| Message ID | 20201016093138.28871-3-vadivel.muruganx.ramuthevar@linux.intel.com |
|---|---|
| State | Changes Requested, archived |
| Headers | show |
| Series | spi: cadence-quadspi: Add QSPI controller support for Intel LGM SoC | expand |
| Context | Check | Description |
|---|---|---|
| robh/checkpatch | warning | total: 0 errors, 3 warnings, 148 lines checked |
On Fri, Oct 16, 2020 at 05:31:34PM +0800, Ramuthevar,Vadivel MuruganX wrote: > From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> > > Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml > remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/ Please make YAML conversions the last thing in any patch series - there's sometimes a backlog on reviews as the DT maintainers are very busy so this means that delays with them don't hold the rest of the series up.
Hi Mark, On 17/10/2020 12:18 am, Mark Brown wrote: > On Fri, Oct 16, 2020 at 05:31:34PM +0800, Ramuthevar,Vadivel MuruganX wrote: >> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> >> >> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml >> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/ > > Please make YAML conversions the last thing in any patch series - > there's sometimes a backlog on reviews as the DT maintainers are very > busy so this means that delays with them don't hold the rest of the > series up. Thank you for the comment and suggestions... Sure, will do that accordingly. Regards Vadivel >
On Fri, Oct 16, 2020 at 05:31:34PM +0800, Ramuthevar,Vadivel MuruganX wrote: > From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> > > Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml > remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/ > > Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> > --- > .../devicetree/bindings/spi/cadence-quadspi.txt | 67 ---------- > .../devicetree/bindings/spi/cadence-quadspi.yaml | 148 +++++++++++++++++++++ > 2 files changed, 148 insertions(+), 67 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt > create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml > > diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt > deleted file mode 100644 > index 945be7d5b236..000000000000 > --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt > +++ /dev/null > @@ -1,67 +0,0 @@ > -* Cadence Quad SPI controller > - > -Required properties: > -- compatible : should be one of the following: > - Generic default - "cdns,qspi-nor". > - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor". > - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor". > -- reg : Contains two entries, each of which is a tuple consisting of a > - physical address and length. The first entry is the address and > - length of the controller register set. The second entry is the > - address and length of the QSPI Controller data area. > -- interrupts : Unit interrupt specifier for the controller interrupt. > -- clocks : phandle to the Quad SPI clock. > -- cdns,fifo-depth : Size of the data FIFO in words. > -- cdns,fifo-width : Bus width of the data FIFO in bytes. > -- cdns,trigger-address : 32-bit indirect AHB trigger address. > - > -Optional properties: > -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not. > -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch > - the read data rather than the QSPI clock. Make sure that QSPI return > - clock is populated on the board before using this property. > - > -Optional subnodes: > -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional > -custom properties: > -- cdns,read-delay : Delay for read capture logic, in clock cycles > -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master > - mode chip select outputs are de-asserted between > - transactions. > -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being > - de-activated and the activation of another. > -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current > - transaction and deasserting the device chip select > - (qspi_n_ss_out). > -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low > - and first bit transfer. > -- resets : Must contain an entry for each entry in reset-names. > - See ../reset/reset.txt for details. > -- reset-names : Must include either "qspi" and/or "qspi-ocp". > - > -Example: > - > - qspi: spi@ff705000 { > - compatible = "cdns,qspi-nor"; > - #address-cells = <1>; > - #size-cells = <0>; > - reg = <0xff705000 0x1000>, > - <0xffa00000 0x1000>; > - interrupts = <0 151 4>; > - clocks = <&qspi_clk>; > - cdns,is-decoded-cs; > - cdns,fifo-depth = <128>; > - cdns,fifo-width = <4>; > - cdns,trigger-address = <0x00000000>; > - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>; > - reset-names = "qspi", "qspi-ocp"; > - > - flash0: n25q00@0 { > - ... > - cdns,read-delay = <4>; > - cdns,tshsl-ns = <50>; > - cdns,tsd2d-ns = <50>; > - cdns,tchsh-ns = <4>; > - cdns,tslch-ns = <4>; > - }; > - }; > diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml > new file mode 100644 > index 000000000000..6ed8122a1326 > --- /dev/null > +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml > @@ -0,0 +1,148 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Cadence Quad SPI controller > + > +maintainers: > + - Vadivel Murugan <vadivel.muruganx.ramuthevar@intel.com> > + > +allOf: > + - $ref: "spi-controller.yaml#" > + > +properties: > + compatible: > + items: > + - const: cdns,qspi-nor > + - const: ti,k2g-qspi, cdns,qspi-nor > + - const: ti,am654-ospi, cdns,qspi-nor This says that compatible must be: compatible = "cdns,qspi-nor", "ti,k2g-qspi, cdns,qspi-nor", "ti,am654-ospi, cdns,qspi-nor"; You need 'oneOf' here. > + > + description: > + Should be one of the above supported compatible strings. Drop. > + optional properties > + "cdns,is-decoded-cs" - Flag to indicate whether decoder is used or not. > + "cdns,rclk-en" - Flag to indicate that QSPI return clock is used to latch > + the read data rather than the QSPI clock. Make sure that QSPI return > + clock is populated on the board before using this property. Needs to be actual schema properties. > + > + reg: > + maxItems: 2 > + > + description: > + Contains two entries, each of which is a tuple consisting of a > + physical address and length. The first entry is the address and > + length of the controller register set. The second entry is the > + address and length of the QSPI Controller data area. reg: items: - description: the controller register set - description: the controller data area > + > + interrupts: > + maxItems: 1 > + description: > + Unit interrupt specifier for the controller interrupt. Drop description. > + > + clocks: > + maxItems: 1 > + description: > + phandle to the Quad SPI clock. Drop description. > + > + cdns,fifo-depth: > + description: > + Size of the data FIFO in words. > + allOf: Don't need allOf here now. > + - $ref: "/schemas/types.yaml#/definitions/uint32" > + - enum: [ 128, 256 ] > + - default: 128 > + > + cdns,fifo-width: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Bus width of the data FIFO in bytes. > + multipleOf: 4 minimum/maximum? > + > + cdns,trigger-address: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + 32-bit indirect AHB trigger address. > + > + resets: How many (maxItems)? > + description: > + Must contain an entry for each entry in reset-names. > + See ../reset/reset.txt for details. Drop. > + > + reset-names: > + description: > + Must include either "qspi" and/or "qspi-ocp". Needs to be schema constraints. > + > +# subnode's properties > +patternProperties: > + "@[0-9a-f]+$": > + type: object > + description: > + flash device uses the subnodes below defined properties. > + > + cdns,read-delay: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + Delay for read capture logic, in clock cycles. > + > + cdns,tshsl-ns: > + description: | > + Delay in nanoseconds for the length that the master mode chip select > + outputs are de-asserted between transactions. > + > + cdns,tsd2d-ns: > + description: | > + Delay in nanoseconds between one chip select being de-activated > + and the activation of another. > + > + cdns,tchsh-ns: > + description: | > + Delay in nanoseconds between last bit of current transaction and > + deasserting the device chip select (qspi_n_ss_out). > + > + cdns,tslch-ns: > + description: | > + Delay in nanoseconds between setting qspi_n_ss_out low and > + first bit transfer. > + > +required: > + - compatible > + - reg > + - interrupts > + - clocks > + - cdns,fifo-depth > + - cdns,fifo-width > + - cdns,trigger-address > + - resets > + - reset-names additionalProperties: false > + > +examples: > + - | > + qspi: spi@ff705000 { > + compatible = "cadence,qspi"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0xff705000 0x1000>, > + <0xffa00000 0x1000>; > + interrupts = <0 151 4>; > + clocks = <&qspi_clk>; > + cdns,fifo-depth = <128>; > + cdns,fifo-width = <4>; > + cdns,trigger-address = <0x00000000>; > + resets = <&rst 0x1>, <&rst 0x2>; > + reset-names = "qspi", "qspi-ocp"; > + > + flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0x0>; > + cdns,read-delay = <4>; > + cdns,tshsl-ns = <50>; > + cdns,tsd2d-ns = <50>; > + cdns,tchsh-ns = <4>; > + cdns,tslch-ns = <4>; > + }; > + > + }; > + > +... > -- > 2.11.0 >
