| Message ID | 20190821154745.31834-3-jonnyc@amazon.com |
|---|---|
| State | Accepted |
| Delegated to: | Lorenzo Pieralisi |
| Headers | show |
| Series | Amazon's Annapurna Labs DT-based PCIe host controller driver | expand |
On Wed, Aug 21, 2019 at 06:47:45PM +0300, Jonathan Chocron wrote: > Some PCIe controllers can be set to either Host or EP according to some > early boot FW. To make sure there is no discrepancy (e.g. FW configured > the port to EP mode while the DT specifies it as a host bridge or vice > versa), a check has been added for each mode. > > Signed-off-by: Jonathan Chocron <jonnyc@amazon.com> > Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> > --- > drivers/pci/controller/dwc/pcie-designware-ep.c | 8 ++++++++ > drivers/pci/controller/dwc/pcie-designware-host.c | 8 ++++++++ > 2 files changed, 16 insertions(+) > > diff --git a/drivers/pci/controller/dwc/pcie-designware-ep.c b/drivers/pci/controller/dwc/pcie-designware-ep.c > index 2bf5a35c0570..00e59a134b93 100644 > --- a/drivers/pci/controller/dwc/pcie-designware-ep.c > +++ b/drivers/pci/controller/dwc/pcie-designware-ep.c > @@ -531,6 +531,7 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) > int ret; > u32 reg; > void *addr; > + u8 hdr_type; > unsigned int nbars; > unsigned int offset; > struct pci_epc *epc; > @@ -543,6 +544,13 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) > return -EINVAL; > } > > + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); > + if (hdr_type != PCI_HEADER_TYPE_NORMAL) { > + dev_err(pci->dev, "PCIe controller is not set to EP mode (hdr_type:0x%x)!\n", > + hdr_type); > + return -EIO; > + } > + > ret = of_property_read_u32(np, "num-ib-windows", &ep->num_ib_windows); > if (ret < 0) { > dev_err(dev, "Unable to read *num-ib-windows* property\n"); > diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c > index f93252d0da5b..d2ca748e4c85 100644 > --- a/drivers/pci/controller/dwc/pcie-designware-host.c > +++ b/drivers/pci/controller/dwc/pcie-designware-host.c > @@ -323,6 +323,7 @@ int dw_pcie_host_init(struct pcie_port *pp) > struct pci_bus *child; > struct pci_host_bridge *bridge; > struct resource *cfg_res; > + u8 hdr_type; > int ret; > > raw_spin_lock_init(&pci->pp.lock); > @@ -396,6 +397,13 @@ int dw_pcie_host_init(struct pcie_port *pp) > } > } > > + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); Do we know if it's always safe to read these registers at this point in time? Later in dw_pcie_host_init we call pp->ops->host_init - looking at the implementations of .host_init I can see: - resets being performed (qcom_ep_reset_assert, artpec6_pcie_assert_core_reset, imx6_pcie_assert_core_reset) - changes to config space registers (ks_pcie_init_id, dw_pcie_setup_rc) including setting PCI_CLASS_DEVICE - and clocks being enabled (qcom_pcie_init_1_0_0) I'm not sure if your changes would cause anything to break for these other controllers (or future controllers) as I couldn't see any other reads to the config. Given that we are reading config space should dw_pcie_rd_own_conf be used? (For example kirin_pcie_rd_own_conf does something special). Thanks, Andrew Murray > + if (hdr_type != PCI_HEADER_TYPE_BRIDGE) { > + dev_err(pci->dev, "PCIe controller is not set to bridge type (hdr_type: 0x%x)!\n", > + hdr_type); > + return -EIO; > + } > + > pp->mem_base = pp->mem->start; > > if (!pp->va_cfg0_base) { > -- > 2.17.1 >
