| Message ID | 1371106793-25071-1-git-send-email-horms+renesas@verge.net.au |
|---|---|
| State | New |
| Headers | show |
Hi Simon On Thu, 13 Jun 2013, Simon Horman wrote: > From: Magnus Damm <damm@opensource.se> > > Remove board support for the sh7372 based AP4EVB board > > The sh7372 SoC support code is still kept around since it > is in use by the Mackerel board which is basically a more > recent board where the design is based on AP4EVB. > > Signed-off-by: Magnus Damm <damm@opensource.se> > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> It would be a pity if this patch gets pulled now. We're still discussing with Magnus, I believe. My opinion is, that this board is a good testing platform for V4L2. It is the only board in the mainline, using the CSI2 interface, present on multiple Renesas SoCs, including r8a73a4 (APE6), and (probably, not 100% sure) sh73a0 (AG5), and the IMX074 camera sensor, not present on any other platform. If this board is removed, supporting both CSI2 and IMX074 will become difficult. Besides, AP4EVB is used as an example in my V4L2 clock / async probing patch series: http://www.mail-archive.com/linux-media@vger.kernel.org/msg63174.html If still possible, would be good to delay removing this board until we complete our discussion. Thanks Guennadi > --- > arch/arm/configs/ap4evb_defconfig | 56 - > arch/arm/mach-shmobile/Kconfig | 21 - > arch/arm/mach-shmobile/Makefile | 1 - > arch/arm/mach-shmobile/Makefile.boot | 1 - > arch/arm/mach-shmobile/board-ap4evb.c | 1310 -------------------- > .../arm/mach-shmobile/include/mach/head-ap4evb.txt | 93 -- > arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h | 29 - > arch/arm/mach-shmobile/include/mach/mmc.h | 4 +- > arch/arm/mach-shmobile/include/mach/zboot.h | 6 +- > 9 files changed, 2 insertions(+), 1519 deletions(-) > delete mode 100644 arch/arm/configs/ap4evb_defconfig > delete mode 100644 arch/arm/mach-shmobile/board-ap4evb.c > delete mode 100644 arch/arm/mach-shmobile/include/mach/head-ap4evb.txt > delete mode 100644 arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h > > diff --git a/arch/arm/configs/ap4evb_defconfig b/arch/arm/configs/ap4evb_defconfig > deleted file mode 100644 > index 66894f7..0000000 > --- a/arch/arm/configs/ap4evb_defconfig > +++ /dev/null > @@ -1,56 +0,0 @@ > -CONFIG_EXPERIMENTAL=y > -CONFIG_SYSVIPC=y > -CONFIG_IKCONFIG=y > -CONFIG_IKCONFIG_PROC=y > -CONFIG_LOG_BUF_SHIFT=16 > -CONFIG_BLK_DEV_INITRD=y > -CONFIG_SLAB=y > -# CONFIG_BLK_DEV_BSG is not set > -# CONFIG_IOSCHED_DEADLINE is not set > -# CONFIG_IOSCHED_CFQ is not set > -CONFIG_ARCH_SHMOBILE=y > -CONFIG_ARCH_SH7372=y > -CONFIG_MACH_AP4EVB=y > -CONFIG_AEABI=y > -# CONFIG_OABI_COMPAT is not set > -CONFIG_ZBOOT_ROM_TEXT=0x0 > -CONFIG_ZBOOT_ROM_BSS=0x0 > -CONFIG_CMDLINE="console=ttySC0,115200 earlyprintk=sh-sci.0,115200" > -CONFIG_KEXEC=y > -CONFIG_PM=y > -# CONFIG_SUSPEND is not set > -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" > -# CONFIG_FIRMWARE_IN_KERNEL is not set > -CONFIG_MTD=y > -CONFIG_MTD_CONCAT=y > -CONFIG_MTD_PARTITIONS=y > -CONFIG_MTD_CHAR=y > -CONFIG_MTD_BLOCK=y > -CONFIG_MTD_CFI=y > -CONFIG_MTD_CFI_INTELEXT=y > -CONFIG_MTD_PHYSMAP=y > -CONFIG_MTD_NAND=y > -# CONFIG_BLK_DEV is not set > -# CONFIG_MISC_DEVICES is not set > -# CONFIG_INPUT_MOUSEDEV_PSAUX is not set > -# CONFIG_INPUT_KEYBOARD is not set > -# CONFIG_INPUT_MOUSE is not set > -# CONFIG_SERIO is not set > -CONFIG_SERIAL_SH_SCI=y > -CONFIG_SERIAL_SH_SCI_NR_UARTS=8 > -CONFIG_SERIAL_SH_SCI_CONSOLE=y > -# CONFIG_LEGACY_PTYS is not set > -# CONFIG_HW_RANDOM is not set > -# CONFIG_HWMON is not set > -# CONFIG_VGA_CONSOLE is not set > -# CONFIG_HID_SUPPORT is not set > -# CONFIG_USB_SUPPORT is not set > -# CONFIG_DNOTIFY is not set > -CONFIG_TMPFS=y > -# CONFIG_MISC_FILESYSTEMS is not set > -CONFIG_MAGIC_SYSRQ=y > -CONFIG_DEBUG_KERNEL=y > -# CONFIG_DETECT_SOFTLOCKUP is not set > -# CONFIG_RCU_CPU_STALL_DETECTOR is not set > -# CONFIG_FTRACE is not set > -# CONFIG_CRC32 is not set > diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig > index 747f68a..ae1a530 100644 > --- a/arch/arm/mach-shmobile/Kconfig > +++ b/arch/arm/mach-shmobile/Kconfig > @@ -69,27 +69,6 @@ config ARCH_EMEV2 > > comment "SH-Mobile Board Type" > > -config MACH_AP4EVB > - bool "AP4EVB board" > - depends on ARCH_SH7372 > - select ARCH_REQUIRE_GPIOLIB > - select REGULATOR_FIXED_VOLTAGE if REGULATOR > - select SH_LCD_MIPI_DSI > - select SND_SOC_AK4642 if SND_SIMPLE_CARD > - > -choice > - prompt "AP4EVB LCD panel selection" > - default AP4EVB_QHD > - depends on MACH_AP4EVB > - > -config AP4EVB_QHD > - bool "MIPI-DSI QHD (960x540)" > - > -config AP4EVB_WVGA > - bool "Parallel WVGA (800x480)" > - > -endchoice > - > config MACH_AG5EVM > bool "AG5EVM board" > depends on ARCH_SH73A0 > diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile > index 068f1da..aae28f3 100644 > --- a/arch/arm/mach-shmobile/Makefile > +++ b/arch/arm/mach-shmobile/Makefile > @@ -35,7 +35,6 @@ obj-$(CONFIG_ARCH_R8A7779) += pm-r8a7779.o > obj-$(CONFIG_ARCH_SH73A0) += pm-sh73a0.o > > # Board objects > -obj-$(CONFIG_MACH_AP4EVB) += board-ap4evb.o > obj-$(CONFIG_MACH_AG5EVM) += board-ag5evm.o > obj-$(CONFIG_MACH_APE6EVM) += board-ape6evm.o > obj-$(CONFIG_MACH_MACKEREL) += board-mackerel.o > diff --git a/arch/arm/mach-shmobile/Makefile.boot b/arch/arm/mach-shmobile/Makefile.boot > index 6b147ea..3030673 100644 > --- a/arch/arm/mach-shmobile/Makefile.boot > +++ b/arch/arm/mach-shmobile/Makefile.boot > @@ -1,7 +1,6 @@ > # per-board load address for uImage > loadaddr-y := > loadaddr-$(CONFIG_MACH_AG5EVM) += 0x40008000 > -loadaddr-$(CONFIG_MACH_AP4EVB) += 0x40008000 > loadaddr-$(CONFIG_MACH_APE6EVM) += 0x40008000 > loadaddr-$(CONFIG_MACH_ARMADILLO800EVA) += 0x40008000 > loadaddr-$(CONFIG_MACH_ARMADILLO800EVA_REFERENCE) += 0x40008000 > diff --git a/arch/arm/mach-shmobile/board-ap4evb.c b/arch/arm/mach-shmobile/board-ap4evb.c > deleted file mode 100644 > index 297bf5e..0000000 > --- a/arch/arm/mach-shmobile/board-ap4evb.c > +++ /dev/null > @@ -1,1310 +0,0 @@ > -/* > - * AP4EVB board support > - * > - * Copyright (C) 2010 Magnus Damm > - * Copyright (C) 2008 Yoshihiro Shimoda > - * > - * This program is free software; you can redistribute it and/or modify > - * it under the terms of the GNU General Public License as published by > - * the Free Software Foundation; version 2 of the License. > - * > - * This program is distributed in the hope that it will be useful, > - * but WITHOUT ANY WARRANTY; without even the implied warranty of > - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > - * GNU General Public License for more details. > - * > - * You should have received a copy of the GNU General Public License > - * along with this program; if not, write to the Free Software > - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA > - */ > -#include <linux/clk.h> > -#include <linux/kernel.h> > -#include <linux/init.h> > -#include <linux/interrupt.h> > -#include <linux/irq.h> > -#include <linux/platform_device.h> > -#include <linux/delay.h> > -#include <linux/mfd/tmio.h> > -#include <linux/mmc/host.h> > -#include <linux/mmc/sh_mobile_sdhi.h> > -#include <linux/mtd/mtd.h> > -#include <linux/mtd/partitions.h> > -#include <linux/mtd/physmap.h> > -#include <linux/mmc/sh_mmcif.h> > -#include <linux/i2c.h> > -#include <linux/i2c/tsc2007.h> > -#include <linux/io.h> > -#include <linux/pinctrl/machine.h> > -#include <linux/regulator/fixed.h> > -#include <linux/regulator/machine.h> > -#include <linux/smsc911x.h> > -#include <linux/sh_intc.h> > -#include <linux/sh_clk.h> > -#include <linux/gpio.h> > -#include <linux/input.h> > -#include <linux/leds.h> > -#include <linux/input/sh_keysc.h> > -#include <linux/usb/r8a66597.h> > -#include <linux/pm_clock.h> > -#include <linux/dma-mapping.h> > - > -#include <media/sh_mobile_ceu.h> > -#include <media/sh_mobile_csi2.h> > -#include <media/soc_camera.h> > - > -#include <sound/sh_fsi.h> > -#include <sound/simple_card.h> > - > -#include <video/sh_mobile_hdmi.h> > -#include <video/sh_mobile_lcdc.h> > -#include <video/sh_mipi_dsi.h> > - > -#include <mach/common.h> > -#include <mach/irqs.h> > -#include <mach/sh7372.h> > - > -#include <asm/mach-types.h> > -#include <asm/mach/arch.h> > -#include <asm/setup.h> > - > -#include "sh-gpio.h" > - > -/* > - * Address Interface BusWidth note > - * ------------------------------------------------------------------ > - * 0x0000_0000 NOR Flash ROM (MCP) 16bit SW7 : bit1 = ON > - * 0x0800_0000 user area - > - * 0x1000_0000 NOR Flash ROM (MCP) 16bit SW7 : bit1 = OFF > - * 0x1400_0000 Ether (LAN9220) 16bit > - * 0x1600_0000 user area - cannot use with NAND > - * 0x1800_0000 user area - > - * 0x1A00_0000 - > - * 0x4000_0000 LPDDR2-SDRAM (POP) 32bit > - */ > - > -/* > - * NOR Flash ROM > - * > - * SW1 | SW2 | SW7 | NOR Flash ROM > - * bit1 | bit1 bit2 | bit1 | Memory allocation > - * ------+------------+------+------------------ > - * OFF | ON OFF | ON | Area 0 > - * OFF | ON OFF | OFF | Area 4 > - */ > - > -/* > - * NAND Flash ROM > - * > - * SW1 | SW2 | SW7 | NAND Flash ROM > - * bit1 | bit1 bit2 | bit2 | Memory allocation > - * ------+------------+------+------------------ > - * OFF | ON OFF | ON | FCE 0 > - * OFF | ON OFF | OFF | FCE 1 > - */ > - > -/* > - * SMSC 9220 > - * > - * SW1 SMSC 9220 > - * ----------------------- > - * ON access disable > - * OFF access enable > - */ > - > -/* > - * LCD / IRQ / KEYSC / IrDA > - * > - * IRQ = IRQ26 (TS), IRQ27 (VIO), IRQ28 (QHD-TouchScreen) > - * LCD = 2nd LCDC (WVGA) > - * > - * | SW43 | > - * SW3 | ON | OFF | > - * -------------+-----------------------+---------------+ > - * ON | KEY / IrDA | LCD | > - * OFF | KEY / IrDA / IRQ | IRQ | > - * > - * > - * QHD / WVGA display > - * > - * You can choice display type on menuconfig. > - * Then, check above dip-switch. > - */ > - > -/* > - * USB > - * > - * J7 : 1-2 MAX3355E VBUS > - * 2-3 DC 5.0V > - * > - * S39: bit2: off > - */ > - > -/* > - * FSI/FSMI > - * > - * SW41 : ON : SH-Mobile AP4 Audio Mode > - * : OFF : Bluetooth Audio Mode > - * > - * it needs amixer settings for playing > - * > - * amixer set "Headphone Enable" on > - */ > - > -/* > - * MMC0/SDHI1 (CN7) > - * > - * J22 : select card voltage > - * 1-2 pin : 1.8v > - * 2-3 pin : 3.3v > - * > - * SW1 | SW33 > - * | bit1 | bit2 | bit3 | bit4 > - * ------------+------+------+------+------- > - * MMC0 OFF | OFF | ON | ON | X > - * SDHI1 OFF | ON | X | OFF | ON > - * > - * voltage lebel > - * CN7 : 1.8v > - * CN12: 3.3v > - */ > - > -/* Dummy supplies, where voltage doesn't matter */ > -static struct regulator_consumer_supply fixed1v8_power_consumers[] = > -{ > - /* J22 default position: 1.8V */ > - REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"), > - REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"), > - REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"), > - REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"), > -}; > - > -static struct regulator_consumer_supply fixed3v3_power_consumers[] = > -{ > - REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"), > - REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"), > -}; > - > -static struct regulator_consumer_supply dummy_supplies[] = { > - REGULATOR_SUPPLY("vddvario", "smsc911x"), > - REGULATOR_SUPPLY("vdd33a", "smsc911x"), > -}; > - > -/* MTD */ > -static struct mtd_partition nor_flash_partitions[] = { > - { > - .name = "loader", > - .offset = 0x00000000, > - .size = 512 * 1024, > - .mask_flags = MTD_WRITEABLE, > - }, > - { > - .name = "bootenv", > - .offset = MTDPART_OFS_APPEND, > - .size = 512 * 1024, > - .mask_flags = MTD_WRITEABLE, > - }, > - { > - .name = "kernel_ro", > - .offset = MTDPART_OFS_APPEND, > - .size = 8 * 1024 * 1024, > - .mask_flags = MTD_WRITEABLE, > - }, > - { > - .name = "kernel", > - .offset = MTDPART_OFS_APPEND, > - .size = 8 * 1024 * 1024, > - }, > - { > - .name = "data", > - .offset = MTDPART_OFS_APPEND, > - .size = MTDPART_SIZ_FULL, > - }, > -}; > - > -static struct physmap_flash_data nor_flash_data = { > - .width = 2, > - .parts = nor_flash_partitions, > - .nr_parts = ARRAY_SIZE(nor_flash_partitions), > -}; > - > -static struct resource nor_flash_resources[] = { > - [0] = { > - .start = 0x20000000, /* CS0 shadow instead of regular CS0 */ > - .end = 0x28000000 - 1, /* needed by USB MASK ROM boot */ > - .flags = IORESOURCE_MEM, > - } > -}; > - > -static struct platform_device nor_flash_device = { > - .name = "physmap-flash", > - .dev = { > - .platform_data = &nor_flash_data, > - }, > - .num_resources = ARRAY_SIZE(nor_flash_resources), > - .resource = nor_flash_resources, > -}; > - > -/* SMSC 9220 */ > -static struct resource smc911x_resources[] = { > - { > - .start = 0x14000000, > - .end = 0x16000000 - 1, > - .flags = IORESOURCE_MEM, > - }, { > - .start = evt2irq(0x02c0) /* IRQ6A */, > - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, > - }, > -}; > - > -static struct smsc911x_platform_config smsc911x_info = { > - .flags = SMSC911X_USE_16BIT | SMSC911X_SAVE_MAC_ADDRESS, > - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, > - .