[v4,2/2] dt-bindings: iio: Add ltc2983 documentation

Document the LTC2983 temperature sensor devicetree bindings.

Signed-off-by: Nuno Sá <nuno.sa@analog.com>
---
Changes in v2:
 * Drop maxItems in non-array elements;
 * Set adi,mux-delay-config-us instead of adi,mux-delay-config;
 * Wrapped lines at 80 char;
 * Added comas to enum elements;
 * Use real units in adi,excitation-current;
 * Moved some enums to minimum and maximum;
 * Grouped patternProperties and moved reg property as a generic property.

Changes in v3:
 * Add meaning to adi,sensor-type values which are not const;
 * Add meaning to adi,filter-notch-freq values;
 * Break up adi,sensor-config into human readable elements;
 * Set maxItems/minItems at the same identation as allOf in adi,custom-sensor;
 * Fixed the maximum value for adi,sensor-type for sensors with custom support;
 * Changed license to GPL-2.0-only as it should be for new bindings;
 * Changed spi0 to spi in the dts example;
 * Updated the dts example to the new properties.

Changes in v4:
 * Set correct license for new bindings;
 * Drop $ref for standard unit suffixes;
 * Dropped adi,temperature-celcius;
 * Drop '.*' in the patternProperties regex;
 * Make min/man a single schema;
 * Have rsense in milli ohms;
 * Dropped '|' when no formatting is needed;
 * Add matrixes for adi,custom-sensors;
 * Rename adi,custom-sensor to a more appropriate and distinct name;
 * Add adi,custom-stenheirt for thermistors.

 .../bindings/iio/temperature/adi,ltc2983.yaml | 478 ++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 479 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml

On Fri, 11 Oct 2019 10:40:38 +0200
Nuno Sá <nuno.sa@analog.com> wrote:

> Document the LTC2983 temperature sensor devicetree bindings.
> 
> Signed-off-by: Nuno Sá <nuno.sa@analog.com>

I'm happy with this, but will be waiting for Rob to have a chance
for a final look before applying.

