| Message ID | 20190719065743.28192-3-manivannan.sadhasivam@linaro.org |
|---|---|
| State | Superseded |
| Delegated to: | Stefano Babic |
| Headers | show |
| Series | Add board support for iMX8QXP AI_ML board | expand |
Hi Manivannan, > This commit adds initial board support for iMX8QXP AI_ML board from > Einfochips. This board is one of the 96Boards Consumer Edition and AI > boards of the 96Boards family based on i.MX8QXP SoC from > NXP/Freescale. > > This initial supports contains following peripherals which are tested > and known to work: > > 1. Debug serial via UART2 > 2. SD card > 3. Ethernet > > More information about this board can be found in arrow website: > https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools > > Signed-off-by: Manivannan Sadhasivam > <manivannan.sadhasivam@linaro.org> --- > arch/arm/mach-imx/imx8/Kconfig | 6 + > board/einfochips/imx8qxp_ai_ml/Kconfig | 12 ++ > board/einfochips/imx8qxp_ai_ml/MAINTAINERS | 6 + > board/einfochips/imx8qxp_ai_ml/Makefile | 8 ++ > board/einfochips/imx8qxp_ai_ml/README | 49 ++++++++ > .../einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c | 117 > ++++++++++++++++++ board/einfochips/imx8qxp_ai_ml/imximage.cfg | > 24 ++++ board/einfochips/imx8qxp_ai_ml/spl.c | 49 ++++++++ > configs/imx8qxp_ai_ml_defconfig | 83 +++++++++++++ > include/configs/imx8qxp_ai_ml.h | 104 ++++++++++++++++ > 10 files changed, 458 insertions(+) > create mode 100644 board/einfochips/imx8qxp_ai_ml/Kconfig > create mode 100644 board/einfochips/imx8qxp_ai_ml/MAINTAINERS > create mode 100644 board/einfochips/imx8qxp_ai_ml/Makefile > create mode 100644 board/einfochips/imx8qxp_ai_ml/README > create mode 100644 board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > create mode 100644 board/einfochips/imx8qxp_ai_ml/imximage.cfg > create mode 100644 board/einfochips/imx8qxp_ai_ml/spl.c > create mode 100644 configs/imx8qxp_ai_ml_defconfig > create mode 100644 include/configs/imx8qxp_ai_ml.h > > diff --git a/arch/arm/mach-imx/imx8/Kconfig > b/arch/arm/mach-imx/imx8/Kconfig index bbe323d5ca..cec21f8dd2 100644 > --- a/arch/arm/mach-imx/imx8/Kconfig > +++ b/arch/arm/mach-imx/imx8/Kconfig > @@ -37,6 +37,11 @@ config TARGET_COLIBRI_IMX8X > select BOARD_LATE_INIT > select IMX8QXP > > +config TARGET_IMX8QXP_AI_ML > + bool "Support i.MX8QXP AI_ML board" > + select BOARD_LATE_INIT > + select IMX8QXP > + > config TARGET_IMX8QM_MEK > bool "Support i.MX8QM MEK board" > select BOARD_LATE_INIT > @@ -49,6 +54,7 @@ config TARGET_IMX8QXP_MEK > > endchoice > > +source "board/einfochips/imx8qxp_ai_ml/Kconfig" > source "board/freescale/imx8qm_mek/Kconfig" > source "board/freescale/imx8qxp_mek/Kconfig" > source "board/toradex/apalis-imx8/Kconfig" > diff --git a/board/einfochips/imx8qxp_ai_ml/Kconfig > b/board/einfochips/imx8qxp_ai_ml/Kconfig new file mode 100644 > index 0000000000..697a831013 > --- /dev/null > +++ b/board/einfochips/imx8qxp_ai_ml/Kconfig > @@ -0,0 +1,12 @@ > +if TARGET_IMX8QXP_AI_ML > + > +config SYS_BOARD > + default "imx8qxp_ai_ml" > + > +config SYS_VENDOR > + default "einfochips" > + > +config SYS_CONFIG_NAME > + default "imx8qxp_ai_ml" > + > +endif > diff --git a/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS new file mode 100644 > index 0000000000..add0bd9431 > --- /dev/null > +++ b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > @@ -0,0 +1,6 @@ > +i.MX8QXP AI_ML BOARD > +M: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > +S: Maintained > +F: board/einfochips/imx8qxp_ai_ml/ > +F: include/configs/imx8qxp_ai_ml.h > +F: configs/imx8qxp_ai_ml_defconfig > diff --git a/board/einfochips/imx8qxp_ai_ml/Makefile > b/board/einfochips/imx8qxp_ai_ml/Makefile new file mode 100644 > index 0000000000..e08774dc6e > --- /dev/null > +++ b/board/einfochips/imx8qxp_ai_ml/Makefile > @@ -0,0 +1,8 @@ > +# > +# Copyright 2019 Linaro Ltd. > +# > +# SPDX-License-Identifier: GPL-2.0+ > +# > + > +obj-y += imx8qxp_ai_ml.o > +obj-$(CONFIG_SPL_BUILD) += spl.o > diff --git a/board/einfochips/imx8qxp_ai_ml/README > b/board/einfochips/imx8qxp_ai_ml/README new file mode 100644 > index 0000000000..488920580f > --- /dev/null > +++ b/board/einfochips/imx8qxp_ai_ml/README Thank you for preparing the README file, appreciated :-). > @@ -0,0 +1,49 @@ > +U-Boot for the Einfochips i.MX8QXP AI_ML board > + > +Quick Start > +=========== > + > +- Get and Build the ARM Trusted firmware > +- Get scfw_tcm.bin and ahab-container.img > +- Build U-Boot > +- Flash the binary into the SD card > +- Boot > + > +Get and Build the ARM Trusted firmware > +====================================== > + > +$ git clone https://source.codeaurora.org/external/imx/imx-atf > +$ cd imx-atf/ > +$ git checkout origin/imx_4.9.88_imx8qxp_beta2 -b > imx_4.9.88_imx8qxp_beta2 +$ make PLAT=imx8qxp bl31 > + > +Get scfw_tcm.bin and ahab-container.img > +======================================= > + > +$ wget > https://raw.githubusercontent.com/96boards-ai-ml/binaries/master/mx8qx-aiml-scfw-tcm.bin > +$ wget > https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.1.bin +$ > chmod +x firmware-imx-8.1.bin +$ ./firmware-imx-8.1.bin + > +Copy the following binaries to U-Boot folder: > + > +$ cp imx-atf/build/imx8qxp/release/bl31.bin . > +$ cp firmware-imx-8.1/firmware/seco/mx8qx-ahab-container.img . > + > +Build U-Boot > +============ > + > +$ make imx8qxp_ai_ml_defconfig > +$ make u-boot-dtb.imx > + > +Flash the binary into the SD card > +================================= > + > +Burn the u-boot-dtb.imx binary to SD card offset 32KB: > + > +$ sudo dd if=u-boot-dtb.imx of=/dev/sd[x] bs=1024 seek=32 > + > +Boot > +==== > + > +Set Boot switch SW2: 1100. > diff --git a/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c new file mode 100644 > index 0000000000..e7632524a0 > --- /dev/null > +++ b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > @@ -0,0 +1,117 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2018 NXP > + * Copyright 2019 Linaro Ltd. > + */ > + > +#include <common.h> > +#include <errno.h> > +#include <linux/libfdt.h> > +#include <environment.h> > +#include <fsl_esdhc.h> > +#include <asm/io.h> > +#include <asm/arch/clock.h> > +#include <asm/arch/sci/sci.h> > +#include <asm/arch/imx8-pins.h> > +#include <asm/arch/iomux.h> > +#include <asm/arch/sys_proto.h> > + > +DECLARE_GLOBAL_DATA_PTR; > + > +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << > PADRING_CONFIG_SHIFT) | \ > + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) > | \ > + (SC_PAD_28FDSOI_DSE_DV_HIGH << > PADRING_DSE_SHIFT) | \ > + (SC_PAD_28FDSOI_PS_PU << > PADRING_PULL_SHIFT)) + > +static iomux_cfg_t uart2_pads[] = { > + SC_P_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL), > + SC_P_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL), > +}; As fair as I see - the uart could be configured via DTS (by using the pinmux driver) as this is the U-Boot proper file. > + > +static void setup_iomux_uart(void) > +{ > + imx8_iomux_setup_multiple_pads(uart2_pads, > ARRAY_SIZE(uart2_pads)); +} > + > +int board_early_init_f(void) > +{ > + sc_pm_clock_rate_t rate = SC_80MHZ; > + int ret; > + > + /* Set UART2 clock root to 80 MHz */ > + ret = sc_pm_setup_uart(SC_R_UART_2, rate); > + if (ret) > + return ret; > + > + setup_iomux_uart(); > + > + return 0; > +} > + > +#if IS_ENABLED(CONFIG_DM_GPIO) > +static void board_gpio_init(void) > +{ > + /* TODO */ > +} > +#else > +static inline void board_gpio_init(void) {} > +#endif > + I'm wondering if the above function is needed? > +#if IS_ENABLED(CONFIG_FEC_MXC) > +#include <miiphy.h> > + > +int board_phy_config(struct phy_device *phydev) > +{ > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); > + > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); > + > + if (phydev->drv->config) > + phydev->drv->config(phydev); > + > + return 0; > +} > +#endif > + > +int checkboard(void) > +{ > + puts("Board: iMX8QXP AI_ML\n"); > + > + build_info(); > + print_bootinfo(); > + > + return 0; > +} > + > +int board_init(void) > +{ > + board_gpio_init(); > + > + return 0; > +} Here you call the empty board_gpio_init(). > + > +/* Board specific reset that is system reset */ > + > +void reset_cpu(ulong addr) > +{ > + /* TODO */ > +} Maybe you could use the SYSRESET driver from the outset? It internally uses WDT for reset. > + > +#ifdef CONFIG_OF_BOARD_SETUP > +int ft_board_setup(void *blob, bd_t *bd) > +{ > + return 0; > +} > +#endif > + > +int board_mmc_get_env_dev(int devno) > +{ > + return devno; > +} This (the device and its instance) could be set in Kconfig. > + > +int board_late_init(void) > +{ > + return 0; > +} > diff --git a/board/einfochips/imx8qxp_ai_ml/imximage.cfg > b/board/einfochips/imx8qxp_ai_ml/imximage.cfg new file mode 100644 > index 0000000000..4fc5ade313 > --- /dev/null > +++ b/board/einfochips/imx8qxp_ai_ml/imximage.cfg > @@ -0,0 +1,24 @@ > +/* SPDX-License-Identifier: GPL-2.0+ */ > +/* > + * Copyright 2018 NXP > + * > + * Refer doc/README.imx8image for more details about how-to configure > + * and create imx8image boot image > + */ > + > +#define __ASSEMBLY__ > + > +/* Boot from SD, sector size 0x400 */ > +BOOT_FROM SD 0x400 > +/* SoC type IMX8QX */ > +SOC_TYPE IMX8QX > +/* Append seco container image */ > +APPEND mx8qx-ahab-container.img > +/* Create the 2nd container */ > +CONTAINER > +/* Add scfw image with exec attribute */ > +IMAGE SCU mx8qx-aiml-scfw-tcm.bin > +/* Add ATF image with exec attribute */ > +IMAGE A35 bl31.bin 0x80000000 > +/* Add U-Boot image with load attribute */ > +DATA A35 u-boot-dtb.bin 0x80020000 > diff --git a/board/einfochips/imx8qxp_ai_ml/spl.c > b/board/einfochips/imx8qxp_ai_ml/spl.c new file mode 100644 > index 0000000000..63581eeaaf > --- /dev/null > +++ b/board/einfochips/imx8qxp_ai_ml/spl.c > @@ -0,0 +1,49 @@ > +/* > + * Copyright 2018 NXP > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#include <common.h> > +#include <dm.h> > +#include <spl.h> > +#include <dm/uclass.h> > +#include <dm/device.h> > +#include <dm/uclass-internal.h> > +#include <dm/device-internal.h> > +#include <dm/lists.h> > + > +DECLARE_GLOBAL_DATA_PTR; > + > +void spl_board_init(void) > +{ > + struct udevice *dev; > + > + uclass_find_first_device(UCLASS_MISC, &dev); > + > + for (; dev; uclass_find_next_device(&dev)) { > + if (device_probe(dev)) > + continue; > + } What devices needs to be initialized in that way ? > + > + arch_cpu_init(); > + > + board_early_init_f(); > + > + timer_init(); > + > + preloader_console_init(); > + > + puts("Normal Boot\n"); > +} > + > +void board_init_f(ulong dummy) > +{ > + /* Clear global data */ > + memset((void *)gd, 0, sizeof(gd_t)); > + > + /* Clear the BSS. */ > + memset(__bss_start, 0, __bss_end - __bss_start); > + > + board_init_r(NULL, 0); > +} > diff --git a/configs/imx8qxp_ai_ml_defconfig > b/configs/imx8qxp_ai_ml_defconfig new file mode 100644 > index 0000000000..e20a0c783e > --- /dev/null > +++ b/configs/imx8qxp_ai_ml_defconfig > @@ -0,0 +1,83 @@ > +CONFIG_ARM=y > +CONFIG_ARCH_IMX8=y > +CONFIG_SYS_TEXT_BASE=0x80020000 > +CONFIG_DISTRO_DEFAULTS=y > +CONFIG_SPL_GPIO_SUPPORT=y > +CONFIG_SPL_LIBCOMMON_SUPPORT=y > +CONFIG_SPL_LIBGENERIC_SUPPORT=y > +CONFIG_SYS_MALLOC_F_LEN=0x4000 > +CONFIG_TARGET_IMX8QXP_AI_ML=y > +CONFIG_SPL_MMC_SUPPORT=y > +CONFIG_SPL_SERIAL_SUPPORT=y > +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y > +CONFIG_NR_DRAM_BANKS=4 > +CONFIG_SPL=y > +CONFIG_FIT=y > +CONFIG_SPL_LOAD_FIT=y > +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/einfochips/imx8qxp_ai_ml/imximage.cfg" > +CONFIG_BOOTDELAY=3 > +CONFIG_LOG=y > +CONFIG_SPL_BOARD_INIT=y > +CONFIG_SPL_SYS_MALLOC_SIMPLE=y > +CONFIG_SPL_SEPARATE_BSS=y > +CONFIG_SPL_POWER_SUPPORT=y > +CONFIG_SPL_POWER_DOMAIN=y > +CONFIG_SPL_WATCHDOG_SUPPORT=y > +CONFIG_HUSH_PARSER=y > +CONFIG_CMD_CPU=y > +# CONFIG_CMD_IMPORTENV is not set > +CONFIG_CMD_CLK=y > +CONFIG_CMD_DM=y > +CONFIG_CMD_FUSE=y > +CONFIG_CMD_GPIO=y > +CONFIG_CMD_GPT=y > +CONFIG_CMD_I2C=y > +CONFIG_CMD_MMC=y > +CONFIG_CMD_DHCP=y > +CONFIG_CMD_MII=y > +CONFIG_CMD_PING=y > +CONFIG_CMD_CACHE=y > +CONFIG_CMD_EXT4=y > +CONFIG_CMD_EXT4_WRITE=y > +CONFIG_CMD_FAT=y > +CONFIG_FAT_WRITE=y > +CONFIG_CMD_FS_GENERIC=y > +CONFIG_SPL_OF_CONTROL=y > +CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qxp-ai_ml" > +CONFIG_ENV_IS_IN_MMC=y > +CONFIG_SPL_DM=y > +CONFIG_SPL_CLK=y > +CONFIG_CLK_IMX8=y > +CONFIG_CPU=y > +CONFIG_DM_GPIO=y > +CONFIG_MXC_GPIO=y > +CONFIG_DM_I2C=y > +CONFIG_SYS_I2C_IMX_LPI2C=y > +CONFIG_MISC=y > +CONFIG_DM_MMC=y > +CONFIG_FSL_ESDHC=y > +CONFIG_PHYLIB=y > +CONFIG_PHY_ADDR_ENABLE=y > +CONFIG_PHY_ATHEROS=y > +CONFIG_DM_ETH=y > +CONFIG_NET_RANDOM_ETHADDR=y > +CONFIG_PHY_GIGE=y > +CONFIG_FEC_MXC_SHARE_MDIO=y > +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000 > +CONFIG_FEC_MXC=y > +CONFIG_MII=y > +CONFIG_PINCTRL=y > +CONFIG_SPL_PINCTRL=y > +CONFIG_PINCTRL_IMX8=y > +CONFIG_POWER_DOMAIN=y > +CONFIG_IMX8_POWER_DOMAIN=y > +CONFIG_DM_REGULATOR=y > +CONFIG_SPL_DM_REGULATOR=y > +CONFIG_DM_REGULATOR_FIXED=y > +CONFIG_DM_REGULATOR_GPIO=y > +CONFIG_SPL_DM_REGULATOR_GPIO=y > +CONFIG_DM_SERIAL=y > +CONFIG_FSL_LPUART=y > +CONFIG_SPL_TINY_MEMSET=y > +# CONFIG_EFI_LOADER is not set > diff --git a/include/configs/imx8qxp_ai_ml.h > b/include/configs/imx8qxp_ai_ml.h new file mode 100644 > index 0000000000..dd31189845 > --- /dev/null > +++ b/include/configs/imx8qxp_ai_ml.h > @@ -0,0 +1,104 @@ > +/* SPDX-License-Identifier: GPL-2.0+ */ > +/* > + * Copyright 2018 NXP > + * Copyright 2019 Linaro Ltd. > + */ > + > +#ifndef __IMX8QXP_AI_ML_H > +#define __IMX8QXP_AI_ML_H > + > +#include <linux/sizes.h> > +#include <asm/arch/imx-regs.h> > + > +#ifdef CONFIG_SPL_BUILD > +#define CONFIG_SPL_MAX_SIZE (124 * > 1024) +#define CONFIG_SYS_MONITOR_LEN > (1024 * 1024) +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR > +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x250 > +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0 > + > +#define > CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" > +#define CONFIG_SPL_STACK 0x013E000 +#define > CONFIG_SPL_BSS_START_ADDR 0x00128000 +#define > CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */ > +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000 +#define > CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */ +#define > CONFIG_SERIAL_LPUART_BASE 0x5a080000 +#define > CONFIG_MALLOC_F_ADDR 0x00120000 + > +#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE > + > +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE > + > +#define CONFIG_OF_EMBED I'm not sure if the OF_EMBED is not deprecated ... and replaced by OF_SEPARATED. > +#endif > + > +#define CONFIG_REMAKE_ELF > + > +#define CONFIG_BOARD_EARLY_INIT_F This could be set in Kconfig, IIRC > + > +/* Flat Device Tree Definitions */ > +#define CONFIG_OF_BOARD_SETUP > + > +#define CONFIG_FSL_USDHC > + > +#define CONFIG_ENV_OVERWRITE > + > +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG > + > +#define BOOT_TARGET_DEVICES(func) \ > + func(MMC, mmc, 1) \ > + func(DHCP, dhcp, na) > + > +#include <config_distro_bootcmd.h> > +/* Initial environment variables */ > +#define CONFIG_EXTRA_ENV_SETTINGS \ > + "console=ttyLP2 earlycon\0" \ > + "fdt_addr_r=0x83000000\0" \ > + "kernel_addr_r=0x81000000\0" \ > + "ramdisk_addr_r=0x94400000\0" \ > + "scriptaddr=0x89000000\0" \ > + "fdtfile=imx8qxp-ai_ml.dtb\0" \ > + "fdt_high=0xffffffffffffffff\0" \ > + "image=Image\0" \ > + "initrd_addr=0x83800000\0" \ > + "initrd_high=0xffffffffffffffff\0" \ > + "netargs=setenv bootargs console=${console},${baudrate} " \ > + "root=/dev/nfs ip=dhcp > nfsroot=${serverip}:${nfsroot},v3,tcp" \ > + "\0" \ > + "nfsboot=run netargs; dhcp ${loadaddr} ${image}; tftp > ${fdt_addr} " \ > + "imx8qxp-ai_ml/${fdt_file}; booti ${loadaddr} - > ${fdt_addr}\0" \ > + BOOTENV > + > +/* Link Definitions */ > +#define CONFIG_LOADADDR 0x80280000 > + > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR > + > +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000 > + > +/* Default environment is in SD */ > +#define CONFIG_ENV_SIZE 0x1000 > +#define CONFIG_ENV_OFFSET (64 * SZ_64K) > + > +/* USDHC2 is the SD card interface */ > +#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */ > +#define CONFIG_SYS_FSL_USDHC_NUM 2 > + Some of those env setting defines as well as eMMC ones could be set now in Kconfig. > +/* Size of malloc() pool */ > +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 > * 1024)) * 1024) + > +#define CONFIG_SYS_SDRAM_BASE 0x80000000 > +#define PHYS_SDRAM_1 0x80000000 > +#define PHYS_SDRAM_2 0x880000000 > +#define PHYS_SDRAM_1_SIZE SZ_2G /* 2 Please fix this file globally, to use "SZ_XX" instead of magic numbers. > GB */ +#define PHYS_SDRAM_2_SIZE 0x00000000 /* > 0 GB */ + > +/* Generic Timer Definitions */ > +#define COUNTER_FREQUENCY 8000000 /* 8MHz */ > + > +/* Networking */ > +#define CONFIG_FEC_XCV_TYPE RGMII > +#define FEC_QUIRK_ENET_MAC > + > +#endif /* __IMX8QXP_AI_ML_H */ Best regards, Lukasz Majewski -- DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de
Hi Lukasz, Thanks for the review! On Wed, Jul 24, 2019 at 10:07:13AM +0200, Lukasz Majewski wrote: > Hi Manivannan, > > > This commit adds initial board support for iMX8QXP AI_ML board from > > Einfochips. This board is one of the 96Boards Consumer Edition and AI > > boards of the 96Boards family based on i.MX8QXP SoC from > > NXP/Freescale. > > > > This initial supports contains following peripherals which are tested > > and known to work: > > > > 1. Debug serial via UART2 > > 2. SD card > > 3. Ethernet > > > > More information about this board can be found in arrow website: > > https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools > > > > Signed-off-by: Manivannan Sadhasivam > > <manivannan.sadhasivam@linaro.org> --- > > arch/arm/mach-imx/imx8/Kconfig | 6 + > > board/einfochips/imx8qxp_ai_ml/Kconfig | 12 ++ > > board/einfochips/imx8qxp_ai_ml/MAINTAINERS | 6 + > > board/einfochips/imx8qxp_ai_ml/Makefile | 8 ++ > > board/einfochips/imx8qxp_ai_ml/README | 49 ++++++++ > > .../einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c | 117 > > ++++++++++++++++++ board/einfochips/imx8qxp_ai_ml/imximage.cfg | > > 24 ++++ board/einfochips/imx8qxp_ai_ml/spl.c | 49 ++++++++ > > configs/imx8qxp_ai_ml_defconfig | 83 +++++++++++++ > > include/configs/imx8qxp_ai_ml.h | 104 ++++++++++++++++ > > 10 files changed, 458 insertions(+) > > create mode 100644 board/einfochips/imx8qxp_ai_ml/Kconfig > > create mode 100644 board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > create mode 100644 board/einfochips/imx8qxp_ai_ml/Makefile > > create mode 100644 board/einfochips/imx8qxp_ai_ml/README > > create mode 100644 board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > create mode 100644 board/einfochips/imx8qxp_ai_ml/imximage.cfg > > create mode 100644 board/einfochips/imx8qxp_ai_ml/spl.c > > create mode 100644 configs/imx8qxp_ai_ml_defconfig > > create mode 100644 include/configs/imx8qxp_ai_ml.h > > > > diff --git a/arch/arm/mach-imx/imx8/Kconfig > > b/arch/arm/mach-imx/imx8/Kconfig index bbe323d5ca..cec21f8dd2 100644 > > --- a/arch/arm/mach-imx/imx8/Kconfig > > +++ b/arch/arm/mach-imx/imx8/Kconfig > > @@ -37,6 +37,11 @@ config TARGET_COLIBRI_IMX8X > > select BOARD_LATE_INIT > > select IMX8QXP > > > > +config TARGET_IMX8QXP_AI_ML > > + bool "Support i.MX8QXP AI_ML board" > > + select BOARD_LATE_INIT > > + select IMX8QXP > > + > > config TARGET_IMX8QM_MEK > > bool "Support i.MX8QM MEK board" > > select BOARD_LATE_INIT > > @@ -49,6 +54,7 @@ config TARGET_IMX8QXP_MEK > > > > endchoice > > > > +source "board/einfochips/imx8qxp_ai_ml/Kconfig" > > source "board/freescale/imx8qm_mek/Kconfig" > > source "board/freescale/imx8qxp_mek/Kconfig" > > source "board/toradex/apalis-imx8/Kconfig" > > diff --git a/board/einfochips/imx8qxp_ai_ml/Kconfig > > b/board/einfochips/imx8qxp_ai_ml/Kconfig new file mode 100644 > > index 0000000000..697a831013 > > --- /dev/null > > +++ b/board/einfochips/imx8qxp_ai_ml/Kconfig > > @@ -0,0 +1,12 @@ > > +if TARGET_IMX8QXP_AI_ML > > + > > +config SYS_BOARD > > + default "imx8qxp_ai_ml" > > + > > +config SYS_VENDOR > > + default "einfochips" > > + > > +config SYS_CONFIG_NAME > > + default "imx8qxp_ai_ml" > > + > > +endif > > diff --git a/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS new file mode 100644 > > index 0000000000..add0bd9431 > > --- /dev/null > > +++ b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > @@ -0,0 +1,6 @@ > > +i.MX8QXP AI_ML BOARD > > +M: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > +S: Maintained > > +F: board/einfochips/imx8qxp_ai_ml/ > > +F: include/configs/imx8qxp_ai_ml.h > > +F: configs/imx8qxp_ai_ml_defconfig > > diff --git a/board/einfochips/imx8qxp_ai_ml/Makefile > > b/board/einfochips/imx8qxp_ai_ml/Makefile new file mode 100644 > > index 0000000000..e08774dc6e > > --- /dev/null > > +++ b/board/einfochips/imx8qxp_ai_ml/Makefile > > @@ -0,0 +1,8 @@ > > +# > > +# Copyright 2019 Linaro Ltd. > > +# > > +# SPDX-License-Identifier: GPL-2.0+ > > +# > > + > > +obj-y += imx8qxp_ai_ml.o > > +obj-$(CONFIG_SPL_BUILD) += spl.o > > diff --git a/board/einfochips/imx8qxp_ai_ml/README > > b/board/einfochips/imx8qxp_ai_ml/README new file mode 100644 > > index 0000000000..488920580f > > --- /dev/null > > +++ b/board/einfochips/imx8qxp_ai_ml/README > > Thank you for preparing the README file, appreciated :-). > > > @@ -0,0 +1,49 @@ > > +U-Boot for the Einfochips i.MX8QXP AI_ML board > > + > > +Quick Start > > +=========== > > + > > +- Get and Build the ARM Trusted firmware > > +- Get scfw_tcm.bin and ahab-container.img > > +- Build U-Boot > > +- Flash the binary into the SD card > > +- Boot > > + > > +Get and Build the ARM Trusted firmware > > +====================================== > > + > > +$ git clone https://source.codeaurora.org/external/imx/imx-atf > > +$ cd imx-atf/ > > +$ git checkout origin/imx_4.9.88_imx8qxp_beta2 -b > > imx_4.9.88_imx8qxp_beta2 +$ make PLAT=imx8qxp bl31 > > + > > +Get scfw_tcm.bin and ahab-container.img > > +======================================= > > + > > +$ wget > > https://raw.githubusercontent.com/96boards-ai-ml/binaries/master/mx8qx-aiml-scfw-tcm.bin > > +$ wget > > https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.1.bin +$ > > chmod +x firmware-imx-8.1.bin +$ ./firmware-imx-8.1.bin + > > +Copy the following binaries to U-Boot folder: > > + > > +$ cp imx-atf/build/imx8qxp/release/bl31.bin . > > +$ cp firmware-imx-8.1/firmware/seco/mx8qx-ahab-container.img . > > + > > +Build