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL, > -}; > - > -static struct platform_device smc911x_device = { > - .name = "smsc911x", > - .id = -1, > - .num_resources = ARRAY_SIZE(smc911x_resources), > - .resource = smc911x_resources, > - .dev = { > - .platform_data = &smsc911x_info, > - }, > -}; > - > -/* > - * The card detect pin of the top SD/MMC slot (CN7) is active low and is > - * connected to GPIO A22 of SH7372 (GPIO 41). > - */ > -static int slot_cn7_get_cd(struct platform_device *pdev) > -{ > - return !gpio_get_value(41); > -} > -/* MERAM */ > -static struct sh_mobile_meram_info meram_info = { > - .addr_mode = SH_MOBILE_MERAM_MODE1, > -}; > - > -static struct resource meram_resources[] = { > - [0] = { > - .name = "regs", > - .start = 0xe8000000, > - .end = 0xe807ffff, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .name = "meram", > - .start = 0xe8080000, > - .end = 0xe81fffff, > - .flags = IORESOURCE_MEM, > - }, > -}; > - > -static struct platform_device meram_device = { > - .name = "sh_mobile_meram", > - .id = 0, > - .num_resources = ARRAY_SIZE(meram_resources), > - .resource = meram_resources, > - .dev = { > - .platform_data = &meram_info, > - }, > -}; > - > -/* SH_MMCIF */ > -static struct resource sh_mmcif_resources[] = { > - [0] = { > - .name = "MMCIF", > - .start = 0xE6BD0000, > - .end = 0xE6BD00FF, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - /* MMC ERR */ > - .start = evt2irq(0x1ac0), > - .flags = IORESOURCE_IRQ, > - }, > - [2] = { > - /* MMC NOR */ > - .start = evt2irq(0x1ae0), > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct sh_mmcif_plat_data sh_mmcif_plat = { > - .sup_pclk = 0, > - .ocr = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34, > - .caps = MMC_CAP_4_BIT_DATA | > - MMC_CAP_8_BIT_DATA | > - MMC_CAP_NEEDS_POLL, > - .get_cd = slot_cn7_get_cd, > - .slave_id_tx = SHDMA_SLAVE_MMCIF_TX, > - .slave_id_rx = SHDMA_SLAVE_MMCIF_RX, > -}; > - > -static struct platform_device sh_mmcif_device = { > - .name = "sh_mmcif", > - .id = 0, > - .dev = { > - .dma_mask = NULL, > - .coherent_dma_mask = 0xffffffff, > - .platform_data = &sh_mmcif_plat, > - }, > - .num_resources = ARRAY_SIZE(sh_mmcif_resources), > - .resource = sh_mmcif_resources, > -}; > - > -/* SDHI0 */ > -static struct sh_mobile_sdhi_info sdhi0_info = { > - .dma_slave_tx = SHDMA_SLAVE_SDHI0_TX, > - .dma_slave_rx = SHDMA_SLAVE_SDHI0_RX, > - .tmio_caps = MMC_CAP_SDIO_IRQ, > -}; > - > -static struct resource sdhi0_resources[] = { > - [0] = { > - .name = "SDHI0", > - .start = 0xe6850000, > - .end = 0xe68500ff, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = evt2irq(0x0e00) /* SDHI0_SDHI0I0 */, > - .flags = IORESOURCE_IRQ, > - }, > - [2] = { > - .start = evt2irq(0x0e20) /* SDHI0_SDHI0I1 */, > - .flags = IORESOURCE_IRQ, > - }, > - [3] = { > - .start = evt2irq(0x0e40) /* SDHI0_SDHI0I2 */, > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct platform_device sdhi0_device = { > - .name = "sh_mobile_sdhi", > - .num_resources = ARRAY_SIZE(sdhi0_resources), > - .resource = sdhi0_resources, > - .id = 0, > - .dev = { > - .platform_data = &sdhi0_info, > - }, > -}; > - > -/* SDHI1 */ > -static struct sh_mobile_sdhi_info sdhi1_info = { > - .dma_slave_tx = SHDMA_SLAVE_SDHI1_TX, > - .dma_slave_rx = SHDMA_SLAVE_SDHI1_RX, > - .tmio_ocr_mask = MMC_VDD_165_195, > - .tmio_flags = TMIO_MMC_WRPROTECT_DISABLE, > - .tmio_caps = MMC_CAP_NEEDS_POLL | MMC_CAP_SDIO_IRQ, > - .get_cd = slot_cn7_get_cd, > -}; > - > -static struct resource sdhi1_resources[] = { > - [0] = { > - .name = "SDHI1", > - .start = 0xe6860000, > - .end = 0xe68600ff, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = evt2irq(0x0e80), /* SDHI1_SDHI1I0 */ > - .flags = IORESOURCE_IRQ, > - }, > - [2] = { > - .start = evt2irq(0x0ea0), /* SDHI1_SDHI1I1 */ > - .flags = IORESOURCE_IRQ, > - }, > - [3] = { > - .start = evt2irq(0x0ec0), /* SDHI1_SDHI1I2 */ > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct platform_device sdhi1_device = { > - .name = "sh_mobile_sdhi", > - .num_resources = ARRAY_SIZE(sdhi1_resources), > - .resource = sdhi1_resources, > - .id = 1, > - .dev = { > - .platform_data = &sdhi1_info, > - }, > -}; > - > -/* USB1 */ > -static void usb1_host_port_power(int port, int power) > -{ > - if (!power) /* only power-on supported for now */ > - return; > - > - /* set VBOUT/PWEN and EXTLP1 in DVSTCTR */ > - __raw_writew(__raw_readw(IOMEM(0xE68B0008)) | 0x600, IOMEM(0xE68B0008)); > -} > - > -static struct r8a66597_platdata usb1_host_data = { > - .on_chip = 1, > - .port_power = usb1_host_port_power, > -}; > - > -static struct resource usb1_host_resources[] = { > - [0] = { > - .name = "USBHS", > - .start = 0xE68B0000, > - .end = 0xE68B00E6 - 1, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = evt2irq(0x1ce0) /* USB1_USB1I0 */, > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct platform_device usb1_host_device = { > - .name = "r8a66597_hcd", > - .id = 1, > - .dev = { > - .dma_mask = NULL, /* not use dma */ > - .coherent_dma_mask = 0xffffffff, > - .platform_data = &usb1_host_data, > - }, > - .num_resources = ARRAY_SIZE(usb1_host_resources), > - .resource = usb1_host_resources, > -}; > - > -/* > - * QHD display > - */ > -#ifdef CONFIG_AP4EVB_QHD > - > -/* KEYSC (Needs SW43 set to ON) */ > -static struct sh_keysc_info keysc_info = { > - .mode = SH_KEYSC_MODE_1, > - .scan_timing = 3, > - .delay = 2500, > - .keycodes = { > - KEY_0, KEY_1, KEY_2, KEY_3, KEY_4, > - KEY_5, KEY_6, KEY_7, KEY_8, KEY_9, > - KEY_A, KEY_B, KEY_C, KEY_D, KEY_E, > - KEY_F, KEY_G, KEY_H, KEY_I, KEY_J, > - KEY_K, KEY_L, KEY_M, KEY_N, KEY_O, > - }, > -}; > - > -static struct resource keysc_resources[] = { > - [0] = { > - .name = "KEYSC", > - .start = 0xe61b0000, > - .end = 0xe61b0063, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = evt2irq(0x0be0), /* KEYSC_KEY */ > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct platform_device keysc_device = { > - .name = "sh_keysc", > - .id = 0, /* "keysc0" clock */ > - .num_resources = ARRAY_SIZE(keysc_resources), > - .resource = keysc_resources, > - .dev = { > - .platform_data = &keysc_info, > - }, > -}; > - > -/* MIPI-DSI */ > -static int sh_mipi_set_dot_clock(struct platform_device *pdev, > - void __iomem *base, > - int enable) > -{ > - struct clk *pck = clk_get(&pdev->dev, "dsip_clk"); > - > - if (IS_ERR(pck)) > - return PTR_ERR(pck); > - > - if (enable) { > - /* > - * DSIPCLK = 24MHz > - * D-PHY = DSIPCLK * ((0x6*2)+1) = 312MHz (see .phyctrl) > - * HsByteCLK = D-PHY/8 = 39MHz > - * > - * X * Y * FPS = > - * (544+72+600+16) * (961+8+8+2) * 30 = 36.1MHz > - */ > - clk_set_rate(pck, clk_round_rate(pck, 24000000)); > - clk_enable(pck); > - } else { > - clk_disable(pck); > - } > - > - clk_put(pck); > - > - return 0; > -} > - > -static struct resource mipidsi0_resources[] = { > - [0] = { > - .start = 0xffc60000, > - .end = 0xffc63073, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = 0xffc68000, > - .end = 0xffc680ef, > - .flags = IORESOURCE_MEM, > - }, > -}; > - > -static struct sh_mipi_dsi_info mipidsi0_info = { > - .data_format = MIPI_RGB888, > - .channel = LCDC_CHAN_MAINLCD, > - .lane = 2, > - .vsynw_offset = 17, > - .phyctrl = 0x6 << 8, > - .flags = SH_MIPI_DSI_SYNC_PULSES_MODE | > - SH_MIPI_DSI_HSbyteCLK, > - .set_dot_clock = sh_mipi_set_dot_clock, > -}; > - > -static struct platform_device mipidsi0_device = { > - .name = "sh-mipi-dsi", > - .num_resources = ARRAY_SIZE(mipidsi0_resources), > - .resource = mipidsi0_resources, > - .id = 0, > - .dev = { > - .platform_data = &mipidsi0_info, > - }, > -}; > - > -static struct platform_device *qhd_devices[] __initdata = { > - &mipidsi0_device, > - &keysc_device, > -}; > -#endif /* CONFIG_AP4EVB_QHD */ > - > -/* LCDC0 */ > -static const struct fb_videomode ap4evb_lcdc_modes[] = { > - { > -#ifdef CONFIG_AP4EVB_QHD > - .name = "R63302(QHD)", > - .xres = 544, > - .yres = 961, > - .left_margin = 72, > - .right_margin = 600, > - .hsync_len = 16, > - .upper_margin = 8, > - .lower_margin = 8, > - .vsync_len = 2, > - .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT, > -#else > - .name = "WVGA Panel", > - .xres = 800, > - .yres = 480, > - .left_margin = 220, > - .right_margin = 110, > - .hsync_len = 70, > - .upper_margin = 20, > - .lower_margin = 5, > - .vsync_len = 5, > - .sync = 0, > -#endif > - }, > -}; > - > -static const struct sh_mobile_meram_cfg lcd_meram_cfg = { > - .icb[0] = { > - .meram_size = 0x40, > - }, > - .icb[1] = { > - .meram_size = 0x40, > - }, > -}; > - > -static struct sh_mobile_lcdc_info lcdc_info = { > - .meram_dev = &meram_info, > - .ch[0] = { > - .chan = LCDC_CHAN_MAINLCD, > - .fourcc = V4L2_PIX_FMT_RGB565, > - .lcd_modes = ap4evb_lcdc_modes, > - .num_modes = ARRAY_SIZE(ap4evb_lcdc_modes), > - .meram_cfg = &lcd_meram_cfg, > -#ifdef CONFIG_AP4EVB_QHD > - .tx_dev = &mipidsi0_device, > -#endif > - } > -}; > - > -static struct resource lcdc_resources[] = { > - [0] = { > - .name = "LCDC", > - .start = 0xfe940000, /* P4-only space */ > - .end = 0xfe943fff, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = intcs_evt2irq(0x580), > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct platform_device lcdc_device = { > - .name = "sh_mobile_lcdc_fb", > - .num_resources = ARRAY_SIZE(lcdc_resources), > - .resource = lcdc_resources, > - .dev = { > - .platform_data = &lcdc_info, > - .coherent_dma_mask = ~0, > - }, > -}; > - > -/* FSI */ > -#define IRQ_FSI evt2irq(0x1840) > -static struct sh_fsi_platform_info fsi_info = { > - .port_b = { > - .flags = SH_FSI_CLK_CPG | > - SH_FSI_FMT_SPDIF, > - }, > -}; > - > -static struct resource fsi_resources[] = { > - [0] = { > - .name = "FSI", > - .start = 0xFE3C0000, > - .end = 0xFE3C0400 - 1, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = IRQ_FSI, > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct platform_device fsi_device = { > - .name = "sh_fsi2", > - .id = -1, > - .num_resources = ARRAY_SIZE(fsi_resources), > - .resource = fsi_resources, > - .dev = { > - .platform_data = &fsi_info, > - }, > -}; > - > -static struct asoc_simple_card_info fsi2_ak4643_info = { > - .name = "AK4643", > - .card = "FSI2A-AK4643", > - .codec = "ak4642-codec.0-0013", > - .platform = "sh_fsi2", > - .daifmt = SND_SOC_DAIFMT_LEFT_J, > - .cpu_dai = { > - .name = "fsia-dai", > - .fmt = SND_SOC_DAIFMT_CBS_CFS, > - }, > - .codec_dai = { > - .name = "ak4642-hifi", > - .fmt = SND_SOC_DAIFMT_CBM_CFM, > - .sysclk = 11289600, > - }, > -}; > - > -static struct platform_device fsi_ak4643_device = { > - .name = "asoc-simple-card", > - .dev = { > - .platform_data = &fsi2_ak4643_info, > - }, > -}; > - > -/* LCDC1 */ > -static long ap4evb_clk_optimize(unsigned long target, unsigned long *best_freq, > - unsigned long *parent_freq); > - > -static struct sh_mobile_hdmi_info hdmi_info = { > - .flags = HDMI_SND_SRC_SPDIF, > - .clk_optimize_parent = ap4evb_clk_optimize, > -}; > - > -static struct resource hdmi_resources[] = { > - [0] = { > - .name = "HDMI", > - .start = 0xe6be0000, > - .end = 0xe6be00ff, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - /* There's also an HDMI interrupt on INTCS @ 0x18e0 */ > - .start = evt2irq(0x17e0), > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct platform_device hdmi_device = { > - .name = "sh-mobile-hdmi", > - .num_resources = ARRAY_SIZE(hdmi_resources), > - .resource = hdmi_resources, > - .id = -1, > - .dev = { > - .platform_data = &hdmi_info, > - }, > -}; > - > -static long ap4evb_clk_optimize(unsigned long target, unsigned long *best_freq, > - unsigned long *parent_freq) > -{ > - struct clk *hdmi_ick = clk_get(&hdmi_device.dev, "ick"); > - long error; > - > - if (IS_ERR(hdmi_ick)) { > - int ret = PTR_ERR(hdmi_ick); > - pr_err("Cannot get HDMI ICK: %d\n", ret); > - return ret; > - } > - > - error = clk_round_parent(hdmi_ick, target, best_freq, parent_freq, 1, 64); > - > - clk_put(hdmi_ick); > - > - return error; > -} > - > -static const struct sh_mobile_meram_cfg hdmi_meram_cfg = { > - .icb[0] = { > - .meram_size = 0x100, > - }, > - .icb[1] = { > - .meram_size = 0x100, > - }, > -}; > - > -static struct sh_mobile_lcdc_info sh_mobile_lcdc1_info = { > - .clock_source = LCDC_CLK_EXTERNAL, > - .meram_dev = &meram_info, > - .ch[0] = { > - .chan = LCDC_CHAN_MAINLCD, > - .fourcc = V4L2_PIX_FMT_RGB565, > - .interface_type = RGB24, > - .clock_divider = 1, > - .flags = LCDC_FLAGS_DWPOL, > - .meram_cfg = &hdmi_meram_cfg, > - .tx_dev = &hdmi_device, > - } > -}; > - > -static struct resource lcdc1_resources[] = { > - [0] = { > - .name = "LCDC1", > - .start = 0xfe944000, > - .end = 0xfe947fff, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = intcs_evt2irq(0x1780), > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct platform_device lcdc1_device = { > - .name = "sh_mobile_lcdc_fb", > - .num_resources = ARRAY_SIZE(lcdc1_resources), > - .resource = lcdc1_resources, > - .id = 1, > - .dev = { > - .platform_data = &sh_mobile_lcdc1_info, > - .coherent_dma_mask = ~0, > - }, > -}; > - > -static struct asoc_simple_card_info fsi2_hdmi_info = { > - .name = "HDMI", > - .card = "FSI2B-HDMI", > - .codec = "sh-mobile-hdmi", > - .platform = "sh_fsi2", > - .cpu_dai = { > - .name = "fsib-dai", > - .fmt = SND_SOC_DAIFMT_CBM_CFM | SND_SOC_DAIFMT_IB_NF, > - }, > - .codec_dai = { > - .name = "sh_mobile_hdmi-hifi", > - }, > -}; > - > -static struct platform_device fsi_hdmi_device = { > - .name = "asoc-simple-card", > - .id = 1, > - .dev = { > - .platform_data = &fsi2_hdmi_info, > - }, > -}; > - > -static struct gpio_led ap4evb_leds[] = { > - { > - .name = "led4", > - .gpio = 185, > - .default_state = LEDS_GPIO_DEFSTATE_ON, > - }, > - { > - .name = "led2", > - .gpio = 186, > - .default_state = LEDS_GPIO_DEFSTATE_ON, > - }, > - { > - .name = "led3", > - .gpio = 187, > - .default_state = LEDS_GPIO_DEFSTATE_ON, > - }, > - { > - .name = "led1", > - .gpio = 188, > - .default_state = LEDS_GPIO_DEFSTATE_ON, > - } > -}; > - > -static struct gpio_led_platform_data ap4evb_leds_pdata = { > - .num_leds = ARRAY_SIZE(ap4evb_leds), > - .leds = ap4evb_leds, > -}; > - > -static struct platform_device leds_device = { > - .name = "leds-gpio", > - .id = 0, > - .dev = { > - .platform_data = &ap4evb_leds_pdata, > - }, > -}; > - > -static struct i2c_board_info imx074_info = { > - I2C_BOARD_INFO("imx074", 0x1a), > -}; > - > -static struct soc_camera_link imx074_link = { > - .bus_id = 0, > - .board_info = &imx074_info, > - .i2c_adapter_id = 0, > - .module_name = "imx074", > -}; > - > -static struct platform_device ap4evb_camera = { > - .name = "soc-camera-pdrv", > - .id = 0, > - .dev = { > - .platform_data = &imx074_link, > - }, > -}; > - > -static struct sh_csi2_client_config csi2_clients[] = { > - { > - .phy = SH_CSI2_PHY_MAIN, > - .lanes = 0, /* default: 2 lanes */ > - .channel = 0, > - .pdev = &ap4evb_camera, > - }, > -}; > - > -static struct sh_csi2_pdata csi2_info = { > - .type = SH_CSI2C, > - .clients = csi2_clients, > - .num_clients = ARRAY_SIZE(csi2_clients), > - .flags = SH_CSI2_ECC | SH_CSI2_CRC, > -}; > - > -static struct resource csi2_resources[] = { > - [0] = { > - .name = "CSI2", > - .start = 0xffc90000, > - .end = 0xffc90fff, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = intcs_evt2irq(0x17a0), > - .flags = IORESOURCE_IRQ, > - }, > -}; > - > -static struct sh_mobile_ceu_companion csi2 = { > - .id = 0, > - .num_resources = ARRAY_SIZE(csi2_resources), > - .resource = csi2_resources, > - .platform_data = &csi2_info, > -}; > - > -static struct sh_mobile_ceu_info sh_mobile_ceu_info = { > - .flags = SH_CEU_FLAG_USE_8BIT_BUS, > - .max_width = 8188, > - .max_height = 8188, > - .csi2 = &csi2, > -}; > - > -static struct resource ceu_resources[] = { > - [0] = { > - .name = "CEU", > - .start = 0xfe910000, > - .end = 0xfe91009f, > - .flags = IORESOURCE_MEM, > - }, > - [1] = { > - .start = intcs_evt2irq(0x880), > - .flags = IORESOURCE_IRQ, > - }, > - [2] = { > - /* place holder for contiguous memory */ > - }, > -}; > - > -static struct platform_device ceu_device = { > - .name = "sh_mobile_ceu", > - .id = 0, /* "ceu0" clock */ > - .num_resources = ARRAY_SIZE(ceu_resources), > - .resource = ceu_resources, > - .dev = { > - .platform_data = &sh_mobile_ceu_info, > - .coherent_dma_mask = 0xffffffff, > - }, > -}; > - > -static struct platform_device *ap4evb_devices[] __initdata = { > - &leds_device, > - &nor_flash_device, > - &smc911x_device, > - &sdhi0_device, > - &sdhi1_device, > - &usb1_host_device, > - &fsi_device, > - &fsi_ak4643_device, > - &fsi_hdmi_device, > - &sh_mmcif_device, > - &hdmi_device, > - &lcdc_device, > - &lcdc1_device, > - &ceu_device, > - &ap4evb_camera, > - &meram_device, > -}; > - > -static void __init hdmi_init_pm_clock(void) > -{ > - struct clk *hdmi_ick = clk_get(&hdmi_device.dev, "ick"); > - int ret; > - long rate; > - > - if (IS_ERR(hdmi_ick)) { > - ret = PTR_ERR(hdmi_ick); > - pr_err("Cannot get HDMI ICK: %d\n", ret); > - goto out; > - } > - > - ret = clk_set_parent(&sh7372_pllc2_clk, &sh7372_dv_clki_div2_clk); > - if (ret < 0) { > - pr_err("Cannot set PLLC2 parent: %d, %d users\n", ret, sh7372_pllc2_clk.usecount); > - goto out; > - } > - > - pr_debug("PLLC2 initial frequency %lu\n", clk_get_rate(&sh7372_pllc2_clk)); > - > - rate = clk_round_rate(&sh7372_pllc2_clk, 594000000); > - if (rate < 0) { > - pr_err("Cannot get suitable rate: %ld\n", rate); > - ret = rate; > - goto out; > - } > - > - ret = clk_set_rate(&sh7372_pllc2_clk, rate); > - if (ret < 0) { > - pr_err("Cannot set rate %ld: %d\n", rate, ret); > - goto out; > - } > - > - pr_debug("PLLC2 set frequency %lu\n", rate); > - > - ret = clk_set_parent(hdmi_ick, &sh7372_pllc2_clk); > - if (ret < 0) > - pr_err("Cannot set HDMI parent: %d\n", ret); > - > -out: > - if (!IS_ERR(hdmi_ick)) > - clk_put(hdmi_ick); > -} > - > -/* TouchScreen */ > -#ifdef CONFIG_AP4EVB_QHD > -# define GPIO_TSC_PORT 123 > -#else /* WVGA */ > -# define GPIO_TSC_PORT 40 > -#endif > - > -#define IRQ28 evt2irq(0x3380) /* IRQ28A */ > -#define IRQ7 evt2irq(0x02e0) /* IRQ7A */ > -static int ts_get_pendown_state(void) > -{ > - return !gpio_get_value(GPIO_TSC_PORT); > -} > - > -static int ts_init(void) > -{ > - gpio_request_one(GPIO_TSC_PORT, GPIOF_IN, NULL); > - > - return 0; > -} > - > -static struct tsc2007_platform_data tsc2007_info = { > - .model = 2007, > - .x_plate_ohms = 180, > - .get_pendown_state = ts_get_pendown_state, > - .init_platform_hw = ts_init, > -}; > - > -static struct i2c_board_info tsc_device = { > - I2C_BOARD_INFO("tsc2007", 0x48), > - .type = "tsc2007", > - .platform_data = &tsc2007_info, > - /*.irq is selected on ap4evb_init */ > -}; > - > -/* I2C */ > -static struct i2c_board_info i2c0_devices[] = { > - { > - I2C_BOARD_INFO("ak4643", 0x13), > - }, > -}; > - > -static struct i2c_board_info i2c1_devices[] = { > - { > - I2C_BOARD_INFO("r2025sd", 0x32), > - }, > -}; > - > - > -static const struct pinctrl_map ap4evb_pinctrl_map[] = { > - /* CEU */ > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-sh7372", > - "ceu_clk_0", "ceu"), > - /* FSIA (AK4643) */ > - PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-sh7372", > - "fsia_sclk_in", "fsia"), > - PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-sh7372", > - "fsia_data_in", "fsia"), > - PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-sh7372", > - "fsia_data_out", "fsia"), > - /* FSIB (HDMI) */ > - PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.1", "pfc-sh7372", > - "fsib_mclk_in", "fsib"), > - /* HDMI */ > - PIN_MAP_MUX_GROUP_DEFAULT("sh-mobile-hdmi", "pfc-sh7372", > - "hdmi", "hdmi"), > - /* KEYSC */ > - PIN_MAP_MUX_GROUP_DEFAULT("sh_keysc", "pfc-sh7372", > - "keysc_in04_0", "keysc"), > - PIN_MAP_MUX_GROUP_DEFAULT("sh_keysc", "pfc-sh7372", > - "keysc_out5", "keysc"), > -#ifndef CONFIG_AP4EVB_QHD > - /* LCDC */ > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh7372", > - "lcd_data18", "lcd"), > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh7372", > - "lcd_sync", "lcd"), > -#endif > - /* MMCIF */ > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh7372", > - "mmc0_data8_0", "mmc0"), > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh7372", > - "mmc0_ctrl_0", "mmc0"), > - /* SCIFA0 */ > - PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.0", "pfc-sh7372", > - "scifa0_data", "scifa0"), > - /* SDHI0 */ > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372", > - "sdhi0_data4", "sdhi0"), > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372", > - "sdhi0_ctrl", "sdhi0"), > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372", > - "sdhi0_cd", "sdhi0"), > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372", > - "sdhi0_wp", "sdhi0"), > - /* SDHI1 */ > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-sh7372", > - "sdhi1_data4", "sdhi1"), > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-sh7372", > - "sdhi1_ctrl", "sdhi1"), > - /* SMSC911X */ > - PIN_MAP_MUX_GROUP_DEFAULT("smsc911x", "pfc-sh7372", > - "bsc_cs5a", "bsc"), > - PIN_MAP_MUX_GROUP_DEFAULT("smsc911x", "pfc-sh7372", > - "intc_irq6_0", "intc"), > - /* TSC2007 */ > -#ifdef CONFIG_AP4EVB_QHD > - PIN_MAP_MUX_GROUP_DEFAULT("1-0048", "pfc-sh7372", > - "intc_irq28_0", "intc"), > -#else /* WVGA */ > - PIN_MAP_MUX_GROUP_DEFAULT("1-0048", "pfc-sh7372", > - "intc_irq7_0", "intc"), > -#endif > - /* USBHS1 */ > - PIN_MAP_MUX_GROUP_DEFAULT("r8a66597_hcd.1", "pfc-sh7372", > - "usb1_vbus", "usb1"), > - PIN_MAP_MUX_GROUP_DEFAULT("r8a66597_hcd.1", "pfc-sh7372", > - "usb1_otg_id_0", "usb1"), > - PIN_MAP_MUX_GROUP_DEFAULT("r8a66597_hcd.1", "pfc-sh7372", > - "usb1_otg_ctrl_0", "usb1"), > -}; > - > -#define GPIO_PORT9CR IOMEM(0xE6051009) > -#define GPIO_PORT10CR IOMEM(0xE605100A) > -#define USCCR1 IOMEM(0xE6058144) > -static void __init ap4evb_init(void) > -{ > - struct pm_domain_device domain_devices[] = { > - { "A4LC", &lcdc1_device, }, > - { "A4LC", &lcdc_device, }, > - { "A4MP", &fsi_device, }, > - { "A3SP", &sh_mmcif_device, }, > - { "A3SP", &sdhi0_device, }, > - { "A3SP", &sdhi1_device, }, > - { "A4R", &ceu_device, }, > - }; > - u32 srcr4; > - struct clk *clk; > - > - regulator_register_always_on(0, "fixed-1.8V", fixed1v8_power_consumers, > - ARRAY_SIZE(fixed1v8_power_consumers), 1800000); > - regulator_register_always_on(1, "fixed-3.3V", fixed3v3_power_consumers, > - ARRAY_SIZE(fixed3v3_power_consumers), 3300000); > - regulator_register_fixed(2, dummy_supplies, ARRAY_SIZE(dummy_supplies)); > - > - /* External clock source */ > - clk_set_rate(&sh7372_dv_clki_clk, 27000000); > - > - pinctrl_register_mappings(ap4evb_pinctrl_map, > - ARRAY_SIZE(ap4evb_pinctrl_map)); > - sh7372_pinmux_init(); > - > - /* enable Debug switch (S6) */ > - gpio_request_one(32, GPIOF_IN | GPIOF_EXPORT, NULL); > - gpio_request_one(33, GPIOF_IN | GPIOF_EXPORT, NULL); > - gpio_request_one(34, GPIOF_IN | GPIOF_EXPORT, NULL); > - gpio_request_one(35, GPIOF_IN | GPIOF_EXPORT, NULL); > - > - /* setup USB phy */ > - __raw_writew(0x8a0a, IOMEM(0xE6058130)); /* USBCR4 */ > - > - /* FSI2 port A (ak4643) */ > - gpio_request_one(161, GPIOF_OUT_INIT_LOW, NULL); /* slave */ > - > - gpio_request(9, NULL); > - gpio_request(10, NULL); > - gpio_direction_none(GPIO_PORT9CR); /* FSIAOBT needs no direction */ > - gpio_direction_none(GPIO_PORT10CR); /* FSIAOLR needs no direction */ > - > - /* card detect pin for MMC slot (CN7) */ > - gpio_request_one(41, GPIOF_IN, NULL); > - > - /* FSI2 port B (HDMI) */ > - __raw_writew(__raw_readw(USCCR1) & ~(1 << 6), USCCR1); /* use SPDIF */ > - > - /* set SPU2 clock to 119.6 MHz */ > - clk = clk_get(NULL, "spu_clk"); > - if (!IS_ERR(clk)) { > - clk_set_rate(clk, clk_round_rate(clk, 119600000)); > - clk_put(clk); > - } > - > - /* > - * set irq priority, to avoid sound chopping > - * when NFS rootfs is used > - * FSI(3) > SMSC911X(2) > - */ > - intc_set_priority(IRQ_FSI, 3); > - > - i2c_register_board_info(0, i2c0_devices, > - ARRAY_SIZE(i2c0_devices)); > - > - i2c_register_board_info(1, i2c1_devices, > - ARRAY_SIZE(i2c1_devices)); > - > -#ifdef CONFIG_AP4EVB_QHD > - > - /* > - * For QHD Panel (MIPI-DSI, CONFIG_AP4EVB_QHD=y) and > - * IRQ28 for Touch Panel, set dip switches S3, S43 as OFF, ON. > - */ > - > - /* enable TouchScreen */ > - irq_set_irq_type(IRQ28, IRQ_TYPE_LEVEL_LOW); > - > - tsc_device.irq = IRQ28; > - i2c_register_board_info(1, &tsc_device, 1); > - > - /* LCDC0 */ > - lcdc_info.clock_source = LCDC_CLK_PERIPHERAL; > - lcdc_info.ch[0].interface_type = RGB24; > - lcdc_info.ch[0].clock_divider = 1; > - lcdc_info.ch[0].flags = LCDC_FLAGS_DWPOL; > - lcdc_info.ch[0].panel_cfg.width = 44; > - lcdc_info.ch[0].panel_cfg.height = 79; > - > - platform_add_devices(qhd_devices, ARRAY_SIZE(qhd_devices)); > - > -#else > - /* > - * For WVGA Panel (18-bit RGB, CONFIG_AP4EVB_WVGA=y) and > - * IRQ7 for Touch Panel, set dip switches S3, S43 to ON, OFF. > - */ > - gpio_request_one(189, GPIOF_OUT_INIT_HIGH, NULL); /* backlight */ > - gpio_request_one(151, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */ > - > - lcdc_info.clock_source = LCDC_CLK_BUS; > - lcdc_info.ch[0].interface_type = RGB18; > - lcdc_info.ch[0].clock_divider = 3; > - lcdc_info.ch[0].flags = 0; > - lcdc_info.ch[0].panel_cfg.width = 152; > - lcdc_info.ch[0].panel_cfg.height = 91; > - > - /* enable TouchScreen */ > - irq_set_irq_type(IRQ7, IRQ_TYPE_LEVEL_LOW); > - > - tsc_device.irq = IRQ7; > - i2c_register_board_info(0, &tsc_device, 1); > -#endif /* CONFIG_AP4EVB_QHD */ > - > - /* CEU */ > - > - /* > - * TODO: reserve memory for V4L2 DMA buffers, when a suitable API > - * becomes available > - */ > - > - /* MIPI-CSI stuff */ > - clk = clk_get(NULL, "vck1_clk"); > - if (!IS_ERR(clk)) { > - clk_set_rate(clk, clk_round_rate(clk, 13000000)); > - clk_enable(clk); > - clk_put(clk); > - } > - > - sh7372_add_standard_devices(); > - > - /* Reset HDMI, must be held at least one EXTALR (32768Hz) period */ > -#define SRCR4 IOMEM(0xe61580bc) > - srcr4 = __raw_readl(SRCR4); > - __raw_writel(srcr4 | (1 << 13), SRCR4); > - udelay(50); > - __raw_writel(srcr4 & ~(1 << 13), SRCR4); > - > - platform_add_devices(ap4evb_devices, ARRAY_SIZE(ap4evb_devices)); > - > - rmobile_add_devices_to_domains(domain_devices, > - ARRAY_SIZE(domain_devices)); > - > - hdmi_init_pm_clock(); > - sh7372_pm_init(); > - pm_clk_add(&fsi_device.dev, "spu2"); > - pm_clk_add(&lcdc1_device.dev, "hdmi"); > -} > - > -MACHINE_START(AP4EVB, "ap4evb") > - .map_io = sh7372_map_io, > - .init_early = sh7372_add_early_devices, > - .init_irq = sh7372_init_irq, > - .handle_irq = shmobile_handle_irq_intc, > - .init_machine = ap4evb_init, > - .init_late = sh7372_pm_init_late, > - .init_time = sh7372_earlytimer_init, > -MACHINE_END > diff --git a/arch/arm/mach-shmobile/include/mach/head-ap4evb.txt b/arch/arm/mach-shmobile/include/mach/head-ap4evb.txt > deleted file mode 100644 > index 9f134df..0000000 > --- a/arch/arm/mach-shmobile/include/mach/head-ap4evb.txt > +++ /dev/null > @@ -1,93 +0,0 @@ > -LIST "partner-jet-setup.txt" > -LIST "(C) Copyright 2010 Renesas Solutions Corp" > -LIST "Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>" > - > -LIST "RWT Setting" > -EW 0xE6020004, 0xA500 > -EW 0xE6030004, 0xA500 > - > -LIST "GPIO Setting" > -EB 0xE6051013, 0xA2 > - > -LIST "CPG" > -ED 0xE61500C0, 0x00000002 > - > -WAIT 1, 0xFE40009C > - > -LIST "FRQCR" > -ED 0xE6150000, 0x2D1305C3 > -ED 0xE61500E0, 0x9E40358E > -ED 0xE6150004, 0x80331050 > - > -WAIT 1, 0xFE40009C > - > -ED 0xE61500E4, 0x00002000 > - > -WAIT 1, 0xFE40009C > - > -LIST "PLL" > -ED 0xE6150028, 0x00004000 > - > -WAIT 1, 0xFE40009C > - > -ED 0xE615002C, 0x93000040 > - > -WAIT 1, 0xFE40009C > - > -LIST "SUB/USBClk" > -ED 0xE6150080, 0x00000180 > - > -LIST "BSC" > -ED 0xFEC10000, 0x00E0001B > - > -LIST "SBSC1" > -ED 0xFE400354, 0x01AD8000 > -ED 0xFE400354, 0x01AD8001 > - > -WAIT 5, 0xFE40009C > - > -ED 0xFE400008, 0xBCC90151 > -ED 0xFE400040, 0x41774113 > -ED 0xFE400044, 0x2712E229 > -ED 0xFE400048, 0x20C18505 > -ED 0xFE40004C, 0x00110209 > -ED 0xFE400010, 0x00000087 > - > -WAIT 30, 0xFE40009C > - > -ED 0xFE400084, 0x0000003F > -EB 0xFE500000, 0x00 > - > -WAIT 5, 0xFE40009C > - > -ED 0xFE400084, 0x0000FF0A > -EB 0xFE500000, 0x00 > - > -WAIT 1, 0xFE40009C > - > -ED 0xFE400084, 0x00002201 > -EB 0xFE500000, 0x00 > -ED 0xFE400084, 0x00000302 > -EB 0xFE500000, 0x00 > -EB 0xFE5C0000, 0x00 > -ED 0xFE400008, 0xBCC90159 > -ED 0xFE40008C, 0x88800004 > -ED 0xFE400094, 0x00000004 > -ED 0xFE400028, 0xA55A0032 > -ED 0xFE40002C, 0xA55A000C > -ED 0xFE400020, 0xA55A2048 > -ED 0xFE400008, 0xBCC90959 > - > -LIST "Change CPGA setting" > -ED 0xE61500E0, 0x9E40352E > -ED 0xE6150004, 0x80331050 > - > -WAIT 1, 0xFE40009C > - > -ED 0xFE400354, 0x01AD8002 > - > -LIST "SCIF0 - Serial port for earlyprintk" > -EB 0xE6053098, 0xe1 > -EW 0xE6C40000, 0x0000 > -EB 0xE6C40004, 0x19 > -EW 0xE6C40008, 0x0030 > diff --git a/arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h b/arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h > deleted file mode 100644 > index db59fdb..0000000 > --- a/arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h > +++ /dev/null > @@ -1,29 +0,0 @@ > -#ifndef MMC_AP4EB_H > -#define MMC_AP4EB_H > - > -#define PORT185CR (void __iomem *)0xe60520b9 > -#define PORT186CR (void __iomem *)0xe60520ba > -#define PORT187CR (void __iomem *)0xe60520bb > -#define PORT188CR (void __iomem *)0xe60520bc > - > -#define PORTR191_160DR (void __iomem *)0xe6056014 > - > -static inline void mmc_init_progress(void) > -{ > - /* Initialise LEDS1-4 > - * registers: PORT185CR-PORT188CR (LED1-LED4 Control) > - * value: 0x10 - enable output > - */ > - __raw_writeb(0x10, PORT185CR); > - __raw_writeb(0x10, PORT186CR); > - __raw_writeb(0x10, PORT187CR); > - __raw_writeb(0x10, PORT188CR); > -} > - > -static inline void mmc_update_progress(int n) > -{ > - __raw_writel((__raw_readl(PORTR191_160DR) & ~(0xf << 25)) | > - (1 << (25 + n)), PORTR191_160DR); > -} > - > -#endif /* MMC_AP4EB_H */ > diff --git a/arch/arm/mach-shmobile/include/mach/mmc.h b/arch/arm/mach-shmobile/include/mach/mmc.h > index 21a59db..e979b8f 100644 > --- a/arch/arm/mach-shmobile/include/mach/mmc.h > +++ b/arch/arm/mach-shmobile/include/mach/mmc.h > @@ -7,9 +7,7 @@ > * > **************************************************/ > > -#ifdef CONFIG_MACH_AP4EVB > -#include "mach/mmc-ap4eb.h" > -#elif defined(CONFIG_MACH_MACKEREL) > +#ifdef CONFIG_MACH_MACKEREL > #include "mach/mmc-mackerel.h" > #else > #error "unsupported board." > diff --git a/arch/arm/mach-shmobile/include/mach/zboot.h b/arch/arm/mach-shmobile/include/mach/zboot.h > index 308b5cf..f2d8744 100644 > --- a/arch/arm/mach-shmobile/include/mach/zboot.h > +++ b/arch/arm/mach-shmobile/include/mach/zboot.h > @@ -10,11 +10,7 @@ > * > **************************************************/ > > -#ifdef CONFIG_MACH_AP4EVB > -#define MACH_TYPE MACH_TYPE_AP4EVB > -#define MEMORY_START 0x40000000 > -#include "mach/head-ap4evb.txt" > -#elif defined(CONFIG_MACH_MACKEREL) > +#ifdef CONFIG_MACH_MACKEREL > #define MACH_TYPE MACH_TYPE_MACKEREL > #define MEMORY_START 0x40000000 > #include "mach/head-mackerel.txt" > -- > 1.8.2.1 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-sh" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > --- Guennadi Liakhovetski, Ph.D. Freelance Open-Source Software Developer http://www.open-technology.de/
