@@ -60,7 +60,7 @@
serial1 = &uart_A;
};
- linein: audio-codec@0 {
+ linein: audio-codec-0 {
#sound-dai-cells = <0>;
compatible = "everest,es7241";
VDDA-supply = <&vcc_3v3>;
@@ -70,7 +70,7 @@
sound-name-prefix = "Linein";
};
- lineout: audio-codec@1 {
+ lineout: audio-codec-1 {
#sound-dai-cells = <0>;
compatible = "everest,es7154";
VDD-supply = <&vcc_3v3>;
@@ -79,14 +79,14 @@
sound-name-prefix = "Lineout";
};
- spdif_dit: audio-codec@2 {
+ spdif_dit: audio-codec-2 {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
status = "okay";
sound-name-prefix = "DIT";
};
- dmics: audio-codec@3 {
+ dmics: audio-codec-3 {
#sound-dai-cells = <0>;
compatible = "dmic-codec";
num-channels = <7>;
@@ -95,6 +95,13 @@
sound-name-prefix = "MIC";
};
+ spdif_dir: audio-codec-4 {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dir";
+ status = "okay";
+ sound-name-prefix = "DIR";
+ };
+
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
@@ -249,6 +256,9 @@
"TODDR_A IN 2", "TDMIN_C OUT",
"TODDR_B IN 2", "TDMIN_C OUT",
"TODDR_C IN 2", "TDMIN_C OUT",
+ "TODDR_A IN 3", "SPDIFIN Capture",
+ "TODDR_B IN 3", "SPDIFIN Capture",
+ "TODDR_C IN 3", "SPDIFIN Capture",
"TODDR_A IN 4", "PDM Capture",
"TODDR_B IN 4", "PDM Capture",
"TODDR_C IN 4", "PDM Capture",
@@ -272,31 +282,31 @@
<393216000>;
status = "okay";
- dai-link@0 {
+ dai-link-0 {
sound-dai = <&frddr_a>;
};
- dai-link@1 {
+ dai-link-1 {
sound-dai = <&frddr_b>;
};
- dai-link@2 {
+ dai-link-2 {
sound-dai = <&frddr_c>;
};
- dai-link@3 {
+ dai-link-3 {
sound-dai = <&toddr_a>;
};
- dai-link@4 {
+ dai-link-4 {
sound-dai = <&toddr_b>;
};
- dai-link@5 {
+ dai-link-5 {
sound-dai = <&toddr_c>;
};
- dai-link@6 {
+ dai-link-6 {
sound-dai = <&tdmif_c>;
dai-format = "i2s";
dai-tdm-slot-tx-mask-2 = <1 1>;
@@ -317,7 +327,7 @@
};
- dai-link@7 {
+ dai-link-7 {
sound-dai = <&spdifout>;
codec {
@@ -325,7 +335,15 @@
};
};
- dai-link@8 {
+ dai-link-8 {
+ sound-dai = <&spdifin>;
+
+ codec {
+ sound-dai = <&spdif_dir>;
+ };
+ };
+
+ dai-link-9 {
sound-dai = <&pdm>;
codec {
@@ -357,6 +375,8 @@
eth_phy0: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
eee-broken-1000t;
};
};
@@ -444,7 +464,8 @@
bus-width = <4>;
cap-sd-highspeed;
- max-frequency = <100000000>;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
non-removable;
disable-wp;
@@ -461,15 +482,14 @@
/* emmc storage */
&sd_emmc_c {
- status = "disabled";
- pinctrl-0 = <&emmc_pins>;
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
pinctrl-1 = <&emmc_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <8>;
- cap-sd-highspeed;
cap-mmc-highspeed;
- max-frequency = <180000000>;
+ max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
@@ -481,6 +501,12 @@
vqmmc-supply = <&vddio_boot>;
};
+&spdifin {
+ pinctrl-0 = <&spdif_in_a19_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
&spdifout {
pinctrl-0 = <&spdif_out_a20_pins>;
pinctrl-names = "default";
@@ -543,8 +569,14 @@
&uart_A {
status = "okay";
- pinctrl-0 = <&uart_a_pins>;
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_21 GPIO_ACTIVE_HIGH>;
+ };
};
&uart_AO {
@@ -20,7 +20,7 @@
#address-cells = <2>;
#size-cells = <2>;
- tdmif_a: audio-controller@0 {
+ tdmif_a: audio-controller-0 {
compatible = "amlogic,axg-tdm-iface";
#sound-dai-cells = <0>;
sound-name-prefix = "TDM_A";
@@ -31,7 +31,7 @@
status = "disabled";
};
- tdmif_b: audio-controller@1 {
+ tdmif_b: audio-controller-1 {
compatible = "amlogic,axg-tdm-iface";
#sound-dai-cells = <0>;
sound-name-prefix = "TDM_B";
@@ -42,7 +42,7 @@
status = "disabled";
};
- tdmif_c: audio-controller@2 {
+ tdmif_c: audio-controller-2 {
compatible = "amlogic,axg-tdm-iface";
#sound-dai-cells = <0>;
sound-name-prefix = "TDM_C";
@@ -53,13 +53,6 @@
status = "disabled";
};
- ao_alt_xtal: ao_alt_xtal-clk {
- compatible = "fixed-clock";
- clock-frequency = <32000000>;
- clock-output-names = "ao_alt_xtal";
- #clock-cells = <0>;
- };
-
arm-pmu {
compatible = "arm,cortex-a53-pmu";
interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
@@ -75,34 +68,38 @@
cpu0: cpu@0 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x0>;
enable-method = "psci";
next-level-cache = <&l2>;
+ clocks = <&scpi_dvfs 0>;
};
cpu1: cpu@1 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x1>;
enable-method = "psci";
next-level-cache = <&l2>;
+ clocks = <&scpi_dvfs 0>;
};
cpu2: cpu@2 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x2>;
enable-method = "psci";
next-level-cache = <&l2>;
+ clocks = <&scpi_dvfs 0>;
};
cpu3: cpu@3 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x3>;
enable-method = "psci";
next-level-cache = <&l2>;
+ clocks = <&scpi_dvfs 0>;
};
l2: l2-cache0 {
@@ -110,6 +107,19 @@
};
};
+ sm: secure-monitor {
+ compatible = "amlogic,meson-gxbb-sm";
+ };
+
+ efuse: efuse {
+ compatible = "amlogic,meson-gxbb-efuse";
+ clocks = <&clkc CLKID_EFUSE>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ read-only;
+ secure-monitor = <&sm>;
+ };
+
psci {
compatible = "arm,psci-1.0";
method = "smc";
@@ -133,6 +143,28 @@
};
};
+ scpi {
+ compatible = "arm,scpi-pre-1.0";
+ mboxes = <&mailbox 1 &mailbox 2>;
+ shmem = <&cpu_scp_lpri &cpu_scp_hpri>;
+
+ scpi_clocks: clocks {
+ compatible = "arm,scpi-clocks";
+
+ scpi_dvfs: clock-controller {
+ compatible = "arm,scpi-dvfs-clocks";
+ #clock-cells = <1>;
+ clock-indices = <0>;
+ clock-output-names = "vcpu";
+ };
+ };
+
+ scpi_sensors: sensors {
+ compatible = "amlogic,meson-gxbb-scpi-sensors";
+ #thermal-sensor-cells = <1>;
+ };
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <2>;
@@ -140,15 +172,19 @@
ranges;
ethmac: ethernet@ff3f0000 {
- compatible = "amlogic,meson-axg-dwmac", "snps,dwmac";
- reg = <0x0 0xff3f0000 0x0 0x10000
- 0x0 0xff634540 0x0 0x8>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
+ compatible = "amlogic,meson-axg-dwmac",
+ "snps,dwmac-3.70a",
+ "snps,dwmac";
+ reg = <0x0 0xff3f0000 0x0 0x10000>,
+ <0x0 0xff634540 0x0 0x8>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
clocks = <&clkc CLKID_ETH>,
<&clkc CLKID_FCLK_DIV2>,
<&clkc CLKID_MPLL2>;
clock-names = "stmmaceth", "clkin0", "clkin1";
+ rx-fifo-depth = <4096>;
+ tx-fifo-depth = <2048>;
status = "disabled";
};
@@ -200,6 +236,7 @@
groups = "i2c0_sck",
"i2c0_sda";
function = "i2c0";
+ bias-disable;
};
};
@@ -208,6 +245,7 @@
groups = "i2c1_sck_x",
"i2c1_sda_x";
function = "i2c1";
+ bias-disable;
};
};
@@ -216,6 +254,7 @@
groups = "i2c1_sck_z",
"i2c1_sda_z";
function = "i2c1";
+ bias-disable;
};
};
@@ -224,6 +263,7 @@
groups = "i2c2_sck_a",
"i2c2_sda_a";
function = "i2c2";
+ bias-disable;
};
};
@@ -232,6 +272,7 @@
groups = "i2c2_sck_x",
"i2c2_sda_x";
function = "i2c2";
+ bias-disable;
};
};
@@ -240,6 +281,7 @@
groups = "i2c3_sda_a6",
"i2c3_sck_a7";
function = "i2c3";
+ bias-disable;
};
};
@@ -248,6 +290,7 @@
groups = "i2c3_sda_a12",
"i2c3_sck_a13";
function = "i2c3";
+ bias-disable;
};
};
@@ -256,11 +299,12 @@
groups = "i2c3_sda_a19",
"i2c3_sck_a20";
function = "i2c3";
+ bias-disable;
};
};
emmc_pins: emmc {
- mux {
+ mux-0 {
groups = "emmc_nand_d0",
"emmc_nand_d1",
"emmc_nand_d2",
@@ -269,10 +313,23 @@
"emmc_nand_d5",
"emmc_nand_d6",
"emmc_nand_d7",
- "emmc_clk",
- "emmc_cmd",
- "emmc_ds";
+ "emmc_cmd";
+ function = "emmc";
+ bias-pull-up;
+ };
+
+ mux-1 {
+ groups = "emmc_clk";
function = "emmc";
+ bias-disable;
+ };
+ };
+
+ emmc_ds_pins: emmc_ds {
+ mux {
+ groups = "emmc_ds";
+ function = "emmc";
+ bias-pull-down;
};
};
@@ -280,9 +337,6 @@
mux {
groups = "BOOT_8";
function = "gpio_periphs";
- };
- cfg-pull-down {
- pins = "BOOT_8";
bias-pull-down;
};
};
@@ -304,6 +358,7 @@
"eth_txd2_rgmii",
"eth_txd3_rgmii";
function = "eth";
+ bias-disable;
};
};
@@ -324,6 +379,7 @@
"eth_txd2_rgmii",
"eth_txd3_rgmii";
function = "eth";
+ bias-disable;
};
};
@@ -339,6 +395,7 @@
"eth_txd0_x",
"eth_txd1_x";
function = "eth";
+ bias-disable;
};
};
@@ -354,6 +411,7 @@
"eth_txd0_y",
"eth_txd1_y";
function = "eth";
+ bias-disable;
};
};
@@ -361,6 +419,7 @@
mux {
groups = "mclk_b";
function = "mclk_b";
+ bias-disable;
};
};
@@ -368,6 +427,7 @@
mux {
groups = "mclk_c";
function = "mclk_c";
+ bias-disable;
};
};
@@ -375,6 +435,7 @@
mux {
groups = "pdm_dclk_a14";
function = "pdm";
+ bias-disable;
};
};
@@ -382,6 +443,7 @@
mux {
groups = "pdm_dclk_a19";
function = "pdm";
+ bias-disable;
};
};
@@ -389,6 +451,7 @@
mux {
groups = "pdm_din0";
function = "pdm";
+ bias-disable;
};
};
@@ -396,6 +459,7 @@
mux {
groups = "pdm_din1";
function = "pdm";
+ bias-disable;
};
};
@@ -403,6 +467,7 @@
mux {
groups = "pdm_din2";
function = "pdm";
+ bias-disable;
};
};
@@ -410,6 +475,7 @@
mux {
groups = "pdm_din3";
function = "pdm";
+ bias-disable;
};
};
@@ -417,6 +483,7 @@
mux {
groups = "pwm_a_a";
function = "pwm_a";
+ bias-disable;
};
};
@@ -424,6 +491,7 @@
mux {
groups = "pwm_a_x18";
function = "pwm_a";
+ bias-disable;
};
};
@@ -431,6 +499,7 @@
mux {
groups = "pwm_a_x20";
function = "pwm_a";
+ bias-disable;
};
};
@@ -438,6 +507,7 @@
mux {
groups = "pwm_a_z";
function = "pwm_a";
+ bias-disable;
};
};
@@ -445,6 +515,7 @@
mux {
groups = "pwm_b_a";
function = "pwm_b";
+ bias-disable;
};
};
@@ -452,6 +523,7 @@
mux {
groups = "pwm_b_x";
function = "pwm_b";
+ bias-disable;
};
};
@@ -459,6 +531,7 @@
mux {
groups = "pwm_b_z";
function = "pwm_b";
+ bias-disable;
};
};
@@ -466,6 +539,7 @@
mux {
groups = "pwm_c_a";
function = "pwm_c";
+ bias-disable;
};
};
@@ -473,6 +547,7 @@
mux {
groups = "pwm_c_x10";
function = "pwm_c";
+ bias-disable;
};
};
@@ -480,6 +555,7 @@
mux {
groups = "pwm_c_x17";
function = "pwm_c";
+ bias-disable;
};
};
@@ -487,6 +563,7 @@
mux {
groups = "pwm_d_x11";
function = "pwm_d";
+ bias-disable;
};
};
@@ -494,18 +571,25 @@
mux {
groups = "pwm_d_x16";
function = "pwm_d";
+ bias-disable;
};
};
sdio_pins: sdio {
- mux {
+ mux-0 {
groups = "sdio_d0",
"sdio_d1",
"sdio_d2",
"sdio_d3",
- "sdio_cmd",
- "sdio_clk";
+ "sdio_cmd";
+ function = "sdio";
+ bias-pull-up;
+ };
+
+ mux-1 {
+ groups = "sdio_clk";
function = "sdio";
+ bias-disable;
};
};
@@ -513,9 +597,6 @@
mux {
groups = "GPIOX_4";
function = "gpio_periphs";
- };
- cfg-pull-down {
- pins = "GPIOX_4";
bias-pull-down;
};
};
@@ -524,6 +605,7 @@
mux {
groups = "spdif_in_z";
function = "spdif_in";
+ bias-disable;
};
};
@@ -531,6 +613,7 @@
mux {
groups = "spdif_in_a1";
function = "spdif_in";
+ bias-disable;
};
};
@@ -538,6 +621,7 @@
mux {
groups = "spdif_in_a7";
function = "spdif_in";
+ bias-disable;
};
};
@@ -545,6 +629,7 @@
mux {
groups = "spdif_in_a19";
function = "spdif_in";
+ bias-disable;
};
};
@@ -552,6 +637,7 @@
mux {
groups = "spdif_in_a20";
function = "spdif_in";
+ bias-disable;
};
};
@@ -559,6 +645,7 @@
mux {
groups = "spdif_out_a1";
function = "spdif_out";
+ bias-disable;
};
};
@@ -566,6 +653,7 @@
mux {
groups = "spdif_out_a11";
function = "spdif_out";
+ bias-disable;
};
};
@@ -573,6 +661,7 @@
mux {
groups = "spdif_out_a19";
function = "spdif_out";
+ bias-disable;
};
};
@@ -580,6 +669,7 @@
mux {
groups = "spdif_out_a20";
function = "spdif_out";
+ bias-disable;
};
};
@@ -587,6 +677,7 @@
mux {
groups = "spdif_out_z";
function = "spdif_out";
+ bias-disable;
};
};
@@ -596,6 +687,7 @@
"spi0_mosi",
"spi0_clk";
function = "spi0";
+ bias-disable;
};
};
@@ -603,6 +695,7 @@
mux {
groups = "spi0_ss0";
function = "spi0";
+ bias-disable;
};
};
@@ -610,6 +703,7 @@
mux {
groups = "spi0_ss1";