Thanks,

Jonathan

> ---
> Changes in v2:
>  * Drop maxItems in non-array elements;
>  * Set adi,mux-delay-config-us instead of adi,mux-delay-config;
>  * Wrapped lines at 80 char;
>  * Added comas to enum elements;
>  * Use real units in adi,excitation-current;
>  * Moved some enums to minimum and maximum;
>  * Grouped patternProperties and moved reg property as a generic property.
> 
> Changes in v3:
>  * Add meaning to adi,sensor-type values which are not const;
>  * Add meaning to adi,filter-notch-freq values;
>  * Break up adi,sensor-config into human readable elements;
>  * Set maxItems/minItems at the same identation as allOf in adi,custom-sensor;
>  * Fixed the maximum value for adi,sensor-type for sensors with custom support;
>  * Changed license to GPL-2.0-only as it should be for new bindings;
>  * Changed spi0 to spi in the dts example;
>  * Updated the dts example to the new properties.
> 
> Changes in v4:
>  * Set correct license for new bindings;
>  * Drop $ref for standard unit suffixes;
>  * Dropped adi,temperature-celcius;
>  * Drop '.*' in the patternProperties regex;
>  * Make min/man a single schema;
>  * Have rsense in milli ohms;
>  * Dropped '|' when no formatting is needed;
>  * Add matrixes for adi,custom-sensors;
>  * Rename adi,custom-sensor to a more appropriate and distinct name;
>  * Add adi,custom-stenheirt for thermistors.
> 
>  .../bindings/iio/temperature/adi,ltc2983.yaml | 478 ++++++++++++++++++
>  MAINTAINERS                                   |   1 +
>  2 files changed, 479 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml b/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml
> new file mode 100644
> index 000000000000..b4946c6530c0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml
> @@ -0,0 +1,478 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/temperature/adi,ltc2983.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices LTC2983 Multi-sensor Temperature system
> +
> +maintainers:
> +  - Nuno Sá <nuno.sa@analog.com>
> +
> +description: |
> +  Analog Devices LTC2983 Multi-Sensor Digital Temperature Measurement System
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/2983fc.pdf
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,ltc2983
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  adi,mux-delay-config-us:
> +    description:
> +      The LTC2983 performs 2 or 3 internal conversion cycles per temperature
> +      result. Each conversion cycle is performed with different excitation and
> +      input multiplexer configurations. Prior to each conversion, these
> +      excitation circuits and input switch configurations are changed and an
> +      internal 1ms delay ensures settling prior to the conversion cycle in most
> +      cases. An extra delay can be configured using this property. The value is
> +      rounded to nearest 100us.
> +    maximum: 255
> +
> +  adi,filter-notch-freq:
> +    description:
> +      Set's the default setting of the digital filter. The default is
> +      simultaneous 50/60Hz rejection.
> +      0 - 50/60Hz rejection
> +      1 - 60Hz rejection
> +      2 - 50Hz rejection
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - minimum: 0
> +        maximum: 2
> +
> +  '#address-cells':
> +    const: 1
> +
> +  '#size-cells':
> +    const: 0
> +
> +patternProperties:
> +  "@([1-9]|1[0-9]|20)$":
> +    type: object
> +
> +    properties:
> +      reg:
> +        description:
> +          The channel number. It can be connected to one of the 20 channels of
> +          the device.
> +        minimum: 1
> +        maximum: 20
> +
> +      adi,sensor-type:
> +        description: Identifies the type of sensor connected to the device.
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +
> +    required:
> +      - reg
> +      - adi,sensor-type
> +
> +  "^thermocouple@":
> +    type: object
> +    description:
> +      Represents a thermocouple sensor which is connected to one of the device
> +      channels.
> +
> +    properties:
> +      adi,sensor-type:
> +        description: |
> +          1 - Type J Thermocouple
> +          2 - Type K Thermocouple
> +          3 - Type E Thermocouple
> +          4 - Type N Thermocouple
> +          5 - Type R Thermocouple
> +          6 - Type S Thermocouple
> +          7 - Type T Thermocouple
> +          8 - Type B Thermocouple
> +          9 - Custom Thermocouple
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +        minimum: 1
> +        maximum: 9
> +
> +      adi,single-ended:
> +        description:
> +          Boolean property which set's the thermocouple as single-ended.
> +        type: boolean
> +
> +      adi,sensor-oc-current-microamp:
> +        description:
> +          This property set's the pulsed current value applied during
> +          open-circuit detect.
> +        enum: [10, 100, 500, 1000]
> +
> +      adi,cold-junction-handle:
> +        description:
> +          Phandle which points to a sensor object responsible for measuring
> +          the thermocouple cold junction temperature.
> +        $ref: "/schemas/types.yaml#/definitions/phandle"
> +
> +      adi,custom-thermocouple:
> +        description:
> +          This is a table, where each entry should be a pair of
> +          voltage(mv)-temperature(K). The entries must be given in nv and uK
> +          so that, the original values must be multiplied by 1000000. For
> +          more details look at table 69 and 70.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/int64-matrix
> +        items:
> +          minItems: 3
> +          maxItems: 64
> +          items:
> +            minItems: 2
> +            maxItems: 2
> +
> +  "^diode@":
> +    type: object
> +    description:
> +      Represents a diode sensor which is connected to one of the device
> +      channels.
> +
> +    properties:
> +      adi,sensor-type:
> +        description: Identifies the sensor as a diode.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +        const: 28
> +
> +      adi,single-ended:
