Message ID | 1311715171-13128-4-git-send-email-u-boot@lakedaemon.net |
---|---|
State | Superseded |
Headers | show |
> -----Original Message----- > From: Jason Cooper [mailto:u-boot@lakedaemon.net] > Sent: Wednesday, July 27, 2011 2:49 AM > To: clint@debian.org; wd@denx.de; Prafulla Wadaskar > Cc: u-boot@lists.denx.de; Prabhanjan Sarnaik; Ashish Karkare; Siddarth > Gore; bdale@gag.com; Jason Cooper > Subject: RFC [PATCH 4/5 v5] dreamplug: initial board support. > > Copied wholeheartedly from board/Marvell/guruplug and modified to add > support > for SPI NOR flash. > > Also, the following features are used: > - Use the Marvell Integrated RTC. > - display Marvell CPU/L2/etc speeds if requested. > > Note: this still uses MACH_TYPE_GURUPLUG until MACH_TYPE_DREAMPLUG is > accepted > into mainline Linux. The source from Globalscale did the same. > > Signed-off-by: Jason Cooper <u-boot@lakedaemon.net> > --- There is no change log for all previous versions. Please put them here. Ref: http://www.denx.de/wiki/view/U-Boot/Patches#Sending_updated_patch_versions > MAINTAINERS | 4 + > MAKEALL | 1 + > board/Marvell/dreamplug/Makefile | 54 +++++++++++ > board/Marvell/dreamplug/dreamplug.c | 157 > ++++++++++++++++++++++++++++++++ > board/Marvell/dreamplug/dreamplug.h | 42 +++++++++ > board/Marvell/dreamplug/kwbimage.cfg | 163 > ++++++++++++++++++++++++++++++++++ > boards.cfg | 1 + > include/configs/dreamplug.h | 138 > ++++++++++++++++++++++++++++ > 8 files changed, 560 insertions(+), 0 deletions(-) > create mode 100644 board/Marvell/dreamplug/Makefile > create mode 100644 board/Marvell/dreamplug/dreamplug.c > create mode 100644 board/Marvell/dreamplug/dreamplug.h > create mode 100644 board/Marvell/dreamplug/kwbimage.cfg > create mode 100644 include/configs/dreamplug.h > > diff --git a/MAINTAINERS b/MAINTAINERS > index 2bba7b4..9affbea 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -70,6 +70,10 @@ Conn Clark <clark@esteem.com> > > ESTEEM192E MPC8xx > > +Jason Cooper <u-boot@lakedaemon.net> > + > + dreamplug ARM926EJS (Kirkwood SoC) > + > Joe D'Abbraccio <ljd015@freescale.com> > > MPC837xERDB MPC837x > diff --git a/MAKEALL b/MAKEALL > index 51db13e..55a122f 100755 > --- a/MAKEALL > +++ b/MAKEALL > @@ -335,6 +335,7 @@ LIST_ARM9=" \ > cp966 \ > da830evm \ > da850evm \ > + dreamplug \ > edb9301 \ > edb9302 \ > edb9302a \ > diff --git a/board/Marvell/dreamplug/Makefile > b/board/Marvell/dreamplug/Makefile > new file mode 100644 > index 0000000..9ee5406 > --- /dev/null > +++ b/board/Marvell/dreamplug/Makefile > @@ -0,0 +1,54 @@ > +# > +# (C) Copyright 2011 > +# Jason Cooper <u-boot@lakedaemon.net> > +# > +# Based on work by: > +# Marvell Semiconductor <www.marvell.com> > +# Written-by: Siddarth Gore <gores@marvell.com> > +# > +# See file CREDITS for list of people who contributed to this > +# project. > +# > +# This program is free software; you can redistribute it and/or > +# modify it under the terms of the GNU General Public License as > +# published by the Free Software Foundation; either version 2 of > +# the License, or (at your option) any later version. > +# > +# This program is distributed in the hope that it will be useful, > +# but WITHOUT ANY WARRANTY; without even the implied warranty of > +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > +# GNU General Public License for more details. > +# > +# You should have received a copy of the GNU General Public License > +# along with this program; if not, write to the Free Software > +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > +# MA 02110-1301 USA > +# > + > +include $(TOPDIR)/config.mk > + > +LIB = $(obj)lib$(BOARD).o > + > +COBJS := dreamplug.o > + > +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) > +OBJS := $(addprefix $(obj),$(COBJS)) > +SOBJS := $(addprefix $(obj),$(SOBJS)) > + > +$(LIB): $(obj).depend $(OBJS) $(SOBJS) > + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) > + > +clean: > + rm -f $(SOBJS) $(OBJS) > + > +distclean: clean > + rm -f $(LIB) core *.bak .depend > + > +####################################################################### > ## > + > +# defines $(obj).depend target > +include $(SRCTREE)/rules.mk > + > +sinclude $(obj).depend > + > +####################################################################### > ## > diff --git a/board/Marvell/dreamplug/dreamplug.c > b/board/Marvell/dreamplug/dreamplug.c > new file mode 100644 > index 0000000..cdc094a > --- /dev/null > +++ b/board/Marvell/dreamplug/dreamplug.c > @@ -0,0 +1,157 @@ > +/* > + * (C) Copyright 2011 > + * Jason Cooper <u-boot@lakedaemon.net> > + * > + * Based on work by: > + * Marvell Semiconductor <www.marvell.com> > + * Written-by: Siddarth Gore <gores@marvell.com> > + * > + * See file CREDITS for list of people who contributed to this > + * project. > + * > + * This program is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of > + * the License, or (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * You should have received a copy of the GNU General Public License > + * along with this program; if not, write to the Free Software > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > + * MA 02110-1301 USA > + */ > + > +#include <common.h> > +#include <miiphy.h> > +#include <asm/arch/kirkwood.h> > +#include <asm/arch/mpp.h> > +#include "dreamplug.h" > + > +DECLARE_GLOBAL_DATA_PTR; > + > +int board_early_init_f(void) > +{ > + /* > + * default gpio configuration > + * There are maximum 64 gpios controlled through 2 sets of registers > + * the below configuration configures mainly initial LED status > + */ > + kw_config_gpio(DREAMPLUG_OE_VAL_LOW, > + DREAMPLUG_OE_VAL_HIGH, > + DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH); > + > + /* Multi-Purpose Pins Functionality configuration */ > + u32 kwmpp_config[] = { > + MPP0_SPI_SCn, /* SPI Flash */ > + MPP1_SPI_MOSI, > + MPP2_SPI_SCK, > + MPP3_SPI_MISO, > + MPP4_NF_IO6, > + MPP5_NF_IO7, > + MPP6_SYSRST_OUTn, > + MPP7_GPO, > + MPP8_TW_SDA, > + MPP9_TW_SCK, > + MPP10_UART0_TXD, /* Serial */ > + MPP11_UART0_RXD, > + MPP12_SD_CLK, /* SDIO Slot */ > + MPP13_SD_CMD, > + MPP14_SD_D0, > + MPP15_SD_D1, > + MPP16_SD_D2, > + MPP17_SD_D3, > + MPP18_NF_IO0, > + MPP19_NF_IO1, > + MPP20_GE1_0, /* Gigabit Ethernet */ > + MPP21_GE1_1, > + MPP22_GE1_2, > + MPP23_GE1_3, > + MPP24_GE1_4, > + MPP25_GE1_5, > + MPP26_GE1_6, > + MPP27_GE1_7, > + MPP28_GE1_8, > + MPP29_GE1_9, > + MPP30_GE1_10, > + MPP31_GE1_11, > + MPP32_GE1_12, > + MPP33_GE1_13, > + MPP34_GE1_14, > + MPP35_GE1_15, > + MPP36_GPIO, > + MPP37_GPIO, > + MPP38_GPIO, > + MPP39_GPIO, > + MPP40_TDM_SPI_SCK, > + MPP41_TDM_SPI_MISO, > + MPP42_TDM_SPI_MOSI, > + MPP43_GPIO, > + MPP44_GPIO, > + MPP45_GPIO, > + MPP46_GPIO, /* Wifi AP LED */ > + MPP47_GPIO, > + MPP48_GPIO, /* Wifi LED */ It is better if you can comment about rest other GPIOSs with their assigned functionality. > + MPP49_GPIO, > + 0 > + }; > + kirkwood_mpp_conf(kwmpp_config); > + return 0; > +} > + > +int board_init(void) > +{ > + /* > + * arch number of board > + * XXX: change to MACH_TYPE_DREAMPLUG once in Linux mainline. > + */ > + gd->bd->bi_arch_number = MACH_TYPE_GURUPLUG; I think this board should have some delta to guruplug? I think you should have different machine ID here. BTW: what is delta w.r.to guruplug? > + > + /* adress of boot parameters */ > + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; > + > + return 0; > +} > + > +#ifdef CONFIG_RESET_PHY_R > +void mv_phy_88e1121_init(char *name) > +{ > + u16 reg; > + u16 devadr; > + > + if (miiphy_set_current_dev(name)) > + return; > + > + /* command to read PHY dev address */ > + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { > + printf("Err..%s could not read PHY dev address\n", > + __FUNCTION__); > + return; > + } > + > + /* > + * Enable RGMII delay on Tx and Rx for CPU port > + * Ref: sec 4.7.2 of chip datasheet > + */ > + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 2); > + miiphy_read(name, devadr, MV88E1121_MAC_CTRL2_REG, ®); > + reg |= (MV88E1121_RGMII_RXTM_CTRL | MV88E1121_RGMII_TXTM_CTRL); > + miiphy_write(name, devadr, MV88E1121_MAC_CTRL2_REG, reg); > + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 0); > + > + /* reset the phy */ > + miiphy_reset(name, devadr); > + > + printf("88E1116 Initialized on %s\n", name); Function name and print info are mismatching. > +} > + > +void reset_phy(void) > +{ > + /* configure and initialize both PHY's */ > + mv_phy_88e1121_init("egiga0"); > + mv_phy_88e1121_init("egiga1"); > +} > +#endif /* CONFIG_RESET_PHY_R */ > diff --git a/board/Marvell/dreamplug/dreamplug.h > b/board/Marvell/dreamplug/dreamplug.h > new file mode 100644 > index 0000000..21bf644 > --- /dev/null > +++ b/board/Marvell/dreamplug/dreamplug.h > @@ -0,0 +1,42 @@ > +/* > + * (C) Copyright 2011 > + * Jason Cooper <u-boot@lakedaemon.net> > + * > + * Based on work by: > + * Marvell Semiconductor <www.marvell.com> > + * Written-by: Siddarth Gore <gores@marvell.com> > + * > + * See file CREDITS for list of people who contributed to this > + * project. > + * > + * This program is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of > + * the License, or (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * You should have received a copy of the GNU General Public License > + * along with this program; if not, write to the Free Software > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > + * MA 02110-1301 USA > + */ > + > +#ifndef __DREAMPLUG_H > +#define __DREAMPLUG_H > + > +#define DREAMPLUG_OE_LOW (~(0)) > +#define DREAMPLUG_OE_HIGH (~(0)) > +#define DREAMPLUG_OE_VAL_LOW 0 > +#define DREAMPLUG_OE_VAL_HIGH (0xf << 16) /* 4 LED Pins high */ > + > +/* PHY related */ > +#define MV88E1121_MAC_CTRL2_REG 21 > +#define MV88E1121_PGADR_REG 22 > +#define