function = "spi0";
+ bias-disable;
};
};
@@ -617,6 +711,7 @@
mux {
groups = "spi0_ss2";
function = "spi0";
+ bias-disable;
};
};
@@ -626,6 +721,7 @@
"spi1_mosi_a",
"spi1_clk_a";
function = "spi1";
+ bias-disable;
};
};
@@ -633,6 +729,7 @@
mux {
groups = "spi1_ss0_a";
function = "spi1";
+ bias-disable;
};
};
@@ -640,6 +737,7 @@
mux {
groups = "spi1_ss1";
function = "spi1";
+ bias-disable;
};
};
@@ -649,6 +747,7 @@
"spi1_mosi_x",
"spi1_clk_x";
function = "spi1";
+ bias-disable;
};
};
@@ -656,6 +755,7 @@
mux {
groups = "spi1_ss0_x";
function = "spi1";
+ bias-disable;
};
};
@@ -663,6 +763,7 @@
mux {
groups = "tdma_din0";
function = "tdma";
+ bias-disable;
};
};
@@ -670,6 +771,7 @@
mux {
groups = "tdma_dout0_x14";
function = "tdma";
+ bias-disable;
};
};
@@ -677,6 +779,7 @@
mux {
groups = "tdma_dout0_x15";
function = "tdma";
+ bias-disable;
};
};
@@ -684,6 +787,7 @@
mux {
groups = "tdma_dout1";
function = "tdma";
+ bias-disable;
};
};
@@ -691,6 +795,7 @@
mux {
groups = "tdma_din1";
function = "tdma";
+ bias-disable;
};
};
@@ -698,6 +803,7 @@
mux {
groups = "tdma_fs";
function = "tdma";
+ bias-disable;
};
};
@@ -705,6 +811,7 @@
mux {
groups = "tdma_fs_slv";
function = "tdma";
+ bias-disable;
};
};
@@ -712,6 +819,7 @@
mux {
groups = "tdma_sclk";
function = "tdma";
+ bias-disable;
};
};
@@ -719,6 +827,7 @@
mux {
groups = "tdma_sclk_slv";
function = "tdma";
+ bias-disable;
};
};
@@ -726,6 +835,7 @@
mux {
groups = "tdmb_din0";
function = "tdmb";
+ bias-disable;
};
};
@@ -733,6 +843,7 @@
mux {
groups = "tdmb_din1";
function = "tdmb";
+ bias-disable;
};
};
@@ -740,6 +851,7 @@
mux {
groups = "tdmb_din2";
function = "tdmb";
+ bias-disable;
};
};
@@ -747,6 +859,7 @@
mux {
groups = "tdmb_din3";
function = "tdmb";
+ bias-disable;
};
};
@@ -754,6 +867,7 @@
mux {
groups = "tdmb_dout0";
function = "tdmb";
+ bias-disable;
};
};
@@ -761,6 +875,7 @@
mux {
groups = "tdmb_dout1";
function = "tdmb";
+ bias-disable;
};
};
@@ -768,6 +883,7 @@
mux {
groups = "tdmb_dout2";
function = "tdmb";
+ bias-disable;
};
};
@@ -775,6 +891,7 @@
mux {
groups = "tdmb_dout3";
function = "tdmb";
+ bias-disable;
};
};
@@ -782,6 +899,7 @@
mux {
groups = "tdmb_fs";
function = "tdmb";
+ bias-disable;
};
};
@@ -789,6 +907,7 @@
mux {
groups = "tdmb_fs_slv";
function = "tdmb";
+ bias-disable;
};
};
@@ -796,6 +915,7 @@
mux {
groups = "tdmb_sclk";
function = "tdmb";
+ bias-disable;
};
};
@@ -803,6 +923,7 @@
mux {
groups = "tdmb_sclk_slv";
function = "tdmb";
+ bias-disable;
};
};
@@ -810,6 +931,7 @@
mux {
groups = "tdmc_fs";
function = "tdmc";
+ bias-disable;
};
};
@@ -817,6 +939,7 @@
mux {
groups = "tdmc_fs_slv";
function = "tdmc";
+ bias-disable;
};
};
@@ -824,6 +947,7 @@
mux {
groups = "tdmc_sclk";
function = "tdmc";
+ bias-disable;
};
};
@@ -831,6 +955,7 @@
mux {
groups = "tdmc_sclk_slv";
function = "tdmc";
+ bias-disable;
};
};
@@ -838,6 +963,7 @@
mux {
groups = "tdmc_din0";
function = "tdmc";
+ bias-disable;
};
};
@@ -845,6 +971,7 @@
mux {
groups = "tdmc_din1";
function = "tdmc";
+ bias-disable;
};
};
@@ -852,6 +979,7 @@
mux {
groups = "tdmc_din2";
function = "tdmc";
+ bias-disable;
};
};
@@ -859,6 +987,7 @@
mux {
groups = "tdmc_din3";
function = "tdmc";
+ bias-disable;
};
};
@@ -866,6 +995,7 @@
mux {
groups = "tdmc_dout0";
function = "tdmc";
+ bias-disable;
};
};
@@ -873,6 +1003,7 @@
mux {
groups = "tdmc_dout1";
function = "tdmc";
+ bias-disable;
};
};
@@ -880,6 +1011,7 @@
mux {
groups = "tdmc_dout2";
function = "tdmc";
+ bias-disable;
};
};
@@ -887,6 +1019,7 @@
mux {
groups = "tdmc_dout3";
function = "tdmc";
+ bias-disable;
};
};
@@ -895,6 +1028,7 @@
groups = "uart_tx_a",
"uart_rx_a";
function = "uart_a";
+ bias-disable;
};
};
@@ -903,6 +1037,7 @@
groups = "uart_cts_a",
"uart_rts_a";
function = "uart_a";
+ bias-disable;
};
};
@@ -911,6 +1046,7 @@
groups = "uart_tx_b_x",
"uart_rx_b_x";
function = "uart_b";
+ bias-disable;
};
};
@@ -919,6 +1055,7 @@
groups = "uart_cts_b_x",
"uart_rts_b_x";
function = "uart_b";
+ bias-disable;
};
};
@@ -927,6 +1064,7 @@
groups = "uart_tx_b_z",
"uart_rx_b_z";
function = "uart_b";
+ bias-disable;
};
};
@@ -935,6 +1073,7 @@
groups = "uart_cts_b_z",
"uart_rts_b_z";
function = "uart_b";
+ bias-disable;
};
};
@@ -943,6 +1082,7 @@
groups = "uart_ao_tx_b_z",
"uart_ao_rx_b_z";
function = "uart_ao_b_z";
+ bias-disable;
};
};
@@ -951,6 +1091,7 @@
groups = "uart_ao_cts_b_z",
"uart_ao_rts_b_z";
function = "uart_ao_b_z";
+ bias-disable;
};
};
};
@@ -971,13 +1112,15 @@
clkc: clock-controller {
compatible = "amlogic,axg-clkc";
#clock-cells = <1>;
+ clocks = <&xtal>;
+ clock-names = "xtal";
};
};
};
- mailbox: mailbox@ff63dc00 {
- compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
- reg = <0 0xff63dc00 0 0x400>;
+ mailbox: mailbox@ff63c404 {
+ compatible = "amlogic,meson-gxbb-mhu";
+ reg = <0 0xff63c404 0 0x4c>;
interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 209 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 210 IRQ_TYPE_EDGE_RISING>;
@@ -1020,67 +1163,73 @@
toddr_a: audio-controller@100 {
compatible = "amlogic,axg-toddr";
- reg = <0x0 0x100 0x0 0x1c>;
+ reg = <0x0 0x100 0x0 0x2c>;
#sound-dai-cells = <0>;
sound-name-prefix = "TODDR_A";
interrupts = <GIC_SPI 84 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc_audio AUD_CLKID_TODDR_A>;
resets = <&arb AXG_ARB_TODDR_A>;
+ amlogic,fifo-depth = <512>;
status = "disabled";
};
toddr_b: audio-controller@140 {
compatible = "amlogic,axg-toddr";
- reg = <0x0 0x140 0x0 0x1c>;
+ reg = <0x0 0x140 0x0 0x2c>;
#sound-dai-cells = <0>;
sound-name-prefix = "TODDR_B";
interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc_audio AUD_CLKID_TODDR_B>;
resets = <&arb AXG_ARB_TODDR_B>;
+ amlogic,fifo-depth = <256>;
status = "disabled";
};
toddr_c: audio-controller@180 {
compatible = "amlogic,axg-toddr";
- reg = <0x0 0x180 0x0 0x1c>;
+ reg = <0x0 0x180 0x0 0x2c>;
#sound-dai-cells = <0>;
sound-name-prefix = "TODDR_C";
interrupts = <GIC_SPI 86 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc_audio AUD_CLKID_TODDR_C>;
resets = <&arb AXG_ARB_TODDR_C>;
+ amlogic,fifo-depth = <256>;
status = "disabled";
};
frddr_a: audio-controller@1c0 {
compatible = "amlogic,axg-frddr";
- reg = <0x0 0x1c0 0x0 0x1c>;
+ reg = <0x0 0x1c0 0x0 0x2c>;
#sound-dai-cells = <0>;
sound-name-prefix = "FRDDR_A";
interrupts = <GIC_SPI 88 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc_audio AUD_CLKID_FRDDR_A>;
resets = <&arb AXG_ARB_FRDDR_A>;
+ amlogic,fifo-depth = <512>;
status = "disabled";
};
frddr_b: audio-controller@200 {
compatible = "amlogic,axg-frddr";
- reg = <0x0 0x200 0x0 0x1c>;
+ reg = <0x0 0x200 0x0 0x2c>;
#sound-dai-cells = <0>;
sound-name-prefix = "FRDDR_B";
interrupts = <GIC_SPI 89 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc_audio AUD_CLKID_FRDDR_B>;
resets = <&arb AXG_ARB_FRDDR_B>;
+ amlogic,fifo-depth = <256>;
status = "disabled";
};
frddr_c: audio-controller@240 {
compatible = "amlogic,axg-frddr";
- reg = <0x0 0x240 0x0 0x1c>;
+ reg = <0x0 0x240 0x0 0x2c>;
#sound-dai-cells = <0>;
sound-name-prefix = "FRDDR_C";
interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
clocks = <&clkc_audio AUD_CLKID_FRDDR_C>;
resets = <&arb AXG_ARB_FRDDR_C>;
+ amlogic,fifo-depth = <256>;
status = "disabled";
};
@@ -1147,6 +1296,18 @@
status = "disabled";
};
+ spdifin: audio-controller@400 {
+ compatible = "amlogic,axg-spdifin";
+ reg = <0x0 0x400 0x0 0x30>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFIN";
+ interrupts = <GIC_SPI 87 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_SPDIFIN>,
+ <&clkc_audio AUD_CLKID_SPDIFIN_CLK>;
+ clock-names = "pclk", "refclk";
+ status = "disabled";
+ };
+
spdifout: audio-controller@480 {
compatible = "amlogic,axg-spdifout";
reg = <0x0 0x480 0x0 0x50>;
@@ -1216,6 +1377,8 @@
compatible = "amlogic,meson-axg-aoclkc";
#clock-cells = <1>;
#reset-cells = <1>;
+ clocks = <&xtal>, <&clkc CLKID_CLK81>;
+ clock-names = "xtal", "mpeg-clk";
};
};
@@ -1239,6 +1402,7 @@
mux {
groups = "i2c_ao_sck_4";
function = "i2c_ao";
+ bias-disable;
};
};
@@ -1246,6 +1410,7 @@
mux {
groups = "i2c_ao_sck_8";
function = "i2c_ao";
+ bias-disable;
};
};
@@ -1253,6 +1418,7 @@
mux {
groups = "i2c_ao_sck_10";
function = "i2c_ao";
+ bias-disable;
};
};
@@ -1260,6 +1426,7 @@
mux {
groups = "i2c_ao_sda_5";
function = "i2c_ao";
+ bias-disable;
};
};
@@ -1267,6 +1434,7 @@
mux {
groups = "i2c_ao_sda_9";
function = "i2c_ao";
+ bias-disable;
};
};
@@ -1274,6 +1442,7 @@
mux {
groups = "i2c_ao_sda_11";
function = "i2c_ao";
+ bias-disable;
};
};
@@ -1281,6 +1450,7 @@
mux {
groups = "remote_input_ao";
function = "remote_input_ao";
+ bias-disable;
};
};
@@ -1289,6 +1459,7 @@
groups = "uart_ao_tx_a",
"uart_ao_rx_a";
function = "uart_ao_a";
+ bias-disable;
};
};
@@ -1297,6 +1468,7 @@
groups = "uart_ao_cts_a",
"uart_ao_rts_a";
function = "uart_ao_a";
+ bias-disable;
};
};
@@ -1305,6 +1477,7 @@
groups = "uart_ao_tx_b",
"uart_ao_rx_b";
function = "uart_ao_b";
+ bias-disable;
};
};
@@ -1313,6 +1486,7 @@
groups = "uart_ao_cts_b",
"uart_ao_rts_b";
function = "uart_ao_b";
+ bias-disable;
};
};
};
@@ -1414,12 +1588,18 @@
};
gpio_intc: interrupt-controller@f080 {
- compatible = "amlogic,meson-gpio-intc";
+ compatible = "amlogic,meson-axg-gpio-intc",
+ "amlogic,meson-gpio-intc";
reg = <0x0 0xf080 0x0 0x10>;
interrupt-controller;
#interrupt-cells = <2>;
amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>;
- status = "disabled";
+ };
+
+ watchdog@f0d0 {
+ compatible = "amlogic,meson-gxbb-wdt";
+ reg = <0x0 0xf0d0 0x0 0x10>;
+ clocks = <&xtal>;
};
pwm_ab: pwm@1b000 {
@@ -1458,6 +1638,11 @@
status = "disabled";
};
+ clk_msr: clock-measure@18000 {
+ compatible = "amlogic,meson-axg-clk-measure";
+ reg = <0x0 0x18000 0x0 0x10>;
+ };
+
i2c3: i2c@1c000 {
compatible = "amlogic,meson-axg-i2c";
reg = <0x0 0x1c000 0x0 0x20>;
@@ -1556,12 +1741,12 @@
#size-cells = <1>;
ranges = <0 0x0 0xfffc0000 0x20000>;
- cpu_scp_lpri: scp-shmem@0 {
+ cpu_scp_lpri: scp-shmem@13000 {
compatible = "amlogic,meson-axg-scp-shmem";
reg = <0x13000 0x400>;
};
- cpu_scp_hpri: scp-shmem@200 {
+ cpu_scp_hpri: scp-shmem@13400 {
compatible = "amlogic,meson-axg-scp-shmem";
reg = <0x13400 0x400>;
};
@@ -5,51 +5,42 @@
#include <dt-bindings/phy/phy.h>
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clock/axg-audio-clkc.h>
#include <dt-bindings/clock/g12a-clkc.h>
#include <dt-bindings/clock/g12a-aoclkc.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
-#include <dt-bindings/reset/amlogic,meson-g12a-audio-reset.h>
#include <dt-bindings/reset/amlogic,meson-g12a-reset.h>
+#include <dt-bindings/thermal/thermal.h>
/ {
interrupt-parent = <&gic>;
#address-cells = <2>;
#size-cells = <2>;
- tdmif_a: audio-controller-0 {
- compatible = "amlogic,axg-tdm-iface";
- #sound-dai-cells = <0>;
- sound-name-prefix = "TDM_A";
- clocks = <&clkc_audio AUD_CLKID_MST_A_MCLK>,
- <&clkc_audio AUD_CLKID_MST_A_SCLK>,
- <&clkc_audio AUD_CLKID_MST_A_LRCLK>;
- clock-names = "mclk", "sclk", "lrclk";
- status = "disabled";
- };
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
- tdmif_b: audio-controller-1 {
- compatible = "amlogic,axg-tdm-iface";
- #sound-dai-cells = <0>;
- sound-name-prefix = "TDM_B";
- clocks = <&clkc_audio AUD_CLKID_MST_B_MCLK>,
- <&clkc_audio AUD_CLKID_MST_B_SCLK>,
- <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
