Message ID | 1337955762-19157-2-git-send-email-s.hauer@pengutronix.de |
---|---|
State | Accepted |
Commit | 4a43faf54e9173b6acce37cf7f053fc9515a2cdf |
Headers | show |
On 05/25/2012 07:22 AM, Sascha Hauer wrote: > Since this commit: > > commit 6a918bade9dab40aaef80559bd1169c69e8d69cb > Author: Mike Dunn <mikedunn@newsguy.com> > Date: Sun Mar 11 14:21:11 2012 -0700 > > mtd: flash drivers set ecc strength > > The mxc_nand driver fails with: > > Driver must set ecc.strength when using hardware ECC > > This is because nand_scan_tail checks for correct ecc strength > settings, so we must set them up before nand_scan_tail. Oops, sorry Sascha. This was compile-tested only, but I should have ensured strength was set before call to nand_scan_tail(). Thanks, Mike
On Fri, 2012-05-25 at 16:22 +0200, Sascha Hauer wrote: > Since this commit: > > commit 6a918bade9dab40aaef80559bd1169c69e8d69cb > Author: Mike Dunn <mikedunn@newsguy.com> > Date: Sun Mar 11 14:21:11 2012 -0700 > > mtd: flash drivers set ecc strength > > The mxc_nand driver fails with: > > Driver must set ecc.strength when using hardware ECC > > This is because nand_scan_tail checks for correct ecc strength > settings, so we must set them up before nand_scan_tail. Pushed this one to l2-mtd.git as well, thanks!
diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c index 4d27ddc..aaf042b 100644 --- a/drivers/mtd/nand/mxc_nand.c +++ b/drivers/mtd/nand/mxc_nand.c @@ -1485,12 +1485,6 @@ static int __init mxcnd_probe(struct platform_device *pdev) else if (mtd->writesize == 4096) this->ecc.layout = host->devtype_data->ecclayout_4k; - /* second phase scan */ - if (nand_scan_tail(mtd)) { - err = -ENXIO; - goto escan; - } - if (this->ecc.mode == NAND_ECC_HW) { if (nfc_is_v1()) this->ecc.strength = 1; @@ -1498,6 +1492,12 @@ static int __init mxcnd_probe(struct platform_device *pdev) this->ecc.strength = (host->eccsize == 4) ? 4 : 8; } + /* second phase scan */ + if (nand_scan_tail(mtd)) { + err = -ENXIO; + goto escan; + } + /* Register the partitions */ mtd_device_parse_register(mtd, part_probes, &(struct mtd_part_parser_data){
Since this commit: commit 6a918bade9dab40aaef80559bd1169c69e8d69cb Author: Mike Dunn <mikedunn@newsguy.com> Date: Sun Mar 11 14:21:11 2012 -0700 mtd: flash drivers set ecc strength The mxc_nand driver fails with: Driver must set ecc.strength when using hardware ECC This is because nand_scan_tail checks for correct ecc strength settings, so we must set them up before nand_scan_tail. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Cc: stable@vger.kernel.org --- drivers/mtd/nand/mxc_nand.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)