| Message ID | 20200620224222.1312520-1-j.neuschaefer@gmx.net |
|---|---|
| State | RFC, archived |
| Headers | show |
| Series | Netronix embedded controller driver for Kobo and Tolino ebook readers | expand |
| Context | Check | Description |
|---|---|---|
| robh/checkpatch | success | |
| robh/dt-meta-schema | success |
On Sun, Jun 21, 2020 at 12:42:13AM +0200, Jonathan Neuschäfer wrote:
> Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
Oops, it seems the mail thread got split here when I resent patches 2-10
after an error. Oh well.
On 21/06/2020 00:42:19+0200, Jonathan Neuschäfer wrote: > With this driver, mainline Linux can keep its time and date in sync with > the vendor kernel. > > Advanced functionality like alarm and automatic power-on is not yet > supported. > Please report the results of rtctest (from the kernel tree) and rtc-range (https://git.kernel.org/pub/scm/linux/kernel/git/abelloni/rtc-tools.git/tree/rtc-range.c) > Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> > --- > drivers/rtc/Kconfig | 4 ++ > drivers/rtc/Makefile | 1 + > drivers/rtc/rtc-ntxec.c | 115 ++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 120 insertions(+) > create mode 100644 drivers/rtc/rtc-ntxec.c > > diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig > index b54d87d45c89b..2310d08933f9c 100644 > --- a/drivers/rtc/Kconfig > +++ b/drivers/rtc/Kconfig > @@ -1300,6 +1300,10 @@ config RTC_DRV_CROS_EC > This driver can also be built as a module. If so, the module > will be called rtc-cros-ec. > > +config RTC_DRV_NTXEC > + tristate "Netronix embedded controller RTC driver" > + depends on MFD_NTXEC > + This should get an help section. > comment "on-CPU RTC drivers" > > config RTC_DRV_ASM9260 > diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile > index 0721752c6ed4c..8653d04aefa99 100644 > --- a/drivers/rtc/Makefile > +++ b/drivers/rtc/Makefile > @@ -111,6 +111,7 @@ obj-$(CONFIG_RTC_DRV_MT7622) += rtc-mt7622.o > obj-$(CONFIG_RTC_DRV_MV) += rtc-mv.o > obj-$(CONFIG_RTC_DRV_MXC) += rtc-mxc.o > obj-$(CONFIG_RTC_DRV_MXC_V2) += rtc-mxc_v2.o > +obj-$(CONFIG_RTC_DRV_NTXEC) += rtc-ntxec.o > obj-$(CONFIG_RTC_DRV_OMAP) += rtc-omap.o > obj-$(CONFIG_RTC_DRV_OPAL) += rtc-opal.o > obj-$(CONFIG_RTC_DRV_PALMAS) += rtc-palmas.o > diff --git a/drivers/rtc/rtc-ntxec.c b/drivers/rtc/rtc-ntxec.c > new file mode 100644 > index 0000000000000..44d5a5eedb597 > --- /dev/null > +++ b/drivers/rtc/rtc-ntxec.c > @@ -0,0 +1,115 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +// Copyright 2020 Jonathan Neuschäfer > + > +#include <linux/rtc.h> > +#include <linux/mfd/ntxec.h> > +#include <linux/platform_device.h> > +#include <linux/types.h> > +#include <linux/module.h> > +#include <linux/of_device.h> Please sort the includes. > + > +struct ntxec_rtc { > + struct device *dev; > + struct ntxec *ec; > +}; > + > +#define NTXEC_WRITE_YEAR 0x10 > +#define NTXEC_WRITE_MONTH 0x11 > +#define NTXEC_WRITE_DAY 0x12 > +#define NTXEC_WRITE_HOUR 0x13 > +#define NTXEC_WRITE_MINUTE 0x14 > +#define NTXEC_WRITE_SECOND 0x15 > + > +#define NTXEC_READ_YM 0x20 > +#define NTXEC_READ_DH 0x21 > +#define NTXEC_READ_MS 0x22 > + > + > +static int ntxec_read_time(struct device *dev, struct rtc_time *tm) > +{ > + struct ntxec_rtc *rtc = dev_get_drvdata(dev); > + int res; > + > + res = ntxec_read16(rtc->ec, NTXEC_READ_YM); > + if (res < 0) > + return res; > + > + tm->tm_year = (res >> 8) + 100; > + tm->tm_mon = (res & 0xff) - 1; > + > + res = ntxec_read16(rtc->ec, NTXEC_READ_DH); > + if (res < 0) > + return res; > + > + tm->tm_mday = res >> 8; > + tm->tm_hour = res & 0xff; > + > + res = ntxec_read16(rtc->ec, NTXEC_READ_MS); > + if (res < 0) > + return res; > + > + tm->tm_min = res >> 8; > + tm->tm_sec = res & 0xff; > + > + return 0; > +} > + > +static int ntxec_set_time(struct device *dev, struct rtc_time *tm) > +{ > + struct ntxec_rtc *rtc = dev_get_drvdata(dev); > + int res = 0; > + > + res |= ntxec_write8(rtc->ec, NTXEC_WRITE_YEAR, tm->tm_year - 100); > + res |= ntxec_write8(rtc->ec, NTXEC_WRITE_MONTH, tm->tm_mon + 1); > + res |= ntxec_write8(rtc->ec, NTXEC_WRITE_DAY, tm->tm_mday); > + res |= ntxec_write8(rtc->ec, NTXEC_WRITE_HOUR, tm->tm_hour); > + res |= ntxec_write8(rtc->ec, NTXEC_WRITE_MINUTE, tm->tm_min); > + res |= ntxec_write8(rtc->ec, NTXEC_WRITE_SECOND, tm->tm_sec); > + > + return (res < 0)? -EIO : 0; > +} > + > +static const struct rtc_class_ops ntxec_rtc_ops = { > + .read_time = ntxec_read_time, > + .set_time = ntxec_set_time, > +}; > + > +static int ntxec_rtc_probe(struct platform_device *pdev) > +{ > + struct rtc_device *rtcdev; > + struct ntxec_rtc *rtc; > + > + rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL); > + if (!rtc) > + return -ENOMEM; > + > + rtc->dev = &pdev->dev; > + rtc->ec = dev_get_drvdata(pdev->dev.parent); > + platform_set_drvdata(pdev, rtc); > + > + rtcdev = devm_rtc_device_register(&pdev->dev, "ntxec-rtc", > + &ntxec_rtc_ops, THIS_MODULE); Please use devm_rtc_allocate_device and rtc_register_device. Also, set the supported range (->range_min and ->range_max).
