Message ID | 4E8621F5.9010409@aribaud.net |
---|---|
State | Accepted |
Headers | show |
Dear Albert ARIBAUD, In message <4E8621F5.9010409@aribaud.net> you wrote: > Hi Wolfgang, > > I have moved the contents of u-boot-arm/next to u-boot-arm/master, and > therefore... > > The following changes since commit 1d5e7fb403257d62f0f2419cb83fdf6b0f02f215: > > Prepare v2011.09 (2011-09-29 21:11:15 +0200) > > are available in the git repository at: > git://git.denx.de/u-boot-arm.git master > > Ajay Bhargav (5): > gpio: Add GPIO driver framework for Marvell SoCs > gpio: Add GPIO driver for Marvell SoC Armada100 > net: Adds Fast Ethernet Controller driver for Armada100 > Armada100: Enable Ethernet support for GplugD > Armada100: Enable 88E3015 PHY support for GplugD > > Aneesh V (1): > omap4: update maintainer for omap4 boards > > Balaji T K (2): > mmc: omap: enable high capacity > mmc: omap: config VMMC, MMC1_PBIAS > > Fabio Estevam (25): > ARM: mx25: Print the silicon revison > ARM: mx25: Print the source of reset > MX31: mx31pdk: Remove nand_spl config.mk file > MX31: Improve readability for reset cause > mx31pdk: Change the prompt as per other i.MX boards > MX25: tx25: Avoid the usage of extern in C file > MX25: Add initial support for MX25PDK > MX31: Disable watchdog during low-power modes > mx31pdk: Remove dram_init_banksize() > mx25pdk: Remove dram_init_banksize() > mx31ads: Remove dram_init_banksize() > imx31_litekit: Remove dram_init_banksize() > mx31pdk: Place machine ID into board config > mx25pdk: Place machine ID into board config > mx31ads: Place machine ID into board config > imx31_litekit: Place machine ID into board config > mx51evk: Place machine ID into board config > mx53loco: Place machine ID into board config > mx53smd: Place machine ID into board config > mx53ard: Place machine ID into board config > mx53evk: Place machine ID into board config > zmx25: Remove dram_init_banksize() > zmx25: Place machine ID into board config > zmx25: Fix build warning due to 'get_reset_cause' defined but not > used > vision2: Place machine ID into board config > > Heiko Schocher (16): > i2c, davinci: add i2c set speed > net, davinci_emac: add KSZ8864 switch > net, davinci_emac: make less verbose - turn printf() into debug() > net, davinci_emac: let the EMAC detect the PHYs > arm, davinci: move davinci_timer in header file > arm, davinci: add missing timer baseaddresses for !DA8xx cpu > arm, davinci: add internal WDT support for AM1808 cpus > arm, davinci: add RTC base addr > rtc, davinci: add support for davinci internal RTC > arm, davinci: add SYSCFG1 base and register struct > arm, davinci: add some missing defines in hardware.h > arm, davinci, am1808, gpio: add missing defines for bank 8 > arm, davinci: add ddr2 definition > arm, davinci: add NOR Boot Configuration Word > arm, davinci, am1808: add lowlevel functions for booting from NOR > arm, davinci, da8xx: add cpuinfo > > Jason Liu (1): > cosmetic: fsl_pmic: cosmetic for the help message > > Joe Hershberger (1): > omap4_panda: Ignore omap4 SPL called MLO > > Marek Vasut (19): > EfikaMX: Adjust undocumented magic constant in config file > FEC: Use proper accessor to read register in debug call > FEC: Use defined