MV88E1121_RGMII_TXTM_CTRL (1 << 4) > +#define MV88E1121_RGMII_RXTM_CTRL (1 << 5) > + > +#endif /* __DREAMPLUG_H */ > diff --git a/board/Marvell/dreamplug/kwbimage.cfg > b/board/Marvell/dreamplug/kwbimage.cfg I hope this is not same as guruplug (since you are using same machine-id)? > new file mode 100644 > index 0000000..ca9cd74 > --- /dev/null > +++ b/board/Marvell/dreamplug/kwbimage.cfg > @@ -0,0 +1,163 @@ > +# > +# (C) Copyright 2011 > +# Jason Cooper <u-boot@lakedaemon.net> > +# > +# Based on work by: > +# Marvell Semiconductor <www.marvell.com> > +# Written-by: Siddarth Gore <gores@marvell.com> > +# > +# See file CREDITS for list of people who contributed to this > +# project. > +# > +# This program is free software; you can redistribute it and/or > +# modify it under the terms of the GNU General Public License as > +# published by the Free Software Foundation; either version 2 of > +# the License, or (at your option) any later version. > +# > +# This program is distributed in the hope that it will be useful, > +# but WITHOUT ANY WARRANTY; without even the implied warranty of > +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > +# GNU General Public License for more details. > +# > +# You should have received a copy of the GNU General Public License > +# along with this program; if not, write to the Free Software > +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > +# MA 02110-1301 USA > +# > +# Refer docs/README.kwimage for more details about how-to configure > +# and create kirkwood boot image > +# > + > +# Boot Media configurations > +BOOT_FROM spi > + > +# SOC registers configuration using bootrom header extension > +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed > + > +# Configure RGMII-0/1 interface pad voltage to 1.8V > +DATA 0xFFD100e0 0x1b1b9b9b > + > +#Dram initalization for SINGLE x16 CL=5 @ 400MHz > +DATA 0xFFD01400 0x43000c30 # DDR Configuration register > +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) > +# bit23-14: zero > +# bit24: 1= enable exit self refresh mode on DDR access > +# bit25: 1 required > +# bit29-26: zero > +# bit31-30: 01 > + > +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low > +# bit 4: 0=addr/cmd in smame cycle > +# bit 5: 0=clk is driven during self refresh, we don't care for APX > +# bit 6: 0=use recommended falling edge of clk for addr/cmd > +# bit14: 0=input buffer always powered up > +# bit18: 1=cpu lock transaction enabled > +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled > bit31=0 > +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, > unbuffered DIMM > +# bit30-28: 3 required > +# bit31: 0=no additional STARTBURST delay > + > +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value > +1) > +# bit3-0: TRAS lsbs > +# bit7-4: TRCD > +# bit11- 8: TRP > +# bit15-12: TWR > +# bit19-16: TWTR > +# bit20: TRAS msb > +# bit23-21: 0x0 > +# bit27-24: TRRD > +# bit31-28: TRTP > + > +DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) > +# bit6-0: TRFC > +# bit8-7: TR2R > +# bit10-9: TR2W > +# bit12-11: TW2W > +# bit31-13: zero required > + > +DATA 0xFFD01410 0x000000cc # DDR Address Control > +# bit1-0: 01, Cs0width=x8 > +# bit3-2: 10, Cs0size=1Gb > +# bit5-4: 01, Cs1width=x8 > +# bit7-6: 10, Cs1size=1Gb > +# bit9-8: 00, Cs2width=nonexistent > +# bit11-10: 00, Cs2size =nonexistent > +# bit13-12: 00, Cs3width=nonexistent > +# bit15-14: 00, Cs3size =nonexistent > +# bit16: 0, Cs0AddrSel > +# bit17: 0, Cs1AddrSel > +# bit18: 0, Cs2AddrSel > +# bit19: 0, Cs3AddrSel > +# bit31-20: 0 required > + > +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control > +# bit0: 0, OpenPage enabled > +# bit31-1: 0 required > + > +DATA 0xFFD01418 0x00000000 # DDR Operation > +# bit3-0: 0x0, DDR cmd > +# bit31-4: 0 required > + > +DATA 0xFFD0141C 0x00000C52 # DDR Mode > +# bit2-0: 2, BurstLen=2 required > +# bit3: 0, BurstType=0 required > +# bit6-4: 4, CL=5 > +# bit7: 0, TestMode=0 normal > +# bit8: 0, DLL reset=0 normal > +# bit11-9: 6, auto-precharge write recovery ???????????? > +# bit12: 0, PD must be zero > +# bit31-13: 0 required > + > +DATA 0xFFD01420 0x00000040 # DDR Extended Mode > +# bit0: 0, DDR DLL enabled > +# bit1: 0, DDR drive strenght normal > +# bit2: 0, DDR ODT control lsd (disabled) > +# bit5-3: 000, required > +# bit6: 1, DDR ODT control msb, (disabled) > +# bit9-7: 000, required > +# bit10: 0, differential DQS enabled > +# bit11: 0, required > +# bit12: 0, DDR output buffer enabled > +# bit31-13: 0 required > + > +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High > +# bit2-0: 111, required > +# bit3 : 1 , MBUS Burst Chop disabled > +# bit6-4: 111, required > +# bit7 : 0 > +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= > 300MHz > +# bit9 : 0 , no half clock cycle addition to dataout > +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals > +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh > +# bit15-12: 1111 required > +# bit31-16: 0 required > + > +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) > +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) > + > +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 > +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size > +# bit0: 1, Window enabled > +# bit1: 0, Write Protect disabled > +# bit3-2: 00, CS0 hit selected > +# bit23-4: ones, required > +# bit31-24: 0x0F, Size (i.e. 256MB) > + > +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb > +DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 > + > +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled > +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled > + > +DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) > +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) > +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above > +# bit3-2: 01, ODT1 active NEVER! > +# bit31-4: zero, required > + > +DATA 0xFFD0149C 0x0000E803 # CPU ODT Control > +DATA 0xFFD01480 0x00000001 # DDR Initialization Control > +#bit0=1, enable DDR init upon this register write > + > +# End of Header extension > +DATA 0x0 0x0 > diff --git a/boards.cfg b/boards.cfg > index dfefc3f..294c675 100644 > --- a/boards.cfg > +++ b/boards.cfg > @@ -118,6 +118,7 @@ davinci_sonata arm arm926ejs > sonata davinci > suen3 arm arm926ejs km_arm > keymile kirkwood > suen8 arm arm926ejs km_arm > keymile kirkwood > mgcoge3un arm arm926ejs km_arm > keymile kirkwood > +dreamplug arm arm926ejs - > Marvell kirkwood > guruplug arm arm926ejs - > Marvell kirkwood > mv88f6281gtw_ge arm arm926ejs - > Marvell kirkwood > openrd_base arm arm926ejs openrd > Marvell kirkwood openrd:BOARD_IS_OPENRD_BASE > diff --git a/include/configs/dreamplug.h b/include/configs/dreamplug.h > new file mode 100644 > index 0000000..2a908f4 > --- /dev/null > +++ b/include/configs/dreamplug.h > @@ -0,0 +1,138 @@ > +/* > + * (C) Copyright 2011 > + * Jason Cooper <u-boot@lakedaemon.net> > + * > + * Based on work by: > + * Marvell Semiconductor <www.marvell.com> > + * Written-by: Siddarth Gore <gores@marvell.com> > + * > + * See file CREDITS for list of people who contributed to this > + * project. > + * > + * This program is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of > + * the License, or (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * You should have received a copy of the GNU General Public License > + * along with this program; if not, write to the Free Software > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > + * MA 02110-1301 USA > + */ > + > +#ifndef _CONFIG_DREAMPLUG_H > +#define _CONFIG_DREAMPLUG_H > + > +/* > + * Version number information > + */ > +#define CONFIG_IDENT_STRING "\nMarvell-DreamPlug" > + > +/* > + * High Level Configuration Options (easy to change) > + */ > +#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ > +#define CONFIG_KIRKWOOD 1 /* SOC Family Name */ > +#define CONFIG_KW88F6281 1 /* SOC Name */ > +#define CONFIG_MACH_GURUPLUG /* Machine type */ > +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ > + > +/* > + * Commands configuration > + */ > +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ > +#include <config_cmd_default.h> > +#define CONFIG_CMD_DHCP > +#define CONFIG_CMD_ENV > +#define CONFIG_CMD_FAT > +#define CONFIG_CMD_SF > +#define CONFIG_CMD_PING > +#define CONFIG_CMD_USB > +#define CONFIG_CMD_IDE > +#define CONFIG_CMD_DATE > + > +/* > + * mv-common.h should be defined after CMD configs since it used them > + * to enable certain macros > + */ > +#include "mv-common.h" > + > +/* > + * Environment variables configurations > + */ > +#ifdef CONFIG_SPI_FLASH > +#define CONFIG_ENV_IS_IN_SPI_FLASH 1 > +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64k */ > +#else > +#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ > +#endif > + > +#ifdef CONFIG_CMD_SF > +#define CONFIG_SPI_FLASH 1 > +#define CONFIG_HARD_SPI 1 > +#define CONFIG_KIRKWOOD_SPI 1 > +#define CONFIG_SPI_FLASH_MACRONIX 1 > +#define CONFIG_ENV_SPI_BUS 0 > +#define CONFIG_ENV_SPI_CS 0 > +#define CONFIG_ENV_SPI_MAX_HZ 50000000 /* 50 MHz */ > +#endif > + > +/* > + * max 4k env size is enough, but in case of nand > + * it has to be rounded to sector size > + */ > +#define CONFIG_ENV_SIZE 0x1000 /* 4k */ > +#define CONFIG_ENV_ADDR 0x100000 > +#define CONFIG_ENV_OFFSET 0x100000 /* env starts here */ > + > +/* > + * Default environment variables > + */ > +#define CONFIG_BOOTCOMMAND "setenv ethact egiga0; " \ > + "${x_bootcmd_ethernet}; setenv ethact egiga1; " \ > + "${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; "\ > + "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ > + "bootm 0x6400000;" > + > +#define CONFIG_EXTRA_ENV_SETTINGS \ > + "x_bootcmd_ethernet=ping 192.168.2.1\0" \ > + "x_bootcmd_usb=usb start\0" \ > + "x_bootcmd_kernel=fatload usb 0 0x6400000 uImage\0" \ > + "x_bootargs=console=ttyS0,115200\0" \ > + "x_bootargs_root=root=/dev/sda2 rootdelay=10\0" > + > +/* > + * Ethernet Driver configuration > + */ > +#ifdef CONFIG_CMD_NET > +#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ > +#define CONFIG_PHY_BASE_ADR 0 > +#endif /* CONFIG_CMD_NET */ > + > +/* > + * SATA Driver configuration > + */ > +#ifdef CONFIG_MVSATA_IDE > +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET > +#endif /*CONFIG_MVSATA_IDE*/ > + > +/* > + * RTC driver configuration > + */ > +#ifdef CONFIG_CMD_DATE > +#define CONFIG_RTC_MVINTEG > +#endif /* CONFIG_CMD_DATE */ > + > +#define CONFIG_SYS_ALT_MEMTEST > + > +/* > + * display enhanced info about the cpu at boot. > + */ > +#define CONFIG_DISPLAY_CPUINFO > + > +#endif /* _CONFIG_DREAMPLUG_H */ > -- Regards.. Prafulla . . > 1.7.0.4
