| Message ID | 201209042008.q84K88cJ015036@int-mx11.intmail.prod.int.phx2.redhat.com |
|---|---|
| State | New |
| Headers | show |
On 04.09.2012, at 16:08, Jason Baron wrote: > While testing q35, I found that windows 7 (specifically, windows 7 ultimate > with sp1 x64), wouldn't install because it can't find the cdrom or disk drive. > The failure message is: 'A required cd/dvd device driver is missing. If you > have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now.' > This can also be reproduced on piix by adding an ahci controller, and > observing that windows 7 does not see any devices behind it. > > The problem is that when windows issues a HBA reset, qemu does not reset the > individual ports' PxCMD register. Windows 7 then reads back the PxCMD register > and presumably assumes that the ahci controller has already been initialized. > Windows then never sets up the PxIE register to enable interrupts, and thus it > never gets irqs back when it sends ata device inquiry commands. > > This change brings qemu into ahci 1.3 specification compliance. > > Section 10.4.3 HBA Reset: > > " > When GHC.HR is set to '1', GHC.AE, GHC.IE, the IS register, and all port > register fields (except PxFB/PxFBU/PxCLB/PxCLBU) that are not HwInit in the > HBA's register memory space are reset. > " > > I've also re-tested Fedora 16 and 17 to verify that they continue to work with > this change. > > Signed-off-by: Jason Baron <jbaron@redhat.com> Awesome, a lot cleaner now :). Acked-by: Alexander Graf <agraf@suse.de>
Am 05.09.2012 05:28, schrieb Alexander Graf: > > On 04.09.2012, at 16:08, Jason Baron wrote: > >> While testing q35, I found that windows 7 (specifically, windows 7 ultimate >> with sp1 x64), wouldn't install because it can't find the cdrom or disk drive. >> The failure message is: 'A required cd/dvd device driver is missing. If you >> have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now.' >> This can also be reproduced on piix by adding an ahci controller, and >> observing that windows 7 does not see any devices behind it. >> >> The problem is that when windows issues a HBA reset, qemu does not reset the >> individual ports' PxCMD register. Windows 7 then reads back the PxCMD register >> and presumably assumes that the ahci controller has already been initialized. >> Windows then never sets up the PxIE register to enable interrupts, and thus it >> never gets irqs back when it sends ata device inquiry commands. >> >> This change brings qemu into ahci 1.3 specification compliance. >> >> Section 10.4.3 HBA Reset: >> >> " >> When GHC.HR is set to '1', GHC.AE, GHC.IE, the IS register, and all port >> register fields (except PxFB/PxFBU/PxCLB/PxCLBU) that are not HwInit in the >> HBA's register memory space are reset. >> " >> >> I've also re-tested Fedora 16 and 17 to verify that they continue to work with >> this change. >> >> Signed-off-by: Jason Baron <jbaron@redhat.com> > > Awesome, a lot cleaner now :). > > Acked-by: Alexander Graf <agraf@suse.de> Thanks, applied to block-next. Kevin
diff --git a/hw/ide/ahci.c b/hw/ide/ahci.c index 3d41771..97a0fa9 100644 --- a/hw/ide/ahci.c +++ b/hw/ide/ahci.c @@ -1175,7 +1175,6 @@ void ahci_init(AHCIState *s, DeviceState *qdev, DMAContext *dma, int ports) ad->port_no = i; ad->port.dma = &ad->dma; ad->port.dma->ops = &ahci_dma_ops; - ad->port_regs.cmd = PORT_CMD_SPIN_UP | PORT_CMD_POWER_ON; } } @@ -1199,6 +1198,7 @@ void ahci_reset(AHCIState *s) pr->irq_stat = 0; pr->irq_mask = 0; pr->scr_ctl = 0; + pr->cmd = PORT_CMD_SPIN_UP | PORT_CMD_POWER_ON; ahci_reset_port(s, i); } }
While testing q35, I found that windows 7 (specifically, windows 7 ultimate with sp1 x64), wouldn't install because it can't find the cdrom or disk drive. The failure message is: 'A required cd/dvd device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now.' This can also be reproduced on piix by adding an ahci controller, and observing that windows 7 does not see any devices behind it. The problem is that when windows issues a HBA reset, qemu does not reset the individual ports' PxCMD register. Windows 7 then reads back the PxCMD register and presumably assumes that the ahci controller has already been initialized. Windows then never sets up the PxIE register to enable interrupts, and thus it never gets irqs back when it sends ata device inquiry commands. This change brings qemu into ahci 1.3 specification compliance. Section 10.4.3 HBA Reset: " When GHC.HR is set to '1', GHC.AE, GHC.IE, the IS register, and all port register fields (except PxFB/PxFBU/PxCLB/PxCLBU) that are not HwInit in the HBA's register memory space are reset. " I've also re-tested Fedora 16 and 17 to verify that they continue to work with this change. Signed-off-by: Jason Baron <jbaron@redhat.com> --- changes in v2: -continue to set PORT_CMD_SPIN_UP, PORT_CMD_POWER_ON on reset (Kevin Wolf) -drop cmd init in ahci_init() (Alexander Graf) hw/ide/ahci.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)