On Thu, Jun 13, 2013 at 09:36:51PM +0200, Guennadi Liakhovetski wrote: > Hi Simon > > On Thu, 13 Jun 2013, Simon Horman wrote: > > > From: Magnus Damm <damm@opensource.se> > > > > Remove board support for the sh7372 based AP4EVB board > > > > The sh7372 SoC support code is still kept around since it > > is in use by the Mackerel board which is basically a more > > recent board where the design is based on AP4EVB. > > > > Signed-off-by: Magnus Damm <damm@opensource.se> > > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > It would be a pity if this patch gets pulled now. We're still discussing > with Magnus, I believe. My opinion is, that this board is a good testing > platform for V4L2. It is the only board in the mainline, using the CSI2 > interface, present on multiple Renesas SoCs, including r8a73a4 (APE6), and > (probably, not 100% sure) sh73a0 (AG5), and the IMX074 camera sensor, not > present on any other platform. If this board is removed, supporting both > CSI2 and IMX074 will become difficult. Besides, AP4EVB is used as an > example in my V4L2 clock / async probing patch series: > > http://www.mail-archive.com/linux-media@vger.kernel.org/msg63174.html > > If still possible, would be good to delay removing this board until we > complete our discussion. Does the board still work with the rest of this series applied? > > Thanks > Guennadi > > > --- > > arch/arm/configs/ap4evb_defconfig | 56 - > > arch/arm/mach-shmobile/Kconfig | 21 - > > arch/arm/mach-shmobile/Makefile | 1 - > > arch/arm/mach-shmobile/Makefile.boot | 1 - > > arch/arm/mach-shmobile/board-ap4evb.c | 1310 -------------------- > > .../arm/mach-shmobile/include/mach/head-ap4evb.txt | 93 -- > > arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h | 29 - > > arch/arm/mach-shmobile/include/mach/mmc.h | 4 +- > > arch/arm/mach-shmobile/include/mach/zboot.h | 6 +- > > 9 files changed, 2 insertions(+), 1519 deletions(-) > > delete mode 100644 arch/arm/configs/ap4evb_defconfig > > delete mode 100644 arch/arm/mach-shmobile/board-ap4evb.c > > delete mode 100644 arch/arm/mach-shmobile/include/mach/head-ap4evb.txt > > delete mode 100644 arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h > > > > diff --git a/arch/arm/configs/ap4evb_defconfig b/arch/arm/configs/ap4evb_defconfig > > deleted file mode 100644 > > index 66894f7..0000000 > > --- a/arch/arm/configs/ap4evb_defconfig > > +++ /dev/null > > @@ -1,56 +0,0 @@ > > -CONFIG_EXPERIMENTAL=y > > -CONFIG_SYSVIPC=y > > -CONFIG_IKCONFIG=y > > -CONFIG_IKCONFIG_PROC=y > > -CONFIG_LOG_BUF_SHIFT=16 > > -CONFIG_BLK_DEV_INITRD=y > > -CONFIG_SLAB=y > > -# CONFIG_BLK_DEV_BSG is not set > > -# CONFIG_IOSCHED_DEADLINE is not set > > -# CONFIG_IOSCHED_CFQ is not set > > -CONFIG_ARCH_SHMOBILE=y > > -CONFIG_ARCH_SH7372=y > > -CONFIG_MACH_AP4EVB=y > > -CONFIG_AEABI=y > > -# CONFIG_OABI_COMPAT is not set > > -CONFIG_ZBOOT_ROM_TEXT=0x0 > > -CONFIG_ZBOOT_ROM_BSS=0x0 > > -CONFIG_CMDLINE="console=ttySC0,115200 earlyprintk=sh-sci.0,115200" > > -CONFIG_KEXEC=y > > -CONFIG_PM=y > > -# CONFIG_SUSPEND is not set > > -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" > > -# CONFIG_FIRMWARE_IN_KERNEL is not set > > -CONFIG_MTD=y > > -CONFIG_MTD_CONCAT=y > > -CONFIG_MTD_PARTITIONS=y > > -CONFIG_MTD_CHAR=y > > -CONFIG_MTD_BLOCK=y > > -CONFIG_MTD_CFI=y > > -CONFIG_MTD_CFI_INTELEXT=y > > -CONFIG_MTD_PHYSMAP=y > > -CONFIG_MTD_NAND=y > > -# CONFIG_BLK_DEV is not set > > -# CONFIG_MISC_DEVICES is not set > > -# CONFIG_INPUT_MOUSEDEV_PSAUX is not set > > -# CONFIG_INPUT_KEYBOARD is not set > > -# CONFIG_INPUT_MOUSE is not set > > -# CONFIG_SERIO is not set > > -CONFIG_SERIAL_SH_SCI=y > > -CONFIG_SERIAL_SH_SCI_NR_UARTS=8 > > -CONFIG_SERIAL_SH_SCI_CONSOLE=y > > -# CONFIG_LEGACY_PTYS is not set > > -# CONFIG_HW_RANDOM is not set > > -# CONFIG_HWMON is not set > > -# CONFIG_VGA_CONSOLE is not set > > -# CONFIG_HID_SUPPORT is not set > > -# CONFIG_USB_SUPPORT is not set > > -# CONFIG_DNOTIFY is not set > > -CONFIG_TMPFS=y > > -# CONFIG_MISC_FILESYSTEMS is not set > > -CONFIG_MAGIC_SYSRQ=y > > -CONFIG_DEBUG_KERNEL=y > > -# CONFIG_DETECT_SOFTLOCKUP is not set > > -# CONFIG_RCU_CPU_STALL_DETECTOR is not set > > -# CONFIG_FTRACE is not set > > -# CONFIG_CRC32 is not set > > diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig > > index 747f68a..ae1a530 100644 > > --- a/arch/arm/mach-shmobile/Kconfig > > +++ b/arch/arm/mach-shmobile/Kconfig > > @@ -69,27 +69,6 @@ config ARCH_EMEV2 > > > > comment "SH-Mobile Board Type" > > > > -config MACH_AP4EVB > > - bool "AP4EVB board" > > - depends on ARCH_SH7372 > > - select ARCH_REQUIRE_GPIOLIB > > - select REGULATOR_FIXED_VOLTAGE if REGULATOR > > - select SH_LCD_MIPI_DSI > > - select SND_SOC_AK4642 if SND_SIMPLE_CARD > > - > > -choice > > - prompt "AP4EVB LCD panel selection" > > - default AP4EVB_QHD > > - depends on MACH_AP4EVB > > - > > -config AP4EVB_QHD > > - bool "MIPI-DSI QHD (960x540)" > > - > > -config AP4EVB_WVGA > > - bool "Parallel WVGA (800x480)" > > - > > -endchoice > > - > > config MACH_AG5EVM > > bool "AG5EVM board" > > depends on ARCH_SH73A0 > > diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile > > index 068f1da..aae28f3 100644 > > --- a/arch/arm/mach-shmobile/Makefile > > +++ b/arch/arm/mach-shmobile/Makefile > > @@ -35,7 +35,6 @@ obj-$(CONFIG_ARCH_R8A7779) += pm-r8a7779.o > > obj-$(CONFIG_ARCH_SH73A0) += pm-sh73a0.o > > > > # Board objects > > -obj-$(CONFIG_MACH_AP4EVB) += board-ap4evb.o > > obj-$(CONFIG_MACH_AG5EVM) += board-ag5evm.o > > obj-$(CONFIG_MACH_APE6EVM) += board-ape6evm.o > > obj-$(CONFIG_MACH_MACKEREL) += board-mackerel.o > > diff --git a/arch/arm/mach-shmobile/Makefile.boot b/arch/arm/mach-shmobile/Makefile.boot > > index 6b147ea..3030673 100644 > > --- a/arch/arm/mach-shmobile/Makefile.boot > > +++ b/arch/arm/mach-shmobile/Makefile.boot > > @@ -1,7 +1,6 @@ > > # per-board load address for uImage > > loadaddr-y := > > loadaddr-$(CONFIG_MACH_AG5EVM) += 0x40008000 > > -loadaddr-$(CONFIG_MACH_AP4EVB) += 0x40008000 > > loadaddr-$(CONFIG_MACH_APE6EVM) += 0x40008000 > > loadaddr-$(CONFIG_MACH_ARMADILLO800EVA) += 0x40008000 > > loadaddr-$(CONFIG_MACH_ARMADILLO800EVA_REFERENCE) += 0x40008000 > > diff --git a/arch/arm/mach-shmobile/board-ap4evb.c b/arch/arm/mach-shmobile/board-ap4evb.c > > deleted file mode 100644 > > index 297bf5e..0000000 > > --- a/arch/arm/mach-shmobile/board-ap4evb.c > > +++ /dev/null > > @@ -1,1310 +0,0 @@ > > -/* > > - * AP4EVB board support > > - * > > - * Copyright (C) 2010 Magnus Damm > > - * Copyright (C) 2008 Yoshihiro Shimoda > > - * > > - * This program is free software; you can redistribute it and/or modify > > - * it under the terms of the GNU General Public License as published by > > - * the Free Software Foundation; version 2 of the License. > > - * > > - * This program is distributed in the hope that it will be useful, > > - * but WITHOUT ANY WARRANTY; without even the implied warranty of > > - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > - * GNU General Public License for more details. > > - * > > - * You should have received a copy of the GNU General Public License > > - * along with this program; if not, write to the Free Software > > - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA > > - */ > > -#include <linux/clk.h> > > -#include <linux/kernel.h> > > -#include <linux/init.h> > > -#include <linux/interrupt.h> > > -#include <linux/irq.h> > > -#include <linux/platform_device.h> > > -#include <linux/delay.h> > > -#include <linux/mfd/tmio.h> > > -#include <linux/mmc/host.h> > > -#include <linux/mmc/sh_mobile_sdhi.h> > > -#include <linux/mtd/mtd.h> > > -#include <linux/mtd/partitions.h> > > -#include <linux/mtd/physmap.h> > > -#include <linux/mmc/sh_mmcif.h> > > -#include <linux/i2c.h> > > -#include <linux/i2c/tsc2007.h> > > -#include <linux/io.h> > > -#include <linux/pinctrl/machine.h> > > -#include <linux/regulator/fixed.h> > > -#include <linux/regulator/machine.h> > > -#include <linux/smsc911x.h> > > -#include <linux/sh_intc.h> > > -#include <linux/sh_clk.h> > > -#include <linux/gpio.h> > > -#include <linux/input.h> > > -#include <linux/leds.h> > > -#include <linux/input/sh_keysc.h> > > -#include <linux/usb/r8a66597.h> > > -#include <linux/pm_clock.h> > > -#include <linux/dma-mapping.h> > > - > > -#include <media/sh_mobile_ceu.h> > > -#include <media/sh_mobile_csi2.h> > > -#include <media/soc_camera.h> > > - > > -#include <sound/sh_fsi.h> > > -#include <sound/simple_card.h> > > - > > -#include <video/sh_mobile_hdmi.h> > > -#include <video/sh_mobile_lcdc.h> > > -#include <video/sh_mipi_dsi.h> > > - > > -#include <mach/common.h> > > -#include <mach/irqs.h> > > -#include <mach/sh7372.h> > > - > > -#include <asm/mach-types.h> > > -#include <asm/mach/arch.h> > > -#include <asm/setup.h> > > - > > -#include "sh-gpio.h" > > - > > -/* > > - * Address Interface BusWidth note > > - * ------------------------------------------------------------------ > > - * 0x0000_0000 NOR Flash ROM (MCP) 16bit SW7 : bit1 = ON > > - * 0x0800_0000 user area - > > - * 0x1000_0000 NOR Flash ROM (MCP) 16bit SW7 : bit1 = OFF > > - * 0x1400_0000 Ether (LAN9220) 16bit > > - * 0x1600_0000 user area - cannot use with NAND > > - * 0x1800_0000 user area - > > - * 0x1A00_0000 - > > - * 0x4000_0000 LPDDR2-SDRAM (POP) 32bit > > - */ > > - > > -/* > > - * NOR Flash ROM > > - * > > - * SW1 | SW2 | SW7 | NOR Flash ROM > > - * bit1 | bit1 bit2 | bit1 | Memory allocation > > - * ------+------------+------+------------------ > > - * OFF | ON OFF | ON | Area 0 > > - * OFF | ON OFF | OFF | Area 4 > > - */ > > - > > -/* > > - * NAND Flash ROM > > - * > > - * SW1 | SW2 | SW7 | NAND Flash ROM > > - * bit1 | bit1 bit2 | bit2 | Memory allocation > > - * ------+------------+------+------------------ > > - * OFF | ON OFF | ON | FCE 0 > > - * OFF | ON OFF | OFF | FCE 1 > > - */ > > - > > -/* > > - * SMSC 9220 > > - * > > - * SW1 SMSC 9220 > > - * ----------------------- > > - * ON access disable > > - * OFF access enable > > - */ > > - > > -/* > > - * LCD / IRQ / KEYSC / IrDA > > - * > > - * IRQ = IRQ26 (TS), IRQ27 (VIO), IRQ28 (QHD-TouchScreen) > > - * LCD = 2nd LCDC (WVGA) > > - * > > - * | SW43 | > > - * SW3 | ON | OFF | > > - * -------------+-----------------------+---------------+ > > - * ON | KEY / IrDA | LCD | > > - * OFF | KEY / IrDA / IRQ | IRQ | > > - * > > - * > > - * QHD / WVGA display > > - * > > - * You can choice display type on menuconfig. > > - * Then, check above dip-switch. > > - */ > > - > > -/* > > - * USB > > - * > > - * J7 : 1-2 MAX3355E VBUS > > - * 2-3 DC 5.0V > > - * > > - * S39: bit2: off > > - */ > > - > > -/* > > - * FSI/FSMI > > - * > > - * SW41 : ON : SH-Mobile AP4 Audio Mode > > - * : OFF : Bluetooth Audio Mode > > - * > > - * it needs amixer settings for playing > > - * > > - * amixer set "Headphone Enable" on > > - */ > > - > > -/* > > - * MMC0/SDHI1 (CN7) > > - * > > - * J22 : select card voltage > > - * 1-2 pin : 1.8v > > - * 2-3 pin : 3.3v > > - * > > - * SW1 | SW33 > > - * | bit1 | bit2 | bit3 | bit4 > > - * ------------+------+------+------+------- > > - * MMC0 OFF | OFF | ON | ON | X > > - * SDHI1 OFF | ON | X | OFF | ON > > - * > > - * voltage lebel > > - * CN7 : 1.8v > > - * CN12: 3.3v > > - */ > > - > > -/* Dummy supplies, where voltage doesn't matter */ > > -static struct regulator_consumer_supply fixed1v8_power_consumers[] = > > -{ > > - /* J22 default position: 1.8V */ > > - REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"), > > - REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"), > > - REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"), > > - REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"), > > -}; > > - > > -static struct regulator_consumer_supply fixed3v3_power_consumers[] = > > -{ > > - REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"), > > - REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"), > > -}; > > - > > -static struct regulator_consumer_supply dummy_supplies[] = { > > - REGULATOR_SUPPLY("vddvario", "smsc911x"), > > - REGULATOR_SUPPLY("vdd33a", "smsc911x"), > > -}; > > - > > -/* MTD */ > > -static struct mtd_partition nor_flash_partitions[] = { > > - { > > - .name = "loader", > > - .offset = 0x00000000, > > - .size = 512 * 1024, > > - .mask_flags = MTD_WRITEABLE, > > - }, > > - { > > - .name = "bootenv", > > - .offset = MTDPART_OFS_APPEND, > > - .size = 512 * 1024, > > - .mask_flags = MTD_WRITEABLE, > > - }, > > - { > > - .name = "kernel_ro", > > - .offset = MTDPART_OFS_APPEND, > > - .size = 8 * 1024 * 1024, > > - .mask_flags = MTD_WRITEABLE, > > - }, > > - { > > - .name = "kernel", > > - .offset = MTDPART_OFS_APPEND, > > - .size = 8 * 1024 * 1024, > > - }, > > - { > > - .name = "data", > > - .offset = MTDPART_OFS_APPEND, > > - .size = MTDPART_SIZ_FULL, > > - }, > > -}; > > - > > -static struct physmap_flash_data nor_flash_data = { > > - .width = 2, > > - .parts = nor_flash_partitions, > > - .nr_parts = ARRAY_SIZE(nor_flash_partitions), > > -}; > > - > > -static struct resource nor_flash_resources[] = { > > - [0] = { > > - .start = 0x20000000, /* CS0 shadow instead of regular CS0 */ > > - .end = 0x28000000 - 1, /* needed by USB MASK ROM boot */ > > - .flags = IORESOURCE_MEM, > > - } > > -}; > > - > > -static struct platform_device nor_flash_device = { > > - .name = "physmap-flash", > > - .dev = { > > - .platform_data = &nor_flash_data, > > - }, > > - .num_resources = ARRAY_SIZE(nor_flash_resources), > > - .resource = nor_flash_resources, > > -}; > > - > > -/* SMSC 9220 */ > > -static struct resource smc911x_resources[] = { > > - { > > - .start = 0x14000000, > > - .end = 0x16000000 - 1, > > - .flags = IORESOURCE_MEM, > > - }, { > > - .start = evt2irq(0x02c0) /* IRQ6A */, > > - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, > > - }, > > -}; > > - > > -static struct smsc911x_platform_config smsc911x_info = { > > - .flags = SMSC911X_USE_16BIT | SMSC911X_SAVE_MAC_ADDRESS, > > - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, > > - .