On Wed, Jul 27, 2011 at 11:38:55AM -0700, Prafulla Wadaskar wrote: > > > > -----Original Message----- > > From: Jason Cooper [mailto:u-boot@lakedaemon.net] > > Sent: Wednesday, July 27, 2011 2:49 AM > > To: clint@debian.org; wd@denx.de; Prafulla Wadaskar > > Cc: u-boot@lists.denx.de; Prabhanjan Sarnaik; Ashish Karkare; Siddarth > > Gore; bdale@gag.com; Jason Cooper > > Subject: RFC [PATCH 4/5 v5] dreamplug: initial board support. > > > > Copied wholeheartedly from board/Marvell/guruplug and modified to add > > support > > for SPI NOR flash. > > > > Also, the following features are used: > > - Use the Marvell Integrated RTC. > > - display Marvell CPU/L2/etc speeds if requested. > > > > Note: this still uses MACH_TYPE_GURUPLUG until MACH_TYPE_DREAMPLUG is > > accepted > > into mainline Linux. The source from Globalscale did the same. > > > > Signed-off-by: Jason Cooper <u-boot@lakedaemon.net> > > --- > > There is no change log for all previous versions. > Please put them here. > Ref: http://www.denx.de/wiki/view/U-Boot/Patches#Sending_updated_patch_versions %$#%@#. I knew I forgot something. Here it is: Changes from v1 to v2: - resorted series to move 'make all' support last. Changes from v2 to v3: - Use MACH_TYPE_GURUPLUG for now until dreamplug support is in Linux. - Update MAINTAINERS. - Collapse into one patch. Changes from v3 to v4: - update copyright info as recommended by Prafulla Wadaskar. - maintain proper order in boards.cfg, MAINTAINERS, etc. - label MPP's - change back to MACH_TYPE_DREAMPLUG. This patch is just RFC until the Dreamplug is supported in Linux (and MACH_TYPE_ added). Changes from v4 to v5: - Complete rewrite due to receiving u-boot source indirectly from Global Scale Tech. - Added driver for integrated RTC. (thx GST!) - Added support for displaying CPU frequencies at boot. (thx GST!) - Adjust USB timeout to handle dreamplug EHCI chipset. - Cleaned up MPP registers based on Global Scale code. (thx GST!) - broke out MACH_TYPE_DREAMPLUG changes since it's going to be a while until the Linux arm tree gets sorted and accepts new boards again. Since all Dreamplugs currently on the market set r1 to MACH_TYPE_GURUPLUG, this allows the board to be added to u-boot while waiting for Linux mainline. Once it's in Linux mainline, then the last patch can be integrated to use MACH_TYPE_DREAMPLUG. > > MAINTAINERS | 4 + > > MAKEALL | 1 + > > board/Marvell/dreamplug/Makefile | 54 +++++++++++ > > board/Marvell/dreamplug/dreamplug.c | 157 > > ++++++++++++++++++++++++++++++++ > > board/Marvell/dreamplug/dreamplug.h | 42 +++++++++ > > board/Marvell/dreamplug/kwbimage.cfg | 163 > > ++++++++++++++++++++++++++++++++++ > > boards.cfg | 1 + > > include/configs/dreamplug.h | 138 > > ++++++++++++++++++++++++++++ > > 8 files changed, 560 insertions(+), 0 deletions(-) > > create mode 100644 board/Marvell/dreamplug/Makefile > > create mode 100644 board/Marvell/dreamplug/dreamplug.c > > create mode 100644 board/Marvell/dreamplug/dreamplug.h > > create mode 100644 board/Marvell/dreamplug/kwbimage.cfg > > create mode 100644 include/configs/dreamplug.h > > > > diff --git a/MAINTAINERS b/MAINTAINERS > > index 2bba7b4..9affbea 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -70,6 +70,10 @@ Conn Clark <clark@esteem.com> > > > > ESTEEM192E MPC8xx > > > > +Jason Cooper <u-boot@lakedaemon.net> > > + > > + dreamplug ARM926EJS (Kirkwood SoC) > > + > > Joe D'Abbraccio <ljd015@freescale.com> > > > > MPC837xERDB MPC837x > > diff --git a/MAKEALL b/MAKEALL > > index 51db13e..55a122f 100755 > > --- a/MAKEALL > > +++ b/MAKEALL > > @@ -335,6 +335,7 @@ LIST_ARM9=" \ > > cp966 \ > > da830evm \ > > da850evm \ > > + dreamplug \ > > edb9301 \ > > edb9302 \ > > edb9302a \ > > diff --git a/board/Marvell/dreamplug/Makefile > > b/board/Marvell/dreamplug/Makefile > > new file mode 100644 > > index 0000000..9ee5406 > > --- /dev/null > > +++ b/board/Marvell/dreamplug/Makefile > > @@ -0,0 +1,54 @@ > > +# > > +# (C) Copyright 2011 > > +# Jason Cooper <u-boot@lakedaemon.net> > > +# > > +# Based on work by: > > +# Marvell Semiconductor <www.marvell.com> > > +# Written-by: Siddarth Gore <gores@marvell.com> > > +# > > +# See file CREDITS for list of people who contributed to this > > +# project. > > +# > > +# This program is free software; you can redistribute it and/or > > +# modify it under the terms of the GNU General Public License as > > +# published by the Free Software Foundation; either version 2 of > > +# the License, or (at your option) any later version. > > +# > > +# This program is distributed in the hope that it will be useful, > > +# but WITHOUT ANY WARRANTY; without even the implied warranty of > > +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > +# GNU General Public License for more details. > > +# > > +# You should have received a copy of the GNU General Public License > > +# along with this program; if not, write to the Free Software > > +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > > +# MA 02110-1301 USA > > +# > > + > > +include $(TOPDIR)/config.mk > > + > > +LIB = $(obj)lib$(BOARD).o > > + > > +COBJS := dreamplug.o > > + > > +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) > > +OBJS := $(addprefix $(obj),$(COBJS)) > > +SOBJS := $(addprefix $(obj),$(SOBJS)) > > + > > +$(LIB): $(obj).depend $(OBJS) $(SOBJS) > > + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) > > + > > +clean: > > + rm -f $(SOBJS) $(OBJS) > > + > > +distclean: clean > > + rm -f $(LIB) core *.bak .depend > > + > > +####################################################################### > > ## > > + > > +# defines $(obj).depend target > > +include $(SRCTREE)/rules.mk > > + > > +sinclude $(obj).depend > > + > > +####################################################################### > > ## > > diff --git a/board/Marvell/dreamplug/dreamplug.c > > b/board/Marvell/dreamplug/dreamplug.c > > new file mode 100644 > > index 0000000..cdc094a > > --- /dev/null > > +++ b/board/Marvell/dreamplug/dreamplug.c > > @@ -0,0 +1,157 @@ > > +/* > > + * (C) Copyright 2011 > > + * Jason Cooper <u-boot@lakedaemon.net> > > + * > > + * Based on work by: > > + * Marvell Semiconductor <www.marvell.com> > > + * Written-by: Siddarth Gore <gores@marvell.com> > > + * > > + * See file CREDITS for list of people who contributed to this > > + * project. > > + * > > + * This program is free software; you can redistribute it and/or > > + * modify it under the terms of the GNU General Public License as > > + * published by the Free Software Foundation; either version 2 of > > + * the License, or (at your option) any later version. > > + * > > + * This program is distributed in the hope that it will be useful, > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > + * GNU General Public License for more details. > > + * > > + * You should have received a copy of the GNU General Public License > > + * along with this program; if not, write to the Free Software > > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > > + * MA 02110-1301 USA > > + */ > > + > > +#include <common.h> > > +#include <miiphy.h> > > +#include <asm/arch/kirkwood.h> > > +#include <asm/arch/mpp.h> > > +#include "dreamplug.h" > > + > > +DECLARE_GLOBAL_DATA_PTR; > > + > > +int board_early_init_f(void) > > +{ > > + /* > > + * default gpio configuration > > + * There are maximum 64 gpios controlled through 2 sets of registers > > + * the below configuration configures mainly initial LED status > > + */ > > + kw_config_gpio(DREAMPLUG_OE_VAL_LOW, > > + DREAMPLUG_OE_VAL_HIGH, > > + DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH); > > + > > + /* Multi-Purpose Pins Functionality configuration */ > > + u32 kwmpp_config[] = { > > + MPP0_SPI_SCn, /* SPI Flash */ > > + MPP1_SPI_MOSI, > > + MPP2_SPI_SCK, > > + MPP3_SPI_MISO, > > + MPP4_NF_IO6, > > + MPP5_NF_IO7, > > + MPP6_SYSRST_OUTn, > > + MPP7_GPO, > > + MPP8_TW_SDA, > > + MPP9_TW_SCK, > > + MPP10_UART0_TXD, /* Serial */ > > + MPP11_UART0_RXD, > > + MPP12_SD_CLK, /* SDIO Slot */ > > + MPP13_SD_CMD, > > + MPP14_SD_D0, > > + MPP15_SD_D1, > > + MPP16_SD_D2, > > + MPP17_SD_D3, > > + MPP18_NF_IO0, > > + MPP19_NF_IO1, > > + MPP20_GE1_0, /* Gigabit Ethernet */ > > + MPP21_GE1_1, > > + MPP22_GE1_2, > > + MPP23_GE1_3, > > + MPP24_GE1_4, > > + MPP25_GE1_5, > > + MPP26_GE1_6, > > + MPP27_GE1_7, > > + MPP28_GE1_8, > > + MPP29_GE1_9, > > + MPP30_GE1_10, > > + MPP31_GE1_11, > > + MPP32_GE1_12, > > + MPP33_GE1_13, > > + MPP34_GE1_14, > > + MPP35_GE1_15, > > + MPP36_GPIO, > > + MPP37_GPIO, > > + MPP38_GPIO, > > + MPP39_GPIO, > > + MPP40_TDM_SPI_SCK, > > + MPP41_TDM_SPI_MISO, > > + MPP42_TDM_SPI_MOSI, > > + MPP43_GPIO, > > + MPP44_GPIO, > > + MPP45_GPIO, > > + MPP46_GPIO, /* Wifi AP LED */ > > + MPP47_GPIO, > > + MPP48_GPIO, /* Wifi LED */ > > It is better if you can comment about rest other GPIOSs with their > assigned functionality. I filled in what I was comfortable