- clock-names = "mclk", "sclk", "lrclk";
- status = "disabled";
- };
+ simplefb_cvbs: framebuffer-cvbs {
+ compatible = "amlogic,simple-framebuffer",
+ "simple-framebuffer";
+ amlogic,pipeline = "vpu-cvbs";
+ clocks = <&clkc CLKID_HDMI>,
+ <&clkc CLKID_HTX_PCLK>,
+ <&clkc CLKID_VPU_INTR>;
+ status = "disabled";
+ };
- tdmif_c: audio-controller-2 {
- compatible = "amlogic,axg-tdm-iface";
- #sound-dai-cells = <0>;
- sound-name-prefix = "TDM_C";
- clocks = <&clkc_audio AUD_CLKID_MST_C_MCLK>,
- <&clkc_audio AUD_CLKID_MST_C_SCLK>,
- <&clkc_audio AUD_CLKID_MST_C_LRCLK>;
- clock-names = "mclk", "sclk", "lrclk";
- status = "disabled";
+ simplefb_hdmi: framebuffer-hdmi {
+ compatible = "amlogic,simple-framebuffer",
+ "simple-framebuffer";
+ amlogic,pipeline = "vpu-hdmi";
+ clocks = <&clkc CLKID_HDMI>,
+ <&clkc CLKID_HTX_PCLK>,
+ <&clkc CLKID_VPU_INTR>;
+ status = "disabled";
+ };
};
efuse: efuse {
@@ -58,6 +49,7 @@
#address-cells = <1>;
#size-cells = <1>;
read-only;
+ secure-monitor = <&sm>;
};
psci {
@@ -95,6 +87,94 @@
#size-cells = <2>;
ranges;
+ pcie: pcie@fc000000 {
+ compatible = "amlogic,g12a-pcie", "snps,dw-pcie";
+ reg = <0x0 0xfc000000 0x0 0x400000
+ 0x0 0xff648000 0x0 0x2000
+ 0x0 0xfc400000 0x0 0x200000>;
+ reg-names = "elbi", "cfg", "config";
+ interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+ bus-range = <0x0 0xff>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x81000000 0 0 0x0 0xfc600000 0 0x00100000
+ 0x82000000 0 0xfc700000 0x0 0xfc700000 0 0x1900000>;
+
+ clocks = <&clkc CLKID_PCIE_PHY
+ &clkc CLKID_PCIE_COMB
+ &clkc CLKID_PCIE_PLL>;
+ clock-names = "general",
+ "pclk",
+ "port";
+ resets = <&reset RESET_PCIE_CTRL_A>,
+ <&reset RESET_PCIE_APB>;
+ reset-names = "port",
+ "apb";
+ num-lanes = <1>;
+ phys = <&usb3_pcie_phy PHY_TYPE_PCIE>;
+ phy-names = "pcie";
+ status = "disabled";
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&cpu_temp>;
+
+ trips {
+ cpu_passive: cpu-passive {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ cpu_hot: cpu-hot {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "hot";
+ };
+
+ cpu_critical: cpu-critical {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ ddr_thermal: ddr-thermal {
+ polling-delay = <1000>;
+ polling-delay-passive = <100>;
+ thermal-sensors = <&ddr_temp>;
+
+ trips {
+ ddr_passive: ddr-passive {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ ddr_critical: ddr-critical {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&ddr_passive>;
+ cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
ethmac: ethernet@ff3f0000 {
compatible = "amlogic,meson-axg-dwmac",
"snps,dwmac-3.70a",
@@ -1356,6 +1436,26 @@
};
};
+ cpu_temp: temperature-sensor@34800 {
+ compatible = "amlogic,g12a-cpu-thermal",
+ "amlogic,g12a-thermal";
+ reg = <0x0 0x34800 0x0 0x50>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_TS>;
+ #thermal-sensor-cells = <0>;
+ amlogic,ao-secure = <&sec_AO>;
+ };
+
+ ddr_temp: temperature-sensor@34c00 {
+ compatible = "amlogic,g12a-ddr-thermal",
+ "amlogic,g12a-thermal";
+ reg = <0x0 0x34c00 0x0 0x50>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_TS>;
+ #thermal-sensor-cells = <0>;
+ amlogic,ao-secure = <&sec_AO>;
+ };
+
usb2_phy0: phy@36000 {
compatible = "amlogic,g12a-usb2-phy";
reg = <0x0 0x36000 0x0 0x2000>;
@@ -1457,290 +1557,6 @@
};
};
- pdm: audio-controller@40000 {
- compatible = "amlogic,g12a-pdm",
- "amlogic,axg-pdm";
- reg = <0x0 0x40000 0x0 0x34>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "PDM";
- clocks = <&clkc_audio AUD_CLKID_PDM>,
- <&clkc_audio AUD_CLKID_PDM_DCLK>,
- <&clkc_audio AUD_CLKID_PDM_SYSCLK>;
- clock-names = "pclk", "dclk", "sysclk";
- status = "disabled";
- };
-
- audio: bus@42000 {
- compatible = "simple-bus";
- reg = <0x0 0x42000 0x0 0x2000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0x42000 0x0 0x2000>;
-
- clkc_audio: clock-controller@0 {
- status = "disabled";
- compatible = "amlogic,g12a-audio-clkc";
- reg = <0x0 0x0 0x0 0xb4>;
- #clock-cells = <1>;
- #reset-cells = <1>;
-
- clocks = <&clkc CLKID_AUDIO>,
- <&clkc CLKID_MPLL0>,
- <&clkc CLKID_MPLL1>,
- <&clkc CLKID_MPLL2>,
- <&clkc CLKID_MPLL3>,
- <&clkc CLKID_HIFI_PLL>,
- <&clkc CLKID_FCLK_DIV3>,
- <&clkc CLKID_FCLK_DIV4>,
- <&clkc CLKID_GP0_PLL>;
- clock-names = "pclk",
- "mst_in0",
- "mst_in1",
- "mst_in2",
- "mst_in3",
- "mst_in4",
- "mst_in5",
- "mst_in6",
- "mst_in7";
-
- resets = <&reset RESET_AUDIO>;
- };
-
- toddr_a: audio-controller@100 {
- compatible = "amlogic,g12a-toddr",
- "amlogic,axg-toddr";
- reg = <0x0 0x100 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "TODDR_A";
- interrupts = <GIC_SPI 148 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_TODDR_A>;
- resets = <&arb AXG_ARB_TODDR_A>;
- status = "disabled";
- };
-
- toddr_b: audio-controller@140 {
- compatible = "amlogic,g12a-toddr",
- "amlogic,axg-toddr";
- reg = <0x0 0x140 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "TODDR_B";
- interrupts = <GIC_SPI 149 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_TODDR_B>;
- resets = <&arb AXG_ARB_TODDR_B>;
- status = "disabled";
- };
-
- toddr_c: audio-controller@180 {
- compatible = "amlogic,g12a-toddr",
- "amlogic,axg-toddr";
- reg = <0x0 0x180 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "TODDR_C";
- interrupts = <GIC_SPI 150 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_TODDR_C>;
- resets = <&arb AXG_ARB_TODDR_C>;
- status = "disabled";
- };
-
- frddr_a: audio-controller@1c0 {
- compatible = "amlogic,g12a-frddr",
- "amlogic,axg-frddr";
- reg = <0x0 0x1c0 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "FRDDR_A";
- interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_FRDDR_A>;
- resets = <&arb AXG_ARB_FRDDR_A>;
- status = "disabled";
- };
-
- frddr_b: audio-controller@200 {
- compatible = "amlogic,g12a-frddr",
- "amlogic,axg-frddr";
- reg = <0x0 0x200 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "FRDDR_B";
- interrupts = <GIC_SPI 153 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_FRDDR_B>;
- resets = <&arb AXG_ARB_FRDDR_B>;
- status = "disabled";
- };
-
- frddr_c: audio-controller@240 {
- compatible = "amlogic,g12a-frddr",
- "amlogic,axg-frddr";
- reg = <0x0 0x240 0x0 0x1c>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "FRDDR_C";
- interrupts = <GIC_SPI 154 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_FRDDR_C>;
- resets = <&arb AXG_ARB_FRDDR_C>;
- status = "disabled";
- };
-
- arb: reset-controller@280 {
- status = "disabled";
- compatible = "amlogic,meson-axg-audio-arb";
- reg = <0x0 0x280 0x0 0x4>;
- #reset-cells = <1>;
- clocks = <&clkc_audio AUD_CLKID_DDR_ARB>;
- };
-
- tdmin_a: audio-controller@300 {
- compatible = "amlogic,g12a-tdmin",
- "amlogic,axg-tdmin";
- reg = <0x0 0x300 0x0 0x40>;
- sound-name-prefix = "TDMIN_A";
- resets = <&clkc_audio AUD_RESET_TDMIN_A>;
- clocks = <&clkc_audio AUD_CLKID_TDMIN_A>,
- <&clkc_audio AUD_CLKID_TDMIN_A_SCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_A_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmin_b: audio-controller@340 {
- compatible = "amlogic,g12a-tdmin",
- "amlogic,axg-tdmin";
- reg = <0x0 0x340 0x0 0x40>;
- sound-name-prefix = "TDMIN_B";
- resets = <&clkc_audio AUD_RESET_TDMIN_B>;
- clocks = <&clkc_audio AUD_CLKID_TDMIN_B>,
- <&clkc_audio AUD_CLKID_TDMIN_B_SCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_B_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmin_c: audio-controller@380 {
- compatible = "amlogic,g12a-tdmin",
- "amlogic,axg-tdmin";
- reg = <0x0 0x380 0x0 0x40>;
- sound-name-prefix = "TDMIN_C";
- resets = <&clkc_audio AUD_RESET_TDMIN_C>;
- clocks = <&clkc_audio AUD_CLKID_TDMIN_C>,
- <&clkc_audio AUD_CLKID_TDMIN_C_SCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_C_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmin_lb: audio-controller@3c0 {
- compatible = "amlogic,g12a-tdmin",
- "amlogic,axg-tdmin";
- reg = <0x0 0x3c0 0x0 0x40>;
- sound-name-prefix = "TDMIN_LB";
- resets = <&clkc_audio AUD_RESET_TDMIN_LB>;
- clocks = <&clkc_audio AUD_CLKID_TDMIN_LB>,
- <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- spdifin: audio-controller@400 {
- compatible = "amlogic,g12a-spdifin",
- "amlogic,axg-spdifin";
- reg = <0x0 0x400 0x0 0x30>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "SPDIFIN";
- interrupts = <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc_audio AUD_CLKID_SPDIFIN>,
- <&clkc_audio AUD_CLKID_SPDIFIN_CLK>;
- clock-names = "pclk", "refclk";
- status = "disabled";
- };
-
- spdifout: audio-controller@480 {
- compatible = "amlogic,g12a-spdifout",
- "amlogic,axg-spdifout";
- reg = <0x0 0x480 0x0 0x50>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "SPDIFOUT";
- clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>,
- <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>;
- clock-names = "pclk", "mclk";
- status = "disabled";
- };
-
- tdmout_a: audio-controller@500 {
- compatible = "amlogic,g12a-tdmout";
- reg = <0x0 0x500 0x0 0x40>;
- sound-name-prefix = "TDMOUT_A";
- resets = <&clkc_audio AUD_RESET_TDMOUT_A>;
- clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>,
- <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmout_b: audio-controller@540 {
- compatible = "amlogic,g12a-tdmout";
- reg = <0x0 0x540 0x0 0x40>;
- sound-name-prefix = "TDMOUT_B";
- resets = <&clkc_audio AUD_RESET_TDMOUT_B>;
- clocks = <&clkc_audio AUD_CLKID_TDMOUT_B>,
- <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- tdmout_c: audio-controller@580 {
- compatible = "amlogic,g12a-tdmout";
- reg = <0x0 0x580 0x0 0x40>;
- sound-name-prefix = "TDMOUT_C";
- resets = <&clkc_audio AUD_RESET_TDMOUT_C>;
- clocks = <&clkc_audio AUD_CLKID_TDMOUT_C>,
- <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK_SEL>,
- <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>,
- <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>;
- clock-names = "pclk", "sclk", "sclk_sel",
- "lrclk", "lrclk_sel";
- status = "disabled";
- };
-
- spdifout_b: audio-controller@680 {
- compatible = "amlogic,g12a-spdifout",
- "amlogic,axg-spdifout";
- reg = <0x0 0x680 0x0 0x50>;
- #sound-dai-cells = <0>;
- sound-name-prefix = "SPDIFOUT_B";
- clocks = <&clkc_audio AUD_CLKID_SPDIFOUT_B>,
- <&clkc_audio AUD_CLKID_SPDIFOUT_B_CLK>;
- clock-names = "pclk", "mclk";
- status = "disabled";
- };
-
- tohdmitx: audio-controller@744 {
- compatible = "amlogic,g12a-tohdmitx";
- reg = <0x0 0x744 0x0 0x4>;
- #sound-dai-cells = <1>;
- sound-name-prefix = "TOHDMITX";
- status = "disabled";
- };
- };
-
usb3_pcie_phy: phy@46000 {
compatible = "amlogic,g12a-usb3-pcie-phy";
reg = <0x0 0x46000 0x0 0x2000>;
@@ -2152,6 +1968,29 @@
};
};
+ vdec: video-decoder@ff620000 {
+ compatible = "amlogic,g12a-vdec";
+ reg = <0x0 0xff620000 0x0 0x10000>,
+ <0x0 0xffd0e180 0x0 0xe4>;
+ reg-names = "dos", "esparser";
+ interrupts = <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "vdec", "esparser";
+
+ amlogic,ao-sysctrl = <&rti>;
+ amlogic,canvas = <&canvas>;
+
+ clocks = <&clkc CLKID_PARSER>,
+ <&clkc CLKID_DOS>,
+ <&clkc CLKID_VDEC_1>,
+ <&clkc CLKID_VDEC_HEVC>,
+ <&clkc CLKID_VDEC_HEVCF>;
+ clock-names = "dos_parser", "dos", "vdec_1",
+ "vdec_hevc", "vdec_hevcf";
+ resets = <&reset RESET_PARSER>;
+ reset-names = "esparser";