Hi Rob, Thank you for review comments... On 20/10/2020 5:35 am, Rob Herring wrote: > On Fri, Oct 16, 2020 at 05:31:34PM +0800, Ramuthevar,Vadivel MuruganX wrote: >> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> >> >> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml >> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/ >> >> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> >> --- >> .../devicetree/bindings/spi/cadence-quadspi.txt | 67 ---------- >> .../devicetree/bindings/spi/cadence-quadspi.yaml | 148 +++++++++++++++++++++ >> 2 files changed, 148 insertions(+), 67 deletions(-) >> delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt >> create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml >> >> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt >> deleted file mode 100644 >> index 945be7d5b236..000000000000 >> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt >> +++ /dev/null >> @@ -1,67 +0,0 @@ >> -* Cadence Quad SPI controller >> - >> -Required properties: >> -- compatible : should be one of the following: >> - Generic default - "cdns,qspi-nor". >> - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor". >> - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor". >> -- reg : Contains two entries, each of which is a tuple consisting of a >> - physical address and length. The first entry is the address and >> - length of the controller register set. The second entry is the >> - address and length of the QSPI Controller data area. >> -- interrupts : Unit interrupt specifier for the controller interrupt. >> -- clocks : phandle to the Quad SPI clock. >> -- cdns,fifo-depth : Size of the data FIFO in words. >> -- cdns,fifo-width : Bus width of the data FIFO in bytes. >> -- cdns,trigger-address : 32-bit indirect AHB trigger address. >> - >> -Optional properties: >> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not. >> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch >> - the read data rather than the QSPI clock. Make sure that QSPI return >> - clock is populated on the board before using this property. >> - >> -Optional subnodes: >> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional >> -custom properties: >> -- cdns,read-delay : Delay for read capture logic, in clock cycles >> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master >> - mode chip select outputs are de-asserted between >> - transactions. >> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being >> - de-activated and the activation of another. >> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current >> - transaction and deasserting the device chip select >> - (qspi_n_ss_out). >> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low >> - and first bit transfer. >> -- resets : Must contain an entry for each entry in reset-names. >> - See ../reset/reset.txt for details. >> -- reset-names : Must include either "qspi" and/or "qspi-ocp". >> - >> -Example: >> - >> - qspi: spi@ff705000 { >> - compatible = "cdns,qspi-nor"; >> - #address-cells = <1>; >> - #size-cells = <0>; >> - reg = <0xff705000 0x1000>, >> - <0xffa00000 0x1000>; >> - interrupts = <0 151 4>; >> - clocks = <&qspi_clk>; >> - cdns,is-decoded-cs; >> - cdns,fifo-depth = <128>; >> - cdns,fifo-width = <4>; >> - cdns,trigger-address = <0x00000000>; >> - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>; >> - reset-names = "qspi", "qspi-ocp"; >> - >> - flash0: n25q00@0 { >> - ... >> - cdns,read-delay = <4>; >> - cdns,tshsl-ns = <50>; >> - cdns,tsd2d-ns = <50>; >> - cdns,tchsh-ns = <4>; >> - cdns,tslch-ns = <4>; >> - }; >> - }; >> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml >> new file mode 100644 >> index 000000000000..6ed8122a1326 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml >> @@ -0,0 +1,148 @@ >> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Cadence Quad SPI controller >> + >> +maintainers: >> + - Vadivel Murugan <vadivel.muruganx.ramuthevar@intel.com> >> + >> +allOf: >> + - $ref: "spi-controller.yaml#" >> + >> +properties: >> + compatible: >> + items: >> + - const: cdns,qspi-nor >> + - const: ti,k2g-qspi, cdns,qspi-nor >> + - const: ti,am654-ospi, cdns,qspi-nor > > This says that compatible must be: > > compatible = "cdns,qspi-nor", "ti,k2g-qspi, cdns,qspi-nor", "ti,am654-ospi, cdns,qspi-nor"; > > You need 'oneOf' here. Noted, will update. > >> + >> + description: >> + Should be one of the above supported compatible strings. > > Drop. okay > >> + optional properties >> + "cdns,is-decoded-cs" - Flag to indicate whether decoder is used or not. >> + "cdns,rclk-en" - Flag to indicate that QSPI return clock is used to latch >> + the read data rather than the QSPI clock. Make sure that QSPI return >> + clock is populated on the board before using this property. > > Needs to be actual schema properties. Noted. > >> + >> + reg: >> + maxItems: 2 >> + >> + description: >> + Contains two entries, each of which is a tuple consisting of a >> + physical address and length. The