Hello, On Sun, Jun 21, 2020 at 12:42:17AM +0200, Jonathan Neuschäfer wrote: > The Netronix EC provides a PWM output, which is used for the backlight s/,// > on ebook readers. This patches adds a driver for the PWM output. on *some* ebook readers > +#define NTXEC_UNK_A 0xa1 > +#define NTXEC_UNK_B 0xa2 > +#define NTXEC_ENABLE 0xa3 > +#define NTXEC_PERIOD_LOW 0xa4 > +#define NTXEC_PERIOD_HIGH 0xa5 > +#define NTXEC_DUTY_LOW 0xa6 > +#define NTXEC_DUTY_HIGH 0xa7 > + > +/* > + * The time base used in the EC is 8MHz, or 125ns. Period and duty cycle are > + * measured in this unit. > + */ > +static int ntxec_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm_dev, > + int duty_ns, int period_ns) > +{ > + struct ntxec_pwm *pwm = pwmchip_to_pwm(chip); > + uint64_t duty = duty_ns; > + uint64_t period = period_ns; As you cannot use values bigger than 8191999 anyhow, I wonder why you use a 64 bit type here. > + int res = 0; > + > + do_div(period, 125); Please use a define instead of plain 125. > + if (period > 0xffff) { > + dev_warn(pwm->dev, > + "Period is not representable in 16 bits: %llu\n", period); > + return -ERANGE; > + } > + > + do_div(duty, 125); > + if (duty > 0xffff) { > + dev_warn(pwm->dev, "Duty cycle is not representable in 16 bits: %llu\n", > + duty); > + return -ERANGE; > + } This check isn't necessary as the pwm core ensures that duty <= period. > + res |= ntxec_write8(pwm->ec, NTXEC_PERIOD_HIGH, period >> 8); > + res |= ntxec_write8(pwm->ec, NTXEC_PERIOD_LOW, period); > + res |= ntxec_write8(pwm->ec, NTXEC_DUTY_HIGH, duty >> 8); > + res |= ntxec_write8(pwm->ec, NTXEC_DUTY_LOW, duty); Does this complete the currently running period? Can it happen that a new period starts between the first and the last write and so a mixed period can be seen at the output? > + > + return (res < 0) ? -EIO : 0; > +} > + > +static int ntxec_pwm_enable(struct pwm_chip *chip, > + struct pwm_device *pwm_dev) > +{ > + struct ntxec_pwm *pwm = pwmchip_to_pwm(chip); > + > + return ntxec_write8(pwm->ec, NTXEC_ENABLE, 1); > +} > + > +static void ntxec_pwm_disable(struct pwm_chip *chip, > + struct pwm_device *pwm_dev) > +{ > + struct ntxec_pwm *pwm = pwmchip_to_pwm(chip); > + > + ntxec_write8(pwm->ec, NTXEC_ENABLE, 0); > +} > + > +static struct pwm_ops ntxec_pwm_ops = { > + .config = ntxec_pwm_config, > + .enable = ntxec_pwm_enable, > + .disable = ntxec_pwm_disable, > + .owner = THIS_MODULE, Please don't align the =, just a single space before them is fine. More important: Please implement .apply() (and .get_state()) instead of the old API. Also please enable PWM_DEBUG which might save us a review iteration. > +}; > + > +static int ntxec_pwm_probe(struct platform_device *pdev) > +{ > + struct ntxec *ec = dev_get_drvdata(pdev->dev.parent); > + struct ntxec_pwm *pwm; > + struct pwm_chip *chip; > + int res; > + > + pwm = devm_kzalloc(&pdev->dev, sizeof(*pwm), GFP_KERNEL); > + if (!pwm) > + return -ENOMEM; > + > + pwm->ec = ec; > + pwm->dev = &pdev->dev; > + > + chip = &pwm->chip; > + chip->dev = &pdev->dev; > + chip->ops = &ntxec_pwm_ops; > + chip->base = -1; > + chip->npwm = 1; > + > + res = pwmchip_add(chip); > + if (res < 0) > + return res; > + > + platform_set_drvdata(pdev, pwm); > + > + res |= ntxec_write8(pwm->ec, NTXEC_ENABLE, 0); > + res |= ntxec_write8(pwm->ec, NTXEC_UNK_A, 0xff); > + res |= ntxec_write8(pwm->ec, NTXEC_UNK_B, 0xff); > + > + return (res < 0) ? -EIO : 0; This is broken for several reasons: - You're not supposed to modify the output in .probe - if ntxec_write8 results in an error you keep the pwm registered. - From the moment on pwmchip_add returns the callbacks can be called. The calls to ntxec_write8 probably interfere here. Best regards Uwe
On Sun, 21 Jun 2020, Jonathan Neuschäfer wrote: Description of the device here please. > Third-party hardware documentation is available at '\n' > https://github.com/neuschaefer/linux/wiki/Netronix-MSP430-embedded-controller Indent this with a couple of spaces. > The EC supports interrupts, but the driver doesn't make use of them so > far. > > Known problems: > - The reboot handler is installed in such a way that it directly calls > into the i2c subsystem to send the reboot command to the EC. This > means that the reboot handler may sleep, which is not allowed. > > Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> > --- > drivers/mfd/Kconfig | 7 ++ > drivers/mfd/Makefile | 1 + > drivers/mfd/ntxec.c | 188 ++++++++++++++++++++++++++++++++++++++ > include/linux/mfd/ntxec.h | 30 ++++++ > 4 files changed, 226 insertions(+) > create mode 100644 drivers/mfd/ntxec.c > create mode 100644 include/linux/mfd/ntxec.h > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig > index a37d7d1713820..78410b928648e 100644 > --- a/drivers/mfd/Kconfig > +++ b/drivers/mfd/Kconfig > @@ -978,6 +978,13 @@ config MFD_VIPERBOARD > You need to select the mfd cell drivers separately. > The drivers do not support all features the board exposes. > > +config MFD_NTXEC > + bool "Netronix Embedded Controller" > + depends on I2C && OF > + help > + Say yes here if you want to support the embedded controller of > + certain e-book readers designed by the ODM Netronix. s/of certain/found in certain/. > config MFD_RETU > tristate "Nokia Retu and Tahvo multi-function device" > select MFD_CORE > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile > index 9367a92f795a6..19d9391ed6f32 100644 > --- a/drivers/mfd/Makefile > +++ b/drivers/mfd/Makefile > @@ -218,6 +218,7 @@ obj-$(CONFIG_MFD_INTEL_MSIC) += intel_msic.o > obj-$(CONFIG_MFD_INTEL_PMC_BXT) += intel_pmc_bxt.o > obj-$(CONFIG_MFD_PALMAS) += palmas.o > obj-$(CONFIG_MFD_VIPERBOARD) += viperboard.o > +obj-$(CONFIG_MFD_NTXEC) += ntxec.o > obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o > obj-$(CONFIG_MFD_RK808) += rk808.o > obj-$(CONFIG_MFD_RN5T618) += rn5t618.o > diff --git a/drivers/mfd/ntxec.c b/drivers/mfd/ntxec.c > new file mode 100644 > index 0000000000000..82adea34ea746 > --- /dev/null > +++ b/drivers/mfd/ntxec.c > @@ -0,0 +1,188 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +// Copyright 2020 Jonathan Neuschäfer > +// > +// MFD driver for the usually MSP430-based embedded controller used in certain > +// Netronix ebook reader board designs Only the SPDX line should contain C++ style comments. Description at the top, copyright after. An "MFD driver" isn't really a thing. Please describe the device. > +#include <asm/unaligned.h> > +#include <linux/delay.h> > +#include <linux/errno.h> > +#include <linux/i2c.h> > +#include <linux/mfd/ntxec.h> > +#include <linux/of_platform.h> > +#include <linux/pm.h> > +#include <linux/reboot.h> > +#include <linux/types.h> > + > + No need for double line spacing. > +#define NTXEC_VERSION 0x00 > +#define NTXEC_POWEROFF 0x50 > +#define NTXEC_POWERKEEP 0x70 > +#define NTXEC_RESET 0x90 Are these registers? Might be worth pre/post-fixing with _REG. > +/* Register access */ > + > +int ntxec_read16(struct ntxec *ec, u8 addr) > +{ > + u8 request[1] = { addr }; > + u8 response[2]; > + int res; > + > + struct i2c_msg msgs[] = { > + { > + .addr = ec->client->addr, > + .flags = ec->client->flags, > + .len = sizeof(request), > + .buf = request > + }, { > + .addr = ec->client->addr, > + .flags = ec->client->flags | I2C_M_RD, > + .len = sizeof(response), > + .buf = response > + } > + }; > + > + res = i2c_transfer(ec->client->adapter, msgs, ARRAY_SIZE(msgs)); > + if (res < 0) > + return res; > + if (res != ARRAY_SIZE(msgs)) > + return -EIO; > + > + return get_unaligned_be16(response); > +} > +EXPORT_SYMBOL(ntxec_read16); > + > +int ntxec_write16(struct ntxec *ec, u8 addr, u16 value) > +{ > + u8 request[3] = { addr, }; > + int res; > + > + put_unaligned_be16(value, request + 1); > + > + res = i2c_transfer_buffer_flags(ec->client, request, sizeof(request), > + ec->client->flags); > + if (res < 0) > + return res; > + > + return 0; > +} > +EXPORT_SYMBOL(ntxec_write16); > + > +int ntxec_read8(struct ntxec *ec, u8 addr) > +{ > + int res = ntxec_read16(ec, addr); > + > + if (res < 0) > + return res; > + > + return (res >> 8) & 0xff; > +} > +EXPORT_SYMBOL(ntxec_read8); > + > +int ntxec_write8(struct ntxec *ec, u8 addr, u8 value) > +{ > + return ntxec_write16(ec, addr, value << 8); > +} > +EXPORT_SYMBOL(ntxec_write8); Why are you hand-rolling your own accessors? > + > + > +/* Reboot/poweroff handling */ These comments seem to be stating the obvious. Please remove them. > +static struct ntxec *poweroff_restart_instance; > + > +static void ntxec_poweroff(void) > +{ > + ntxec_write8(poweroff_restart_instance, NTXEC_POWEROFF, 0x01); All magic numbers should be defined? > + msleep(5000); Why 5000? > +} > + > +static int ntxec_restart(struct notifier_block *nb, > + unsigned long action, void *data) > +{ > + /* FIXME: The I2C driver sleeps, but restart handlers may not sleep */ Then this is not allowed. You need to fix this *before* submitting upstream. > + ntxec_write8(poweroff_restart_instance, NTXEC_RESET, 0xff); > + /* TODO: delay? */ TODO *before* submitting upstream. This is not a development branch. > + return NOTIFY_DONE; > +} > + > +static struct notifier_block ntxec_restart_handler = { > + .notifier_call = ntxec_restart, > + .priority = 128 > +}; > + > + > +/* Driver setup */ > + > +static int ntxec_probe(struct i2c_client *client, > + const struct i2c_device_id *ids) > +{ > + struct ntxec *ec; > + int res; What does 'res' mean? > + ec = devm_kmalloc(&client->dev, sizeof(*ec), GFP_KERNEL); > + if (!ec) > + return -ENOMEM; > + > + ec->dev = &client->dev; > + ec->client = client; You don't need both (if any). > + /* Determine the firmware version */ > + res = ntxec_read16(ec, NTXEC_VERSION); > + if (res < 0) { > + dev_dbg(ec->dev, "Failed to read firmware version number\n"); Why dbg? > + return res; > + } > + ec->version = res; > + > + dev_info(ec->dev, > + "Netronix embedded controller version %04x detected.\n", > + ec->version); > + > + /* For now, we don't support the new register layout. */ > + if (ntxec_has_new_layout(ec)) > + return -EOPNOTSUPP; What is the new layout? Why don't you support it? > + if (of_device_is_system_power_controller(ec->dev->of_node)) { > + /* > + * Set the 'powerkeep' bit. This is necessary on some boards > + * in order to keep the system running. > + */ > + res = ntxec_write8(ec, NTXEC_POWERKEEP, 0x08); > + if (res < 0) > + return res; > + > + /* Install poweroff handler */ > + WARN_ON(poweroff_restart_instance); Why WARN? > + poweroff_restart_instance = ec; > + if (pm_power_off != NULL) if (pm_power_off) > + /* TODO: Refactor among all poweroff drivers */ Nope. > + dev_err(ec->dev, "pm_power_off already assigned\n"); Error, but execution carries on anyway? > + else > + pm_power_off = ntxec_poweroff; > + > + /* Install board reset handler */ > + res = register_restart_handler(&ntxec_restart_handler); > + if (res < 0) Is >0 valid? > + dev_err(ec->dev, > + "Failed to register restart handler: %d\n", res); > + } > + > + i2c_set_clientdata(client, ec); Where do you use this? > + return devm_of_platform_populate(ec->dev); > +} > + > +static const struct of_device_id of_ntxec_match_table[] = { > + { .compatible = "netronix,ntxec", }, > + {} > +}; Use .probe_new() and drop this. > +static struct i2c_driver ntxec_driver = { > + .driver = { > + .name = "ntxec", > + .of_match_table = of_ntxec_match_table, > + }, > + .probe = ntxec_probe, Nothing to .remove()? > +}; > +builtin_i2c_driver(ntxec_driver); Only