| Message ID | 1315335696-20499-4-git-send-email-rogerio.pimentel@freescale.com |
|---|---|
| State | New |
| Headers | show |
On Tue, Sep 06, 2011 at 04:01:36PM -0300, Rogerio Pimentel wrote: > Adding flexcan support on i.MX53 ARD > > Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com> > --- > arch/arm/mach-mx5/Kconfig | 1 + > arch/arm/mach-mx5/board-mx53_ard.c | 21 +++++++++++++++++++++ > 2 files changed, 22 insertions(+), 0 deletions(-) > > diff --git a/arch/arm/mach-mx5/Kconfig b/arch/arm/mach-mx5/Kconfig > index fb4c503..7c911d1 100644 > --- a/arch/arm/mach-mx5/Kconfig > +++ b/arch/arm/mach-mx5/Kconfig > @@ -205,6 +205,7 @@ config MACH_MX53_LOCO > config MACH_MX53_ARD > bool "Support MX53 ARD platforms" > select SOC_IMX53 > + select IMX_HAVE_PLATFORM_FLEXCAN > select IMX_HAVE_PLATFORM_IMX2_WDT > select IMX_HAVE_PLATFORM_IMX_I2C > select IMX_HAVE_PLATFORM_IMX_UART > diff --git a/arch/arm/mach-mx5/board-mx53_ard.c b/arch/arm/mach-mx5/board-mx53_ard.c > index 76a67c4..e5f174b 100644 > --- a/arch/arm/mach-mx5/board-mx53_ard.c > +++ b/arch/arm/mach-mx5/board-mx53_ard.c > @@ -44,6 +44,8 @@ > #define ARD_BACK IMX_GPIO_NR(5, 11) > #define ARD_PROG IMX_GPIO_NR(5, 12) > #define ARD_VOLUMEUP IMX_GPIO_NR(5, 13) > +#define ARD_CAN_EN IMX_GPIO_NR(7, 6) > +#define ARD_CAN_STBY IMX_GPIO_NR(4, 15) > > static iomux_v3_cfg_t mx53_ard_pads[] = { > /* UART1 */ > @@ -102,6 +104,13 @@ static iomux_v3_cfg_t mx53_ard_pads[] = { > MX53_PAD_DISP0_DAT18__GPIO5_12, /* prog */ > MX53_PAD_DISP0_DAT19__GPIO5_13, /* vol up */ > MX53_PAD_GPIO_10__GPIO4_0, /* vol down */ > + /* CAN */ > + MX53_PAD_KEY_COL2__CAN1_TXCAN, > + MX53_PAD_KEY_ROW2__CAN1_RXCAN, > + MX53_PAD_PATA_RESET_B__CAN2_TXCAN, > + MX53_PAD_PATA_IORDY__CAN2_RXCAN, > + MX53_PAD_PATA_DA_0__GPIO7_6, > + MX53_PAD_KEY_ROW4__GPIO4_15, > }; > > #define GPIO_BUTTON(gpio_num, ev_code, act_low, descr, wake) \ > @@ -171,6 +180,8 @@ static struct imxi2c_platform_data mx53_ard_i2c3_data = { > > static void __init mx53_ard_io_init(void) > { > + int ret; > + > mxc_iomux_v3_setup_multiple_pads(mx53_ard_pads, > ARRAY_SIZE(mx53_ard_pads)); > > @@ -179,6 +190,14 @@ static void __init mx53_ard_io_init(void) > > gpio_request(ARD_I2CPORTEXP_B, "i2cptexp-rst"); > gpio_direction_output(ARD_I2CPORTEXP_B, 1); > + > + ret = gpio_request_one(ARD_CAN_EN, GPIOF_OUT_INIT_HIGH, "can-en"); > + if (ret) > + pr_err("Cannot request ARD_CAN_EN pin: %d\n", ret); > + > + ret = gpio_request_one(ARD_CAN_STBY, GPIOF_OUT_INIT_HIGH, "can-stby"); > + if (ret) > + pr_err("Cannot request ARD_CAN_STBY pin: %d\n", ret); > } > > /* Config CS1 settings for ethernet controller */ > @@ -234,6 +253,8 @@ static void __init mx53_ard_board_init(void) > imx53_add_imx_i2c(1, &mx53_ard_i2c2_data); > imx53_add_imx_i2c(2, &mx53_ard_i2c3_data); > imx_add_gpio_keys(&ard_button_data); > + imx53_add_flexcan0(NULL); > + imx53_add_flexcan1(NULL); If gpio_request_one above fails, do you really want to add the devices then? Best regards Uwe
