| Message ID | 20191122104505.8986-3-vidyas@nvidia.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add support for PCIe endpoint mode in Tegra194 | expand |
On Fri, Nov 22, 2019 at 04:15:01PM +0530, Vidya Sagar wrote: > Add support for PCIe controllers that can operate in endpoint mode > in Tegra194. > > Signed-off-by: Vidya Sagar <vidyas@nvidia.com> > --- > .../bindings/pci/nvidia,tegra194-pcie-ep.txt | 138 ++++++++++++++++++ > 1 file changed, 138 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt The vast majority of this is a duplication of the host mode device tree bindings. I think it'd be best to combine both and only highlight where both modes differ. The designware-pcie.txt binding does something similar. > diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > new file mode 100644 > index 000000000000..4676ccf7dfa5 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > @@ -0,0 +1,138 @@ > +NVIDIA Tegra PCIe Endpoint mode controller (Synopsys DesignWare Core based) > + > +Some of the PCIe controllers which are based on Synopsys DesignWare PCIe IP > +are dual mode i.e. they can work in root port mode or endpoint mode but one > + at a time. Since they are based on DesignWare IP, they inherit all the common > +properties defined in designware-pcie.txt. > + > +Required properties: > +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". The device tree snippets that you added have "nvidia,tegra194-pcie-ep" for EP mode controllers. So either this is wrong or the DTS files are wrong. This device tree binding describes the exact same hardware, so I don't think we necessarily need two different compatible strings. It's fairly easy to distinguish between which mode to run in by looking at which properties exist. EP mode for example is the only one that uses the "addr_space" reg entry. Rob, do you know why a different compatible string was chosen for the EP mode? Looking at the driver, there are only a handful of differences in the programming, but most of the driver remains identical. An extra DT compatible string seems a bit exaggerated since it suggests that this is actually different hardware, where it clearly isn't. > + Tegra194: Only C0, C4 & C5 controllers are dual mode controllers. > +- power-domains: A phandle to the node that controls power to the respective > + PCIe controller and a specifier name for the PCIe controller. Following are > + the specifiers for the different PCIe controllers > + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 > + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 > + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 > + these specifiers are defined in > + "include/dt-bindings/power/tegra194-powergate.h" file. > +- reg: A list of physical base address and length pairs for each set of > + controller registers. Must contain an entry for each entry in the reg-names > + property. > +- reg-names: Must include the following entries: > + "appl": Controller's application logic registers > + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address > + Translation Unit) registers of the PCIe core are made available > + for SW access. > + "dbi": The aperture where root port's own configuration registers are > + available > + "addr_space": Used to map remote RC address space > +- interrupts: A list of interrupt outputs of the controller. Must contain an > + entry for each entry in the interrupt-names property. > +- interrupt-names: Must include the following entry: > + "intr": The Tegra interrupt that is asserted for controller interrupts > +- clocks: Must contain an entry for each entry in clock-names. > + See ../clocks/clock-bindings.txt for details. > +- clock-names: Must include the following entries: > + - core > +- resets: Must contain an entry for each entry in reset-names. > + See ../reset/reset.txt for details. > +- reset-names: Must include the following entries: > + - apb > + - core > +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. > +- phy-names: Must include an entry for each active lane. > + "p2u-N": where N ranges from 0 to one less than the total number of lanes > +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed > + by controller-id. Following are the controller ids for each controller. > + 0: C0 > + 4: C4 > + 5: C5 > +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals > +- nvidia,pex-rst-gpio: Must contain a phandle to a GPIO controller followed by > + GPIO that is being used as PERST signal Why is this NVIDIA specific? Do other instantiations of the DW IP not also need a means to define which GPIO is the reset? > + > +Optional properties: > +- pinctrl-names: A list of pinctrl state names. > + It is mandatory for C5 controller and optional for other controllers. > + - "default": Configures PCIe I/O for proper operation. > +- pinctrl-0: phandle for the 'default' state of pin configuration. > + It is mandatory for C5 controller and optional for other controllers. > +- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt > +- nvidia,update-fc-fixup: This is a boolean property and needs to be present to > + improve performance when a platform is designed in such a way that it > + satisfies at least one of the following conditions thereby enabling root > + port to exchange optimum number of FC (Flow Control) credits with > + downstream devices > + 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS) > + 2. If C0/C4/C5 operate at their respective max link widths and > + a) speed is Gen-2 and MPS is 256B > + b) speed is >= Gen-3 with any MPS > +- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM > + to be specified in microseconds > +- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be > + specified in microseconds > +- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be > + specified in microseconds > + > +NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to > +operate in the endpoint mode because of the way the platform is designed. > +There is a mux that needs to be programmed to let the REFCLK from the host to > +flow into C5 controller when it operates in the endpoint mode. This mux is > +controlled by the GPIO (AA, 5) and it needs to be driven 'high'. For this to > +happen, set status of "pex-refclk-sel-high" node under "gpio@c2f0000" node to > +'okay'. > + When any dual mode controller is made to operate in the endpoint mode, > +please make sure that its respective root port node's status is set to > +'disabled'. This seems very brittle to me. There's no good way how we can detect such misconfigurations. If instead we only have one node describing the hardware fully, the chances of configuring things wrong (by for example enabling both the host and EP mode device tree nodes) can be reduced. So I think instead of duplicating all of the device tree content to have both a host and an EP node for each controller, it'd be better to just have a single node and let the device tree bindings specify which changes to apply to switch into EP mode. For example, there should be nothing wrong with specifying some of the EP-only properties (like num-ib-windows and num-ob-windows) all the time and only use them when we actually run in EP mode. As I mentioned earlier, there are a couple of easy ways to distinguish the modes. The presence of the "addr_space" reg entry is one example, but we could also key off the nvidia,pex-rst-gpio property, since that (presumably) wouldn't be needed for host mode. That way we can just add default, host mode entries to tegra194.dtsi and whenever somebody wants to enable EP mode, they can just override the node in the board-level DTS file, like so: pcie@141a0000 { reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ reg-names = "appl", "atu_dma", "dbi", "addr_space"; nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; }; Thierry > + > +Examples: > +========= > + > +Tegra194: > +-------- > + > + pcie_ep@141a0000 { > + compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep"; > + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>; > + reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ > + 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ > + 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ > + 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ > + reg-names = "appl", "atu_dma", "dbi", "addr_space"; > + > + num-lanes = <8>; > + num-ib-windows = <2>; > + num-ob-windows = <8>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&clkreq_c5_bi_dir_state>; > + > + clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>; > + clock-names = "core"; > + > + resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>, > + <&bpmp TEGRA194_RESET_PEX1_CORE_5>; > + reset-names = "apb", "core"; > + > + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ > + interrupt-names = "intr"; > + > + nvidia,bpmp = <&bpmp 5>; > + > + nvidia,aspm-cmrt-us = <60>; > + nvidia,aspm-pwr-on-t-us = <20>; > + nvidia,aspm-l0s-entrance-latency-us = <3>; > + > + vddio-pex-ctl-supply = <&vdd_1v8ao>; > + > + nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) > + GPIO_ACTIVE_LOW>; > + > + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, > + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, > + <&p2u_nvhs_6>, <&p2u_nvhs_7>; > + > + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", > + "p2u-5", "p2u-6", "p2u-7"; > + }; > -- > 2.17.1 >
