@@ -42,8 +42,8 @@ fi
[ -z "$BURST" ] && BURST=1024
[ -z "$COUNT" ] && COUNT="10000000" # Zero means indefinitely
if [ -n "$DST_PORT" ]; then
- read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT)
- validate_ports $DST_MIN $DST_MAX
+ read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT)
+ validate_ports $UDP_DST_MIN $UDP_DST_MAX
fi
# Base Config
@@ -76,8 +76,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do
if [ -n "$DST_PORT" ]; then
# Single destination port or random port range
pg_set $dev "flag UDPDST_RND"
- pg_set $dev "udp_dst_min $DST_MIN"
- pg_set $dev "udp_dst_max $DST_MAX"
+ pg_set $dev "udp_dst_min $UDP_DST_MIN"
+ pg_set $dev "udp_dst_max $UDP_DST_MAX"
fi
# Inject packet into RX path of stack
@@ -25,8 +25,8 @@ if [[ -n "$BURST" ]]; then
fi
[ -z "$COUNT" ] && COUNT="10000000" # Zero means indefinitely
if [ -n "$DST_PORT" ]; then
- read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT)
- validate_ports $DST_MIN $DST_MAX
+ read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT)
+ validate_ports $UDP_DST_MIN $UDP_DST_MAX
fi
# Base Config
@@ -59,8 +59,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do
if [ -n "$DST_PORT" ]; then
# Single destination port or random port range
pg_set $dev "flag UDPDST_RND"
- pg_set $dev "udp_dst_min $DST_MIN"
- pg_set $dev "udp_dst_max $DST_MAX"
+ pg_set $dev "udp_dst_min $UDP_DST_MIN"
+ pg_set $dev "udp_dst_max $UDP_DST_MAX"
fi
# Inject packet into TX qdisc egress path of stack
@@ -23,16 +23,16 @@ fi
[ -z "$DST_MAC" ] && usage && err 2 "Must specify -m dst_mac"
[ -z "$COUNT" ] && COUNT="100000" # Zero means indefinitely
if [ -n "$DST_PORT" ]; then
- read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT)
- validate_ports $DST_MIN $DST_MAX
+ read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT)
+ validate_ports $UDP_DST_MIN $UDP_DST_MAX
fi
# Base Config
DELAY="0" # Zero means max speed
# Flow variation random source port between min and max
-UDP_MIN=9
-UDP_MAX=109
+UDP_SRC_MIN=9
+UDP_SRC_MAX=109
# General cleanup everything since last run
# (especially important if other threads were configured by other scripts)
@@ -66,14 +66,14 @@ pg_set $DEV "dst$IP6 $DEST_IP"
if [ -n "$DST_PORT" ]; then
# Single destination port or random port range
pg_set $DEV "flag UDPDST_RND"
- pg_set $DEV "udp_dst_min $DST_MIN"
- pg_set $DEV "udp_dst_max $DST_MAX"
+ pg_set $DEV "udp_dst_min $UDP_DST_MIN"
+ pg_set $DEV "udp_dst_max $UDP_DST_MAX"
fi
# Setup random UDP port src range
pg_set $DEV "flag UDPSRC_RND"
-pg_set $DEV "udp_src_min $UDP_MIN"
-pg_set $DEV "udp_src_max $UDP_MAX"
+pg_set $DEV "udp_src_min $UDP_SRC_MIN"
+pg_set $DEV "udp_src_max $UDP_SRC_MAX"
# start_run
echo "Running... ctrl^C to stop" >&2
@@ -21,8 +21,8 @@ DELAY="0" # Zero means max speed
[ -z "$CLONE_SKB" ] && CLONE_SKB="0"
# Flow variation random source port between min and max
-UDP_MIN=9
-UDP_MAX=109
+UDP_SRC_MIN=9
+UDP_SRC_MAX=109
# (example of setting default params in your script)
if [ -z "$DEST_IP" ]; then
@@ -30,8 +30,8 @@ if [ -z "$DEST_IP" ]; then
fi
[ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff"
if [ -n "$DST_PORT" ]; then
- read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT)
- validate_ports $DST_MIN $DST_MAX
+ read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT)
+ validate_ports $UDP_DST_MIN $UDP_DST_MAX
fi
# General cleanup everything since last run
@@ -67,14 +67,14 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do
if [ -n "$DST_PORT" ]; then
# Single destination port or random port range
pg_set $dev "flag UDPDST_RND"
- pg_set $dev "udp_dst_min $DST_MIN"
- pg_set $dev "udp_dst_max $DST_MAX"
+ pg_set $dev "udp_dst_min $UDP_DST_MIN"
+ pg_set $dev "udp_dst_max $UDP_DST_MAX"
fi
# Setup random UDP port src range
pg_set $dev "flag UDPSRC_RND"
- pg_set $dev "udp_src_min $UDP_MIN"
- pg_set $dev "udp_src_max $UDP_MAX"
+ pg_set $dev "udp_src_min $UDP_SRC_MIN"
+ pg_set $dev "udp_src_max $UDP_SRC_MAX"
done
# start_run
@@ -34,8 +34,8 @@ fi
[ -z "$CLONE_SKB" ] && CLONE_SKB="0" # No need for clones when bursting
[ -z "$COUNT" ] && COUNT="0" # Zero means indefinitely
if [ -n "$DST_PORT" ]; then
- read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT)
- validate_ports $DST_MIN $DST_MAX