> +        description: Boolean property which set's the diode as single-ended.
> +        type: boolean
> +
> +      adi,three-conversion-cycles:
> +        description:
> +          Boolean property which set's three conversion cycles removing
> +          parasitic resistance effects between the LTC2983 and the diode.
> +        type: boolean
> +
> +      adi,average-on:
> +        description:
> +          Boolean property which enables a running average of the diode
> +          temperature reading. This reduces the noise when the diode is used
> +          as a cold junction temperature element on an isothermal block
> +          where temperatures change slowly.
> +        type: boolean
> +
> +      adi,excitation-current-microamp:
> +        description:
> +          This property controls the magnitude of the excitation current
> +          applied to the diode. Depending on the number of conversions
> +          cycles, this property will assume different predefined values on
> +          each cycle. Just set the value of the first cycle (1l).
> +        enum: [10, 20, 40, 80]
> +
> +      adi,ideal-factor-value:
> +        description:
> +          This property sets the diode ideality factor. The real value must
> +          be multiplied by 1000000 to remove the fractional part. For more
> +          information look at table 20 of the datasheet.
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  "^rtd@":
> +    type: object
> +    description:
> +      Represents a rtd sensor which is connected to one of the device channels.
> +
> +    properties:
> +      reg:
> +        minimum: 2
> +        maximum: 20
> +
> +      adi,sensor-type:
> +        description: |
> +          10 - RTD PT-10
> +          11 - RTD PT-50
> +          12 - RTD PT-100
> +          13 - RTD PT-200
> +          14 - RTD PT-500
> +          15 - RTD PT-1000
> +          16 - RTD PT-1000 (0.00375)
> +          17 - RTD NI-120
> +          18 - RTD Custom
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +        minimum: 10
> +        maximum: 18
> +
> +      adi,rsense-handle:
> +        description:
> +          Phandle pointing to a rsense object associated with this RTD.
> +        $ref: "/schemas/types.yaml#/definitions/phandle"
> +
> +      adi,number-of-wires:
> +        description:
> +          Identifies the number of wires used by the RTD. Setting this
> +          property to 5 means 4 wires with Kelvin Rsense.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +          - enum: [2, 3, 4, 5]
> +
> +      adi,rsense-share:
> +        description:
> +          Boolean property which enables Rsense sharing, where one sense
> +          resistor is used for multiple 2-, 3-, and/or 4-wire RTDs.
> +        type: boolean
> +
> +      adi,current-rotate:
> +        description:
> +          Boolean property which enables excitation current rotation to
> +          automatically remove parasitic thermocouple effects. Note that
> +          this property is not allowed for 2- and 3-wire RTDs.
> +        type: boolean
> +
> +      adi,excitation-current-microamp:
> +        description:
> +          This property controls the magnitude of the excitation current
> +          applied to the RTD.
> +        enum: [5, 10, 25, 50, 100, 250, 500, 1000]
> +
> +      adi,rtd-curve:
> +        description:
> +          This property set the RTD curve used and the corresponding
> +          Callendar-VanDusen constants. Look at table 30 of the datasheet.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +          - minimum: 0
> +            maximum: 3
> +
> +      adi,custom-rtd:
> +        description:
> +          This is a table, where each entry should be a pair of
> +          resistance(ohm)-temperature(K). The entries added here are in uohm
> +          and uK. For more details values look at table 74 and 75.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint64-matrix
> +        items:
> +          minItems: 3
> +          maxItems: 64
> +          items:
> +            minItems: 2
> +            maxItems: 2
> +
> +    required:
> +      - adi,rsense-handle
> +
> +    dependencies:
> +      adi,current-rotate: [ adi,rsense-share ]
> +
> +  "^thermistor@":
> +    type: object
> +    description:
> +      Represents a thermistor sensor which is connected to one of the device
> +      channels.
> +
> +    properties:
> +      adi,sensor-type:
> +        description:
> +          19 - Thermistor 44004/44033 2.252kohm at 25°C
> +          20 - Thermistor 44005/44030 3kohm at 25°C
> +          21 - Thermistor 44007/44034 5kohm at 25°C
> +          22 - Thermistor 44006/44031 10kohm at 25°C
> +          23 - Thermistor 44008/44032 30kohm at 25°C
> +          24 - Thermistor YSI 400 2.252kohm at 25°C
> +          25 - Thermistor Spectrum 1003k 1kohm
> +          26 - Thermistor Custom Steinhart-Hart
> +          27 - Custom Thermistor
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +        minimum: 19
> +        maximum: 27
> +
> +      adi,rsense-handle:
> +        description:
> +          Phandle pointing to a rsense object associated with this
> +          thermistor.
> +        $ref: "/schemas/types.yaml#/definitions/phandle"
> +
> +      adi,single-ended:
> +        description:
> +          Boolean property which set's the thermistor as single-ended.
> +        type: boolean
> +
> +      adi,rsense-share:
> +        description:
> +          Boolean property which enables Rsense sharing, where one sense
> +          resistor is used for multiple thermistors. Note that this property
> +          is ignored if adi,single-ended is set.
> +        type: boolean
> +
> +      adi,current-rotate:
> +        description:
> +          Boolean property which enables excitation current rotation to
> +          automatically remove parasitic thermocouple effects.
> +        type: boolean
> +
> +      adi,excitation-current-nanoamp:
> +        description:
