Message ID | 20231117074554.700970-1-anshulusr@gmail.com |
---|---|
State | Not Applicable |
Headers | show |
Series | [v2,1/2] dt-bindings: iio: light: add ltr390 | expand |
Context | Check | Description |
---|---|---|
robh/checkpatch | warning | total: 0 errors, 1 warnings, 56 lines checked |
robh/patch-applied | success | |
robh/dtbs-check | warning | build log |
robh/dt-meta-schema | success |
On 17/11/2023 08:45, Anshul Dalal wrote: > Add binding for Lite-On LTR390 which is an Ambient/UV light sensor that > communicates over i2c with an address of 0x53. > > Datasheet: > https://optoelectronics.liteon.com/upload/download/DS86-2015-0004/LTR-390UV_Final_%20DS_V1%201.pdf > > Signed-off-by: Anshul Dalal <anshulusr@gmail.com> > --- Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Best regards, Krzysztof
On Fri, 17 Nov 2023 13:15:52 +0530 Anshul Dalal <anshulusr@gmail.com> wrote: > Add binding for Lite-On LTR390 which is an Ambient/UV light sensor that > communicates over i2c with an address of 0x53. > > Datasheet: > https://optoelectronics.liteon.com/upload/download/DS86-2015-0004/LTR-390UV_Final_%20DS_V1%201.pdf > > Signed-off-by: Anshul Dalal <anshulusr@gmail.com> > --- > > Changes for v2: > - Added missing properties in the example > --- > .../bindings/iio/light/liteon,ltr390.yaml | 56 +++++++++++++++++++ > 1 file changed, 56 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/light/liteon,ltr390.yaml > > diff --git a/Documentation/devicetree/bindings/iio/light/liteon,ltr390.yaml b/Documentation/devicetree/bindings/iio/light/liteon,ltr390.yaml > new file mode 100644 > index 000000000000..5d98ef2af74d > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/light/liteon,ltr390.yaml > @@ -0,0 +1,56 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/light/liteon,ltr390.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Lite-On LTR390 ALS and UV Sensor > + > +description: | > + The Lite-On LTR390 is an ALS (Ambient Light Sensor) and a UV sensor in a > + single package with i2c address of 0x53. > + > + Datasheet: > + https://optoelectronics.liteon.com/upload/download/DS86-2015-0004/LTR-390UV_Final_%20DS_V1%201.pdf > + > +maintainers: > + - Anshul Dalal <anshulusr@gmail.com> > + > +properties: > + compatible: > + enum: > + - liteon,ltr390 > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + description: | > + Level interrupt pin with open drain output. > + The sensor pulls this pin low when the measured reading is greater than > + some configured threshold. > + > + vdd-supply: true > + > +required: > + - compatible > + - reg Same comment on vdd-supply here as in the other drivers. Not vital, but contention has become to add any supplies to required that have to be turned on, whether or not the kernel cares about them. Note I'd prefer drivers to use the trivial devm_regulator_get_enable() call anyway to turn them on at probe and off at remove. That's simple enough to do without needing testing with real controllable regulators. > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/irq.h> > + > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + > + light-sensor@53 { > + compatible = "liteon,ltr390"; > + reg = <0x53>; > + interrupts = <18 IRQ_TYPE_EDGE_FALLING>; > + vdd-supply = <&vdd_regulator>; > + }; > + };
On Fri, 17 Nov 2023 13:15:53 +0530 Anshul Dalal <anshulusr@gmail.com> wrote: > Implements driver for the Ambient/UV Light sensor LTR390. > The driver exposes two ways of getting sensor readings: > 1. Raw UV Counts directly from the sensor > 2. The computed UV Index value with a percision of 2 decimal places > > NOTE: Ambient light sensing has not been implemented yet. > > Datasheet: > https://optoelectronics.liteon.com/upload/download/DS86-2015-0004/LTR-390UV_Final_%20DS_V1%201.pdf Make this a formal Datasheet tag, just before the Signed-off-by below > > Driver tested on RPi Zero 2W > > Signed-off-by: Anshul Dalal <anshulusr@gmail.com> Hi Anshul, Some comments on this one inline. Some of these overlap with comments on the other drivers you've submitted. Normally I'd moan about sending too many drivers at a