +#define PCIE_IRQ_EN_LEVEL 0x010 +#define PCIE_IRQ_EN_SPECIAL 0x014 +#define PCIE_PWR_RESET 0x018 +#define PCIE_CORE_RESET 0x01c +#define PCIE_CORE_RESET_ENABLE (0x1 << 0) +#define PCIE_STICKY_RESET 0x020 +#define PCIE_NONSTICKY_RESET 0x024 +#define PCIE_APP_INIT_RESET 0x028 +#define PCIE_APP_LTSSM_ENABLE 0x02c +#define PCIE_ELBI_RDLH_LINKUP 0x064 +#define PCIE_ELBI_LTSSM_ENABLE 0x1 +#define PCIE_ELBI_SLV_AWMISC 0x11c +#define PCIE_ELBI_SLV_ARMISC 0x120 +#define PCIE_ELBI_SLV_DBI_ENABLE (0x1 << 21) + +/* PCIe Purple registers */ +#define PCIE_PHY_GLOBAL_RESET 0x000 +#define PCIE_PHY_COMMON_RESET 0x004 +#define PCIE_PHY_CMN_REG 0x008 +#define PCIE_PHY_MAC_RESET 0x00c +#define PCIE_PHY_PLL_LOCKED 0x010 +#define PCIE_PHY_TRSVREG_RESET 0x020 +#define PCIE_PHY_TRSV_RESET 0x024 + +/* PCIe PHY registers */ +#define PCIE_PHY_IMPEDANCE 0x004 +#define PCIE_PHY_PLL_DIV_0 0x008 +#define PCIE_PHY_PLL_BIAS 0x00c +#define PCIE_PHY_DCC_FEEDBACK 0x014 +#define PCIE_PHY_PLL_DIV_1 0x05c +#define PCIE_PHY_TRSV0_EMP_LVL 0x084 +#define PCIE_PHY_TRSV0_DRV_LVL 0x088 +#define PCIE_PHY_TRSV0_RXCDR 0x0ac +#define PCIE_PHY_TRSV0_LVCC 0x0dc +#define PCIE_PHY_TRSV1_EMP_LVL 0x144 +#define PCIE_PHY_TRSV1_RXCDR 0x16c +#define PCIE_PHY_TRSV1_LVCC 0x19c +#define PCIE_PHY_TRSV2_EMP_LVL 0x204 +#define PCIE_PHY_TRSV2_RXCDR 0x22c +#define PCIE_PHY_TRSV2_LVCC 0x25c +#define PCIE_PHY_TRSV3_EMP_LVL 0x2c4 +#define PCIE_PHY_TRSV3_RXCDR 0x2ec +#define PCIE_PHY_TRSV3_LVCC 0x31c + +static struct hw_pci exynos_pci; + +static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys) +{ + return sys->private_data; +} + +static inline int cfg_read(void *addr, int where, int size, u32 *val) +{ + *val = readl(addr); + + if (size == 1) + *val = (*val >> (8 * (where & 3))) & 0xff; + else if (size == 2) + *val = (*val >> (8 * (where & 3))) & 0xffff; + else if (size != 4) + return PCIBIOS_BAD_REGISTER_NUMBER; + + return PCIBIOS_SUCCESSFUL; +} + +static inline int cfg_write(void *addr, int where, int size, u32 val) +{ + if (size == 4) + writel(val, addr); + else if (size == 2) + writew(val, addr + (where & 2)); + else if (size == 1) + writeb(val, addr + (where & 3)); + else + return PCIBIOS_BAD_REGISTER_NUMBER; + + return PCIBIOS_SUCCESSFUL; +} + +static void exynos_pcie_sideband_dbi_w_mode(struct pcie_port *pp, bool on) +{ + u32 val; + + if (on) { + val = readl(pp->elbi_base + PCIE_ELBI_SLV_AWMISC); + val |= PCIE_ELBI_SLV_DBI_ENABLE; + writel(val, pp->elbi_base + PCIE_ELBI_SLV_AWMISC); + } else { + val = readl(pp->elbi_base + PCIE_ELBI_SLV_AWMISC); + val &= ~PCIE_ELBI_SLV_DBI_ENABLE; + writel(val, pp->elbi_base + PCIE_ELBI_SLV_AWMISC); + } +} + +static void exynos_pcie_sideband_dbi_r_mode(struct pcie_port *pp, bool on) +{ + u32 val; + + if (on) { + val = readl(pp->elbi_base + PCIE_ELBI_SLV_ARMISC); + val |= PCIE_ELBI_SLV_DBI_ENABLE; + writel(val, pp->elbi_base + PCIE_ELBI_SLV_ARMISC); + } else { + val = readl(pp->elbi_base + PCIE_ELBI_SLV_ARMISC); + val &= ~PCIE_ELBI_SLV_DBI_ENABLE; + writel(val, pp->elbi_base + PCIE_ELBI_SLV_ARMISC); + } +} + +static inline void readl_rc(struct pcie_port *pp, void *dbi_base, u32 *val) +{ + exynos_pcie_sideband_dbi_r_mode(pp, true); + *val = readl(dbi_base); + exynos_pcie_sideband_dbi_r_mode(pp, false); + return; +} + +static