+ };
+
vpu: vpu@ff900000 {
compatible = "amlogic,meson-g12a-vpu";
reg = <0x0 0xff900000 0x0 0x100000>,
@@ -2388,10 +2227,10 @@
compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost";
reg = <0x0 0xffe40000 0x0 0x40000>;
interrupt-parent = <&gic>;
- interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+ interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "gpu", "mmu", "job";
+ <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "job", "mmu", "gpu";
clocks = <&clkc CLKID_MALI>;
resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>;
@@ -2409,6 +2248,7 @@
assigned-clock-rates = <0>, /* Do Nothing */
<800000000>,
<0>; /* Do Nothing */
+ #cooling-cells = <2>;
};
};
new file mode 100644
@@ -0,0 +1,398 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+#include "meson-g12-common.dtsi"
+#include <dt-bindings/clock/axg-audio-clkc.h>
+#include <dt-bindings/power/meson-g12a-power.h>
+#include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
+#include <dt-bindings/reset/amlogic,meson-g12a-audio-reset.h>
+
+/ {
+ tdmif_a: audio-controller-0 {
+ compatible = "amlogic,axg-tdm-iface";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TDM_A";
+ clocks = <&clkc_audio AUD_CLKID_MST_A_MCLK>,
+ <&clkc_audio AUD_CLKID_MST_A_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_A_LRCLK>;
+ clock-names = "mclk", "sclk", "lrclk";
+ status = "disabled";
+ };
+
+ tdmif_b: audio-controller-1 {
+ compatible = "amlogic,axg-tdm-iface";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TDM_B";
+ clocks = <&clkc_audio AUD_CLKID_MST_B_MCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
+ clock-names = "mclk", "sclk", "lrclk";
+ status = "disabled";
+ };
+
+ tdmif_c: audio-controller-2 {
+ compatible = "amlogic,axg-tdm-iface";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TDM_C";
+ clocks = <&clkc_audio AUD_CLKID_MST_C_MCLK>,
+ <&clkc_audio AUD_CLKID_MST_C_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_C_LRCLK>;
+ clock-names = "mclk", "sclk", "lrclk";
+ status = "disabled";
+ };
+};
+
+&apb {
+ pdm: audio-controller@40000 {
+ compatible = "amlogic,g12a-pdm",
+ "amlogic,axg-pdm";
+ reg = <0x0 0x40000 0x0 0x34>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "PDM";
+ clocks = <&clkc_audio AUD_CLKID_PDM>,
+ <&clkc_audio AUD_CLKID_PDM_DCLK>,
+ <&clkc_audio AUD_CLKID_PDM_SYSCLK>;
+ clock-names = "pclk", "dclk", "sysclk";
+ status = "disabled";
+ };
+
+ audio: bus@42000 {
+ compatible = "simple-bus";
+ reg = <0x0 0x42000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x42000 0x0 0x2000>;
+
+ clkc_audio: clock-controller@0 {
+ status = "disabled";
+ compatible = "amlogic,g12a-audio-clkc";
+ reg = <0x0 0x0 0x0 0xb4>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+
+ clocks = <&clkc CLKID_AUDIO>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>,
+ <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL3>,
+ <&clkc CLKID_HIFI_PLL>,
+ <&clkc CLKID_FCLK_DIV3>,
+ <&clkc CLKID_FCLK_DIV4>,
+ <&clkc CLKID_GP0_PLL>;
+ clock-names = "pclk",
+ "mst_in0",
+ "mst_in1",
+ "mst_in2",
+ "mst_in3",
+ "mst_in4",
+ "mst_in5",
+ "mst_in6",
+ "mst_in7";
+
+ resets = <&reset RESET_AUDIO>;
+ };
+
+ toddr_a: audio-controller@100 {
+ compatible = "amlogic,g12a-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x100 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_A";
+ interrupts = <GIC_SPI 148 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_A>;
+ resets = <&arb AXG_ARB_TODDR_A>,
+ <&clkc_audio AUD_RESET_TODDR_A>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <512>;
+ status = "disabled";
+ };
+
+ toddr_b: audio-controller@140 {
+ compatible = "amlogic,g12a-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x140 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_B";
+ interrupts = <GIC_SPI 149 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_B>;
+ resets = <&arb AXG_ARB_TODDR_B>,
+ <&clkc_audio AUD_RESET_TODDR_B>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+
+ toddr_c: audio-controller@180 {
+ compatible = "amlogic,g12a-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x180 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_C";
+ interrupts = <GIC_SPI 150 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_C>;
+ resets = <&arb AXG_ARB_TODDR_C>,
+ <&clkc_audio AUD_RESET_TODDR_C>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+
+ frddr_a: audio-controller@1c0 {
+ compatible = "amlogic,g12a-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x1c0 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_A";
+ interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_A>;
+ resets = <&arb AXG_ARB_FRDDR_A>,
+ <&clkc_audio AUD_RESET_FRDDR_A>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <512>;
+ status = "disabled";
+ };
+
+ frddr_b: audio-controller@200 {
+ compatible = "amlogic,g12a-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x200 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_B";
+ interrupts = <GIC_SPI 153 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_B>;
+ resets = <&arb AXG_ARB_FRDDR_B>,
+ <&clkc_audio AUD_RESET_FRDDR_B>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+
+ frddr_c: audio-controller@240 {
+ compatible = "amlogic,g12a-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x240 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_C";
+ interrupts = <GIC_SPI 154 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_C>;
+ resets = <&arb AXG_ARB_FRDDR_C>,
+ <&clkc_audio AUD_RESET_FRDDR_C>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+
+ arb: reset-controller@280 {
+ status = "disabled";
+ compatible = "amlogic,meson-axg-audio-arb";
+ reg = <0x0 0x280 0x0 0x4>;
+ #reset-cells = <1>;
+ clocks = <&clkc_audio AUD_CLKID_DDR_ARB>;
+ };
+
+ tdmin_a: audio-controller@300 {
+ compatible = "amlogic,g12a-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x300 0x0 0x40>;
+ sound-name-prefix = "TDMIN_A";
+ resets = <&clkc_audio AUD_RESET_TDMIN_A>;
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_A>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmin_b: audio-controller@340 {
+ compatible = "amlogic,g12a-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x340 0x0 0x40>;
+ sound-name-prefix = "TDMIN_B";
+ resets = <&clkc_audio AUD_RESET_TDMIN_B>;
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_B>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmin_c: audio-controller@380 {
+ compatible = "amlogic,g12a-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x380 0x0 0x40>;
+ sound-name-prefix = "TDMIN_C";
+ resets = <&clkc_audio AUD_RESET_TDMIN_C>;
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_C>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmin_lb: audio-controller@3c0 {
+ compatible = "amlogic,g12a-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x3c0 0x0 0x40>;
+ sound-name-prefix = "TDMIN_LB";
+ resets = <&clkc_audio AUD_RESET_TDMIN_LB>;
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_LB>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ spdifin: audio-controller@400 {
+ compatible = "amlogic,g12a-spdifin",
+ "amlogic,axg-spdifin";
+ reg = <0x0 0x400 0x0 0x30>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFIN";
+ interrupts = <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_SPDIFIN>,
+ <&clkc_audio AUD_CLKID_SPDIFIN_CLK>;
+ clock-names = "pclk", "refclk";
+ resets = <&clkc_audio AUD_RESET_SPDIFIN>;
+ status = "disabled";
+ };
+
+ spdifout: audio-controller@480 {
+ compatible = "amlogic,g12a-spdifout",
+ "amlogic,axg-spdifout";
+ reg = <0x0 0x480 0x0 0x50>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFOUT";
+ clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>,
+ <&clkc_audio AUD_CLKID_SPDIFOUT_CLK>;
+ clock-names = "pclk", "mclk";
+ resets = <&clkc_audio AUD_RESET_SPDIFOUT>;
+ status = "disabled";
+ };
+
+ tdmout_a: audio-controller@500 {
+ compatible = "amlogic,g12a-tdmout";
+ reg = <0x0 0x500 0x0 0x40>;
+ sound-name-prefix = "TDMOUT_A";
+ resets = <&clkc_audio AUD_RESET_TDMOUT_A>;
+ clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmout_b: audio-controller@540 {
+ compatible = "amlogic,g12a-tdmout";
+ reg = <0x0 0x540 0x0 0x40>;
+ sound-name-prefix = "TDMOUT_B";
+ resets = <&clkc_audio AUD_RESET_TDMOUT_B>;
+ clocks = <&clkc_audio AUD_CLKID_TDMOUT_B>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmout_c: audio-controller@580 {
+ compatible = "amlogic,g12a-tdmout";
+ reg = <0x0 0x580 0x0 0x40>;
+ sound-name-prefix = "TDMOUT_C";
+ resets = <&clkc_audio AUD_RESET_TDMOUT_C>;
+ clocks = <&clkc_audio AUD_CLKID_TDMOUT_C>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ spdifout_b: audio-controller@680 {
+ compatible = "amlogic,g12a-spdifout",
+ "amlogic,axg-spdifout";
+ reg = <0x0 0x680 0x0 0x50>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SPDIFOUT_B";
+ clocks = <&clkc_audio AUD_CLKID_SPDIFOUT_B>,
+ <&clkc_audio AUD_CLKID_SPDIFOUT_B_CLK>;
+ clock-names = "pclk", "mclk";
+ resets = <&clkc_audio AUD_RESET_SPDIFOUT_B>;
+ status = "disabled";
+ };
+
+ tohdmitx: audio-controller@744 {
+ compatible = "amlogic,g12a-tohdmitx";
+ reg = <0x0 0x744 0x0 0x4>;
+ #sound-dai-cells = <1>;
+ sound-name-prefix = "TOHDMITX";
+ resets = <&clkc_audio AUD_RESET_TOHDMITX>;
+ status = "disabled";
+ };
+ };
+};
+
+&cpu_thermal {
+ cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+ðmac {
+ power-domains = <&pwrc PWRC_G12A_ETH_ID>;
+};
+
+&vpu {
+ power-domains = <&pwrc PWRC_G12A_VPU_ID>;
+};
+
+&sd_emmc_a {
+ amlogic,dram-access-quirk;
+};
+
+&simplefb_cvbs {
+ power-domains = <&pwrc PWRC_G12A_VPU_ID>;
+};
+
+&simplefb_hdmi {
+ power-domains = <&pwrc PWRC_G12A_VPU_ID>;
+};
+
@@ -129,6 +129,25 @@
enable-active-high;
};
+ vddcpu: regulator-vddcpu {
+ /*
+ * SY8120B1ABC DC/DC Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&dc_in>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vddio_ao1v8: regulator-vddio_ao1v8 {
compatible = "regulator-fixed";
regulator-name = "VDDIO_AO1V8";
@@ -297,6 +316,34 @@
status = "okay";
};
+&cpu0 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu2 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu3 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
&cvbs_vdac_port {
cvbs_vdac_out: endpoint {
remote-endpoint = <&cvbs_connector_in>;
@@ -339,6 +386,20 @@
pinctrl-names = "default";
};
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
@@ -377,6 +438,9 @@
non-removable;
disable-wp;
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
@@ -129,6 +129,24 @@
regulator-always-on;
};
+ vddcpu: regulator-vddcpu {
+ /*
+ * MP8756GD Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ vin-supply = <&main_12v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
};
&cec_AO {
@@ -145,6 +163,34 @@
hdmi-phandle = <&hdmi_tx>;
};
+&cpu0 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu2 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu3 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
&cvbs_vdac_port {
cvbs_vdac_out: endpoint {
remote-endpoint = <&cvbs_connector_in>;
@@ -197,6 +243,14 @@
pinctrl-names = "default";
};
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
/* SD card */
&sd_emmc_b {
status = "okay";
@@ -3,8 +3,7 @@
* Copyright (c) 2018 Amlogic, Inc. All rights reserved.