On Thu, 2019-08-22 at 12:13 +0100, Andrew Murray wrote: > On Wed, Aug 21, 2019 at 06:47:45PM +0300, Jonathan Chocron wrote: > > Some PCIe controllers can be set to either Host or EP according to > > some > > early boot FW. To make sure there is no discrepancy (e.g. FW > > configured > > the port to EP mode while the DT specifies it as a host bridge or > > vice > > versa), a check has been added for each mode. > > > > Signed-off-by: Jonathan Chocron <jonnyc@amazon.com> > > Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> > > --- > > drivers/pci/controller/dwc/pcie-designware-ep.c | 8 ++++++++ > > drivers/pci/controller/dwc/pcie-designware-host.c | 8 ++++++++ > > 2 files changed, 16 insertions(+) > > > > diff --git a/drivers/pci/controller/dwc/pcie-designware-ep.c > > b/drivers/pci/controller/dwc/pcie-designware-ep.c > > index 2bf5a35c0570..00e59a134b93 100644 > > --- a/drivers/pci/controller/dwc/pcie-designware-ep.c > > +++ b/drivers/pci/controller/dwc/pcie-designware-ep.c > > @@ -531,6 +531,7 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) > > int ret; > > u32 reg; > > void *addr; > > + u8 hdr_type; > > unsigned int nbars; > > unsigned int offset; > > struct pci_epc *epc; > > @@ -543,6 +544,13 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) > > return -EINVAL; > > } > > > > + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); > > + if (hdr_type != PCI_HEADER_TYPE_NORMAL) { > > + dev_err(pci->dev, "PCIe controller is not set to EP > > mode (hdr_type:0x%x)!\n", > > + hdr_type); > > + return -EIO; > > + } > > + > > ret = of_property_read_u32(np, "num-ib-windows", &ep- > > >num_ib_windows); > > if (ret < 0) { > > dev_err(dev, "Unable to read *num-ib-windows* > > property\n"); > > diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c > > b/drivers/pci/controller/dwc/pcie-designware-host.c > > index f93252d0da5b..d2ca748e4c85 100644 > > --- a/drivers/pci/controller/dwc/pcie-designware-host.c > > +++ b/drivers/pci/controller/dwc/pcie-designware-host.c > > @@ -323,6 +323,7 @@ int dw_pcie_host_init(struct pcie_port *pp) > > struct pci_bus *child; > > struct pci_host_bridge *bridge; > > struct resource *cfg_res; > > + u8 hdr_type; > > int ret; > > > > raw_spin_lock_init(&pci->pp.lock); > > @@ -396,6 +397,13 @@ int dw_pcie_host_init(struct pcie_port *pp) > > } > > } > > > > + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); > > Do we know if it's always safe to read these registers at this point > in time? > > Later in dw_pcie_host_init we call pp->ops->host_init - looking at > the > implementations of .host_init I can see: > > - resets being performed (qcom_ep_reset_assert, > artpec6_pcie_assert_core_reset, imx6_pcie_assert_core_reset) > - changes to config space registers (ks_pcie_init_id, > dw_pcie_setup_rc) > including setting PCI_CLASS_DEVICE > - and clocks being enabled (qcom_pcie_init_1_0_0) > Good point! This indeed might break host drivers which actually setup the rc in the kernel, and don't depend on early boot FW. So the validation should probably be moved to after pp->ops->host_init() (and similarly after ep->ops->ep_init() for the ep driver), right? > I'm not sure if your changes would cause anything to break for these > other > controllers (or future controllers) as I couldn't see any other reads > to the > config. > > Given that we are reading config space should dw_pcie_rd_own_conf be > used? The config space of the DW core is located at the beginning of the DBI regspace. Furthermore, this would break the "symmetry" between the host and ep validations (since the ep has no notion of reading from config space nor a .read callback in struct dw_pcie_ep_ops). I agree that there is some sort of overlap between the dw_pcie_read{/write}_dbi dw_pcie_rd{/wr}_own_conf APIs, when accessing the host mode config space, but I assume that any host driver which supplies a callback for .rd_own_conf() must supply an equivalent .read_dbi() one as well. > (For example kirin_pcie_rd_own_conf does something special). > They specifically define an equivalent kirin_pcie_read_dbi(). > Thanks, > > Andrew Murray > > > + if (hdr_type != PCI_HEADER_TYPE_BRIDGE) { > > + dev_err(pci->dev, "PCIe controller is not set to bridge > > type (hdr_type: 0x%x)!\n", > > + hdr_type); > > + return -EIO; > > + } > > + > > pp->mem_base = pp->mem->start; > > > > if (!pp->va_cfg0_base) { > > -- > > 2.17.1 > >