labeling, anything else would be a guess on my part. This is a standard kirkwood configuration except for pins 0-3 and the LEDS (46,48). Should I add a comment to the same effect? > > + MPP49_GPIO, > > + 0 > > + }; > > + kirkwood_mpp_conf(kwmpp_config); > > + return 0; > > +} > > + > > +int board_init(void) > > +{ > > + /* > > + * arch number of board > > + * XXX: change to MACH_TYPE_DREAMPLUG once in Linux mainline. > > + */ > > + gd->bd->bi_arch_number = MACH_TYPE_GURUPLUG; > > I think this board should have some delta to guruplug? I think you > should have different machine ID here. See added changelog and patch 5 in the series. > BTW: what is delta w.r.to guruplug? Just 2MB SPI flash instead of 512MB NAND flash. It grabs the kernel/initrd from an internal microSD card attached via USB, instead of NAND flash. OS is on the same microSD card. The dreamplug kernel shipped with the device doesn't even see the SPI flash. I think it may be the exact same as the guruplug kernel, although I haven't done a rigorous check. It's built for MACH_TYPE_GURUPLUG, though. It has some bells and whistles, like audio in/out, SPDIF out. Nothing else really relevant to u-boot. > > + > > + /* adress of boot parameters */ > > + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; > > + > > + return 0; > > +} > > + > > +#ifdef CONFIG_RESET_PHY_R > > +void mv_phy_88e1121_init(char *name) > > +{ > > + u16 reg; > > + u16 devadr; > > + > > + if (miiphy_set_current_dev(name)) > > + return; > > + > > + /* command to read PHY dev address */ > > + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { > > + printf("Err..%s could not read PHY dev address\n", > > + __FUNCTION__); > > + return; > > + } > > + > > + /* > > + * Enable RGMII delay on Tx and Rx for CPU port > > + * Ref: sec 4.7.2 of chip datasheet > > + */ > > + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 2); > > + miiphy_read(name, devadr, MV88E1121_MAC_CTRL2_REG, ®); > > + reg |= (MV88E1121_RGMII_RXTM_CTRL | MV88E1121_RGMII_TXTM_CTRL); > > + miiphy_write(name, devadr, MV88E1121_MAC_CTRL2_REG, reg); > > + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 0); > > + > > + /* reset the phy */ > > + miiphy_reset(name, devadr); > > + > > + printf("88E1116 Initialized on %s\n", name); > > Function name and print info are mismatching. Gah! good catch. I just copied that printf over from the GST source code. I'll fix it up. > > +} > > + > > +void reset_phy(void) > > +{ > > + /* configure and initialize both PHY's */ > > + mv_phy_88e1121_init("egiga0"); > > + mv_phy_88e1121_init("egiga1"); > > +} > > +#endif /* CONFIG_RESET_PHY_R */ > > diff --git a/board/Marvell/dreamplug/dreamplug.h > > b/board/Marvell/dreamplug/dreamplug.h > > new file mode 100644 > > index 0000000..21bf644 > > --- /dev/null > > +++ b/board/Marvell/dreamplug/dreamplug.h > > @@ -0,0 +1,42 @@ > > +/* > > + * (C) Copyright 2011 > > + * Jason Cooper <u-boot@lakedaemon.net> > > + * > > + * Based on work by: > > + * Marvell Semiconductor <www.marvell.com> > > + * Written-by: Siddarth Gore <gores@marvell.com> > > + * > > + * See file CREDITS for list of people who contributed to this > > + * project. > > + * > > + * This program is free software; you can redistribute it and/or > > + * modify it under the terms of the GNU General Public License as > > + * published by the Free Software Foundation; either version 2 of > > + * the License, or (at your option) any later version. > > + * > > + * This program is distributed in the hope that it will be useful, > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > + * GNU General Public License for more details. > > + * > > + * You should have received a copy of the GNU General Public License > > + * along with this program; if not, write to the Free Software > > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > > + * MA 02110-1301 USA > > + */ > > + > > +#ifndef __DREAMPLUG_H > > +#define __DREAMPLUG_H > > + > > +#define DREAMPLUG_OE_LOW (~(0)) > > +#define DREAMPLUG_OE_HIGH (~(0)) > > +#define DREAMPLUG_OE_VAL_LOW 0 > > +#define DREAMPLUG_OE_VAL_HIGH (0xf << 16) /* 4 LED Pins high */ > > + > > +/* PHY related */ > > +#define MV88E1121_MAC_CTRL2_REG 21 > > +#define MV88E1121_PGADR_REG 22 > > +#define MV88E1121_RGMII_TXTM_CTRL (1 << 4) > > +#define MV88E1121_RGMII_RXTM_CTRL (1 << 5) > > + > > +#endif /* __DREAMPLUG_H */ > > diff --git a/board/Marvell/dreamplug/kwbimage.cfg > > b/board/Marvell/dreamplug/kwbimage.cfg > > I hope this is not same as guruplug (since you are using same machine-id)? Very similar, see above. thx, Jason.
> -----Original Message----- > From: Jason [mailto:u-boot@lakedaemon.net] > Sent: Thursday, July 28, 2011 7:33 AM > To: Prafulla Wadaskar > Cc: clint@debian.org; wd@denx.de; u-boot@lists.denx.de; Prabhanjan > Sarnaik; Ashish Karkare; Siddarth Gore; bdale@gag.com > Subject: Re: RFC [PATCH 4/5 v5] dreamplug: initial board support. > > On Wed, Jul 27, 2011 at 11:38:55AM -0700, Prafulla Wadaskar wrote: > > > > > > > -----Original Message----- > > > From: Jason Cooper [mailto:u-boot@lakedaemon.net] > > > Sent: Wednesday, July 27, 2011 2:49 AM > > > To: clint@debian.org; wd@denx.de; Prafulla Wadaskar > > > Cc: u-boot@lists.denx.de; Prabhanjan Sarnaik; Ashish Karkare; > Siddarth > > > Gore; bdale@gag.com; Jason Cooper > > > Subject: RFC [PATCH 4/5 v5] dreamplug: initial board support. > > > > > > Copied wholeheartedly from board/Marvell/guruplug and modified to > add > > > support > > > for SPI NOR flash. > > > > > > Also, the following features are used: > > > - Use the Marvell Integrated RTC. > > > - display Marvell CPU/L2/etc speeds if requested. > > > > > > Note: this still uses MACH_TYPE_GURUPLUG until MACH_TYPE_DREAMPLUG > is > > > accepted > > > into mainline Linux. The source from Globalscale did the same. > > > > > > Signed-off-by: Jason Cooper <u-boot@lakedaemon.net> > > > --- > > > > There is no change log for all previous versions. > > Please put them here. > > Ref: http://www.denx.de/wiki/view/U- > Boot/Patches#Sending_updated_patch_versions > > %$#%@#. I knew I forgot something. Here it is: > > Changes from v1 to v2: > > - resorted series to move 'make all' support last. > > Changes from v2 to v3: > > - Use MACH_TYPE_GURUPLUG for now until dreamplug support is in > Linux. > - Update MAINTAINERS. > - Collapse into one patch. > > Changes from v3 to v4: > > - update copyright info as recommended by Prafulla Wadaskar. > - maintain proper order in boards.cfg, MAINTAINERS, etc. > - label MPP's > - change back to MACH_TYPE_DREAMPLUG. This patch is just RFC > until the Dreamplug is supported in Linux (and MACH_TYPE_ > added). > > Changes from v4 to v5: > > - Complete rewrite due to receiving u-boot source indirectly > from Global Scale Tech. > - Added driver for integrated RTC. (thx GST!) > - Added support for displaying CPU frequencies at boot. (thx > GST!) > - Adjust USB timeout to handle dreamplug EHCI chipset. > - Cleaned up MPP registers based on Global Scale code. (thx > GST!) > - broke out MACH_TYPE_DREAMPLUG changes since it's going to be a > while until the Linux arm tree gets sorted and accepts new > boards again. Since all Dreamplugs currently on the market > set r1 to MACH_TYPE_GURUPLUG, this allows the board to be > added to u-boot while waiting for Linux mainline. Once it's > in Linux mainline, then the last patch can be integrated to > use > MACH_TYPE_DREAMPLUG. Please kindly repost with changelog. > > > > MAINTAINERS | 4 + > > > MAKEALL | 1 + > > > board/Marvell/dreamplug/Makefile | 54 +++++++++++ > > > board/Marvell/dreamplug/dreamplug.c | 157 > > > ++++++++++++++++++++++++++++++++ > > > board/Marvell/dreamplug/dreamplug.h | 42 +++++++++ > > > board/Marvell/dreamplug/kwbimage.cfg | 163 > > > ++++++++++++++++++++++++++++++++++ > > > boards.cfg | 1 + > > > include/configs/dreamplug.h | 138 > > > ++++++++++++++++++++++++++++ > > > 8 files changed, 560 insertions(+), 0 deletions(-) > > > create mode 100644 board/Marvell/dreamplug/Makefile > > > create mode 100644 board/Marvell/dreamplug/dreamplug.c > > > create mode 100644 board/Marvell/dreamplug/dreamplug.h > > > create mode 100644 board/Marvell/dreamplug/kwbimage.cfg > > > create mode 100644 include/configs/dreamplug.h > > > > > > diff --git a/MAINTAINERS b/MAINTAINERS > > > index 2bba7b4..9affbea 100644 > > > --- a/MAINTAINERS > > > +++ b/MAINTAINERS > > > @@ -70,6 +70,10 @@ Conn Clark <clark@esteem.com> > > > > > > ESTEEM192E MPC8xx > > > > > > +Jason Cooper <u-boot@lakedaemon.net> > > > + > > > + dreamplug ARM926EJS (Kirkwood SoC) > > > + > > > Joe D'Abbraccio <ljd015@freescale.com> > > > > > > MPC837xERDB MPC837x > > > diff --git a/MAKEALL b/MAKEALL > > > index 51db13e..55a122f 100755 > > > --- a/MAKEALL > > > +++ b/MAKEALL > > > @@ -335,6 +335,7 @@ LIST_ARM9=" \ > > > cp966 \ > > > da830evm \ > > > da850evm \ > > > + dreamplug \ > > > edb9301 \ > > > edb9302 \ > > > edb9302a \ > > > diff --git a/board/Marvell/dreamplug/Makefile > > > b/board/Marvell/dreamplug/Makefile > > > new file mode 100644 > > > index 0000000..9ee5406 > > > --- /dev/null > > > +++ b/board/Marvell/dreamplug/Makefile > > > @@ -0,0 +1,54 @@ > > > +# > > > +# (C) Copyright 2011 > > > +# Jason Cooper <u-boot@lakedaemon.net> > > > +# > > > +# Based on work by: > > > +# Marvell Semiconductor <www.marvell.com> > > > +# Written-by: Siddarth Gore <gores@marvell.com> > > > +# > > > +# See file CREDITS for list of people who contributed to this > > > +# project. > > > +# > > > +# This program is free software; you can redistribute it and/or > > > +# modify it under the terms of the GNU General Public License as > > > +# published by the Free Software Foundation; either version 2 of > > > +# the License, or (at your option) any later version. > > > +# > > > +# This