time, but fair enough given you sent them out over a couple of weeks and just happened to hit time when I was travelling. My main question in here is why have the two channels - conversion looks linear so you should be fine exposing IIO_CHAN_INFO_RAW + IIO_CHAN_INFO_SCALE on a single channel and leaving userspace to do the maths. Jonathan > diff --git a/drivers/iio/light/ltr390.c b/drivers/iio/light/ltr390.c > new file mode 100644 > index 000000000000..67ca028ce828 > --- /dev/null > +++ b/drivers/iio/light/ltr390.c > @@ -0,0 +1,232 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +/* > + * IIO driver for Lite-On LTR390 ALS and UV sensor > + * (7-bit I2C slave address 0x53) > + * > + * Based on the work of: > + * Shreeya Patel and Shi Zhigang (LTRF216 Driver) > + * > + * Copyright (C) 2023 Anshul Dalal <anshulusr@gmail.com> > + * > + * Datasheet: > + * https://optoelectronics.liteon.com/upload/download/DS86-2015-0004/LTR-390UV_Final_%20DS_V1%201.pdf > + * > + * TODO: > + * - Support for configurable gain and resolution Not using PROCESSED will help with this, so I'd drop that even in this initial driver. > + * - Sensor suspend/resume support > + * - Add support for reading the ALS > + * - Interrupt support > + */ > + > +#include <asm/unaligned.h> Put this in a block of includes after the linux ones. > +#include <linux/delay.h> > +#include <linux/i2c.h> > +#include <linux/iio/iio.h> > +#include <linux/math.h> > +#include <linux/module.h> > +#include <linux/mutex.h> > +#include <linux/regmap.h> > + > +#define LTR390_DEVICE_NAME "ltr390" > + > +#define LTR390_MAIN_CTRL 0x00 > +#define LTR390_PART_ID 0x06 > +#define LTR390_UVS_DATA 0x10 > + > +#define LTR390_SW_RESET BIT(4) > +#define LTR390_UVS_MODE BIT(3) > +#define LTR390_SENSOR_ENABLE BIT(1) > + > +#define LTR390_PART_NUMBER_ID 0xb > +#define LTR390_FRACTIONAL_PERCISION 100 > + > +/* > + * At 20-bit resolution (integration time: 400ms) and 18x gain, 2300 counts of > + * the sensor are equal to 1 UV Index [Datasheet Page#8]. > + * > + * For the default resolution of 18-bit (integration time: 100ms) and default > + * gain of 3x, the counts/uvi are calculated as follows: > + * 2300 / ((3/18) * (100/400)) = 95.83 > + */ > +#define LTR390_COUNTS_PER_UVI 96 > + > +/* > + * Window Factor is needed when the device is under Window glass with coated > + * tinted ink. This is to compensate for the light loss due to the lower > + * transmission rate of the window glass and helps * in calculating lux. > + */ > +#define LTR390_WINDOW_FACTOR 1 > + > +struct ltr390_data { > + struct regmap *regmap; > + struct i2c_client *client; > + struct mutex lock; All locks need a comment explaining the scope of data they protect. Note that regmap and the i2c bus will have their own locks by default so I'm not sure you need one here at all as I'm not seeing read modify write cycles or anything like that (I might be missing one though!) > +}; > + > +static const struct regmap_config ltr390_regmap_config = { > + .name = LTR390_DEVICE_NAME, > + .reg_bits = 8, > + .reg_stride = 1, > + .val_bits = 8, > +}; > + > +static int ltr390_register_read(struct ltr390_data *data, u8 register_address) > +{ > + struct device *dev = &data->client->dev; > + int ret; > + u8 recieve_buffer[3]; > + > + mutex_lock(&data->lock); guard(mutex)(&data->lock); here then you can just return directly without worrying about manual unlocking of the mutex. This stuff is fairly new in the kernel but very useful for cases like this! I have a set of driver cleanup that I'll send out that does this in a few IIO drivers, once I've caught up with reviews etc. This isn't a critical path where we have to care that we will then unlock after the maths to extract value in the final line of the function. > + > + ret = regmap_bulk_read(data->regmap, register_address, recieve_buffer, > + sizeof(recieve_buffer)); > + if (ret) { > + dev_err(dev, "failed to read measurement data: %d\n", ret); > + mutex_unlock(&data->lock); > + return ret; > + } > + > + mutex_unlock(&data->lock); > + return get_unaligned_le24(recieve_buffer); > +} > + > +static int