*/
-#include "meson-g12-common.dtsi"
-#include <dt-bindings/power/meson-g12a-power.h>
+#include "meson-g12.dtsi"
/ {
compatible = "amlogic,g12a";
@@ -19,6 +18,7 @@
reg = <0x0 0x0>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu1: cpu@1 {
@@ -27,6 +27,7 @@
reg = <0x0 0x1>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu2: cpu@2 {
@@ -35,6 +36,7 @@
reg = <0x0 0x2>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu3: cpu@3 {
@@ -43,6 +45,7 @@
reg = <0x0 0x3>;
enable-method = "psci";
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
l2: l2-cache0 {
@@ -111,14 +114,22 @@
};
};
-ðmac {
- power-domains = <&pwrc PWRC_G12A_ETH_ID>;
-};
-
-&vpu {
- power-domains = <&pwrc PWRC_G12A_VPU_ID>;
-};
+&cpu_thermal {
+ cooling-maps {
+ map0 {
+ trip = <&cpu_passive>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
-&sd_emmc_a {
- amlogic,dram-access-quirk;
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
};
@@ -14,3 +14,28 @@
/ {
compatible = "khadas,vim3", "amlogic,a311d", "amlogic,g12b";
};
+
+/*
+ * The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+ status = "okay";
+};
+
+&usb {
+ phys = <&usb2_phy0>, <&usb2_phy1>;
+ phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */
@@ -12,7 +12,7 @@
#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
/ {
- compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+ compatible = "hardkernel,odroid-n2", "amlogic,s922x", "amlogic,g12b";
model = "Hardkernel ODROID-N2";
aliases {
@@ -4,8 +4,7 @@
* Author: Neil Armstrong <narmstrong@baylibre.com>
*/
-#include "meson-g12-common.dtsi"
-#include <dt-bindings/power/meson-g12a-power.h>
+#include "meson-g12.dtsi"
/ {
compatible = "amlogic,g12b";
@@ -49,7 +48,9 @@
compatible = "arm,cortex-a53";
reg = <0x0 0x0>;
enable-method = "psci";
+ capacity-dmips-mhz = <592>;
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu1: cpu@1 {
@@ -57,7 +58,9 @@
compatible = "arm,cortex-a53";
reg = <0x0 0x1>;
enable-method = "psci";
+ capacity-dmips-mhz = <592>;
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu100: cpu@100 {
@@ -65,7 +68,9 @@
compatible = "arm,cortex-a73";
reg = <0x0 0x100>;
enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu101: cpu@101 {
@@ -73,7 +78,9 @@
compatible = "arm,cortex-a73";
reg = <0x0 0x101>;
enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu102: cpu@102 {
@@ -81,7 +88,9 @@
compatible = "arm,cortex-a73";
reg = <0x0 0x102>;
enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
cpu103: cpu@103 {
@@ -89,7 +98,9 @@
compatible = "arm,cortex-a73";
reg = <0x0 0x103>;
enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
next-level-cache = <&l2>;
+ #cooling-cells = <2>;
};
l2: l2-cache0 {
@@ -102,14 +113,3 @@
compatible = "amlogic,g12b-clkc";
};
-ðmac {
- power-domains = <&pwrc PWRC_G12A_ETH_ID>;
-};
-
-&vpu {
- power-domains = <&pwrc PWRC_G12A_VPU_ID>;
-};
-
-&sd_emmc_a {
- amlogic,dram-access-quirk;
-};
@@ -50,13 +50,35 @@
};
};
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ simplefb_cvbs: framebuffer-cvbs {
+ compatible = "amlogic,simple-framebuffer",
+ "simple-framebuffer";
+ amlogic,pipeline = "vpu-cvbs";
+ power-domains = <&pwrc_vpu>;
+ status = "disabled";
+ };
+
+ simplefb_hdmi: framebuffer-hdmi {
+ compatible = "amlogic,simple-framebuffer",
+ "simple-framebuffer";
+ amlogic,pipeline = "vpu-hdmi";
+ power-domains = <&pwrc_vpu>;
+ status = "disabled";
+ };
+ };
+
cpus {
#address-cells = <0x2>;
#size-cells = <0x0>;
cpu0: cpu@0 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x0>;
enable-method = "psci";
next-level-cache = <&l2>;
@@ -65,7 +87,7 @@
cpu1: cpu@1 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x1>;
enable-method = "psci";
next-level-cache = <&l2>;
@@ -74,7 +96,7 @@
cpu2: cpu@2 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x2>;
enable-method = "psci";
next-level-cache = <&l2>;
@@ -83,7 +105,7 @@
cpu3: cpu@3 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x3>;
enable-method = "psci";
next-level-cache = <&l2>;
@@ -139,6 +161,7 @@
#address-cells = <1>;
#size-cells = <1>;
read-only;
+ secure-monitor = <&sm>;
sn: sn@14 {
reg = <0x14 0x10>;
@@ -198,7 +221,7 @@
};
reset: reset-controller@4404 {
- compatible = "amlogic,meson-gx-reset", "amlogic,meson-gxbb-reset";
+ compatible = "amlogic,meson-gxbb-reset";
reg = <0x0 0x04404 0x0 0x9c>;
#reset-cells = <1>;
};
@@ -218,7 +241,7 @@
};
i2c_A: i2c@8500 {
- compatible = "amlogic,meson-gx-i2c", "amlogic,meson-gxbb-i2c";
+ compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x08500 0x0 0x20>;
interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
@@ -262,8 +285,13 @@
status = "disabled";
};
+ clock-measure@8758 {
+ compatible = "amlogic,meson-gx-clk-measure";
+ reg = <0x0 0x8758 0x0 0x10>;
+ };
+
i2c_B: i2c@87c0 {
- compatible = "amlogic,meson-gx-i2c", "amlogic,meson-gxbb-i2c";
+ compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x087c0 0x0 0x20>;
interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
@@ -272,7 +300,7 @@
};
i2c_C: i2c@87e0 {
- compatible = "amlogic,meson-gx-i2c", "amlogic,meson-gxbb-i2c";
+ compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x087e0 0x0 0x20>;
interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
@@ -290,7 +318,7 @@
};
spifc: spi@8c80 {
- compatible = "amlogic,meson-gx-spifc", "amlogic,meson-gxbb-spifc";
+ compatible = "amlogic,meson-gxbb-spifc";
reg = <0x0 0x08c80 0x0 0x80>;
#address-cells = <1>;
#size-cells = <0>;
@@ -298,7 +326,7 @@
};
watchdog@98d0 {
- compatible = "amlogic,meson-gx-wdt", "amlogic,meson-gxbb-wdt";
+ compatible = "amlogic,meson-gxbb-wdt";
reg = <0x0 0x098d0 0x0 0x10>;
clocks = <&xtal>;
};
@@ -364,6 +392,7 @@
compatible = "amlogic,meson-gx-ao-cec";
reg = <0x0 0x00100 0x0 0x14>;
interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
};
sec_AO: ao-secure@140 {
@@ -387,7 +416,7 @@
};
i2c_AO: i2c@500 {
- compatible = "amlogic,meson-gx-i2c", "amlogic,meson-gxbb-i2c";
+ compatible = "amlogic,meson-gxbb-i2c";
reg = <0x0 0x500 0x0 0x20>;
interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
@@ -410,7 +439,21 @@
};
};
- periphs: periphs@c8834000 {
+ vdec: video-codec@c8820000 {
+ compatible = "amlogic,gx-vdec";
+ reg = <0x0 0xc8820000 0x0 0x10000>,
+ <0x0 0xc110a580 0x0 0xe4>;
+ reg-names = "dos", "esparser";
+
+ interrupts = <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "vdec", "esparser";
+
+ amlogic,ao-sysctrl = <&sysctrl_AO>;
+ amlogic,canvas = <&canvas>;
+ };
+
+ periphs: bus@c8834000 {
compatible = "simple-bus";
reg = <0x0 0xc8834000 0x0 0x2000>;
#address-cells = <2>;
@@ -449,7 +492,7 @@
};
mailbox: mailbox@404 {
- compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
+ compatible = "amlogic,meson-gxbb-mhu";
reg = <0 0x404 0 0x4c>;
interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 209 IRQ_TYPE_EDGE_RISING>,
@@ -459,11 +502,15 @@
};
ethmac: ethernet@c9410000 {
- compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
- reg = <0x0 0xc9410000 0x0 0x10000
- 0x0 0xc8834540 0x0 0x4>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
+ compatible = "amlogic,meson-gxbb-dwmac",
+ "snps,dwmac-3.70a",
+ "snps,dwmac";
+ reg = <0x0 0xc9410000 0x0 0x10000>,
+ <0x0 0xc8834540 0x0 0x4>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
+ rx-fifo-depth = <4096>;
+ tx-fifo-depth = <2048>;
status = "disabled";
};
@@ -499,12 +546,12 @@
vpu: vpu@d0100000 {
compatible = "amlogic,meson-gx-vpu";
reg = <0x0 0xd0100000 0x0 0x100000>,
- <0x0 0xc883c000 0x0 0x1000>,
- <0x0 0xc8838000 0x0 0x1000>;
- reg-names = "vpu", "hhi", "dmc";
+ <0x0 0xc883c000 0x0 0x1000>;
+ reg-names = "vpu", "hhi";
interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
#size-cells = <0>;
+ amlogic,canvas = <&canvas>;
/* CVBS VDAC output port */
cvbs_vdac_port: port@0 {
@@ -10,6 +10,7 @@
/ {
compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
+ model = "FriendlyARM NanoPi K2";
aliases {
serial0 = &uart_AO;
@@ -154,10 +155,6 @@
amlogic,tx-delay-ns = <2>;
- snps,reset-gpio = <&gpio GPIOZ_14 0>;
- snps,reset-delays-us = <0 10000 1000000>;
- snps,reset-active-low;
-
mdio {
compatible = "snps,dwmac-mdio";
#address-cells = <1>;
@@ -166,6 +163,11 @@
eth_phy0: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_15 */
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
@@ -191,7 +193,7 @@
pinctrl-names = "default";
};
-&pinctrl_aobus {
+&gpio_ao {
gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
"VCCK En", "CON1 Header Pin31",
"I2S Header Pin6", "IR In", "I2S Header Pin7",
@@ -201,7 +203,7 @@
"";
};
-&pinctrl_periphs {
+&gpio {
gpio-line-names = /* Bank GPIOZ */
"Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
"Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
@@ -273,11 +275,14 @@
bus-width = <4>;
cap-sd-highspeed;
- max-frequency = <200000000>;
+ max-frequency = <50000000>;
non-removable;
disable-wp;
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddio_ao3v3>;
@@ -301,12 +306,11 @@
sd-uhs-sdr12;
sd-uhs-sdr25;
sd-uhs-sdr50;
- sd-uhs-sdr104;
- max-frequency = <200000000>;
+ sd-uhs-ddr50;
+ max-frequency = <100000000>;
disable-wp;
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vddio_ao3v3>;
vqmmc-supply = <&vddio_tf>;
@@ -36,8 +36,15 @@
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
+ /*
+ * signal name from schematics: PWREN
+ */
gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
enable-active-high;
+ /*
+ * signal name from schematics: USB_POWER
+ */
+ vin-supply = <&p5v0>;
};
leds {
@@ -50,18 +57,38 @@
};
};
+ p5v0: regulator-p5v0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "P5V0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ hdmi_p5v0: regulator-hdmi_p5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "HDMI_P5V0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ /* AP2331SA-7 */
+ vin-supply = <&p5v0>;
+ };
+
tflash_vdd: regulator-tflash_vdd {
- /*
- * signal name from schematics: TFLASH_VDD_EN
- */
compatible = "regulator-fixed";
regulator-name = "TFLASH_VDD";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ /*
+ * signal name from schematics: TFLASH_VDD_EN
+ */
gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>;
enable-active-high;
+ /* U16 RT9179GB */
+ vin-supply = <&vddio_ao3v3>;
};
tf_io: gpio-regulator-tf_io {
@@ -77,8 +104,10 @@
gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
gpios-states = <0>;
- states = <3300000 0
- 1800000 1>;
+ states = <3300000 0>,
+ <1800000 1>;
+ /* U12/U13 RT9179GB */
+ vin-supply = <&vddio_ao3v3>;
};
vcc1v8: regulator-vcc1v8 {
@@ -86,6 +115,9 @@
regulator-name = "VCC1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ /* U18 RT9179GB */
+ vin-supply = <&vddio_ao3v3>;
};
vcc3v3: regulator-vcc3v3 {
@@ -95,6 +127,36 @@
regulator-max-microvolt = <3300000>;
};
+ vddio_ao1v8: regulator-vddio-ao1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ /* U17 RT9179GB */
+ vin-supply = <&p5v0>;
+ };
+
+ vddio_ao3v3: regulator-vddio-ao3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ /* U11 MP2161GJ-C499 */
+ vin-supply = <&p5v0>;
+ };
+
+ ddr3_1v5: regulator-ddr3_1v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "DDR3_1V5";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ /* U15 MP2161GJ-C499 */
+ vin-supply = <&p5v0>;
+ };
+
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
@@ -126,10 +188,6 @@
phy-handle = <ð_phy0>;
phy-mode = "rgmii";
- snps,reset-gpio = <&gpio GPIOZ_14 0>;
- snps,reset-delays-us = <0 10000 1000000>;
- snps,reset-active-low;
-
amlogic,tx-delay-ns = <2>;
mdio {
@@ -140,10 +198,14 @@
eth_phy0: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_15 */
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
- eee-broken-1000t;
};
};
};
@@ -167,6 +229,7 @@
status = "okay";
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
pinctrl-names = "default";
+ hdmi-supply = <&hdmi_p5v0>;
};
&hdmi_tx_tmds_port {
@@ -187,7 +250,7 @@
pinctrl-names = "default";
};
-&pinctrl_aobus {
+&gpio_ao {
gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
"USB HUB nRESET", "USB OTG Power En",
"J7 Header Pin2", "IR In", "J7 Header Pin4",
@@ -197,7 +260,7 @@
"";
};
-&pinctrl_periphs {
+&gpio {
gpio-line-names = /* Bank GPIOZ */
"Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
"Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
@@ -256,11 +319,14 @@
bus-width = <4>;
cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-ddr50;
max-frequency = <100000000>;
disable-wp;
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&tflash_vdd>;
vqmmc-supply = <&tf_io>;
@@ -274,7 +340,7 @@
pinctrl-names = "default", "clk-gate";
bus-width = <8>;
- max-frequency = <100000000>;
+ max-frequency = <200000000>;
non-removable;
disable-wp;
cap-mmc-highspeed;
@@ -293,7 +359,7 @@
};
&usb0_phy {
- status = "okay";
+ status = "disabled";
phy-supply = <&usb_otg_pwr>;
};
@@ -303,7 +369,7 @@
};
&usb0 {
- status = "okay";
+ status = "disabled";
};
&usb1 {
@@ -68,10 +68,6 @@
amlogic,tx-delay-ns = <2>;
- snps,reset-gpio = <&gpio GPIOZ_14 0>;
- snps,reset-delays-us = <0 10000 1000000>;
- snps,reset-active-low;
-
mdio {
compatible = "snps,dwmac-mdio";
#address-cells = <1>;
@@ -80,6 +76,11 @@
eth_phy0: ethernet-phy@3 {
/* Micrel KSZ9031 (0x00221620) */
reg = <3>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_15 */
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
@@ -21,6 +21,6 @@
phy-mode = "rmii";
snps,reset-gpio = <&gpio GPIOZ_14 0>;
- snps,reset-delays-us = <0 10000 1000000>;
+ snps,reset-delays-us = <0>, <10000>, <1000000>;
snps,reset-active-low;
};
@@ -46,8 +46,8 @@
gpios-states = <1>;
/* Based on P200 schematics, signal CARD_1.8V/3.3V_CTR */
- states = <1800000 0
- 3300000 1>;
+ states = <1800000 0>,
+ <3300000 1>;
regulator-settling-time-up-us = <10000>;
regulator-settling-time-down-us = <150000>;
@@ -165,11 +165,14 @@
bus-width = <4>;
cap-sd-highspeed;
- max-frequency = <100000000>;
+ max-frequency = <50000000>;
non-removable;
disable-wp;
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
@@ -81,6 +81,7 @@
mux {
groups = "uart_tx_ao_a", "uart_rx_ao_a";
function = "uart_ao";
+ bias-disable;
};
};
@@ -89,6 +90,7 @@
groups = "uart_cts_ao_a",
"uart_rts_ao_a";
function = "uart_ao";
+ bias-disable;
};
};
@@ -96,6 +98,7 @@
mux {
groups = "uart_tx_ao_b", "uart_rx_ao_b";
function = "uart_ao_b";
+ bias-disable;
};
};
@@ -104,6 +107,7 @@
groups = "uart_cts_ao_b",
"uart_rts_ao_b";
function = "uart_ao_b";
+ bias-disable;
};
};
@@ -111,6 +115,7 @@
mux {
groups = "remote_input_ao";
function = "remote_input_ao";
+ bias-disable;
};
};
@@ -119,6 +124,7 @@
groups = "i2c_sck_ao",
"i2c_sda_ao";
function = "i2c_ao";
+ bias-disable;
};
};
@@ -126,6 +132,7 @@
mux {
groups = "pwm_ao_a_3";
function = "pwm_ao_a_3";
+ bias-disable;
};
};
@@ -133,6 +140,7 @@
mux {
groups = "pwm_ao_a_6";
function = "pwm_ao_a_6";
+ bias-disable;
};
};
@@ -140,6 +148,7 @@
mux {
groups = "pwm_ao_a_12";