On Thu, Aug 22, 2019 at 04:30:09PM +0000, Chocron, Jonathan wrote: > On Thu, 2019-08-22 at 12:13 +0100, Andrew Murray wrote: > > On Wed, Aug 21, 2019 at 06:47:45PM +0300, Jonathan Chocron wrote: > > > Some PCIe controllers can be set to either Host or EP according to > > > some > > > early boot FW. To make sure there is no discrepancy (e.g. FW > > > configured > > > the port to EP mode while the DT specifies it as a host bridge or > > > vice > > > versa), a check has been added for each mode. > > > > > > Signed-off-by: Jonathan Chocron <jonnyc@amazon.com> > > > Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> > > > --- > > > drivers/pci/controller/dwc/pcie-designware-ep.c | 8 ++++++++ > > > drivers/pci/controller/dwc/pcie-designware-host.c | 8 ++++++++ > > > 2 files changed, 16 insertions(+) > > > > > > diff --git a/drivers/pci/controller/dwc/pcie-designware-ep.c > > > b/drivers/pci/controller/dwc/pcie-designware-ep.c > > > index 2bf5a35c0570..00e59a134b93 100644 > > > --- a/drivers/pci/controller/dwc/pcie-designware-ep.c > > > +++ b/drivers/pci/controller/dwc/pcie-designware-ep.c > > > @@ -531,6 +531,7 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) > > > int ret; > > > u32 reg; > > > void *addr; > > > + u8 hdr_type; > > > unsigned int nbars; > > > unsigned int offset; > > > struct pci_epc *epc; > > > @@ -543,6 +544,13 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) > > > return -EINVAL; > > > } > > > > > > + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); > > > + if (hdr_type != PCI_HEADER_TYPE_NORMAL) { > > > + dev_err(pci->dev, "PCIe controller is not set to EP > > > mode (hdr_type:0x%x)!\n", > > > + hdr_type); > > > + return -EIO; > > > + } > > > + > > > ret = of_property_read_u32(np, "num-ib-windows", &ep- > > > >num_ib_windows); > > > if (ret < 0) { > > > dev_err(dev, "Unable to read *num-ib-windows* > > > property\n"); > > > diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c > > > b/drivers/pci/controller/dwc/pcie-designware-host.c > > > index f93252d0da5b..d2ca748e4c85 100644 > > > --- a/drivers/pci/controller/dwc/pcie-designware-host.c > > > +++ b/drivers/pci/controller/dwc/pcie-designware-host.c > > > @@ -323,6 +323,7 @@ int dw_pcie_host_init(struct pcie_port *pp) > > > struct pci_bus *child; > > > struct pci_host_bridge *bridge; > > > struct resource *cfg_res; > > > + u8 hdr_type; > > > int ret; > > > > > > raw_spin_lock_init(&pci->pp.lock); > > > @@ -396,6 +397,13 @@ int dw_pcie_host_init(struct pcie_port *pp) > > > } > > > } > > > > > > + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); > > > > Do we know if it's always safe to read these registers at this point > > in time? > > > > Later in dw_pcie_host_init we call pp->ops->host_init - looking at > > the > > implementations of .host_init I can see: > > > > - resets being performed (qcom_ep_reset_assert, > > artpec6_pcie_assert_core_reset, imx6_pcie_assert_core_reset) > > - changes to config space registers (ks_pcie_init_id, > > dw_pcie_setup_rc) > > including setting PCI_CLASS_DEVICE > > - and clocks being enabled (qcom_pcie_init_1_0_0) > > > Good point! This indeed might break host drivers which actually setup > the rc in the kernel, and don't depend on early boot FW. So the > validation should probably be moved to after pp->ops->host_init() (and > similarly after ep->ops->ep_init() for