U-Boot > > +============ > > + > > +$ make imx8qxp_ai_ml_defconfig > > +$ make u-boot-dtb.imx > > + > > +Flash the binary into the SD card > > +================================= > > + > > +Burn the u-boot-dtb.imx binary to SD card offset 32KB: > > + > > +$ sudo dd if=u-boot-dtb.imx of=/dev/sd[x] bs=1024 seek=32 > > + > > +Boot > > +==== > > + > > +Set Boot switch SW2: 1100. > > diff --git a/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c new file mode 100644 > > index 0000000000..e7632524a0 > > --- /dev/null > > +++ b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > @@ -0,0 +1,117 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Copyright 2018 NXP > > + * Copyright 2019 Linaro Ltd. > > + */ > > + > > +#include <common.h> > > +#include <errno.h> > > +#include <linux/libfdt.h> > > +#include <environment.h> > > +#include <fsl_esdhc.h> > > +#include <asm/io.h> > > +#include <asm/arch/clock.h> > > +#include <asm/arch/sci/sci.h> > > +#include <asm/arch/imx8-pins.h> > > +#include <asm/arch/iomux.h> > > +#include <asm/arch/sys_proto.h> > > + > > +DECLARE_GLOBAL_DATA_PTR; > > + > > +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << > > PADRING_CONFIG_SHIFT) | \ > > + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) > > | \ > > + (SC_PAD_28FDSOI_DSE_DV_HIGH << > > PADRING_DSE_SHIFT) | \ > > + (SC_PAD_28FDSOI_PS_PU << > > PADRING_PULL_SHIFT)) + > > +static iomux_cfg_t uart2_pads[] = { > > + SC_P_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL), > > + SC_P_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL), > > +}; > > As fair as I see - the uart could be configured via DTS (by using the > pinmux driver) as this is the U-Boot proper file. > Agree, this is not needed. > > + > > +static void setup_iomux_uart(void) > > +{ > > + imx8_iomux_setup_multiple_pads(uart2_pads, > > ARRAY_SIZE(uart2_pads)); +} > > + > > +int board_early_init_f(void) > > +{ > > + sc_pm_clock_rate_t rate = SC_80MHZ; > > + int ret; > > + > > + /* Set UART2 clock root to 80 MHz */ > > + ret = sc_pm_setup_uart(SC_R_UART_2, rate); > > + if (ret) > > + return ret; > > + > > + setup_iomux_uart(); > > + > > + return 0; > > +} > > + > > +#if IS_ENABLED(CONFIG_DM_GPIO) > > +static void board_gpio_init(void) > > +{ > > + /* TODO */ > > +} > > +#else > > +static inline void board_gpio_init(void) {} > > +#endif > > + > > I'm wondering if the above function is needed? > I thought about keeping this as I may add some gpio configurations in future. But, yeah I can remove it now and add once needed. > > +#if IS_ENABLED(CONFIG_FEC_MXC) > > +#include <miiphy.h> > > + > > +int board_phy_config(struct phy_device *phydev) > > +{ > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); > > + > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); > > + > > + if (phydev->drv->config) > > + phydev->drv->config(phydev); > > + > > + return 0; > > +} > > +#endif > > + > > +int checkboard(void) > > +{ > > + puts("Board: iMX8QXP AI_ML\n"); > > + > > + build_info(); > > + print_bootinfo(); > > + > > + return 0; > > +} > > + > > +int board_init(void) > > +{ > > + board_gpio_init(); > > + > > + return 0; > > +} > > Here you call the empty board_gpio_init(). > As per above comment, I'll remove it. > > + > > +/* Board specific reset that is system reset */ > > + > > +void reset_cpu(ulong addr) > > +{ > > + /* TODO */ > > +} > > Maybe you could use the SYSRESET driver from the outset? It internally > uses WDT for reset. > Hmm, looks like there is no watchdog driver for imx8qxp yet. > > + > > +#ifdef CONFIG_OF_BOARD_SETUP > > +int ft_board_setup(void *blob, bd_t *bd) > > +{ > > + return 0; > > +} > > +#endif > > + > > +int board_mmc_get_env_dev(int devno) > > +{ > > + return devno; > > +} > > This (the device and its instance) could be set in Kconfig. > Ack. > > + > > +int board_late_init(void) > > +{ > > + return 0; > > +} > > diff --git a/board/einfochips/imx8qxp_ai_ml/imximage.cfg > > b/board/einfochips/imx8qxp_ai_ml/imximage.cfg new file mode 100644 > > index 0000000000..4fc5ade313 > > --- /dev/null > > +++ b/board/einfochips/imx8qxp_ai_ml/imximage.cfg > > @@ -0,0 +1,24 @@ > > +/* SPDX-License-Identifier: GPL-2.0+ */ > > +/* > > + * Copyright 2018 NXP > > + * > > + * Refer doc/README.imx8image for more details about how-to configure > > + * and create imx8image boot image > > + */ > > + > > +#define __ASSEMBLY__ > > + > > +/* Boot from SD, sector size 0x400 */ > > +BOOT_FROM SD 0x400 > > +/* SoC type IMX8QX */ > > +SOC_TYPE IMX8QX > > +/* Append seco container image */ > > +APPEND mx8qx-ahab-container.img > > +/* Create the 2nd container */ > > +CONTAINER > > +/* Add scfw image with exec attribute */ > > +IMAGE SCU mx8qx-aiml-scfw-tcm.bin > > +/* Add ATF image with exec attribute */ > > +IMAGE A35 bl31.bin 0x80000000 > > +/* Add U-Boot image with load attribute */ > > +DATA A35 u-boot-dtb.bin 0x80020000 > > diff --git a/board/einfochips/imx8qxp_ai_ml/spl.c > > b/board/einfochips/imx8qxp_ai_ml/spl.c new file mode 100644 > > index 0000000000..63581eeaaf > > --- /dev/null > > +++ b/board/einfochips/imx8qxp_ai_ml/spl.c > > @@ -0,0 +1,49 @@ > > +/* > > + * Copyright 2018 NXP > > + * > > + * SPDX-License-Identifier: GPL-2.0+ > > + */ > > + > > +#include <common.h> > > +#include <dm.h> > > +#include <spl.h> > > +#include <dm/uclass.h> > > +#include <dm/device.h> > > +#include <dm/uclass-internal.h> > > +#include <dm/device-internal.h> > > +#include <dm/lists.h> > > + > > +DECLARE_GLOBAL_DATA_PTR; > > + > > +void spl_board_init(void) > > +{ > > + struct udevice *dev; > > + > > + uclass_find_first_device(UCLASS_MISC, &dev); > > + > > + for (; dev; uclass_find_next_device(&dev)) { > > + if (device_probe(dev)) > > + continue; > > + } > > What devices needs to be initialized in that way ? > Mostly SCU but it is not needed, so I'll remove it. > > + > > + arch_cpu_init(); > > + > > + board_early_init_f(); > > + > > + timer_init(); > > + > > + preloader_console_init(); > > + > > + puts("Normal Boot\n"); > > +} > > + > > +void board_init_f(ulong dummy) > > +{ > > + /* Clear global data */ > > + memset((void *)gd, 0, sizeof(gd_t)); > > + > > + /* Clear the BSS. */ > > + memset(__bss_start, 0, __bss_end - __bss_start); > > + > > + board_init_r(NULL, 0); > > +} > > diff --git a/configs/imx8qxp_ai_ml_defconfig > > b/configs/imx8qxp_ai_ml_defconfig new file mode 100644 > > index 0000000000..e20a0c783e > > --- /dev/null > > +++ b/configs/imx8qxp_ai_ml_defconfig > > @@ -0,0 +1,83 @@ > > +CONFIG_ARM=y > > +CONFIG_ARCH_IMX8=y > > +CONFIG_SYS_TEXT_BASE=0x80020000 > > +CONFIG_DISTRO_DEFAULTS=y > > +CONFIG_SPL_GPIO_SUPPORT=y > > +CONFIG_SPL_LIBCOMMON_SUPPORT=y > > +CONFIG_SPL_LIBGENERIC_SUPPORT=y > > +CONFIG_SYS_MALLOC_F_LEN=0x4000 > > +CONFIG_TARGET_IMX8QXP_AI_ML=y > > +CONFIG_SPL_MMC_SUPPORT=y > > +CONFIG_SPL_SERIAL_SUPPORT=y > > +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y > > +CONFIG_NR_DRAM_BANKS=4 > > +CONFIG_SPL=y > > +CONFIG_FIT=y > > +CONFIG_SPL_LOAD_FIT=y > > +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" > > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/einfochips/imx8qxp_ai_ml/imximage.cfg" > > +CONFIG_BOOTDELAY=3 > > +CONFIG_LOG=y > > +CONFIG_SPL_BOARD_INIT=y > > +CONFIG_SPL_SYS_MALLOC_SIMPLE=y > > +CONFIG_SPL_SEPARATE_BSS=y > > +CONFIG_SPL_POWER_SUPPORT=y > > +CONFIG_SPL_POWER_DOMAIN=y > > +CONFIG_SPL_WATCHDOG_SUPPORT=y > > +CONFIG_HUSH_PARSER=y > > +CONFIG_CMD_CPU=y > > +# CONFIG_CMD_IMPORTENV is not set > > +CONFIG_CMD_CLK=y > > +CONFIG_CMD_DM=y > > +CONFIG_CMD_FUSE=y > > +CONFIG_CMD_GPIO=y > > +CONFIG_CMD_GPT=y > > +CONFIG_CMD_I2C=y > > +CONFIG_CMD_MMC=y > > +CONFIG_CMD_DHCP=y > > +CONFIG_CMD_MII=y > > +CONFIG_CMD_PING=y > > +CONFIG_CMD_CACHE=y > > +CONFIG_CMD_EXT4=y > > +CONFIG_CMD_EXT4_WRITE=y > > +CONFIG_CMD_FAT=y > > +CONFIG_FAT_WRITE=y > > +CONFIG_CMD_FS_GENERIC=y > > +CONFIG_SPL_OF_CONTROL=y > > +CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qxp-ai_ml" > > +CONFIG_ENV_IS_IN_MMC=y > > +CONFIG_SPL_DM=y > > +CONFIG_SPL_CLK=y > > +CONFIG_CLK_IMX8=y > > +CONFIG_CPU=y > > +CONFIG_DM_GPIO=y > > +CONFIG_MXC_GPIO=y > > +CONFIG_DM_I2C=y > > +CONFIG_SYS_I2C_IMX_LPI2C=y > > +CONFIG_MISC=y > > +CONFIG_DM_MMC=y > > +CONFIG_FSL_ESDHC=y > > +CONFIG_PHYLIB=y > > +CONFIG_PHY_ADDR_ENABLE=y > > +CONFIG_PHY_ATHEROS=y > > +CONFIG_DM_ETH=y > > +CONFIG_NET_RANDOM_ETHADDR=y > > +CONFIG_PHY_GIGE=y > > +CONFIG_FEC_MXC_SHARE_MDIO=y > > +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000 > > +CONFIG_FEC_MXC=y > > +CONFIG_MII=y > > +CONFIG_PINCTRL=y > > +CONFIG_SPL_PINCTRL=y > > +CONFIG_PINCTRL_IMX8=y > > +CONFIG_POWER_DOMAIN=y > > +CONFIG_IMX8_POWER_DOMAIN=y > > +CONFIG_DM_REGULATOR=y > > +CONFIG_SPL_DM_REGULATOR=y > > +CONFIG_DM_REGULATOR_FIXED=y > > +CONFIG_DM_REGULATOR_GPIO=y > > +CONFIG_SPL_DM_REGULATOR_GPIO=y > > +CONFIG_DM_SERIAL=y > > +CONFIG_FSL_LPUART=y > > +CONFIG_SPL_TINY_MEMSET=y > > +# CONFIG_EFI_LOADER is not set > > diff --git a/include/configs/imx8qxp_ai_ml.h > > b/include/configs/imx8qxp_ai_ml.h new file mode 100644 > > index 0000000000..dd31189845 > > --- /dev/null > > +++ b/include/configs/imx8qxp_ai_ml.h > > @@ -0,0 +1,104 @@ > > +/* SPDX-License-Identifier: GPL-2.0+ */ > > +/* > > + * Copyright 2018 NXP > > + * Copyright 2019 Linaro Ltd. > > + */ > > + > > +#ifndef __IMX8QXP_AI_ML_H > > +#define __IMX8QXP_AI_ML_H > > + > > +#include <linux/sizes.h> > > +#include <asm/arch/imx-regs.h> > > + > > +#ifdef CONFIG_SPL_BUILD > > +#define CONFIG_SPL_MAX_SIZE (124 * > > 1024) +#define CONFIG_SYS_MONITOR_LEN > > (1024 * 1024) +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR > > +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x250 > > +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0 > > + > > +#define > > CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" > > +#define CONFIG_SPL_STACK 0x013E000 +#define > > CONFIG_SPL_BSS_START_ADDR 0x00128000 +#define > > CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */ > > +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000 +#define > > CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */ +#define > > CONFIG_SERIAL_LPUART_BASE 0x5a080000 +#define > > CONFIG_MALLOC_F_ADDR 0x00120000 + > > +#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE > > + > > +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE > > + > > +#define CONFIG_OF_EMBED > > I'm not sure if the OF_EMBED is not deprecated ... and replaced by > OF_SEPARATED. > I'm not sure about this. I don't see any such information. > > +#endif > > + > > +#define CONFIG_REMAKE_ELF > > + > > +#define CONFIG_BOARD_EARLY_INIT_F > > This could be set in Kconfig, IIRC > Ack. > > + > > +/* Flat Device Tree Definitions */ > > +#define CONFIG_OF_BOARD_SETUP > > + > > +#define CONFIG_FSL_USDHC > > + > > +#define CONFIG_ENV_OVERWRITE > > + > > +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG > > + > > +#define BOOT_TARGET_DEVICES(func) \ > > + func(MMC, mmc, 1) \ > > + func(DHCP, dhcp, na) > > + > > +#include <config_distro_bootcmd.h> > > +/* Initial environment variables */ > > +#define CONFIG_EXTRA_ENV_SETTINGS \ > > + "console=ttyLP2 earlycon\0" \ > > + "fdt_addr_r=0x83000000\0" \ > > + "kernel_addr_r=0x81000000\0" \ > > + "ramdisk_addr_r=0x94400000\0" \ > > + "scriptaddr=0x89000000\0" \ > > + "fdtfile=imx8qxp-ai_ml.dtb\0" \ > > + "fdt_high=0xffffffffffffffff\0" \ > > + "image=Image\0" \ > > + "initrd_addr=0x83800000\0" \ > > + "initrd_high=0xffffffffffffffff\0" \ > > + "netargs=setenv bootargs console=${console},${baudrate} " \ > > + "root=/dev/nfs ip=dhcp > > nfsroot=${serverip}:${nfsroot},v3,tcp" \ > > + "\0" \ > > + "nfsboot=run netargs; dhcp ${loadaddr} ${image}; tftp > > ${fdt_addr} " \ > > + "imx8qxp-ai_ml/${fdt_file}; booti ${loadaddr} - > > ${fdt_addr}\0" \ > > + BOOTENV > > + > > +/* Link Definitions */ > > +#define CONFIG_LOADADDR 0x80280000 > > + > > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR > > + > > +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000 > > + > > +/* Default environment is in SD */ > > +#define CONFIG_ENV_SIZE 0x1000 > > +#define CONFIG_ENV_OFFSET (64 * SZ_64K) > > + > > +/* USDHC2 is the SD card interface */ > > +#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */ > > +#define CONFIG_SYS_FSL_USDHC_NUM 2 > > + > > Some of those env setting defines as well as eMMC ones could be set now > in Kconfig. > Can you please specify those? I don't see these defines used in Kconfig. > > +/* Size of malloc() pool */ > > +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 > > * 1024)) * 1024) + > > +#define CONFIG_SYS_SDRAM_BASE 0x80000000 > > +#define PHYS_SDRAM_1 0x80000000 > > +#define PHYS_SDRAM_2 0x880000000 > > +#define PHYS_SDRAM_1_SIZE SZ_2G /* 2 > > Please fix this file globally, to use "SZ_XX" instead of magic numbers. > Ack. Thanks, Mani > > GB */ +#define PHYS_SDRAM_2_SIZE 0x00000000 /* > > 0 GB */ + > > +/* Generic Timer Definitions */ > > +#define COUNTER_FREQUENCY 8000000 /* 8MHz */ > > + > > +/* Networking */ > > +#define CONFIG_FEC_XCV_TYPE RGMII > > +#define FEC_QUIRK_ENET_MAC > > + > > +#endif /* __IMX8QXP_AI_ML_H */ > > > > > Best regards, > > Lukasz Majewski > > -- > > DENX Software Engineering GmbH, Managing Director: Wolfgang Denk > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany > Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de
Hi Manivannan, > Hi Lukasz, > > Thanks for the review! > > On Wed, Jul 24, 2019 at 10:07:13AM +0200, Lukasz Majewski wrote: > > Hi Manivannan, > > > > > This commit adds initial board support for iMX8QXP AI_ML board > > > from Einfochips. This board is one of the 96Boards Consumer > > > Edition and AI boards of the 96Boards family based on i.MX8QXP > > > SoC from NXP/Freescale. > > > > > > This initial supports contains following peripherals which are > > > tested and known to work: > > > > > > 1. Debug serial via UART2 > > > 2. SD card > > > 3. Ethernet > > > > > > More information about this board can be found in arrow website: > > > https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools > > > > > > Signed-off-by: Manivannan Sadhasivam > > > <manivannan.sadhasivam@linaro.org> --- > > > arch/arm/mach-imx/imx8/Kconfig | 6 + > > > board/einfochips/imx8qxp_ai_ml/Kconfig | 12 ++ > > > board/einfochips/imx8qxp_ai_ml/MAINTAINERS | 6 + > > > board/einfochips/imx8qxp_ai_ml/Makefile | 8 ++ > > > board/einfochips/imx8qxp_ai_ml/README | 49 ++++++++ > > > .../einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c | 117 > > > ++++++++++++++++++ board/einfochips/imx8qxp_ai_ml/imximage.cfg | > > > 24 ++++ board/einfochips/imx8qxp_ai_ml/spl.c | 49 > > > ++++++++ configs/imx8qxp_ai_ml_defconfig | 83 > > > +++++++++++++ include/configs/imx8qxp_ai_ml.h | 104 > > > ++++++++++++++++ 10 files changed, 458 insertions(+) > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/Kconfig > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/Makefile > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/README > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/imximage.cfg > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/spl.c > > > create mode 100644 configs/imx8qxp_ai_ml_defconfig > > > create mode 100644 include/configs/imx8qxp_ai_ml.h > > > > > > diff --git a/arch/arm/mach-imx/imx8/Kconfig > > > b/arch/arm/mach-imx/imx8/Kconfig index bbe323d5ca..cec21f8dd2 > > > 100644 --- a/arch/arm/mach-imx/imx8/Kconfig > > > +++ b/arch/arm/mach-imx/imx8/Kconfig > > > @@ -37,6 +37,11 @@ config TARGET_COLIBRI_IMX8X > > > select BOARD_LATE_INIT > > > select IMX8QXP > > > > > > +config TARGET_IMX8QXP_AI_ML > > > + bool "Support i.MX8QXP AI_ML board" > > > + select BOARD_LATE_INIT > > > + select IMX8QXP > > > + > > > config TARGET_IMX8QM_MEK > > > bool "Support i.MX8QM MEK board" > > > select BOARD_LATE_INIT > > > @@ -49,6 +54,7 @@ config TARGET_IMX8QXP_MEK > > > > > > endchoice > > > > > > +source "board/einfochips/imx8qxp_ai_ml/Kconfig" > > > source "board/freescale/imx8qm_mek/Kconfig" > > > source "board/freescale/imx8qxp_mek/Kconfig" > > > source "board/toradex/apalis-imx8/Kconfig" > > > diff --git a/board/einfochips/imx8qxp_ai_ml/Kconfig > > > b/board/einfochips/imx8qxp_ai_ml/Kconfig new file mode 100644 > > > index 0000000000..697a831013 > > > --- /dev/null > > > +++ b/board/einfochips/imx8qxp_ai_ml/Kconfig > > > @@ -0,0 +1,12 @@ > > > +if TARGET_IMX8QXP_AI_ML > > > + > > > +config SYS_BOARD > > > + default "imx8qxp_ai_ml" > > > + > > > +config SYS_VENDOR > > > + default "einfochips" > > > + > > > +config SYS_CONFIG_NAME > > > + default "imx8qxp_ai_ml" > > > + > > > +endif > > > diff --git a/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > > b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS new file mode 100644 > > > index 0000000000..add0bd9431 > > > --- /dev/null > > > +++ b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > > @@ -0,0 +1,6 @@ > > > +i.MX8QXP AI_ML BOARD > > > +M: Manivannan Sadhasivam > > > <manivannan.sadhasivam@linaro.org> +S: Maintained > > > +F: board/einfochips/imx8qxp_ai_ml/ > > > +F: include/configs/imx8qxp_ai_ml.h > > > +F: configs/imx8qxp_ai_ml_defconfig > > > diff --git a/board/einfochips/imx8qxp_ai_ml/Makefile > > > b/board/einfochips/imx8qxp_ai_ml/Makefile new file mode 100644 > > > index 0000000000..e08774dc6e > > > --- /dev/null > > > +++ b/board/einfochips/imx8qxp_ai_ml/Makefile > > > @@ -0,0 +1,8 @@ > > > +# > > > +# Copyright 2019 Linaro Ltd. > > > +# > > > +# SPDX-License-Identifier: GPL-2.0+ > > > +# > > > + > > > +obj-y += imx8qxp_ai_ml.o > > > +obj-$(CONFIG_SPL_BUILD) += spl.o > > > diff --git a/board/einfochips/imx8qxp_ai_ml/README > > > b/board/einfochips/imx8qxp_ai_ml/README new file mode 100644 > > > index 0000000000..488920580f > > > --- /dev/null > > > +++ b/board/einfochips/imx8qxp_ai_ml/README > > > > Thank you for preparing the README file, appreciated :-). > > > > > @@ -0,0 +1,49 @@ > > > +U-Boot for the Einfochips i.MX8QXP AI_ML board > > > + > > > +Quick Start > > > +=========== > > > + > > > +- Get and Build the ARM Trusted firmware > > > +- Get scfw_tcm.bin and ahab-container.img > > > +- Build U-Boot > > > +- Flash the binary into the SD card > > > +- Boot > > > + > > > +Get and Build the ARM Trusted firmware > > > +====================================== > > > + > > > +$ git clone https://source.codeaurora.org/external/imx/imx-atf > > > +$ cd imx-atf/ > > > +$ git checkout origin/imx_4.9.88_imx8qxp_beta2 -b > > > imx_4.9.88_imx8qxp_beta2 +$ make PLAT=imx8qxp bl31 > > > + > > > +Get scfw_tcm.bin and ahab-container.img > > > +======================================= > > > + > > > +$ wget > > > https://raw.githubusercontent.com/96boards-ai-ml/binaries/master/mx8qx-aiml-scfw-tcm.bin > > > +$ wget > > > https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.1.bin +$ > > > chmod +x firmware-imx-8.1.bin +$ ./firmware-imx-8.1.bin + > > > +Copy the following binaries to U-Boot folder: > > > + > > > +$ cp imx-atf/build/imx8qxp/release/bl31.bin . > > > +$ cp firmware-imx-8.1/firmware/seco/mx8qx-ahab-container.img . > > > + > > > +Build U-Boot > > > +============ > > > + > > > +$ make imx8qxp_ai_ml_defconfig > > > +$ make u-boot-dtb.imx > > > + > > > +Flash the binary into the SD card > > > +================================= > > > + > > > +Burn the u-boot-dtb.imx binary to SD card offset 32KB: > > > + > > > +$ sudo dd if=u-boot-dtb.imx of=/dev/sd[x] bs=1024 seek=32 > > > + > > > +Boot > > > +==== > > > + > > > +Set Boot switch SW2: 1100. > > > diff --git a/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > > b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c new file mode > > > 100644 index 0000000000..e7632524a0 > > > --- /dev/null > > > +++ b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > > @@ -0,0 +1,117 @@ > > > +// SPDX-License-Identifier: GPL-2.0+ > > > +/* > > > + * Copyright 2018 NXP > > > + * Copyright 2019 Linaro Ltd. > > > + */ > > > + > > > +#include <common.h> > > > +#include <errno.h> > > > +#include <linux/libfdt.h> > > > +#include <environment.h> > > > +#include <fsl_esdhc.h> > > > +#include <asm/io.h> > > > +#include <asm/arch/clock.h> > > > +#include <asm/arch/sci/sci.h> > > > +#include <asm/arch/imx8-pins.h> > > > +#include <asm/arch/iomux.h> > > > +#include <asm/arch/sys_proto.h> > > > + > > > +DECLARE_GLOBAL_DATA_PTR; > > > + > > > +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << > > > PADRING_CONFIG_SHIFT) | \ > > > + (SC_PAD_ISO_OFF << > > > PADRING_LPCONFIG_SHIFT) | \ > > > + (SC_PAD_28FDSOI_DSE_DV_HIGH << > > > PADRING_DSE_SHIFT) | \ > > > + (SC_PAD_28FDSOI_PS_PU << > > > PADRING_PULL_SHIFT)) + > > > +static iomux_cfg_t uart2_pads[] = { > > > + SC_P_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL), > > > + SC_P_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL), > > > +}; > > > > As fair as I see - the uart could be configured via DTS (by using > > the pinmux driver) as this is the U-Boot proper file. > > > > Agree, this is not needed. > > > > + > > > +static void setup_iomux_uart(void) > > > +{ > > > + imx8_iomux_setup_multiple_pads(uart2_pads, > > > ARRAY_SIZE(uart2_pads)); +} > > > + > > > +int board_early_init_f(void) > > > +{ > > > + sc_pm_clock_rate_t rate = SC_80MHZ; > > > + int ret; > > > + > > > + /* Set UART2 clock root to 80 MHz */ > > > + ret = sc_pm_setup_uart(SC_R_UART_2, rate); > > > + if (ret) > > > + return ret; > > > + > > > + setup_iomux_uart(); > > > + > > > + return 0; > > > +} > > > + > > > +#if IS_ENABLED(CONFIG_DM_GPIO) > > > +static void board_gpio_init(void) > > > +{ > > > + /* TODO */ > > > +} > > > +#else > > > +static inline void board_gpio_init(void) {} > > > +#endif > > > + > > > > I'm wondering if the above function is needed? > > > > I thought about keeping this as I may add some gpio configurations > in future. But, yeah I can remove it now and add once needed. The general rule is to avoid adding any dead (i.e. not used) code to the main line. The practical reason for it is to have the code base as small as possible. Moreover, the patch, which adds this board is rather large, so in that way we make it smaller. This code shall be added when you introduce the GPIO needed for this board. > > > > +#if IS_ENABLED(CONFIG_FEC_MXC) > > > +#include <miiphy.h> > > > + > > > +int board_phy_config(struct phy_device *phydev) > > > +{ > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); > > > + > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); > > > + > > > + if (phydev->drv->config) > > > + phydev->drv->config(phydev); > > > + > > > + return 0; > > > +} > > > +#endif > > > + > > > +int checkboard(void) > > > +{ > > > + puts("Board: iMX8QXP AI_ML\n"); > > > + > > > + build_info(); > > > + print_bootinfo(); > > > + > > > + return 0; > > > +} > > > + > > > +int board_init(void) > > > +{ > > > + board_gpio_init(); > > > + > > > + return 0; > > > +} > > > > Here you call the empty board_gpio_init(). > > > > As per above comment, I'll remove it. > > > > + > > > +/* Board specific reset that is system reset */ > > > + > > > +void reset_cpu(ulong addr) > > > +{ > > > + /* TODO */ > > > +} > > > > Maybe you could use the SYSRESET driver from the outset? It > > internally uses WDT for reset. > > > > Hmm, looks like there is no watchdog driver for imx8qxp yet. If I may ask - how do you plan to reset the board? On most i.MX boards the reset is done by triggering the WDT. > > > > + > > > +#ifdef CONFIG_OF_BOARD_SETUP > > > +int ft_board_setup(void *blob, bd_t *bd) > > > +{ > > > + return 0; > > > +} > > > +#endif > > > + > > > +int board_mmc_get_env_dev(int devno) > > > +{ > > > + return devno; > > > +} > > > > This (the device and its instance) could be set in Kconfig. > > > > Ack. > > > > + > > > +int board_late_init(void) > > > +{ > > > + return 0; > > > +} > > > diff --git a/board/einfochips/imx8qxp_ai_ml/imximage.cfg > > > b/board/einfochips/imx8qxp_ai_ml/imximage.cfg new file mode 100644 > > > index 0000000000..4fc5ade313 > > > --- /dev/null > > > +++ b/board/einfochips/imx8qxp_ai_ml/imximage.cfg > > > @@ -0,0 +1,24 @@ > > > +/* SPDX-License-Identifier: GPL-2.0+ */ > > > +/* > > > + * Copyright 2018 NXP > > > + * > > > + * Refer doc/README.imx8image for more details about how-to > > > configure > > > + * and create imx8image boot image > > > + */ > > > + > > > +#define __ASSEMBLY__ > > > + > > > +/* Boot from SD, sector size 0x400 */ > > > +BOOT_FROM SD 0x400 > > > +/* SoC type IMX8QX */ > > > +SOC_TYPE IMX8QX > > > +/* Append seco container image */ > > > +APPEND mx8qx-ahab-container.img > > > +/* Create the 2nd container */ > > > +CONTAINER > > > +/* Add scfw image with exec attribute */ > > > +IMAGE SCU mx8qx-aiml-scfw-tcm.bin > > > +/* Add ATF image with exec attribute */ > > > +IMAGE A35 bl31.bin 0x80000000 > > > +/* Add U-Boot image with load attribute */ > > > +DATA A35 u-boot-dtb.bin 0x80020000 > > > diff --git a/board/einfochips/imx8qxp_ai_ml/spl.c > > > b/board/einfochips/imx8qxp_ai_ml/spl.c new file mode 100644 > > > index 0000000000..63581eeaaf > > > --- /dev/null > > > +++ b/board/einfochips/imx8qxp_ai_ml/spl.c > > > @@ -0,0 +1,49 @@ > > > +/* > > > + * Copyright 2018 NXP > > > + * > > > + * SPDX-License-Identifier: GPL-2.0+ > > > + */ > > > + > > > +#include <common.h> > > > +#include <dm.h> > > > +#include <spl.h> > > > +#include <dm/uclass.h> > > > +#include <dm/device.h> > > > +#include <dm/uclass-internal.h> > > > +#include <dm/device-internal.h> > > > +#include <dm/lists.h> > > > + > > > +DECLARE_GLOBAL_DATA_PTR; > > > + > > > +void spl_board_init(void) > > > +{ > > > + struct udevice *dev; > > > + > > > + uclass_find_first_device(UCLASS_MISC, &dev); > > > + > > > + for (; dev; uclass_find_next_device(&dev)) { > > > + if (device_probe(dev)) > > > + continue; > > > + } > > > > What devices needs to be initialized in that way ? > > > > Mostly SCU but it is not needed, so I'll remove it. Ok. > > > > + > > > + arch_cpu_init(); > > > + > > > + board_early_init_f(); > > > + > > > + timer_init(); > > > + > > > + preloader_console_init(); > > > + > > > + puts("Normal Boot\n"); > > > +} > > > + > > > +void board_init_f(ulong dummy) > > > +{ > > > + /* Clear global data */ > > > + memset((void *)gd, 0, sizeof(gd_t)); > > > + > > > + /* Clear the BSS. */ > > > + memset(__bss_start, 0, __bss_end - __bss_start); > > > + > > > + board_init_r(NULL, 0); > > > +} > > > diff --git a/configs/imx8qxp_ai_ml_defconfig > > > b/configs/imx8qxp_ai_ml_defconfig new file mode 100644 > > > index 0000000000..e20a0c783e > > > --- /dev/null > > > +++ b/configs/imx8qxp_ai_ml_defconfig > > > @@ -0,0 +1,83 @@ > > > +CONFIG_ARM=y > > > +CONFIG_ARCH_IMX8=y > > > +CONFIG_SYS_TEXT_BASE=0x80020000 > > > +CONFIG_DISTRO_DEFAULTS=y > > > +CONFIG_SPL_GPIO_SUPPORT=y > > > +CONFIG_SPL_LIBCOMMON_SUPPORT=y > > > +CONFIG_SPL_LIBGENERIC_SUPPORT=y > > > +CONFIG_SYS_MALLOC_F_LEN=0x4000 > > > +CONFIG_TARGET_IMX8QXP_AI_ML=y > > > +CONFIG_SPL_MMC_SUPPORT=y > > > +CONFIG_SPL_SERIAL_SUPPORT=y > > > +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y > > > +CONFIG_NR_DRAM_BANKS=4 > > > +CONFIG_SPL=y > > > +CONFIG_FIT=y > > > +CONFIG_SPL_LOAD_FIT=y > > > +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" > > > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/einfochips/imx8qxp_ai_ml/imximage.cfg" > > > +CONFIG_BOOTDELAY=3 > > > +CONFIG_LOG=y > > > +CONFIG_SPL_BOARD_INIT=y > > > +CONFIG_SPL_SYS_MALLOC_SIMPLE=y > > > +CONFIG_SPL_SEPARATE_BSS=y > > > +CONFIG_SPL_POWER_SUPPORT=y > > > +CONFIG_SPL_POWER_DOMAIN=y > > > +CONFIG_SPL_WATCHDOG_SUPPORT=y > > > +CONFIG_HUSH_PARSER=y > > > +CONFIG_CMD_CPU=y > > > +# CONFIG_CMD_IMPORTENV is not set > > > +CONFIG_CMD_CLK=y > > > +CONFIG_CMD_DM=y > > > +CONFIG_CMD_FUSE=y > > > +CONFIG_CMD_GPIO=y > > > +CONFIG_CMD_GPT=y > > > +CONFIG_CMD_I2C=y > > > +CONFIG_CMD_MMC=y > > > +CONFIG_CMD_DHCP=y > > > +CONFIG_CMD_MII=y > > > +CONFIG_CMD_PING=y > > > +CONFIG_CMD_CACHE=y > > > +CONFIG_CMD_EXT4=y > > > +CONFIG_CMD_EXT4_WRITE=y > > > +CONFIG_CMD_FAT=y > > > +CONFIG_FAT_WRITE=y > > > +CONFIG_CMD_FS_GENERIC=y > > > +CONFIG_SPL_OF_CONTROL=y > > > +CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qxp-ai_ml" > > > +CONFIG_ENV_IS_IN_MMC=y > > > +CONFIG_SPL_DM=y > > > +CONFIG_SPL_CLK=y > > > +CONFIG_CLK_IMX8=y > > > +CONFIG_CPU=y > > > +CONFIG_DM_GPIO=y > > > +CONFIG_MXC_GPIO=y > > > +CONFIG_DM_I2C=y > > > +CONFIG_SYS_I2C_IMX_LPI2C=y > > > +CONFIG_MISC=y > > > +CONFIG_DM_MMC=y > > > +CONFIG_FSL_ESDHC=y > > > +CONFIG_PHYLIB=y > > > +CONFIG_PHY_ADDR_ENABLE=y > > > +CONFIG_PHY_ATHEROS=y > > > +CONFIG_DM_ETH=y > > > +CONFIG_NET_RANDOM_ETHADDR=y > > > +CONFIG_PHY_GIGE=y > > > +CONFIG_FEC_MXC_SHARE_MDIO=y > > > +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000 > > > +CONFIG_FEC_MXC=y > > > +CONFIG_MII=y > > > +CONFIG_PINCTRL=y > > > +CONFIG_SPL_PINCTRL=y > > > +CONFIG_PINCTRL_IMX8=y > > > +CONFIG_POWER_DOMAIN=y > > > +CONFIG_IMX8_POWER_DOMAIN=y > > > +CONFIG_DM_REGULATOR=y > > > +CONFIG_SPL_DM_REGULATOR=y > > > +CONFIG_DM_REGULATOR_FIXED=y > > > +CONFIG_DM_REGULATOR_GPIO=y > > > +CONFIG_SPL_DM_REGULATOR_GPIO=y > > > +CONFIG_DM_SERIAL=y > > > +CONFIG_FSL_LPUART=y > > > +CONFIG_SPL_TINY_MEMSET=y > > > +# CONFIG_EFI_LOADER is not set > > > diff --git a/include/configs/imx8qxp_ai_ml.h > > > b/include/configs/imx8qxp_ai_ml.h new file mode 100644 > > > index 0000000000..dd31189845 > > > --- /dev/null > > > +++ b/include/configs/imx8qxp_ai_ml.h > > > @@ -0,0 +1,104 @@ > > > +/* SPDX-License-Identifier: GPL-2.0+ */ > > > +/* > > > + * Copyright 2018 NXP > > > + * Copyright 2019 Linaro Ltd. > > > + */ > > > + > > > +#ifndef __IMX8QXP_AI_ML_H > > > +#define __IMX8QXP_AI_ML_H > > > + > > > +#include <linux/sizes.h> > > > +#include <asm/arch/imx-regs.h> > > > + > > > +#ifdef CONFIG_SPL_BUILD > > > +#define CONFIG_SPL_MAX_SIZE (124 * > > > 1024) +#define CONFIG_SYS_MONITOR_LEN > > > (1024 * 1024) +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR > > > +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR > > > 0x250 +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0 > > > + > > > +#define > > > CONFIG_SPL_LDSCRIPT > > > "arch/arm/cpu/armv8/u-boot-spl.lds" +#define > > > CONFIG_SPL_STACK 0x013E000 +#define > > > CONFIG_SPL_BSS_START_ADDR 0x00128000 +#define > > > CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */ > > > +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000 +#define > > > CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */ > > > +#define CONFIG_SERIAL_LPUART_BASE 0x5a080000 +#define > > > CONFIG_MALLOC_F_ADDR 0x00120000 + +#define > > > CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE + > > > +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE > > > + > > > +#define CONFIG_OF_EMBED > > > > I'm not sure if the OF_EMBED is not deprecated ... and replaced by > > OF_SEPARATED. > > > > I'm not sure about this. I don't see any such information. There was a u-boot ML discussion about OF_EMBED deprecation. https://patchwork.ozlabs.org/project/uboot/list/?series=&submitter=&state=*&q=OF_EMBED&archive=both&delegate= Also please see: https://www.chromium.org/developers/u-boot > > > > +#endif > > > + > > > +#define CONFIG_REMAKE_ELF > > > + > > > +#define CONFIG_BOARD_EARLY_INIT_F > > > > This could be set in Kconfig, IIRC > > > > Ack. > > > > + > > > +/* Flat Device Tree Definitions */ > > > +#define CONFIG_OF_BOARD_SETUP > > > + > > > +#define CONFIG_FSL_USDHC > > > + > > > +#define CONFIG_ENV_OVERWRITE > > > + > > > +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG > > > + > > > +#define BOOT_TARGET_DEVICES(func) \ > > > + func(MMC, mmc, 1) \ > > > + func(DHCP, dhcp, na) > > > + > > > +#include <config_distro_bootcmd.h> > > > +/* Initial environment variables */ > > > +#define CONFIG_EXTRA_ENV_SETTINGS > > > \ > > > + "console=ttyLP2 earlycon\0" \ > > > + "fdt_addr_r=0x83000000\0" \ > > > + "kernel_addr_r=0x81000000\0" \ > > > + "ramdisk_addr_r=0x94400000\0" \ > > > + "scriptaddr=0x89000000\0" \ > > > + "fdtfile=imx8qxp-ai_ml.dtb\0" \ > > > + "fdt_high=0xffffffffffffffff\0" \ > > > + "image=Image\0" \ > > > + "initrd_addr=0x83800000\0" \ > > > + "initrd_high=0xffffffffffffffff\0" \ > > > + "netargs=setenv bootargs console=${console},${baudrate} > > > " \ > > > + "root=/dev/nfs ip=dhcp > > > nfsroot=${serverip}:${nfsroot},v3,tcp" \ > > > + "\0" \ > > > + "nfsboot=run netargs; dhcp ${loadaddr} ${image}; tftp > > > ${fdt_addr} " \ > > > + "imx8qxp-ai_ml/${fdt_file}; booti ${loadaddr} - > > > ${fdt_addr}\0" \ > > > + BOOTENV > > > + > > > +/* Link Definitions */ > > > +#define CONFIG_LOADADDR 0x80280000 > > > + > > > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR > > > + > > > +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000 > > > + > > > +/* Default environment is in SD */ > > > +#define CONFIG_ENV_SIZE 0x1000 > > > +#define CONFIG_ENV_OFFSET (64 * SZ_64K) > > > + > > > +/* USDHC2 is the SD card interface */ > > > +#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */ > > > +#define CONFIG_SYS_FSL_USDHC_NUM 2 > > > + > > > > Some of those env setting defines as well as eMMC ones could be set > > now in Kconfig. > > > > Can you please specify those? I don't see these defines used in > Kconfig. The best (and simplest) way is to just check if the corresponding CONFIG_* option is already moved (ported) to Kconfig. For example ENV_SIZE and ENV_OFFSET are. > > > > +/* Size of malloc() pool */ > > > +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + > > > (32 > > > * 1024)) * 1024) + > > > +#define CONFIG_SYS_SDRAM_BASE 0x80000000 > > > +#define PHYS_SDRAM_1 0x80000000 > > > +#define PHYS_SDRAM_2 0x880000000 > > > +#define PHYS_SDRAM_1_SIZE SZ_2G /* > > > 2 > > > > Please fix this file globally, to use "SZ_XX" instead of magic > > numbers. > > Ack. > > Thanks, > Mani > > > > GB */ +#define PHYS_SDRAM_2_SIZE 0x00000000 > > > /* 0 GB */ + > > > +/* Generic Timer Definitions */ > > > +#define COUNTER_FREQUENCY 8000000 /* 8MHz > > > */ + > > > +/* Networking */ > > > +#define CONFIG_FEC_XCV_TYPE RGMII > > > +#define FEC_QUIRK_ENET_MAC > > > + > > > +#endif /* __IMX8QXP_AI_ML_H */ > > > > > > > > > > Best regards, > > > > Lukasz Majewski > > > > -- > > > > DENX Software Engineering GmbH, Managing Director: Wolfgang > > Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, > > Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: > > lukma@denx.de > > Best regards, Lukasz Majewski -- DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de