constant instead of magic number > FEC: Kill mode select FIXME's > FEC: Add RMII mode support > FEC: Allow selection of MII mode via CONFIG_FEC_XCV_TYPE > FEC: Abstract access to fec->eth in MII operations > FEC: Allow multiple FECes > FEC: Allow registering MII postconfiguration callback > FEC: Add timeout for chip reset > FEC: Squish "got MAC from fuse" message, make it debug() > FEC: Move imx_get_mac_from_fuse() definition to fec_mxc.h > MX5: Modify the PLL decoding algorithm > MX5: Add AHB clock reporting and fix IPG clock reporting > MX5: Clean up the output of "clocks" command > I2C: mxc_i2c rework > ATA: Squash warnings in mxc_ata. > EfikaMX: Add imximage config for Efika SB > EfikaSB: Add preliminary EfikaSB support > > Philip Balister (2): > OMAP3: Overo: Update GPMC timing for ethernet chip > overo: Set IEN on GPMC_CLK to support synchronous clocking. > > Sandeep Paulraj (1): > devkit8000: Fix build break > > Sanjeev Premi (2): > omap3: Fix compile warning > omap3evm: env: Fix default console > > Simon Schwarz (9): > omap-common/omap4: relocate early UART clock setup > omap3: Configure RAM bank 0 if in SPL > omap-common: add nand spl support > spl: add NAND Library to new SPL > spl: Add POWER library to new spl > omap3: new SPL structure support > devkit8000: Add nand-spl support for new SPL > omap3: implement boot parameter saving > omap-common: reorganize spl.c > > Thomas Weber (1): > Devkit8000: Change console from ttyS2 to ttyO2 > > .gitignore | 1 + > MAINTAINERS | 9 +- > arch/arm/cpu/arm1136/mx31/generic.c | 2 +- > arch/arm/cpu/arm1136/mx31/timer.c | 4 +- > arch/arm/cpu/arm926ejs/davinci/Makefile | 3 +- > arch/arm/cpu/arm926ejs/davinci/am1808_lowlevel.c | 428 ++++++++++++ > arch/arm/cpu/arm926ejs/davinci/cpu.c | 16 +- > arch/arm/cpu/arm926ejs/davinci/ksz8873.c | 68 ++ > arch/arm/cpu/arm926ejs/davinci/timer.c | 46 +- > arch/arm/cpu/arm926ejs/mx25/generic.c | 53 ++- > arch/arm/cpu/arm926ejs/start.S | 9 + > arch/arm/cpu/armv7/mx5/clock.c | 114 +++- > arch/arm/cpu/armv7/omap-common/Makefile | 6 + > arch/arm/cpu/armv7/omap-common/spl.c | 165 +---- > arch/arm/cpu/armv7/omap-common/spl_mmc.c | 150 ++++ > arch/arm/cpu/armv7/omap-common/spl_nand.c | 71 ++ > arch/arm/cpu/armv7/omap3/board.c | 50 ++- > arch/arm/cpu/armv7/omap3/config.mk | 30 + > arch/arm/cpu/armv7/omap3/lowlevel_init.S | 10 + > arch/arm/cpu/armv7/omap3/sdrc.c | 32 +- > arch/arm/cpu/armv7/omap3/sys_info.c | 2 +- > arch/arm/cpu/armv7/omap4/board.c | 1 + > arch/arm/include/asm/arch-armada100/armada100.h | 58 ++ > arch/arm/include/asm/arch-armada100/gpio.h | 48 ++ > arch/arm/include/asm/arch-armada100/mfp.h | 19 + > .../arm/include/asm/arch-davinci/am1808_lowlevel.h | 44 ++ > arch/arm/include/asm/arch-davinci/ddr2_defs.h | 96 +++ > arch/arm/include/asm/arch-davinci/emac_defs.h | 6 + > arch/arm/include/asm/arch-davinci/gpio.h | 2 + > arch/arm/include/asm/arch-davinci/hardware.h | 30 + > arch/arm/include/asm/arch-davinci/timer_defs.h | 44 ++ > arch/arm/include/asm/arch-mx25/imx-regs.h | 4 +- > arch/arm/include/asm/arch-mx25/sys_proto.h | 29 + > arch/arm/include/asm/arch-mx27/imx-regs.h | 1 - > arch/arm/include/asm/arch-mx31/imx-regs.h | 2 + > arch/arm/include/asm/arch-mx35/imx-regs.h | 2 - > arch/arm/include/asm/arch-mx5/crm_regs.h | 11 + > arch/arm/include/asm/arch-mx5/imx-regs.h | 5 +- > arch/arm/include/asm/arch-omap3/mem.h | 36 + > arch/arm/include/asm/arch-omap3/omap_gpmc.h | 9 + > arch/arm/include/asm/arch-omap3/sys_proto.h | 1 + > arch/arm/include/asm/arch-omap4/omap4.h | 8 +- > arch/arm/include/asm/omap_common.h | 31 + > board/Marvell/gplugd/gplugd.c | 71 ++ > board/efikamx/efikamx.c | 124 +++- > board/efikamx/{imximage.cfg => imximage_mx.cfg} | 0 > board/efikamx/{imximage.cfg => imximage_sb.cfg} | 26 +- > board/freescale/mx25pdk/Makefile | 49 ++ > board/freescale/mx25pdk/imximage.cfg | 73 ++ > board/freescale/mx25pdk/lowlevel_init.S | 21 + > board/freescale/mx25pdk/mx25pdk.c | 56 ++ > board/freescale/mx31ads/mx31ads.c | 7 - > board/freescale/mx31pdk/mx31pdk.c | 7 - > board/freescale/mx51evk/mx51evk.c | 1 - > board/freescale/mx53ard/mx53ard.c | 1 - > board/freescale/mx53evk/mx53evk.c | 1 - > board/freescale/mx53loco/mx53loco.c | 1 - > board/freescale/mx53smd/mx53smd.c | 1 - > board/isee/igep0020/igep0020.c | 1 + > board/isee/igep0020/igep0020.h | 9 - > board/karo/tx25/tx25.c | 3 +- > board/logicpd/imx31_litekit/imx31_litekit.c | 7 - > board/overo/overo.c | 1 + > board/overo/overo.h | 11 +- > board/syteco/zmx25/zmx25.c | 8 - > board/timll/devkit8000/devkit8000.c | 2 +- > board/ttcontrol/vision2/vision2.c | 1 - > boards.cfg | 5 +- > doc/README.SPL | 2 + > doc/README.davinci | 9 + > drivers/block/mxc_ata.c | 22 +- > drivers/gpio/Makefile | 1 + > drivers/gpio/mvgpio.c | 115 +++ > drivers/gpio/mvgpio.h | 74 ++ > drivers/i2c/davinci_i2c.c | 5 + > drivers/i2c/mxc_i2c.c | 422 ++++++++---- > drivers/misc/fsl_pmic.c | 2 +- > drivers/mmc/omap_hsmmc.c | 34 +- > drivers/mtd/nand/Makefile | 10 +- > drivers/mtd/nand/nand_base.c | 4 +- > drivers/mtd/nand/nand_spl_simple.c | 245 +++++++ > drivers/mtd/nand/omap_gpmc.c | 27 + > drivers/net/Makefile | 1 + > drivers/net/armada100_fec.c | 736 > ++++++++++++++++++++ > drivers/net/armada100_fec.h | 232 ++++++ > drivers/net/davinci_emac.c | 12 +- > drivers/net/fec_mxc.c | 170 +++-- > drivers/net/fec_mxc.h | 9 +- > drivers/power/twl6030.c | 7 + > drivers/rtc/Makefile | 1 + > drivers/rtc/davinci.c | 125 ++++ > include/configs/devkit8000.h | 48 ++- > include/configs/efikamx.h | 6 +- > include/configs/gplugd.h | 30 +- > include/configs/imx31_litekit.h | 4 +- > include/configs/mx25pdk.h | 108 +++ > include/configs/mx31ads.h | 2 + > include/configs/mx31pdk.h | 4 +- > include/configs/mx51evk.h | 1 + > include/configs/mx53ard.h | 2 + > include/configs/mx53evk.h | 2 + > include/configs/mx53loco.h | 2 + > include/configs/mx53smd.h | 4 +- > include/configs/omap3_evm.h | 2 +- > include/configs/omap4_common.h | 2 + > include/configs/omap4_sdp4430.h | 2 + > include/configs/vision2.h | 2 + > include/configs/zmx25.h | 1 + > include/nand.h | 6 + > include/netdev.h | 8 +- > include/twl6030.h | 3 + > nand_spl/board/freescale/mx31pdk/Makefile | 2 +- > nand_spl/board/freescale/mx31pdk/config.mk | 1 - > spl/Makefile | 2 + > 114 files changed, 4237 insertions(+), 515 deletions(-) > create mode 100644 arch/arm/cpu/arm926ejs/davinci/am1808_lowlevel.c > create mode 100644 arch/arm/cpu/arm926ejs/davinci/ksz8873.c > create mode 100644 