first entry is the address and >> + length of the controller register set. The second entry is the >> + address and length of the QSPI Controller data area. > > reg: > items: > - description: the controller register set > - description: the controller data area Noted, Thank you for the pointer. > >> + >> + interrupts: >> + maxItems: 1 >> + description: >> + Unit interrupt specifier for the controller interrupt. > > Drop description. will drop. > >> + >> + clocks: >> + maxItems: 1 >> + description: >> + phandle to the Quad SPI clock. > > Drop description. will drop. > >> + >> + cdns,fifo-depth: >> + description: >> + Size of the data FIFO in words. >> + allOf: > > Don't need allOf here now. will remove , noted > >> + - $ref: "/schemas/types.yaml#/definitions/uint32" >> + - enum: [ 128, 256 ] >> + - default: 128 >> + >> + cdns,fifo-width: >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + description: >> + Bus width of the data FIFO in bytes. >> + multipleOf: 4 > > minimum/maximum? it's fixed width, so will add default instead of minimum/maximum. > >> + >> + cdns,trigger-address: >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + description: >> + 32-bit indirect AHB trigger address. >> + >> + resets: > > How many (maxItems)? maxItems : 2 > >> + description: >> + Must contain an entry for each entry in reset-names. >> + See ../reset/reset.txt for details. > > Drop. Noted, will drop. > >> + >> + reset-names: >> + description: >> + Must include either "qspi" and/or "qspi-ocp". > > Needs to be schema constraints. Okay, noted. > >> + >> +# subnode's properties >> +patternProperties: >> + "@[0-9a-f]+$": >> + type: object >> + description: >> + flash device uses the subnodes below defined properties. >> + >> + cdns,read-delay: >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + description: >> + Delay for read capture logic, in clock cycles. >> + >> + cdns,tshsl-ns: >> + description: | >> + Delay in nanoseconds for the length that the master mode chip select >> + outputs are de-asserted between transactions. >> + >> + cdns,tsd2d-ns: >> + description: | >> + Delay in nanoseconds between one chip select being de-activated >> + and the activation of another. >> + >> + cdns,tchsh-ns: >> + description: | >> + Delay in nanoseconds between last bit of current transaction and >> + deasserting the device chip select (qspi_n_ss_out). >> + >> + cdns,tslch-ns: >> + description: | >> + Delay in nanoseconds between setting qspi_n_ss_out low and >> + first bit transfer. >> + >> +required: >> + - compatible >> + - reg >> + - interrupts >> + - clocks >> + - cdns,fifo-depth >> + - cdns,fifo-width >> + - cdns,trigger-address >> + - resets >> + - reset-names > > additionalProperties: false Noted, thanks! Regards Vadivel > >> + >> +examples: >> + - | >> + qspi: spi@ff705000 { >> + compatible = "cadence,qspi"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + reg = <0xff705000 0x1000>, >> + <0xffa00000 0x1000>; >> + interrupts = <0 151 4>; >> + clocks = <&qspi_clk>; >> + cdns,fifo-depth = <128>; >> + cdns,fifo-width = <4>; >> + cdns,trigger-address = <0x00000000>; >> + resets = <&rst 0x1>, <&rst 0x2>; >> + reset-names = "qspi", "qspi-ocp"; >> + >> + flash@0 { >> + compatible = "jedec,spi-nor"; >> + reg = <0x0>; >> + cdns,read-delay = <4>; >> + cdns,tshsl-ns = <50>; >> + cdns,tsd2d-ns = <50>; >> + cdns,tchsh-ns = <4>; >> + cdns,tslch-ns = <4>; >> + }; >> + >> + }; >> + >> +... >> -- >> 2.11.0 >>
diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt deleted file mode 100644 index 945be7d5b236..000000000000 --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt +++ /dev/null @@ -1,67 +0,0 @@ -* Cadence Quad SPI controller - -Required properties: -- compatible : should be one of the following: - Generic default - "cdns,qspi-nor". - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor". - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor". -- reg : Contains two entries, each of which is a tuple consisting of a - physical address and length. The first entry is the address and - length of the controller register set. The second entry is the - address and length of the QSPI Controller data area. -- interrupts : Unit interrupt specifier for the controller interrupt. -- clocks : phandle to the Quad SPI clock. -- cdns,fifo-depth : Size of the data FIFO in words. -- cdns,fifo-width : Bus width of the data FIFO in bytes. -- cdns,trigger-address : 32-bit indirect AHB trigger address. - -Optional properties: -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not. -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch - the read data rather than the QSPI clock. Make sure that QSPI return - clock is populated on the board before using this property. - -Optional