built-in? > diff --git a/include/linux/mfd/ntxec.h b/include/linux/mfd/ntxec.h > new file mode 100644 > index 0000000000000..9f9d6f2141751 > --- /dev/null > +++ b/include/linux/mfd/ntxec.h > @@ -0,0 +1,30 @@ > +/* SPDX-License-Identifier: GPL-2.0-only */ > +/* > + * Copyright 2020 Jonathan Neuschäfer > + * > + * MFD access functions for the Netronix embedded controller. No such thing as an MFD. "Embedded Controller" > + */ > + > +#ifndef NTXEC_H > +#define NTXEC_H > + > +#include <linux/types.h> > + > +struct ntxec { > + struct device *dev; > + struct i2c_client *client; > + u16 version; > + /* TODO: Add a mutex to protect actions consisting of multiple accesses? */ No TODOs. Please fix before upstreaming. > +}; > + > +static inline bool ntxec_has_new_layout(struct ntxec *ec) > +{ > + return ec->version == 0xe916; Why don't you just check for the devices you *do* support? > +} > + > +int ntxec_read16(struct ntxec *ec, u8 addr); > +int ntxec_write16(struct ntxec *ec, u8 addr, u16 value); > +int ntxec_read8(struct ntxec *ec, u8 addr); > +int ntxec_write8(struct ntxec *ec, u8 addr, u8 value); > + > +#endif #endif /* NTXEC_H */
On Sun, 21 Jun 2020 00:42:15 +0200 Jonathan Neuschäfer <j.neuschaefer@gmx.net> wrote: > Third-party hardware documentation is available at > https://github.com/neuschaefer/linux/wiki/Netronix-MSP430-embedded-controller > > The EC supports interrupts, but the driver doesn't make use of them so > far. > > Known problems: > - The reboot handler is installed in such a way that it directly calls > into the i2c subsystem to send the reboot command to the EC. This > means that the reboot handler may sleep, which is not allowed. > see https://patchwork.ozlabs.org/project/linux-i2c/patch/20190415213432.8972-3-contact@stefanchrist.eu/ for a fix of such problems. > Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> > --- > drivers/mfd/Kconfig | 7 ++ > drivers/mfd/Makefile | 1 + > drivers/mfd/ntxec.c | 188 ++++++++++++++++++++++++++++++++++++++ > include/linux/mfd/ntxec.h | 30 ++++++ > 4 files changed, 226 insertions(+) > create mode 100644 drivers/mfd/ntxec.c > create mode 100644 include/linux/mfd/ntxec.h > > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig > index a37d7d1713820..78410b928648e 100644 > --- a/drivers/mfd/Kconfig > +++ b/drivers/mfd/Kconfig > @@ -978,6 +978,13 @@ config MFD_VIPERBOARD > You need to select the mfd cell drivers separately. > The drivers do not support all features the board exposes. > > +config MFD_NTXEC > + bool "Netronix Embedded Controller" > + depends on I2C && OF > + help > + Say yes here if you want to support the embedded controller of > + certain e-book readers designed by the ODM Netronix. > + > config MFD_RETU > tristate "Nokia Retu and Tahvo multi-function device" > select MFD_CORE > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile > index 9367a92f795a6..19d9391ed6f32 100644 > --- a/drivers/mfd/Makefile > +++ b/drivers/mfd/Makefile > @@ -218,6 +218,7 @@ obj-$(CONFIG_MFD_INTEL_MSIC) += intel_msic.o > obj-$(CONFIG_MFD_INTEL_PMC_BXT) += intel_pmc_bxt.o > obj-$(CONFIG_MFD_PALMAS) += palmas.o > obj-$(CONFIG_MFD_VIPERBOARD) += viperboard.o > +obj-$(CONFIG_MFD_NTXEC) += ntxec.o > obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o > obj-$(CONFIG_MFD_RK808) += rk808.o > obj-$(CONFIG_MFD_RN5T618) += rn5t618.o > diff --git a/drivers/mfd/ntxec.c b/drivers/mfd/ntxec.c > new file mode 100644 > index 0000000000000..82adea34ea746 > --- /dev/null > +++ b/drivers/mfd/ntxec.c > @@ -0,0 +1,188 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +// Copyright 2020 Jonathan Neuschäfer > +// > +// MFD driver for the usually MSP430-based embedded controller used in certain > +// Netronix ebook reader board designs > + > +#include <asm/unaligned.h> > +#include <linux/delay.h> > +#include <linux/errno.h> > +#include <linux/i2c.h> > +#include <linux/mfd/ntxec.h> > +#include <linux/of_platform.h> > +#include <linux/pm.h> > +#include <linux/reboot.h> > +#include <linux/types.h> > + > + > +#define NTXEC_VERSION 0x00 > +#define NTXEC_POWEROFF 0x50 > +#define NTXEC_POWERKEEP 0x70 > +#define NTXEC_RESET 0x90 > + > + > +/* Register access */ > + > +int ntxec_read16(struct ntxec *ec, u8 addr) > +{ > + u8 request[1] = { addr }; > + u8 response[2]; > + int res; > + > + struct i2c_msg msgs[] = { > + { > + .addr = ec->client->addr, > + .flags = ec->client->flags, > + .len = sizeof(request), > + .buf = request > + }, { > + .addr = ec->client->addr, > + .flags = ec->client->flags | I2C_M_RD, > + .len = sizeof(response), > + .buf = response > + } > + }; > + > + res = i2c_transfer(ec->client->adapter, msgs, ARRAY_SIZE(msgs)); > + if (res < 0) > + return res; > + if (res != ARRAY_SIZE(msgs)) > + return -EIO; > + > + return get_unaligned_be16(response); > +} > +EXPORT_SYMBOL(ntxec_read16); > + > +int ntxec_write16(struct ntxec *ec, u8 addr, u16 value) > +{ > + u8 request[3] = { addr, }; > + int res; > + > + put_unaligned_be16(value, request + 1); > + > + res = i2c_transfer_buffer_flags(ec->client, request, sizeof(request), > + ec->client->flags); > + if (res < 0) > + return res; > + > + return 0; > +} > +EXPORT_SYMBOL(ntxec_write16); > + > +int ntxec_read8(struct ntxec *ec, u8 addr) > +{ > + int res = ntxec_read16(ec, addr); > + > + if (res < 0) > + return res; > + > + return (res >> 8) & 0xff; > +} > +EXPORT_SYMBOL(ntxec_read8); > + > +int ntxec_write8(struct ntxec *ec, u8 addr, u8 value) > +{ > + return ntxec_write16(ec, addr, value << 8); > +} > +EXPORT_SYMBOL(ntxec_write8); > + do we really need both 16bit and 8bit accessors? If not, then simply use regmap_i2c_init and set val_bits accordingly. Maybe just doing the << 8 in the constants? > + > +/* Reboot/poweroff handling */ > + > +static struct ntxec *poweroff_restart_instance; > + > +static void ntxec_poweroff(void) > +{ > + ntxec_write8(poweroff_restart_instance, NTXEC_POWEROFF, 0x01); > + msleep(5000); > +} > + > +static int ntxec_restart(struct notifier_block *nb, > + unsigned long action, void *data) > +{ > + /* FIXME: The I2C driver sleeps, but restart handlers may not sleep */ > + ntxec_write8(poweroff_restart_instance, NTXEC_RESET, 0xff); > + /* TODO: delay? */ > + return NOTIFY_DONE; > +} > + > +static struct notifier_block ntxec_restart_handler = { > + .notifier_call = ntxec_restart, > + .priority = 128 > +}; > + > + > +/* Driver setup */ > + > +static int ntxec_probe(struct i2c_client *client, > + const struct i2c_device_id *ids) > +{ > + struct ntxec *ec; > + int res; > + > + ec = devm_kmalloc(&client->dev, sizeof(*ec), GFP_KERNEL); > + if (!ec) > + return -ENOMEM; > + > + ec->dev = &client->dev; > + ec->client = client; > + > + /* Determine the firmware version */ > + res = ntxec_read16(ec, NTXEC_VERSION); > + if (res < 0) { > + dev_dbg(ec->dev, "Failed to read firmware version number\n"); > + return res; > + } > + ec->version = res; > + > + dev_info(ec->dev, > + "Netronix embedded controller version %04x detected.\n", > + ec->version); > + > + /* For now, we don't support the new register layout. */ > + if (ntxec_has_new_layout(ec)) > + return -EOPNOTSUPP; > + > + if (of_device_is_system_power_controller(ec->dev->of_node)) { > + /* > + * Set the 'powerkeep' bit. This is necessary on some boards > + * in order to keep the system running. > + */ > + res = ntxec_write8(ec, NTXEC_POWERKEEP, 0x08); > + if (res < 0) > + return res; > + > + /* Install poweroff handler */ > + WARN_ON(poweroff_restart_instance); > + poweroff_restart_instance = ec; > + if (pm_power_off != NULL) > + /* TODO: Refactor among all poweroff drivers */ > + dev_err(ec->dev, "pm_power_off already assigned\n"); > + else > + pm_power_off = ntxec_poweroff; > + common pattern, across drivers, so I think doing something else would be a separate cleanup issue. Regards, Andreas
On Mon, Jun 22, 2020 at 11:55:44AM +0100, Lee Jones wrote: > On Sun, 21 Jun 2020, Jonathan Neuschäfer wrote: > > Description of the device here please. > > > Third-party hardware documentation is available at > > '\n' > > > https://github.com/neuschaefer/linux/wiki/Netronix-MSP430-embedded-controller > > Indent this with a couple of spaces. > [...] > > + help > > + Say yes here if you want to support the embedded controller of > > + certain e-book readers designed by the ODM Netronix. > > s/of certain/found in certain/. [...] > > +++ b/drivers/mfd/ntxec.c > > @@ -0,0 +1,188 @@ > > +// SPDX-License-Identifier: GPL-2.0-only > > +// Copyright 2020 Jonathan Neuschäfer > > +// > > +// MFD driver for the usually MSP430-based embedded controller used in certain > > +// Netronix ebook reader board designs > > Only the SPDX line should contain C++ style comments. > > Description at the top, copyright after. > > An "MFD driver" isn't really a thing. Please describe the device. [...] > > +#include <linux/types.h> > > + > > + > > No need for double line spacing. Alright, I'll fix these. > > +#define NTXEC_VERSION 0x00 > > +#define NTXEC_POWEROFF 0x50 > > +#define NTXEC_POWERKEEP 0x70 > > +#define NTXEC_RESET 0x90 > > Are these registers? Might be worth pre/post-fixing with _REG. Yes, good idea. > > > +/* Register access */ > > + > > +int ntxec_read16(struct ntxec *ec, u8 addr) > > +{ > > + u8 request[1] = { addr }; > > + u8 response[2]; > > + int res; > > + > > + struct i2c_msg msgs[] = { > > + { > > + .addr = ec->client->addr, > > + .flags = ec->client->flags, > > + .len = sizeof(request), > > + .buf = request > > + }, { > > + .addr = ec->client->addr, > > + .flags = ec->client->flags | I2C_M_RD, > > + .len = sizeof(response), > > + .buf = response > > + } > > + }; > > + > > + res = i2c_transfer(ec->client->adapter, msgs, ARRAY_SIZE(msgs)); > > + if (res < 0) > > + return res; > > + if (res != ARRAY_SIZE(msgs)) > > + return -EIO; > > + > > + return get_unaligned_be16(response); > > +} > > +EXPORT_SYMBOL(ntxec_read16); > > + > > +int ntxec_write16(struct ntxec *ec, u8 addr, u16 value) > > +{ > > + u8 request[3] = { addr, }; > > + int res; > > + > > + put_unaligned_be16(value, request + 1); > > + > > + res = i2c_transfer_buffer_flags(ec->client, request, sizeof(request), > > + ec->client->flags); > > + if (res < 0) > > + return res; > > + > > + return 0; > > +} > > +EXPORT_SYMBOL(ntxec_write16); > > + > > +int ntxec_read8(struct ntxec *ec, u8 addr) > > +{ > > + int res = ntxec_read16(ec, addr); > > + > > + if (res < 0) > > + return res; > > + > > + return (res >> 8) & 0xff; > > +} > > +EXPORT_SYMBOL(ntxec_read8); > > + > > +int ntxec_write8(struct ntxec *ec, u8 addr, u8 value) > > +{ > > + return ntxec_write16(ec, addr, value << 8); > > +} > > +EXPORT_SYMBOL(ntxec_write8); > > Why are you hand-rolling your own accessors? There are registers which only require one byte of data and others which require two. This didn't quite seem to fit into the regmap API. It is possible to always use 16-bit accessors directly but that would push shifts into call sites that only use 8 bits. (If the 16 bits are interpreted as big endian) I'm not sure what's ideal here. > > +/* Reboot/poweroff handling */ > > These comments seem to be stating the obvious. > > Please remove them. Ok. > > + ntxec_write8(poweroff_restart_instance, NTXEC_POWEROFF, 0x01); > > All magic numbers should be defined? Alright, I'll move them to the register definitions. > > + msleep(5000); > > Why 5000? The idea was to avoid returning from the poweroff handler by allowing enough time until the power is actually off. However: - I just tested it and the board I have turns off about 80ms after the I2C command. - I'm not sure if returning from the poweroff handler is actually bad. It does seem to be wrong, because I get a lockdep report when I remove the msleep and the kernel reaches do_exit in the reboot syscall handler: Requesting system poweroff [ 14.465312] cfg80211: failed to load regulatory.db [ 14.471171] imx-sdma 63fb0000.sdma: external firmware not found, using ROM firmware [ 14.541097] reboot: Power down [ 14.547296] [ 14.548840] ==================================== [ 14.553477] WARNING: init/156 still has locks held! [ 14.558521] 5.8.0-rc1-00011-g65740c2d29bee-dirty #329 Not tainted [ 14.564647] ------------------------------------ [ 14.569399] 1 lock held by init/156: [ 14.573004] #0: c17278a8 (system_transition_mutex){+.