function = "pwm_ao_a_12";
+ bias-disable;
};
};
@@ -147,6 +156,7 @@
mux {
groups = "pwm_ao_b";
function = "pwm_ao_b";
+ bias-disable;
};
};
@@ -154,6 +164,7 @@
mux {
groups = "i2s_am_clk";
function = "i2s_out_ao";
+ bias-disable;
};
};
@@ -161,6 +172,7 @@
mux {
groups = "i2s_out_ao_clk";
function = "i2s_out_ao";
+ bias-disable;
};
};
@@ -168,6 +180,7 @@
mux {
groups = "i2s_out_lr_clk";
function = "i2s_out_ao";
+ bias-disable;
};
};
@@ -175,6 +188,7 @@
mux {
groups = "i2s_out_ch01_ao";
function = "i2s_out_ao";
+ bias-disable;
};
};
@@ -182,6 +196,7 @@
mux {
groups = "i2s_out_ch23_ao";
function = "i2s_out_ao";
+ bias-disable;
};
};
@@ -189,6 +204,7 @@
mux {
groups = "i2s_out_ch45_ao";
function = "i2s_out_ao";
+ bias-disable;
};
};
@@ -203,6 +219,7 @@
mux {
groups = "spdif_out_ao_13";
function = "spdif_out_ao";
+ bias-disable;
};
};
@@ -210,6 +227,7 @@
mux {
groups = "ao_cec";
function = "cec_ao";
+ bias-disable;
};
};
@@ -217,6 +235,7 @@
mux {
groups = "ee_cec";
function = "cec_ao";
+ bias-disable;
};
};
};
@@ -280,6 +299,12 @@
&clkc_AO {
compatible = "amlogic,meson-gxbb-aoclkc", "amlogic,meson-gx-aoclkc";
+ clocks = <&xtal>, <&clkc CLKID_CLK81>;
+ clock-names = "xtal", "mpeg-clk";
+};
+
+&efuse {
+ clocks = <&clkc CLKID_EFUSE>;
};
ðmac {
@@ -311,6 +336,8 @@
clkc: clock-controller {
compatible = "amlogic,gxbb-clkc";
#clock-cells = <1>;
+ clocks = <&xtal>;
+ clock-names = "xtal";
};
};
@@ -354,11 +381,17 @@
};
emmc_pins: emmc {
- mux {
+ mux-0 {
groups = "emmc_nand_d07",
- "emmc_cmd",
- "emmc_clk";
+ "emmc_cmd";
function = "emmc";
+ bias-pull-up;
+ };
+
+ mux-1 {
+ groups = "emmc_clk";
+ function = "emmc";
+ bias-disable;
};
};
@@ -366,6 +399,7 @@
mux {
groups = "emmc_ds";
function = "emmc";
+ bias-pull-down;
};
};
@@ -373,9 +407,6 @@
mux {
groups = "BOOT_8";
function = "gpio_periphs";
- };
- cfg-pull-down {
- pins = "BOOT_8";
bias-pull-down;
};
};
@@ -387,6 +418,7 @@
"nor_c",
"nor_cs";
function = "nor";
+ bias-disable;
};
};
@@ -396,6 +428,7 @@
"spi_mosi",
"spi_sclk";
function = "spi";
+ bias-disable;
};
};
@@ -403,18 +436,25 @@
mux {
groups = "spi_ss0";
function = "spi";
+ bias-disable;
};
};
sdcard_pins: sdcard {
- mux {
+ mux-0 {
groups = "sdcard_d0",
"sdcard_d1",
"sdcard_d2",
"sdcard_d3",
- "sdcard_cmd",
- "sdcard_clk";
+ "sdcard_cmd";
+ function = "sdcard";
+ bias-pull-up;
+ };
+
+ mux-1 {
+ groups = "sdcard_clk";
function = "sdcard";
+ bias-disable;
};
};
@@ -422,22 +462,25 @@
mux {
groups = "CARD_2";
function = "gpio_periphs";
- };
- cfg-pull-down {
- pins = "CARD_2";
bias-pull-down;
};
};
sdio_pins: sdio {
- mux {
+ mux-0 {
groups = "sdio_d0",
"sdio_d1",
"sdio_d2",
"sdio_d3",
- "sdio_cmd",
- "sdio_clk";
+ "sdio_cmd";
+ function = "sdio";
+ bias-pull-up;
+ };
+
+ mux-1 {
+ groups = "sdio_clk";
function = "sdio";
+ bias-disable;
};
};
@@ -445,9 +488,6 @@
mux {
groups = "GPIOX_4";
function = "gpio_periphs";
- };
- cfg-pull-down {
- pins = "GPIOX_4";
bias-pull-down;
};
};
@@ -456,6 +496,7 @@
mux {
groups = "sdio_irq";
function = "sdio";
+ bias-disable;
};
};
@@ -464,6 +505,7 @@
groups = "uart_tx_a",
"uart_rx_a";
function = "uart_a";
+ bias-disable;
};
};
@@ -472,6 +514,7 @@
groups = "uart_cts_a",
"uart_rts_a";
function = "uart_a";
+ bias-disable;
};
};
@@ -480,6 +523,7 @@
groups = "uart_tx_b",
"uart_rx_b";
function = "uart_b";
+ bias-disable;
};
};
@@ -488,6 +532,7 @@
groups = "uart_cts_b",
"uart_rts_b";
function = "uart_b";
+ bias-disable;
};
};
@@ -496,6 +541,7 @@
groups = "uart_tx_c",
"uart_rx_c";
function = "uart_c";
+ bias-disable;
};
};
@@ -504,6 +550,7 @@
groups = "uart_cts_c",
"uart_rts_c";
function = "uart_c";
+ bias-disable;
};
};
@@ -512,6 +559,7 @@
groups = "i2c_sck_a",
"i2c_sda_a";
function = "i2c_a";
+ bias-disable;
};
};
@@ -520,6 +568,7 @@
groups = "i2c_sck_b",
"i2c_sda_b";
function = "i2c_b";
+ bias-disable;
};
};
@@ -528,6 +577,7 @@
groups = "i2c_sck_c",
"i2c_sda_c";
function = "i2c_c";
+ bias-disable;
};
};
@@ -548,6 +598,7 @@
"eth_txd2",
"eth_txd3";
function = "eth";
+ bias-disable;
};
};
@@ -563,6 +614,7 @@
"eth_txd0",
"eth_txd1";
function = "eth";
+ bias-disable;
};
};
@@ -570,6 +622,7 @@
mux {
groups = "pwm_a_x";
function = "pwm_a_x";
+ bias-disable;
};
};
@@ -577,6 +630,7 @@
mux {
groups = "pwm_a_y";
function = "pwm_a_y";
+ bias-disable;
};
};
@@ -584,6 +638,7 @@
mux {
groups = "pwm_b";
function = "pwm_b";
+ bias-disable;
};
};
@@ -591,6 +646,7 @@
mux {
groups = "pwm_d";
function = "pwm_d";
+ bias-disable;
};
};
@@ -598,6 +654,7 @@
mux {
groups = "pwm_e";
function = "pwm_e";
+ bias-disable;
};
};
@@ -605,6 +662,7 @@
mux {
groups = "pwm_f_x";
function = "pwm_f_x";
+ bias-disable;
};
};
@@ -612,6 +670,7 @@
mux {
groups = "pwm_f_y";
function = "pwm_f_y";
+ bias-disable;
};
};
@@ -619,6 +678,7 @@
mux {
groups = "hdmi_hpd";
function = "hdmi_hpd";
+ bias-disable;
};
};
@@ -626,6 +686,7 @@
mux {
groups = "hdmi_sda", "hdmi_scl";
function = "hdmi_i2c";
+ bias-disable;
};
};
@@ -633,6 +694,7 @@
mux {
groups = "i2sout_ch23_y";
function = "i2s_out";
+ bias-disable;
};
};
@@ -640,6 +702,7 @@
mux {
groups = "i2sout_ch45_y";
function = "i2s_out";
+ bias-disable;
};
};
@@ -647,6 +710,7 @@
mux {
groups = "i2sout_ch67_y";
function = "i2s_out";
+ bias-disable;
};
};
@@ -654,6 +718,7 @@
mux {
groups = "spdif_out_y";
function = "spdif_out";
+ bias-disable;
};
};
};
@@ -734,6 +799,12 @@
resets = <&reset RESET_SD_EMMC_C>;
};
+&simplefb_hdmi {
+ clocks = <&clkc CLKID_HDMI_PCLK>,
+ <&clkc CLKID_CLK81>,
+ <&clkc CLKID_GCLK_VENCI_INT0>;
+};
+
&spicc {
clocks = <&clkc CLKID_SPICC>;
clock-names = "core";
@@ -774,3 +845,14 @@
compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
power-domains = <&pwrc_vpu>;
};
+
+&vdec {
+ compatible = "amlogic,gxbb-vdec", "amlogic,gx-vdec";
+ clocks = <&clkc CLKID_DOS_PARSER>,
+ <&clkc CLKID_DOS>,
+ <&clkc CLKID_VDEC_1>,
+ <&clkc CLKID_VDEC_HEVC>;
+ clock-names = "dos_parser", "dos", "vdec_1", "vdec_hevc";
+ resets = <&reset RESET_PARSER>;
+ reset-names = "esparser";
+};
@@ -14,7 +14,7 @@
/ {
compatible = "libretech,aml-s805x-ac", "amlogic,s805x",
"amlogic,meson-gxl";
- model = "Libre Computer Board AML-S805X-AC";
+ model = "Libre Computer AML-S805X-AC";
aliases {
serial0 = &uart_AO;
@@ -33,11 +33,9 @@
gpio-keys-polled {
compatible = "gpio-keys-polled";
- #address-cells = <1>;
- #size-cells = <0>;
poll-interval = <100>;
- button@0 {
+ power-button {
label = "power";
linux,code = <KEY_POWER>;
gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
@@ -110,10 +108,10 @@
};
&ir {
- linux,rc-map-name = "rc-geekbox";
+ linux,rc-map-name = "rc-khadas";
};
-&pinctrl_aobus {
+&gpio_ao {
gpio-line-names = "UART TX",
"UART RX",
"Power Key In",
@@ -128,7 +126,7 @@
"";
};
-&pinctrl_periphs {
+&gpio {
gpio-line-names = /* Bank GPIOZ */
"", "", "", "", "", "", "",
"", "", "", "", "", "", "",
@@ -188,6 +186,16 @@
};
};
+&uart_A {
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ max-speed = <2000000>;
+ clocks = <&wifi32k>;
+ clock-names = "lpo";
+ };
+};
+
/* This is brought out on the Linux_RX (18) and Linux_TX (19) pins: */
&uart_AO {
status = "okay";
@@ -12,8 +12,9 @@
#include "meson-gxl-s905x.dtsi"
/ {
- compatible = "libretech,cc", "amlogic,s905x", "amlogic,meson-gxl";
- model = "Libre Computer Board AML-S905X-CC";
+ compatible = "libretech,aml-s905x-cc", "amlogic,s905x",
+ "amlogic,meson-gxl";
+ model = "Libre Computer AML-S905X-CC";
aliases {
serial0 = &uart_AO;
@@ -115,11 +116,13 @@
regulator-max-microvolt = <1800000>;
};
+ /* This is provided by LDOs on the eMMC daugther card */
vddio_boot: regulator-vddio_boot {
compatible = "regulator-fixed";
regulator-name = "VDDIO_BOOT";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
};
};
@@ -164,7 +167,7 @@
};
};
-&pinctrl_aobus {
+&gpio_ao {
gpio-line-names = "UART TX",
"UART RX",
"Blue LED",
@@ -179,7 +182,7 @@
"7J1 Header Pin15";
};
-&pinctrl_periphs {
+&gpio {
gpio-line-names = /* Bank GPIOZ */
"", "", "", "", "", "", "",
"", "", "", "", "", "", "",
@@ -235,11 +238,10 @@
bus-width = <4>;
cap-sd-highspeed;
- max-frequency = <100000000>;
+ max-frequency = <50000000>;
disable-wp;
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vcc_card>;
@@ -254,9 +256,9 @@
bus-width = <8>;
cap-mmc-highspeed;
- mmc-ddr-3_3v;
- max-frequency = <50000000>;
- non-removable;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
disable-wp;
mmc-pwrseq = <&emmc_pwrseq>;
@@ -114,11 +114,14 @@
bus-width = <4>;
cap-sd-highspeed;
- max-frequency = <100000000>;
+ max-frequency = <50000000>;
non-removable;
disable-wp;
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
@@ -134,11 +137,10 @@
bus-width = <4>;
cap-sd-highspeed;
- max-frequency = <100000000>;
+ max-frequency = <50000000>;
disable-wp;
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
@@ -36,6 +36,16 @@
phys = <&usb3_phy>, <&usb2_phy0>, <&usb2_phy1>;
};
};
+
+ crypto: crypto@c883e000 {
+ compatible = "amlogic,gxl-crypto";
+ reg = <0x0 0xc883e000 0x0 0x36>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 189 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_BLKMV>;
+ clock-names = "blkmv";
+ status = "okay";
+ };
};
};
@@ -80,9 +90,6 @@
};
ðmac {
- reg = <0x0 0xc9410000 0x0 0x10000
- 0x0 0xc8834540 0x0 0x4>;
-
clocks = <&clkc CLKID_ETH>,
<&clkc CLKID_FCLK_DIV2>,
<&clkc CLKID_MPLL2>;
@@ -326,10 +333,15 @@
};
emmc_pins: emmc {
- mux {
+ mux-0 {
groups = "emmc_nand_d07",
- "emmc_cmd",
- "emmc_clk";
+ "emmc_cmd";
+ function = "emmc";
+ bias-pull-up;
+ };
+
+ mux-1 {
+ groups = "emmc_clk";
function = "emmc";
bias-disable;
};
@@ -339,7 +351,7 @@
mux {
groups = "emmc_ds";
function = "emmc";
- bias-disable;
+ bias-pull-down;
};
};
@@ -381,13 +393,18 @@
};
sdcard_pins: sdcard {
- mux {
+ mux-0 {
groups = "sdcard_d0",
"sdcard_d1",
"sdcard_d2",
"sdcard_d3",
- "sdcard_cmd",
- "sdcard_clk";
+ "sdcard_cmd";
+ function = "sdcard";
+ bias-pull-up;
+ };
+
+ mux-1 {
+ groups = "sdcard_clk";
function = "sdcard";
bias-disable;
};
@@ -402,13 +419,18 @@
};
sdio_pins: sdio {
- mux {
+ mux-0 {
groups = "sdio_d0",
"sdio_d1",
"sdio_d2",
"sdio_d3",
- "sdio_cmd",
- "sdio_clk";
+ "sdio_cmd";
+ function = "sdio";
+ bias-pull-up;
+ };
+
+ mux-1 {
+ groups = "sdio_clk";
function = "sdio";
bias-disable;
};
@@ -511,6 +533,15 @@
};
};
+ i2c_c_dv18_pins: i2c_c_dv18 {
+ mux {
+ groups = "i2c_sck_c_dv19",
+ "i2c_sda_c_dv18";
+ function = "i2c_c";
+ bias-disable;
+ };
+ };
+
eth_pins: eth_c {
mux {
groups = "eth_mdio",
@@ -697,7 +728,7 @@
#size-cells = <0>;
internal_phy: ethernet-phy@8 {
- compatible = "ethernet-phy-id0181.4400", "ethernet-phy-ieee802.3-c22";
+ compatible = "ethernet-phy-id0181.4400";
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
reg = <8>;
max-speed = <100>;
@@ -787,6 +818,12 @@
resets = <&reset RESET_SD_EMMC_C>;
};
+&simplefb_hdmi {
+ clocks = <&clkc CLKID_HDMI_PCLK>,
+ <&clkc CLKID_CLK81>,
+ <&clkc CLKID_GCLK_VENCI_INT0>;
+};
+
&spicc {
clocks = <&clkc CLKID_SPICC>;
clock-names = "core";
@@ -827,3 +864,14 @@
compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
power-domains = <&pwrc_vpu>;
};
+
+&vdec {
+ compatible = "amlogic,gxl-vdec", "amlogic,gx-vdec";
+ clocks = <&clkc CLKID_DOS_PARSER>,
+ <&clkc CLKID_DOS>,
+ <&clkc CLKID_VDEC_1>,
+ <&clkc CLKID_VDEC_HEVC>;
+ clock-names = "dos_parser", "dos", "vdec_1", "vdec_hevc";
+ resets = <&reset RESET_PARSER>;
+ reset-names = "esparser";
+};
@@ -18,7 +18,6 @@
aliases {
serial0 = &uart_AO;
- serial1 = &uart_A;
serial2 = &uart_AO_B;
};
@@ -63,11 +62,9 @@
gpio-keys-polled {
compatible = "gpio-keys-polled";
- #address-cells = <1>;
- #size-cells = <0>;
poll-interval = <100>;
- button@0 {
+ power-button {
label = "power";
linux,code = <KEY_POWER>;
gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
@@ -132,19 +129,15 @@
map1 {
trip = <&cpu_alert1>;
- cooling-device = <&gpio_fan 2 THERMAL_NO_LIMIT>;
- };
-
- map2 {
- trip = <&cpu_alert1>;
- cooling-device =
- <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
-
- map3 {
- trip = <&cpu_alert1>;
- cooling-device =
- <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ cooling-device = <&gpio_fan 2 THERMAL_NO_LIMIT>,
+ <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
@@ -246,11 +239,6 @@
amlogic,tx-delay-ns = <2>;
- /* External PHY reset is shared with internal PHY Led signals */
- snps,reset-gpio = <&gpio GPIOZ_14 0>;
- snps,reset-delays-us = <0 10000 1000000>;
- snps,reset-active-low;
-
/* External PHY is in RGMII */
phy-mode = "rgmii";
@@ -261,6 +249,11 @@
external_phy: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_15 */
interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
@@ -306,7 +299,7 @@
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
- linux,rc-map-name = "rc-geekbox";
+ linux,rc-map-name = "rc-khadas";
};
&pwm_AO_ab {
@@ -328,16 +321,20 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
- max-frequency = <100000000>;
+ max-frequency = <50000000>;
non-removable;
disable-wp;
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
@@ -353,15 +350,15 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
- max-frequency = <100000000>;
+ max-frequency = <50000000>;
disable-wp;
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
@@ -371,17 +368,16 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
- cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
- mmc-hs400-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
@@ -409,8 +405,17 @@
/* This one is connected to the Bluetooth module */
&uart_A {
status = "okay";
- pinctrl-0 = <&uart_a_pins>;
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ max-speed = <2000000>;
+ clocks = <&wifi32k>;
+ clock-names = "lpo";
+ };
};
/* This is brought out on the Linux_RX (18) and Linux_TX (19) pins: */
@@ -44,7 +44,7 @@
cpu4: cpu@100 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x100>;
enable-method = "psci";
next-level-cache = <&l2>;
@@ -53,7 +53,7 @@
cpu5: cpu@101 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x101>;
enable-method = "psci";
next-level-cache = <&l2>;
@@ -62,7 +62,7 @@
cpu6: cpu@102 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x102>;
enable-method = "psci";
next-level-cache = <&l2>;
@@ -71,7 +71,7 @@
cpu7: cpu@103 {
device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
+ compatible = "arm,cortex-a53";
reg = <0x0 0x103>;
enable-method = "psci";
next-level-cache = <&l2>;
@@ -91,6 +91,33 @@
reset-names = "phy";
status = "okay";
};
+
+ mali: gpu@c0000 {
+ compatible = "amlogic,meson-gxm-mali", "arm,mali-t820";
+ reg = <0x0 0xc0000 0x0 0x40000>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "job", "mmu", "gpu";
+ clocks = <&clkc CLKID_MALI>;
+ resets = <&reset RESET_MALI_CAPB3>, <&reset RESET_MALI>;
+
+ /*
+ * Mali clocking is provided by two identical clock paths
+ * MALI_0 and MALI_1 muxed to a single clock by a glitch
+ * free mux to safely change frequency while running.