the ep driver), right? Yes I think so. > > > I'm not sure if your changes would cause anything to break for these > > other > > controllers (or future controllers) as I couldn't see any other reads > > to the > > config. > > > > Given that we are reading config space should dw_pcie_rd_own_conf be > > used? > > The config space of the DW core is located at the beginning of the DBI > regspace. Furthermore, this would break the "symmetry" between the host > and ep validations (since the ep has no notion of reading from config > space nor a .read callback in struct dw_pcie_ep_ops). This is true, though given how different the two drivers are - this is only really 'nice to have'. > I agree that > there is some sort of overlap between the dw_pcie_read{/write}_dbi > dw_pcie_rd{/wr}_own_conf APIs, when accessing the host mode config > space, but I assume that any host driver which supplies a callback for > .rd_own_conf() must supply an equivalent .read_dbi() one as well. > > > (For example kirin_pcie_rd_own_conf does something special). > > > They specifically define an equivalent kirin_pcie_read_dbi(). This may also be true. However given that the dwc framework gives host drivers the ability to provide their own rd_own_conf callback - it's very possible that these drivers can use the callback to handle quirks - now or in the future. Potentially a quirk that your direct reading won't handle. Looking at the existing drivers which provide a .rd_own_conf: pci-exynos.c: - Uses dw_pcie_read to directly read from registers, sandwich'd between writes to set/clear PCIE_ELBI_SLV_ARMISC. This driver provides a .read_dbi which means dw_pcie_readb_dbi probably does the same thing as rd_own_conf. pci-menson.c: - Uses dw_pcie_read to directly read from registers, it then applies a read quirk for the PCI_CLASS_DEVICE register. This driver doesn't provide a .read_dbi - thus dw_pcie_readb_dbi probably does the same thing as rd_own_conf provided you don't read the PCI_CLASS_DEVICE register. pcie-hisi.c: - Uses dw_pcie_readl_dbi to read from registers, but the controller only supports 32bit aligned reads - it doesn't provide a .read_dbi. This means that if you used dw_pcie_readb_dbi it'd probably break because you can't read 1 byte at the offset where HEADER_TYPE is. pcie-histb.c, pcie-kirin.c: looks like pci-exynos.c It looks like we're going to have to break symmetry... Thanks, Andrew Murray > > > Thanks, > > > > Andrew Murray > > > > > + if (hdr_type != PCI_HEADER_TYPE_BRIDGE) { > > > + dev_err(pci->dev, "PCIe controller is not set to bridge > > > type (hdr_type: 0x%x)!\n", > > > + hdr_type); > > > + return -EIO; > > > + } > > > + > > > pp->mem_base = pp->mem->start; > > > > > > if (!pp->va_cfg0_base) { > > > -- > > > 2.17.1 > > >
On Tue, 2019-08-27 at 10:48 +0100, Andrew Murray wrote: > On Thu, Aug 22, 2019 at 04:30:09PM +0000, Chocron, Jonathan wrote: > > On Thu, 2019-08-22 at 12:13 +0100, Andrew Murray wrote: > > > On Wed, Aug 21, 2019 at 06:47:45PM +0300, Jonathan Chocron wrote: > > > > Some PCIe controllers can be set to either Host or EP according > > > > to > > > > some > > > > early boot FW. To make sure there is no discrepancy (e.g. FW > > > > configured > > > > the port to EP mode while the DT specifies it as a host bridge > > > > or > > > > vice > > > > versa), a check has been added for each mode. > > > > > > > > Signed-off-by: Jonathan Chocron <jonnyc@amazon.com> > > > > Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> > > > > --- > > > > drivers/pci/controller/dwc/pcie-designware-ep.c | 8 ++++++++ > > > > drivers/pci/controller/dwc/pcie-designware-host.c | 8 ++++++++ > > > > 2 files changed, 16 insertions(+) > > > > > > > > diff --git