On 11/22/2019 6:49 PM, Thierry Reding wrote: > On Fri, Nov 22, 2019 at 04:15:01PM +0530, Vidya Sagar wrote: >> Add support for PCIe controllers that can operate in endpoint mode >> in Tegra194. >> >> Signed-off-by: Vidya Sagar <vidyas@nvidia.com> >> --- >> .../bindings/pci/nvidia,tegra194-pcie-ep.txt | 138 ++++++++++++++++++ >> 1 file changed, 138 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > The vast majority of this is a duplication of the host mode device tree > bindings. I think it'd be best to combine both and only highlight where > both modes differ. > > The designware-pcie.txt binding does something similar. Ok. I'll merge this into the host mode bindings file and in that differentiate between root mode and endpoint mode. > >> diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt >> new file mode 100644 >> index 000000000000..4676ccf7dfa5 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt >> @@ -0,0 +1,138 @@ >> +NVIDIA Tegra PCIe Endpoint mode controller (Synopsys DesignWare Core based) >> + >> +Some of the PCIe controllers which are based on Synopsys DesignWare PCIe IP >> +are dual mode i.e. they can work in root port mode or endpoint mode but one >> + at a time. Since they are based on DesignWare IP, they inherit all the common >> +properties defined in designware-pcie.txt. >> + >> +Required properties: >> +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". > > The device tree snippets that you added have "nvidia,tegra194-pcie-ep" > for EP mode controllers. So either this is wrong or the DTS files are > wrong. DTS file are correct. This is a mistake in this file. I'll correct this. > > This device tree binding describes the exact same hardware, so I don't > think we necessarily need two different compatible strings. It's fairly > easy to distinguish between which mode to run in by looking at which > properties exist. EP mode for example is the only one that uses the > "addr_space" reg entry. > > Rob, do you know why a different compatible string was chosen for the EP > mode? Looking at the driver, there are only a handful of differences in > the programming, but most of the driver remains identical. An extra DT > compatible string seems a bit exaggerated since it suggests that this is > actually different hardware, where it clearly isn't. Since all other implementations have done it this way, I just followed to be in sync with them. Even I would also like to hear from Rob on the rationale behind this. > >> + Tegra194: Only C0, C4 & C5 controllers are dual mode controllers. >> +- power-domains: A phandle to the node that controls power to the respective >> + PCIe controller and a specifier name for the PCIe controller. Following are >> + the specifiers for the different PCIe controllers >> + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 >> + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 >> + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 >> + these specifiers are defined in >> + "include/dt-bindings/power/tegra194-powergate.h" file. >> +- reg: A list of physical base address and length pairs for each set of >> + controller registers. Must contain an entry for each entry in the reg-names >> + property. >> +- reg-names: Must include the following entries: >> + "appl": Controller's application logic registers >> + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address >> + Translation Unit) registers of the PCIe core are made available >> + for SW access. >> + "dbi": The aperture where root port's own configuration registers are >> + available >> + "addr_space": Used to map remote RC address space >> +- interrupts: A list of interrupt outputs of the controller. Must contain an >> + entry for each entry in the interrupt-names property. >> +- interrupt-names: Must include the following entry: >> + "intr": The Tegra interrupt that is asserted for controller interrupts >> +- clocks: Must contain an entry for each entry in clock-names. >> + See ../clocks/clock-bindings.txt for details. >> +- clock-names: Must include the following entries: >> + - core >> +- resets: Must contain an entry for each entry in reset-names. >> + See ../reset/reset.txt for details. >> +- reset-names: Must include the following entries: >> + - apb >> + - core >> +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. >> +- phy-names: Must include an entry for each active lane. >> + "p2u-N": where N ranges from 0 to one less than the total number of lanes >> +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed >> + by controller-id. Following are the controller ids for each controller. >> + 0: C0 >> + 4: C4 >> + 5: C5 >> +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals >> +- nvidia,pex-rst-gpio: Must contain a phandle to a GPIO controller followed by >> + GPIO that is being used as PERST signal > > Why is this NVIDIA specific? Do other instantiations of the DW IP not > also need a means to define which GPIO is the reset? I'm not sure. At least I didn't find anything like this in other implementations. My understanding is that, controller handles assert/de-assert on the PERST line automatically without SW intervention. I think it is for the same reason that other implementations don't wait for the REFCLK to flow in from host to configure the IP. I think they just use some internal clock for the configuration and switch to running the core based on REFCLK as and when it is available (i.e. whenever a de-assert is perceived on PERST line by the controller) > >> + >> +Optional properties: >> +- pinctrl-names: A list of pinctrl state names. >> + It is mandatory for C5 controller and optional for other controllers. >> + - "default": Configures PCIe I/O for proper operation. >> +- pinctrl-0: phandle for the 'default' state of pin configuration. >> + It is mandatory for C5 controller and optional for other controllers. >> +- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt >> +- nvidia,update-fc-fixup: This is a boolean property and needs to be present to >> + improve performance when a platform is designed in such a way that it >> + satisfies at least one of the following conditions thereby enabling root >> + port to exchange optimum number of FC (Flow Control) credits with >> + downstream devices >> + 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS) >> + 2. If C0/C4/C5 operate at their respective max link widths and >> + a) speed is Gen-2 and MPS is 256B >> + b) speed is >= Gen-3 with any MPS >> +- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM >> + to be specified in microseconds >> +- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be >> + specified in microseconds >> +- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be >> + specified in microseconds >> + >> +NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to >> +operate in the endpoint mode because of the way the platform is designed. >> +There is a mux that needs to be programmed to let the REFCLK from the host to >> +flow into C5 controller when it operates in the endpoint mode. This mux is >> +controlled by the GPIO (AA, 5) and it needs to be driven 'high'. For this to >> +happen, set status of "pex-refclk-sel-high" node under "gpio@c2f0000" node to >> +'okay'. >> + When any dual mode controller is made to operate in the endpoint mode, >> +please make sure that its respective root port node's status is set to >> +'disabled'. > > This seems very brittle to me. There's no good way how we can detect > such misconfigurations. If instead we only have one node describing the > hardware fully, the chances of configuring things wrong (by for example > enabling both the host and EP mode device tree nodes) can be reduced. > > So I think instead of duplicating all of the device tree content to have > both a host and an EP node for each controller, it'd be better to just > have a single node and let the device tree bindings specify which > changes to apply to switch into EP mode. > > For example, there should be nothing wrong with specifying some of the > EP-only properties (like num-ib-windows and num-ob-windows) all the time > and only use them when we actually run in EP mode. > > As I mentioned earlier, there are a couple of easy ways to distinguish > the modes. The presence of the "addr_space" reg entry is one example, > but we could also key off the nvidia,pex-rst-gpio property, since that > (presumably) wouldn't be needed for host mode. > > That way we can just add default, host mode entries to tegra194.dtsi and > whenever somebody wants to enable EP mode, they can just override the > node in the board-level DTS file, like so: > > pcie@141a0000 { > reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ > 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ > 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ > 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ > reg-names = "appl", "atu_dma", "dbi", "addr_space"; > > nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; > }; > > Thierry I like it and fine with making these modifications also but would like to hear from Rob also on this. - Vidya Sagar > >> + >> +Examples: >> +========= >> + >> +Tegra194: >> +-------- >> + >> + pcie_ep@141a0000 { >> + compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep"; >> + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>; >> + reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ >> + 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ >> + 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ >> + 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ >> + reg-names = "appl", "atu_dma", "dbi", "addr_space"; >> + >> + num-lanes = <8>; >> + num-ib-windows = <2>; >> + num-ob-windows = <8>; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&clkreq_c5_bi_dir_state>; >> + >> + clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>; >> + clock-names = "core"; >> + >> + resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>, >> + <&bpmp TEGRA194_RESET_PEX1_CORE_5>; >> + reset-names = "apb", "core"; >> + >> + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ >> + interrupt-names = "intr"; >> + >> + nvidia,bpmp = <&bpmp 5>; >> + >> + nvidia,aspm-cmrt-us = <60>; >> + nvidia,aspm-pwr-on-t-us = <20>; >> + nvidia,aspm-l0s-entrance-latency-us = <3>; >> + >> + vddio-pex-ctl-supply = <&vdd_1v8ao>; >> + >> + nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) >> + GPIO_ACTIVE_LOW>; >> + >> + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, >> + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, >> + <&p2u_nvhs_6>, <&p2u_nvhs_7>; >> + >> + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", >> + "p2u-5", "p2u-6", "p2u-7"; >> + }; >> -- >> 2.17.1 >>