inline void writel_rc(struct pcie_port *pp, u32 val, void *dbi_base) +{ + exynos_pcie_sideband_dbi_w_mode(pp, true); + writel(val, dbi_base); + exynos_pcie_sideband_dbi_w_mode(pp, false); + return; +} + +static int exynos_pcie_rd_own_conf(struct pcie_port *pp, int where, int size, + u32 *val) +{ + int ret; + + exynos_pcie_sideband_dbi_r_mode(pp, true); + ret = cfg_read(pp->dbi_base + (where & ~0x3), where, size, val); + exynos_pcie_sideband_dbi_r_mode(pp, false); + return ret; +} + +static int exynos_pcie_wr_own_conf(struct pcie_port *pp, int where, int size, + u32 val) +{ + int ret; + + exynos_pcie_sideband_dbi_w_mode(pp, true); + ret = cfg_write(pp->dbi_base + (where & ~0x3), where, size, val); + exynos_pcie_sideband_dbi_w_mode(pp, false); + return ret; +} + +static void exynos_pcie_prog_viewport_cfg0(struct pcie_port *pp, u32 busdev) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 0 : OUTBOUND : CFG0 */ + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, (u64)pp->cfg0_base, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u64)pp->cfg0_base + pp->config.cfg0_size - 1, + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, busdev, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); + writel_rc(pp, PCIE_ATU_TYPE_CFG0, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); +} + +static void exynos_pcie_prog_viewport_cfg1(struct pcie_port *pp, u32 busdev) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 1 : OUTBOUND : CFG1 */ + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_CFG1, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, (u64)pp->cfg1_base, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u64)pp->cfg1_base + pp->config.cfg1_size - 1, + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, busdev, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static void exynos_pcie_prog_viewport_mem_outbound(struct pcie_port *pp) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 0 : OUTBOUND : MEM */ + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_MEM, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, (u64)pp->mem_base, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u64)pp->mem_base + pp->config.mem_size - 1, + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, (u64)pp->config.mem_bus_addr, + dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static void exynos_pcie_prog_viewport_io_outbound(struct pcie_port *pp) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 1 : OUTBOUND : IO */ + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_IO, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, (u64)pp->io_base, dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u64)pp->io_base + pp->config.io_size - 1, + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, (u64)pp->config.io_bus_addr, + dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static void exynos_pcie_prog_viewport_mem_inbound(struct pcie_port *pp) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 0 : INBOUND : MEM */ + val = PCIE_ATU_REGION_INBOUND | PCIE_ATU_REGION_INDEX0; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_MEM, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, (u64)pp->config.mem_bus_addr, + dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u64)pp->config.mem_bus_addr + pp->config.mem_size - 1, + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, (u64)pp->mem_base, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static void exynos_pcie_prog_viewport_io_inbound(struct pcie_port *pp) +{ + u32 val; + void __iomem *dbi_base = pp->dbi_base; + + /* Program viewport 1 : INBOUND : IO */ + val = PCIE_ATU_REGION_INBOUND | PCIE_ATU_REGION_INDEX1; + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT); + writel_rc(pp, PCIE_ATU_TYPE_IO, dbi_base + PCIE_ATU_CR1); + val = PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE; + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2); + writel_rc(pp, (u64)pp->config.io_bus_addr, + dbi_base + PCIE_ATU_LOWER_BASE); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE); + writel_rc(pp, (u64)pp->config.io_bus_addr + pp->config.io_size - 1, + dbi_base + PCIE_ATU_LIMIT); + writel_rc(pp, (u64)pp->io_base, dbi_base + PCIE_ATU_LOWER_TARGET); + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET); +} + +static int exynos_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus, + u32 devfn, int where, int size, u32 *val) +{ + int ret = PCIBIOS_SUCCESSFUL; + u32 address, busdev; + + busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) | + PCIE_ATU_FUNC(PCI_FUNC(devfn)); + address = where & ~0x3; + + if (bus->parent->number == pp->root_bus_nr) { + exynos_pcie_prog_viewport_cfg0(pp, busdev); + ret = cfg_read(pp->va_cfg0_base + address, where, size, val); + exynos_pcie_prog_viewport_mem_outbound(pp); + } else { + exynos_pcie_prog_viewport_cfg1(pp, busdev); + ret = cfg_read(pp->va_cfg1_base + address, where, size, val); + exynos_pcie_prog_viewport_io_outbound(pp); + } + + return ret; +} + +static int exynos_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus, + u32 devfn, int where, int size, u32 val) +{ + int ret = PCIBIOS_SUCCESSFUL; + u32 address, busdev; + + busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) | + PCIE_ATU_FUNC(PCI_FUNC(devfn)); + address = where & ~0x3; + + if (bus->parent->number == pp->root_bus_nr) { + exynos_pcie_prog_viewport_cfg0(pp, busdev); + ret = cfg_write(pp->va_cfg0_base + address, where, size, val); + exynos_pcie_prog_viewport_mem_outbound(pp); + } else { + exynos_pcie_prog_viewport_cfg1(pp, busdev); + ret = cfg_write(pp->va_cfg1_base + address, where, size, val); + exynos_pcie_prog_viewport_io_outbound(pp); + } + + return ret; +} + +static int exynos_pcie_setup(int nr, struct pci_sys_data *sys) +{ + struct pcie_port *pp; + + pp = sys_to_pcie(sys); + + if (!pp) + return 0; + + pci_add_resource(&sys->resources, &pp->io); + pci_add_resource(&sys->resources, &pp->mem); + + return 1; +} + +static int exynos_pcie_link_up(struct pcie_port *pp) +{ + u32 val = readl(pp->elbi_base + PCIE_ELBI_RDLH_LINKUP); + if (val == PCIE_ELBI_LTSSM_ENABLE) + return 1; + + return 0; +} + +static int exynos_pcie_valid_config(struct pcie_port *pp, + struct pci_bus *bus, int dev) +{ + /* If there is no link, then there is no device */ + if (bus->number != pp->root_bus_nr) { + if (!exynos_pcie_link_up(pp)) + return 0; + } + + /* access only one slot on each root port */ + if (bus->number == pp->root_bus_nr && dev > 0) + return 0; + + /* + * do not read more than