Hi Lukasz, On Thu, Aug 15, 2019 at 09:51:25AM +0200, Lukasz Majewski wrote: > Hi Manivannan, > > > Hi Lukasz, > > > > Thanks for the review! > > > > On Wed, Jul 24, 2019 at 10:07:13AM +0200, Lukasz Majewski wrote: > > > Hi Manivannan, > > > > > > > This commit adds initial board support for iMX8QXP AI_ML board > > > > from Einfochips. This board is one of the 96Boards Consumer > > > > Edition and AI boards of the 96Boards family based on i.MX8QXP > > > > SoC from NXP/Freescale. > > > > > > > > This initial supports contains following peripherals which are > > > > tested and known to work: > > > > > > > > 1. Debug serial via UART2 > > > > 2. SD card > > > > 3. Ethernet > > > > > > > > More information about this board can be found in arrow website: > > > > https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools > > > > > > > > Signed-off-by: Manivannan Sadhasivam > > > > <manivannan.sadhasivam@linaro.org> --- > > > > arch/arm/mach-imx/imx8/Kconfig | 6 + > > > > board/einfochips/imx8qxp_ai_ml/Kconfig | 12 ++ > > > > board/einfochips/imx8qxp_ai_ml/MAINTAINERS | 6 + > > > > board/einfochips/imx8qxp_ai_ml/Makefile | 8 ++ > > > > board/einfochips/imx8qxp_ai_ml/README | 49 ++++++++ > > > > .../einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c | 117 > > > > ++++++++++++++++++ board/einfochips/imx8qxp_ai_ml/imximage.cfg | > > > > 24 ++++ board/einfochips/imx8qxp_ai_ml/spl.c | 49 > > > > ++++++++ configs/imx8qxp_ai_ml_defconfig | 83 > > > > +++++++++++++ include/configs/imx8qxp_ai_ml.h | 104 > > > > ++++++++++++++++ 10 files changed, 458 insertions(+) > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/Kconfig > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/Makefile > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/README > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/imximage.cfg > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/spl.c > > > > create mode 100644 configs/imx8qxp_ai_ml_defconfig > > > > create mode 100644 include/configs/imx8qxp_ai_ml.h > > > > > > > > diff --git a/arch/arm/mach-imx/imx8/Kconfig > > > > b/arch/arm/mach-imx/imx8/Kconfig index bbe323d5ca..cec21f8dd2 > > > > 100644 --- a/arch/arm/mach-imx/imx8/Kconfig > > > > +++ b/arch/arm/mach-imx/imx8/Kconfig > > > > @@ -37,6 +37,11 @@ config TARGET_COLIBRI_IMX8X > > > > select BOARD_LATE_INIT > > > > select IMX8QXP > > > > > > > > +config TARGET_IMX8QXP_AI_ML > > > > + bool "Support i.MX8QXP AI_ML board" > > > > + select BOARD_LATE_INIT > > > > + select IMX8QXP > > > > + > > > > config TARGET_IMX8QM_MEK > > > > bool "Support i.MX8QM MEK board" > > > > select BOARD_LATE_INIT > > > > @@ -49,6 +54,7 @@ config TARGET_IMX8QXP_MEK > > > > > > > > endchoice > > > > > > > > +source "board/einfochips/imx8qxp_ai_ml/Kconfig" > > > > source "board/freescale/imx8qm_mek/Kconfig" > > > > source "board/freescale/imx8qxp_mek/Kconfig" > > > > source "board/toradex/apalis-imx8/Kconfig" > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/Kconfig > > > > b/board/einfochips/imx8qxp_ai_ml/Kconfig new file mode 100644 > > > > index 0000000000..697a831013 > > > > --- /dev/null > > > > +++ b/board/einfochips/imx8qxp_ai_ml/Kconfig > > > > @@ -0,0 +1,12 @@ > > > > +if TARGET_IMX8QXP_AI_ML > > > > + > > > > +config SYS_BOARD > > > > + default "imx8qxp_ai_ml" > > > > + > > > > +config SYS_VENDOR > > > > + default "einfochips" > > > > + > > > > +config SYS_CONFIG_NAME > > > > + default "imx8qxp_ai_ml" > > > > + > > > > +endif > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > > > b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS new file mode 100644 > > > > index 0000000000..add0bd9431 > > > > --- /dev/null > > > > +++ b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > > > @@ -0,0 +1,6 @@ > > > > +i.MX8QXP AI_ML BOARD > > > > +M: Manivannan Sadhasivam > > > > <manivannan.sadhasivam@linaro.org> +S: Maintained > > > > +F: board/einfochips/imx8qxp_ai_ml/ > > > > +F: include/configs/imx8qxp_ai_ml.h > > > > +F: configs/imx8qxp_ai_ml_defconfig > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/Makefile > > > > b/board/einfochips/imx8qxp_ai_ml/Makefile new file mode 100644 > > > > index 0000000000..e08774dc6e > > > > --- /dev/null > > > > +++ b/board/einfochips/imx8qxp_ai_ml/Makefile > > > > @@ -0,0 +1,8 @@ > > > > +# > > > > +# Copyright 2019 Linaro Ltd. > > > > +# > > > > +# SPDX-License-Identifier: GPL-2.0+ > > > > +# > > > > + > > > > +obj-y += imx8qxp_ai_ml.o > > > > +obj-$(CONFIG_SPL_BUILD) += spl.o > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/README > > > > b/board/einfochips/imx8qxp_ai_ml/README new file mode 100644 > > > > index 0000000000..488920580f > > > > --- /dev/null > > > > +++ b/board/einfochips/imx8qxp_ai_ml/README > > > > > > Thank you for preparing the README file, appreciated :-). > > > > > > > @@ -0,0 +1,49 @@ > > > > +U-Boot for the Einfochips i.MX8QXP AI_ML board > > > > + > > > > +Quick Start > > > > +=========== > > > > + > > > > +- Get and Build the ARM Trusted firmware > > > > +- Get scfw_tcm.bin and ahab-container.img > > > > +- Build U-Boot > > > > +- Flash the binary into the SD card > > > > +- Boot > > > > + > > > > +Get and Build the ARM Trusted firmware > > > > +====================================== > > > > + > > > > +$ git clone https://source.codeaurora.org/external/imx/imx-atf > > > > +$ cd imx-atf/ > > > > +$ git checkout origin/imx_4.9.88_imx8qxp_beta2 -b > > > > imx_4.9.88_imx8qxp_beta2 +$ make PLAT=imx8qxp bl31 > > > > + > > > > +Get scfw_tcm.bin and ahab-container.img > > > > +======================================= > > > > + > > > > +$ wget > > > > https://raw.githubusercontent.com/96boards-ai-ml/binaries/master/mx8qx-aiml-scfw-tcm.bin > > > > +$ wget > > > > https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.1.bin +$ > > > > chmod +x firmware-imx-8.1.bin +$ ./firmware-imx-8.1.bin + > > > > +Copy the following binaries to U-Boot folder: > > > > + > > > > +$ cp imx-atf/build/imx8qxp/release/bl31.bin . > > > > +$ cp firmware-imx-8.1/firmware/seco/mx8qx-ahab-container.img . > > > > + > > > > +Build U-Boot > > > > +============ > > > > + > > > > +$ make imx8qxp_ai_ml_defconfig > > > > +$ make u-boot-dtb.imx > > > > + > > > > +Flash the binary into the SD card > > > > +================================= > > > > + > > > > +Burn the u-boot-dtb.imx binary to SD card offset 32KB: > > > > + > > > > +$ sudo dd if=u-boot-dtb.imx of=/dev/sd[x] bs=1024 seek=32 > > > > + > > > > +Boot > > > > +==== > > > > + > > > > +Set Boot switch SW2: 1100. > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > > > b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c new file mode > > > > 100644 index 0000000000..e7632524a0 > > > > --- /dev/null > > > > +++ b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > > > @@ -0,0 +1,117 @@ > > > > +// SPDX-License-Identifier: GPL-2.0+ > > > > +/* > > > > + * Copyright 2018 NXP > > > > + * Copyright 2019 Linaro Ltd. > > > > + */ > > > > + > > > > +#include <common.h> > > > > +#include <errno.h> > > > > +#include <linux/libfdt.h> > > > > +#include <environment.h> > > > > +#include <fsl_esdhc.h> > > > > +#include <asm/io.h> > > > > +#include <asm/arch/clock.h> > > > > +#include <asm/arch/sci/sci.h> > > > > +#include <asm/arch/imx8-pins.h> > > > > +#include <asm/arch/iomux.h> > > > > +#include <asm/arch/sys_proto.h> > > > > + > > > > +DECLARE_GLOBAL_DATA_PTR; > > > > + > > > > +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << > > > > PADRING_CONFIG_SHIFT) | \ > > > > + (SC_PAD_ISO_OFF << > > > > PADRING_LPCONFIG_SHIFT) | \ > > > > + (SC_PAD_28FDSOI_DSE_DV_HIGH << > > > > PADRING_DSE_SHIFT) | \ > > > > + (SC_PAD_28FDSOI_PS_PU << > > > > PADRING_PULL_SHIFT)) + > > > > +static iomux_cfg_t uart2_pads[] = { > > > > + SC_P_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL), > > > > + SC_P_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL), > > > > +}; > > > > > > As fair as I see - the uart could be configured via DTS (by using > > > the pinmux driver) as this is the U-Boot proper file. > > > > > > > Agree, this is not needed. > > > > > > + > > > > +static void setup_iomux_uart(void) > > > > +{ > > > > + imx8_iomux_setup_multiple_pads(uart2_pads, > > > > ARRAY_SIZE(uart2_pads)); +} > > > > + > > > > +int board_early_init_f(void) > > > > +{ > > > > + sc_pm_clock_rate_t rate = SC_80MHZ; > > > > + int ret; > > > > + > > > > + /* Set UART2 clock root to 80 MHz */ > > > > + ret = sc_pm_setup_uart(SC_R_UART_2, rate); > > > > + if (ret) > > > > + return ret; > > > > + > > > > + setup_iomux_uart(); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +#if IS_ENABLED(CONFIG_DM_GPIO) > > > > +static void board_gpio_init(void) > > > > +{ > > > > + /* TODO */ > > > > +} > > > > +#else > > > > +static inline void board_gpio_init(void) {} > > > > +#endif > > > > + > > > > > > I'm wondering if the above function is needed? > > > > > > > I thought about keeping this as I may add some gpio configurations > > in future. But, yeah I can remove it now and add once needed. > > The general rule is to avoid adding any dead (i.e. not used) code to > the main line. > > The practical reason for it is to have the code base as small as > possible. Moreover, the patch, which adds this board is rather large, > so in that way we make it smaller. > > This code shall be added when you introduce the GPIO needed for this > board. > Okay, thanks for the info! > > > > > > +#if IS_ENABLED(CONFIG_FEC_MXC) > > > > +#include <miiphy.h> > > > > + > > > > +int board_phy_config(struct phy_device *phydev) > > > > +{ > > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); > > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); > > > > + > > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); > > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); > > > > + > > > > + if (phydev->drv->config) > > > > + phydev->drv->config(phydev); > > > > + > > > > + return 0; > > > > +} > > > > +#endif > > > > + > > > > +int checkboard(void) > > > > +{ > > > > + puts("Board: iMX8QXP AI_ML\n"); > > > > + > > > > + build_info(); > > > > + print_bootinfo(); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +int board_init(void) > > > > +{ > > > > + board_gpio_init(); > > > > + > > > > + return 0; > > > > +} > > > > > > Here you call the empty board_gpio_init(). > > > > > > > As per above comment, I'll remove it. > > > > > > + > > > > +/* Board specific reset that is system reset */ > > > > + > > > > +void reset_cpu(ulong addr) > > > > +{ > > > > + /* TODO */ > > > > +} > > > > > > Maybe you could use the SYSRESET driver from the outset? It > > > internally uses WDT for