On Mon, Nov 25, 2019 at 12:53:42PM +0530, Vidya Sagar wrote: > On 11/22/2019 6:49 PM, Thierry Reding wrote: > > On Fri, Nov 22, 2019 at 04:15:01PM +0530, Vidya Sagar wrote: > > > Add support for PCIe controllers that can operate in endpoint mode > > > in Tegra194. > > > > > > Signed-off-by: Vidya Sagar <vidyas@nvidia.com> > > > --- > > > .../bindings/pci/nvidia,tegra194-pcie-ep.txt | 138 ++++++++++++++++++ > > > 1 file changed, 138 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > > > The vast majority of this is a duplication of the host mode device tree > > bindings. I think it'd be best to combine both and only highlight where > > both modes differ. > > > > The designware-pcie.txt binding does something similar. > Ok. I'll merge this into the host mode bindings file and in that differentiate between > root mode and endpoint mode. > > > > > > diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > > new file mode 100644 > > > index 000000000000..4676ccf7dfa5 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > > @@ -0,0 +1,138 @@ > > > +NVIDIA Tegra PCIe Endpoint mode controller (Synopsys DesignWare Core based) > > > + > > > +Some of the PCIe controllers which are based on Synopsys DesignWare PCIe IP > > > +are dual mode i.e. they can work in root port mode or endpoint mode but one > > > + at a time. Since they are based on DesignWare IP, they inherit all the common > > > +properties defined in designware-pcie.txt. > > > + > > > +Required properties: > > > +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". > > > > The device tree snippets that you added have "nvidia,tegra194-pcie-ep" > > for EP mode controllers. So either this is wrong or the DTS files are > > wrong. > DTS file are correct. This is a mistake in this file. I'll correct this. > > > > > This device tree binding describes the exact same hardware, so I don't > > think we necessarily need two different compatible strings. It's fairly > > easy to distinguish between which mode to run in by looking at which > > properties exist. EP mode for example is the only one that uses the > > "addr_space" reg entry. > > > > Rob, do you know why a different compatible string was chosen for the EP > > mode? Looking at the driver, there are only a handful of differences in > > the programming, but most of the driver remains identical. An extra DT > > compatible string seems a bit exaggerated since it suggests that this is > > actually different hardware, where it clearly isn't. > Since all other implementations have done it this way, I just followed to be in sync > with them. Even I would also like to hear from Rob on the rationale behind this. > > > > > > + Tegra194: Only C0, C4 & C5 controllers are dual mode controllers. > > > +- power-domains: A phandle to the node that controls power to the respective > > > + PCIe controller and a specifier name for the PCIe controller. Following are > > > + the specifiers for the different PCIe controllers > > > + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 > > > + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 > > > + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 > > > + these specifiers are defined in > > > + "include/dt-bindings/power/tegra194-powergate.h" file. > > > +- reg: A list of physical base address and length pairs for each set of > > > + controller registers. Must contain an entry for each entry in the reg-names > > > + property. > > > +- reg-names: Must include the following entries: > > > + "appl": Controller's application logic registers > > > + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address > > > + Translation Unit) registers of the PCIe core are made available > > > + for SW access. > > > + "dbi": The aperture where root port's own configuration registers are > > > + available > > > + "addr_space": Used to map remote RC address space > > > +- interrupts: A list of interrupt outputs of the controller. Must contain an > > > + entry for each entry in the interrupt-names property. > > > +- interrupt-names: Must include the following entry: > > > + "intr": The Tegra interrupt that is asserted for controller interrupts > > > +- clocks: Must contain an entry for each entry in clock-names. > > > + See ../clocks/clock-bindings.txt for details. > > > +- clock-names: Must include the following entries: > > > + - core > > > +- resets: Must contain an entry for each entry in reset-names. > > > + See ../reset/reset.txt for details. > > > +- reset-names: Must include the following entries: > > > + - apb > > > + - core > > > +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. > > > +- phy-names: Must include an entry for each active lane. > > > + "p2u-N": where N ranges from 0 to one less than the total number of lanes > > > +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed > > > + by controller-id. Following are the controller ids for each controller. > > > + 0: C0 > > > + 4: C4 > > > + 5: C5 > > > +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals > > > +- nvidia,pex-rst-gpio: Must contain a phandle to a GPIO controller followed by > > > + GPIO that is being used as PERST signal > > > > Why is this NVIDIA specific? Do other instantiations of the DW IP not > > also need a means to define which GPIO is the reset? > I'm not sure. At least I didn't find anything like this in other implementations. > My understanding is that, controller handles assert/de-assert on the PERST line > automatically without SW intervention. I think it is for the same reason that other > implementations don't wait for the REFCLK to flow in from host to configure the IP. > I think they just use some internal clock for the configuration and switch to > running the core based on REFCLK as and when it is available > (i.e. whenever a de-assert is perceived on PERST line by the controller) That would be somewhat surprising, though. The IP used in Tegra must be pretty close to the IP used in other SoCs, and the code that we need in pex_ep_event_pex_rst_{assert,deassert}() is pretty significant. Why the other instantiations wouldn't need something similar seems unlikely to me. Perhaps Jingoo or Gustavo can shed some light on this. Thierry > > > > > > + > > > +Optional properties: > > > +- pinctrl-names: A list of pinctrl state names. > > > + It is mandatory for C5 controller and optional for other controllers. > > > + - "default": Configures PCIe I/O for proper operation. > > > +- pinctrl-0: phandle for the 'default' state of pin configuration. > > > + It is mandatory for C5 controller and optional for other controllers. > > > +- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt > > > +- nvidia,update-fc-fixup: This is a boolean property and needs to be present to > > > + improve performance when a platform is designed in such a way that it > > > + satisfies at least one of the following conditions thereby enabling root > > > + port to exchange optimum number of FC (Flow Control) credits with > > > + downstream devices > > > + 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS) > > > + 2. If C0/C4/C5 operate at their respective max link widths and > > > + a) speed is Gen-2 and MPS is 256B > > > + b) speed is >= Gen-3 with any MPS > > > +- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM > > > + to be specified in microseconds > > > +- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be > > > + specified in microseconds > > > +- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be > > > + specified in microseconds > > > + > > > +NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to > > > +operate in the endpoint mode because of the way the platform is designed. > > > +There is a mux that needs to be programmed to let the REFCLK from the host to > > > +flow into C5 controller when it operates in the endpoint mode. This mux is > > > +controlled by the GPIO (AA, 5) and it needs to be driven 'high'. For this to > > > +happen, set status of "pex-refclk-sel-high" node under "gpio@c2f0000" node to > > > +'okay'. > > > + When any dual mode controller is made to operate in the endpoint mode, > > > +please make sure that its respective root port node's status is set to > > > +'disabled'. > > > > This seems very brittle to me. There's no good way how we can detect > > such misconfigurations. If instead we only have one node describing the > > hardware fully, the chances of configuring things wrong (by for example > > enabling both the host and EP mode device tree nodes) can be reduced. > > > > So I think instead of duplicating all of the device tree content to have > > both a host and an EP node for each controller, it'd be better to just > > have a single node and let the device tree bindings specify which > > changes to apply to switch into EP mode. > > > > For example, there should be nothing wrong with specifying some of the > > EP-only properties (like num-ib-windows and num-ob-windows) all the time > > and only use them when we actually run in EP mode. > > > > As I mentioned earlier, there are a couple of easy ways to distinguish > > the modes. The presence of the "addr_space" reg entry is one example, > > but we could also key off the nvidia,pex-rst-gpio property, since that > > (presumably) wouldn't be needed for host mode. > > > > That way we can just add default, host mode entries to tegra194.dtsi and > > whenever somebody wants to enable EP mode, they can just override the > > node in the board-level DTS file, like so: > > > > pcie@141a0000 { > > reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ > > 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ > > 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ > > 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ > > reg-names = "appl", "atu_dma", "dbi", "addr_space"; > > > > nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; > > }; > > > > Thierry > I like it and fine with making these modifications also but would like to hear from Rob > also on this. > > - Vidya Sagar > > > > > + > > > +Examples: > > > +========= > > > + > > > +Tegra194: > > > +-------- > > > + > > > + pcie_ep@141a0000 { > > > + compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep"; > > > + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>; > > > + reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ > > > + 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ > > > + 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ > > > + 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ > > > + reg-names = "appl", "atu_dma", "dbi", "addr_space"; > > > + > > > + num-lanes = <8>; > > > + num-ib-windows = <2>; > > > + num-ob-windows = <8>; > > > + > > > + pinctrl-names = "default"; > > > + pinctrl-0 = <&clkreq_c5_bi_dir_state>; > > > + > > > + clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>; > > > + clock-names = "core"; > > > + > > > + resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>, > > > + <&bpmp TEGRA194_RESET_PEX1_CORE_5>; > > > + reset-names = "apb", "core"; > > > + > > > + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ > > > + interrupt-names = "intr"; > > > + > > > + nvidia,bpmp = <&bpmp 5>; > > > + > > > + nvidia,aspm-cmrt-us = <60>; > > > + nvidia,aspm-pwr-on-t-us = <20>; > > > + nvidia,aspm-l0s-entrance-latency-us = <3>; > > > + > > > + vddio-pex-ctl-supply = <&vdd_1v8ao>; > > > + > > > + nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) > > > + GPIO_ACTIVE_LOW>; > > > + > > > + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, > > > + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, > > > + <&p2u_nvhs_6>, <&p2u_nvhs_7>; > > > + > > > + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", > > > + "p2u-5", "p2u-6", "p2u-7"; > > > + }; > > > -- > > > 2.17.1 > > > >
