diff mbox

[U-Boot] nand/fsl_elbc: detect page size at runtime

Message ID 20130226230050.GA11613@home.buserror.net
State Accepted
Delegated to: Scott Wood
Headers show

Commit Message

Scott Wood Feb. 26, 2013, 11 p.m. UTC 
This avoids needing a separate U-Boot config when some revisions
of a board have small-page NAND and other revisions have large-page
NAND (except for NAND SPL targets).

CONFIG_FSL_ELBC_FMR is removed -- it was never used nor documented, and
it gets in the way of this change.

Signed-off-by: Scott Wood <scottwood@freescale.com>
---
 drivers/mtd/nand/fsl_elbc_nand.c |   39 +++++++++++++++++++++-----------------
 1 file changed, 22 insertions(+), 17 deletions(-)

Comments

Scott Wood May 22, 2013, 9:13 p.m. UTC | #1 
On Tue, Feb 26, 2013 at 01:00:50PM -0000, Scott Wood wrote:
> This avoids needing a separate U-Boot config when some revisions
> of a board have small-page NAND and other revisions have large-page
> NAND (except for NAND SPL targets).
> 
> CONFIG_FSL_ELBC_FMR is removed -- it was never used nor documented, and
> it gets in the way of this change.
> 
> Signed-off-by: Scott Wood <scottwood@freescale.com>
> 
> ---
> drivers/mtd/nand/fsl_elbc_nand.c |   39 +++++++++++++++++++++-----------------
>  1 file changed, 22 insertions(+), 17 deletions(-)

Applied to u-boot-nand-flash.

-Scott
diff mbox

Patch

diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/fsl_elbc_nand.c
index 834a8a6..fb34d12 100644
--- a/drivers/mtd/nand/fsl_elbc_nand.c
+++ b/drivers/mtd/nand/fsl_elbc_nand.c
@@ -756,20 +756,8 @@  static int fsl_elbc_chip_init(int devnum, u8 *addr)
 	nand->ecc.read_page = fsl_elbc_read_page;
 	nand->ecc.write_page = fsl_elbc_write_page;
 
-#ifdef CONFIG_FSL_ELBC_FMR
-	priv->fmr = CONFIG_FSL_ELBC_FMR;
-#else
 	priv->fmr = (15 << FMR_CWTO_SHIFT) | (2 << FMR_AL_SHIFT);
 
-	/*
-	 * Hardware expects small page has ECCM0, large page has ECCM1
-	 * when booting from NAND.  Board config can override if not
-	 * booting from NAND.
-	 */
-	if (or & OR_FCM_PGS)
-		priv->fmr |= FMR_ECCM;
-#endif
-
 	/* If CS Base Register selects full hardware ECC then use it */
 	if ((br & BR_DECC) == BR_DECC_CHK_GEN) {
 		nand->ecc.mode = NAND_ECC_HW;
@@ -786,11 +774,26 @@  static int fsl_elbc_chip_init(int devnum, u8 *addr)
 		nand->ecc.mode = NAND_ECC_SOFT;
 	}
 
+	ret = nand_scan_ident(mtd, 1, NULL);
+	if (ret)
+		return ret;
+
 	/* Large-page-specific setup */
-	if (or & OR_FCM_PGS) {
+	if (mtd->writesize == 2048) {
+		setbits_be32(&elbc_ctrl->regs->bank[priv->bank].or,
+			     OR_FCM_PGS);
+		in_be32(&elbc_ctrl->regs->bank[priv->bank].or);
+
 		priv->page_size = 1;
 		nand->badblock_pattern = &largepage_memorybased;
 
+		/*
+		 * Hardware expects small page has ECCM0, large page has
+		 * ECCM1 when booting from NAND, and we follow that even
+		 * when not booting from NAND.
+		 */
+		priv->fmr |= FMR_ECCM;
+
 		/* adjust ecc setup if needed */
 		if ((br & BR_DECC) == BR_DECC_CHK_GEN) {
 			nand->ecc.steps = 4;
@@ -798,12 +801,14 @@  static int fsl_elbc_chip_init(int devnum, u8 *addr)
 					   &fsl_elbc_oob_lp_eccm1 :
 					   &fsl_elbc_oob_lp_eccm0;
 		}
+	} else if (mtd->writesize == 512) {
+		clrbits_be32(&elbc_ctrl->regs->bank[priv->bank].or,
+			     OR_FCM_PGS);
+		in_be32(&elbc_ctrl->regs->bank[priv->bank].or);
+	} else {
+		return -ENODEV;
 	}
 
-	ret = nand_scan_ident(mtd, 1, NULL);
-	if (ret)
-		return ret;
-
 	ret = nand_scan_tail(mtd);
 	if (ret)
 		return ret;