ltr390_get_uv_index(struct ltr390_data *data) > +{ > + int ret; > + int uv_index; > + > + ret = ltr390_register_read(data, LTR390_UVS_DATA); > + if (ret < 0) > + return ret; > + > + uv_index = DIV_ROUND_CLOSEST(ret * LTR390_FRACTIONAL_PERCISION * > + LTR390_WINDOW_FACTOR, > + LTR390_COUNTS_PER_UVI); This looks like a linear conversion. Perhaps make it a userspace problem as division much easier in userspace where floating point is available. > + > + return uv_index; > +} > + > + > +static const struct iio_chan_spec ltr390_channels[] = { > + { > + .type = IIO_UVINDEX, > + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) > + }, > + { > + .type = IIO_INTENSITY, > + .channel2 = IIO_MOD_LIGHT_UV, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) > + }, > +}; > + > +static int ltr390_probe(struct i2c_client *client) > +{ > + struct ltr390_data *data; > + struct iio_dev *indio_dev; > + int ret, part_number; > + > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); > + if (!indio_dev) > + return -ENOMEM; > + > + data = iio_priv(indio_dev); > + > + data->regmap = devm_regmap_init_i2c(client, <r390_regmap_config); > + if (IS_ERR(data->regmap)) > + return dev_err_probe(&client->dev, PTR_ERR(data->regmap), There are quite a few &client->dev in here. I'd introduce struct device *dev = &client->dev; as a local variable then use that to shorten all those lines a little. > + "regmap initialization failed\n"); > + > + data->client = client; > + i2c_set_clientdata(client, indio_dev); Why set this? I don' think you are using it. > + mutex_init(&data->lock); > + > + indio_dev->info = <r390_info; > + indio_dev->channels = ltr390_channels; > + indio_dev->num_channels = ARRAY_SIZE(ltr390_channels); > + indio_dev->name = LTR390_DEVICE_NAME; I prefer to see strings for names like this rather than making a reviewer find the define to make sure it's of appropriate format etc. Just duplicate the string in the few places it's used. > + > + ret = regmap_read(data->regmap, LTR390_PART_ID, &part_number); > + if (ret) { > + dev_err(&client->dev, "failed to get sensor's part id: %d", > + ret); dev_err_probe() for all error prints in probe(). Some of the functionality won't matter in cases like this, but its cleaner anyway so use it everywhere + then a reviewer doesn't need to consider what might defer. > + return ret; > + } > + /* Lower 4 bits of `part_number` change with hardware revisions */ > + if (part_number >> 4 != LTR390_PART_NUMBER_ID) { > + dev_err(&client->dev, "received invalid product id: 0x%x", > + part_number); return dev_err_probe() Also, to enable device tree fallback compatibles (used when a new part is released that is completely compatible with a driver for an older one) we don't want to error out here. Fine to print a dev_info() message though to indicate we don't know if the driver is compatible or not. Please check your other drivers for this (I may have missed it!) > + return -ENODEV; > + } > + dev_dbg(&client->dev, "LTR390, product id: 0x%x\n", part_number); > + > + /* reset sensor, chip fails to respond to this, so ignore any errors */ > + regmap_set_bits(data->regmap, LTR390_MAIN_CTRL, LTR390_SW_RESET); > + > + /* Wait for the registers to reset before proceeding */ > + usleep_range(1000, 2000); > + > + ret = regmap_set_bits(data->regmap, LTR390_MAIN_CTRL, > + LTR390_SENSOR_ENABLE | LTR390_UVS_MODE); > + if (ret) { > + dev_err(&client->dev, "failed to enable the sensor: %d\n", ret); return dev_err_probe() > + return ret; > + } > + > + return devm_iio_device_register(&client->dev, indio_dev); > +} > + > +static const struct i2c_device_id ltr390_id[] = { > + { LTR390_DEVICE_NAME, 0 }, That 0 adds nothing useful so drop it. > + { /* Sentinel */ }, No comma after sentinal. > +}; > +MODULE_DEVICE_TABLE(i2c, ltr390_id); > + > +static const struct of_device_id ltr390_of_table[] = { > + { .compatible = "liteon,ltr390"}, uneven spacing. Should be one before } > + { /* Sentinel */ } > +}; > +MODULE_DEVICE_TABLE(of, ltr390_id_table); Always build test as a module. 0-day pointed this out - name here is wrong. > + > +static struct i2c_driver ltr390_driver = { > + .driver = { > + .name = LTR390_DEVICE_NAME, > + .of_match_table = ltr390_of_table, > + }, > + .probe = ltr390_probe, > + .id_table = ltr390_id, > +}; > + trivial, but we often don't have a blank line here as the structure only exists to pass to module_i2c_driver() macro so we might as well group them together. > +module_i2c_driver(ltr390_driver); > + > +MODULE_AUTHOR("Anshul Dalal <anshulusr@gmail.com>"); > +MODULE_DESCRIPTION("Lite-On LTR390 ALS and UV sensor Driver"); > +MODULE_LICENSE("GPL");