diff --git a/arch/arm/mach-mx5/Kconfig b/arch/arm/mach-mx5/Kconfig index fb4c503..7c911d1 100644 --- a/arch/arm/mach-mx5/Kconfig +++ b/arch/arm/mach-mx5/Kconfig @@ -205,6 +205,7 @@ config MACH_MX53_LOCO config MACH_MX53_ARD bool "Support MX53 ARD platforms" select SOC_IMX53 + select IMX_HAVE_PLATFORM_FLEXCAN select IMX_HAVE_PLATFORM_IMX2_WDT select IMX_HAVE_PLATFORM_IMX_I2C select IMX_HAVE_PLATFORM_IMX_UART diff --git a/arch/arm/mach-mx5/board-mx53_ard.c b/arch/arm/mach-mx5/board-mx53_ard.c index 76a67c4..e5f174b 100644 --- a/arch/arm/mach-mx5/board-mx53_ard.c +++ b/arch/arm/mach-mx5/board-mx53_ard.c @@ -44,6 +44,8 @@ #define ARD_BACK IMX_GPIO_NR(5, 11) #define ARD_PROG IMX_GPIO_NR(5, 12) #define ARD_VOLUMEUP IMX_GPIO_NR(5, 13) +#define ARD_CAN_EN IMX_GPIO_NR(7, 6) +#define ARD_CAN_STBY IMX_GPIO_NR(4, 15) static iomux_v3_cfg_t mx53_ard_pads[] = { /* UART1 */ @@ -102,6 +104,13 @@ static iomux_v3_cfg_t mx53_ard_pads[] = { MX53_PAD_DISP0_DAT18__GPIO5_12, /* prog */ MX53_PAD_DISP0_DAT19__GPIO5_13, /* vol up */ MX53_PAD_GPIO_10__GPIO4_0, /* vol down */ + /* CAN */ + MX53_PAD_KEY_COL2__CAN1_TXCAN, + MX53_PAD_KEY_ROW2__CAN1_RXCAN, + MX53_PAD_PATA_RESET_B__CAN2_TXCAN, + MX53_PAD_PATA_IORDY__CAN2_RXCAN, + MX53_PAD_PATA_DA_0__GPIO7_6, + MX53_PAD_KEY_ROW4__GPIO4_15, }; #define GPIO_BUTTON(gpio_num, ev_code, act_low, descr, wake) \ @@ -171,6 +180,8 @@ static struct imxi2c_platform_data mx53_ard_i2c3_data = { static void __init mx53_ard_io_init(void) { + int ret; + mxc_iomux_v3_setup_multiple_pads(mx53_ard_pads, ARRAY_SIZE(mx53_ard_pads)); @@ -179,6 +190,14 @@ static void __init mx53_ard_io_init(void) gpio_request(ARD_I2CPORTEXP_B, "i2cptexp-rst"); gpio_direction_output(ARD_I2CPORTEXP_B, 1); + + ret = gpio_request_one(ARD_CAN_EN, GPIOF_OUT_INIT_HIGH, "can-en"); + if (ret) + pr_err("Cannot request ARD_CAN_EN pin: %d\n", ret); + + ret = gpio_request_one(ARD_CAN_STBY, GPIOF_OUT_INIT_HIGH, "can-stby"); + if (ret) + pr_err("Cannot request ARD_CAN_STBY pin: %d\n", ret); } /* Config CS1 settings for ethernet controller */ @@ -234,6 +253,8 @@ static void __init mx53_ard_board_init(void) imx53_add_imx_i2c(1, &mx53_ard_i2c2_data); imx53_add_imx_i2c(2, &mx53_ard_i2c3_data); imx_add_gpio_keys(&ard_button_data); + imx53_add_flexcan0(NULL); + imx53_add_flexcan1(NULL); } static void __init mx53_ard_timer_init(void)
Adding flexcan support on i.MX53 ARD Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com> --- arch/arm/mach-mx5/Kconfig | 1 + arch/arm/mach-mx5/board-mx53_ard.c | 21 +++++++++++++++++++++ 2 files changed, 22 insertions(+), 0 deletions(-)