+.}-{3:3}, at: __do_sys_reboot+0x13c/0x1fc [ 14.581978] [ 14.581978] stack backtrace: [ 14.586378] CPU: 0 PID: 156 Comm: init Not tainted 5.8.0-rc1-00011-g65740c2d29bee-dirty #329 [ 14.594834] Hardware name: Freescale i.MX50 (Device Tree Support) [ 14.600979] [<c01121c8>] (unwind_backtrace) from [<c010cf3c>] (show_stack+0x10/0x14) [ 14.608763] [<c010cf3c>] (show_stack) from [<c05e54ec>] (dump_stack+0xe4/0x118) [ 14.616115] [<c05e54ec>] (dump_stack) from [<c0130d54>] (do_exit+0x6ec/0xc04) [ 14.623291] [<c0130d54>] (do_exit) from [<c01582f0>] (__do_sys_reboot+0x148/0x1fc) [ 14.630892] [<c01582f0>] (__do_sys_reboot) from [<c0100080>] (ret_fast_syscall+0x0/0x28) [ 14.639000] Exception stack(0xc8c6dfa8 to 0xc8c6dff0) [ 14.644071] dfa0: 00000000 00000000 fee1dead 28121969 4321fedc 00000000 [ 14.652266] dfc0: 00000000 00000000 00000001 00000058 00000001 00000000 00000000 00000000 [ 14.660458] dfe0: 000a2290 bef21db4 0006db1f b6f02a0c I'll adjust the number a bit and add a comment to explain the msleep call. > > +static int ntxec_restart(struct notifier_block *nb, > > + unsigned long action, void *data) > > +{ > > + /* FIXME: The I2C driver sleeps, but restart handlers may not sleep */ > > Then this is not allowed. > > You need to fix this *before* submitting upstream. > > > + ntxec_write8(poweroff_restart_instance, NTXEC_RESET, 0xff); > > + /* TODO: delay? */ > > TODO *before* submitting upstream. This is not a development branch. Sorry. I'll research how other drivers deal with the issue of sleeping I/O in the reset path. > > +/* Driver setup */ > > + > > +static int ntxec_probe(struct i2c_client *client, > > + const struct i2c_device_id *ids) > > +{ > > + struct ntxec *ec; > > + int res; > > What does 'res' mean? Result > > + ec = devm_kmalloc(&client->dev, sizeof(*ec), GFP_KERNEL); > > + if (!ec) > > + return -ENOMEM; > > + > > + ec->dev = &client->dev; > > + ec->client = client; > > You don't need both (if any). Ok, I'll drop ec->client. > > > + /* Determine the firmware version */ > > + res = ntxec_read16(ec, NTXEC_VERSION); > > + if (res < 0) { > > + dev_dbg(ec->dev, "Failed to read firmware version number\n"); > > Why dbg? I'm not sure anymore, but I agree that it seems more significant than debug level. > > + /* For now, we don't support the new register layout. */ > > + if (ntxec_has_new_layout(ec)) > > + return -EOPNOTSUPP; > > What is the new layout? It's a significantly different command set, see 'if (NEWMSP) ...' in: https://github.com/neuschaefer/linux/blob/vendor/kobo-aura/drivers/mxc/pmic/core/pmic_core_i2c.c > Why don't you support it? I don't have any hardware that uses it. The downstream driver supports both layouts so I wanted to ensure that this driver doesn't use the wrong one. > > + if (of_device_is_system_power_controller(ec->dev->of_node)) { > > + /* > > + * Set the 'powerkeep' bit. This is necessary on some boards > > + * in order to keep the system running. > > + */ > > + res = ntxec_write8(ec, NTXEC_POWERKEEP, 0x08); > > + if (res < 0) > > + return res; > > + > > + /* Install poweroff handler */ > > + WARN_ON(poweroff_restart_instance); > > Why WARN? Two instances of this driver where both try to be the poweroff/restart instance seemed like a situation that is always unintended and a bug in the devicetree (or somewhere else). > > > + poweroff_restart_instance = ec; > > + if (pm_power_off != NULL) > > if (pm_power_off) Ok > > > + /* TODO: Refactor among all poweroff drivers */ > > Nope. Alright. > > > + dev_err(ec->dev, "pm_power_off already assigned\n"); > > Error, but execution carries on anyway? Hmm, I guess if the poweroff handler can't be installed there also isn't much point in installing a restart handler... > > + /* Install board reset handler */ > > + res = register_restart_handler(&ntxec_restart_handler); > > + if (res < 0) > > Is >0 valid? "Currently always returns zero" However, other callers tend to do "if (res)". > > + dev_err(ec->dev, > > + "Failed to register restart handler: %d\n", res); > > + } > > + > > + i2c_set_clientdata(client, ec); > > Where do you use this? The sub-devices drivers (RTC, PWM) call `dev_get_drvdata(pdev->dev.parent)` to get a pointer to the ntxec struct, which is then passed to the register accessors. > > +static const struct of_device_id of_ntxec_match_table[] = { > > + { .compatible = "netronix,ntxec", }, > > + {} > > +}; > > Use .probe_new() and drop this. Ok, I'll switch to .probe_new() Should I really drop the OF match table, though? > > +static struct i2c_driver ntxec_driver = { > > + .driver = { > > + .name = "ntxec", > > + .of_match_table = of_ntxec_match_table, > > + }, > > + .probe = ntxec_probe, > > Nothing to .remove()? Good point, I'll add a remove method. > > +}; > > +builtin_i2c_driver(ntxec_driver); > > Only built-in? Currently, this is consistent with the Kconfig entry, but I'll look into making the driver buildable as a module. > > diff --git