Message ID | 20211018062428.4201-2-jaimeliao.tw@gmail.com |
---|---|
State | Superseded |
Delegated to: | Jagannadha Sutradharudu Teki |
Headers | show |
Series | Add octal DTR support for Macronix flash | expand |
On Mon, Oct 18, 2021 at 11:54 AM JaimeLiao <jaimeliao.tw@gmail.com> wrote: > > Follow patch "f6adec1af4b2f5d3012480c6cdce7743b74a6156" for adding > Macronix flash in Octal DTR mode. > > Enable Octal DTR mode with 20 dummy cycles to allow running at the > maximum supported frequency. > -https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf > > Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com> > --- > drivers/mtd/spi/Kconfig | 7 +++ > drivers/mtd/spi/spi-nor-core.c | 83 ++++++++++++++++++++++++++++++++++ > include/linux/mtd/spi-nor.h | 13 +++++- > 3 files changed, 101 insertions(+), 2 deletions(-) > > diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig > index 1b2ef37e92..67599b32c9 100644 > --- a/drivers/mtd/spi/Kconfig > +++ b/drivers/mtd/spi/Kconfig > @@ -162,6 +162,13 @@ config SPI_FLASH_MACRONIX > help > Add support for various Macronix SPI flash chips (MX25Lxxx) > > +config SPI_FLASH_MACRONIX_OCTAL What if we use exiting SPI_FLASH_MACRONIX for it? does it increasing size much? if not go for exiting macro.
Hi Jagan > > On Mon, Oct 18, 2021 at 11:54 AM JaimeLiao <jaimeliao.tw@gmail.com> wrote: > > > > Follow patch "f6adec1af4b2f5d3012480c6cdce7743b74a6156" for adding > > Macronix flash in Octal DTR mode. > > > > Enable Octal DTR mode with 20 dummy cycles to allow running at the > > maximum supported frequency. > > -https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf > > > > Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com> > > --- > > drivers/mtd/spi/Kconfig | 7 +++ > > drivers/mtd/spi/spi-nor-core.c | 83 ++++++++++++++++++++++++++++++++++ > > include/linux/mtd/spi-nor.h | 13 +++++- > > 3 files changed, 101 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig > > index 1b2ef37e92..67599b32c9 100644 > > --- a/drivers/mtd/spi/Kconfig > > +++ b/drivers/mtd/spi/Kconfig > > @@ -162,6 +162,13 @@ config SPI_FLASH_MACRONIX > > help > > Add support for various Macronix SPI flash chips (MX25Lxxx) > > > > +config SPI_FLASH_MACRONIX_OCTAL > > What if we use exiting SPI_FLASH_MACRONIX for it? does it increasing > size much? if not go for exiting macro. I want to seperate SPI_FLASH_MACRONIX and SPI_FLASH_MACRONIX_OCTAL for enabling Macronix octal support. Refer to your suggestions, checking SPI_FLASH_MACRONIX and other configuration which means octal enable is better. But I didn't found the existing configuration means "octal enable". It would be great if you can recommend the suitable configuration set for nor->fixups hooks macronix_octal_fixups. I will have v5 patchwork with the configuration checking. Thanks Jaime