On Mon, Nov 25, 2019 at 7:33:59, Thierry Reding <thierry.reding@gmail.com> wrote: > On Mon, Nov 25, 2019 at 12:53:42PM +0530, Vidya Sagar wrote: > > On 11/22/2019 6:49 PM, Thierry Reding wrote: > > > On Fri, Nov 22, 2019 at 04:15:01PM +0530, Vidya Sagar wrote: > > > > Add support for PCIe controllers that can operate in endpoint mode > > > > in Tegra194. > > > > > > > > Signed-off-by: Vidya Sagar <vidyas@nvidia.com> > > > > --- > > > > .../bindings/pci/nvidia,tegra194-pcie-ep.txt | 138 ++++++++++++++++++ > > > > 1 file changed, 138 insertions(+) > > > > create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > > > > > The vast majority of this is a duplication of the host mode device tree > > > bindings. I think it'd be best to combine both and only highlight where > > > both modes differ. > > > > > > The designware-pcie.txt binding does something similar. > > Ok. I'll merge this into the host mode bindings file and in that differentiate between > > root mode and endpoint mode. > > > > > > > > > diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > > > new file mode 100644 > > > > index 000000000000..4676ccf7dfa5 > > > > --- /dev/null > > > > +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > > > @@ -0,0 +1,138 @@ > > > > +NVIDIA Tegra PCIe Endpoint mode controller (Synopsys DesignWare Core based) > > > > + > > > > +Some of the PCIe controllers which are based on Synopsys DesignWare PCIe IP > > > > +are dual mode i.e. they can work in root port mode or endpoint mode but one > > > > + at a time. Since they are based on DesignWare IP, they inherit all the common > > > > +properties defined in designware-pcie.txt. > > > > + > > > > +Required properties: > > > > +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". > > > > > > The device tree snippets that you added have "nvidia,tegra194-pcie-ep" > > > for EP mode controllers. So either this is wrong or the DTS files are > > > wrong. > > DTS file are correct. This is a mistake in this file. I'll correct this. > > > > > > > > This device tree binding describes the exact same hardware, so I don't > > > think we necessarily need two different compatible strings. It's fairly > > > easy to distinguish between which mode to run in by looking at which > > > properties exist. EP mode for example is the only one that uses the > > > "addr_space" reg entry. > > > > > > Rob, do you know why a different compatible string was chosen for the EP > > > mode? Looking at the driver, there are only a handful of differences in > > > the programming, but most of the driver remains identical. An extra DT > > > compatible string seems a bit exaggerated since it suggests that this is > > > actually different hardware, where it clearly isn't. > > Since all other implementations have done it this way, I just followed to be in sync > > with them. Even I would also like to hear from Rob on the rationale behind this. > > > > > > > > > + Tegra194: Only C0, C4 & C5 controllers are dual mode controllers. > > > > +- power-domains: A phandle to the node that controls power to the respective > > > > + PCIe controller and a specifier name for the PCIe controller. Following are > > > > + the specifiers for the different PCIe controllers > > > > + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 > > > > + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 > > > > + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 > > > > + these specifiers are defined in > > > > + "include/dt-bindings/power/tegra194-powergate.h" file. > > > > +- reg: A list of physical base address and length pairs for each set of > > > > + controller registers. Must contain an entry for each entry in the reg-names > > > > + property. > > > > +- reg-names: Must include the following entries: > > > > + "appl": Controller's application logic registers > > > > + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address > > > > + Translation Unit) registers of the PCIe core are made available > > > > + for SW access. > > > > + "dbi": The aperture where root port's own configuration registers are > > > > + available > > > > + "addr_space": Used to map remote RC address space > > > > +- interrupts: A list of interrupt outputs of the controller. Must contain an > > > > + entry for each entry in the interrupt-names property. > > > > +- interrupt-names: Must include the following entry: > > > > + "intr": The Tegra interrupt that is asserted for controller interrupts > > > > +- clocks: Must contain an entry for each entry in clock-names. > > > > + See ../clocks/clock-bindings.txt for details. > > > > +- clock-names: Must include the following entries: > > > > + - core > > > > +- resets: Must contain an entry for each entry in reset-names. > > > > + See ../reset/reset.txt for details. > > > > +- reset-names: Must include the following entries: > > > > + - apb > > > > + - core > > > > +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. > > > > +- phy-names: Must include an entry for each active lane. > > > > + "p2u-N": where N ranges from 0 to one less than the total number of lanes > > > > +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed > > > > + by controller-id. Following are the controller ids for each controller. > > > > + 0: C0 > > > > + 4: C4 > > > > + 5: C5 > > > > +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals > > > > +- nvidia,pex-rst-gpio: Must contain a phandle to a GPIO controller followed by > > > > + GPIO that is being used as PERST signal > > > > > > Why is this NVIDIA specific? Do other instantiations of the DW IP not > > > also need a means to define which GPIO is the reset? > > I'm not sure. At least I didn't find anything like this in other implementations. > > My understanding is that, controller handles assert/de-assert on the PERST line > > automatically without SW intervention. I think it is for the same reason that other > > implementations don't wait for the REFCLK to flow in from host to configure the IP. > > I think they just use some internal clock for the configuration and switch to > > running the core based on REFCLK as and when it is available > > (i.e. whenever a de-assert is perceived on PERST line by the controller) > > That would be somewhat surprising, though. The IP used in Tegra must be > pretty close to the IP used in other SoCs, and the code that we need in > pex_ep_event_pex_rst_{assert,deassert}() is pretty significant. Why the > other instantiations wouldn't need something similar seems unlikely to > me. > > Perhaps Jingoo or Gustavo can shed some light on this. On my current FPGA prototyping solution, I don't need to control the PERST line and it's very likely that I don't even have access to control it. I guess due to some particularity of my solution, the HW team probably has decided to wire it up directly for some unknown reason to me. However, It seems to me that exynos, imx6, keystone, meson, al, histb, kirin, and qcom drivers controls the PERST line in spite of others driver that doesn't do it like in my prototype solution. In the end I'd says that depends of how the IP solution of design by the HW team. Gustavo > > Thierry > > > > > > > > > > + > > > > +Optional properties: > > > > +- pinctrl-names: A list of pinctrl state names. > > > > + It is mandatory for C5 controller and optional for other controllers. > > > > + - "default": Configures PCIe I/O for proper operation. > > > > +- pinctrl-0: phandle for the 'default' state of pin configuration. > > > > + It is mandatory for C5 controller and optional for other controllers. > > > > +- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt > > > > +- nvidia,update-fc-fixup: This is a boolean property and needs to be present to > > > > + improve performance when a platform is designed in such a way that it > > > > + satisfies at least one of the following conditions thereby enabling root > > > > + port to exchange optimum number of FC (Flow Control) credits with > > > > + downstream devices > > > > + 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS) > > > > + 2. If C0/C4/C5 operate at their respective max link widths and > > > > + a) speed is Gen-2 and MPS is 256B > > > > + b) speed is >= Gen-3 with any MPS > > > > +- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM > > > > + to be specified in microseconds > > > > +- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be > > > > + specified in microseconds > > > > +- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be > > > > + specified in microseconds > > > > + > > > > +NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to > > > > +operate in the endpoint mode because of the way the platform is designed. > > > > +There is a mux that needs to be programmed to let the REFCLK from the host to > > > > +flow into C5 controller when it operates in the endpoint mode. This mux is > > > > +controlled by the GPIO (AA, 5) and it needs to be driven 'high'. For this to > > > > +happen, set status of "pex-refclk-sel-high" node under "gpio@c2f0000" node to > > > > +'okay'. > > > > + When any dual mode controller