arch/arm/cpu/armv7/omap-common/spl_mmc.c > create mode 100644 arch/arm/cpu/armv7/omap-common/spl_nand.c > create mode 100644 arch/arm/cpu/armv7/omap3/config.mk > create mode 100644 arch/arm/include/asm/arch-armada100/gpio.h > create mode 100644 arch/arm/include/asm/arch-davinci/am1808_lowlevel.h > create mode 100644 arch/arm/include/asm/arch-davinci/ddr2_defs.h > create mode 100644 arch/arm/include/asm/arch-davinci/timer_defs.h > create mode 100644 arch/arm/include/asm/arch-mx25/sys_proto.h > copy board/efikamx/{imximage.cfg => imximage_mx.cfg} (100%) > rename board/efikamx/{imximage.cfg => imximage_sb.cfg} (90%) > create mode 100644 board/freescale/mx25pdk/Makefile > create mode 100644 board/freescale/mx25pdk/imximage.cfg > create mode 100644 board/freescale/mx25pdk/lowlevel_init.S > create mode 100644 board/freescale/mx25pdk/mx25pdk.c > create mode 100644 drivers/gpio/mvgpio.c > create mode 100644 drivers/gpio/mvgpio.h > create mode 100644 drivers/mtd/nand/nand_spl_simple.c > create mode 100644 drivers/net/armada100_fec.c > create mode 100644 drivers/net/armada100_fec.h > create mode 100644 drivers/rtc/davinci.c > create mode 100644 include/configs/mx25pdk.h > delete mode 100644 nand_spl/board/freescale/mx31pdk/config.mk Applied, thanks. Best regards, Wolfgang Denk
Hi Albert, On Fri, Sep 30, 2011 at 1:09 PM, Albert ARIBAUD <albert.u.boot@aribaud.net> wrote: > Hi Wolfgang, > > I have moved the contents of u-boot-arm/next to u-boot-arm/master, and > therefore... Are you able to pick my the tegra clock/pinmux patch set as discussed please? I will get started on the next series. Regards, Simon > > The following changes since commit 1d5e7fb403257d62f0f2419cb83fdf6b0f02f215:
Hi Simon, Le 04/10/2011 07:35, Simon Glass a écrit : > Hi Albert, > > On Fri, Sep 30, 2011 at 1:09 PM, Albert ARIBAUD > <albert.u.boot@aribaud.net> wrote: >> Hi Wolfgang, >> >> I have moved the contents of u-boot-arm/next to u-boot-arm/master, and >> therefore... > > Are you able to pick my the tegra clock/pinmux patch set as discussed > please? I will get started on the next series. > > Regards, > Simon > >> >> The following changes since commit 1d5e7fb403257d62f0f2419cb83fdf6b0f02f215: FYI, these should all be in the current u-boot-arm/master. Let me know if anything is missing. Amicalement,
Hi Albert, On Fri, Oct 21, 2011 at 11:44 AM, Albert ARIBAUD <albert.u.boot@aribaud.net> wrote: > Hi Simon, > > Le 04/10/2011 07:35, Simon Glass a écrit : >> >> Hi Albert, >> >> On Fri, Sep 30, 2011 at 1:09 PM, Albert ARIBAUD >> <albert.u.boot@aribaud.net> wrote: >>> >>> Hi Wolfgang, >>> >>> I have moved the contents of u-boot-arm/next to u-boot-arm/master, and >>> therefore... >> >> Are you able to pick my the tegra clock/pinmux patch set as discussed >> please? I will get started on the next series. >> >> Regards, >> Simon >> >>> >>> The following changes since commit >>> 1d5e7fb403257d62f0f2419cb83fdf6b0f02f215: > > FYI, these should all be in the current u-boot-arm/master. Let me know if > anything is missing. Yes I see them, and have been basing off these recently, thank you. Please also see my other email about Stephen Warren's new changes, which are the next lot to go in. Regards, Simon > > Amicalement, > -- > Albert. >