On Wed, Nov 3, 2021 at 4:11 PM liao jaime <jaimeliao.tw@gmail.com> wrote: > > Hi Jagan > > > > > > On Mon, Oct 18, 2021 at 11:54 AM JaimeLiao <jaimeliao.tw@gmail.com> wrote: > > > > > > Follow patch "f6adec1af4b2f5d3012480c6cdce7743b74a6156" for adding > > > Macronix flash in Octal DTR mode. > > > > > > Enable Octal DTR mode with 20 dummy cycles to allow running at the > > > maximum supported frequency. > > > -https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf > > > > > > Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com> > > > --- > > > drivers/mtd/spi/Kconfig | 7 +++ > > > drivers/mtd/spi/spi-nor-core.c | 83 ++++++++++++++++++++++++++++++++++ > > > include/linux/mtd/spi-nor.h | 13 +++++- > > > 3 files changed, 101 insertions(+), 2 deletions(-) > > > > > > diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig > > > index 1b2ef37e92..67599b32c9 100644 > > > --- a/drivers/mtd/spi/Kconfig > > > +++ b/drivers/mtd/spi/Kconfig > > > @@ -162,6 +162,13 @@ config SPI_FLASH_MACRONIX > > > help > > > Add support for various Macronix SPI flash chips (MX25Lxxx) > > > > > > +config SPI_FLASH_MACRONIX_OCTAL > > > > What if we use exiting SPI_FLASH_MACRONIX for it? does it increasing > > size much? if not go for exiting macro. > I want to seperate SPI_FLASH_MACRONIX and SPI_FLASH_MACRONIX_OCTAL for > enabling Macronix octal support. > Refer to your suggestions, checking SPI_FLASH_MACRONIX and other > configuration which means octal enable is better. > But I didn't found the existing configuration means "octal enable". > It would be great if you can recommend the suitable configuration set > for nor->fixups hooks macronix_octal_fixups. > I will have v5 patchwork with the configuration checking. My suggestion is go with existing Macronix config, if we keep adding octal specific configs for each flash it will increase configs. Jagan.
diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig index 1b2ef37e92..67599b32c9 100644 --- a/drivers/mtd/spi/Kconfig +++ b/drivers/mtd/spi/Kconfig @@ -162,6 +162,13 @@ config SPI_FLASH_MACRONIX help Add support for various Macronix SPI flash chips (MX25Lxxx) +config SPI_FLASH_MACRONIX_OCTAL + bool "Macronix octal flash support" + depends on SPI_FLASH_MACRONIX + help + Add support for the Macronix octal flash. This is a separate config + because the fixup hooks octal enable for this flash. + config SPI_FLASH_SPANSION bool "Spansion SPI flash support" help diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c index d5d905fa5a..fdaca0a0d3 100644 --- a/drivers/mtd/spi/spi-nor-core.c +++ b/drivers/mtd/spi/spi-nor-core.c @@ -3489,6 +3489,85 @@ static struct spi_nor_fixups mt35xu512aba_fixups = { }; #endif /* CONFIG_SPI_FLASH_MT35XU */ +#if CONFIG_IS_ENABLED(SPI_FLASH_MACRONIX_OCTAL) +/** + * spi_nor_macronix_octal_dtr_enable() - set DTR OPI Enable bit in Configuration Register 2. + * @nor: pointer to a 'struct spi_nor' + * + * Set the DTR OPI Enable (DOPI) bit in Configuration Register 2. + * Bit 2 of Configuration Register 2 is the DOPI bit for Macronix like OPI memories. + * + * Return: 0 on success, -errno otherwise. + */ +static int spi_nor_macronix_octal_dtr_enable(struct spi_nor *nor) +{ + struct spi_mem_op op; + int ret; + u8 buf; + + ret = write_enable(nor); + if (ret) + return ret; + + buf = SPINOR_REG_MXIC_DC_20; + op = (struct spi_mem_op) + SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_CR2, 1), + SPI_MEM_OP_ADDR(4, SPINOR_REG_MXIC_CR2_DC, 1), + SPI_MEM_OP_NO_DUMMY, + SPI_MEM_OP_DATA_OUT(1, &buf, 1)); + + ret = spi_mem_exec_op(nor->spi, &op); + if (ret) + return ret; + + ret = spi_nor_wait_till_ready(nor); + if (ret) + return ret; + + nor->read_dummy = MXIC_MAX_DC; + ret = write_enable(nor); + if (ret) + return ret; + + buf = SPINOR_REG_MXIC_OPI_DTR_EN; + op = (struct spi_mem_op) + SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_CR2, 1), + SPI_MEM_OP_ADDR(4, SPINOR_REG_MXIC_CR2_MODE, 1), + SPI_MEM_OP_NO_DUMMY, + SPI_MEM_OP_DATA_OUT(1, &buf, 1)); + + ret = spi_mem_exec_op(nor->spi, &op); + if (ret) { + dev_err(nor->dev, "Failed to enable octal DTR mode\n"); + return ret; + } + nor->reg_proto = SNOR_PROTO_8_8_8_DTR; + + return 0; +} + +static void macronix_octal_default_init(struct spi_nor *nor) +{ + nor->octal_dtr_enable = spi_nor_macronix_octal_dtr_enable; +} + +static void macronix_octal_post_sfdp_fixup(struct spi_nor *nor, + struct spi_nor_flash_parameter *params) +{ + /* + * Adding SNOR_HWCAPS_PP_8_8_8_DTR in hwcaps.mask when + * SPI_NOR_OCTAL_DTR_READ flag exists. + */ + if (params->hwcaps.mask & SNOR_HWCAPS_READ_8_8_8_DTR) + params->hwcaps.mask |= SNOR_HWCAPS_PP_8_8_8_DTR; +} + +static struct spi_nor_fixups macronix_octal_fixups = { + .default_init = macronix_octal_default_init, + .post_sfdp = macronix_octal_post_sfdp_fixup, +}; +#endif /* CONFIG_SPI_FLASH_MACRONIX_OCTAL */ + /** spi_nor_octal_dtr_enable() - enable Octal DTR I/O if needed * @nor: pointer to a 'struct spi_nor' * @@ -3655,6 +3734,10 @@ void spi_nor_set_fixups(struct spi_nor *nor) if (!strcmp(nor->info->name, "mt35xu512aba")) nor->fixups = &mt35xu512aba_fixups; #endif + +#if CONFIG_IS_ENABLED(SPI_FLASH_MACRONIX_OCTAL) + nor->fixups = ¯onix_octal_fixups; +#endif /* SPI_FLASH_MACRONIX_OCTAL */ } int spi_nor_scan(struct spi_nor *nor) diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h index 7ddc4ba2bf..2ad579f66d 100644 --- a/include/linux/mtd/spi-nor.h +++ b/include/linux/mtd/spi-nor.h @@ -116,8 +116,17 @@ #define XSR_RDY BIT(7) /* Ready */ /* Used for Macronix and Winbond flashes. */ -#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */ -#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */ +#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */ +#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */ +#define SPINOR_OP_RD_CR2 0x71 /* Read configuration register 2 */ +#define SPINOR_OP_WR_CR2 0x72 /* Write configuration register 2 */ +#define SPINOR_OP_MXIC_DTR_RD 0xee /* Fast Read opcode in DTR mode */ +#define SPINOR_REG_MXIC_CR2_MODE 0x00000000 /* For setting octal DTR mode */ +#define SPINOR_REG_MXIC_OPI_DTR_EN 0x2 /* Enable Octal DTR */ +#define SPINOR_REG_MXIC_OPI_DTR_DIS 0x1 /* Disable Octal DTR */ +#define SPINOR_REG_MXIC_CR2_DC 0x00000300 /* For setting dummy cycles */ +#define SPINOR_REG_MXIC_DC_20 0x0 /* Setting dummy cycles to 20 */ +#define MXIC_MAX_DC 20 /* Maximum value of dummy cycles */ /* Used for Spansion flashes only. */ #define SPINOR_OP_BRWR 0x17 /* Bank register write */
Follow patch "f6adec1af4b2f5d3012480c6cdce7743b74a6156" for adding Macronix flash in Octal DTR mode. Enable Octal DTR mode with 20 dummy cycles to allow running at the maximum supported frequency. -https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com> --- drivers/mtd/spi/Kconfig | 7 +++ drivers/mtd/spi/spi-nor-core.c | 83 ++++++++++++++++++++++++++++++++++ include/linux/mtd/spi-nor.h | 13 +++++- 3 files changed, 101 insertions(+), 2 deletions(-)