[v2] pinctrl: nsp: Set irq handler based on trig type

Rather than always using handle_simple_irq() as the gpio_irq_chip
handler, set a more appropriate handler based on the IRQ trigger type
requested. This is important for level triggered interrupts which need
to be masked during handling. Also, fix the interrupt acknowledge so
that it clears only one interrupt instead of all interrupts which are
currently active. Finally there is no need to clear the interrupt during
the interrupt handler, since the edge-triggered handler will do that for
us.

Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
---
Changes in v2:
- Don't perform unnecessary acks.

 drivers/pinctrl/bcm/pinctrl-nsp-gpio.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

Hi Mark,

On 7/2/2020 6:18 PM, Mark Tomlinson wrote:
> Rather than always using handle_simple_irq() as the gpio_irq_chip
> handler, set a more appropriate handler based on the IRQ trigger type
> requested. This is important for level triggered interrupts which need
> to be masked during handling. Also, fix the interrupt acknowledge so
> that it clears only one interrupt instead of all interrupts which are
> currently active. Finally there is no need to clear the interrupt during
> the interrupt handler, since the edge-triggered handler will do that for
> us.
> 
> Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
> ---
> Changes in v2:
> - Don't perform unnecessary acks.
> 
>  drivers/pinctrl/bcm/pinctrl-nsp-gpio.c | 18 +++++++++---------
>  1 file changed, 9 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/pinctrl/bcm/pinctrl-nsp-gpio.c b/drivers/pinctrl/bcm/pinctrl-nsp-gpio.c
> index bed0124388c0..a00a42a61a90 100644
> --- a/drivers/pinctrl/bcm/pinctrl-nsp-gpio.c
> +++ b/drivers/pinctrl/bcm/pinctrl-nsp-gpio.c
> @@ -154,15 +154,9 @@ static irqreturn_t nsp_gpio_irq_handler(int irq, void *data)
>  		level &= readl(chip->base + NSP_GPIO_INT_MASK);
>  		int_bits = level | event;
>  
> -		for_each_set_bit(bit, &int_bits, gc->ngpio) {
> -			/*
> -			 * Clear the interrupt before invoking the
> -			 * handler, so we do not leave any window
> -			 */
> -			writel(BIT(bit), chip->base + NSP_GPIO_EVENT);
> +		for_each_set_bit(bit, &int_bits, gc->ngpio)
>  			generic_handle_irq(
>  				irq_linear_revmap(gc->irq.domain, bit));
> -		}
>  	}
>  
>  	return  int_bits ? IRQ_HANDLED : IRQ_NONE;
> @@ -178,7 +172,7 @@ static void nsp_gpio_irq_ack(struct irq_data *d)
>  
>  	trigger_type = irq_get_trigger_type(d->irq);
>  	if (trigger_type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
> -		nsp_set_bit(chip, REG, NSP_GPIO_EVENT, gpio, val);
> +		writel(val, chip->base + NSP_GPIO_EVENT);
>  }
>  
>  /*
> @@ -262,6 +256,12 @@ static int nsp_gpio_irq_set_type(struct irq_data *d, unsigned int type)
>  
>  	nsp_set_bit(chip, REG, NSP_GPIO_EVENT_INT_POLARITY, gpio, falling);
>  	nsp_set_bit(chip, REG, NSP_GPIO_INT_POLARITY, gpio, level_low);
> +
> +	if (type & IRQ_TYPE_EDGE_BOTH)
> +		irq_set_handler_locked(d, handle_edge_irq);
> +	else
> +		irq_set_handler_locked(d, handle_level_irq);
> +
>  	raw_spin_unlock_irqrestore(&chip->lock, flags);
>  
>  	dev_dbg(chip->dev, "gpio:%u level_low:%s falling:%s\n", gpio,
> @@ -691,7 +691,7 @@ static int nsp_gpio_probe(struct platform_device *pdev)
>  		girq->num_parents = 0;
>  		girq->parents = NULL;
>  		girq->default_type = IRQ_TYPE_NONE;
> -		girq->handler = handle_simple_irq;
> +		girq->handler = handle_bad_irq;
>  	}
>  
>  	ret = devm_gpiochip_add_data(dev, gc, chip);
> 

This change looks good to me. Thanks!

Reviewed-by: Ray Jui <ray.jui@broadcom.com>

On Fri, Jul 3, 2020 at 3:18 AM Mark Tomlinson
<mark.tomlinson@alliedtelesis.co.nz> wrote:

> Rather than always using handle_simple_irq() as the gpio_irq_chip
> handler, set a more appropriate handler based on the IRQ trigger type
> requested. This is important for level triggered interrupts which need
> to be masked during handling. Also, fix the interrupt acknowledge so
> that it clears only one interrupt instead of all interrupts which are
> currently active. Finally there is no need to clear the interrupt during
> the interrupt handler, since the edge-triggered handler will do that for
> us.
>
> Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
> ---
> Changes in v2:
> - Don't perform unnecessary acks.

Patch applied.

Yours,
Linus Walleij