> +          This property controls the magnitude of the excitation current
> +          applied to the thermistor. Value 0 set's the sensor in auto-range
> +          mode.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +          - enum: [0, 250, 500, 1000, 5000, 10000, 25000, 50000, 100000,
> +                   250000, 500000, 1000000]
> +
> +      adi,custom-thermistor:
> +        description:
> +          This is a table, where each entry should be a pair of
> +          resistance(ohm)-temperature(K). The entries added here are in uohm
> +          and uK only for custom thermistors. For more details look at table
> +          78 and 79.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint64-matrix
> +        items:
> +          minItems: 3
> +          maxItems: 64
> +          items:
> +            minItems: 2
> +            maxItems: 2
> +
> +      adi,custom-steinhart:
> +        description:
> +          Steinhart-Hart coefficients are also supported and can
> +          be programmed into the device memory using this property. For
> +          Steinhart sensors the coefficients are given in the raw
> +          format. Look at table 82 for more information.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32-array
> +        items:
> +          minItems: 6
> +          maxItems: 6
> +
> +    required:
> +      - adi,rsense-handle
> +
> +    dependencies:
> +      adi,current-rotate: [ adi,rsense-share ]
> +
> +  "^adc@":
> +    type: object
> +    description: Represents a channel which is being used as a direct adc.
> +
> +    properties:
> +      adi,sensor-type:
> +        description: Identifies the sensor as a direct adc.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +        const: 30
> +
> +      adi,single-ended:
> +        description: Boolean property which set's the adc as single-ended.
> +        type: boolean
> +
> +  "^rsense@":
> +    type: object
> +    description:
> +      Represents a rsense which is connected to one of the device channels.
> +      Rsense are used by thermistors and RTD's.
> +
> +    properties:
> +      reg:
> +        minimum: 2
> +        maximum: 20
> +
> +      adi,sensor-type:
> +        description: Identifies the sensor as a rsense.
> +        allOf:
> +          - $ref: /schemas/types.yaml#/definitions/uint32
> +        const: 29
> +
> +      adi,rsense-val-milli-ohms:
> +        description:
> +          Sets the value of the sense resistor. Look at table 20 of the
> +          datasheet for information.
> +
> +    required:
> +      - adi,rsense-val-milli-ohms
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    spi {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        sensor_ltc2983: ltc2983@0 {
> +                compatible = "adi,ltc2983";
> +                reg = <0>;
> +
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                interrupts = <20 IRQ_TYPE_EDGE_RISING>;
> +                interrupt-parent = <&gpio>;
> +
> +                thermocouple@18 {
> +                        reg = <18>;
> +                        adi,sensor-type = <8>; //Type B
> +                        adi,sensor-oc-current-microamp = <10>;
> +                        adi,cold-junction-handle = <&diode5>;
> +                };
> +
> +                diode5: diode@5 {
> +                        reg = <5>;
> +                        adi,sensor-type = <28>;
> +                };
> +
> +                rsense2: rsense@2 {
> +                        reg = <2>;
> +                        adi,sensor-type = <29>;
> +                        adi,rsense-val-milli-ohms = <1200000>; //1.2Kohms
> +                };
> +
> +                rtd@14 {
> +                        reg = <14>;
> +                        adi,sensor-type = <15>; //PT1000
> +                        /*2-wire, internal gnd, no current rotation*/
> +                        adi,number-of-wires = <2>;
> +                        adi,rsense-share;
> +                        adi,excitation-current-microamp = <500>;
> +                        adi,rsense-handle = <&rsense2>;
> +                };
> +
> +                adc@10 {
> +                        reg = <10>;
> +                        adi,sensor-type = <30>;
> +                        adi,single-ended;
> +                };
> +
> +                thermistor@12 {
> +                        reg = <12>;
> +                        adi,sensor-type = <26>; //Steinhart
> +                        adi,rsense-handle = <&rsense2>;
> +                        adi,custom-steinhart = <0x00F371EC 0x12345678
> +                                        0x2C0F8733 0x10018C66 0xA0FEACCD
> +                                        0x90021D99>; //6 entries
> +                };
> +
> +                thermocouple@20 {
> +                        reg = <20>;
> +                        adi,sensor-type = <9>; //custom thermocouple
> +                        adi,single-ended;
> +                        adi,custom-thermocouple = /bits/ 64
> +                                 <(-50220000) 0
> +                                  (-30200000) 99100000
> +                                  (-5300000) 135400000
> +                                  0 273150000
> +                                  40200000 361200000
> +                                  55300000 522100000
> +                                  88300000 720300000
> +                                  132200000 811200000
> +                                  188700000 922500000
> +                                  460400000 1000000000>; //10 pairs
> +               };
> +
> +        };
> +    };
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 14a256e785ca..f747a9dc27f5 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -9497,6 +9497,7 @@ W:	http://ez.analog.com/community/linux-device-drivers
>  L:	linux-iio@vger.kernel.org
>  S:	Supported
>  F:	drivers/iio/temperature/ltc2983.c
> +F:	Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml
>  
>  LTC4261 HARDWARE MONITOR DRIVER
>  M:	Guenter Roeck <linux@roeck-us.net>