+ read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT)
+ validate_ports $UDP_DST_MIN $UDP_DST_MAX
fi
# Base Config
@@ -67,8 +67,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do
if [ -n "$DST_PORT" ]; then
# Single destination port or random port range
pg_set $dev "flag UDPDST_RND"
- pg_set $dev "udp_dst_min $DST_MIN"
- pg_set $dev "udp_dst_max $DST_MAX"
+ pg_set $dev "udp_dst_min $UDP_DST_MIN"
+ pg_set $dev "udp_dst_max $UDP_DST_MAX"
fi
# Setup burst, for easy testing -b 0 disable bursting
@@ -18,8 +18,8 @@ source ${basedir}/parameters.sh
[ -z "$CLONE_SKB" ] && CLONE_SKB="0"
[ -z "$COUNT" ] && COUNT="0" # Zero means indefinitely
if [ -n "$DST_PORT" ]; then
- read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT)
- validate_ports $DST_MIN $DST_MAX
+ read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT)
+ validate_ports $UDP_DST_MIN $UDP_DST_MAX
fi
# NOTICE: Script specific settings
@@ -63,8 +63,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do
if [ -n "$DST_PORT" ]; then
# Single destination port or random port range
pg_set $dev "flag UDPDST_RND"
- pg_set $dev "udp_dst_min $DST_MIN"
- pg_set $dev "udp_dst_max $DST_MAX"
+ pg_set $dev "udp_dst_min $UDP_DST_MIN"
+ pg_set $dev "udp_dst_max $UDP_DST_MAX"
fi
# Randomize source IP-addresses
@@ -23,8 +23,8 @@ source ${basedir}/parameters.sh
[ -z "$BURST" ] && BURST=32
[ -z "$COUNT" ] && COUNT="0" # Zero means indefinitely
if [ -n "$DST_PORT" ]; then
- read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT)
- validate_ports $DST_MIN $DST_MAX
+ read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT)
+ validate_ports $UDP_DST_MIN $UDP_DST_MAX
fi
# Base Config
@@ -56,8 +56,8 @@ for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do
if [ -n "$DST_PORT" ]; then
# Single destination port or random port range
pg_set $dev "flag UDPDST_RND"
- pg_set $dev "udp_dst_min $DST_MIN"
- pg_set $dev "udp_dst_max $DST_MAX"
+ pg_set $dev "udp_dst_min $UDP_DST_MIN"
+ pg_set $dev "udp_dst_max $UDP_DST_MAX"
fi
# Setup source IP-addresses based on thread number
@@ -20,8 +20,8 @@ DELAY="0" # Zero means max speed
[ -z "$CLONE_SKB" ] && CLONE_SKB="0"
# Flow variation random source port between min and max
-UDP_MIN=9
-UDP_MAX=109
+UDP_SRC_MIN=9
+UDP_SRC_MAX=109
node=`get_iface_node $DEV`
irq_array=(`get_iface_irqs $DEV`)
@@ -36,8 +36,8 @@ if [ -z "$DEST_IP" ]; then
fi
[ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff"
if [ -n "$DST_PORT" ]; then
- read -r DST_MIN DST_MAX <<< $(parse_ports $DST_PORT)
- validate_ports $DST_MIN $DST_MAX
+ read -r UDP_DST_MIN UDP_DST_MAX <<< $(parse_ports $DST_PORT)
+ validate_ports $UDP_DST_MIN $UDP_DST_MAX
fi
# General cleanup everything since last run
@@ -84,14 +84,14 @@ for ((i = 0; i < $THREADS; i++)); do
if [ -n "$DST_PORT" ]; then
# Single destination port or random port range
pg_set $dev "flag UDPDST_RND"
- pg_set $dev "udp_dst_min $DST_MIN"
- pg_set $dev "udp_dst_max $DST_MAX"
+ pg_set $dev "udp_dst_min $UDP_DST_MIN"
+ pg_set $dev "udp_dst_max $UDP_DST_MAX"
fi
# Setup random UDP port src range
pg_set $dev "flag UDPSRC_RND"
- pg_set $dev "udp_src_min $UDP_MIN"
- pg_set $dev "udp_src_max $UDP_MAX"
+ pg_set $dev "udp_src_min $UDP_SRC_MIN"
+ pg_set $dev "udp_src_max $UDP_SRC_MAX"
done
# start_run
This commit changes variable names that can cause confusion. For example, variable DST_MIN is quite confusing since the keyword 'udp_dst_min' and keyword 'dst_min' is used with pg_ctrl. On the following commit, 'dst_min' will be used to set destination IP, and the existing variable name DST_MIN should be changed. Variable names are matched to the exact keyword used with pg_ctrl. Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com> --- .../pktgen_bench_xmit_mode_netif_receive.sh | 8 ++++---- .../pktgen/pktgen_bench_xmit_mode_queue_xmit.sh | 8 ++++---- samples/pktgen/pktgen_sample01_simple.sh | 16 ++++++++-------- samples/pktgen/pktgen_sample02_multiqueue.sh | 16 ++++++++-------- .../pktgen/pktgen_sample03_burst_single_flow.sh | 8 ++++---- samples/pktgen/pktgen_sample04_many_flows.sh | 8 ++++---- .../pktgen/pktgen_sample05_flow_per_thread.sh | 8 ++++---- ...en_sample06_numa_awared_queue_irq_affinity.sh | 16 ++++++++-------- 8 files changed, 44 insertions(+), 44 deletions(-)