a/include/linux/mfd/ntxec.h b/include/linux/mfd/ntxec.h > > new file mode 100644 > > index 0000000000000..9f9d6f2141751 > > --- /dev/null > > +++ b/include/linux/mfd/ntxec.h > > @@ -0,0 +1,30 @@ > > +/* SPDX-License-Identifier: GPL-2.0-only */ > > +/* > > + * Copyright 2020 Jonathan Neuschäfer > > + * > > + * MFD access functions for the Netronix embedded controller. > > No such thing as an MFD. > > "Embedded Controller" Ok, I'll rephrase the comment. > > +struct ntxec { > > + struct device *dev; > > + struct i2c_client *client; > > + u16 version; > > + /* TODO: Add a mutex to protect actions consisting of multiple accesses? */ > > No TODOs. Please fix before upstreaming. Sorry, I'll clean them up. > > +static inline bool ntxec_has_new_layout(struct ntxec *ec) > > +{ > > + return ec->version == 0xe916; > > Why don't you just check for the devices you *do* support? Good point. This would be the most conservative approach. If someone then shows up with a different version, it can be added as tested and known working. Thanks for the review, Jonathan Neuschäfer
On Sat, Jun 27, 2020 at 10:17:38AM +0200, Andreas Kemnade wrote: > On Sun, 21 Jun 2020 00:42:15 +0200 > Jonathan Neuschäfer <j.neuschaefer@gmx.net> wrote: > > > Third-party hardware documentation is available at > > https://github.com/neuschaefer/linux/wiki/Netronix-MSP430-embedded-controller > > > > The EC supports interrupts, but the driver doesn't make use of them so > > far. > > > > Known problems: > > - The reboot handler is installed in such a way that it directly calls > > into the i2c subsystem to send the reboot command to the EC. This > > means that the reboot handler may sleep, which is not allowed. > > > see > https://patchwork.ozlabs.org/project/linux-i2c/patch/20190415213432.8972-3-contact@stefanchrist.eu/ > > for a fix of such problems. So far, regmap isn't involved here, but I'll remember it when I switch to regmap. Between when I first wrote this driver and now, the I2C has added support for transfers in atomic contexts very late in the system's life (exactly what happens when you reset a system via PMIC/EC), so this problem seems to be gone from my driver, for now. (See commit 63b96983a5ddf ("i2c: core: introduce callbacks for atomic transfers")) [...] > > +int ntxec_write8(struct ntxec *ec, u8 addr, u8 value) > > +{ > > + return ntxec_write16(ec, addr, value << 8); > > +} > > +EXPORT_SYMBOL(ntxec_write8); > > + > > do we really need both 16bit and 8bit accessors? No, the hardware/firmware doesn't care. > If not, then simply use regmap_i2c_init and set val_bits accordingly. > Maybe just doing the << 8 in the constants? Thanks, I'll try this approach. The values are not always constants, for example in the PWM driver: res |= ntxec_write8(pwm->ec, NTXEC_PERIOD_HIGH, period >> 8); res |= ntxec_write8(pwm->ec, NTXEC_PERIOD_LOW, period); res |= ntxec_write8(pwm->ec, NTXEC_DUTY_HIGH, duty >> 8); res |= ntxec_write8(pwm->ec, NTXEC_DUTY_LOW, duty); Jonathan
On Mon, Jun 22, 2020 at 10:18:02AM +0200, Uwe Kleine-König wrote: > Hello, > > On Sun, Jun 21, 2020 at 12:42:17AM +0200, Jonathan Neuschäfer wrote: > > The Netronix EC provides a PWM output, which is used for the backlight > > s/,// > > > on ebook readers. This patches adds a driver for the PWM output. > > on *some* ebook readers Ok, I'll fix these. > > > +#define NTXEC_UNK_A 0xa1 > > +#define NTXEC_UNK_B 0xa2 > > +#define NTXEC_ENABLE 0xa3 > > +#define NTXEC_PERIOD_LOW 0xa4 > > +#define NTXEC_PERIOD_HIGH 0xa5 > > +#define NTXEC_DUTY_LOW 0xa6 > > +#define NTXEC_DUTY_HIGH 0xa7 > > + > > +/* > > + * The time base used in the EC is 8MHz, or 125ns. Period and duty cycle are > > + * measured in this unit. > > + */ > > +static int ntxec_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm_dev, > > + int duty_ns, int period_ns) > > +{ > > + struct ntxec_pwm *pwm = pwmchip_to_pwm(chip); > > + uint64_t duty = duty_ns; > > + uint64_t period = period_ns; > > As you cannot use values bigger than 8191999 anyhow, I wonder why you > use a 64 bit type here. No particular reason; I possibly got confused by the division API. I'll use uint32_t instead. > > + int res = 0; > > + > > + do_div(period, 125); > > Please use a define instead of plain 125. Will do. > > + if (period > 0xffff) { > > + dev_warn(pwm->dev, > > + "Period is not representable in 16 bits: %llu\n", period); > > + return -ERANGE; > > + } > > + > > + do_div(duty, 125); > > + if (duty > 0xffff) { > > + dev_warn(pwm->dev, "Duty cycle is not representable in 16 bits: %llu\n", > > + duty); > > + return -ERANGE; > > + } > > This check isn't necessary as the pwm core ensures that duty <= period. Ok, I'll remove it. > > > + res |= ntxec_write8(pwm->ec, NTXEC_PERIOD_HIGH, period >> 8); > > + res |= ntxec_write8(pwm->ec, NTXEC_PERIOD_LOW, period); > > + res |= ntxec_write8(pwm->ec, NTXEC_DUTY_HIGH, duty >> 8); > > + res |= ntxec_write8(pwm->ec, NTXEC_DUTY_LOW, duty); > > Does this complete the currently running period? Can it happen that a > new period starts between the first and the last write and so a mixed > period can be seen at the output? Good question. I haven't measured it, and also don't have the code running on the EC. > > > + > > + return (res < 0) ? -EIO : 0; > > +} > > + > > +static int ntxec_pwm_enable(struct pwm_chip *chip, > > + struct pwm_device *pwm_dev) > > +{ > > + struct ntxec_pwm *pwm = pwmchip_to_pwm(chip); > > + > > + return ntxec_write8(pwm->ec, NTXEC_ENABLE, 1); > > +} > > + > > +static void ntxec_pwm_disable(struct pwm_chip *chip, > > + struct pwm_device *pwm_dev) > > +{ > > + struct ntxec_pwm *pwm = pwmchip_to_pwm(chip); > > + > > + ntxec_write8(pwm->ec, NTXEC_ENABLE, 0); > > +} > > + > > +static struct pwm_ops ntxec_pwm_ops = { > > + .config = ntxec_pwm_config, > > + .enable = ntxec_pwm_enable, > > + .disable = ntxec_pwm_disable, > > + .owner = THIS_MODULE, > > Please don't align the =, just a single space before them is fine. Ok > More important: Please implement .apply() (and .get_state()) instead of > the old API. Also please enable PWM_DEBUG which might save us a review > iteration. Will do! > > > +}; > > + > > +static int ntxec_pwm_probe(struct platform_device *pdev) > > +{ > > + struct ntxec *ec = dev_get_drvdata(pdev->dev.parent); > > + struct ntxec_pwm *pwm; > > + struct pwm_chip *chip; > > + int res; > > + > > + pwm = devm_kzalloc(&pdev->dev, sizeof(*pwm), GFP_KERNEL); > > + if (!pwm) > > + return -ENOMEM; > > + > > + pwm->ec = ec; > > + pwm->dev = &pdev->dev; > > + > > + chip = &pwm->chip; > > + chip->dev = &pdev->dev; > > + chip->ops = &ntxec_pwm_ops; > > + chip->base = -1; > > + chip->npwm = 1; > > + > > + res = pwmchip_add(chip); > > + if (res < 0) > > + return res; > > + > > + platform_set_drvdata(pdev, pwm); > > + > > + res |= ntxec_write8(pwm->ec, NTXEC_ENABLE, 0); > > + res |= ntxec_write8(pwm->ec, NTXEC_UNK_A, 0xff); > > + res |= ntxec_write8(pwm->ec, NTXEC_UNK_B, 0xff); > > + > > + return (res < 0) ? -EIO : 0; > > This is broken for several reasons: > > - You're not supposed to modify the output in .probe > - if ntxec_write8 results in an error you keep the pwm registered. > - From the moment on pwmchip_add returns the callbacks can be called. > The calls to ntxec_write8 probably interfere here. Ok, I'll rework the probe function to avoid these issues. Thanks for the review, Jonathan Neuschäfer
Hi, On Sun, Jun 21, 2020 at 02:11:06AM +0200, Alexandre Belloni wrote: > On 21/06/2020 00:42:19+0200, Jonathan Neuschäfer wrote: > > With this driver, mainline Linux can keep its time and date in sync with > > the vendor kernel. > > > > Advanced functionality like alarm and automatic power-on is not yet > > supported. > > > > Please report the results of rtctest (from the kernel tree) [...] # ./rtctest [==========] Running 7 tests from 2 test cases. [ RUN ] rtc.date_read ../../tools/testing/selftests/rtc/rtctest.c:49:date_read:Current RTC date/time is 11/04/2006 23:11:23. [ OK ] rtc.date_read [ RUN ] rtc.uie_read [ 180.651355] random: crng init done uie_read: Test terminated by timeout [ FAIL ] rtc.uie_read [ RUN ] rtc.uie_select ../../tools/testing/selftests/rtc/rtctest.c:98:uie_select:Expected 0 (0) != rc (0) uie_select: Test terminated by assertion [ FAIL ] rtc.uie_select [ RUN ] rtc.alarm_alm_set ../../tools/testing/selftests/rtc/rtctest.c:129:alarm_alm_set:skip alarms are not supported. [ OK ] rtc.alarm_alm_set [ RUN ] rtc.alarm_wkalm_set ../../tools/testing/selftests/rtc/rtctest.c:185:alarm_wkalm_set:skip alarms are not supported. [ OK ] rtc.alarm_wkalm_set [ RUN ] rtc.alarm_alm_set_minute ../../tools/testing/selftests/rtc/rtctest.c:231:alarm_alm_set_minute:skip alarms are not supported. [ OK ] rtc.alarm_alm_set_minute [ RUN ] rtc.alarm_wkalm_set_minute ../../tools/testing/selftests/rtc/rtctest.c:287:alarm_wkalm_set_minute:skip alarms are not supported. [ OK ] rtc.alarm_wkalm_set_minute [==========] 5 / 7 tests passed. [ FAILED ] > [...] and rtc-range > (https://git.kernel.org/pub/scm/linux/kernel/git/abelloni/rtc-tools.git/tree/rtc-range.c) # ./rtc-range Testing 1970-01-01 00:00:00. KO Read back 2226-01-01 00:01:00. Testing 2000-02-28 23:59:59. KO Read back 2000-02-28 23:28:23. Testing 2020-02-28 23:59:59. KO Read back 2020-02-28 23:28:23. Testing 2038-01-19 03:14:07. KO Read back 2038-01-19 03:19:03. Testing 2069-12-31 23:59:59. KO Read back 2069-12-31 23:31:23. Testing 2079-12-31 23:59:59. KO Read back 2079-12-31 23:31:23. Testing 2099-12-31 23:59:59. KO Read back 2099-12-31 23:31:23. Testing 2255-12-31 23:59:59. KO Read back 2255-12-31 23:31:23. Testing 2100-02-28 23:59:59. KO Read back 2100-02-28 23:28:23. Testing 2106-02-07 06:28:15. KO Read back 2106-02-07 06:07:06. Testing 2262-04-11 23:47:16. KO Read back 2006-04-11 23:11:23. Something is very wrong here. I'll try to fix the failures in rtctest and the problems in rtc-range before version 2 of the patchset. (The 2255 date was my addition, because I suspect this to be the upper limit of the RTC's range.) [...] > > +config RTC_DRV_NTXEC > > + tristate "Netronix embedded controller RTC driver" > > + depends on MFD_NTXEC > > + > > This should get an help section. Ok, I'll add one. [...] > > +#include <linux/rtc.h> > > +#include <linux/mfd/ntxec.h> > > +#include <linux/platform_device.h> > > +#include <linux/types.h> > > +#include <linux/module.h> > > +#include <linux/of_device.h> > > Please sort the includes. Will do. [...] > > + rtcdev = devm_rtc_device_register(&pdev->dev, "ntxec-rtc", > > + &ntxec_rtc_ops, THIS_MODULE); > > Please use devm_rtc_allocate_device and rtc_register_device. Also, set > the supported range (->range_min and ->range_max). Ok, will do. Thanks for the review and the testing tips. Jonathan Neuschäfer
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 9aeab66be85fc..516c6b6668fba 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -704,6 +704,8 @@ patternProperties: description: Broadcom Corporation (formerly NetLogic Microsystems) "^netron-dy,.*": description: Netron DY + "^netronix,.*": + description: Netronix, Inc. "^netxeon,.*": description: Shenzhen Netxeon Technology CO., LTD "^neweast,.*":
Netronix, Inc. (http://www.netronixinc.com/) makes ebook reader board designs, which are for example used in Kobo and Tolino devices. An alternative prefix for Netronix would be "ntx", which is already used in code released by Netronix. It is shorter, but perhaps less clear. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) -- 2.27.0