On Sat, Oct 12, 2019 at 11:57:45AM +0100, Jonathan Cameron wrote:
> On Fri, 11 Oct 2019 10:40:38 +0200
> Nuno Sá <nuno.sa@analog.com> wrote:
> 
> > Document the LTC2983 temperature sensor devicetree bindings.
> > 
> > Signed-off-by: Nuno Sá <nuno.sa@analog.com>
> 
> I'm happy with this, but will be waiting for Rob to have a chance
> for a final look before applying.

LGTM, but I need to add the int64-matrix type to the core schema first 
or this will give you errors. I should get to that in the next day or 
so.

Rob

On Mon, Oct 14, 2019 at 9:39 AM Rob Herring <robh@kernel.org> wrote:
>
> On Sat, Oct 12, 2019 at 11:57:45AM +0100, Jonathan Cameron wrote:
> > On Fri, 11 Oct 2019 10:40:38 +0200
> > Nuno Sá <nuno.sa@analog.com> wrote:
> >
> > > Document the LTC2983 temperature sensor devicetree bindings.
> > >
> > > Signed-off-by: Nuno Sá <nuno.sa@analog.com>
> >
> > I'm happy with this, but will be waiting for Rob to have a chance
> > for a final look before applying.
>
> LGTM, but I need to add the int64-matrix type to the core schema first
> or this will give you errors. I should get to that in the next day or
> so.

Now added, so please update dtschema and check.