+ */
+ assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
+ <&clkc CLKID_MALI_0>,
+ <&clkc CLKID_MALI>; /* Glitch free mux */
+ assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_MALI_0>;
+ assigned-clock-rates = <0>, /* Do Nothing */
+ <666666666>,
+ <0>; /* Do Nothing */
+ };
};
&clkc_AO {
@@ -117,3 +144,7 @@
&dwc3 {
phys = <&usb3_phy>, <&usb2_phy0>, <&usb2_phy1>, <&usb2_phy2>;
};
+
+&vdec {
+ compatible = "amlogic,gxm-vdec", "amlogic,gx-vdec";
+};
@@ -246,6 +246,10 @@
linux,rc-map-name = "rc-khadas";
};
+&pcie {
+ reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>;
+};
+
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
@@ -274,6 +278,9 @@
non-removable;
disable-wp;
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vsys_3v3>;
new file mode 100644
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1.dtsi"
+#include "meson-khadas-vim3.dtsi"
+
+/ {
+ compatible = "khadas,vim3l", "amlogic,sm1";
+ model = "Khadas VIM3L";
+
+ vddcpu: regulator-vddcpu {
+ /*
+ * Silergy SY8030DEC Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <690000>;
+ regulator-max-microvolt = <1050000>;
+
+ vin-supply = <&vsys_3v3>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU1_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu2 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU2_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu3 {
+ cpu-supply = <&vddcpu>;
+ operating-points-v2 = <&cpu_opp_table>;
+ clocks = <&clkc CLKID_CPU3_CLK>;
+ clock-latency = <50000>;
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
+/*
+ * The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+ status = "okay";
+};
+
+&usb {
+ phys = <&usb2_phy0>, <&usb2_phy1>;
+ phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */
@@ -9,6 +9,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
/ {
compatible = "seirobotics,sei610", "amlogic,sm1";
@@ -19,6 +20,22 @@
ethernet0 = ðmac;
};
+ mono_dac: audio-codec-0 {
+ compatible = "maxim,max98357a";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "U16";
+ sdmode-gpios = <&gpio GPIOX_8 GPIO_ACTIVE_HIGH>;
+ };
+
+ dmics: audio-codec-1 {
+ #sound-dai-cells = <0>;
+ compatible = "dmic-codec";
+ num-channels = <2>;
+ wakeup-delay-ms = <50>;
+ status = "okay";
+ sound-name-prefix = "MIC";
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
@@ -29,25 +46,47 @@
};
gpio-keys {
- compatible = "gpio-keys-polled";
- poll-interval = <100>;
+ compatible = "gpio-keys";
key1 {
label = "A";
linux,code = <BTN_0>;
gpios = <&gpio GPIOH_6 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <34 IRQ_TYPE_EDGE_BOTH>;
};
key2 {
label = "B";
linux,code = <BTN_1>;
gpios = <&gpio GPIOH_7 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <35 IRQ_TYPE_EDGE_BOTH>;
};
key3 {
label = "C";
linux,code = <BTN_2>;
gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <2 IRQ_TYPE_EDGE_BOTH>;
+ };
+
+ mic_mute {
+ label = "MicMute";
+ linux,code = <SW_MUTE_DEVICE>;
+ linux,input-type = <EV_SW>;
+ gpios = <&gpio_ao GPIOE_2 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <99 IRQ_TYPE_EDGE_BOTH>;
+ };
+
+ power_key {
+ label = "PowerKey";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
};
};
@@ -179,6 +218,120 @@
clock-names = "ext_clock";
};
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "SM1-SEI610";
+ audio-aux-devs = <&tdmout_a>, <&tdmout_b>,
+ <&tdmin_a>, <&tdmin_b>;
+ audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0",
+ "TDMOUT_A IN 1", "FRDDR_B OUT 0",
+ "TDMOUT_A IN 2", "FRDDR_C OUT 0",
+ "TDM_A Playback", "TDMOUT_A OUT",
+ "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+ "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT",
+ "TODDR_A IN 4", "PDM Capture",
+ "TODDR_B IN 4", "PDM Capture",
+ "TODDR_C IN 4", "PDM Capture",
+ "TDMIN_A IN 0", "TDM_A Capture",
+ "TDMIN_A IN 3", "TDM_A Loopback",
+ "TDMIN_B IN 0", "TDM_A Capture",
+ "TDMIN_B IN 3", "TDM_A Loopback",
+ "TDMIN_A IN 1", "TDM_B Capture",
+ "TDMIN_A IN 4", "TDM_B Loopback",
+ "TDMIN_B IN 1", "TDM_B Capture",
+ "TDMIN_B IN 4", "TDM_B Loopback",
+ "TODDR_A IN 0", "TDMIN_A OUT",
+ "TODDR_B IN 0", "TDMIN_A OUT",
+ "TODDR_C IN 0", "TDMIN_A OUT",
+ "TODDR_A IN 1", "TDMIN_B OUT",
+ "TODDR_B IN 1", "TDMIN_B OUT",
+ "TODDR_C IN 1", "TDMIN_B OUT";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+ status = "okay";
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&frddr_b>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&frddr_c>;
+ };
+
+ dai-link-3 {
+ sound-dai = <&toddr_a>;
+ };
+
+ dai-link-4 {
+ sound-dai = <&toddr_b>;
+ };
+
+ dai-link-5 {
+ sound-dai = <&toddr_c>;
+ };
+
+ /* internal speaker interface */
+ dai-link-6 {
+ sound-dai = <&tdmif_a>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ mclk-fs = <256>;
+
+ codec-0 {
+ sound-dai = <&mono_dac>;
+ };
+
+ codec-1 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>;
+ };
+ };
+
+ /* 8ch hdmi interface */
+ dai-link-7 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ /* internal digital mics */
+ dai-link-8 {
+ sound-dai = <&pdm>;
+
+ codec {
+ sound-dai = <&dmics>;
+ };
+ };
+
+ /* hdmi glue */
+ dai-link-9 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+
wifi32k: wifi32k {
compatible = "pwm-clock";
#clock-cells = <0>;
@@ -187,6 +340,10 @@
};
};
+&arb {
+ status = "okay";
+};
+
&cec_AO {
pinctrl-0 = <&cec_ao_a_h_pins>;
pinctrl-names = "default";
@@ -201,6 +358,10 @@
hdmi-phandle = <&hdmi_tx>;
};
+&clkc_audio {
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <&vddcpu>;
operating-points-v2 = <&cpu_opp_table>;
@@ -235,6 +396,18 @@
phy-mode = "rmii";
};
+&frddr_a {
+ status = "okay";
+};
+
+&frddr_b {
+ status = "okay";
+};
+
+&frddr_c {
+ status = "okay";
+};
+
&hdmi_tx {
status = "okay";
pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
@@ -259,6 +432,12 @@
pinctrl-names = "default";
};
+&pdm {
+ pinctrl-0 = <&pdm_din0_z_pins>, <&pdm_dclk_z_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
&pwm_AO_ab {
status = "okay";
pinctrl-0 = <&pwm_ao_a_pins>;
@@ -305,6 +484,9 @@
non-removable;
disable-wp;
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
@@ -353,6 +535,54 @@
vqmmc-supply = <&emmc_1v8>;
};
+&tdmif_a {
+ pinctrl-0 = <&tdm_a_dout0_pins>, <&tdm_a_fs_pins>, <&tdm_a_sclk_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ assigned-clocks = <&clkc_audio AUD_CLKID_TDM_SCLK_PAD0>,
+ <&clkc_audio AUD_CLKID_TDM_LRCLK_PAD0>;
+ assigned-clock-parents = <&clkc_audio AUD_CLKID_MST_A_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_A_LRCLK>;
+ assigned-clock-rates = <0>, <0>;
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmin_a {
+ status = "okay";
+};
+
+&tdmin_b {
+ status = "okay";
+};
+
+&tdmout_a {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&toddr_a {
+ status = "okay";
+};
+
+&toddr_b {
+ status = "okay";
+};
+
+&toddr_c {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
+
&uart_A {
status = "okay";
pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
@@ -361,6 +591,8 @@
bluetooth {
compatible = "brcm,bcm43438-bt";
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <95 IRQ_TYPE_LEVEL_HIGH>;
shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
max-speed = <2000000>;
clocks = <&wifi32k>;
@@ -5,11 +5,47 @@
*/
#include "meson-g12-common.dtsi"
+#include <dt-bindings/clock/axg-audio-clkc.h>
#include <dt-bindings/power/meson-sm1-power.h>
+#include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
+#include <dt-bindings/reset/amlogic,meson-g12a-audio-reset.h>
/ {
compatible = "amlogic,sm1";
+ tdmif_a: audio-controller-0 {
+ compatible = "amlogic,axg-tdm-iface";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TDM_A";
+ clocks = <&clkc_audio AUD_CLKID_MST_A_MCLK>,
+ <&clkc_audio AUD_CLKID_MST_A_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_A_LRCLK>;
+ clock-names = "mclk", "sclk", "lrclk";
+ status = "disabled";
+ };
+
+ tdmif_b: audio-controller-1 {
+ compatible = "amlogic,axg-tdm-iface";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TDM_B";
+ clocks = <&clkc_audio AUD_CLKID_MST_B_MCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
+ clock-names = "mclk", "sclk", "lrclk";
+ status = "disabled";
+ };
+
+ tdmif_c: audio-controller-2 {
+ compatible = "amlogic,axg-tdm-iface";
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TDM_C";
+ clocks = <&clkc_audio AUD_CLKID_MST_C_MCLK>,
+ <&clkc_audio AUD_CLKID_MST_C_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_C_LRCLK>;
+ clock-names = "mclk", "sclk", "lrclk";
+ status = "disabled";
+ };
+
cpus {
#address-cells = <0x2>;
#size-cells = <0x0>;
@@ -117,6 +153,305 @@
};
};
+&apb {
+ audio: bus@60000 {
+ compatible = "simple-bus";
+ reg = <0x0 0x60000 0x0 0x1000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x60000 0x0 0x1000>;
+
+ clkc_audio: clock-controller@0 {
+ status = "disabled";
+ compatible = "amlogic,sm1-audio-clkc";
+ reg = <0x0 0x0 0x0 0xb4>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+
+ clocks = <&clkc CLKID_AUDIO>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>,
+ <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL3>,
+ <&clkc CLKID_HIFI_PLL>,
+ <&clkc CLKID_FCLK_DIV3>,
+ <&clkc CLKID_FCLK_DIV4>,
+ <&clkc CLKID_FCLK_DIV5>;
+ clock-names = "pclk",
+ "mst_in0",
+ "mst_in1",
+ "mst_in2",
+ "mst_in3",
+ "mst_in4",
+ "mst_in5",
+ "mst_in6",
+ "mst_in7";
+
+ resets = <&reset RESET_AUDIO>;
+ };
+
+ toddr_a: audio-controller@100 {
+ compatible = "amlogic,sm1-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x100 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_A";
+ interrupts = <GIC_SPI 148 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_A>;
+ resets = <&arb AXG_ARB_TODDR_A>,
+ <&clkc_audio AUD_RESET_TODDR_A>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <8192>;
+ status = "disabled";
+ };
+
+ toddr_b: audio-controller@140 {
+ compatible = "amlogic,sm1-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x140 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_B";
+ interrupts = <GIC_SPI 149 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_B>;
+ resets = <&arb AXG_ARB_TODDR_B>,
+ <&clkc_audio AUD_RESET_TODDR_B>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+
+ toddr_c: audio-controller@180 {
+ compatible = "amlogic,sm1-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x180 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_C";
+ interrupts = <GIC_SPI 150 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_C>;
+ resets = <&arb AXG_ARB_TODDR_C>,
+ <&clkc_audio AUD_RESET_TODDR_C>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+
+ frddr_a: audio-controller@1c0 {
+ compatible = "amlogic,sm1-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x1c0 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_A";
+ interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_A>;
+ resets = <&arb AXG_ARB_FRDDR_A>,
+ <&clkc_audio AUD_RESET_FRDDR_A>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <512>;
+ status = "disabled";
+ };
+
+ frddr_b: audio-controller@200 {
+ compatible = "amlogic,sm1-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x200 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_B";
+ interrupts = <GIC_SPI 153 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_B>;
+ resets = <&arb AXG_ARB_FRDDR_B>,
+ <&clkc_audio AUD_RESET_FRDDR_B>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+
+ frddr_c: audio-controller@240 {