program is distributed in the hope that it will be useful, > > > +# but WITHOUT ANY WARRANTY; without even the implied warranty of > > > +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See > the > > > +# GNU General Public License for more details. > > > +# > > > +# You should have received a copy of the GNU General Public License > > > +# along with this program; if not, write to the Free Software > > > +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > > > +# MA 02110-1301 USA > > > +# > > > + > > > +include $(TOPDIR)/config.mk > > > + > > > +LIB = $(obj)lib$(BOARD).o > > > + > > > +COBJS := dreamplug.o > > > + > > > +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) > > > +OBJS := $(addprefix $(obj),$(COBJS)) > > > +SOBJS := $(addprefix $(obj),$(SOBJS)) > > > + > > > +$(LIB): $(obj).depend $(OBJS) $(SOBJS) > > > + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) > > > + > > > +clean: > > > + rm -f $(SOBJS) $(OBJS) > > > + > > > +distclean: clean > > > + rm -f $(LIB) core *.bak .depend > > > + > > > > +####################################################################### > > > ## > > > + > > > +# defines $(obj).depend target > > > +include $(SRCTREE)/rules.mk > > > + > > > +sinclude $(obj).depend > > > + > > > > +####################################################################### > > > ## > > > diff --git a/board/Marvell/dreamplug/dreamplug.c > > > b/board/Marvell/dreamplug/dreamplug.c > > > new file mode 100644 > > > index 0000000..cdc094a > > > --- /dev/null > > > +++ b/board/Marvell/dreamplug/dreamplug.c > > > @@ -0,0 +1,157 @@ > > > +/* > > > + * (C) Copyright 2011 > > > + * Jason Cooper <u-boot@lakedaemon.net> > > > + * > > > + * Based on work by: > > > + * Marvell Semiconductor <www.marvell.com> > > > + * Written-by: Siddarth Gore <gores@marvell.com> > > > + * > > > + * See file CREDITS for list of people who contributed to this > > > + * project. > > > + * > > > + * This program is free software; you can redistribute it and/or > > > + * modify it under the terms of the GNU General Public License as > > > + * published by the Free Software Foundation; either version 2 of > > > + * the License, or (at your option) any later version. > > > + * > > > + * This program is distributed in the hope that it will be useful, > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > + * GNU General Public License for more details. > > > + * > > > + * You should have received a copy of the GNU General Public > License > > > + * along with this program; if not, write to the Free Software > > > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > > > + * MA 02110-1301 USA > > > + */ > > > + > > > +#include <common.h> > > > +#include <miiphy.h> > > > +#include <asm/arch/kirkwood.h> > > > +#include <asm/arch/mpp.h> > > > +#include "dreamplug.h" > > > + > > > +DECLARE_GLOBAL_DATA_PTR; > > > + > > > +int board_early_init_f(void) > > > +{ > > > + /* > > > + * default gpio configuration > > > + * There are maximum 64 gpios controlled through 2 sets of > registers > > > + * the below configuration configures mainly initial LED > status > > > + */ > > > + kw_config_gpio(DREAMPLUG_OE_VAL_LOW, > > > + DREAMPLUG_OE_VAL_HIGH, > > > + DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH); > > > + > > > + /* Multi-Purpose Pins Functionality configuration */ > > > + u32 kwmpp_config[] = { > > > + MPP0_SPI_SCn, /* SPI Flash */ > > > + MPP1_SPI_MOSI, > > > + MPP2_SPI_SCK, > > > + MPP3_SPI_MISO, > > > + MPP4_NF_IO6, > > > + MPP5_NF_IO7, > > > + MPP6_SYSRST_OUTn, > > > + MPP7_GPO, > > > + MPP8_TW_SDA, > > > + MPP9_TW_SCK, > > > + MPP10_UART0_TXD, /* Serial */ > > > + MPP11_UART0_RXD, > > > + MPP12_SD_CLK, /* SDIO Slot */ > > > + MPP13_SD_CMD, > > > + MPP14_SD_D0, > > > + MPP15_SD_D1, > > > + MPP16_SD_D2, > > > + MPP17_SD_D3, > > > + MPP18_NF_IO0, > > > + MPP19_NF_IO1, > > > + MPP20_GE1_0, /* Gigabit Ethernet */ > > > + MPP21_GE1_1, > > > + MPP22_GE1_2, > > > + MPP23_GE1_3, > > > + MPP24_GE1_4, > > > + MPP25_GE1_5, > > > + MPP26_GE1_6, > > > + MPP27_GE1_7, > > > + MPP28_GE1_8, > > > + MPP29_GE1_9, > > > + MPP30_GE1_10, > > > + MPP31_GE1_11, > > > + MPP32_GE1_12, > > > + MPP33_GE1_13, > > > + MPP34_GE1_14, > > > + MPP35_GE1_15, > > > + MPP36_GPIO, > > > + MPP37_GPIO, > > > + MPP38_GPIO, > > > + MPP39_GPIO, > > > + MPP40_TDM_SPI_SCK, > > > + MPP41_TDM_SPI_MISO, > > > + MPP42_TDM_SPI_MOSI, > > > + MPP43_GPIO, > > > + MPP44_GPIO, > > > + MPP45_GPIO, > > > + MPP46_GPIO, /* Wifi AP LED */ > > > + MPP47_GPIO, > > > + MPP48_GPIO, /* Wifi LED */ > > > > It is better if you can comment about rest other GPIOSs with their > > assigned functionality. > > I filled in what I was comfortable labeling, anything else would be a > guess on my part. This is a standard kirkwood configuration except for > pins 0-3 and the LEDS (46,48). Should I add a comment to the same > effect? My comment was for MPPXX_GPIOs, for rest other macros are enough to explain. > > > > + MPP49_GPIO, > > > + 0 > > > + }; > > > + kirkwood_mpp_conf(kwmpp_config); > > > + return 0; > > > +} > > > + > > > +int board_init(void) > > > +{ > > > + /* > > > + * arch number of board > > > + * XXX: change to MACH_TYPE_DREAMPLUG once in Linux mainline. > > > + */ > > > + gd->bd->bi_arch_number = MACH_TYPE_GURUPLUG; > > > > I think this board should have some delta to guruplug? I think you > > should have different machine ID here. > > See added changelog and patch 5 in the series. > > > BTW: what is delta w.r.to guruplug? > > Just 2MB SPI flash instead of 512MB NAND flash. It grabs the > kernel/initrd from an internal microSD card attached via USB, instead > of NAND flash. OS is on the same microSD card. > > The dreamplug kernel shipped with the device doesn't even see the SPI > flash. I think it may be the exact same as the guruplug kernel, > although I haven't done a rigorous check. It's built for > MACH_TYPE_GURUPLUG, though. > > It has some bells and whistles, like audio in/out, SPDIF out. Nothing > else really relevant to u-boot. > > > > + > > > + /* adress of boot parameters */ > > > + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; > > > + > > > + return 0; > > > +} > > > + > > > +#ifdef CONFIG_RESET_PHY_R > > > +void mv_phy_88e1121_init(char *name) > > > +{ > > > + u16 reg; > > > + u16 devadr; > > > + > > > + if (miiphy_set_current_dev(name)) > > > + return; > > > + > > > + /* command to read PHY dev address */ > > > + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { > > > + printf("Err..%s could not read PHY dev address\n", > > > + __FUNCTION__); > > > + return; > > > + } > > > + > > > + /* > > > + * Enable RGMII delay on Tx and Rx for CPU port > > > + * Ref: sec 4.7.2 of chip datasheet > > > + */ > > > + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 2); > > > + miiphy_read(name, devadr, MV88E1121_MAC_CTRL2_REG, ®); > > > + reg |= (MV88E1121_RGMII_RXTM_CTRL | > MV88E1121_RGMII_TXTM_CTRL); > > > + miiphy_write(name, devadr, MV88E1121_MAC_CTRL2_REG, reg); > > > + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 0); > > > + > > > + /* reset the phy */ > > > + miiphy_reset(name, devadr); > > > + > > > + printf("88E1116 Initialized on %s\n", name); > > > > Function name and print info are mismatching. > > Gah! good catch. I just copied that printf over from the GST source > code. I'll fix it up. > > > > +} > > > + > > > +void reset_phy(void) > > > +{ > > > + /* configure and initialize both PHY's */ > > > + mv_phy_88e1121_init("egiga0"); > > > + mv_phy_88e1121_init("egiga1"); > > > +} > > > +#endif /* CONFIG_RESET_PHY_R */ > > > diff --git a/board/Marvell/dreamplug/dreamplug.h > > > b/board/Marvell/dreamplug/dreamplug.h > > > new file mode 100644 > > > index 0000000..21bf644 > > > --- /dev/null > > > +++ b/board/Marvell/dreamplug/dreamplug.h > > > @@ -0,0 +1,42 @@ > > > +/* > > > + * (C) Copyright 2011 > > > + * Jason Cooper <u-boot@lakedaemon.net> > > > + * > > > + * Based on work by: > > > + * Marvell Semiconductor <www.marvell.com> > > > + * Written-by: Siddarth Gore <gores@marvell.com> > > > + * > > > + * See file CREDITS for list of people who contributed to this > > > + * project. > > > + * > > > + * This program is free software; you can redistribute it and/or > > > + * modify it under the terms of the GNU General Public License as > > > + * published by the Free Software Foundation; either version 2 of > > > + * the License, or (at your option) any later version. > > > + * > > > + * This program is distributed in the hope that it will be useful, > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > + * GNU General Public License for more details. > > > + * > > > + * You should have received a copy of the GNU General Public > License > > > + * along with this program; if not, write to the Free Software > > > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > > > + * MA 02110-1301 USA > > > + */ > > > + > > > +#ifndef __DREAMPLUG_H > > > +#define __DREAMPLUG_H > > > + > > > +#define DREAMPLUG_OE_LOW (~(0)) > > > +#define DREAMPLUG_OE_HIGH (~(0)) > > > +#define DREAMPLUG_OE_VAL_LOW 0 > > > +#define DREAMPLUG_OE_VAL_HIGH (0xf << 16) /* 4 LED Pins high > */ > > > + > > > +/* PHY related */ > > > +#define MV88E1121_MAC_CTRL2_REG 21 > > > +#define MV88E1121_PGADR_REG 22 > > > +#define MV88E1121_RGMII_TXTM_CTRL (1 << 4) > > > +#define MV88E1121_RGMII_RXTM_CTRL (1 << 5) > > > + > > > +#endif /* __DREAMPLUG_H */ > > > diff --git a/board/Marvell/dreamplug/kwbimage.cfg > > > b/board/Marvell/dreamplug/kwbimage.cfg > > > > I hope this is not same as guruplug (since you are using same machine- > id)? > > Very similar, see above. We can overrule this at this and can go ahead having dreamplug as new board support since we have valid machin_id for this board. Regards.. Prafulla . .