is made to operate in the endpoint mode, > > > > +please make sure that its respective root port node's status is set to > > > > +'disabled'. > > > > > > This seems very brittle to me. There's no good way how we can detect > > > such misconfigurations. If instead we only have one node describing the > > > hardware fully, the chances of configuring things wrong (by for example > > > enabling both the host and EP mode device tree nodes) can be reduced. > > > > > > So I think instead of duplicating all of the device tree content to have > > > both a host and an EP node for each controller, it'd be better to just > > > have a single node and let the device tree bindings specify which > > > changes to apply to switch into EP mode. > > > > > > For example, there should be nothing wrong with specifying some of the > > > EP-only properties (like num-ib-windows and num-ob-windows) all the time > > > and only use them when we actually run in EP mode. > > > > > > As I mentioned earlier, there are a couple of easy ways to distinguish > > > the modes. The presence of the "addr_space" reg entry is one example, > > > but we could also key off the nvidia,pex-rst-gpio property, since that > > > (presumably) wouldn't be needed for host mode. > > > > > > That way we can just add default, host mode entries to tegra194.dtsi and > > > whenever somebody wants to enable EP mode, they can just override the > > > node in the board-level DTS file, like so: > > > > > > pcie@141a0000 { > > > reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ > > > 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ > > > 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ > > > 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ > > > reg-names = "appl", "atu_dma", "dbi", "addr_space"; > > > > > > nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; > > > }; > > > > > > Thierry > > I like it and fine with making these modifications also but would like to hear from Rob > > also on this. > > > > - Vidya Sagar > > > > > > > + > > > > +Examples: > > > > +========= > > > > + > > > > +Tegra194: > > > > +-------- > > > > + > > > > + pcie_ep@141a0000 { > > > > + compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep"; > > > > + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>; > > > > + reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ > > > > + 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ > > > > + 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ > > > > + 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ > > > > + reg-names = "appl", "atu_dma", "dbi", "addr_space"; > > > > + > > > > + num-lanes = <8>; > > > > + num-ib-windows = <2>; > > > > + num-ob-windows = <8>; > > > > + > > > > + pinctrl-names = "default"; > > > > + pinctrl-0 = <&clkreq_c5_bi_dir_state>; > > > > + > > > > + clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>; > > > > + clock-names = "core"; > > > > + > > > > + resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>, > > > > + <&bpmp TEGRA194_RESET_PEX1_CORE_5>; > > > > + reset-names = "apb", "core"; > > > > + > > > > + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ > > > > + interrupt-names = "intr"; > > > > + > > > > + nvidia,bpmp = <&bpmp 5>; > > > > + > > > > + nvidia,aspm-cmrt-us = <60>; > > > > + nvidia,aspm-pwr-on-t-us = <20>; > > > > + nvidia,aspm-l0s-entrance-latency-us = <3>; > > > > + > > > > + vddio-pex-ctl-supply = <&vdd_1v8ao>; > > > > + > > > > + nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) > > > > + GPIO_ACTIVE_LOW>; > > > > + > > > > + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, > > > > + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, > > > > + <&p2u_nvhs_6>, <&p2u_nvhs_7>; > > > > + > > > > + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", > > > > + "p2u-5", "p2u-6", "p2u-7"; > > > > + }; > > > > -- > > > > 2.17.1 > > > > > >
On 11/25/2019 5:22 PM, Gustavo Pimentel wrote: > On Mon, Nov 25, 2019 at 7:33:59, Thierry Reding > <thierry.reding@gmail.com> wrote: > >> On Mon, Nov 25, 2019 at 12:53:42PM +0530, Vidya Sagar wrote: >>> On 11/22/2019 6:49 PM, Thierry Reding wrote: >>>> On Fri, Nov 22, 2019 at 04:15:01PM +0530, Vidya Sagar wrote: >>>>> Add support for PCIe controllers that can operate in endpoint mode >>>>> in Tegra194. >>>>> >>>>> Signed-off-by: Vidya Sagar <vidyas@nvidia.com> >>>>> --- >>>>> .../bindings/pci/nvidia,tegra194-pcie-ep.txt | 138 ++++++++++++++++++ >>>>> 1 file changed, 138 insertions(+) >>>>> create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt >>>> >>>> The vast majority of this is a duplication of the host mode device tree >>>> bindings. I think it'd be best to combine both and only highlight where >>>> both modes differ. >>>> >>>> The designware-pcie.txt binding does something similar. >>> Ok. I'll merge this into the host mode bindings file and in that differentiate between >>> root mode and endpoint mode. >>> >>>> >>>>> diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt >>>>> new file mode 100644 >>>>> index 000000000000..4676ccf7dfa5 >>>>> --- /dev/null >>>>> +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt >>>>> @@ -0,0 +1,138 @@ >>>>> +NVIDIA Tegra PCIe Endpoint mode controller (Synopsys DesignWare Core based) >>>>> + >>>>> +Some of the PCIe controllers which are based on Synopsys DesignWare PCIe IP >>>>> +are dual mode i.e. they can work in root port mode or endpoint mode but one >>>>> + at a time. Since they are based on DesignWare IP, they inherit all the common >>>>> +properties defined in designware-pcie.txt. >>>>> + >>>>> +Required properties: >>>>> +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". >>>> >>>> The device tree snippets that you added have "nvidia,tegra194-pcie-ep" >>>> for EP mode controllers. So either this is wrong or the DTS files are >>>> wrong. >>> DTS file are correct. This is a mistake in this file. I'll correct this. >>> >>>> >>>> This device tree binding describes the exact same hardware, so I don't >>>> think we necessarily need two different compatible strings. It's fairly >>>> easy to distinguish between which mode to run in by looking at which >>>> properties exist. EP mode for example is the only one that uses the >>>> "addr_space" reg entry. >>>> >>>> Rob, do you know why a different compatible string was chosen for the EP >>>> mode? Looking at the driver, there are only a handful of differences in >>>> the programming, but most of the driver remains identical. An extra DT >>>> compatible string seems a bit exaggerated since it suggests that this is >>>> actually different hardware, where it clearly isn't. >>> Since all other implementations have done it this way, I just followed to be in sync >>> with them. Even I would also like to hear from Rob on the rationale behind this. Rob, Could you please update on this? >>> >>>> >>>>> + Tegra194: Only C0, C4 & C5 controllers are dual mode controllers. >>>>> +- power-domains: A phandle to the node that controls power to the respective >>>>> + PCIe controller and a specifier name for the PCIe controller. Following are >>>>> + the specifiers for the different PCIe controllers >>>>> + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 >>>>> + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 >>>>> + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 >>>>> + these specifiers are defined in >>>>> + "include/dt-bindings/power/tegra194-powergate.h" file. >>>>> +- reg: A list of physical base address and length pairs for each set of >>>>> + controller registers. Must contain an entry for each entry in the reg-names >>>>> + property. >>>>> +- reg-names: Must include the following entries: >>>>> + "appl": Controller's application logic registers >>>>> + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address >>>>> + Translation Unit) registers of the PCIe core are made available >>>>> + for SW access. >>>>> + "dbi": The aperture where root port's own configuration registers are >>>>> + available >>>>> + "addr_space": Used to map remote RC address space >>>>> +- interrupts: A list of interrupt outputs of the controller. Must contain an >>>>> + entry for each entry in the interrupt-names property. >>>>> +- interrupt-names: Must include the following entry: >>>>> + "intr": The Tegra interrupt that is asserted for controller interrupts >>>>> +- clocks: Must contain an entry for each entry in clock-names. >>>>> + See ../clocks/clock-bindings.txt for details. >>>>> +- clock-names: Must include the following entries: >>>>> + - core >>>>> +- resets: Must contain an entry for each entry in reset-names. >>>>> + See ../reset/reset.txt for details. >>>>> +- reset-names: Must include the following entries: >>>>> + - apb >>>>> + - core >>>>> +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. >>>>> +- phy-names: Must include an entry for each active lane. >>>>> + "p2u-N": where N ranges from 0 to one less than the total number of lanes >>>>> +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed >>>>> + by controller-id. Following are the controller ids for each controller. >>>>> + 0: C0 >>>>> + 4: C4 >>>>> + 5: C5 >>>>> +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals >>>>> +- nvidia,pex-rst-gpio: Must contain a phandle to a GPIO controller followed by >>>>> + GPIO that is being used as PERST signal >>>> >>>> Why is this NVIDIA specific? Do other instantiations of the DW IP not >>>> also need a means to define which GPIO is the reset? >>> I'm not sure. At least I didn't find anything like this in other implementations. >>> My understanding is that, controller handles assert/de-assert on the PERST line >>> automatically without SW intervention. I think it is for the same reason that other >>> implementations don't wait for the REFCLK to flow in from host to configure the IP. >>> I think they just use some internal clock for the configuration and switch to >>> running the core based on REFCLK as and when it is available >>> (i.e. whenever a de-assert is perceived on PERST line by the controller) >> >> That would be somewhat surprising, though. The IP used in Tegra must be >> pretty close to the IP used in other SoCs, and the code that we need in >> pex_ep_event_pex_rst_{assert,deassert}() is