Reviewed-by: Rob Herring <robh@kernel.org>

On Tue, 15 Oct 2019 09:19:10 -0500
Rob Herring <robh@kernel.org> wrote:

> On Mon, Oct 14, 2019 at 9:39 AM Rob Herring <robh@kernel.org> wrote:
> >
> > On Sat, Oct 12, 2019 at 11:57:45AM +0100, Jonathan Cameron wrote:  
> > > On Fri, 11 Oct 2019 10:40:38 +0200
> > > Nuno Sá <nuno.sa@analog.com> wrote:
> > >  
> > > > Document the LTC2983 temperature sensor devicetree bindings.
> > > >
> > > > Signed-off-by: Nuno Sá <nuno.sa@analog.com>  
> > >
> > > I'm happy with this, but will be waiting for Rob to have a chance
> > > for a final look before applying.  
> >
> > LGTM, but I need to add the int64-matrix type to the core schema first
> > or this will give you errors. I should get to that in the next day or
> > so.  
> 
> Now added, so please update dtschema and check.
> 
> Reviewed-by: Rob Herring <robh@kernel.org>

/home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:0: 18446744073659331616 is greater than the maximum of 9223372036854775807
/home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:2: 18446744073679351616 is greater than the maximum of 9223372036854775807
/home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:4: 18446744073704251616 is greater than the maximum of 9223372036854775807

Which is odd.  I haven't looked into it beyond testing and reverting the
patch as out of time for today.

Thanks,

Jonathan

On Tue, 15 Oct 2019 21:44:35 +0100
Jonathan Cameron <jic23@kernel.org> wrote:

> On Tue, 15 Oct 2019 09:19:10 -0500
> Rob Herring <robh@kernel.org> wrote:
> 
> > On Mon, Oct 14, 2019 at 9:39 AM Rob Herring <robh@kernel.org> wrote:  
> > >
> > > On Sat, Oct 12, 2019 at 11:57:45AM +0100, Jonathan Cameron wrote:    
> > > > On Fri, 11 Oct 2019 10:40:38 +0200
> > > > Nuno Sá <nuno.sa@analog.com> wrote:
> > > >    
> > > > > Document the LTC2983 temperature sensor devicetree bindings.
> > > > >
> > > > > Signed-off-by: Nuno Sá <nuno.sa@analog.com>    
> > > >
> > > > I'm happy with this, but will be waiting for Rob to have a chance
> > > > for a final look before applying.    
> > >
> > > LGTM, but I need to add the int64-matrix type to the core schema first
> > > or this will give you errors. I should get to that in the next day or
> > > so.    
> > 
> > Now added, so please update dtschema and check.
> > 
> > Reviewed-by: Rob Herring <robh@kernel.org>  
> 
> /home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:0: 18446744073659331616 is greater than the maximum of 9223372036854775807
> /home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:2: 18446744073679351616 is greater than the maximum of 9223372036854775807
> /home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:4: 18446744073704251616 is greater than the maximum of 9223372036854775807
> 
> Which is odd.  I haven't looked into it beyond testing and reverting the
> patch as out of time for today.

I'm still getting this and not sure why.  Rob?

Thanks,

Jonathan

> 
> Thanks,
> 
> Jonathan
> 
>

On Mon, Oct 21, 2019 at 10:27 AM Jonathan Cameron <jic23@kernel.org> wrote:
>
> On Tue, 15 Oct 2019 21:44:35 +0100
> Jonathan Cameron <jic23@kernel.org> wrote:
>
> > On Tue, 15 Oct 2019 09:19:10 -0500
> > Rob Herring <robh@kernel.org> wrote:
> >
> > > On Mon, Oct 14, 2019 at 9:39 AM Rob Herring <robh@kernel.org> wrote:
> > > >
> > > > On Sat, Oct 12, 2019 at 11:57:45AM +0100, Jonathan Cameron wrote:
> > > > > On Fri, 11 Oct 2019 10:40:38 +0200
> > > > > Nuno Sá <nuno.sa@analog.com> wrote:
> > > > >
> > > > > > Document the LTC2983 temperature sensor devicetree bindings.
> > > > > >
> > > > > > Signed-off-by: Nuno Sá <nuno.sa@analog.com>
> > > > >
> > > > > I'm happy with this, but will be waiting for Rob to have a chance
> > > > > for a final look before applying.
> > > >
> > > > LGTM, but I need to add the int64-matrix type to the core schema first
> > > > or this will give you errors. I should get to that in the next day or
> > > > so.
> > >
> > > Now added, so please update dtschema and check.
> > >
> > > Reviewed-by: Rob Herring <robh@kernel.org>
> >
> > /home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:0: 18446744073659331616 is greater than the maximum of 9223372036854775807
> > /home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:2: 18446744073679351616 is greater than the maximum of 9223372036854775807
> > /home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:4: 18446744073704251616 is greater than the maximum of 9223372036854775807
> >
> > Which is odd.  I haven't looked into it beyond testing and reverting the
> > patch as out of time for today.
>
> I'm still getting this and not sure why.  Rob?