On Thu, Jul 28, 2011 at 12:37:32PM -0700, Prafulla Wadaskar wrote: > > > > -----Original Message----- > > From: Jason [mailto:u-boot@lakedaemon.net] > > Sent: Thursday, July 28, 2011 7:33 AM > > To: Prafulla Wadaskar > > Cc: clint@debian.org; wd@denx.de; u-boot@lists.denx.de; Prabhanjan > > Sarnaik; Ashish Karkare; Siddarth Gore; bdale@gag.com > > Subject: Re: RFC [PATCH 4/5 v5] dreamplug: initial board support. > > > > On Wed, Jul 27, 2011 at 11:38:55AM -0700, Prafulla Wadaskar wrote: > > > > > > > > > > -----Original Message----- > > > > From: Jason Cooper [mailto:u-boot@lakedaemon.net] > > > > Sent: Wednesday, July 27, 2011 2:49 AM > > > > To: clint@debian.org; wd@denx.de; Prafulla Wadaskar > > > > Cc: u-boot@lists.denx.de; Prabhanjan Sarnaik; Ashish Karkare; > > Siddarth > > > > Gore; bdale@gag.com; Jason Cooper > > > > Subject: RFC [PATCH 4/5 v5] dreamplug: initial board support. > > > > > > > > Copied wholeheartedly from board/Marvell/guruplug and modified to > > add > > > > support > > > > for SPI NOR flash. > > > > > > > > Also, the following features are used: > > > > - Use the Marvell Integrated RTC. > > > > - display Marvell CPU/L2/etc speeds if requested. > > > > > > > > Note: this still uses MACH_TYPE_GURUPLUG until MACH_TYPE_DREAMPLUG > > is > > > > accepted > > > > into mainline Linux. The source from Globalscale did the same. > > > > > > > > Signed-off-by: Jason Cooper <u-boot@lakedaemon.net> > > > > --- > > > > > > There is no change log for all previous versions. > > > Please put them here. > > > Ref: http://www.denx.de/wiki/view/U- > > Boot/Patches#Sending_updated_patch_versions > > > > %$#%@#. I knew I forgot something. Here it is: > > > > Changes from v1 to v2: > > > > - resorted series to move 'make all' support last. > > > > Changes from v2 to v3: > > > > - Use MACH_TYPE_GURUPLUG for now until dreamplug support is in > > Linux. > > - Update MAINTAINERS. > > - Collapse into one patch. > > > > Changes from v3 to v4: > > > > - update copyright info as recommended by Prafulla Wadaskar. > > - maintain proper order in boards.cfg, MAINTAINERS, etc. > > - label MPP's > > - change back to MACH_TYPE_DREAMPLUG. This patch is just RFC > > until the Dreamplug is supported in Linux (and MACH_TYPE_ > > added). > > > > Changes from v4 to v5: > > > > - Complete rewrite due to receiving u-boot source indirectly > > from Global Scale Tech. > > - Added driver for integrated RTC. (thx GST!) > > - Added support for displaying CPU frequencies at boot. (thx > > GST!) > > - Adjust USB timeout to handle dreamplug EHCI chipset. > > - Cleaned up MPP registers based on Global Scale code. (thx > > GST!) > > - broke out MACH_TYPE_DREAMPLUG changes since it's going to be a > > while until the Linux arm tree gets sorted and accepts new > > boards again. Since all Dreamplugs currently on the market > > set r1 to MACH_TYPE_GURUPLUG, this allows the board to be > > added to u-boot while waiting for Linux mainline. Once it's > > in Linux mainline, then the last patch can be integrated to > > use > > MACH_TYPE_DREAMPLUG. > > Please kindly repost with changelog. Will do. > > > > > > MAINTAINERS | 4 + > > > > MAKEALL | 1 + > > > > board/Marvell/dreamplug/Makefile | 54 +++++++++++ > > > > board/Marvell/dreamplug/dreamplug.c | 157 > > > > ++++++++++++++++++++++++++++++++ > > > > board/Marvell/dreamplug/dreamplug.h | 42 +++++++++ > > > > board/Marvell/dreamplug/kwbimage.cfg | 163 > > > > ++++++++++++++++++++++++++++++++++ > > > > boards.cfg | 1 + > > > > include/configs/dreamplug.h | 138 > > > > ++++++++++++++++++++++++++++ > > > > 8 files changed, 560 insertions(+), 0 deletions(-) > > > > create mode 100644 board/Marvell/dreamplug/Makefile > > > > create mode 100644 board/Marvell/dreamplug/dreamplug.c > > > > create mode 100644 board/Marvell/dreamplug/dreamplug.h > > > > create mode 100644 board/Marvell/dreamplug/kwbimage.cfg > > > > create mode 100644 include/configs/dreamplug.h > > > > > > > > diff --git a/MAINTAINERS b/MAINTAINERS > > > > index 2bba7b4..9affbea 100644 > > > > --- a/MAINTAINERS > > > > +++ b/MAINTAINERS > > > > @@ -70,6 +70,10 @@ Conn Clark <clark@esteem.com> > > > > > > > > ESTEEM192E MPC8xx > > > > > > > > +Jason Cooper <u-boot@lakedaemon.net> > > > > + > > > > + dreamplug ARM926EJS (Kirkwood SoC) > > > > + > > > > Joe D'Abbraccio <ljd015@freescale.com> > > > > > > > > MPC837xERDB MPC837x > > > > diff --git a/MAKEALL b/MAKEALL > > > > index 51db13e..55a122f 100755 > > > > --- a/MAKEALL > > > > +++ b/MAKEALL > > > > @@ -335,6 +335,7 @@ LIST_ARM9=" \ > > > > cp966 \ > > > > da830evm \ > > > > da850evm \ > > > > + dreamplug \ > > > > edb9301 \ > > > > edb9302 \ > > > > edb9302a \ > > > > diff --git a/board/Marvell/dreamplug/Makefile > > > > b/board/Marvell/dreamplug/Makefile > > > > new file mode 100644 > > > > index 0000000..9ee5406 > > > > --- /dev/null > > > > +++ b/board/Marvell/dreamplug/Makefile > > > > @@ -0,0 +1,54 @@ > > > > +# > > > > +# (C) Copyright 2011 > > > > +# Jason Cooper <u-boot@lakedaemon.net> > > > > +# > > > > +# Based on work by: > > > > +# Marvell Semiconductor <www.marvell.com> > > > > +# Written-by: Siddarth Gore <gores@marvell.com> > > > > +# > > > > +# See file CREDITS for list of people who contributed to this > > > > +# project. > > > > +# > > > > +# This program is free software; you can redistribute it and/or > > > > +# modify it under the terms of the GNU General Public License as > > > > +# published by the Free Software Foundation; either version 2 of > > > > +# the License, or (at your option) any later version. > > > > +# > > > > +# This program is distributed in the hope that it will be useful, > > > > +# but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See > > the > > > > +# GNU General Public License for more details. > > > > +# > > > > +# You should have received a copy of the GNU General Public License > > > > +# along with this program; if not, write to the Free Software > > > > +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > > > > +# MA 02110-1301 USA > > > > +# > > > > + > > > > +include $(TOPDIR)/config.mk > > > > + > > > > +LIB = $(obj)lib$(BOARD).o > > > > + > > > > +COBJS := dreamplug.o > > > > + > > > > +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) > > > > +OBJS := $(addprefix $(obj),$(COBJS)) > > > > +SOBJS := $(addprefix $(obj),$(SOBJS)) > > > > + > > > > +$(LIB): $(obj).depend $(OBJS) $(SOBJS) > > > > + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) > > > > + > > > > +clean: > > > > + rm -f $(SOBJS) $(OBJS) > > > > + > > > > +distclean: clean > > > > + rm -f $(LIB) core *.bak .depend > > > > + > > > > > > +####################################################################### > > > > ## > > > > + > > > > +# defines $(obj).depend target > > > > +include $(SRCTREE)/rules.mk > > > > + > > > > +sinclude $(obj).depend > > > > + > > > > > > +####################################################################### > > > > ## > > > > diff --git a/board/Marvell/dreamplug/dreamplug.c > > > > b/board/Marvell/dreamplug/dreamplug.c > > > > new file mode 100644 > > > > index 0000000..cdc094a > > > > --- /dev/null > > > > +++ b/board/Marvell/dreamplug/dreamplug.c > > > > @@ -0,0 +1,157 @@ > > > > +/* > > > > + * (C) Copyright 2011 > > > > + * Jason Cooper <u-boot@lakedaemon.net> > > > > + * > > > > + * Based on work by: > > > > + * Marvell Semiconductor <www.marvell.com> > > > > + * Written-by: Siddarth Gore <gores@marvell.com> > > > > + * > > > > + * See file CREDITS for list of people who contributed to this > > > > + * project. > > > > + * > > > > + * This program is free software; you can redistribute it and/or > > > > + * modify it under the terms of the GNU General Public License as > > > > + * published by the Free Software Foundation; either version 2 of > > > > + * the License, or (at your option) any later version. > > > > + * > > > > + * This program is distributed in the hope that it will be useful, > > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > > + * GNU General Public License for more details. > > > > + * > > > > + * You should have received a copy of the GNU General Public > > License > > > > + * along with this program; if not, write to the Free Software > > > > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > > > > + * MA 02110-1301 USA > > > > + */ > > > > + > > > > +#include <common.h> > > > > +#include <miiphy.h> > > > > +#include <asm/arch/kirkwood.h> > > > > +#include <asm/arch/mpp.h> > > > > +#include "dreamplug.h" > > > > + > > > > +DECLARE_GLOBAL_DATA_PTR; > > > > + > > > > +int board_early_init_f(void) > > > > +{ > > > > + /* > > > > + * default gpio configuration > > > > + * There are maximum 64 gpios controlled through 2 sets of > > registers > > > > + * the below configuration configures mainly initial LED > > status > > > > + */ > > > > + kw_config_gpio(DREAMPLUG_OE_VAL_LOW, > > > > + DREAMPLUG_OE_VAL_HIGH, > > > > + DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH); > > > > + > > > > + /* Multi-Purpose Pins Functionality configuration */ > > > > + u32 kwmpp_config[] = { > > > > + MPP0_SPI_SCn, /* SPI Flash */ > > > > + MPP1_SPI_MOSI, > > > > + MPP2_SPI_SCK, > > > > + MPP3_SPI_MISO, > > > > + MPP4_NF_IO6, > > > > + MPP5_NF_IO7, > > > > + MPP6_SYSRST_OUTn, > > > > + MPP7_GPO, > > > > + MPP8_TW_SDA, > > > > + MPP9_TW_SCK, > > > > + MPP10_UART0_TXD, /* Serial */ > > > > + MPP11_UART0_RXD, > > > > + MPP12_SD_CLK, /* SDIO Slot */ > > > > + MPP13_SD_CMD, > > > > + MPP14_SD_D0, > > > > + MPP15_SD_D1, > > > > + MPP16_SD_D2, > > > > + MPP17_SD_D3, > > > > + MPP18_NF_IO0, > > > > + MPP19_NF_IO1, > > > > + MPP20_GE1_0, /* Gigabit Ethernet */ > > > > + MPP21_GE1_1, > > > > + MPP22_GE1_2, > > > > + MPP23_GE1_3, > > > > + MPP24_GE1_4, > > > > + MPP25_GE1_5, > > > > + MPP26_GE1_6, > > > > + MPP27_GE1_7, > > > > + MPP28_GE1_8, > > > > + MPP29_GE1_9, > > > > + MPP30_GE1_10, > > > > + MPP31_GE1_11, > > > > + MPP32_GE1_12, > > > > + MPP33_GE1_13, > > > > + MPP34_GE1_14, > > > > + MPP35_GE1_15, > > > > + MPP36_GPIO, > > > > + MPP37_GPIO, > > > > + MPP38_GPIO, > > > > + MPP39_GPIO, > > > > + MPP40_TDM_SPI_SCK, > > > > + MPP41_TDM_SPI_MISO, > > > > + MPP42_TDM_SPI_MOSI, > > > > + MPP43_GPIO, > > > > + MPP44_GPIO, > > > > + MPP45_GPIO, > > > > + MPP46_GPIO, /* Wifi AP LED */ > > > > + MPP47_GPIO, > > > > + MPP48_GPIO, /* Wifi LED */ > > > > > > It is better if you can comment about rest other GPIOSs with their > > > assigned functionality. > > > > I filled in what I was comfortable labeling, anything else would be a > > guess on my part. This is a standard kirkwood configuration except for > > pins 0-3 and the LEDS (46,48). Should I add a comment to the same > > effect? > > My comment was for MPPXX_GPIOs, for rest other macros are enough to explain. Ahh, The Sheevaplug and the Guruplug had 7 GPIO pins exported to a header on the pcb. I haven't taken apart the dreamplug, but would assume it's the same. Especially since the Global Scale code didn't change it. MPP47 and MPP49 were LED pins on previous *plugs and appear not to be used in the dreamplug. I'll locate the header on the pcb and make a comment in