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL, > > -}; > > - > > -static struct platform_device smc911x_device = { > > - .name = "smsc911x", > > - .id = -1, > > - .num_resources = ARRAY_SIZE(smc911x_resources), > > - .resource = smc911x_resources, > > - .dev = { > > - .platform_data = &smsc911x_info, > > - }, > > -}; > > - > > -/* > > - * The card detect pin of the top SD/MMC slot (CN7) is active low and is > > - * connected to GPIO A22 of SH7372 (GPIO 41). > > - */ > > -static int slot_cn7_get_cd(struct platform_device *pdev) > > -{ > > - return !gpio_get_value(41); > > -} > > -/* MERAM */ > > -static struct sh_mobile_meram_info meram_info = { > > - .addr_mode = SH_MOBILE_MERAM_MODE1, > > -}; > > - > > -static struct resource meram_resources[] = { > > - [0] = { > > - .name = "regs", > > - .start = 0xe8000000, > > - .end = 0xe807ffff, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .name = "meram", > > - .start = 0xe8080000, > > - .end = 0xe81fffff, > > - .flags = IORESOURCE_MEM, > > - }, > > -}; > > - > > -static struct platform_device meram_device = { > > - .name = "sh_mobile_meram", > > - .id = 0, > > - .num_resources = ARRAY_SIZE(meram_resources), > > - .resource = meram_resources, > > - .dev = { > > - .platform_data = &meram_info, > > - }, > > -}; > > - > > -/* SH_MMCIF */ > > -static struct resource sh_mmcif_resources[] = { > > - [0] = { > > - .name = "MMCIF", > > - .start = 0xE6BD0000, > > - .end = 0xE6BD00FF, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - /* MMC ERR */ > > - .start = evt2irq(0x1ac0), > > - .flags = IORESOURCE_IRQ, > > - }, > > - [2] = { > > - /* MMC NOR */ > > - .start = evt2irq(0x1ae0), > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct sh_mmcif_plat_data sh_mmcif_plat = { > > - .sup_pclk = 0, > > - .ocr = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34, > > - .caps = MMC_CAP_4_BIT_DATA | > > - MMC_CAP_8_BIT_DATA | > > - MMC_CAP_NEEDS_POLL, > > - .get_cd = slot_cn7_get_cd, > > - .slave_id_tx = SHDMA_SLAVE_MMCIF_TX, > > - .slave_id_rx = SHDMA_SLAVE_MMCIF_RX, > > -}; > > - > > -static struct platform_device sh_mmcif_device = { > > - .name = "sh_mmcif", > > - .id = 0, > > - .dev = { > > - .dma_mask = NULL, > > - .coherent_dma_mask = 0xffffffff, > > - .platform_data = &sh_mmcif_plat, > > - }, > > - .num_resources = ARRAY_SIZE(sh_mmcif_resources), > > - .resource = sh_mmcif_resources, > > -}; > > - > > -/* SDHI0 */ > > -static struct sh_mobile_sdhi_info sdhi0_info = { > > - .dma_slave_tx = SHDMA_SLAVE_SDHI0_TX, > > - .dma_slave_rx = SHDMA_SLAVE_SDHI0_RX, > > - .tmio_caps = MMC_CAP_SDIO_IRQ, > > -}; > > - > > -static struct resource sdhi0_resources[] = { > > - [0] = { > > - .name = "SDHI0", > > - .start = 0xe6850000, > > - .end = 0xe68500ff, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = evt2irq(0x0e00) /* SDHI0_SDHI0I0 */, > > - .flags = IORESOURCE_IRQ, > > - }, > > - [2] = { > > - .start = evt2irq(0x0e20) /* SDHI0_SDHI0I1 */, > > - .flags = IORESOURCE_IRQ, > > - }, > > - [3] = { > > - .start = evt2irq(0x0e40) /* SDHI0_SDHI0I2 */, > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct platform_device sdhi0_device = { > > - .name = "sh_mobile_sdhi", > > - .num_resources = ARRAY_SIZE(sdhi0_resources), > > - .resource = sdhi0_resources, > > - .id = 0, > > - .dev = { > > - .platform_data = &sdhi0_info, > > - }, > > -}; > > - > > -/* SDHI1 */ > > -static struct sh_mobile_sdhi_info sdhi1_info = { > > - .dma_slave_tx = SHDMA_SLAVE_SDHI1_TX, > > - .dma_slave_rx = SHDMA_SLAVE_SDHI1_RX, > > - .tmio_ocr_mask = MMC_VDD_165_195, > > - .tmio_flags = TMIO_MMC_WRPROTECT_DISABLE, > > - .tmio_caps = MMC_CAP_NEEDS_POLL | MMC_CAP_SDIO_IRQ, > > - .get_cd = slot_cn7_get_cd, > > -}; > > - > > -static struct resource sdhi1_resources[] = { > > - [0] = { > > - .name = "SDHI1", > > - .start = 0xe6860000, > > - .end = 0xe68600ff, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = evt2irq(0x0e80), /* SDHI1_SDHI1I0 */ > > - .flags = IORESOURCE_IRQ, > > - }, > > - [2] = { > > - .start = evt2irq(0x0ea0), /* SDHI1_SDHI1I1 */ > > - .flags = IORESOURCE_IRQ, > > - }, > > - [3] = { > > - .start = evt2irq(0x0ec0), /* SDHI1_SDHI1I2 */ > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct platform_device sdhi1_device = { > > - .name = "sh_mobile_sdhi", > > - .num_resources = ARRAY_SIZE(sdhi1_resources), > > - .resource = sdhi1_resources, > > - .id = 1, > > - .dev = { > > - .platform_data = &sdhi1_info, > > - }, > > -}; > > - > > -/* USB1 */ > > -static void usb1_host_port_power(int port, int power) > > -{ > > - if (!power) /* only power-on supported for now */ > > - return; > > - > > - /* set VBOUT/PWEN and EXTLP1 in DVSTCTR */ > > - __raw_writew(__raw_readw(IOMEM(0xE68B0008)) | 0x600, IOMEM(0xE68B0008)); > > -} > > - > > -static struct r8a66597_platdata usb1_host_data = { > > - .on_chip = 1, > > - .port_power = usb1_host_port_power, > > -}; > > - > > -static struct resource usb1_host_resources[] = { > > - [0] = { > > - .name = "USBHS", > > - .start = 0xE68B0000, > > - .end = 0xE68B00E6 - 1, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = evt2irq(0x1ce0) /* USB1_USB1I0 */, > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct platform_device usb1_host_device = { > > - .name = "r8a66597_hcd", > > - .id = 1, > > - .dev = { > > - .dma_mask = NULL, /* not use dma */ > > - .coherent_dma_mask = 0xffffffff, > > - .platform_data = &usb1_host_data, > > - }, > > - .num_resources = ARRAY_SIZE(usb1_host_resources), > > - .resource = usb1_host_resources, > > -}; > > - > > -/* > > - * QHD display > > - */ > > -#ifdef CONFIG_AP4EVB_QHD > > - > > -/* KEYSC (Needs SW43 set to ON) */ > > -static struct sh_keysc_info keysc_info = { > > - .mode = SH_KEYSC_MODE_1, > > - .scan_timing = 3, > > - .delay = 2500, > > - .keycodes = { > > - KEY_0, KEY_1, KEY_2, KEY_3, KEY_4, > > - KEY_5, KEY_6, KEY_7, KEY_8, KEY_9, > > - KEY_A, KEY_B, KEY_C, KEY_D, KEY_E, > > - KEY_F, KEY_G, KEY_H, KEY_I, KEY_J, > > - KEY_K, KEY_L, KEY_M, KEY_N, KEY_O, > > - }, > > -}; > > - > > -static struct resource keysc_resources[] = { > > - [0] = { > > - .name = "KEYSC", > > - .start = 0xe61b0000, > > - .end = 0xe61b0063, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = evt2irq(0x0be0), /* KEYSC_KEY */ > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct platform_device keysc_device = { > > - .name = "sh_keysc", > > - .id = 0, /* "keysc0" clock */ > > - .num_resources = ARRAY_SIZE(keysc_resources), > > - .resource = keysc_resources, > > - .dev = { > > - .platform_data = &keysc_info, > > - }, > > -}; > > - > > -/* MIPI-DSI */ > > -static int sh_mipi_set_dot_clock(struct platform_device *pdev, > > - void __iomem *base, > > - int enable) > > -{ > > - struct clk *pck = clk_get(&pdev->dev, "dsip_clk"); > > - > > - if (IS_ERR(pck)) > > - return PTR_ERR(pck); > > - > > - if (enable) { > > - /* > > - * DSIPCLK = 24MHz > > - * D-PHY = DSIPCLK * ((0x6*2)+1) = 312MHz (see .phyctrl) > > - * HsByteCLK = D-PHY/8 = 39MHz > > - * > > - * X * Y * FPS = > > - * (544+72+600+16) * (961+8+8+2) * 30 = 36.1MHz > > - */ > > - clk_set_rate(pck, clk_round_rate(pck, 24000000)); > > - clk_enable(pck); > > - } else { > > - clk_disable(pck); > > - } > > - > > - clk_put(pck); > > - > > - return 0; > > -} > > - > > -static struct resource mipidsi0_resources[] = { > > - [0] = { > > - .start = 0xffc60000, > > - .end = 0xffc63073, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = 0xffc68000, > > - .end = 0xffc680ef, > > - .flags = IORESOURCE_MEM, > > - }, > > -}; > > - > > -static struct sh_mipi_dsi_info mipidsi0_info = { > > - .data_format = MIPI_RGB888, > > - .channel = LCDC_CHAN_MAINLCD, > > - .lane = 2, > > - .vsynw_offset = 17, > > - .phyctrl = 0x6 << 8, > > - .flags = SH_MIPI_DSI_SYNC_PULSES_MODE | > > - SH_MIPI_DSI_HSbyteCLK, > > - .set_dot_clock = sh_mipi_set_dot_clock, > > -}; > > - > > -static struct platform_device mipidsi0_device = { > > - .name = "sh-mipi-dsi", > > - .num_resources = ARRAY_SIZE(mipidsi0_resources), > > - .resource = mipidsi0_resources, > > - .id = 0, > > - .dev = { > > - .platform_data = &mipidsi0_info, > > - }, > > -}; > > - > > -static struct platform_device *qhd_devices[] __initdata = { > > - &mipidsi0_device, > > - &keysc_device, > > -}; > > -#endif /* CONFIG_AP4EVB_QHD */ > > - > > -/* LCDC0 */ > > -static const struct fb_videomode ap4evb_lcdc_modes[] = { > > - { > > -#ifdef CONFIG_AP4EVB_QHD > > - .name = "R63302(QHD)", > > - .xres = 544, > > - .yres = 961, > > - .left_margin = 72, > > - .right_margin = 600, > > - .hsync_len = 16, > > - .upper_margin = 8, > > - .lower_margin = 8, > > - .vsync_len = 2, > > - .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT, > > -#else > > - .name = "WVGA Panel", > > - .xres = 800, > > - .yres = 480, > > - .left_margin = 220, > > - .right_margin = 110, > > - .hsync_len = 70, > > - .upper_margin = 20, > > - .lower_margin = 5, > > - .vsync_len = 5, > > - .sync = 0, > > -#endif > > - }, > > -}; > > - > > -static const struct sh_mobile_meram_cfg lcd_meram_cfg = { > > - .icb[0] = { > > - .meram_size = 0x40, > > - }, > > - .icb[1] = { > > - .meram_size = 0x40, > > - }, > > -}; > > - > > -static struct sh_mobile_lcdc_info lcdc_info = { > > - .meram_dev = &meram_info, > > - .ch[0] = { > > - .chan = LCDC_CHAN_MAINLCD, > > - .fourcc = V4L2_PIX_FMT_RGB565, > > - .lcd_modes = ap4evb_lcdc_modes, > > - .num_modes = ARRAY_SIZE(ap4evb_lcdc_modes), > > - .meram_cfg = &lcd_meram_cfg, > > -#ifdef CONFIG_AP4EVB_QHD > > - .tx_dev = &mipidsi0_device, > > -#endif > > - } > > -}; > > - > > -static struct resource lcdc_resources[] = { > > - [0] = { > > - .name = "LCDC", > > - .start = 0xfe940000, /* P4-only space */ > > - .end = 0xfe943fff, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = intcs_evt2irq(0x580), > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct platform_device lcdc_device = { > > - .name = "sh_mobile_lcdc_fb", > > - .num_resources = ARRAY_SIZE(lcdc_resources), > > - .resource = lcdc_resources, > > - .dev = { > > - .platform_data = &lcdc_info, > > - .coherent_dma_mask = ~0, > > - }, > > -}; > > - > > -/* FSI */ > > -#define IRQ_FSI evt2irq(0x1840) > > -static struct sh_fsi_platform_info fsi_info = { > > - .port_b = { > > - .flags = SH_FSI_CLK_CPG | > > - SH_FSI_FMT_SPDIF, > > - }, > > -}; > > - > > -static struct resource fsi_resources[] = { > > - [0] = { > > - .name = "FSI", > > - .start = 0xFE3C0000, > > - .end = 0xFE3C0400 - 1, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = IRQ_FSI, > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct platform_device fsi_device = { > > - .name = "sh_fsi2", > > - .id = -1, > > - .num_resources = ARRAY_SIZE(fsi_resources), > > - .resource = fsi_resources, > > - .dev = { > > - .platform_data = &fsi_info, > > - }, > > -}; > > - > > -static struct asoc_simple_card_info fsi2_ak4643_info = { > > - .name = "AK4643", > > - .card = "FSI2A-AK4643", > > - .codec = "ak4642-codec.0-0013", > > - .platform = "sh_fsi2", > > - .daifmt = SND_SOC_DAIFMT_LEFT_J, > > - .cpu_dai = { > > - .name = "fsia-dai", > > - .fmt = SND_SOC_DAIFMT_CBS_CFS, > > - }, > > - .codec_dai = { > > - .name = "ak4642-hifi", > > - .fmt = SND_SOC_DAIFMT_CBM_CFM, > > - .sysclk = 11289600, > > - }, > > -}; > > - > > -static struct platform_device fsi_ak4643_device = { > > - .name = "asoc-simple-card", > > - .dev = { > > - .platform_data = &fsi2_ak4643_info, > > - }, > > -}; > > - > > -/* LCDC1 */ > > -static long ap4evb_clk_optimize(unsigned long target, unsigned long *best_freq, > > - unsigned long *parent_freq); > > - > > -static struct sh_mobile_hdmi_info hdmi_info = { > > - .flags = HDMI_SND_SRC_SPDIF, > > - .clk_optimize_parent = ap4evb_clk_optimize, > > -}; > > - > > -static struct resource hdmi_resources[] = { > > - [0] = { > > - .name = "HDMI", > > - .start = 0xe6be0000, > > - .end = 0xe6be00ff, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - /* There's also an HDMI interrupt on INTCS @ 0x18e0 */ > > - .start = evt2irq(0x17e0), > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct platform_device hdmi_device = { > > - .name = "sh-mobile-hdmi", > > - .num_resources = ARRAY_SIZE(hdmi_resources), > > - .resource = hdmi_resources, > > - .id = -1, > > - .dev = { > > - .platform_data = &hdmi_info, > > - }, > > -}; > > - > > -static long ap4evb_clk_optimize(unsigned long target, unsigned long *best_freq, > > - unsigned long *parent_freq) > > -{ > > - struct clk *hdmi_ick = clk_get(&hdmi_device.dev, "ick"); > > - long error; > > - > > - if (IS_ERR(hdmi_ick)) { > > - int ret = PTR_ERR(hdmi_ick); > > - pr_err("Cannot get HDMI ICK: %d\n", ret); > > - return ret; > > - } > > - > > - error = clk_round_parent(hdmi_ick, target, best_freq, parent_freq, 1, 64); > > - > > - clk_put(hdmi_ick); > > - > > - return error; > > -} > > - > > -static const struct sh_mobile_meram_cfg hdmi_meram_cfg = { > > - .icb[0] = { > > - .meram_size = 0x100, > > - }, > > - .icb[1] = { > > - .meram_size = 0x100, > > - }, > > -}; > > - > > -static struct sh_mobile_lcdc_info sh_mobile_lcdc1_info = { > > - .clock_source = LCDC_CLK_EXTERNAL, > > - .meram_dev = &meram_info, > > - .ch[0] = { > > - .chan = LCDC_CHAN_MAINLCD, > > - .fourcc = V4L2_PIX_FMT_RGB565, > > - .interface_type = RGB24, > > - .clock_divider = 1, > > - .flags = LCDC_FLAGS_DWPOL, > > - .meram_cfg = &hdmi_meram_cfg, > > - .tx_dev = &hdmi_device, > > - } > > -}; > > - > > -static struct resource lcdc1_resources[] = { > > - [0] = { > > - .name = "LCDC1", > > - .start = 0xfe944000, > > - .end = 0xfe947fff, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = intcs_evt2irq(0x1780), > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct platform_device lcdc1_device = { > > - .name = "sh_mobile_lcdc_fb", > > - .num_resources = ARRAY_SIZE(lcdc1_resources), > > - .resource = lcdc1_resources, > > - .id = 1, > > - .dev = { > > - .platform_data = &sh_mobile_lcdc1_info, > > - .coherent_dma_mask = ~0, > > - }, > > -}; > > - > > -static struct asoc_simple_card_info fsi2_hdmi_info = { > > - .name = "HDMI", > > - .card = "FSI2B-HDMI", > > - .codec = "sh-mobile-hdmi", > > - .platform = "sh_fsi2", > > - .cpu_dai = { > > - .name = "fsib-dai", > > - .fmt = SND_SOC_DAIFMT_CBM_CFM | SND_SOC_DAIFMT_IB_NF, > > - }, > > - .codec_dai = { > > - .name = "sh_mobile_hdmi-hifi", > > - }, > > -}; > > - > > -static struct platform_device fsi_hdmi_device = { > > - .name = "asoc-simple-card", > > - .id = 1, > > - .dev = { > > - .platform_data = &fsi2_hdmi_info, > > - }, > > -}; > > - > > -static struct gpio_led ap4evb_leds[] = { > > - { > > - .name = "led4", > > - .gpio = 185, > > - .default_state = LEDS_GPIO_DEFSTATE_ON, > > - }, > > - { > > - .name = "led2", > > - .gpio = 186, > > - .default_state = LEDS_GPIO_DEFSTATE_ON, > > - }, > > - { > > - .name = "led3", > > - .gpio = 187, > > - .default_state = LEDS_GPIO_DEFSTATE_ON, > > - }, > > - { > > - .name = "led1", > > - .gpio = 188, > > - .default_state = LEDS_GPIO_DEFSTATE_ON, > > - } > > -}; > > - > > -static struct gpio_led_platform_data ap4evb_leds_pdata = { > > - .num_leds = ARRAY_SIZE(ap4evb_leds), > > - .leds = ap4evb_leds, > > -}; > > - > > -static struct platform_device leds_device = { > > - .name = "leds-gpio", > > - .id = 0, > > - .dev = { > > - .platform_data = &ap4evb_leds_pdata, > > - }, > > -}; > > - > > -static struct i2c_board_info imx074_info = { > > - I2C_BOARD_INFO("imx074", 0x1a), > > -}; > > - > > -static struct soc_camera_link imx074_link = { > > - .bus_id = 0, > > - .board_info = &imx074_info, > > - .i2c_adapter_id = 0, > > - .module_name = "imx074", > > -}; > > - > > -static struct platform_device ap4evb_camera = { > > - .name = "soc-camera-pdrv", > > - .id = 0, > > - .dev = { > > - .platform_data = &imx074_link, > > - }, > > -}; > > - > > -static struct sh_csi2_client_config csi2_clients[] = { > > - { > > - .phy = SH_CSI2_PHY_MAIN, > > - .lanes = 0, /* default: 2 lanes */ > > - .channel = 0, > > - .pdev = &ap4evb_camera, > > - }, > > -}; > > - > > -static struct sh_csi2_pdata csi2_info = { > > - .type = SH_CSI2C, > > - .clients = csi2_clients, > > - .num_clients = ARRAY_SIZE(csi2_clients), > > - .flags = SH_CSI2_ECC | SH_CSI2_CRC, > > -}; > > - > > -static struct resource csi2_resources[] = { > > - [0] = { > > - .name = "CSI2", > > - .start = 0xffc90000, > > - .end = 0xffc90fff, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = intcs_evt2irq(0x17a0), > > - .flags = IORESOURCE_IRQ, > > - }, > > -}; > > - > > -static struct sh_mobile_ceu_companion csi2 = { > > - .id = 0, > > - .num_resources = ARRAY_SIZE(csi2_resources), > > - .resource = csi2_resources, > > - .platform_data = &csi2_info, > > -}; > > - > > -static struct sh_mobile_ceu_info sh_mobile_ceu_info = { > > - .flags = SH_CEU_FLAG_USE_8BIT_BUS, > > - .max_width = 8188, > > - .max_height = 8188, > > - .csi2 = &csi2, > > -}; > > - > > -static struct resource ceu_resources[] = { > > - [0] = { > > - .name = "CEU", > > - .start = 0xfe910000, > > - .end = 0xfe91009f, > > - .flags = IORESOURCE_MEM, > > - }, > > - [1] = { > > - .start = intcs_evt2irq(0x880), > > - .flags = IORESOURCE_IRQ, > > - }, > > - [2] = { > > - /* place holder for contiguous memory */ > > - }, > > -}; > > - > > -static struct platform_device ceu_device = { > > - .name = "sh_mobile_ceu", > > - .id = 0, /* "ceu0" clock */ > > - .num_resources = ARRAY_SIZE(ceu_resources), > > - .resource = ceu_resources, > > - .dev = { > > - .platform_data = &sh_mobile_ceu_info, > > - .coherent_dma_mask = 0xffffffff, > > - }, > > -}; > > - > > -static struct platform_device *ap4evb_devices[] __initdata = { > > - &leds_device, > > - &nor_flash_device, > > - &smc911x_device, > > - &sdhi0_device, > > - &sdhi1_device, > > - &usb1_host_device, > > - &fsi_device, > > - &fsi_ak4643_device, > > - &fsi_hdmi_device, > > - &sh_mmcif_device, > > - &hdmi_device, > > - &lcdc_device, > > - &lcdc1_device, > > - &ceu_device, > > - &ap4evb_camera, > > - &meram_device, > > -}; > > - > > -static void __init hdmi_init_pm_clock(void) > > -{ > > - struct clk *hdmi_ick = clk_get(&hdmi_device.dev, "ick"); > > - int ret; > > - long rate; > > - > > - if (IS_ERR(hdmi_ick)) { > > - ret = PTR_ERR(hdmi_ick); > > - pr_err("Cannot get HDMI ICK: %d\n", ret); > > - goto out; > > - } > > - > > - ret = clk_set_parent(&sh7372_pllc2_clk, &sh7372_dv_clki_div2_clk); > > - if (ret < 0) { > > - pr_err("Cannot set PLLC2 parent: %d, %d users\n", ret, sh7372_pllc2_clk.usecount); > > - goto out; > > - } > > - > > - pr_debug("PLLC2 initial frequency %lu\n", clk_get_rate(&sh7372_pllc2_clk)); > > - > > - rate = clk_round_rate(&sh7372_pllc2_clk, 594000000); > > - if (rate < 0) { > > - pr_err("Cannot get suitable rate: %ld\n", rate); > > - ret = rate; > > - goto out; > > - } > > - > > - ret = clk_set_rate(&sh7372_pllc2_clk, rate); > > - if (ret < 0) { > > - pr_err("Cannot set rate %ld: %d\n", rate, ret); > > - goto out; > > - } > > - > > - pr_debug("PLLC2 set frequency %lu\n", rate); > > - > > - ret = clk_set_parent(hdmi_ick, &sh7372_pllc2_clk); > > - if (ret < 0) > > - pr_err("Cannot set HDMI parent: %d\n", ret); > > - > > -out: > > - if (!IS_ERR(hdmi_ick)) > > - clk_put(hdmi_ick); > > -} > > - > > -/* TouchScreen */ > > -#ifdef CONFIG_AP4EVB_QHD > > -# define GPIO_TSC_PORT 123 > > -#else /* WVGA */ > > -# define GPIO_TSC_PORT 40 > > -#endif > > - > > -#define IRQ28 evt2irq(0x3380) /* IRQ28A */ > > -#define IRQ7 evt2irq(0x02e0) /* IRQ7A */ > > -static int ts_get_pendown_state(void) > > -{ > > - return !gpio_get_value(GPIO_TSC_PORT); > > -} > > - > > -static int ts_init(void) > > -{ > > - gpio_request_one(GPIO_TSC_PORT, GPIOF_IN, NULL); > > - > > - return 0; > > -} > > - > > -static struct tsc2007_platform_data tsc2007_info = { > > - .model = 2007, > > - .x_plate_ohms = 180, > > - .get_pendown_state = ts_get_pendown_state, > > - .init_platform_hw = ts_init, > > -}; > > - > > -static struct i2c_board_info tsc_device = { > > - I2C_BOARD_INFO("tsc2007", 0x48), > > - .type = "tsc2007", > > - .platform_data = &tsc2007_info, > > - /*.irq is selected on ap4evb_init */ > > -}; > > - > > -/* I2C */ > > -static struct i2c_board_info i2c0_devices[] = { > > - { > > - I2C_BOARD_INFO("ak4643", 0x13), > > - }, > > -}; > > - > > -static struct i2c_board_info i2c1_devices[] = { > > - { > > - I2C_BOARD_INFO("r2025sd", 0x32), > > - }, > > -}; > > - > > - > > -static const struct pinctrl_map ap4evb_pinctrl_map[] = { > > - /* CEU */ > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-sh7372", > > - "ceu_clk_0", "ceu"), > > - /* FSIA (AK4643) */ > > - PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-sh7372", > > - "fsia_sclk_in", "fsia"), > > - PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-sh7372", > > - "fsia_data_in", "fsia"), > > - PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-sh7372", > > - "fsia_data_out", "fsia"), > > - /* FSIB (HDMI) */ > > - PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.1", "pfc-sh7372", > > - "fsib_mclk_in", "fsib"), > > - /* HDMI */ > > - PIN_MAP_MUX_GROUP_DEFAULT("sh-mobile-hdmi", "pfc-sh7372", > > - "hdmi", "hdmi"), > > - /* KEYSC */ > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_keysc", "pfc-sh7372", > > - "keysc_in04_0", "keysc"), > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_keysc", "pfc-sh7372", > > - "keysc_out5", "keysc"), > > -#ifndef CONFIG_AP4EVB_QHD > > - /* LCDC */ > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh7372", > > - "lcd_data18", "lcd"), > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-sh7372", > > - "lcd_sync", "lcd"), > > -#endif > > - /* MMCIF */ > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh7372", > > - "mmc0_data8_0", "mmc0"), > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-sh7372", > > - "mmc0_ctrl_0", "mmc0"), > > - /* SCIFA0 */ > > - PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.0", "pfc-sh7372", > > - "scifa0_data", "scifa0"), > > - /* SDHI0 */ > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372", > > - "sdhi0_data4", "sdhi0"), > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372", > > - "sdhi0_ctrl", "sdhi0"), > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372", > > - "sdhi0_cd", "sdhi0"), > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-sh7372", > > - "sdhi0_wp", "sdhi0"), > > - /* SDHI1 */ > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-sh7372", > > - "sdhi1_data4", "sdhi1"), > > - PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.1", "pfc-sh7372", > > - "sdhi1_ctrl", "sdhi1"), > > - /* SMSC911X */ > > - PIN_MAP_MUX_GROUP_DEFAULT("smsc911x", "pfc-sh7372", > > - "bsc_cs5a", "bsc"), > > - PIN_MAP_MUX_GROUP_DEFAULT("smsc911x", "pfc-sh7372", > > - "intc_irq6_0", "intc"), > > - /* TSC2007 */ > > -#ifdef CONFIG_AP4EVB_QHD > > - PIN_MAP_MUX_GROUP_DEFAULT("1-0048", "pfc-sh7372", > > - "intc_irq28_0", "intc"), > > -#else /* WVGA */ > > - PIN_MAP_MUX_GROUP_DEFAULT("1-0048", "pfc-sh7372", > > - "intc_irq7_0", "intc"), > > -#endif > > - /* USBHS1 */ > > - PIN_MAP_MUX_GROUP_DEFAULT("r8a66597_hcd.1", "pfc-sh7372", > > - "usb1_vbus", "usb1"), > > - PIN_MAP_MUX_GROUP_DEFAULT("r8a66597_hcd.1", "pfc-sh7372", > > - "usb1_otg_id_0", "usb1"), > > - PIN_MAP_MUX_GROUP_DEFAULT("r8a66597_hcd.1", "pfc-sh7372", > > - "usb1_otg_ctrl_0", "usb1"), > > -}; > > - > > -#define GPIO_PORT9CR IOMEM(0xE6051009) > > -#define GPIO_PORT10CR IOMEM(0xE605100A) > > -#define USCCR1 IOMEM(0xE6058144) > > -static void __init ap4evb_init(void) > > -{ > > - struct pm_domain_device domain_devices[] = { > > - { "A4LC", &lcdc1_device, }, > > - { "A4LC", &lcdc_device, }, > > - { "A4MP", &fsi_device, }, > > - { "A3SP", &sh_mmcif_device, }, > > - { "A3SP", &sdhi0_device, }, > > - { "A3SP", &sdhi1_device, }, > > - { "A4R", &ceu_device, }, > > - }; > > - u32 srcr4; > > - struct clk *clk; > > - > > - regulator_register_always_on(0, "fixed-1.8V", fixed1v8_power_consumers, > > - ARRAY_SIZE(fixed1v8_power_consumers), 1800000); > > - regulator_register_always_on(1, "fixed-3.3V", fixed3v3_power_consumers, > > - ARRAY_SIZE(fixed3v3_power_consumers), 3300000); > > - regulator_register_fixed(2, dummy_supplies, ARRAY_SIZE(dummy_supplies)); > > - > > - /* External clock source */ > > - clk_set_rate(&sh7372_dv_clki_clk, 27000000); > > - > > - pinctrl_register_mappings(ap4evb_pinctrl_map, > > - ARRAY_SIZE(ap4evb_pinctrl_map)); > > - sh7372_pinmux_init(); > > - > > - /* enable Debug switch (S6) */ > > - gpio_request_one(32, GPIOF_IN | GPIOF_EXPORT, NULL); > > - gpio_request_one(33, GPIOF_IN | GPIOF_EXPORT, NULL); > > - gpio_request_one(34, GPIOF_IN | GPIOF_EXPORT, NULL); > > - gpio_request_one(35, GPIOF_IN | GPIOF_EXPORT, NULL); > > - > > - /* setup USB phy */ > > - __raw_writew(0x8a0a, IOMEM(0xE6058130)); /* USBCR4 */ > > - > > - /* FSI2 port A (ak4643) */ > > - gpio_request_one(161, GPIOF_OUT_INIT_LOW, NULL); /* slave */ > > - > > - gpio_request(9, NULL); > > - gpio_request(10, NULL); > > - gpio_direction_none(GPIO_PORT9CR); /* FSIAOBT needs no direction */ > > - gpio_direction_none(GPIO_PORT10CR); /* FSIAOLR needs no direction */ > > - > > - /* card detect pin for MMC slot (CN7) */ > > - gpio_request_one(41, GPIOF_IN, NULL); > > - > > - /* FSI2 port B (HDMI) */ > > - __raw_writew(__raw_readw(USCCR1) & ~(1 << 6), USCCR1); /* use SPDIF */ > > - > > - /* set SPU2 clock to 119.6 MHz */ > > - clk = clk_get(NULL, "spu_clk"); > > - if (!IS_ERR(clk)) { > > - clk_set_rate(clk, clk_round_rate(clk, 119600000)); > > - clk_put(clk); > > - } > > - > > - /* > > - * set irq priority, to avoid sound chopping > > - * when NFS rootfs is used > > - * FSI(3) > SMSC911X(2) > > - */ > > - intc_set_priority(IRQ_FSI, 3); > > - > > - i2c_register_board_info(0, i2c0_devices, > > - ARRAY_SIZE(i2c0_devices)); > > - > > - i2c_register_board_info(1, i2c1_devices, > > - ARRAY_SIZE(i2c1_devices)); > > - > > -#ifdef CONFIG_AP4EVB_QHD > > - > > - /* > > - * For QHD Panel (MIPI-DSI, CONFIG_AP4EVB_QHD=y) and > > - * IRQ28 for Touch Panel, set dip switches S3, S43 as OFF, ON. > > - */ > > - > > - /* enable TouchScreen */ > > - irq_set_irq_type(IRQ28, IRQ_TYPE_LEVEL_LOW); > > - > > - tsc_device.irq = IRQ28; > > - i2c_register_board_info(1, &tsc_device, 1); > > - > > - /* LCDC0 */ > > - lcdc_info.clock_source = LCDC_CLK_PERIPHERAL; > > - lcdc_info.ch[0].interface_type = RGB24; > > - lcdc_info.ch[0].clock_divider = 1; > > - lcdc_info.ch[0].flags = LCDC_FLAGS_DWPOL; > > - lcdc_info.ch[0].panel_cfg.width = 44; > > - lcdc_info.ch[0].panel_cfg.height = 79; > > - > > - platform_add_devices(qhd_devices, ARRAY_SIZE(qhd_devices)); > > - > > -#else > > - /* > > - * For WVGA Panel (18-bit RGB, CONFIG_AP4EVB_WVGA=y) and > > - * IRQ7 for Touch Panel, set dip switches S3, S43 to ON, OFF. > > - */ > > - gpio_request_one(189, GPIOF_OUT_INIT_HIGH, NULL); /* backlight */ > > - gpio_request_one(151, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */ > > - > > - lcdc_info.clock_source = LCDC_CLK_BUS; > > - lcdc_info.ch[0].interface_type = RGB18; > > - lcdc_info.ch[0].clock_divider = 3; > > - lcdc_info.ch[0].flags = 0; > > - lcdc_info.ch[0].panel_cfg.width = 152; > > - lcdc_info.ch[0].panel_cfg.height = 91; > > - > > - /* enable TouchScreen */ > > - irq_set_irq_type(IRQ7, IRQ_TYPE_LEVEL_LOW); > > - > > - tsc_device.irq = IRQ7; > > - i2c_register_board_info(0, &tsc_device, 1); > > -#endif /* CONFIG_AP4EVB_QHD */ > > - > > - /* CEU */ > > - > > - /* > > - * TODO: reserve memory for V4L2 DMA buffers, when a suitable API > > - * becomes available > > - */ > > - > > - /* MIPI-CSI stuff */ > > - clk = clk_get(NULL, "vck1_clk"); > > - if (!IS_ERR(clk)) { > > - clk_set_rate(clk, clk_round_rate(clk, 13000000)); > > - clk_enable(clk); > > - clk_put(clk); > > - } > > - > > - sh7372_add_standard_devices(); > > - > > - /* Reset HDMI, must be held at least one EXTALR (32768Hz) period */ > > -#define SRCR4 IOMEM(0xe61580bc) > > - srcr4 = __raw_readl(SRCR4); > > - __raw_writel(srcr4 | (1 << 13), SRCR4); > > - udelay(50); > > - __raw_writel(srcr4 & ~(1 << 13), SRCR4); > > - > > - platform_add_devices(ap4evb_devices, ARRAY_SIZE(ap4evb_devices)); > > - > > - rmobile_add_devices_to_domains(domain_devices, > > - ARRAY_SIZE(domain_devices)); > > - > > - hdmi_init_pm_clock(); > > - sh7372_pm_init(); > > - pm_clk_add(&fsi_device.dev, "spu2"); > > - pm_clk_add(&lcdc1_device.dev, "hdmi"); > > -} > > - > > -MACHINE_START(AP4EVB, "ap4evb") > > - .map_io = sh7372_map_io, > > - .init_early = sh7372_add_early_devices, > > - .init_irq = sh7372_init_irq, > > - .handle_irq = shmobile_handle_irq_intc, > > - .init_machine = ap4evb_init, > > - .init_late = sh7372_pm_init_late, > > - .init_time = sh7372_earlytimer_init, > > -MACHINE_END > > diff --git a/arch/arm/mach-shmobile/include/mach/head-ap4evb.txt b/arch/arm/mach-shmobile/include/mach/head-ap4evb.txt > > deleted file mode 100644 > > index 9f134df..0000000 > > --- a/arch/arm/mach-shmobile/include/mach/head-ap4evb.txt > > +++ /dev/null > > @@ -1,93 +0,0 @@ > > -LIST "partner-jet-setup.txt" > > -LIST "(C) Copyright 2010 Renesas Solutions Corp" > > -LIST "Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>" > > - > > -LIST "RWT Setting" > > -EW 0xE6020004, 0xA500 > > -EW 0xE6030004, 0xA500 > > - > > -LIST "GPIO Setting" > > -EB 0xE6051013, 0xA2 > > - > > -LIST "CPG" > > -ED 0xE61500C0, 0x00000002 > > - > > -WAIT 1, 0xFE40009C > > - > > -LIST "FRQCR" > > -ED 0xE6150000, 0x2D1305C3 > > -ED 0xE61500E0, 0x9E40358E > > -ED 0xE6150004, 0x80331050 > > - > > -WAIT 1, 0xFE40009C > > - > > -ED 0xE61500E4, 0x00002000 > > - > > -WAIT 1, 0xFE40009C > > - > > -LIST "PLL" > > -ED 0xE6150028, 0x00004000 > > - > > -WAIT 1, 0xFE40009C > > - > > -ED 0xE615002C, 0x93000040 > > - > > -WAIT 1, 0xFE40009C > > - > > -LIST "SUB/USBClk" > > -ED 0xE6150080, 0x00000180 > > - > > -LIST "BSC" > > -ED 0xFEC10000, 0x00E0001B > > - > > -LIST "SBSC1" > > -ED 0xFE400354, 0x01AD8000 > > -ED 0xFE400354, 0x01AD8001 > > - > > -WAIT 5, 0xFE40009C > > - > > -ED 0xFE400008, 0xBCC90151 > > -ED 0xFE400040, 0x41774113 > > -ED 0xFE400044, 0x2712E229 > > -ED 0xFE400048, 0x20C18505 > > -ED 0xFE40004C, 0x00110209 > > -ED 0xFE400010, 0x00000087 > > - > > -WAIT 30, 0xFE40009C > > - > > -ED 0xFE400084, 0x0000003F > > -EB 0xFE500000, 0x00 > > - > > -WAIT 5, 0xFE40009C > > - > > -ED 0xFE400084, 0x0000FF0A > > -EB 0xFE500000, 0x00 > > - > > -WAIT 1, 0xFE40009C > > - > > -ED 0xFE400084, 0x00002201 > > -EB 0xFE500000, 0x00 > > -ED 0xFE400084, 0x00000302 > > -EB 0xFE500000, 0x00 > > -EB 0xFE5C0000, 0x00 > > -ED 0xFE400008, 0xBCC90159 > > -ED 0xFE40008C, 0x88800004 > > -ED 0xFE400094, 0x00000004 > > -ED 0xFE400028, 0xA55A0032 > > -ED 0xFE40002C, 0xA55A000C > > -ED 0xFE400020, 0xA55A2048 > > -ED 0xFE400008, 0xBCC90959 > > - > > -LIST "Change CPGA setting" > > -ED 0xE61500E0, 0x9E40352E > > -ED 0xE6150004, 0x80331050 > > - > > -WAIT 1, 0xFE40009C > > - > > -ED 0xFE400354, 0x01AD8002 > > - > > -LIST "SCIF0 - Serial port for earlyprintk" > > -EB 0xE6053098, 0xe1 > > -EW 0xE6C40000, 0x0000 > > -EB 0xE6C40004, 0x19 > > -EW 0xE6C40008, 0x0030 > > diff --git a/arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h b/arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h > > deleted file mode 100644 > > index db59fdb..0000000 > > --- a/arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h > > +++ /dev/null > > @@ -1,29 +0,0 @@ > > -#ifndef MMC_AP4EB_H > > -#define MMC_AP4EB_H > > - > > -#define PORT185CR (void __iomem *)0xe60520b9 > > -#define PORT186CR (void __iomem *)0xe60520ba > > -#define PORT187CR (void __iomem *)0xe60520bb > > -#define PORT188CR (void __iomem *)0xe60520bc > > - > > -#define PORTR191_160DR (void __iomem *)0xe6056014 > > - > > -static inline void mmc_init_progress(void) > > -{ > > - /* Initialise LEDS1-4 > > - * registers: PORT185CR-PORT188CR (LED1-LED4 Control) > > - * value: 0x10 - enable output > > - */ > > - __raw_writeb(0x10, PORT185CR); > > - __raw_writeb(0x10, PORT186CR); > > - __raw_writeb(0x10, PORT187CR); > > - __raw_writeb(0x10, PORT188CR); > > -} > > - > > -static inline void mmc_update_progress(int n) > > -{ > > - __raw_writel((__raw_readl(PORTR191_160DR) & ~(0xf << 25)) | > > - (1 << (25 + n)), PORTR191_160DR); > > -} > > - > > -#endif /* MMC_AP4EB_H */ > > diff --git a/arch/arm/mach-shmobile/include/mach/mmc.h b/arch/arm/mach-shmobile/include/mach/mmc.h > > index 21a59db..e979b8f 100644 > > --- a/arch/arm/mach-shmobile/include/mach/mmc.h > > +++ b/arch/arm/mach-shmobile/include/mach/mmc.h > > @@ -7,9 +7,7 @@ > > * > > **************************************************/ > > > > -#ifdef CONFIG_MACH_AP4EVB > > -#include "mach/mmc-ap4eb.h" > > -#elif defined(CONFIG_MACH_MACKEREL) > > +#ifdef CONFIG_MACH_MACKEREL > > #include "mach/mmc-mackerel.h" > > #else > > #error "unsupported board." > > diff --git a/arch/arm/mach-shmobile/include/mach/zboot.h b/arch/arm/mach-shmobile/include/mach/zboot.h > > index 308b5cf..f2d8744 100644 > > --- a/arch/arm/mach-shmobile/include/mach/zboot.h > > +++ b/arch/arm/mach-shmobile/include/mach/zboot.h > > @@ -10,11 +10,7 @@ > > * > > **************************************************/ > > > > -#ifdef CONFIG_MACH_AP4EVB > > -#define MACH_TYPE MACH_TYPE_AP4EVB > > -#define MEMORY_START 0x40000000 > > -#include "mach/head-ap4evb.txt" > > -#elif defined(CONFIG_MACH_MACKEREL) > > +#ifdef CONFIG_MACH_MACKEREL > > #define MACH_TYPE MACH_TYPE_MACKEREL > > #define MEMORY_START 0x40000000 > > #include "mach/head-mackerel.txt" > > -- > > 1.8.2.1 > > > > -- > > To unsubscribe from this list: send the line "unsubscribe linux-sh" in > > the body of a message to majordomo@vger.kernel.org > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > > > --- > Guennadi Liakhovetski, Ph.D. > Freelance Open-Source Software Developer > http://www.open-technology.de/ >
On Thu, Jun 13, 2013 at 03:59:38PM +0900, Simon Horman wrote: > Hi Olof, Hi Arnd, > > This pull request is based on renesas-pinmux-for-v3.11, which you have > already pulled, in order to provide pre-requisites. > > The following changes since commit 5fcf4a3c3a5bc08bf72a50ef1332501a3c1b96bb: > > ARM: shmobile: marzen: Use RCAR_GP_PIN macro (2013-06-05 17:18:24 +0900) > > are available in the git repository at: > > git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-cleanup-boot-for-v3.11 > > for you to fetch changes up to 9da629661d207299ad119a6735eb2411f54fd45f: > > ARM: shmobile: Remove Bonito board support (2013-06-13 14:26:04 +0900) Sorry about this but it seems that there is still some discussion, which I was not previously aware of, about the patch to remove the AP4EVB board. Please ignore this pull-request for now. > > ---------------------------------------------------------------- > Renesas ARM based SoC boot cleanup for v3.11 > > Work by Magnus Damm and others to clean up the boot of and move > things closer to supporting MULTIARCH. > > As a side effect of this work it was decided to remove support for > two boards, Bonito and APE4EVM. Those patches are included in this > series as they depend on earlier patches in the series. > > ---------------------------------------------------------------- > Kuninori Morimoto (1): > ARM: shmobile: Remove Bonito board support > > Magnus Damm (14): > ARM: shmobile: uImage load address rework > ARM: shmobile: Let romImage rely on default ATAGS > ARM: shmobile: Remove romImage CONFIG_MEMORY_START > ARM: shmobile: Rework sh7372 sleep code to use virt_to_phys() > ARM: shmobile: Add SMP boot function and argument > ARM: shmobile: Add SCU boot function using argument > ARM: shmobile: r8a7779 SMP with SCU boot fn and args > ARM: shmobile: sh73a0 SMP with SCU boot fn and args > ARM: shmobile: EMEV2 SMP with SCU boot fn and args > ARM: shmobile: Remove old SCU boot code > ARM: shmobile: Enable ARM_PATCH_PHYS_VIRT > ARM: shmobile: Remove MEMORY_START/SIZE > ARM: shmobile: Remove mach/memory.h > ARM: shmobile: Remove AP4EVB board support > > arch/arm/Kconfig | 2 +- > arch/arm/boot/compressed/head-shmobile.S | 21 +- > arch/arm/configs/ap4evb_defconfig | 56 - > arch/arm/configs/bonito_defconfig | 72 -- > arch/arm/mach-shmobile/Kconfig | 58 - > arch/arm/mach-shmobile/Makefile | 2 - > arch/arm/mach-shmobile/Makefile.boot | 18 +- > arch/arm/mach-shmobile/board-ap4evb.c | 1310 -------------------- > arch/arm/mach-shmobile/board-bonito.c | 502 -------- > arch/arm/mach-shmobile/headsmp-scu.S | 29 +- > arch/arm/mach-shmobile/headsmp.S | 13 +- > arch/arm/mach-shmobile/include/mach/common.h | 6 +- > .../arm/mach-shmobile/include/mach/head-ap4evb.txt | 93 -- > arch/arm/mach-shmobile/include/mach/memory.h | 7 - > arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h | 29 - > arch/arm/mach-shmobile/include/mach/mmc.h | 4 +- > arch/arm/mach-shmobile/include/mach/sh7372.h | 2 + > arch/arm/mach-shmobile/include/mach/zboot.h | 6 +- > arch/arm/mach-shmobile/pm-sh7372.c | 3 + > arch/arm/mach-shmobile/sleep-sh7372.S | 5 +- > arch/arm/mach-shmobile/smp-emev2.c | 6 +- > arch/arm/mach-shmobile/smp-r8a7779.c | 6 +- > arch/arm/mach-shmobile/smp-sh73a0.c | 6 +- > 23 files changed, 68 insertions(+), 2188 deletions(-) > delete mode 100644 arch/arm/configs/ap4evb_defconfig > delete mode 100644 arch/arm/configs/bonito_defconfig > delete mode 100644 arch/arm/mach-shmobile/board-ap4evb.c > delete mode 100644 arch/arm/mach-shmobile/board-bonito.c > delete mode 100644 arch/arm/mach-shmobile/include/mach/head-ap4evb.txt > delete mode 100644 arch/arm/mach-shmobile/include/mach/memory.h > delete mode 100644 arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h > -- > To unsubscribe from this list: send the line "unsubscribe linux-sh" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html >
On Fri, 14 Jun 2013, Simon Horman wrote: > On Thu, Jun 13, 2013 at 09:36:51PM +0200, Guennadi Liakhovetski wrote: > > Hi Simon > > > > On Thu, 13 Jun 2013, Simon Horman wrote: > > > > > From: Magnus Damm <damm@opensource.se> > > > > > > Remove board support for the sh7372 based AP4EVB board > > > > > > The sh7372 SoC support code is still kept around since it > > > is in use by the Mackerel board which is basically a more > > > recent board where the design is based on AP4EVB. > > > > > > Signed-off-by: Magnus Damm <damm@opensource.se> > > > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > > > It would be a pity if this patch gets pulled now. We're still discussing > > with Magnus, I believe. My opinion is, that this board is a good testing > > platform for V4L2. It is the only board in the mainline, using the CSI2 > > interface, present on multiple Renesas SoCs, including r8a73a4 (APE6), and > > (probably, not 100% sure) sh73a0 (AG5), and the IMX074 camera sensor, not > > present on any other platform. If this board is removed, supporting both > > CSI2 and IMX074 will become difficult. Besides, AP4EVB is used as an > > example in my V4L2 clock / async probing patch series: > > > > http://www.mail-archive.com/linux-media@vger.kernel.org/msg63174.html > > > > If still possible, would be good to delay removing this board until we > > complete our discussion. > > Does the board still work with the rest of this series applied? Yes, it does. Thanks Guennadi --- Guennadi Liakhovetski, Ph.D. Freelance Open-Source Software Developer http://www.open-technology.de/
Hi Guennadi, On Fri, Jun 14, 2013 at 4:36 AM, Guennadi Liakhovetski <g.liakhovetski@gmx.de> wrote: > Hi Simon > > On Thu, 13 Jun 2013, Simon Horman wrote: > >> From: Magnus Damm <damm@opensource.se> >> >> Remove board support for the sh7372 based AP4EVB board >> >> The sh7372 SoC support code is still kept around since it >> is in use by the Mackerel board which is basically a more >> recent board where the design is based on AP4EVB. >> >> Signed-off-by: Magnus Damm <damm@opensource.se> >> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > It would be a pity if this patch gets pulled now. We're still discussing > with Magnus, I believe. My opinion is, that this board is a good testing > platform for V4L2. It is the only board in the mainline, using the CSI2 > interface, present on multiple Renesas SoCs, including r8a73a4 (APE6), and > (probably, not 100% sure) sh73a0 (AG5), and the IMX074 camera sensor, not > present on any other platform. If this board is removed, supporting both > CSI2 and IMX074 will become difficult. Besides, AP4EVB is used as an > example in my V4L2 clock / async probing patch series: > > http://www.mail-archive.com/linux-media@vger.kernel.org/msg63174.html > > If still possible, would be good to delay removing this board until we > complete our discussion. If fine with keeping the board if someone can show me progress in the area of INTC DT support. Recently I have not seen anything. So if no one is developing DT support for this board then I can't really see how we will be able to support it in the future with ARM SoC requirements for DT and MULTIPLATFORM... Cheers, / magnus
On Fri, 14 Jun 2013, Magnus Damm wrote: > Hi Guennadi, > > On Fri, Jun 14, 2013 at 4:36 AM, Guennadi Liakhovetski > <g.liakhovetski@gmx.de> wrote: > > Hi Simon > > > > On Thu, 13 Jun 2013, Simon Horman wrote: > > > >> From: Magnus Damm <damm@opensource.se> > >> > >> Remove board support for the sh7372 based AP4EVB board > >> > >> The sh7372 SoC support code is still kept around since it > >> is in use by the Mackerel board which is basically a more > >> recent board where the design is based on AP4EVB. > >> > >> Signed-off-by: Magnus Damm <damm@opensource.se> > >> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > > > It would be a pity if this patch gets pulled now. We're still discussing > > with Magnus, I believe. My opinion is, that this board is a good testing > > platform for V4L2. It is the only board in the mainline, using the CSI2 > > interface, present on multiple Renesas SoCs, including r8a73a4 (APE6), and > > (probably, not 100% sure) sh73a0 (AG5), and the IMX074 camera sensor, not > > present on any other platform. If this board is removed, supporting both > > CSI2 and IMX074 will become difficult. Besides, AP4EVB is used as an > > example in my V4L2 clock / async probing patch series: > > > > http://www.mail-archive.com/linux-media@vger.kernel.org/msg63174.html > > > > If still possible, would be good to delay removing this board until we > > complete our discussion. > > If fine with keeping the board if someone can show me progress in the > area of INTC DT support. Recently I have not seen anything. > > So if no one is developing DT support for this board then I can't > really see how we will be able to support it in the future with ARM > SoC requirements for DT and MULTIPLATFORM... You seem to be keeping the other sh7372 board currently in the mainline - the mackerel, so, keeping this one as well at least as long as sh7372 is at all supported shouldn't come at an extra cost. As for INTC DT - I think, the original idea was to specify the complete INTC configuration in DT, which looked pretty horrifying. And it shouldn't be needed, since INTC config is per-SoC, not per-board. What if we keep INTC configuration in SoC files and use aux-data to supply platform data to DT device nodes? Would that be difficult to implement? Thanks Guennadi --- Guennadi Liakhovetski, Ph.D. Freelance Open-Source Software Developer http://www.open-technology.de/