+ compatible = "amlogic,sm1-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x240 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_C";
+ interrupts = <GIC_SPI 154 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_C>;
+ resets = <&arb AXG_ARB_FRDDR_C>,
+ <&clkc_audio AUD_RESET_FRDDR_C>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+
+ arb: reset-controller@280 {
+ status = "disabled";
+ compatible = "amlogic,meson-sm1-audio-arb";
+ reg = <0x0 0x280 0x0 0x4>;
+ #reset-cells = <1>;
+ clocks = <&clkc_audio AUD_CLKID_DDR_ARB>;
+ };
+
+ tdmin_a: audio-controller@300 {
+ compatible = "amlogic,sm1-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x300 0x0 0x40>;
+ sound-name-prefix = "TDMIN_A";
+ resets = <&clkc_audio AUD_RESET_TDMIN_A>;
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_A>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_A_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmin_b: audio-controller@340 {
+ compatible = "amlogic,sm1-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x340 0x0 0x40>;
+ sound-name-prefix = "TDMIN_B";
+ resets = <&clkc_audio AUD_RESET_TDMIN_B>;
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_B>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_B_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmin_c: audio-controller@380 {
+ compatible = "amlogic,sm1-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x380 0x0 0x40>;
+ sound-name-prefix = "TDMIN_C";
+ resets = <&clkc_audio AUD_RESET_TDMIN_C>;
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_C>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_C_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmin_lb: audio-controller@3c0 {
+ compatible = "amlogic,sm1-tdmin",
+ "amlogic,axg-tdmin";
+ reg = <0x0 0x3c0 0x0 0x40>;
+ sound-name-prefix = "TDMIN_LB";
+ resets = <&clkc_audio AUD_RESET_TDMIN_LB>;
+ clocks = <&clkc_audio AUD_CLKID_TDMIN_LB>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMIN_LB_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmout_a: audio-controller@500 {
+ compatible = "amlogic,sm1-tdmout";
+ reg = <0x0 0x500 0x0 0x40>;
+ sound-name-prefix = "TDMOUT_A";
+ resets = <&clkc_audio AUD_RESET_TDMOUT_A>;
+ clocks = <&clkc_audio AUD_CLKID_TDMOUT_A>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_A_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmout_b: audio-controller@540 {
+ compatible = "amlogic,sm1-tdmout";
+ reg = <0x0 0x540 0x0 0x40>;
+ sound-name-prefix = "TDMOUT_B";
+ resets = <&clkc_audio AUD_RESET_TDMOUT_B>;
+ clocks = <&clkc_audio AUD_CLKID_TDMOUT_B>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_B_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tdmout_c: audio-controller@580 {
+ compatible = "amlogic,sm1-tdmout";
+ reg = <0x0 0x580 0x0 0x40>;
+ sound-name-prefix = "TDMOUT_C";
+ resets = <&clkc_audio AUD_RESET_TDMOUT_C>;
+ clocks = <&clkc_audio AUD_CLKID_TDMOUT_C>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_SCLK_SEL>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>,
+ <&clkc_audio AUD_CLKID_TDMOUT_C_LRCLK>;
+ clock-names = "pclk", "sclk", "sclk_sel",
+ "lrclk", "lrclk_sel";
+ status = "disabled";
+ };
+
+ tohdmitx: audio-controller@744 {
+ compatible = "amlogic,sm1-tohdmitx",
+ "amlogic,g12a-tohdmitx";
+ reg = <0x0 0x744 0x0 0x4>;
+ #sound-dai-cells = <1>;
+ sound-name-prefix = "TOHDMITX";
+ resets = <&clkc_audio AUD_RESET_TOHDMITX>;
+ status = "disabled";
+ };
+
+ toddr_d: audio-controller@840 {
+ compatible = "amlogic,sm1-toddr",
+ "amlogic,axg-toddr";
+ reg = <0x0 0x840 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TODDR_D";
+ interrupts = <GIC_SPI 49 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_TODDR_D>;
+ resets = <&arb AXG_ARB_TODDR_D>,
+ <&clkc_audio AUD_RESET_TODDR_D>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+
+ frddr_d: audio-controller@880 {
+ compatible = "amlogic,sm1-frddr",
+ "amlogic,axg-frddr";
+ reg = <0x0 0x880 0x0 0x2c>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "FRDDR_D";
+ interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_audio AUD_CLKID_FRDDR_D>;
+ resets = <&arb AXG_ARB_FRDDR_D>,
+ <&clkc_audio AUD_RESET_FRDDR_D>;
+ reset-names = "arb", "rst";
+ amlogic,fifo-depth = <256>;
+ status = "disabled";
+ };
+ };
+
+ pdm: audio-controller@61000 {
+ compatible = "amlogic,sm1-pdm",
+ "amlogic,axg-pdm";
+ reg = <0x0 0x61000 0x0 0x34>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "PDM";
+ clocks = <&clkc_audio AUD_CLKID_PDM>,
+ <&clkc_audio AUD_CLKID_PDM_DCLK>,
+ <&clkc_audio AUD_CLKID_PDM_SYSCLK>;
+ clock-names = "pclk", "dclk", "sysclk";
+ status = "disabled";
+ };
+};
+
&cecb_AO {
compatible = "amlogic,meson-sm1-ao-cec";
};
@@ -134,10 +469,31 @@
power-domains = <&pwrc PWRC_SM1_ETH_ID>;
};
+&gpio_intc {
+ compatible = "amlogic,meson-sm1-gpio-intc",
+ "amlogic,meson-gpio-intc";
+};
+
+&pcie {
+ power-domains = <&pwrc PWRC_SM1_PCIE_ID>;
+};
+
&pwrc {
compatible = "amlogic,meson-sm1-pwrc";
};
+&simplefb_cvbs {
+ power-domains = <&pwrc PWRC_SM1_VPU_ID>;
+};
+
+&simplefb_hdmi {
+ power-domains = <&pwrc PWRC_SM1_VPU_ID>;
+};
+
+&vdec {
+ compatible = "amlogic,sm1-vdec";
+};
+
&vpu {
power-domains = <&pwrc PWRC_SM1_VPU_ID>;
};
@@ -80,5 +80,15 @@
#define AUD_CLKID_TDM_SCLK_PAD0 160
#define AUD_CLKID_TDM_SCLK_PAD1 161
#define AUD_CLKID_TDM_SCLK_PAD2 162
+#define AUD_CLKID_TOP 163
+#define AUD_CLKID_TORAM 164
+#define AUD_CLKID_EQDRC 165
+#define AUD_CLKID_RESAMPLE_B 166
+#define AUD_CLKID_TOVAD 167
+#define AUD_CLKID_LOCKER 168
+#define AUD_CLKID_SPDIFIN_LB 169
+#define AUD_CLKID_FRDDR_D 170
+#define AUD_CLKID_TODDR_D 171
+#define AUD_CLKID_LOOPBACK_B 172
#endif /* __AXG_AUDIO_CLKC_BINDINGS_H */
@@ -63,5 +63,12 @@
#define CLKID_AO_UART2 4
#define CLKID_AO_IR_BLASTER 5
#define CLKID_AO_CEC_32K 6
+#define CLKID_AO_CTS_OSCIN 7
+#define CLKID_AO_32K_PRE 8
+#define CLKID_AO_32K_DIV 9
+#define CLKID_AO_32K_SEL 10
+#define CLKID_AO_32K 11
+#define CLKID_AO_CTS_RTC_OSCIN 12
+#define CLKID_AO_CLK81 13
#endif
@@ -125,5 +125,26 @@
#define CLKID_VAPB_1 138
#define CLKID_VAPB_SEL 139
#define CLKID_VAPB 140
+#define CLKID_VDEC_1 153
+#define CLKID_VDEC_HEVC 156
+#define CLKID_GEN_CLK 159
+#define CLKID_VID_PLL 166
+#define CLKID_VCLK 175
+#define CLKID_VCLK2 176
+#define CLKID_VCLK_DIV1 185
+#define CLKID_VCLK_DIV2 186
+#define CLKID_VCLK_DIV4 187
+#define CLKID_VCLK_DIV6 188
+#define CLKID_VCLK_DIV12 189
+#define CLKID_VCLK2_DIV1 190
+#define CLKID_VCLK2_DIV2 191
+#define CLKID_VCLK2_DIV4 192
+#define CLKID_VCLK2_DIV6 193
+#define CLKID_VCLK2_DIV12 194
+#define CLKID_CTS_ENCI 199
+#define CLKID_CTS_ENCP 200
+#define CLKID_CTS_VDAC 201
+#define CLKID_HDMI_TX 202
+#define CLKID_HDMI 205
#endif /* __GXBB_CLKC_H */
@@ -1,15 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
/*
* GPIO definitions for Amlogic Meson GXBB SoCs
*
* Copyright (C) 2016 Endless Mobile, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef _DT_BINDINGS_MESON_GXBB_GPIO_H
@@ -1,15 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
/*
* GPIO definitions for Amlogic Meson GXL SoCs
*
* Copyright (C) 2016 Endless Mobile, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef _DT_BINDINGS_MESON_GXL_GPIO_H
@@ -13,5 +13,7 @@
#define AXG_ARB_FRDDR_A 3
#define AXG_ARB_FRDDR_B 4
#define AXG_ARB_FRDDR_C 5
+#define AXG_ARB_TODDR_D 6
+#define AXG_ARB_FRDDR_D 7
#endif /* _DT_BINDINGS_AMLOGIC_MESON_AXG_AUDIO_ARB_H */
@@ -1,12 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause */
/*
- *
* Copyright (c) 2016 BayLibre, SAS.
* Author: Neil Armstrong <narmstrong@baylibre.com>
*
* Copyright (c) 2017 Amlogic, inc.
* Author: Yixun Lan <yixun.lan@amlogic.com>
*
- * SPDX-License-Identifier: (GPL-2.0+ OR BSD)
*/
#ifndef _DT_BINDINGS_AMLOGIC_MESON_AXG_RESET_H
@@ -35,4 +35,19 @@
#define AUD_RESET_TOHDMITX 24
#define AUD_RESET_CLKTREE 25
+/* SM1 added resets */
+#define AUD_RESET_RESAMPLE_B 26
+#define AUD_RESET_TOVAD 27
+#define AUD_RESET_LOCKER 28
+#define AUD_RESET_SPDIFIN_LB 29
+#define AUD_RESET_FRATV 30
+#define AUD_RESET_FRHDMIRX 31
+#define AUD_RESET_FRDDR_D 32
+#define AUD_RESET_TODDR_D 33
+#define AUD_RESET_LOOPBACK_B 34
+#define AUD_RESET_EARCTX 35
+#define AUD_RESET_EARCRX 36
+#define AUD_RESET_FRDDR_E 37
+#define AUD_RESET_TODDR_E 38
+
#endif
@@ -1,56 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
/*
- * This file is provided under a dual BSD/GPLv2 license. When using or
- * redistributing this file, you may do so under either license.
- *
- * GPL LICENSE SUMMARY
- *
* Copyright (c) 2016 BayLibre, SAS.
* Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of version 2 of the GNU General Public License as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see <http://www.gnu.org/licenses/>.
- * The full GNU General Public License is included in this distribution
- * in the file called COPYING.
- *
- * BSD LICENSE
- *
- * Copyright (c) 2016 BayLibre, SAS.
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in
- * the documentation and/or other materials provided with the
- * distribution.
- * * Neither the name of Intel Corporation nor the names of its
- * contributors may be used to endorse or promote products derived
- * from this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H
#define _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H
Sync the device tree and dt-bindings from Linux v5.6-rc2 11a48a5a18c6 ("Linux 5.6-rc2") The only exception to this is the mmc pinctrl pin bias of gxl SoC family. This is a fix which found its way to u-boot but not Linux yet. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- arch/arm/dts/meson-axg-s400.dts | 70 ++- arch/arm/dts/meson-axg.dtsi | 273 ++++++++-- arch/arm/dts/meson-g12-common.dtsi | 478 ++++++------------ arch/arm/dts/meson-g12.dtsi | 398 +++++++++++++++ arch/arm/dts/meson-g12a-sei510.dts | 64 +++ arch/arm/dts/meson-g12a-u200.dts | 54 ++ arch/arm/dts/meson-g12a.dtsi | 33 +- arch/arm/dts/meson-g12b-a311d-khadas-vim3.dts | 25 + arch/arm/dts/meson-g12b-odroid-n2.dts | 2 +- arch/arm/dts/meson-g12b.dtsi | 26 +- arch/arm/dts/meson-gx.dtsi | 87 +++- arch/arm/dts/meson-gxbb-nanopi-k2.dts | 26 +- arch/arm/dts/meson-gxbb-odroidc2.dts | 100 +++- arch/arm/dts/meson-gxbb-p200.dts | 9 +- arch/arm/dts/meson-gxbb-p201.dts | 2 +- arch/arm/dts/meson-gxbb-p20x.dtsi | 9 +- arch/arm/dts/meson-gxbb.dtsi | 118 ++++- arch/arm/dts/meson-gxl-s805x-libretech-ac.dts | 2 +- arch/arm/dts/meson-gxl-s905x-khadas-vim.dts | 20 +- arch/arm/dts/meson-gxl-s905x-libretech-cc.dts | 26 +- arch/arm/dts/meson-gxl-s905x-p212.dtsi | 10 +- arch/arm/dts/meson-gxl.dtsi | 76 ++- arch/arm/dts/meson-gxm-khadas-vim2.dts | 71 +-- arch/arm/dts/meson-gxm.dtsi | 39 +- arch/arm/dts/meson-khadas-vim3.dtsi | 7 + arch/arm/dts/meson-sm1-khadas-vim3l.dts | 95 ++++ arch/arm/dts/meson-sm1-sei610.dts | 236 ++++++++- arch/arm/dts/meson-sm1.dtsi | 356 +++++++++++++ include/dt-bindings/clock/axg-audio-clkc.h | 10 + include/dt-bindings/clock/gxbb-aoclkc.h | 7 + include/dt-bindings/clock/gxbb-clkc.h | 21 + include/dt-bindings/gpio/meson-gxbb-gpio.h | 8 +- include/dt-bindings/gpio/meson-gxl-gpio.h | 8 +- .../reset/amlogic,meson-axg-audio-arb.h | 2 + .../reset/amlogic,meson-axg-reset.h | 3 +- .../reset/amlogic,meson-g12a-audio-reset.h | 15 + .../reset/amlogic,meson-gxbb-reset.h | 51 +- 37 files changed, 2214 insertions(+), 623 deletions(-) create mode 100644 arch/arm/dts/meson-g12.dtsi create mode 100644 arch/arm/dts/meson-sm1-khadas-vim3l.dts