On 11/25/23 19:36, Jonathan Cameron wrote: > On Fri, 17 Nov 2023 13:15:53 +0530 > Anshul Dalal <anshulusr@gmail.com> wrote: > >> Implements driver for the Ambient/UV Light sensor LTR390. >> The driver exposes two ways of getting sensor readings: >> 1. Raw UV Counts directly from the sensor >> 2. The computed UV Index value with a percision of 2 decimal places >> >> NOTE: Ambient light sensing has not been implemented yet. >> >> Datasheet: >> https://optoelectronics.liteon.com/upload/download/DS86-2015-0004/LTR-390UV_Final_%20DS_V1%201.pdf > Make this a formal Datasheet tag, just before the Signed-off-by below Thanks for pointing it out, I was unaware of the standard formal tags. Is there any resource that lists out the formal tags that I can refer to. >> >> Driver tested on RPi Zero 2W >> >> Signed-off-by: Anshul Dalal <anshulusr@gmail.com> > > Hi Anshul, > > Some comments on this one inline. Some of these overlap with comments on the > other drivers you've submitted. Normally I'd moan about sending too many drivers > at a time, but fair enough given you sent them out over a couple of weeks and just > happened to hit time when I was travelling. > > My main question in here is why have the two channels - conversion looks linear > so you should be fine exposing IIO_CHAN_INFO_RAW + IIO_CHAN_INFO_SCALE on a > single channel and leaving userspace to do the maths. > > Jonathan This driver was my first time working with the IIO subsystem and wasn't sure about the correct way to use the channels. This should be fixed in the next revision with the UV index being reported in the following channel: static const struct iio_chan_spec ltr390_channel = { .type = IIO_UVINDEX, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE) }; With data being reported as: case IIO_CHAN_INFO_RAW: ret = ltr390_register_read(data, LTR390_UVS_DATA); if (ret < 0) return ret; *val = ret; return IIO_VAL_INT; case IIO_CHAN_INFO_SCALE: *val = LTR390_WINDOW_FACTOR; *val2 = LTR390_COUNTS_PER_UVI; return IIO_VAL_FRACTIONAL; >> diff --git a/drivers/iio/light/ltr390.c b/drivers/iio/light/ltr390.c >> new file mode 100644 >> index 000000000000..67ca028ce828 >> --- /dev/null >> +++ b/drivers/iio/light/ltr390.c >> @@ -0,0 +1,232 @@ >> +// SPDX-License-Identifier: GPL-2.0-or-later >> +/* >> + * IIO driver for Lite-On LTR390 ALS and UV sensor >> + * (7-bit I2C slave address 0x53) >> + * >> + * Based on the work of: >> + * Shreeya Patel and Shi Zhigang (LTRF216 Driver) >> + * >> + * Copyright (C) 2023 Anshul Dalal <anshulusr@gmail.com> >> + * >> + * Datasheet: >> + * https://optoelectronics.liteon.com/upload/download/DS86-2015-0004/LTR-390UV_Final_%20DS_V1%201.pdf >> + * >> + * TODO: >> + * - Support for configurable gain and resolution > > Not using PROCESSED will help with this, so I'd drop that even in this initial > driver. >>> + * - Sensor suspend/resume support >> + * - Add support for reading the ALS >> + * - Interrupt support > >> + */ >> + >> +#include <asm/unaligned.h> > > Put this in a block of includes after the linux ones. > >> +#include <linux/delay.h> >> +#include <linux/i2c.h> >> +#include <linux/iio/iio.h> >> +#include <linux/math.h> >> +#include <linux/module.h> >> +#include <linux/mutex.h> >> +#include <linux/regmap.h> >> + >> +#define LTR390_DEVICE_NAME "ltr390" >> + >> +#define LTR390_MAIN_CTRL 0x00 >> +#define LTR390_PART_ID 0x06 >> +#define LTR390_UVS_DATA 0x10 >> + >> +#define LTR390_SW_RESET BIT(4) >> +#define LTR390_UVS_MODE BIT(3) >> +#define LTR390_SENSOR_ENABLE BIT(1) >> + >> +#define LTR390_PART_NUMBER_ID 0xb >> +#define