pretty significant. Why the >> other instantiations wouldn't need something similar seems unlikely to >> me. >> >> Perhaps Jingoo or Gustavo can shed some light on this. > > On my current FPGA prototyping solution, I don't need to control the > PERST line and it's very likely that I don't even have access to control > it. I guess due to some particularity of my solution, the HW team > probably has decided to wire it up directly for some unknown reason to > me. > > However, It seems to me that exynos, imx6, keystone, meson, al, histb, > kirin, and qcom drivers controls the PERST line in spite of others driver > that doesn't do it like in my prototype solution. > In the end I'd says that depends of how the IP solution of design by the > HW team. > > Gustavo > >> >> Thierry >> >>> >>>> >>>>> + >>>>> +Optional properties: >>>>> +- pinctrl-names: A list of pinctrl state names. >>>>> + It is mandatory for C5 controller and optional for other controllers. >>>>> + - "default": Configures PCIe I/O for proper operation. >>>>> +- pinctrl-0: phandle for the 'default' state of pin configuration. >>>>> + It is mandatory for C5 controller and optional for other controllers. >>>>> +- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt >>>>> +- nvidia,update-fc-fixup: This is a boolean property and needs to be present to >>>>> + improve performance when a platform is designed in such a way that it >>>>> + satisfies at least one of the following conditions thereby enabling root >>>>> + port to exchange optimum number of FC (Flow Control) credits with >>>>> + downstream devices >>>>> + 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS) >>>>> + 2. If C0/C4/C5 operate at their respective max link widths and >>>>> + a) speed is Gen-2 and MPS is 256B >>>>> + b) speed is >= Gen-3 with any MPS >>>>> +- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM >>>>> + to be specified in microseconds >>>>> +- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be >>>>> + specified in microseconds >>>>> +- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be >>>>> + specified in microseconds >>>>> + >>>>> +NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to >>>>> +operate in the endpoint mode because of the way the platform is designed. >>>>> +There is a mux that needs to be programmed to let the REFCLK from the host to >>>>> +flow into C5 controller when it operates in the endpoint mode. This mux is >>>>> +controlled by the GPIO (AA, 5) and it needs to be driven 'high'. For this to >>>>> +happen, set status of "pex-refclk-sel-high" node under "gpio@c2f0000" node to >>>>> +'okay'. >>>>> + When any dual mode controller is made to operate in the endpoint mode, >>>>> +please make sure that its respective root port node's status is set to >>>>> +'disabled'. >>>> >>>> This seems very brittle to me. There's no good way how we can detect >>>> such misconfigurations. If instead we only have one node describing the >>>> hardware fully, the chances of configuring things wrong (by for example >>>> enabling both the host and EP mode device tree nodes) can be reduced. >>>> >>>> So I think instead of duplicating all of the device tree content to have >>>> both a host and an EP node for each controller, it'd be better to just >>>> have a single node and let the device tree bindings specify which >>>> changes to apply to switch into EP mode. >>>> >>>> For example, there should be nothing wrong with specifying some of the >>>> EP-only properties (like num-ib-windows and num-ob-windows) all the time >>>> and only use them when we actually run in EP mode. >>>> >>>> As I mentioned earlier, there are a couple of easy ways to distinguish >>>> the modes. The presence of the "addr_space" reg entry is one example, >>>> but we could also key off the nvidia,pex-rst-gpio property, since that >>>> (presumably) wouldn't be needed for host mode. >>>> >>>> That way we can just add default, host mode entries to tegra194.dtsi and >>>> whenever somebody wants to enable EP mode, they can just override the >>>> node in the board-level DTS file, like so: >>>> >>>> pcie@141a0000 { >>>> reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ >>>> 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ >>>> 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ >>>> 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ >>>> reg-names = "appl", "atu_dma", "dbi", "addr_space"; >>>> >>>> nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; >>>> }; >>>> >>>> Thierry >>> I like it and fine with making these modifications also but would like to hear from Rob >>> also on this. >>> >>> - Vidya Sagar >>>> >>>>> + >>>>> +Examples: >>>>> +========= >>>>> + >>>>> +Tegra194: >>>>> +-------- >>>>> + >>>>> + pcie_ep@141a0000 { >>>>> + compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep"; >>>>> + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>; >>>>> + reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ >>>>> + 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ >>>>> + 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ >>>>> + 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ >>>>> + reg-names = "appl", "atu_dma", "dbi", "addr_space"; >>>>> + >>>>> + num-lanes = <8>; >>>>> + num-ib-windows = <2>; >>>>> + num-ob-windows = <8>; >>>>> + >>>>> + pinctrl-names = "default"; >>>>> + pinctrl-0 = <&clkreq_c5_bi_dir_state>; >>>>> + >>>>> + clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>; >>>>> + clock-names = "core"; >>>>> + >>>>> + resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>, >>>>> + <&bpmp TEGRA194_RESET_PEX1_CORE_5>; >>>>> + reset-names = "apb", "core"; >>>>> + >>>>> + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ >>>>> + interrupt-names = "intr"; >>>>> + >>>>> + nvidia,bpmp = <&bpmp 5>; >>>>> + >>>>> + nvidia,aspm-cmrt-us = <60>; >>>>> + nvidia,aspm-pwr-on-t-us = <20>; >>>>> + nvidia,aspm-l0s-entrance-latency-us = <3>; >>>>> + >>>>> + vddio-pex-ctl-supply = <&vdd_1v8ao>; >>>>> + >>>>> + nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) >>>>> + GPIO_ACTIVE_LOW>; >>>>> + >>>>> + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, >>>>> + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, >>>>> + <&p2u_nvhs_6>, <&p2u_nvhs_7>; >>>>> + >>>>> + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", >>>>> + "p2u-5", "p2u-6", "p2u-7"; >>>>> + }; >>>>> -- >>>>> 2.17.1 >>>>> >>> > >
On Fri, Nov 22, 2019 at 02:19:31PM +0100, Thierry Reding wrote: > On Fri, Nov 22, 2019 at 04:15:01PM +0530, Vidya Sagar wrote: > > Add support for PCIe controllers that can operate in endpoint mode > > in Tegra194. > > > > Signed-off-by: Vidya Sagar <vidyas@nvidia.com> > > --- > > .../bindings/pci/nvidia,tegra194-pcie-ep.txt | 138 ++++++++++++++++++ > > 1 file changed, 138 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > The vast majority of this is a duplication of the host mode device tree > bindings. I think it'd be best to combine both and only highlight where > both modes differ. That will not work so well as a schema because all the common PCI bus related properties don't apply. Child nodes if any for an EP aren't PCI devices either. Though you could have 3 files with common properties, host binding and ep bindings. While we don't have anything in terms of common PCI EP bindings, I somewhat expect that to change. There's been something for how to define multiple EP functions for example. > The designware-pcie.txt binding does something similar. > > > diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > new file mode 100644 > > index 000000000000..4676ccf7dfa5 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt > > @@ -0,0 +1,138 @@ > > +NVIDIA Tegra PCIe Endpoint mode controller (Synopsys DesignWare Core based) > > + > > +Some of the PCIe controllers which are based on Synopsys DesignWare PCIe IP > > +are dual mode i.e. they can work in root port mode or endpoint mode but one > > + at a time. Since they are based on DesignWare IP, they inherit all the common > > +properties defined in designware-pcie.txt. > > + > > +Required properties: > > +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". > > The device tree snippets that you added have "nvidia,tegra194-pcie-ep" > for EP mode controllers. So either this is wrong or the DTS files are > wrong. > > This device tree binding describes the exact same hardware, so I don't > think we necessarily need two different compatible strings. It's fairly > easy to distinguish between which mode to run in by looking at which > properties exist. EP mode for example is the only one that uses the > "addr_space" reg entry. > > Rob, do you know why a different compatible string was chosen for the EP > mode? Looking at the driver, there are only a handful of differences in > the programming, but most of the driver remains identical. An extra DT > compatible string seems a bit exaggerated since it suggests that this is > actually different hardware, where it clearly isn't. Whether the driver shares a lot of code or not, it's fundamentally a different device and driver stack. > > + Tegra194: Only C0, C4 & C5 controllers are dual mode controllers. > > +- power-domains: A phandle to the node that controls power to the respective > > + PCIe controller and a specifier name for the PCIe controller. Following are > > + the specifiers for the different PCIe controllers > > + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 > > + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 > > + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 > > + these specifiers are defined in > > + "include/dt-bindings/power/tegra194-powergate.h" file. > > +- reg: A list of physical base address and length pairs for each set of > > + controller registers. Must contain an entry for each entry in the reg-names > > + property. > > +- reg-names: Must include the following entries: > > + "appl": Controller's application logic registers > > + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address > > + Translation Unit) registers of the PCIe core are made available > > + for SW access. > > + "dbi": The aperture where root port's own configuration registers are > > + available > > + "addr_space": Used to map remote RC address space > > +- interrupts: A list of interrupt outputs of the controller. Must contain an > > + entry for each entry in the interrupt-names property. > > +- interrupt-names: Must include the following entry: > > + "intr": The Tegra interrupt that is asserted for controller interrupts > > +- clocks: Must contain an entry for each entry in clock-names. > > + See ../clocks/clock-bindings.txt for details. > > +- clock-names: Must include the following entries: > > + - core > > +- resets: Must contain an entry for each entry in reset-names. > > + See ../reset/reset.txt for details. > > +- reset-names: Must include the following entries: > > + - apb > > + - core > > +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. > > +- phy-names: Must include an entry for each active lane. > > + "p2u-N": where N ranges from 0 to one less than the total number of lanes > > +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed > > + by controller-id. Following are the controller ids for each controller. > > + 0: C0 > > + 4: C4 > > + 5: C5 > > +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals > > +- nvidia,pex-rst-gpio: Must contain a phandle to a GPIO controller followed by > > + GPIO that is being used as PERST signal > > Why is this NVIDIA specific? Do other instantiations of the DW IP not > also need a means to define which GPIO is the reset? 'reset-gpios' is used for PERST. Though in this case it's an input rather than output. Rob