On Friday 14 June 2013, Magnus Damm wrote: > > If still possible, would be good to delay removing this board until we > > complete our discussion. > > If fine with keeping the board if someone can show me progress in the > area of INTC DT support. Recently I have not seen anything. As mentioned the last time we discussed this, I'm fine with using the existing code and "legacy" irqdomain for the older INTC implementations, as long as all the new ones can use your new generic code. Arnd
Hi Guennadi, On Fri, Jun 14, 2013 at 6:27 PM, Guennadi Liakhovetski <g.liakhovetski@gmx.de> wrote: > On Fri, 14 Jun 2013, Magnus Damm wrote: > >> Hi Guennadi, >> >> On Fri, Jun 14, 2013 at 4:36 AM, Guennadi Liakhovetski >> <g.liakhovetski@gmx.de> wrote: >> > Hi Simon >> > >> > On Thu, 13 Jun 2013, Simon Horman wrote: >> > >> >> From: Magnus Damm <damm@opensource.se> >> >> >> >> Remove board support for the sh7372 based AP4EVB board >> >> >> >> The sh7372 SoC support code is still kept around since it >> >> is in use by the Mackerel board which is basically a more >> >> recent board where the design is based on AP4EVB. >> >> >> >> Signed-off-by: Magnus Damm <damm@opensource.se> >> >> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> >> > >> > It would be a pity if this patch gets pulled now. We're still discussing >> > with Magnus, I believe. My opinion is, that this board is a good testing >> > platform for V4L2. It is the only board in the mainline, using the CSI2 >> > interface, present on multiple Renesas SoCs, including r8a73a4 (APE6), and >> > (probably, not 100% sure) sh73a0 (AG5), and the IMX074 camera sensor, not >> > present on any other platform. If this board is removed, supporting both >> > CSI2 and IMX074 will become difficult. Besides, AP4EVB is used as an >> > example in my V4L2 clock / async probing patch series: >> > >> > http://www.mail-archive.com/linux-media@vger.kernel.org/msg63174.html >> > >> > If still possible, would be good to delay removing this board until we >> > complete our discussion. >> >> If fine with keeping the board if someone can show me progress in the >> area of INTC DT support. Recently I have not seen anything. >> >> So if no one is developing DT support for this board then I can't >> really see how we will be able to support it in the future with ARM >> SoC requirements for DT and MULTIPLATFORM... > > You seem to be keeping the other sh7372 board currently in the mainline - > the mackerel, so, keeping this one as well at least as long as sh7372 is > at all supported shouldn't come at an extra cost. My plan is to slowly getting rid of sh7372 bit by bit. This since the sh7372 SoC never made it into mass production and it's getting old. As for AP4EVB, it's the first sh7372 board that we ran Linux on. It was soon replaced by Mackerel. So sh7372 was something we worked on a couple of generations ago. The sh7372 SoC code has issues related to DT for INTC, but that aside, the AP4EVB board has board specific Kconfig bits and other stuff making it difficult to fit into a single kernel binary. So I'd rather say good bye to all this unless someone plans to fix it. > As for INTC DT - I > think, the original idea was to specify the complete INTC configuration in > DT, which looked pretty horrifying. No, that was not the original idea. The first steps included code to keep the tables in C. http://www.spinics.net/lists/linux-sh/msg10788.html > And it shouldn't be needed, since INTC > config is per-SoC, not per-board. What if we keep INTC configuration in > SoC files and use aux-data to supply platform data to DT device nodes? > Would that be difficult to implement? Apparently. I made a prototype ages ago. Since then several people have been requested to work on this, but unfortunately no useful output has come from any of all this. So Guennadi, if you want to keep this board then you have to step up and fix things. If not then there is no point in keeping it. Cheers, / magnus
Hi Guennadi, On Fri, Jun 14, 2013 at 4:42 PM, Guennadi Liakhovetski <g.liakhovetski@gmx.de> wrote: > On Fri, 14 Jun 2013, Simon Horman wrote: > >> On Thu, Jun 13, 2013 at 09:36:51PM +0200, Guennadi Liakhovetski wrote: >> > Hi Simon >> > >> > On Thu, 13 Jun 2013, Simon Horman wrote: >> > >> > > From: Magnus Damm <damm@opensource.se> >> > > >> > > Remove board support for the sh7372 based AP4EVB board >> > > >> > > The sh7372 SoC support code is still kept around since it >> > > is in use by the Mackerel board which is basically a more >> > > recent board where the design is based on AP4EVB. >> > > >> > > Signed-off-by: Magnus Damm <damm@opensource.se> >> > > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> >> > >> > It would be a pity if this patch gets pulled now. We're still discussing >> > with Magnus, I believe. My opinion is, that this board is a good testing >> > platform for V4L2. It is the only board in the mainline, using the CSI2 >> > interface, present on multiple Renesas SoCs, including r8a73a4 (APE6), and >> > (probably, not 100% sure) sh73a0 (AG5), and the IMX074 camera sensor, not >> > present on any other platform. If this board is removed, supporting both >> > CSI2 and IMX074 will become difficult. Besides, AP4EVB is used as an >> > example in my V4L2 clock / async probing patch series: >> > >> > http://www.mail-archive.com/linux-media@vger.kernel.org/msg63174.html >> > >> > If still possible, would be good to delay removing this board until we >> > complete our discussion. >> >> Does the board still work with the rest of this series applied? > > Yes, it does. Uhm, apparently ap4evb_defconfig is broken so I don' t think so. I cooked up the following fix against renesas-next-20130613: [PATCH] ARM: shmobile: sh7372 build fix for SUSPEND=n && CPU_IDLE=n In the future, can you make sure the board is working and we're migrating towards DT? If so we can keep the board. Thanks, / magnus
Hi Arnd, On Fri, Jun 14, 2013 at 11:29 PM, Arnd Bergmann <arnd@arndb.de> wrote: > On Friday 14 June 2013, Magnus Damm wrote: >> > If still possible, would be good to delay removing this board until we >> > complete our discussion. >> >> If fine with keeping the board if someone can show me progress in the >> area of INTC DT support. Recently I have not seen anything. > > As mentioned the last time we discussed this, I'm fine with using the > existing code and "legacy" irqdomain for the older INTC implementations, > as long as all the new ones can use your new generic code. Thanks for explaining once again. Do you have any issues with us reducing the number of supported boards and/or SoCs? / magnus
On Mon, 17 Jun 2013, Magnus Damm wrote: [snip] > So Guennadi, if you want to keep this board then you have to step up > and fix things. If not then there is no point in keeping it. Ok, after a private discussion we agreed to remove the board, which will also make the drivers for the Renesas sh-/r-mobile CSI2 interface and for the Sony IMX074 sensor untestable and susceptible to removal. Also multi-subdevice support in soc-camera now will lose its only use and can become broken. I will also drop CSI2 and AP4EVB patches from my V4L2 clock / async probing series. Thanks Guennadi --- Guennadi Liakhovetski, Ph.D. Freelance Open-Source Software Developer http://www.open-technology.de/
On Mon, Jun 17, 2013 at 3:12 PM, Guennadi Liakhovetski <g.liakhovetski@gmx.de> wrote: > On Mon, 17 Jun 2013, Magnus Damm wrote: > > [snip] > >> So Guennadi, if you want to keep this board then you have to step up >> and fix things. If not then there is no point in keeping it. > > Ok, after a private discussion we agreed to remove the board, which will > also make the drivers for the Renesas sh-/r-mobile CSI2 interface and for > the Sony IMX074 sensor untestable and susceptible to removal. Also > multi-subdevice support in soc-camera now will lose its only use and can > become broken. I will also drop CSI2 and AP4EVB patches from my V4L2 clock > / async probing series. Thanks for writing this summary. It matches my understanding. It is unfortunate, but it seems to me that the camera sensor has to be tested on another platform. Regarding the CSI2 interface, as we discussed, this IP still exists in newer SoCs so because of that I recommend you to try to request newer hardware for future testing. About multi-subdevice and your ongoing work with V4L2 clock / async probing, please select a more recent hardware platform. Thanks, / magnus
On Monday 17 June 2013, Magnus Damm wrote: > On Fri, Jun 14, 2013 at 11:29 PM, Arnd Bergmann <arnd@arndb.de> wrote: > > On Friday 14 June 2013, Magnus Damm wrote: > >> > If still possible, would be good to delay removing this board until we > >> > complete our discussion. > >> > >> If fine with keeping the board if someone can show me progress in the > >> area of INTC DT support. Recently I have not seen anything. > > > > As mentioned the last time we discussed this, I'm fine with using the > > existing code and "legacy" irqdomain for the older INTC implementations, > > as long as all the new ones can use your new generic code. > > Thanks for explaining once again. Do you have any issues with us > reducing the number of supported boards and/or SoCs? No, I'm sure you know who the users of the board files in upstream kernels are. If someone comes up with a good reason why one of the files is needed after all, we can always revert the removal at a later point. I'm definitely in favor of removing known unused code that gets in the way of progress and adding clean code as quickly as we can review it. Arnd
On Mon, Jun 17, 2013 at 10:20:53PM +0200, Arnd Bergmann wrote: > On Monday 17 June 2013, Magnus Damm wrote: > > On Fri, Jun 14, 2013 at 11:29 PM, Arnd Bergmann <arnd@arndb.de> wrote: > > > On Friday 14 June 2013, Magnus Damm wrote: > > >> > If still possible, would be good to delay removing this board until we > > >> > complete our discussion. > > >> > > >> If fine with keeping the board if someone can show me progress in the > > >> area of INTC DT support. Recently I have not seen anything. > > > > > > As mentioned the last time we discussed this, I'm fine with using the > > > existing code and "legacy" irqdomain for the older INTC implementations, > > > as long as all the new ones can use your new generic code. > > > > Thanks for explaining once again. Do you have any issues with us > > reducing the number of supported boards and/or SoCs? > > No, I'm sure you know who the users of the board files in upstream kernels > are. If someone comes up with a good reason why one of the files is > needed after all, we can always revert the removal at a later point. > > I'm definitely in favor of removing known unused code that gets in the way > of progress and adding clean code as quickly as we can review it. Hi Arnd, thanks for clarifying this. I am in complete agreement.
Hi Olof, Hi Arnd, This pull request is based on renesas-pinmux-for-v3.11, which you have already pulled, in order to provide pre-requisites. The following changes since commit 5fcf4a3c3a5bc08bf72a50ef1332501a3c1b96bb: ARM: shmobile: marzen: Use RCAR_GP_PIN macro (2013-06-05 17:18:24 +0900) are available in the git repository at: git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-cleanup-boot-for-v3.11 for you to fetch changes up to 9da629661d207299ad119a6735eb2411f54fd45f: ARM: shmobile: Remove Bonito board support (2013-06-13 14:26:04 +0900) ---------------------------------------------------------------- Renesas ARM based SoC boot cleanup for v3.11 Work by Magnus Damm and others to clean up the boot of and move things closer to supporting MULTIARCH. As a side effect of this work it was decided to remove support for two boards, Bonito and APE4EVM. Those patches are included in this series as they depend on earlier patches in the series. ---------------------------------------------------------------- Kuninori Morimoto (1): ARM: shmobile: Remove Bonito board support Magnus Damm (14): ARM: shmobile: uImage load address rework ARM: shmobile: Let romImage rely on default ATAGS ARM: shmobile: Remove romImage CONFIG_MEMORY_START ARM: shmobile: Rework sh7372 sleep code to use virt_to_phys() ARM: shmobile: Add SMP boot function and argument ARM: shmobile: Add SCU boot function using argument ARM: shmobile: r8a7779 SMP with SCU boot fn and args ARM: shmobile: sh73a0 SMP with SCU boot fn and args ARM: shmobile: EMEV2 SMP with SCU boot fn and args ARM: shmobile: Remove old SCU boot code ARM: shmobile: Enable ARM_PATCH_PHYS_VIRT ARM: shmobile: Remove MEMORY_START/SIZE ARM: shmobile: Remove mach/memory.h ARM: shmobile: Remove AP4EVB board support arch/arm/Kconfig | 2 +- arch/arm/boot/compressed/head-shmobile.S | 21 +- arch/arm/configs/ap4evb_defconfig | 56 - arch/arm/configs/bonito_defconfig | 72 -- arch/arm/mach-shmobile/Kconfig | 58 - arch/arm/mach-shmobile/Makefile | 2 - arch/arm/mach-shmobile/Makefile.boot | 18 +- arch/arm/mach-shmobile/board-ap4evb.c | 1310 -------------------- arch/arm/mach-shmobile/board-bonito.c | 502 -------- arch/arm/mach-shmobile/headsmp-scu.S | 29 +- arch/arm/mach-shmobile/headsmp.S | 13 +- arch/arm/mach-shmobile/include/mach/common.h | 6 +- .../arm/mach-shmobile/include/mach/head-ap4evb.txt | 93 -- arch/arm/mach-shmobile/include/mach/memory.h | 7 - arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h | 29 - arch/arm/mach-shmobile/include/mach/mmc.h | 4 +- arch/arm/mach-shmobile/include/mach/sh7372.h | 2 + arch/arm/mach-shmobile/include/mach/zboot.h | 6 +- arch/arm/mach-shmobile/pm-sh7372.c | 3 + arch/arm/mach-shmobile/sleep-sh7372.S | 5 +- arch/arm/mach-shmobile/smp-emev2.c | 6 +- arch/arm/mach-shmobile/smp-r8a7779.c | 6 +- arch/arm/mach-shmobile/smp-sh73a0.c | 6 +- 23 files changed, 68 insertions(+), 2188 deletions(-) delete mode 100644 arch/arm/configs/ap4evb_defconfig delete mode 100644 arch/arm/configs/bonito_defconfig delete mode 100644 arch/arm/mach-shmobile/board-ap4evb.c delete mode 100644 arch/arm/mach-shmobile/board-bonito.c delete mode 100644 arch/arm/mach-shmobile/include/mach/head-ap4evb.txt delete mode 100644 arch/arm/mach-shmobile/include/mach/memory.h delete mode 100644 arch/arm/mach-shmobile/include/mach/mmc-ap4eb.h