@@ -1477,8 +1477,6 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
int chipnr, page, realpage, col, bytes, aligned;
struct nand_chip *chip = mtd->priv;
struct mtd_ecc_stats stats;
- int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
- int sndcmd = 1;
int ret = 0;
uint32_t readlen = ops->len;
uint32_t oobreadlen = ops->ooblen;
@@ -1509,10 +1507,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
if (realpage != chip->pagebuf || oob) {
bufpoi = aligned ? buf : chip->buffers->databuf;
- if (likely(sndcmd)) {
- chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page);
- sndcmd = 0;
- }
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page);
/*
* Now read the page into the buffer. Absent an error,
@@ -1564,13 +1559,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
}
if (!(chip->options & NAND_NO_READRDY)) {
- /*
- * Apply delay or wait for ready/busy pin. Do
- * this before the AUTOINCR check, so no
- * problems arise if a chip which does auto
- * increment is marked as NOAUTOINCR by the
- * board driver.
- */
+ /* Apply delay or wait for ready/busy pin */
if (!chip->dev_ready)
udelay(chip->chip_delay);
else
@@ -1600,13 +1589,6 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
chip->select_chip(mtd, -1);
chip->select_chip(mtd, chipnr);
}
-
- /*
- * Check, if the chip supports auto page increment or if we
- * have hit a block boundary.
- */
- if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck))
- sndcmd = 1;
}
ops->retlen = ops->len - (size_t) readlen;
@@ -1800,10 +1782,9 @@ static int nand_write_oob_syndrome(struct mtd_info *mtd,
static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
struct mtd_oob_ops *ops)
{
- int page, realpage, chipnr, sndcmd = 1;
+ int page, realpage, chipnr;
struct nand_chip *chip = mtd->priv;
struct mtd_ecc_stats stats;
- int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
int readlen = ops->ooblen;
int len;
uint8_t *buf = ops->oobbuf;
@@ -1842,20 +1823,15 @@ static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
while (1) {
if (ops->mode == MTD_OPS_RAW)
- sndcmd = chip->ecc.read_oob_raw(mtd, chip, page, sndcmd);
+ chip->ecc.read_oob_raw(mtd, chip, page, 1);
else
- sndcmd = chip->ecc.read_oob(mtd, chip, page, sndcmd);
+ chip->ecc.read_oob(mtd, chip, page, 1);
len = min(len, readlen);
buf = nand_transfer_oob(chip, buf, ops, len);
if (!(chip->options & NAND_NO_READRDY)) {
- /*
- * Apply delay or wait for ready/busy pin. Do this
- * before the AUTOINCR check, so no problems arise if a
- * chip which does auto increment is marked as
- * NOAUTOINCR by the board driver.
- */
+ /* Apply delay or wait for ready/busy pin */
if (!chip->dev_ready)
udelay(chip->chip_delay);
else
@@ -1876,13 +1852,6 @@ static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
chip->select_chip(mtd, -1);
chip->select_chip(mtd, chipnr);
}
-
- /*
- * Check, if the chip supports auto page increment or if we
- * have hit a block boundary.
- */
- if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck))
- sndcmd = 1;
}
ops->oobretlen = ops->ooblen;
The NAND_NO_AUTOINCR option is always set, so we will kill the option and make "no autoincrement" the default behavior for nand_base.c. Thus, we should remove the code which decides whether or not to send the NAND_CMD_READ0 command. Instead, we unconditionally send the command. Signed-off-by: Brian Norris <computersforpeace@gmail.com> --- drivers/mtd/nand/nand_base.c | 43 +++++------------------------------------ 1 files changed, 6 insertions(+), 37 deletions(-)