On 11/29/2019 6:56 PM, Vidya Sagar wrote: Rob, Can you please update your comments on this? Thanks, Vidya Sagar > On 11/25/2019 5:22 PM, Gustavo Pimentel wrote: >> On Mon, Nov 25, 2019 at 7:33:59, Thierry Reding >> <thierry.reding@gmail.com> wrote: >> >>> On Mon, Nov 25, 2019 at 12:53:42PM +0530, Vidya Sagar wrote: >>>> On 11/22/2019 6:49 PM, Thierry Reding wrote: >>>>> On Fri, Nov 22, 2019 at 04:15:01PM +0530, Vidya Sagar wrote: >>>>>> Add support for PCIe controllers that can operate in endpoint mode >>>>>> in Tegra194. >>>>>> >>>>>> Signed-off-by: Vidya Sagar <vidyas@nvidia.com> >>>>>> --- >>>>>> .../bindings/pci/nvidia,tegra194-pcie-ep.txt | 138 ++++++++++++++++++ >>>>>> 1 file changed, 138 insertions(+) >>>>>> create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt >>>>> >>>>> The vast majority of this is a duplication of the host mode device tree >>>>> bindings. I think it'd be best to combine both and only highlight where >>>>> both modes differ. >>>>> >>>>> The designware-pcie.txt binding does something similar. >>>> Ok. I'll merge this into the host mode bindings file and in that differentiate between >>>> root mode and endpoint mode. >>>> >>>>> >>>>>> diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt >>>>>> new file mode 100644 >>>>>> index 000000000000..4676ccf7dfa5 >>>>>> --- /dev/null >>>>>> +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt >>>>>> @@ -0,0 +1,138 @@ >>>>>> +NVIDIA Tegra PCIe Endpoint mode controller (Synopsys DesignWare Core based) >>>>>> + >>>>>> +Some of the PCIe controllers which are based on Synopsys DesignWare PCIe IP >>>>>> +are dual mode i.e. they can work in root port mode or endpoint mode but one >>>>>> + at a time. Since they are based on DesignWare IP, they inherit all the common >>>>>> +properties defined in designware-pcie.txt. >>>>>> + >>>>>> +Required properties: >>>>>> +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". >>>>> >>>>> The device tree snippets that you added have "nvidia,tegra194-pcie-ep" >>>>> for EP mode controllers. So either this is wrong or the DTS files are >>>>> wrong. >>>> DTS file are correct. This is a mistake in this file. I'll correct this. >>>> >>>>> >>>>> This device tree binding describes the exact same hardware, so I don't >>>>> think we necessarily need two different compatible strings. It's fairly >>>>> easy to distinguish between which mode to run in by looking at which >>>>> properties exist. EP mode for example is the only one that uses the >>>>> "addr_space" reg entry. >>>>> >>>>> Rob, do you know why a different compatible string was chosen for the EP >>>>> mode? Looking at the driver, there are only a handful of differences in >>>>> the programming, but most of the driver remains identical. An extra DT >>>>> compatible string seems a bit exaggerated since it suggests that this is >>>>> actually different hardware, where it clearly isn't. >>>> Since all other implementations have done it this way, I just followed to be in sync >>>> with them. Even I would also like to hear from Rob on the rationale behind this. > Rob, Could you please update on this? > >>>> >>>>> >>>>>> + Tegra194: Only C0, C4 & C5 controllers are dual mode controllers. >>>>>> +- power-domains: A phandle to the node that controls power to the respective >>>>>> + PCIe controller and a specifier name for the PCIe controller. Following are >>>>>> + the specifiers for the different PCIe controllers >>>>>> + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 >>>>>> + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 >>>>>> + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 >>>>>> + these specifiers are defined in >>>>>> + "include/dt-bindings/power/tegra194-powergate.h" file. >>>>>> +- reg: A list of physical base address and length pairs for each set of >>>>>> + controller registers. Must contain an entry for each entry in the reg-names >>>>>> + property. >>>>>> +- reg-names: Must include the following entries: >>>>>> + "appl": Controller's application logic registers >>>>>> + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address >>>>>> + Translation Unit) registers of the PCIe core are made available >>>>>> + for SW access. >>>>>> + "dbi": The aperture where root port's own configuration registers are >>>>>> + available >>>>>> + "addr_space": Used to map remote RC address space >>>>>> +- interrupts: A list of interrupt outputs of the controller. Must contain an >>>>>> + entry for each entry in the interrupt-names property. >>>>>> +- interrupt-names: Must include the following entry: >>>>>> + "intr": The Tegra interrupt that is asserted for controller interrupts >>>>>> +- clocks: Must contain an entry for each entry in clock-names. >>>>>> + See ../clocks/clock-bindings.txt for details. >>>>>> +- clock-names: Must include the following entries: >>>>>> + - core >>>>>> +- resets: Must contain an entry for each entry in reset-names. >>>>>> + See ../reset/reset.txt for details. >>>>>> +- reset-names: Must include the following entries: >>>>>> + - apb >>>>>> + - core >>>>>> +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. >>>>>> +- phy-names: Must include an entry for each active lane. >>>>>> + "p2u-N": where N ranges from 0 to one less than the total number of lanes >>>>>> +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed >>>>>> + by controller-id. Following are the controller ids for each controller. >>>>>> + 0: C0 >>>>>> + 4: C4 >>>>>> + 5: C5 >>>>>> +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals >>>>>> +- nvidia,pex-rst-gpio: Must contain a phandle to a GPIO controller followed by >>>>>> + GPIO that is being used as PERST signal >>>>> >>>>> Why is this NVIDIA specific? Do other instantiations of the DW IP not >>>>> also need a means to define which GPIO is the reset? >>>> I'm not sure. At least I didn't find anything like this in other implementations. >>>> My understanding is that, controller handles assert/de-assert on the PERST line >>>> automatically without SW intervention. I think it is for the same reason that other >>>> implementations don't wait for the REFCLK to flow in from host to configure the IP. >>>> I think they just use some internal clock for the configuration and switch to >>>> running the core based on REFCLK as and when it is available >>>> (i.e. whenever a de-assert is perceived on PERST line by the controller) >>> >>> That would be somewhat surprising, though. The IP used in Tegra must be >>> pretty close to the IP used in other SoCs, and the code that we need in >>> pex_ep_event_pex_rst_{assert,deassert}() is pretty significant. Why the >>> other instantiations wouldn't need something similar seems unlikely to >>> me. >>> >>> Perhaps Jingoo or Gustavo can shed some light on this. >> >> On my current FPGA prototyping solution, I don't need to control the >> PERST line and it's very likely that I don't even have access to control >> it. I guess due to some particularity of my solution, the HW team >> probably has decided to wire it up directly for some unknown reason to >> me. >> >> However, It seems to me that exynos, imx6, keystone, meson, al, histb, >> kirin, and qcom drivers controls the PERST line in spite of others driver >> that doesn't do it like in my prototype solution. >> In the end I'd says that depends of how the IP solution of design by the >> HW team. >> >> Gustavo >> >>> >>> Thierry >>> >>>> >>>>> >>>>>> + >>>>>> +Optional properties: >>>>>> +- pinctrl-names: A list of pinctrl state names. >>>>>> + It is mandatory for C5 controller and optional for other controllers. >>>>>> + - "default": Configures PCIe I/O for proper operation. >>>>>> +- pinctrl-0: phandle for the 'default' state of pin configuration. >>>>>> + It is mandatory for C5 controller and optional for other controllers. >>>>>> +- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt >>>>>> +- nvidia,update-fc-fixup: This is a boolean property and needs to be present to >>>>>> + improve performance when a platform is designed in such a way that it >>>>>> + satisfies at least one of the following conditions thereby enabling root >>>>>> + port to exchange optimum number of FC (Flow Control) credits with >>>>>> + downstream devices >>>>>> + 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS) >>>>>> + 2. If C0/C4/C5 operate at their respective max link widths and >>>>>> + a) speed is Gen-2 and MPS is 256B >>>>>> + b) speed is >= Gen-3 with any MPS >>>>>> +- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM >>>>>> + to be specified in microseconds >>>>>> +- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be >>>>>> + specified in microseconds >>>>>> +- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be >>>>>> + specified in microseconds >>>>>> + >>>>>> +NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to >>>>>> +operate in the endpoint mode because of the way the platform is designed. >>>>>> +There is a mux that needs to be programmed to let the REFCLK from the host to >>>>>> +flow into C5 controller when it operates in the endpoint mode. This mux is >>>>>> +controlled by the GPIO (AA, 5) and it needs to be driven 'high'. For this to >>>>>> +happen, set status of "pex-refclk-sel-high" node under "gpio@c2f0000" node to >>>>>> +'okay'. >>>>>> + When any dual mode controller is made to operate in the endpoint mode, >>>>>> +please make sure that its respective root port node's status is set to >>>>>> +'disabled'. >>>>> >>>>> This seems very brittle to me. There's no good way how we can detect >>>>> such misconfigurations. If instead we only have one node describing the >>>>> hardware fully, the chances of configuring things wrong (by for example >>>>> enabling both the host and EP mode device tree nodes) can be reduced. >>>>> >>>>> So I think instead of duplicating all of the device tree content to have >>>>> both a host and an EP node for each controller, it'd be better to just >>>>> have a single node and let the device tree bindings specify which >>>>> changes to apply to switch into EP mode. >>>>> >>>>> For example, there should be nothing wrong with specifying some of the >>>>> EP-only properties (like num-ib-windows and num-ob-windows) all the time >>>>> and only use them when we actually run in EP mode. >>>>> >>>>> As I mentioned earlier, there are a couple of easy ways to distinguish >>>>> the modes. The presence of the "addr_space" reg entry is one example, >>>>> but we could also key off the nvidia,pex-rst-gpio property, since that >>>>> (presumably) wouldn't be needed for host mode. >>>>> >>>>> That way we can just add default, host mode entries to tegra194.dtsi and >>>>> whenever somebody wants to enable EP mode, they can just override the >>>>> node in the board-level DTS file, like so: >>>>> >>>>> pcie@141a0000 { >>>>> reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ >>>>> 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ >>>>> 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ >>>>> 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ >>>>> reg-names = "appl", "atu_dma", "dbi", "addr_space"; >>>>> >>>>> nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; >>>>> }; >>>>> >>>>> Thierry >>>> I like it and fine with making these modifications also but would like to hear from Rob >>>> also on this. >>>> >>>> - Vidya Sagar >>>>> >>>>>> + >>>>>> +Examples: >>>>>> +========= >>>>>> + >>>>>> +Tegra194: >>>>>> +-------- >>>>>> + >>>>>> + pcie_ep@141a0000 { >>>>>> + compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep"; >>>>>> + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>; >>>>>> + reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ >>>>>> + 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ >>>>>> + 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ >>>>>> + 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ >>>>>> + reg-names = "appl", "atu_dma", "dbi", "addr_space"; >>>>>> + >>>>>> + num-lanes = <8>; >>>>>> + num-ib-windows = <2>; >>>>>> + num-ob-windows = <8>; >>>>>> + >>>>>> + pinctrl-names = "default"; >>>>>> + pinctrl-0 = <&clkreq_c5_bi_dir_state>; >>>>>> + >>>>>> + clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>; >>>>>> + clock-names = "core"; >>>>>> + >>>>>> + resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>, >>>>>> + <&bpmp TEGRA194_RESET_PEX1_CORE_5>; >>>>>> + reset-names = "apb", "core"; >>>>>> + >>>>>> + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ >>>>>> + interrupt-names = "intr"; >>>>>> + >>>>>> + nvidia,bpmp = <&bpmp 5>; >>>>>> + >>>>>> + nvidia,aspm-cmrt-us = <60>; >>>>>> + nvidia,aspm-pwr-on-t-us = <20>; >>>>>> + nvidia,aspm-l0s-entrance-latency-us = <3>; >>>>>> + >>>>>> + vddio-pex-ctl-supply = <&vdd_1v8ao>; >>>>>> + >>>>>> + nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) >>>>>> + GPIO_ACTIVE_LOW>; >>>>>> + >>>>>> + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, >>>>>> + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, >>>>>> + <&p2u_nvhs_6>, <&p2u_nvhs_7>; >>>>>> + >>>>>> + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", >>>>>> + "p2u-5", "p2u-6", "p2u-7"; >>>>>> + }; >>>>>> -- >>>>>> 2.17.1 >>>>>> >>>> >> >> >
diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt new file mode 100644 index 000000000000..4676ccf7dfa5 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt @@ -0,0 +1,138 @@ +NVIDIA Tegra PCIe Endpoint mode controller (Synopsys DesignWare Core based) + +Some of the PCIe controllers which are based on Synopsys DesignWare PCIe IP +are dual mode i.e. they can work in root port mode or endpoint mode but one + at a time. Since they are based on DesignWare IP, they inherit all the common +properties defined in designware-pcie.txt. + +Required properties: +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". + Tegra194: Only C0, C4 & C5 controllers are dual mode controllers. +- power-domains: A phandle to the node that controls power to the respective + PCIe controller and a specifier name for the PCIe controller. Following are + the specifiers for the different PCIe controllers + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 + these specifiers are defined in + "include/dt-bindings/power/tegra194-powergate.h" file. +- reg: A list of physical base address and length pairs for each set of + controller registers. Must contain an entry for each entry in the reg-names + property. +- reg-names: Must include the following entries: + "appl": Controller's application logic registers + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address + Translation Unit) registers of the PCIe core are made available + for SW access. + "dbi": The aperture where root port's own configuration registers are + available + "addr_space": Used to map remote RC address space +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entry: + "intr": The Tegra interrupt that is asserted for controller interrupts +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - core +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - apb + - core +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. +- phy-names: Must include an entry for each active lane. + "p2u-N": where N ranges from 0 to one less than the total number of lanes +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed + by controller-id. Following are the controller ids for each controller. + 0: C0 + 4: C4 + 5: C5 +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals +- nvidia,pex-rst-gpio: Must contain a phandle to a GPIO controller followed by + GPIO that is being used as PERST signal + +Optional properties: +- pinctrl-names: A list of pinctrl state names. + It is mandatory for C5 controller and optional for other controllers. + - "default": Configures PCIe I/O for proper operation. +- pinctrl-0: phandle for the 'default' state of pin configuration. + It is mandatory for C5 controller and optional for other controllers. +- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt +- nvidia,update-fc-fixup: This is a boolean property and needs to be present to + improve performance when a platform is designed in such a way that it + satisfies at least one of the following conditions thereby enabling root + port to exchange optimum number of FC (Flow Control) credits with + downstream devices + 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS) + 2. If C0/C4/C5 operate at their respective max link widths and + a) speed is Gen-2 and MPS is 256B + b) speed is >= Gen-3 with any MPS +- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM + to be specified in microseconds +- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be + specified in microseconds +- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be + specified in microseconds + +NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to +operate in the endpoint mode because of the way the platform is designed. +There is a mux that needs to be programmed to let the REFCLK from the host to +flow into C5 controller when it operates in the endpoint mode. This mux is +controlled by the GPIO (AA, 5) and it needs to be driven 'high'. For this to +happen, set status of "pex-refclk-sel-high" node under "gpio@c2f0000" node to +'okay'. + When any dual mode controller is made to operate in the endpoint mode, +please make sure that its respective root port node's status is set to +'disabled'. + +Examples: +========= + +Tegra194: +-------- + + pcie_ep@141a0000 { + compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep"; + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>; + reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */ + 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */ + 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */ + 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */ + reg-names = "appl", "atu_dma", "dbi", "addr_space"; + + num-lanes = <8>; + num-ib-windows = <2>; + num-ob-windows = <8>; + + pinctrl-names = "default"; + pinctrl-0 = <&clkreq_c5_bi_dir_state>; + + clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>; + clock-names = "core"; + + resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>, + <&bpmp TEGRA194_RESET_PEX1_CORE_5>; + reset-names = "apb", "core"; + + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ + interrupt-names = "intr"; + + nvidia,bpmp = <&bpmp 5>; + + nvidia,aspm-cmrt-us = <60>; + nvidia,aspm-pwr-on-t-us = <20>; + nvidia,aspm-l0s-entrance-latency-us = <3>; + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + + nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1) + GPIO_ACTIVE_LOW>; + + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, + <&p2u_nvhs_6>, <&p2u_nvhs_7>; + + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", + "p2u-5", "p2u-6", "p2u-7"; + };
Add support for PCIe controllers that can operate in endpoint mode in Tegra194. Signed-off-by: Vidya Sagar <vidyas@nvidia.com> --- .../bindings/pci/nvidia,tegra194-pcie-ep.txt | 138 ++++++++++++++++++ 1 file changed, 138 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie-ep.txt