a/drivers/pci/controller/dwc/pcie-designware-ep.c > > > > b/drivers/pci/controller/dwc/pcie-designware-ep.c > > > > index 2bf5a35c0570..00e59a134b93 100644 > > > > --- a/drivers/pci/controller/dwc/pcie-designware-ep.c > > > > +++ b/drivers/pci/controller/dwc/pcie-designware-ep.c > > > > @@ -531,6 +531,7 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) > > > > int ret; > > > > u32 reg; > > > > void *addr; > > > > + u8 hdr_type; > > > > unsigned int nbars; > > > > unsigned int offset; > > > > struct pci_epc *epc; > > > > @@ -543,6 +544,13 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) > > > > return -EINVAL; > > > > } > > > > > > > > + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); > > > > + if (hdr_type != PCI_HEADER_TYPE_NORMAL) { > > > > + dev_err(pci->dev, "PCIe controller is not set > > > > to EP > > > > mode (hdr_type:0x%x)!\n", > > > > + hdr_type); > > > > + return -EIO; > > > > + } > > > > + > > > > ret = of_property_read_u32(np, "num-ib-windows", &ep- > > > > > num_ib_windows); > > > > > > > > if (ret < 0) { > > > > dev_err(dev, "Unable to read *num-ib-windows* > > > > property\n"); > > > > diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c > > > > b/drivers/pci/controller/dwc/pcie-designware-host.c > > > > index f93252d0da5b..d2ca748e4c85 100644 > > > > --- a/drivers/pci/controller/dwc/pcie-designware-host.c > > > > +++ b/drivers/pci/controller/dwc/pcie-designware-host.c > > > > @@ -323,6 +323,7 @@ int dw_pcie_host_init(struct pcie_port *pp) > > > > struct pci_bus *child; > > > > struct pci_host_bridge *bridge; > > > > struct resource *cfg_res; > > > > + u8 hdr_type; > > > > int ret; > > > > > > > > raw_spin_lock_init(&pci->pp.lock); > > > > @@ -396,6 +397,13 @@ int dw_pcie_host_init(struct pcie_port > > > > *pp) > > > > } > > > > } > > > > > > > > + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); > > > > > > Do we know if it's always safe to read these registers at this > > > point > > > in time? > > > > > > Later in dw_pcie_host_init we call pp->ops->host_init - looking > > > at > > > the > > > implementations of .host_init I can see: > > > > > > - resets being performed (qcom_ep_reset_assert, > > > artpec6_pcie_assert_core_reset, imx6_pcie_assert_core_reset) > > > - changes to config space registers (ks_pcie_init_id, > > > dw_pcie_setup_rc) > > > including setting PCI_CLASS_DEVICE > > > - and clocks being enabled (qcom_pcie_init_1_0_0) > > > > > > > Good point! This indeed might break host drivers which actually > > setup > > the rc in the kernel, and don't depend on early boot FW. So the > > validation should probably be moved to after pp->ops->host_init() > > (and > > similarly after ep->ops->ep_init() for the ep driver), right? > > Yes I think so. > Done as part of v5. > > > > > > I'm not sure if your changes would cause anything to break for > > > these > > > other > > > controllers (or future controllers) as I couldn't see any other > > > reads > > > to the > > > config. > > > > > > Given that we are reading config space should dw_pcie_rd_own_conf > > > be > > > used? > > > > The config space of the DW core is located at the beginning of the > > DBI > > regspace. Furthermore, this would break the "symmetry" between the > > host > > and ep validations (since the ep has no notion of reading from > > config > > space nor a .read callback in struct dw_pcie_ep_ops). > > This is true, though given how different the two drivers are - this > is only > really 'nice to have'. > > > > I agree that > > there is some sort of overlap between the dw_pcie_read{/write}_dbi > > dw_pcie_rd{/wr}_own_conf APIs, when accessing the host mode config > > space, but I assume that any host driver which supplies a callback > > for > > .rd_own_conf() must supply an equivalent .read_dbi() one as well. > > > > > (For example kirin_pcie_rd_own_conf does something special). > > > > > > > They specifically define an equivalent kirin_pcie_read_dbi(). > > This may also be true. However given that the dwc framework gives > host drivers > the ability to provide their own rd_own_conf callback - it's very > possible > that these drivers can use the callback to handle quirks - now or in > the > future. Potentially a quirk that your direct reading won't handle. > > Looking at the existing drivers which provide a .rd_own_conf: > > pci-exynos.c: > - Uses dw_pcie_read to directly read from registers, sandwich'd > between writes > to set/clear PCIE_ELBI_SLV_ARMISC. This driver provides a > .read_dbi which > means dw_pcie_readb_dbi probably does the same thing as > rd_own_conf. > > pci-menson.c: > - Uses dw_pcie_read to directly read from registers, it then applies > a read > quirk for the PCI_CLASS_DEVICE register. This driver doesn't > provide a > .read_dbi - thus dw_pcie_readb_dbi probably does the same thing as > rd_own_conf provided you don't read the PCI_CLASS_DEVICE register. > > pcie-hisi.c: > - Uses dw_pcie_readl_dbi to read from registers, but the controller > only > supports 32bit aligned reads - it doesn't provide a .read_dbi. > This means > that if you used dw_pcie_readb_dbi it'd probably break because you > can't > read 1 byte at the offset where HEADER_TYPE is. > > pcie-histb.c, pcie-kirin.c: looks like pci-exynos.c > > It looks like we're going to have to break symmetry... > Done as part of v5. Thanks for your insightful review. > Thanks, > > Andrew Murray > > > > > > Thanks, > > > > > > Andrew Murray > > > > > > > + if (hdr_type != PCI_HEADER_TYPE_BRIDGE) { > > > > + dev_err(pci->dev, "PCIe controller is not set > > > > to bridge > > > > type (hdr_type: 0x%x)!\n", > > > > + hdr_type); > > > > + return -EIO; > > > > + } > > > > + > > > > pp->mem_base = pp->mem->start; > > > > > > > > if (!pp->va_cfg0_base) { > > > > -- > > > > 2.17.1 > > > >
diff --git a/drivers/pci/controller/dwc/pcie-designware-ep.c b/drivers/pci/controller/dwc/pcie-designware-ep.c index 2bf5a35c0570..00e59a134b93 100644 --- a/drivers/pci/controller/dwc/pcie-designware-ep.c +++ b/drivers/pci/controller/dwc/pcie-designware-ep.c @@ -531,6 +531,7 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) int ret; u32 reg; void *addr; + u8 hdr_type; unsigned int nbars; unsigned int offset; struct pci_epc *epc; @@ -543,6 +544,13 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep) return -EINVAL; } + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); + if (hdr_type != PCI_HEADER_TYPE_NORMAL) { + dev_err(pci->dev, "PCIe controller is not set to EP mode (hdr_type:0x%x)!\n", + hdr_type); + return -EIO; + } + ret = of_property_read_u32(np, "num-ib-windows", &ep->num_ib_windows); if (ret < 0) { dev_err(dev, "Unable to read *num-ib-windows* property\n"); diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c index f93252d0da5b..d2ca748e4c85 100644 --- a/drivers/pci/controller/dwc/pcie-designware-host.c +++ b/drivers/pci/controller/dwc/pcie-designware-host.c @@ -323,6 +323,7 @@ int dw_pcie_host_init(struct pcie_port *pp) struct pci_bus *child; struct pci_host_bridge *bridge; struct resource *cfg_res; + u8 hdr_type; int ret; raw_spin_lock_init(&pci->pp.lock); @@ -396,6 +397,13 @@ int dw_pcie_host_init(struct pcie_port *pp) } } + hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE); + if (hdr_type != PCI_HEADER_TYPE_BRIDGE) { + dev_err(pci->dev, "PCIe controller is not set to bridge type (hdr_type: 0x%x)!\n", + hdr_type); + return -EIO; + } + pp->mem_base = pp->mem->start; if (!pp->va_cfg0_base) {