| Message ID | 1313138752-24006-4-git-send-email-holt@sgi.com |
|---|---|
| State | Superseded, archived |
| Delegated to: | David Miller |
| Headers | show |
Grant, Earlier, you had asked for a more specific name for the compatible property of the Freescale flexcan device. I still have not gotten a more specific answer. Hopefully Marc can give you more details about the flexcan implementations. Other than an agreement on the compatible property, I believe we have agreement on all the other code changes in these patches. Is this change acceptable as is and if we get a better resolution on the fsl,flexcan name later, we can update the documentation and driver then? Thanks, Robin On Fri, Aug 12, 2011 at 03:45:49AM -0500, Robin Holt wrote: > This patch cleans up the documentation of the device-tree binding for > the Flexcan devices on Freescale's PowerPC and ARM cores. Extra > properties are not used by the driver so we are removing them. > > Signed-off-by: Robin Holt <holt@sgi.com> > Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>, > To: Wolfgang Grandegger <wg@grandegger.com>, > To: U Bhaskar-B22300 <B22300@freescale.com> > To: Scott Wood <scottwood@freescale.com> > To: Grant Likely <grant.likely@secretlab.ca> > To: Kumar Gala <galak@kernel.crashing.org> > Cc: socketcan-core@lists.berlios.de, > Cc: netdev@vger.kernel.org, > Cc: PPC list <linuxppc-dev@lists.ozlabs.org> > Cc: devicetree-discuss@lists.ozlabs.org > --- > .../devicetree/bindings/net/can/fsl-flexcan.txt | 61 ++++---------------- > arch/powerpc/boot/dts/p1010rdb.dts | 10 +--- > arch/powerpc/boot/dts/p1010si.dtsi | 10 +-- > 3 files changed, 17 insertions(+), 64 deletions(-) > > diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt > index 1a729f0..80a78a9 100644 > --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt > +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt > @@ -1,61 +1,22 @@ > -CAN Device Tree Bindings > ------------------------- > -2011 Freescale Semiconductor, Inc. > +Flexcan CAN contoller on Freescale's ARM and PowerPC system-on-a-chip (SOC). > > -fsl,flexcan-v1.0 nodes > ------------------------ > -In addition to the required compatible-, reg- and interrupt-properties, you can > -also specify which clock source shall be used for the controller. > +Required properties: > > -CPI Clock- Can Protocol Interface Clock > - This CLK_SRC bit of CTRL(control register) selects the clock source to > - the CAN Protocol Interface(CPI) to be either the peripheral clock > - (driven by the PLL) or the crystal oscillator clock. The selected clock > - is the one fed to the prescaler to generate the Serial Clock (Sclock). > - The PRESDIV field of CTRL(control register) controls a prescaler that > - generates the Serial Clock (Sclock), whose period defines the > - time quantum used to compose the CAN waveform. > +- compatible : Should be "fsl,<processor>-flexcan" and "fsl,flexcan" > > -Can Engine Clock Source > - There are two sources for CAN clock > - - Platform Clock It represents the bus clock > - - Oscillator Clock > + An implementation should also claim any of the following compatibles > + that it is fully backwards compatible with: > > - Peripheral Clock (PLL) > - -------------- > - | > - --------- ------------- > - | |CPI Clock | Prescaler | Sclock > - | |---------------->| (1.. 256) |------------> > - --------- ------------- > - | | > - -------------- ---------------------CLK_SRC > - Oscillator Clock > + - fsl,p1010-flexcan > > -- fsl,flexcan-clock-source : CAN Engine Clock Source.This property selects > - the peripheral clock. PLL clock is fed to the > - prescaler to generate the Serial Clock (Sclock). > - Valid values are "oscillator" and "platform" > - "oscillator": CAN engine clock source is oscillator clock. > - "platform" The CAN engine clock source is the bus clock > - (platform clock). > +- reg : Offset and length of the register set for this device > +- interrupts : Interrupt tuple for this device > > -- fsl,flexcan-clock-divider : for the reference and system clock, an additional > - clock divider can be specified. > -- clock-frequency: frequency required to calculate the bitrate for FlexCAN. > +Example: > > -Note: > - - v1.0 of flexcan-v1.0 represent the IP block version for P1010 SOC. > - - P1010 does not have oscillator as the Clock Source.So