the next version. If they are broken out, it would be nice to use the (proposed) gpio cmd on them from within uboot. > > > > + MPP49_GPIO, > > > > + 0 > > > > + }; > > > > + kirkwood_mpp_conf(kwmpp_config); > > > > + return 0; > > > > +} > > > > + > > > > +int board_init(void) > > > > +{ > > > > + /* > > > > + * arch number of board > > > > + * XXX: change to MACH_TYPE_DREAMPLUG once in Linux mainline. > > > > + */ > > > > + gd->bd->bi_arch_number = MACH_TYPE_GURUPLUG; > > > > > > I think this board should have some delta to guruplug? I think you > > > should have different machine ID here. > > > > See added changelog and patch 5 in the series. > > > > > BTW: what is delta w.r.to guruplug? > > > > Just 2MB SPI flash instead of 512MB NAND flash. It grabs the > > kernel/initrd from an internal microSD card attached via USB, instead > > of NAND flash. OS is on the same microSD card. > > > > The dreamplug kernel shipped with the device doesn't even see the SPI > > flash. I think it may be the exact same as the guruplug kernel, > > although I haven't done a rigorous check. It's built for > > MACH_TYPE_GURUPLUG, though. > > > > It has some bells and whistles, like audio in/out, SPDIF out. Nothing > > else really relevant to u-boot. > > > > > > + > > > > + /* adress of boot parameters */ > > > > + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +#ifdef CONFIG_RESET_PHY_R > > > > +void mv_phy_88e1121_init(char *name) > > > > +{ > > > > + u16 reg; > > > > + u16 devadr; > > > > + > > > > + if (miiphy_set_current_dev(name)) > > > > + return; > > > > + > > > > + /* command to read PHY dev address */ > > > > + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { > > > > + printf("Err..%s could not read PHY dev address\n", > > > > + __FUNCTION__); > > > > + return; > > > > + } > > > > + > > > > + /* > > > > + * Enable RGMII delay on Tx and Rx for CPU port > > > > + * Ref: sec 4.7.2 of chip datasheet > > > > + */ > > > > + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 2); > > > > + miiphy_read(name, devadr, MV88E1121_MAC_CTRL2_REG, ®); > > > > + reg |= (MV88E1121_RGMII_RXTM_CTRL | > > MV88E1121_RGMII_TXTM_CTRL); > > > > + miiphy_write(name, devadr, MV88E1121_MAC_CTRL2_REG, reg); > > > > + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 0); > > > > + > > > > + /* reset the phy */ > > > > + miiphy_reset(name, devadr); > > > > + > > > > + printf("88E1116 Initialized on %s\n", name); > > > > > > Function name and print info are mismatching. > > > > Gah! good catch. I just copied that printf over from the GST source > > code. I'll fix it up. > > > > > > +} > > > > + > > > > +void reset_phy(void) > > > > +{ > > > > + /* configure and initialize both PHY's */ > > > > + mv_phy_88e1121_init("egiga0"); > > > > + mv_phy_88e1121_init("egiga1"); > > > > +} > > > > +#endif /* CONFIG_RESET_PHY_R */ > > > > diff --git a/board/Marvell/dreamplug/dreamplug.h > > > > b/board/Marvell/dreamplug/dreamplug.h > > > > new file mode 100644 > > > > index 0000000..21bf644 > > > > --- /dev/null > > > > +++ b/board/Marvell/dreamplug/dreamplug.h > > > > @@ -0,0 +1,42 @@ > > > > +/* > > > > + * (C) Copyright 2011 > > > > + * Jason Cooper <u-boot@lakedaemon.net> > > > > + * > > > > + * Based on work by: > > > > + * Marvell Semiconductor <www.marvell.com> > > > > + * Written-by: Siddarth Gore <gores@marvell.com> > > > > + * > > > > + * See file CREDITS for list of people who contributed to this > > > > + * project. > > > > + * > > > > + * This program is free software; you can redistribute it and/or > > > > + * modify it under the terms of the GNU General Public License as > > > > + * published by the Free Software Foundation; either version 2 of > > > > + * the License, or (at your option) any later version. > > > > + * > > > > + * This program is distributed in the hope that it will be useful, > > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > > > + * GNU General Public License for more details. > > > > + * > > > > + * You should have received a copy of the GNU General Public > > License > > > > + * along with this program; if not, write to the Free Software > > > > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, > > > > + * MA 02110-1301 USA > > > > + */ > > > > + > > > > +#ifndef __DREAMPLUG_H > > > > +#define __DREAMPLUG_H > > > > + > > > > +#define DREAMPLUG_OE_LOW (~(0)) > > > > +#define DREAMPLUG_OE_HIGH (~(0)) > > > > +#define DREAMPLUG_OE_VAL_LOW 0 > > > > +#define DREAMPLUG_OE_VAL_HIGH (0xf << 16) /* 4 LED Pins high > > */ > > > > + > > > > +/* PHY related */ > > > > +#define MV88E1121_MAC_CTRL2_REG 21 > > > > +#define MV88E1121_PGADR_REG 22 > > > > +#define MV88E1121_RGMII_TXTM_CTRL (1 << 4) > > > > +#define MV88E1121_RGMII_RXTM_CTRL (1 << 5) > > > > + > > > > +#endif /* __DREAMPLUG_H */ > > > > diff --git a/board/Marvell/dreamplug/kwbimage.cfg > > > > b/board/Marvell/dreamplug/kwbimage.cfg > > > > > > I hope this is not same as guruplug (since you are using same machine- > > id)? > > > > Very similar, see above. > > We can overrule this at this and can go ahead having dreamplug as new > board support since we have valid machin_id for this board. Okay, I'll go dig up the patch for changing mach-types.h and include it in the next revision. thx, Jason.
> -----Original Message----- > From: Jason [mailto:u-boot@lakedaemon.net] > Sent: Friday, July 29, 2011 8:49 PM > To: Prafulla Wadaskar > Cc: clint@debian.org; wd@denx.de; u-boot@lists.denx.de; Prabhanjan > Sarnaik; Ashish Karkare; Siddarth Gore; bdale@gag.com > Subject: Re: RFC [PATCH 4/5 v5] dreamplug: initial board support. > ...snip... > > > > > + > > > > > +/* PHY related */ > > > > > +#define MV88E1121_MAC_CTRL2_REG 21 > > > > > +#define MV88E1121_PGADR_REG 22 > > > > > +#define MV88E1121_RGMII_TXTM_CTRL (1 << 4) > > > > > +#define MV88E1121_RGMII_RXTM_CTRL (1 << 5) > > > > > + > > > > > +#endif /* __DREAMPLUG_H */ > > > > > diff --git a/board/Marvell/dreamplug/kwbimage.cfg > > > > > b/board/Marvell/dreamplug/kwbimage.cfg > > > > > > > > I hope this is not same as guruplug (since you are using same > machine- > > > id)? > > > > > > Very similar, see above. > > > > We can overrule this at this and can go ahead having dreamplug as new > > board support since we have valid machin_id for this board. > > Okay, I'll go dig up the patch for changing mach-types.h and include it > in the next revision. As you said in other email, dreaplug used guruplug machine ID, this is wrong in principle. Changing machin-types.h is strictly not recommended, it will be NACked. So you have two options. 1. go and register new machin-id for dreamplug (if h/w delta is considerably high) 2. don't add dreamplug as separate board support, add it as new version for guruplug. Regards.. Prafulla . .
On Fri, Jul 29, 2011 at 11:57:46AM -0700, Prafulla Wadaskar wrote: > > > > -----Original Message----- > > From: Jason [mailto:u-boot@lakedaemon.net] > > Sent: Friday, July 29, 2011 8:49 PM > > To: Prafulla Wadaskar > > Cc: clint@debian.org; wd@denx.de; u-boot@lists.denx.de; Prabhanjan > > Sarnaik; Ashish Karkare; Siddarth Gore; bdale@gag.com > > Subject: Re: RFC [PATCH 4/5 v5] dreamplug: initial board support. > > > ...snip... > > > > > > + > > > > > > +/* PHY related */ > > > > > > +#define MV88E1121_MAC_CTRL2_REG 21 > > > > > > +#define MV88E1121_PGADR_REG 22 > > > > > > +#define MV88E1121_RGMII_TXTM_CTRL (1 << 4) > > > > > > +#define MV88E1121_RGMII_RXTM_CTRL (1 << 5) > > > > > > + > > > > > > +#endif /* __DREAMPLUG_H */ > > > > > > diff --git a/board/Marvell/dreamplug/kwbimage.cfg > > > > > > b/board/Marvell/dreamplug/kwbimage.cfg > > > > > > > > > > I hope this is not same as guruplug (since you are using same > > machine- > > > > id)? > > > > > > > > Very similar, see above. > > > > > > We can overrule this at this and can go ahead having dreamplug as new > > > board support since we have valid machin_id for this board. > > > > Okay, I'll go dig up the patch for changing mach-types.h and include it > > in the next revision. > > As you said in other email, dreaplug used guruplug machine ID, this is > wrong in principle. > > Changing machin-types.h is strictly not recommended, it will be > NACked. Right, this was my understanding. I must've misunderstood you. > So you have two options. > 1. go and register new machin-id for dreamplug (if h/w delta is > considerably high) Already did that a while ago. [1] The problem is, Linux controls mach-types.h and linux-arm isn't accepting new boards until they sort themselves out. Hence, why I was trying to establish a migration path. The Dreamplug *can* use a MACH_TYPE_GURUPLUG kernel (that's what it ships with), but Linux and userspace can't see the SPI flash in this configuration. In order to update uboot or to change uboot config userspace (eg debian) *must* be able to access the SPI flash. That's why I think the new machid is necessary. Distributions can carry the patches until mainline gets things sorted, so I'm not worried about that (other than the USB bug). I'm concerned about the folks who want to build a newer / custom uboot and put it on an existing system. They will most likely be using the kernel shipped with the Dreamplug, which is MACH_TYPE_GURUPLUG. Merging patches 1/5, 2/5, and 4/5 once in proper form, will allow users to do this. If the same user wants to access SPI flash from userspace, they can built a kernel.org kernel with my patches [2], and build uboot with patch 5/5 in my series to switch over to MACH_TYPE_DREAMPLUG. I know it's complicated, thanks for bearing with me. I haven't been able to find any recommendations by the linux-arm folks as far as what devs with new boards should be doing. I did just find [3] where Arnd Bergmann pushed a couple new boards upstream. I'll do some more research... thx, Jason. [1] http://www.arm.linux.org.uk/developer/machines/list.php?id=3550 *** Old version of patch! *** [2] https://patchwork.kernel.org/patch/879982/ [3] http://lkml.org/lkml/2011/7/26/430
Dear Jason Cooper, In message <1311715171-13128-4-git-send-email-u-boot@lakedaemon.net> you wrote: > Copied wholeheartedly from board/Marvell/guruplug and modified to add support > for SPI NOR flash. ... > + /* command to read PHY dev address */ > + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { > + printf("Err..%s could not read PHY dev address\n", > + __FUNCTION__); Checkpatch says: WARNING: __func__ should be used instead of gcc specific __FUNCTION__ Best regards, Wolfgang Denk
Wolfgang, On Thu, Oct 06, 2011 at 08:15:28PM +0200, Wolfgang Denk wrote: > In message <1311715171-13128-4-git-send-email-u-boot@lakedaemon.net> you wrote: > > Copied wholeheartedly from board/Marvell/guruplug and modified to add support > > for SPI NOR flash. > ... > > + /* command to read PHY dev address */ > > + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { > > + printf("Err..%s could not read PHY dev address\n", > > + __FUNCTION__); > > Checkpatch says: > > WARNING: __func__ should be used instead of gcc specific __FUNCTION__ This is an old version of this patch. v8 is currently in Prafulla's u-boot-marvell git tree. It's fixed in there. thx, Jason.