subnodes: -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional -custom properties: -- cdns,read-delay : Delay for read capture logic, in clock cycles -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master - mode chip select outputs are de-asserted between - transactions. -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being - de-activated and the activation of another. -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current - transaction and deasserting the device chip select - (qspi_n_ss_out). -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low - and first bit transfer. -- resets : Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names : Must include either "qspi" and/or "qspi-ocp". - -Example: - - qspi: spi@ff705000 { - compatible = "cdns,qspi-nor"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0xff705000 0x1000>, - <0xffa00000 0x1000>; - interrupts = <0 151 4>; - clocks = <&qspi_clk>; - cdns,is-decoded-cs; - cdns,fifo-depth = <128>; - cdns,fifo-width = <4>; - cdns,trigger-address = <0x00000000>; - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>; - reset-names = "qspi", "qspi-ocp"; - - flash0: n25q00@0 { - ... - cdns,read-delay = <4>; - cdns,tshsl-ns = <50>; - cdns,tsd2d-ns = <50>; - cdns,tchsh-ns = <4>; - cdns,tslch-ns = <4>; - }; - }; diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml new file mode 100644 index 000000000000..6ed8122a1326 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml @@ -0,0 +1,148 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence Quad SPI controller + +maintainers: + - Vadivel Murugan <vadivel.muruganx.ramuthevar@intel.com> + +allOf: + - $ref: "spi-controller.yaml#" + +properties: + compatible: + items: + - const: cdns,qspi-nor + - const: ti,k2g-qspi, cdns,qspi-nor + - const: ti,am654-ospi, cdns,qspi-nor + + description: + Should be one of the above supported compatible strings. + optional properties + "cdns,is-decoded-cs" - Flag to indicate whether decoder is used or not. + "cdns,rclk-en" - Flag to indicate that QSPI return clock is used to latch + the read data rather than the QSPI clock. Make sure that QSPI return + clock is populated on the board before using this property. + + reg: + maxItems: 2 + + description: + Contains two entries, each of which is a tuple consisting of a + physical address and length. The first entry is the address and + length of the controller register set. The second entry is the + address and length of the QSPI Controller data area. + + interrupts: + maxItems: 1 + description: + Unit interrupt specifier for the controller interrupt. + + clocks: + maxItems: 1 + description: + phandle to the Quad SPI clock. + + cdns,fifo-depth: + description: + Size of the data FIFO in words. + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 128, 256 ] + - default: 128 + + cdns,fifo-width: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Bus width of the data FIFO in bytes. + multipleOf: 4 + + cdns,trigger-address: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + 32-bit indirect AHB trigger address. + + resets: + description: + Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + + reset-names: + description: + Must include either "qspi" and/or "qspi-ocp". + +# subnode's properties +patternProperties: + "@[0-9a-f]+$": + type: object + description: + flash device uses the subnodes below defined properties. + + cdns,read-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Delay for read capture logic, in clock cycles. + + cdns,tshsl-ns: + description: | + Delay in nanoseconds for the length that the master mode chip select + outputs are de-asserted between transactions. + + cdns,tsd2d-ns: + description: | + Delay in nanoseconds between one chip select being de-activated + and the activation of another. + + cdns,tchsh-ns: + description: | + Delay in nanoseconds between last bit of current transaction and + deasserting the device chip select (qspi_n_ss_out). + + cdns,tslch-ns: + description: | + Delay in nanoseconds between setting qspi_n_ss_out low and + first bit transfer. + +required: + - compatible + - reg + - interrupts + - clocks + - cdns,fifo-depth + - cdns,fifo-width + - cdns,trigger-address + - resets + - reset-names + +examples: + - | + qspi: spi@ff705000 { + compatible = "cadence,qspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xff705000 0x1000>, + <0xffa00000 0x1000>; + interrupts = <0 151 4>; + clocks = <&qspi_clk>; + cdns,fifo-depth = <128>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x00000000>; + resets = <&rst 0x1>, <&rst 0x2>; + reset-names = "qspi", "qspi-ocp"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0x0>; + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + }; + + }; + +...