reset. > > > > > > > Hmm, looks like there is no watchdog driver for imx8qxp yet. > > If I may ask - how do you plan to reset the board? On most i.MX boards > the reset is done by triggering the WDT. > For i.MX8 boards, there is no reset support in u-boot. So I'll bank on the NXP folks to add it :-) On the linux side, we have the watchdog driver which will do SMC call to trigger reset. > > > > > > + > > > > +#ifdef CONFIG_OF_BOARD_SETUP > > > > +int ft_board_setup(void *blob, bd_t *bd) > > > > +{ > > > > + return 0; > > > > +} > > > > +#endif > > > > + > > > > +int board_mmc_get_env_dev(int devno) > > > > +{ > > > > + return devno; > > > > +} > > > > > > This (the device and its instance) could be set in Kconfig. > > > > > > > Ack. > > > > > > + > > > > +int board_late_init(void) > > > > +{ > > > > + return 0; > > > > +} > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/imximage.cfg > > > > b/board/einfochips/imx8qxp_ai_ml/imximage.cfg new file mode 100644 > > > > index 0000000000..4fc5ade313 > > > > --- /dev/null > > > > +++ b/board/einfochips/imx8qxp_ai_ml/imximage.cfg > > > > @@ -0,0 +1,24 @@ > > > > +/* SPDX-License-Identifier: GPL-2.0+ */ > > > > +/* > > > > + * Copyright 2018 NXP > > > > + * > > > > + * Refer doc/README.imx8image for more details about how-to > > > > configure > > > > + * and create imx8image boot image > > > > + */ > > > > + > > > > +#define __ASSEMBLY__ > > > > + > > > > +/* Boot from SD, sector size 0x400 */ > > > > +BOOT_FROM SD 0x400 > > > > +/* SoC type IMX8QX */ > > > > +SOC_TYPE IMX8QX > > > > +/* Append seco container image */ > > > > +APPEND mx8qx-ahab-container.img > > > > +/* Create the 2nd container */ > > > > +CONTAINER > > > > +/* Add scfw image with exec attribute */ > > > > +IMAGE SCU mx8qx-aiml-scfw-tcm.bin > > > > +/* Add ATF image with exec attribute */ > > > > +IMAGE A35 bl31.bin 0x80000000 > > > > +/* Add U-Boot image with load attribute */ > > > > +DATA A35 u-boot-dtb.bin 0x80020000 > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/spl.c > > > > b/board/einfochips/imx8qxp_ai_ml/spl.c new file mode 100644 > > > > index 0000000000..63581eeaaf > > > > --- /dev/null > > > > +++ b/board/einfochips/imx8qxp_ai_ml/spl.c > > > > @@ -0,0 +1,49 @@ > > > > +/* > > > > + * Copyright 2018 NXP > > > > + * > > > > + * SPDX-License-Identifier: GPL-2.0+ > > > > + */ > > > > + > > > > +#include <common.h> > > > > +#include <dm.h> > > > > +#include <spl.h> > > > > +#include <dm/uclass.h> > > > > +#include <dm/device.h> > > > > +#include <dm/uclass-internal.h> > > > > +#include <dm/device-internal.h> > > > > +#include <dm/lists.h> > > > > + > > > > +DECLARE_GLOBAL_DATA_PTR; > > > > + > > > > +void spl_board_init(void) > > > > +{ > > > > + struct udevice *dev; > > > > + > > > > + uclass_find_first_device(UCLASS_MISC, &dev); > > > > + > > > > + for (; dev; uclass_find_next_device(&dev)) { > > > > + if (device_probe(dev)) > > > > + continue; > > > > + } > > > > > > What devices needs to be initialized in that way ? > > > > > > > Mostly SCU but it is not needed, so I'll remove it. > > Ok. > > > > > > > + > > > > + arch_cpu_init(); > > > > + > > > > + board_early_init_f(); > > > > + > > > > + timer_init(); > > > > + > > > > + preloader_console_init(); > > > > + > > > > + puts("Normal Boot\n"); > > > > +} > > > > + > > > > +void board_init_f(ulong dummy) > > > > +{ > > > > + /* Clear global data */ > > > > + memset((void *)gd, 0, sizeof(gd_t)); > > > > + > > > > + /* Clear the BSS. */ > > > > + memset(__bss_start, 0, __bss_end - __bss_start); > > > > + > > > > + board_init_r(NULL, 0); > > > > +} > > > > diff --git a/configs/imx8qxp_ai_ml_defconfig > > > > b/configs/imx8qxp_ai_ml_defconfig new file mode 100644 > > > > index 0000000000..e20a0c783e > > > > --- /dev/null > > > > +++ b/configs/imx8qxp_ai_ml_defconfig > > > > @@ -0,0 +1,83 @@ > > > > +CONFIG_ARM=y > > > > +CONFIG_ARCH_IMX8=y > > > > +CONFIG_SYS_TEXT_BASE=0x80020000 > > > > +CONFIG_DISTRO_DEFAULTS=y > > > > +CONFIG_SPL_GPIO_SUPPORT=y > > > > +CONFIG_SPL_LIBCOMMON_SUPPORT=y > > > > +CONFIG_SPL_LIBGENERIC_SUPPORT=y > > > > +CONFIG_SYS_MALLOC_F_LEN=0x4000 > > > > +CONFIG_TARGET_IMX8QXP_AI_ML=y > > > > +CONFIG_SPL_MMC_SUPPORT=y > > > > +CONFIG_SPL_SERIAL_SUPPORT=y > > > > +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y > > > > +CONFIG_NR_DRAM_BANKS=4 > > > > +CONFIG_SPL=y > > > > +CONFIG_FIT=y > > > > +CONFIG_SPL_LOAD_FIT=y > > > > +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" > > > > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/einfochips/imx8qxp_ai_ml/imximage.cfg" > > > > +CONFIG_BOOTDELAY=3 > > > > +CONFIG_LOG=y > > > > +CONFIG_SPL_BOARD_INIT=y > > > > +CONFIG_SPL_SYS_MALLOC_SIMPLE=y > > > > +CONFIG_SPL_SEPARATE_BSS=y > > > > +CONFIG_SPL_POWER_SUPPORT=y > > > > +CONFIG_SPL_POWER_DOMAIN=y > > > > +CONFIG_SPL_WATCHDOG_SUPPORT=y > > > > +CONFIG_HUSH_PARSER=y > > > > +CONFIG_CMD_CPU=y > > > > +# CONFIG_CMD_IMPORTENV is not set > > > > +CONFIG_CMD_CLK=y > > > > +CONFIG_CMD_DM=y > > > > +CONFIG_CMD_FUSE=y > > > > +CONFIG_CMD_GPIO=y > > > > +CONFIG_CMD_GPT=y > > > > +CONFIG_CMD_I2C=y > > > > +CONFIG_CMD_MMC=y > > > > +CONFIG_CMD_DHCP=y > > > > +CONFIG_CMD_MII=y > > > > +CONFIG_CMD_PING=y > > > > +CONFIG_CMD_CACHE=y > > > > +CONFIG_CMD_EXT4=y > > > > +CONFIG_CMD_EXT4_WRITE=y > > > > +CONFIG_CMD_FAT=y > > > > +CONFIG_FAT_WRITE=y > > > > +CONFIG_CMD_FS_GENERIC=y > > > > +CONFIG_SPL_OF_CONTROL=y > > > > +CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qxp-ai_ml" > > > > +CONFIG_ENV_IS_IN_MMC=y > > > > +CONFIG_SPL_DM=y > > > > +CONFIG_SPL_CLK=y > > > > +CONFIG_CLK_IMX8=y > > > > +CONFIG_CPU=y > > > > +CONFIG_DM_GPIO=y > > > > +CONFIG_MXC_GPIO=y > > > > +CONFIG_DM_I2C=y > > > > +CONFIG_SYS_I2C_IMX_LPI2C=y > > > > +CONFIG_MISC=y > > > > +CONFIG_DM_MMC=y > > > > +CONFIG_FSL_ESDHC=y > > > > +CONFIG_PHYLIB=y > > > > +CONFIG_PHY_ADDR_ENABLE=y > > > > +CONFIG_PHY_ATHEROS=y > > > > +CONFIG_DM_ETH=y > > > > +CONFIG_NET_RANDOM_ETHADDR=y > > > > +CONFIG_PHY_GIGE=y > > > > +CONFIG_FEC_MXC_SHARE_MDIO=y > > > > +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000 > > > > +CONFIG_FEC_MXC=y > > > > +CONFIG_MII=y > > > > +CONFIG_PINCTRL=y > > > > +CONFIG_SPL_PINCTRL=y > > > > +CONFIG_PINCTRL_IMX8=y > > > > +CONFIG_POWER_DOMAIN=y > > > > +CONFIG_IMX8_POWER_DOMAIN=y > > > > +CONFIG_DM_REGULATOR=y > > > > +CONFIG_SPL_DM_REGULATOR=y > > > > +CONFIG_DM_REGULATOR_FIXED=y > > > > +CONFIG_DM_REGULATOR_GPIO=y > > > > +CONFIG_SPL_DM_REGULATOR_GPIO=y > > > > +CONFIG_DM_SERIAL=y > > > > +CONFIG_FSL_LPUART=y > > > > +CONFIG_SPL_TINY_MEMSET=y > > > > +# CONFIG_EFI_LOADER is not set > > > > diff --git a/include/configs/imx8qxp_ai_ml.h > > > > b/include/configs/imx8qxp_ai_ml.h new file mode 100644 > > > > index 0000000000..dd31189845 > > > > --- /dev/null > > > > +++ b/include/configs/imx8qxp_ai_ml.h > > > > @@ -0,0 +1,104 @@ > > > > +/* SPDX-License-Identifier: GPL-2.0+ */ > > > > +/* > > > > + * Copyright 2018 NXP > > > > + * Copyright 2019 Linaro Ltd. > > > > + */ > > > > + > > > > +#ifndef __IMX8QXP_AI_ML_H > > > > +#define __IMX8QXP_AI_ML_H > > > > + > > > > +#include <linux/sizes.h> > > > > +#include <asm/arch/imx-regs.h> > > > > + > > > > +#ifdef CONFIG_SPL_BUILD > > > > +#define CONFIG_SPL_MAX_SIZE (124 * > > > > 1024) +#define CONFIG_SYS_MONITOR_LEN > > > > (1024 * 1024) +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR > > > > +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR > > > > 0x250 +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0 > > > > + > > > > +#define > > > > CONFIG_SPL_LDSCRIPT > > > > "arch/arm/cpu/armv8/u-boot-spl.lds" +#define > > > > CONFIG_SPL_STACK 0x013E000 +#define > > > > CONFIG_SPL_BSS_START_ADDR 0x00128000 +#define > > > > CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */ > > > > +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000 +#define > > > > CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */ > > > > +#define CONFIG_SERIAL_LPUART_BASE 0x5a080000 +#define > > > > CONFIG_MALLOC_F_ADDR 0x00120000 + +#define > > > > CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE + > > > > +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE > > > > + > > > > +#define CONFIG_OF_EMBED > > > > > > I'm not sure if the OF_EMBED is not deprecated ... and replaced by > > > OF_SEPARATED. > > > > > > > I'm not sure about this. I don't see any such information. > > There was a u-boot ML discussion about OF_EMBED deprecation. > https://patchwork.ozlabs.org/project/uboot/list/?series=&submitter=&state=*&q=OF_EMBED&archive=both&delegate= > > Also please see: > https://www.chromium.org/developers/u-boot > Okay, thanks for the pointer. > > > > > > +#endif > > > > + > > > > +#define CONFIG_REMAKE_ELF > > > > + > > > > +#define CONFIG_BOARD_EARLY_INIT_F > > > > > > This could be set in Kconfig, IIRC > > > > > > > Ack. > > > > > > + > > > > +/* Flat Device Tree Definitions */ > > > > +#define CONFIG_OF_BOARD_SETUP > > > > + > > > > +#define CONFIG_FSL_USDHC > > > > + > > > > +#define CONFIG_ENV_OVERWRITE > > > > + > > > > +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG > > > > + > > > > +#define BOOT_TARGET_DEVICES(func) \ > > > > + func(MMC, mmc, 1) \ > > > > + func(DHCP, dhcp, na) > > > > + > > > > +#include <config_distro_bootcmd.h> > > > > +/* Initial environment variables */ > > > > +#define CONFIG_EXTRA_ENV_SETTINGS > > > > \ > > > > + "console=ttyLP2 earlycon\0" \ > > > > + "fdt_addr_r=0x83000000\0" \ > > > > + "kernel_addr_r=0x81000000\0" \ > > > > + "ramdisk_addr_r=0x94400000\0" \ > > > > + "scriptaddr=0x89000000\0" \ > > > > + "fdtfile=imx8qxp-ai_ml.dtb\0" \ > > > > + "fdt_high=0xffffffffffffffff\0" \ > > > > + "image=Image\0" \ > > > > + "initrd_addr=0x83800000\0" \ > > > > + "initrd_high=0xffffffffffffffff\0" \ > > > > + "netargs=setenv bootargs console=${console},${baudrate} > > > > " \ > > > > + "root=/dev/nfs ip=dhcp > > > > nfsroot=${serverip}:${nfsroot},v3,tcp" \ > > > > + "\0" \ > > > > + "nfsboot=run netargs; dhcp ${loadaddr} ${image}; tftp > > > > ${fdt_addr} " \ > > > > + "imx8qxp-ai_ml/${fdt_file}; booti ${loadaddr} - > > > > ${fdt_addr}\0" \ > > > > + BOOTENV > > > > + > > > > +/* Link Definitions */ > > > > +#define CONFIG_LOADADDR 0x80280000 > > > > + > > > > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR > > > > + > > > > +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000 > > > > + > > > > +/* Default environment is in SD */ > > > > +#define CONFIG_ENV_SIZE 0x1000 > > > > +#define CONFIG_ENV_OFFSET (64 * SZ_64K) > > > > + > > > > +/* USDHC2 is the SD card interface */ > > > > +#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */ > > > > +#define CONFIG_SYS_FSL_USDHC_NUM 2 > > > > + > > > > > > Some of those env setting defines as well as eMMC ones could be set > > > now in Kconfig. > > > > > > > Can you please specify those? I don't see these defines used in > > Kconfig. > > The best (and simplest) way is to just check if the corresponding > CONFIG_* option is already moved (ported) to Kconfig. For > example ENV_SIZE and ENV_OFFSET are. > Yeah, I see it now that couple of boards are using it. Will do the same. Thanks, Mani > > > > > > +/* Size of malloc() pool */ > > > > +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + > > > > (32 > > > > * 1024)) * 1024) + > > > > +#define CONFIG_SYS_SDRAM_BASE 0x80000000 > > > > +#define PHYS_SDRAM_1 0x80000000 > > > > +#define PHYS_SDRAM_2 0x880000000 > > > > +#define PHYS_SDRAM_1_SIZE SZ_2G /* > > > > 2 > > > > > > Please fix this file globally, to use "SZ_XX" instead of magic > > > numbers. > > > > Ack. > > > > Thanks, > > Mani > > > > > > GB */ +#define PHYS_SDRAM_2_SIZE 0x00000000 > > > > /* 0 GB */ + > > > > +/* Generic Timer Definitions */ > > > > +#define COUNTER_FREQUENCY 8000000 /* 8MHz > > > > */ + > > > > +/* Networking */ > > > > +#define CONFIG_FEC_XCV_TYPE RGMII > > > > +#define FEC_QUIRK_ENET_MAC > > > > + > > > > +#endif /* __IMX8QXP_AI_ML_H */ > > > > > > > > > > > > > > > Best regards, > > > > > > Lukasz Majewski > > > > > > -- > > > > > > DENX Software Engineering GmbH, Managing Director: Wolfgang > > > Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, > > > Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: > > > lukma@denx.de > > > > > > > > Best regards, > > Lukasz Majewski > > -- > > DENX Software Engineering GmbH, Managing Director: Wolfgang Denk > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany > Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de