the default > - Clock Source is platform clock. > -Examples: > - > - can0@1c000 { > - compatible = "fsl,flexcan-v1.0"; > + can@1c000 { > + compatible = "fsl,p1010-flexcan", "fsl,flexcan"; > reg = <0x1c000 0x1000>; > interrupts = <48 0x2>; > interrupt-parent = <&mpic>; > - fsl,flexcan-clock-source = "platform"; > - fsl,flexcan-clock-divider = <2>; > - clock-frequency = <fixed by u-boot>; > }; > diff --git a/arch/powerpc/boot/dts/p1010rdb.dts b/arch/powerpc/boot/dts/p1010rdb.dts > index 6b33b73..d6c669c 100644 > --- a/arch/powerpc/boot/dts/p1010rdb.dts > +++ b/arch/powerpc/boot/dts/p1010rdb.dts > @@ -23,6 +23,8 @@ > ethernet2 = &enet2; > pci0 = &pci0; > pci1 = &pci1; > + can0 = &can0; > + can1 = &can1; > }; > > memory { > @@ -169,14 +171,6 @@ > }; > }; > > - can0@1c000 { > - fsl,flexcan-clock-source = "platform"; > - }; > - > - can1@1d000 { > - fsl,flexcan-clock-source = "platform"; > - }; > - > usb@22000 { > phy_type = "utmi"; > }; > diff --git a/arch/powerpc/boot/dts/p1010si.dtsi b/arch/powerpc/boot/dts/p1010si.dtsi > index 7f51104..f00076b 100644 > --- a/arch/powerpc/boot/dts/p1010si.dtsi > +++ b/arch/powerpc/boot/dts/p1010si.dtsi > @@ -140,20 +140,18 @@ > interrupt-parent = <&mpic>; > }; > > - can0@1c000 { > - compatible = "fsl,flexcan-v1.0"; > + can0: can@1c000 { > + compatible = "fsl,p1010-flexcan", "fsl,flexcan"; > reg = <0x1c000 0x1000>; > interrupts = <48 0x2>; > interrupt-parent = <&mpic>; > - fsl,flexcan-clock-divider = <2>; > }; > > - can1@1d000 { > - compatible = "fsl,flexcan-v1.0"; > + can1: can@1d000 { > + compatible = "fsl,p1010-flexcan", "fsl,flexcan"; > reg = <0x1d000 0x1000>; > interrupts = <61 0x2>; > interrupt-parent = <&mpic>; > - fsl,flexcan-clock-divider = <2>; > }; > > L2: l2-cache-controller@20000 { > -- > 1.7.2.1 -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Mon, Aug 15, 2011 at 9:03 AM, Robin Holt <holt@sgi.com> wrote: > Grant, > > Earlier, you had asked for a more specific name for the compatible > property of the Freescale flexcan device. I still have not gotten a > more specific answer. Hopefully Marc can give you more details about > the flexcan implementations. If there is no ip core version, then just stick with the fsl,<soc>-flexcan name and drop "fsl,flexcan". Marketing may say flexcan is flexcan, but hardware engineers like to change things. Trying to be too generic in compatible values will just lead to problems in the future. g. -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Mon, Aug 15, 2011 at 09:13:50AM -0600, Grant Likely wrote: > On Mon, Aug 15, 2011 at 9:03 AM, Robin Holt <holt@sgi.com> wrote: > > Grant, > > > > Earlier, you had asked for a more specific name for the compatible > > property of the Freescale flexcan device. I still have not gotten a > > more specific answer. Hopefully Marc can give you more details about > > the flexcan implementations. > > If there is no ip core version, then just stick with the > fsl,<soc>-flexcan name and drop "fsl,flexcan". Marketing may say > flexcan is flexcan, but hardware engineers like to change things. > Trying to be too generic in compatible values will just lead to > problems in the future. Thanks, Robin -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 08/15/2011 05:03 PM, Robin Holt wrote: > Earlier, you had asked for a more specific name for the compatible > property of the Freescale flexcan device. I still have not gotten a > more specific answer. Hopefully Marc can give you more details about > the flexcan implementations. There are at least 2 versions of the flexcan ip core in the wild. Due to lack of version numbers or other names I call them old and new here :). The newer one supports rx fifo mode, whereas the older one doesn't. The mainline flexcan driver just supports the new core [1]. The older core is found on coldfire processors. I don't know if there are coldfire cpus with the new flexcan core, too. The driver can be adopted to the old core if needed. The first cpus with the new core I got in touch with was the mx35 (arm11) and mx25 (arm9) both at the same time. Ask fsl which one was released first. After this there was mx28 (arm9) and there should be an mx53 (coretexa8) with flexcan too. > Other than an agreement on the compatible property, I believe we have > agreement on all the other code changes in these patches. Is this change > acceptable as is and if we get a better resolution on the fsl,flexcan > name later, we can update the documentation and driver then? cheers, Marc [1] http://lxr.linux.no/linux+v3.0.1/drivers/net/can/flexcan.c#L871
diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt index 1a729f0..80a78a9 100644 --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -1,61 +1,22 @@ -CAN Device Tree Bindings ------------------------- -2011 Freescale Semiconductor, Inc. +Flexcan CAN contoller on Freescale's ARM and PowerPC system-on-a-chip (SOC). -fsl,flexcan-v1.0 nodes ------------------------ -In addition to the required compatible-, reg- and interrupt-properties, you can -also specify which clock source shall be used for the controller. +Required properties: -CPI Clock- Can Protocol Interface Clock - This CLK_SRC bit of CTRL(control register) selects the clock source to - the CAN Protocol Interface(CPI) to be either the peripheral clock - (driven by the PLL) or the crystal oscillator clock. The selected clock - is the one fed to the prescaler to generate the Serial Clock (Sclock). - The PRESDIV field of CTRL(control register) controls a prescaler that - generates the Serial Clock (Sclock), whose period defines the - time quantum used to compose the CAN waveform. +- compatible : Should be "fsl,<processor>-flexcan" and "fsl,flexcan" -Can Engine Clock Source - There are two sources for CAN clock - - Platform Clock It represents the bus clock - - Oscillator Clock + An implementation should also claim any of the following compatibles + that it is fully backwards compatible with: - Peripheral Clock (PLL) - -------------- - | - --------- ------------- - | |CPI Clock | Prescaler | Sclock - | |---------------->| (1.. 256) |------------> - --------- ------------- - | | - -------------- ---------------------CLK_SRC - Oscillator Clock + - fsl,p1010-flexcan -- fsl,flexcan-clock-source : CAN Engine Clock Source.This property selects - the peripheral clock. PLL clock is fed to the - prescaler to generate the Serial Clock (Sclock). - Valid values are "oscillator" and "platform" - "oscillator": CAN engine clock source is oscillator clock. - "platform" The CAN engine clock source is the bus clock - (platform clock). +- reg : Offset and length of the register set for this device +- interrupts : Interrupt tuple for this device -- fsl,flexcan-clock-divider : for the reference and system clock, an additional - clock divider can be specified. -- clock-frequency: frequency required to calculate the bitrate for FlexCAN. +Example: -Note: - - v1.0 of flexcan-v1.0 represent the IP block version for P1010 SOC. - - P1010 does not have oscillator as the Clock Source.So the default - Clock Source is platform clock. -Examples: - - can0@1c000 { - compatible = "fsl,flexcan-v1.0"; + can@1c000 { + compatible = "fsl,p1010-flexcan", "fsl,flexcan"; reg = <0x1c000 0x1000>; interrupts = <48 0x2>; interrupt-parent = <&mpic>; - fsl,flexcan-clock-source = "platform"; - fsl,flexcan-clock-divider = <2>; - clock-frequency = <fixed by u-boot>; }; diff --git a/arch/powerpc/boot/dts/p1010rdb.dts b/arch/powerpc/boot/dts/p1010rdb.dts index 6b33b73..d6c669c 100644 --- a/arch/powerpc/boot/dts/p1010rdb.dts +++ b/arch/powerpc/boot/dts/p1010rdb.dts @@ -23,6 +23,8 @@ ethernet2 = &enet2; pci0 = &pci0; pci1 = &pci1; + can0 = &can0; + can1 = &can1; }; memory { @@ -169,14 +171,6 @@ }; }; - can0@1c000 { - fsl,flexcan-clock-source = "platform"; - }; - - can1@1d000 { - fsl,flexcan-clock-source = "platform"; - }; - usb@22000 { phy_type = "utmi"; }; diff --git a/arch/powerpc/boot/dts/p1010si.dtsi b/arch/powerpc/boot/dts/p1010si.dtsi index 7f51104..f00076b 100644 --- a/arch/powerpc/boot/dts/p1010si.dtsi +++ b/arch/powerpc/boot/dts/p1010si.dtsi @@ -140,20 +140,18 @@ interrupt-parent = <&mpic>; }; - can0@1c000 { - compatible = "fsl,flexcan-v1.0"; + can0: can@1c000 { + compatible = "fsl,p1010-flexcan", "fsl,flexcan"; reg = <0x1c000 0x1000>; interrupts = <48 0x2>; interrupt-parent = <&mpic>; - fsl,flexcan-clock-divider = <2>; }; - can1@1d000 { - compatible = "fsl,flexcan-v1.0"; + can1: can@1d000 { + compatible = "fsl,p1010-flexcan", "fsl,flexcan"; reg = <0x1d000 0x1000>; interrupts = <61 0x2>; interrupt-parent = <&mpic>; - fsl,flexcan-clock-divider = <2>; }; L2: l2-cache-controller@20000 {