LTR390_FRACTIONAL_PERCISION 100 >> + >> +/* >> + * At 20-bit resolution (integration time: 400ms) and 18x gain, 2300 counts of >> + * the sensor are equal to 1 UV Index [Datasheet Page#8]. >> + * >> + * For the default resolution of 18-bit (integration time: 100ms) and default >> + * gain of 3x, the counts/uvi are calculated as follows: >> + * 2300 / ((3/18) * (100/400)) = 95.83 >> + */ >> +#define LTR390_COUNTS_PER_UVI 96 >> + >> +/* >> + * Window Factor is needed when the device is under Window glass with coated >> + * tinted ink. This is to compensate for the light loss due to the lower >> + * transmission rate of the window glass and helps * in calculating lux. >> + */ >> +#define LTR390_WINDOW_FACTOR 1 >> + >> +struct ltr390_data { >> + struct regmap *regmap; >> + struct i2c_client *client; >> + struct mutex lock; > > All locks need a comment explaining the scope of data they protect. > Note that regmap and the i2c bus will have their own locks by default > so I'm not sure you need one here at all as I'm not seeing read modify write > cycles or anything like that (I might be missing one though!) My goal with the mutex was to protect the sysfs though that might be unnecessary. >> +}; >> + >> +static const struct regmap_config ltr390_regmap_config = { >> + .name = LTR390_DEVICE_NAME, >> + .reg_bits = 8, >> + .reg_stride = 1, >> + .val_bits = 8, >> +}; >> + >> +static int ltr390_register_read(struct ltr390_data *data, u8 register_address) >> +{ >> + struct device *dev = &data->client->dev; >> + int ret; >> + u8 recieve_buffer[3]; >> + >> + mutex_lock(&data->lock); > > guard(mutex)(&data->lock); > here then you can just return directly without worrying about manual > unlocking of the mutex. This stuff is fairly new in the kernel but very > useful for cases like this! I have a set of driver cleanup that I'll send > out that does this in a few IIO drivers, once I've caught up with reviews etc. > > This isn't a critical path where we have to care that we will then unlock > after the maths to extract value in the final line of the function. > >> + >> + ret = regmap_bulk_read(data->regmap, register_address, recieve_buffer, >> + sizeof(recieve_buffer)); >> + if (ret) { >> + dev_err(dev, "failed to read measurement data: %d\n", ret); >> + mutex_unlock(&data->lock); >> + return ret; >> + } >> + >> + mutex_unlock(&data->lock); >> + return get_unaligned_le24(recieve_buffer); >> +} >> + >> +static int ltr390_get_uv_index(struct ltr390_data *data) >> +{ >> + int ret; >> + int uv_index; >> + >> + ret = ltr390_register_read(data, LTR390_UVS_DATA); >> + if (ret < 0) >> + return ret; >> + >> + uv_index = DIV_ROUND_CLOSEST(ret * LTR390_FRACTIONAL_PERCISION * >> + LTR390_WINDOW_FACTOR, >> + LTR390_COUNTS_PER_UVI); > > This looks like a linear conversion. Perhaps make it a userspace problem > as division much easier in userspace where floating point is available. > >> + >> + return uv_index; >> +} >> + > >> + >> +static const struct iio_chan_spec ltr390_channels[] = { >> + { >> + .type = IIO_UVINDEX, >> + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) >> + }, >> + { >> + .type = IIO_INTENSITY, >> + .channel2 = IIO_MOD_LIGHT_UV, >> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) >> + }, >> +}; >> + >> +static int ltr390_probe(struct i2c_client *client) >> +{ >> + struct ltr390_data *data; >> + struct iio_dev *indio_dev; >> + int ret, part_number; >> + >> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); >> + if (!indio_dev) >> + return -ENOMEM; >> + >> + data = iio_priv(indio_dev); >> + >> + data->regmap = devm_regmap_init_i2c(client, <r390_regmap_config); >> + if (IS_ERR(data->regmap)) >> + return dev_err_probe(&client->dev, PTR_ERR(data->regmap), > There are quite a few &client->dev in here. I'd introduce > struct device *dev = &client->dev; > as a local variable then use that to shorten all those lines a little. > >> + "regmap initialization failed\n"); >> + >> + data->client = client; >> + i2c_set_clientdata(client, indio_dev); > > Why set this? I don' think you are using it. > It seems to be necessary for regmap to work properly, I tested without it and I get an EREMOTEIO(121) when reading the part id. >> [..] Thanks for the review, Best regards, Anshul