Just realized I failed to send my draft...

This is dtc yaml output not maintaining the sign, so everything is
unsigned. (I had mentioned this and then promptly forgot.) I'll need
to figure out how to plumb this thru dtc. For now, its probably
easiest to just change to uint64-matrix with a comment that it should
be signed.

Rob

On Mon, 21 Oct 2019 12:21:41 -0500
Rob Herring <robh@kernel.org> wrote:

> On Mon, Oct 21, 2019 at 10:27 AM Jonathan Cameron <jic23@kernel.org> wrote:
> >
> > On Tue, 15 Oct 2019 21:44:35 +0100
> > Jonathan Cameron <jic23@kernel.org> wrote:
> >  
> > > On Tue, 15 Oct 2019 09:19:10 -0500
> > > Rob Herring <robh@kernel.org> wrote:
> > >  
> > > > On Mon, Oct 14, 2019 at 9:39 AM Rob Herring <robh@kernel.org> wrote:  
> > > > >
> > > > > On Sat, Oct 12, 2019 at 11:57:45AM +0100, Jonathan Cameron wrote:  
> > > > > > On Fri, 11 Oct 2019 10:40:38 +0200
> > > > > > Nuno Sá <nuno.sa@analog.com> wrote:
> > > > > >  
> > > > > > > Document the LTC2983 temperature sensor devicetree bindings.
> > > > > > >
> > > > > > > Signed-off-by: Nuno Sá <nuno.sa@analog.com>  
> > > > > >
> > > > > > I'm happy with this, but will be waiting for Rob to have a chance
> > > > > > for a final look before applying.  
> > > > >
> > > > > LGTM, but I need to add the int64-matrix type to the core schema first
> > > > > or this will give you errors. I should get to that in the next day or
> > > > > so.  
> > > >
> > > > Now added, so please update dtschema and check.
> > > >
> > > > Reviewed-by: Rob Herring <robh@kernel.org>  
> > >
> > > /home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:0: 18446744073659331616 is greater than the maximum of 9223372036854775807
> > > /home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:2: 18446744073679351616 is greater than the maximum of 9223372036854775807
> > > /home/jic23/src/kernel/iio/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.example.dt.yaml: ltc2983@0: thermocouple@20:adi,custom-thermocouple:0:4: 18446744073704251616 is greater than the maximum of 9223372036854775807
> > >
> > > Which is odd.  I haven't looked into it beyond testing and reverting the
> > > patch as out of time for today.  
> >
> > I'm still getting this and not sure why.  Rob?  
> 
> Just realized I failed to send my draft...
> 
> This is dtc yaml output not maintaining the sign, so everything is
> unsigned. (I had mentioned this and then promptly forgot.) I'll need
> to figure out how to plumb this thru dtc. For now, its probably
> easiest to just change to uint64-matrix with a comment that it should
> be signed.
> 
> Rob
Thanks.  Made the change and added the note to the docs.

Applied to the togreg branch of iio.git and pushed out as testing for
the autobuilders to play with it.

Thanks,

Jonathan