one device on the bus directly attached + * to RC's (Virtual Bridge's) DS side. + */ + if (bus->primary == pp->root_bus_nr && dev > 0) + return 0; + + return 1; +} + +static int exynos_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, + int size, u32 *val) +{ + struct pcie_port *pp = sys_to_pcie(bus->sysdata); + unsigned long flags; + int ret; + + if (!pp) { + BUG(); + return -EINVAL; + } + + if (exynos_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) { + *val = 0xffffffff; + return PCIBIOS_DEVICE_NOT_FOUND; + } + + spin_lock_irqsave(&pp->conf_lock, flags); + if (bus->number != pp->root_bus_nr) + ret = exynos_pcie_rd_other_conf(pp, bus, devfn, + where, size, val); + else + ret = exynos_pcie_rd_own_conf(pp, where, size, val); + spin_unlock_irqrestore(&pp->conf_lock, flags); + + return ret; +} + +static int exynos_pcie_wr_conf(struct pci_bus *bus, u32 devfn, + int where, int size, u32 val) +{ + struct pcie_port *pp = sys_to_pcie(bus->sysdata); + unsigned long flags; + int ret; + + if (!pp) { + BUG(); + return -EINVAL; + } + + if (exynos_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) + return PCIBIOS_DEVICE_NOT_FOUND; + + spin_lock_irqsave(&pp->conf_lock, flags); + if (bus->number != pp->root_bus_nr) + ret = exynos_pcie_wr_other_conf(pp, bus, devfn, + where, size, val); + else + ret = exynos_pcie_wr_own_conf(pp, where, size, val); + spin_unlock_irqrestore(&pp->conf_lock, flags); + + return ret; +} + +static struct pci_ops exynos_pcie_ops = { + .read = exynos_pcie_rd_conf, + .write = exynos_pcie_wr_conf, +}; + +static struct pci_bus *exynos_pcie_scan_bus(int nr, + struct pci_sys_data *sys) +{ + struct pci_bus *bus; + struct pcie_port *pp = sys_to_pcie(sys); + + if (pp) { + pp->root_bus_nr = sys->busnr; + bus = pci_scan_root_bus(NULL, sys->busnr, &exynos_pcie_ops, + sys, &sys->resources); + return bus; + } else { + bus = NULL; + BUG(); + } + + return bus; +} + +static int exynos_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) +{ + struct pcie_port *pp = sys_to_pcie(dev->bus->sysdata); + + return pp->irq; +} + +static struct hw_pci exynos_pci = { + .setup = exynos_pcie_setup, + .scan = exynos_pcie_scan_bus, + .map_irq = exynos_pcie_map_irq, +}; + +static void exynos_pcie_setup_rc(struct pcie_port *pp) +{ + struct pcie_port_info *config = &pp->config; + void __iomem *dbi_base = pp->dbi_base; + u32 val; + u32 membase; + u32 memlimit; + + /* set the number of lines as 4 */ + readl_rc(pp, dbi_base + PCIE_PORT_LINK_CONTROL, &val); + val &= ~PORT_LINK_MODE_MASK; + val |= PORT_LINK_MODE_4_LANES; + writel_rc(pp, val, dbi_base + PCIE_PORT_LINK_CONTROL); + + /* set link width speed control register */ + readl_rc(pp, dbi_base + PCIE_LINK_WIDTH_SPEED_CONTROL, &val); + val &= ~PORT_LOGIC_LINK_WIDTH_MASK; + val |= PORT_LOGIC_LINK_WIDTH_4_LANES; + writel_rc(pp, val, dbi_base + PCIE_LINK_WIDTH_SPEED_CONTROL); + + /* setup RC BARs */ + writel_rc(pp, 0x00000004, dbi_base + PCI_BASE_ADDRESS_0); + writel_rc(pp, 0x00000004, dbi_base + PCI_BASE_ADDRESS_1); + + /* setup interrupt pins */ + readl_rc(pp, dbi_base + PCI_INTERRUPT_LINE, &val); + val &= 0xffff00ff; + val |= 0x00000100; + writel_rc(pp, val, dbi_base + PCI_INTERRUPT_LINE); + + /* setup bus numbers */ + readl_rc(pp, dbi_base + PCI_PRIMARY_BUS, &val); + val &= 0xff000000; + val |= 0x00010100; + writel_rc(pp, val, dbi_base + PCI_PRIMARY_BUS); + + /* setup memory base, memory limit */ + membase = ((u32)pp->mem_base & 0xfff00000) >> 16; + memlimit = (config->mem_size + (u32)pp->mem_base) & 0xfff00000; + val = memlimit | membase; + writel_rc(pp, val, dbi_base + PCI_MEMORY_BASE); + + /* setup command register */ + readl_rc(pp, dbi_base + PCI_COMMAND, &val); + val &= 0xffff0000; + val |= PCI_COMMAND_IO | PCI_COMMAND_MEMORY | + PCI_COMMAND_MASTER | PCI_COMMAND_SERR; + writel_rc(pp, val, dbi_base + PCI_COMMAND); +} + +static void exynos_pcie_assert_core_reset(struct pcie_port *pp) +{ + u32 val; + void __iomem *elbi_base = pp->elbi_base; + + val = readl(elbi_base + PCIE_CORE_RESET); + val &= ~PCIE_CORE_RESET_ENABLE; + writel(val, elbi_base + PCIE_CORE_RESET); + writel(0, elbi_base + PCIE_PWR_RESET); + writel(0, elbi_base + PCIE_STICKY_RESET); + writel(0, elbi_base + PCIE_NONSTICKY_RESET); +} + +static void exynos_pcie_deassert_core_reset(struct pcie_port *pp) +{ + u32 val; + void __iomem *elbi_base = pp->elbi_base; + void __iomem *purple_base = pp->purple_base; + + val = readl(elbi_base + PCIE_CORE_RESET); + val |= PCIE_CORE_RESET_ENABLE; + writel(val, elbi_base + PCIE_CORE_RESET); + writel(1, elbi_base + PCIE_STICKY_RESET); + writel(1, elbi_base + PCIE_NONSTICKY_RESET); + writel(1, elbi_base + PCIE_APP_INIT_RESET); + writel(0, elbi_base + PCIE_APP_INIT_RESET); + writel(1, purple_base + PCIE_PHY_MAC_RESET); +} + +static void exynos_pcie_assert_phy_reset(struct pcie_port *pp) +{ + void __iomem *purple_base = pp->purple_base; + + writel(0, purple_base + PCIE_PHY_MAC_RESET); + writel(1, purple_base + PCIE_PHY_GLOBAL_RESET); +} + +static void exynos_pcie_deassert_phy_reset(struct pcie_port *pp) +{ + void __iomem *elbi_base = pp->elbi_base; + void __iomem *purple_base = pp->purple_base; + + writel(0, purple_base + PCIE_PHY_GLOBAL_RESET); + writel(1, elbi_base + PCIE_PWR_RESET); + writel(0, purple_base + PCIE_PHY_COMMON_RESET); + writel(0, purple_base + PCIE_PHY_CMN_REG); + writel(0, purple_base + PCIE_PHY_TRSVREG_RESET); + writel(0, purple_base + PCIE_PHY_TRSV_RESET); +} + +static void exynos_pcie_init_phy(struct pcie_port *pp) +{ + void __iomem *phy_base = pp->phy_base; + + /* DCC feedback control off */ + writel(0x29, phy_base + PCIE_PHY_DCC_FEEDBACK); + + /* set TX/RX impedance */ + writel(0xd5, phy_base + PCIE_PHY_IMPEDANCE); + + /* set 50Mhz PHY clock */ + writel(0x14, phy_base + PCIE_PHY_PLL_DIV_0); + writel(0x12, phy_base + PCIE_PHY_PLL_DIV_1); + + /* set TX Differential output for lane 0 */ + writel(0x7f, phy_base + PCIE_PHY_TRSV0_DRV_LVL); + + /* set TX Pre-emphasis Level Control for lane 0 to minimum */ + writel(0x0, phy_base + PCIE_PHY_TRSV0_EMP_LVL); + + /* set RX clock and data recovery bandwidth */ + writel(0xe7, phy_base + PCIE_PHY_PLL_BIAS); + writel(0x82, phy_base + PCIE_PHY_TRSV0_RXCDR); + writel(0x82, phy_base + PCIE_PHY_TRSV1_RXCDR); + writel(0x82, phy_base + PCIE_PHY_TRSV2_RXCDR); + writel(0x82, phy_base + PCIE_PHY_TRSV3_RXCDR); + + /* change TX Pre-emphasis Level Control for lanes */ + writel(0x39, phy_base + PCIE_PHY_TRSV0_EMP_LVL); + writel(0x39, phy_base + PCIE_PHY_TRSV1_EMP_LVL); + writel(0x39, phy_base + PCIE_PHY_TRSV2_EMP_LVL); + writel(0x39, phy_base + PCIE_PHY_TRSV3_EMP_LVL); + + /* set LVCC */ + writel(0x20, phy_base + PCIE_PHY_TRSV0_LVCC); + writel(0xa0, phy_base + PCIE_PHY_TRSV1_LVCC); + writel(0xa0, phy_base + PCIE_PHY_TRSV2_LVCC); + writel(0xa0, phy_base + PCIE_PHY_TRSV3_LVCC); +} + +static void exynos_pcie_assert_reset(struct pcie_port *pp) +{ + if (pp->reset_gpio >= 0) + devm_gpio_request_one(pp->dev, pp->reset_gpio, + GPIOF_OUT_INIT_HIGH, "RESET"); + return; +} + +static int exynos_pcie_establish_link(struct pcie_port *pp) +{ + u32 val; + int count = 0; + void __iomem *elbi_base = pp->elbi_base; + void __iomem *purple_base = pp->purple_base; + void __iomem *phy_base = pp->phy_base; + + if (exynos_pcie_link_up(pp)) { + dev_err(pp->dev, "Link already up\n"); + return 0; + } + + /* assert reset signals */ + exynos_pcie_assert_core_reset(pp); + exynos_pcie_assert_phy_reset(pp); + + /* de-assert phy reset */ + exynos_pcie_deassert_phy_reset(pp); + + /* initialize phy */ + exynos_pcie_init_phy(pp); + + /* pulse for common reset */ + writel(1, purple_base + PCIE_PHY_COMMON_RESET); + udelay(500); + writel(0, purple_base + PCIE_PHY_COMMON_RESET); + + /* de-assert core reset */ + exynos_pcie_deassert_core_reset(pp); + + /* setup root complex */ + exynos_pcie_setup_rc(pp); + + /* assert reset signal */ + exynos_pcie_assert_reset(pp); + + /* assert LTSSM enable */ + writel(PCIE_ELBI_LTSSM_ENABLE, elbi_base + PCIE_APP_LTSSM_ENABLE); + + /* check if the link is up or not */ + while (!exynos_pcie_link_up(pp)) { + mdelay(100); + count++; + if (count == 10) { + while (readl(phy_base + PCIE_PHY_PLL_LOCKED) == 0) { + val = readl(purple_base + PCIE_PHY_PLL_LOCKED); + dev_info(pp->dev, "PLL Locked: 0x%x\n", val); + } + dev_err(pp->dev, "PCIe Link Fail\n"); + return -EINVAL; + } + } + + dev_info(pp->dev, "Link up\n"); + + return 0; +} + +static void exynos_pcie_clear_irq_pulse(struct pcie_port *pp) +{ + u32 val; + void __iomem *elbi_base = pp->elbi_base; + + val = readl(elbi_base + PCIE_IRQ_PULSE); + writel(val, elbi_base + PCIE_IRQ_PULSE); + return; +} + +static void exynos_pcie_enable_irq_pulse(struct pcie_port *pp) +{ + u32 val; + void __iomem *elbi_base = pp->elbi_base; + + /* enable INTX interrupt */ + val = IRQ_INTA_ASSERT | IRQ_INTB_ASSERT | + IRQ_INTC_ASSERT | IRQ_INTD_ASSERT, + writel(val, elbi_base + PCIE_IRQ_EN_PULSE); + return; +} + +static irqreturn_t exynos_pcie_irq_handler(int irq, void *arg) +{ + struct pcie_port *pp = arg; + + exynos_pcie_clear_irq_pulse(pp); + return IRQ_HANDLED; +} + +static void exynos_pcie_enable_interrupts(struct pcie_port *pp) +{ + exynos_pcie_enable_irq_pulse(pp); + return; +} + +static void exynos_pcie_host_init(struct pcie_port *pp) +{ + struct pcie_port_info *config = &pp->config; + u32 val; + + /* Keep first 64K for IO */ + pp->cfg0_base = pp->cfg.start; + pp->cfg1_base = pp->cfg.start + config->cfg0_size; + pp->io_base = pp->io.start; + pp->mem_base = pp->mem.start; + + /* enable link */ + exynos_pcie_establish_link(pp); + + /* set view ports for inbound */ + exynos_pcie_prog_viewport_mem_inbound(pp); + exynos_pcie_prog_viewport_io_inbound(pp); + + exynos_pcie_wr_own_conf(pp, PCI_BASE_ADDRESS_0, 4, 0); + + /* program correct class for RC */ + exynos_pcie_wr_own_conf(pp, PCI_CLASS_DEVICE, 2, PCI_CLASS_BRIDGE_PCI); + + exynos_pcie_rd_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, &val); + val |= PORT_LOGIC_SPEED_CHANGE; + exynos_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val); + + exynos_pcie_enable_interrupts(pp); +} + +static int add_pcie_port(struct pcie_port *pp, struct platform_device *pdev) +{ + struct resource *elbi_base; + struct resource *phy_base; + struct resource *purple_base; + int ret; + + elbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!elbi_base) { + dev_err(&pdev->dev, "couldn't get elbi base resource\n"); + return -EINVAL; + } + pp->elbi_base = devm_ioremap_resource(&pdev->dev, elbi_base); + if (IS_ERR(pp->elbi_base)) + return PTR_ERR(pp->elbi_base); + + phy_base = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!phy_base) { + dev_err(&pdev->dev, "couldn't get phy base resource\n"); + return -EINVAL; + } + pp->phy_base = devm_ioremap_resource(&pdev->dev, phy_base); + if (IS_ERR(pp->phy_base)) + return PTR_ERR(pp->phy_base); + + purple_base = platform_get_resource(pdev, IORESOURCE_MEM, 2); + if (!purple_base) { + dev_err(&pdev->dev, "couldn't get purple base resource\n"); + return -EINVAL; + } + pp->purple_base = devm_ioremap_resource(&pdev->dev, purple_base); + if (IS_ERR(pp->purple_base)) + return PTR_ERR(pp->purple_base); + + pp->irq = platform_get_irq(pdev, 1); + if (!pp->irq) { + dev_err(&pdev->dev, "failed to get irq\n"); + return -ENODEV; + } + ret = devm_request_irq(&pdev->dev, pp->irq, exynos_pcie_irq_handler, + IRQF_SHARED, "exynos-pcie", pp); + if (ret) { + dev_err(&pdev->dev, "failed to request irq\n"); + return ret; + } + + pp->dbi_base = devm_ioremap(&pdev->dev, pp->cfg.start, + resource_size(&pp->cfg)); + if (!pp->dbi_base) { + dev_err(&pdev->dev, "error with ioremap\n"); + return -ENOMEM; + } + + pp->root_bus_nr = -1; + + spin_lock_init(&pp->conf_lock); + exynos_pcie_host_init(pp); + pp->va_cfg0_base = devm_ioremap(&pdev->dev, pp->cfg0_base, + pp->config.cfg0_size); + if (!pp->va_cfg0_base) { + dev_err(pp->dev, "error with ioremap in function\n"); + return -ENOMEM; + } + pp->va_cfg1_base = devm_ioremap(&pdev->dev, pp->cfg1_base, + pp->config.cfg1_size); + if (!pp->va_cfg1_base) { + dev_err(pp->dev, "error with ioremap\n"); + return -ENOMEM; + } + + return 0; +} + +static int __init exynos_pcie_probe(struct platform_device *pdev) +{ + struct pcie_port *pp; + struct device_node *np = pdev->dev.of_node; + struct of_pci_range range; + struct of_pci_range_parser parser; + int ret; + + pp = devm_kzalloc(&pdev->dev, sizeof(*pp), GFP_KERNEL); + if (!pp) { + dev_err(&pdev->dev, "no memory for pcie port\n"); + return -ENOMEM; + } + + pp->dev = &pdev->dev; + + if (of_pci_range_parser_init(&parser, np)) { + dev_err(&pdev->dev, "missing ranges property\n"); + return -EINVAL; + } + + /* Get the I/O and memory ranges from DT */ + for_each_of_pci_range(&parser, &range) { + unsigned long restype = range.flags & IORESOURCE_TYPE_BITS; + if (restype == IORESOURCE_IO) { + of_pci_range_to_resource(&range, np, &pp->io); + pp->io.name = "I/O"; + pp->config.io_size = resource_size(&pp->io); + pp->config.io_bus_addr = range.pci_addr; + } + if (restype == IORESOURCE_MEM) { + of_pci_range_to_resource(&range, np, &pp->mem); + pp->mem.name = "MEM"; + pp->config.mem_size = resource_size(&pp->mem); + pp->config.mem_bus_addr = range.pci_addr; + } + if (restype == 0) { + of_pci_range_to_resource(&range, np, &pp->cfg); + pp->config.cfg0_size = resource_size(&pp->cfg)/2; + pp->config.cfg1_size = resource_size(&pp->cfg)/2; + } + } + + pp->reset_gpio = of_get_named_gpio(np, "reset-gpio", 0); + + pp->clk = devm_clk_get(&pdev->dev, "pcie"); + if (IS_ERR(pp->clk)) { + dev_err(&pdev->dev, "Failed to get pcie rc clock\n"); + return PTR_ERR(pp->clk); + } + ret = clk_prepare_enable(pp->clk); + if (ret) + return ret; + + pp->bus_clk = devm_clk_get(&pdev->dev, "pcie_bus"); + if (IS_ERR(pp->bus_clk)) { + dev_err(&pdev->dev, "Failed to get pcie bus clock\n"); + ret = PTR_ERR(pp->bus_clk); + goto fail_clk; + } + ret = clk_prepare_enable(pp->bus_clk); + if (ret) + goto fail_clk; + + ret = add_pcie_port(pp, pdev); + if (ret < 0) + goto fail_bus_clk; + + pp->controller = exynos_pci.nr_controllers; + exynos_pci.nr_controllers = 1; + exynos_pci.private_data = (void **)&pp; + + pci_common_init(&exynos_pci); + pci_assign_unassigned_resources(); +#ifdef CONFIG_PCI_DOMAINS + exynos_pci.domain++; +#endif + + platform_set_drvdata(pdev, pp); + return 0; + +fail_bus_clk: + clk_disable_unprepare(pp->bus_clk); +fail_clk: + clk_disable_unprepare(pp->clk); + return ret; +} + +static int __exit exynos_pcie_remove(struct platform_device *pdev) +{ + struct pcie_port *pp = platform_get_drvdata(pdev); + + clk_disable_unprepare(pp->bus_clk); + clk_disable_unprepare(pp->clk); + + return 0; +} + +static const struct of_device_id exynos_pcie_of_match[] = { + { .compatible = "samsung,exynos5440-pcie", }, + {}, +}; +MODULE_DEVICE_TABLE(of, exynos_pcie_of_match); + +static struct platform_driver exynos_pcie_driver = { + .remove = __exit_p(exynos_pcie_remove), + .driver = { + .name = "exynos-pcie", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(exynos_pcie_of_match), + }, +}; + +static int exynos_pcie_abort(unsigned long addr, unsigned int fsr, + struct pt_regs *regs) +{ + unsigned long pc = instruction_pointer(regs); + unsigned long instr = *(unsigned long *)pc; + + WARN_ONCE(1, "pcie abort\n"); + + /* + * If the instruction being executed was a read, + * make it look like it read all-ones. + */ + if ((instr & 0x0c100000) == 0x04100000) { + int reg = (instr >> 12) & 15; + unsigned long val; + + if (instr & 0x00400000) + val = 255; + else + val = -1; + + regs->uregs[reg] = val; + regs->ARM_pc += 4; + return 0; + } + + if ((instr & 0x0e100090) == 0x00100090) { + int reg = (instr >> 12) & 15; + + regs->uregs[reg] = -1; + regs->ARM_pc += 4; + return 0; + } + + return 1; +} + +static int __init pcie_init(void) +{ + hook_fault_code(16 + 6, exynos_pcie_abort, SIGBUS, 0, + "imprecise external abort"); + + platform_driver_probe(&exynos_pcie_driver, exynos_pcie_probe); + + return 0; +} +subsys_initcall(pcie_init); + +static void __exit pcie_exit(void) +{ + platform_driver_unregister(&exynos_pcie_driver); +} +module_exit(pcie_exit); + +MODULE_AUTHOR("Jingoo Han <jg1.han@samsung.com>"); +MODULE_DESCRIPTION("Samsung PCIe host controller driver"); +MODULE_LICENSE("GPLv2");

[V5,1/3] pci: Add PCIe driver for Samsung Exynos

Commit Message

Comments

Patch