> >> +struct ltr390_data { > >> + struct regmap *regmap; > >> + struct i2c_client *client; > >> + struct mutex lock; > > > > All locks need a comment explaining the scope of data they protect. > > Note that regmap and the i2c bus will have their own locks by default > > so I'm not sure you need one here at all as I'm not seeing read modify write > > cycles or anything like that (I might be missing one though!) > > My goal with the mutex was to protect the sysfs though that might be > unnecessary. Ok. So, there is nothing stopping multiple parallel sysfs accesses, but what you'll actually be protecting is either device or driver state, not sysfs as such. > > >> +}; > >> + > >> +static const struct regmap_config ltr390_regmap_config = { > >> + .name = LTR390_DEVICE_NAME, > >> + .reg_bits = 8, > >> + .reg_stride = 1, > >> + .val_bits = 8, > >> +}; > >> + > >> +static int ltr390_probe(struct i2c_client *client) > >> +{ > >> + struct ltr390_data *data; > >> + struct iio_dev *indio_dev; > >> + int ret, part_number; > >> + > >> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); > >> + if (!indio_dev) > >> + return -ENOMEM; > >> + > >> + data = iio_priv(indio_dev); > >> + > >> + data->regmap = devm_regmap_init_i2c(client, <r390_regmap_config); > >> + if (IS_ERR(data->regmap)) > >> + return dev_err_probe(&client->dev, PTR_ERR(data->regmap), > > There are quite a few &client->dev in here. I'd introduce > > struct device *dev = &client->dev; > > as a local variable then use that to shorten all those lines a little. > > > >> + "regmap initialization failed\n"); > >> + > >> + data->client = client; > >> + i2c_set_clientdata(client, indio_dev); > > > > Why set this? I don' think you are using it. > > > > It seems to be necessary for regmap to work properly, I tested without > it and I get an EREMOTEIO(121) when reading the part id. That's weird given regmap will have no understanding of an iio_dev. If you can do some more debugging on where that error is coming from in regmap that would be great. I suspect it's coming from down in the bus master which should not be touching this at all. What is the i2c master in this case? Jonathan > > >> [..] > > Thanks for the review, > Best regards, > Anshul
diff --git a/Documentation/devicetree/bindings/iio/light/liteon,ltr390.yaml b/Documentation/devicetree/bindings/iio/light/liteon,ltr390.yaml new file mode 100644 index 000000000000..5d98ef2af74d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/liteon,ltr390.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/liteon,ltr390.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Lite-On LTR390 ALS and UV Sensor + +description: | + The Lite-On LTR390 is an ALS (Ambient Light Sensor) and a UV sensor in a + single package with i2c address of 0x53. + + Datasheet: + https://optoelectronics.liteon.com/upload/download/DS86-2015-0004/LTR-390UV_Final_%20DS_V1%201.pdf + +maintainers: + - Anshul Dalal <anshulusr@gmail.com> + +properties: + compatible: + enum: + - liteon,ltr390 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + description: | + Level interrupt pin with open drain output. + The sensor pulls this pin low when the measured reading is greater than + some configured threshold. + + vdd-supply: true + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + light-sensor@53 { + compatible = "liteon,ltr390"; + reg = <0x53>; + interrupts = <18 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&vdd_regulator>; + }; + };
Add binding for Lite-On LTR390 which is an Ambient/UV light sensor that communicates over i2c with an address of 0x53. Datasheet: https://optoelectronics.liteon.com/upload/download/DS86-2015-0004/LTR-390UV_Final_%20DS_V1%201.pdf Signed-off-by: Anshul Dalal <anshulusr@gmail.com> --- Changes for v2: - Added missing properties in the example --- .../bindings/iio/light/liteon,ltr390.yaml | 56 +++++++++++++++++++ 1 file changed, 56 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/light/liteon,ltr390.yaml