diff --git a/MAINTAINERS b/MAINTAINERS index 2bba7b4..9affbea 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -70,6 +70,10 @@ Conn Clark <clark@esteem.com> ESTEEM192E MPC8xx +Jason Cooper <u-boot@lakedaemon.net> + + dreamplug ARM926EJS (Kirkwood SoC) + Joe D'Abbraccio <ljd015@freescale.com> MPC837xERDB MPC837x diff --git a/MAKEALL b/MAKEALL index 51db13e..55a122f 100755 --- a/MAKEALL +++ b/MAKEALL @@ -335,6 +335,7 @@ LIST_ARM9=" \ cp966 \ da830evm \ da850evm \ + dreamplug \ edb9301 \ edb9302 \ edb9302a \ diff --git a/board/Marvell/dreamplug/Makefile b/board/Marvell/dreamplug/Makefile new file mode 100644 index 0000000..9ee5406 --- /dev/null +++ b/board/Marvell/dreamplug/Makefile @@ -0,0 +1,54 @@ +# +# (C) Copyright 2011 +# Jason Cooper <u-boot@lakedaemon.net> +# +# Based on work by: +# Marvell Semiconductor <www.marvell.com> +# Written-by: Siddarth Gore <gores@marvell.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := dreamplug.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/Marvell/dreamplug/dreamplug.c b/board/Marvell/dreamplug/dreamplug.c new file mode 100644 index 0000000..cdc094a --- /dev/null +++ b/board/Marvell/dreamplug/dreamplug.c @@ -0,0 +1,157 @@ +/* + * (C) Copyright 2011 + * Jason Cooper <u-boot@lakedaemon.net> + * + * Based on work by: + * Marvell Semiconductor <www.marvell.com> + * Written-by: Siddarth Gore <gores@marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <common.h> +#include <miiphy.h> +#include <asm/arch/kirkwood.h> +#include <asm/arch/mpp.h> +#include "dreamplug.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + kw_config_gpio(DREAMPLUG_OE_VAL_LOW, + DREAMPLUG_OE_VAL_HIGH, + DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + u32 kwmpp_config[] = { + MPP0_SPI_SCn, /* SPI Flash */ + MPP1_SPI_MOSI, + MPP2_SPI_SCK, + MPP3_SPI_MISO, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, /* Serial */ + MPP11_UART0_RXD, + MPP12_SD_CLK, /* SDIO Slot */ + MPP13_SD_CMD, + MPP14_SD_D0, + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GE1_0, /* Gigabit Ethernet */ + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GE1_8, + MPP29_GE1_9, + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GE1_14, + MPP35_GE1_15, + MPP36_GPIO, + MPP37_GPIO, + MPP38_GPIO, + MPP39_GPIO, + MPP40_TDM_SPI_SCK, + MPP41_TDM_SPI_MISO, + MPP42_TDM_SPI_MOSI, + MPP43_GPIO, + MPP44_GPIO, + MPP45_GPIO, + MPP46_GPIO, /* Wifi AP LED */ + MPP47_GPIO, + MPP48_GPIO, /* Wifi LED */ + MPP49_GPIO, + 0 + }; + kirkwood_mpp_conf(kwmpp_config); + return 0; +} + +int board_init(void) +{ + /* + * arch number of board + * XXX: change to MACH_TYPE_DREAMPLUG once in Linux mainline. + */ + gd->bd->bi_arch_number = MACH_TYPE_GURUPLUG; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; + + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +void mv_phy_88e1121_init(char *name) +{ + u16 reg; + u16 devadr; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { + printf("Err..%s could not read PHY dev address\n", + __FUNCTION__); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 2); + miiphy_read(name, devadr, MV88E1121_MAC_CTRL2_REG, ®); + reg |= (MV88E1121_RGMII_RXTM_CTRL | MV88E1121_RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MV88E1121_MAC_CTRL2_REG, reg); + miiphy_write(name, devadr, MV88E1121_PGADR_REG, 0); + + /* reset the phy */ + miiphy_reset(name, devadr); + + printf("88E1116 Initialized on %s\n", name); +} + +void reset_phy(void) +{ + /* configure and initialize both PHY's */ + mv_phy_88e1121_init("egiga0"); + mv_phy_88e1121_init("egiga1"); +} +#endif /* CONFIG_RESET_PHY_R */ diff --git a/board/Marvell/dreamplug/dreamplug.h b/board/Marvell/dreamplug/dreamplug.h new file mode 100644 index 0000000..21bf644 --- /dev/null +++ b/board/Marvell/dreamplug/dreamplug.h @@ -0,0 +1,42 @@ +/* + * (C) Copyright 2011 + * Jason Cooper <u-boot@lakedaemon.net> + * + * Based on work by: + * Marvell Semiconductor <www.marvell.com> + * Written-by: Siddarth Gore <gores@marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef __DREAMPLUG_H +#define __DREAMPLUG_H + +#define DREAMPLUG_OE_LOW (~(0)) +#define DREAMPLUG_OE_HIGH (~(0)) +#define DREAMPLUG_OE_VAL_LOW 0 +#define DREAMPLUG_OE_VAL_HIGH (0xf << 16) /* 4 LED Pins high */ + +/* PHY related */ +#define MV88E1121_MAC_CTRL2_REG 21 +#define MV88E1121_PGADR_REG 22 +#define MV88E1121_RGMII_TXTM_CTRL (1 << 4) +#define MV88E1121_RGMII_RXTM_CTRL (1 << 5) + +#endif /* __DREAMPLUG_H */ diff --git a/board/Marvell/dreamplug/kwbimage.cfg b/board/Marvell/dreamplug/kwbimage.cfg new file mode 100644 index 0000000..ca9cd74 --- /dev/null +++ b/board/Marvell/dreamplug/kwbimage.cfg @@ -0,0 +1,163 @@ +# +# (C) Copyright 2011 +# Jason Cooper <u-boot@lakedaemon.net> +# +# Based on work by: +# Marvell Semiconductor <www.marvell.com> +# Written-by: Siddarth Gore <gores@marvell.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0/1 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b9b9b + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000c30 # DDR Configuration register +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x000000cc # DDR Address Control +# bit1-0: 01, Cs0width=x8 +# bit3-2: 10, Cs0size=1Gb +# bit5-4: 01, Cs1width=x8 +# bit7-6: 10, Cs1size=1Gb +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000C52 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000040 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 0, DDR drive strenght normal +# bit2: 0, DDR ODT control lsd (disabled) +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, (disabled) +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb +DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 01, ODT1 active NEVER! +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000E803 # CPU ODT Control +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/boards.cfg b/boards.cfg index dfefc3f..294c675 100644 --- a/boards.cfg +++ b/boards.cfg @@ -118,6 +118,7 @@ davinci_sonata arm arm926ejs sonata davinci suen3 arm arm926ejs km_arm keymile kirkwood suen8 arm arm926ejs km_arm keymile kirkwood mgcoge3un arm arm926ejs km_arm keymile kirkwood +dreamplug arm arm926ejs - Marvell kirkwood guruplug arm arm926ejs - Marvell kirkwood mv88f6281gtw_ge arm arm926ejs - Marvell kirkwood openrd_base arm arm926ejs openrd Marvell kirkwood openrd:BOARD_IS_OPENRD_BASE diff --git a/include/configs/dreamplug.h b/include/configs/dreamplug.h new file mode 100644 index 0000000..2a908f4 --- /dev/null +++ b/include/configs/dreamplug.h @@ -0,0 +1,138 @@ +/* + * (C) Copyright 2011 + * Jason Cooper <u-boot@lakedaemon.net> + * + * Based on work by: + * Marvell Semiconductor <www.marvell.com> + * Written-by: Siddarth Gore <gores@marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _CONFIG_DREAMPLUG_H +#define _CONFIG_DREAMPLUG_H + +/* + * Version number information + */ +#define CONFIG_IDENT_STRING "\nMarvell-DreamPlug" + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ +#define CONFIG_KIRKWOOD 1 /* SOC Family Name */ +#define CONFIG_KW88F6281 1 /* SOC Name */ +#define CONFIG_MACH_GURUPLUG /* Machine type */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#include <config_cmd_default.h> +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ENV +#define CONFIG_CMD_FAT +#define CONFIG_CMD_SF +#define CONFIG_CMD_PING +#define CONFIG_CMD_USB +#define CONFIG_CMD_IDE +#define CONFIG_CMD_DATE + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* + * Environment variables configurations + */ +#ifdef CONFIG_SPI_FLASH +#define CONFIG_ENV_IS_IN_SPI_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64k */ +#else +#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ +#endif + +#ifdef CONFIG_CMD_SF +#define CONFIG_SPI_FLASH 1 +#define CONFIG_HARD_SPI 1 +#define CONFIG_KIRKWOOD_SPI 1 +#define CONFIG_SPI_FLASH_MACRONIX 1 +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 50000000 /* 50 MHz */ +#endif + +/* + * max 4k env size is enough, but in case of nand + * it has to be rounded to sector size + */ +#define CONFIG_ENV_SIZE 0x1000 /* 4k */ +#define CONFIG_ENV_ADDR 0x100000 +#define CONFIG_ENV_OFFSET 0x100000 /* env starts here */ + +/* + * Default environment variables + */ +#define CONFIG_BOOTCOMMAND "setenv ethact egiga0; " \ + "${x_bootcmd_ethernet}; setenv ethact egiga1; " \ + "${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; "\ + "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ + "bootm 0x6400000;" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "x_bootcmd_ethernet=ping 192.168.2.1\0" \ + "x_bootcmd_usb=usb start\0" \ + "x_bootcmd_kernel=fatload usb 0 0x6400000 uImage\0" \ + "x_bootargs=console=ttyS0,115200\0" \ + "x_bootargs_root=root=/dev/sda2 rootdelay=10\0" + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ +#define CONFIG_PHY_BASE_ADR 0 +#endif /* CONFIG_CMD_NET */ + +/* + * SATA Driver configuration + */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ + +/* + * RTC driver configuration + */ +#ifdef CONFIG_CMD_DATE +#define CONFIG_RTC_MVINTEG +#endif /* CONFIG_CMD_DATE */ + +#define CONFIG_SYS_ALT_MEMTEST + +/* + * display enhanced info about the cpu at boot. + */ +#define CONFIG_DISPLAY_CPUINFO + +#endif /* _CONFIG_DREAMPLUG_H */
Copied wholeheartedly from board/Marvell/guruplug and modified to add support for SPI NOR flash. Also, the following features are used: - Use the Marvell Integrated RTC. - display Marvell CPU/L2/etc speeds if requested. Note: this still uses MACH_TYPE_GURUPLUG until MACH_TYPE_DREAMPLUG is accepted into mainline Linux. The source from Globalscale did the same. Signed-off-by: Jason Cooper <u-boot@lakedaemon.net> --- MAINTAINERS | 4 + MAKEALL | 1 + board/Marvell/dreamplug/Makefile | 54 +++++++++++ board/Marvell/dreamplug/dreamplug.c | 157 ++++++++++++++++++++++++++++++++ board/Marvell/dreamplug/dreamplug.h | 42 +++++++++ board/Marvell/dreamplug/kwbimage.cfg | 163 ++++++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/dreamplug.h | 138 ++++++++++++++++++++++++++++ 8 files changed, 560 insertions(+), 0 deletions(-) create mode 100644 board/Marvell/dreamplug/Makefile create mode 100644 board/Marvell/dreamplug/dreamplug.c create mode 100644 board/Marvell/dreamplug/dreamplug.h create mode 100644 board/Marvell/dreamplug/kwbimage.cfg create mode 100644 include/configs/dreamplug.h