On Thu, 15 Aug 2019 13:46:30 +0530 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> wrote: > Hi Lukasz, > > On Thu, Aug 15, 2019 at 09:51:25AM +0200, Lukasz Majewski wrote: > > Hi Manivannan, > > > > > Hi Lukasz, > > > > > > Thanks for the review! > > > > > > On Wed, Jul 24, 2019 at 10:07:13AM +0200, Lukasz Majewski wrote: > > > > Hi Manivannan, > > > > > > > > > This commit adds initial board support for iMX8QXP AI_ML board > > > > > from Einfochips. This board is one of the 96Boards Consumer > > > > > Edition and AI boards of the 96Boards family based on i.MX8QXP > > > > > SoC from NXP/Freescale. > > > > > > > > > > This initial supports contains following peripherals which are > > > > > tested and known to work: > > > > > > > > > > 1. Debug serial via UART2 > > > > > 2. SD card > > > > > 3. Ethernet > > > > > > > > > > More information about this board can be found in arrow > > > > > website: > > > > > https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools > > > > > > > > > > Signed-off-by: Manivannan Sadhasivam > > > > > <manivannan.sadhasivam@linaro.org> --- > > > > > arch/arm/mach-imx/imx8/Kconfig | 6 + > > > > > board/einfochips/imx8qxp_ai_ml/Kconfig | 12 ++ > > > > > board/einfochips/imx8qxp_ai_ml/MAINTAINERS | 6 + > > > > > board/einfochips/imx8qxp_ai_ml/Makefile | 8 ++ > > > > > board/einfochips/imx8qxp_ai_ml/README | 49 ++++++++ > > > > > .../einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c | 117 > > > > > ++++++++++++++++++ > > > > > board/einfochips/imx8qxp_ai_ml/imximage.cfg | 24 ++++ > > > > > board/einfochips/imx8qxp_ai_ml/spl.c | 49 ++++++++ > > > > > configs/imx8qxp_ai_ml_defconfig | 83 > > > > > +++++++++++++ include/configs/imx8qxp_ai_ml.h | > > > > > 104 ++++++++++++++++ 10 files changed, 458 insertions(+) > > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/Kconfig > > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/Makefile > > > > > create mode 100644 board/einfochips/imx8qxp_ai_ml/README > > > > > create mode 100644 > > > > > board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c create mode > > > > > 100644 board/einfochips/imx8qxp_ai_ml/imximage.cfg create > > > > > mode 100644 board/einfochips/imx8qxp_ai_ml/spl.c create mode > > > > > 100644 configs/imx8qxp_ai_ml_defconfig create mode 100644 > > > > > include/configs/imx8qxp_ai_ml.h > > > > > > > > > > diff --git a/arch/arm/mach-imx/imx8/Kconfig > > > > > b/arch/arm/mach-imx/imx8/Kconfig index bbe323d5ca..cec21f8dd2 > > > > > 100644 --- a/arch/arm/mach-imx/imx8/Kconfig > > > > > +++ b/arch/arm/mach-imx/imx8/Kconfig > > > > > @@ -37,6 +37,11 @@ config TARGET_COLIBRI_IMX8X > > > > > select BOARD_LATE_INIT > > > > > select IMX8QXP > > > > > > > > > > +config TARGET_IMX8QXP_AI_ML > > > > > + bool "Support i.MX8QXP AI_ML board" > > > > > + select BOARD_LATE_INIT > > > > > + select IMX8QXP > > > > > + > > > > > config TARGET_IMX8QM_MEK > > > > > bool "Support i.MX8QM MEK board" > > > > > select BOARD_LATE_INIT > > > > > @@ -49,6 +54,7 @@ config TARGET_IMX8QXP_MEK > > > > > > > > > > endchoice > > > > > > > > > > +source "board/einfochips/imx8qxp_ai_ml/Kconfig" > > > > > source "board/freescale/imx8qm_mek/Kconfig" > > > > > source "board/freescale/imx8qxp_mek/Kconfig" > > > > > source "board/toradex/apalis-imx8/Kconfig" > > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/Kconfig > > > > > b/board/einfochips/imx8qxp_ai_ml/Kconfig new file mode 100644 > > > > > index 0000000000..697a831013 > > > > > --- /dev/null > > > > > +++ b/board/einfochips/imx8qxp_ai_ml/Kconfig > > > > > @@ -0,0 +1,12 @@ > > > > > +if TARGET_IMX8QXP_AI_ML > > > > > + > > > > > +config SYS_BOARD > > > > > + default "imx8qxp_ai_ml" > > > > > + > > > > > +config SYS_VENDOR > > > > > + default "einfochips" > > > > > + > > > > > +config SYS_CONFIG_NAME > > > > > + default "imx8qxp_ai_ml" > > > > > + > > > > > +endif > > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > > > > b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS new file mode > > > > > 100644 index 0000000000..add0bd9431 > > > > > --- /dev/null > > > > > +++ b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS > > > > > @@ -0,0 +1,6 @@ > > > > > +i.MX8QXP AI_ML BOARD > > > > > +M: Manivannan Sadhasivam > > > > > <manivannan.sadhasivam@linaro.org> +S: Maintained > > > > > +F: board/einfochips/imx8qxp_ai_ml/ > > > > > +F: include/configs/imx8qxp_ai_ml.h > > > > > +F: configs/imx8qxp_ai_ml_defconfig > > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/Makefile > > > > > b/board/einfochips/imx8qxp_ai_ml/Makefile new file mode 100644 > > > > > index 0000000000..e08774dc6e > > > > > --- /dev/null > > > > > +++ b/board/einfochips/imx8qxp_ai_ml/Makefile > > > > > @@ -0,0 +1,8 @@ > > > > > +# > > > > > +# Copyright 2019 Linaro Ltd. > > > > > +# > > > > > +# SPDX-License-Identifier: GPL-2.0+ > > > > > +# > > > > > + > > > > > +obj-y += imx8qxp_ai_ml.o > > > > > +obj-$(CONFIG_SPL_BUILD) += spl.o > > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/README > > > > > b/board/einfochips/imx8qxp_ai_ml/README new file mode 100644 > > > > > index 0000000000..488920580f > > > > > --- /dev/null > > > > > +++ b/board/einfochips/imx8qxp_ai_ml/README > > > > > > > > Thank you for preparing the README file, appreciated :-). > > > > > > > > > @@ -0,0 +1,49 @@ > > > > > +U-Boot for the Einfochips i.MX8QXP AI_ML board > > > > > + > > > > > +Quick Start > > > > > +=========== > > > > > + > > > > > +- Get and Build the ARM Trusted firmware > > > > > +- Get scfw_tcm.bin and ahab-container.img > > > > > +- Build U-Boot > > > > > +- Flash the binary into the SD card > > > > > +- Boot > > > > > + > > > > > +Get and Build the ARM Trusted firmware > > > > > +====================================== > > > > > + > > > > > +$ git clone > > > > > https://source.codeaurora.org/external/imx/imx-atf +$ cd > > > > > imx-atf/ +$ git checkout origin/imx_4.9.88_imx8qxp_beta2 -b > > > > > imx_4.9.88_imx8qxp_beta2 +$ make PLAT=imx8qxp bl31 > > > > > + > > > > > +Get scfw_tcm.bin and ahab-container.img > > > > > +======================================= > > > > > + > > > > > +$ wget > > > > > https://raw.githubusercontent.com/96boards-ai-ml/binaries/master/mx8qx-aiml-scfw-tcm.bin > > > > > +$ wget > > > > > https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.1.bin > > > > > +$ chmod +x firmware-imx-8.1.bin +$ ./firmware-imx-8.1.bin + > > > > > +Copy the following binaries to U-Boot folder: > > > > > + > > > > > +$ cp imx-atf/build/imx8qxp/release/bl31.bin . > > > > > +$ cp firmware-imx-8.1/firmware/seco/mx8qx-ahab-container.img > > > > > . + > > > > > +Build U-Boot > > > > > +============ > > > > > + > > > > > +$ make imx8qxp_ai_ml_defconfig > > > > > +$ make u-boot-dtb.imx > > > > > + > > > > > +Flash the binary into the SD card > > > > > +================================= > > > > > + > > > > > +Burn the u-boot-dtb.imx binary to SD card offset 32KB: > > > > > + > > > > > +$ sudo dd if=u-boot-dtb.imx of=/dev/sd[x] bs=1024 seek=32 > > > > > + > > > > > +Boot > > > > > +==== > > > > > + > > > > > +Set Boot switch SW2: 1100. > > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > > > > b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c new file mode > > > > > 100644 index 0000000000..e7632524a0 > > > > > --- /dev/null > > > > > +++ b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c > > > > > @@ -0,0 +1,117 @@ > > > > > +// SPDX-License-Identifier: GPL-2.0+ > > > > > +/* > > > > > + * Copyright 2018 NXP > > > > > + * Copyright 2019 Linaro Ltd. > > > > > + */ > > > > > + > > > > > +#include <common.h> > > > > > +#include <errno.h> > > > > > +#include <linux/libfdt.h> > > > > > +#include <environment.h> > > > > > +#include <fsl_esdhc.h> > > > > > +#include <asm/io.h> > > > > > +#include <asm/arch/clock.h> > > > > > +#include <asm/arch/sci/sci.h> > > > > > +#include <asm/arch/imx8-pins.h> > > > > > +#include <asm/arch/iomux.h> > > > > > +#include <asm/arch/sys_proto.h> > > > > > + > > > > > +DECLARE_GLOBAL_DATA_PTR; > > > > > + > > > > > +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << > > > > > PADRING_CONFIG_SHIFT) | \ > > > > > + (SC_PAD_ISO_OFF << > > > > > PADRING_LPCONFIG_SHIFT) | \ > > > > > + (SC_PAD_28FDSOI_DSE_DV_HIGH << > > > > > PADRING_DSE_SHIFT) | \ > > > > > + (SC_PAD_28FDSOI_PS_PU << > > > > > PADRING_PULL_SHIFT)) + > > > > > +static iomux_cfg_t uart2_pads[] = { > > > > > + SC_P_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL), > > > > > + SC_P_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL), > > > > > +}; > > > > > > > > As fair as I see - the uart could be configured via DTS (by > > > > using the pinmux driver) as this is the U-Boot proper file. > > > > > > > > > > Agree, this is not needed. > > > > > > > > + > > > > > +static void setup_iomux_uart(void) > > > > > +{ > > > > > + imx8_iomux_setup_multiple_pads(uart2_pads, > > > > > ARRAY_SIZE(uart2_pads)); +} > > > > > + > > > > > +int board_early_init_f(void) > > > > > +{ > > > > > + sc_pm_clock_rate_t rate = SC_80MHZ; > > > > > + int ret; > > > > > + > > > > > + /* Set UART2 clock root to 80 MHz */ > > > > > + ret = sc_pm_setup_uart(SC_R_UART_2, rate); > > > > > + if (ret) > > > > > + return ret; > > > > > + > > > > > + setup_iomux_uart(); > > > > > + > > > > > + return 0; > > > > > +} > > > > > + > > > > > +#if IS_ENABLED(CONFIG_DM_GPIO) > > > > > +static void board_gpio_init(void) > > > > > +{ > > > > > + /* TODO */ > > > > > +} > > > > > +#else > > > > > +static inline void board_gpio_init(void) {} > > > > > +#endif > > > > > + > > > > > > > > I'm wondering if the above function is needed? > > > > > > > > > > I thought about keeping this as I may add some gpio configurations > > > in future. But, yeah I can remove it now and add once needed. > > > > The general rule is to avoid adding any dead (i.e. not used) code to > > the main line. > > > > The practical reason for it is to have the code base as small as > > possible. Moreover, the patch, which adds this board is rather > > large, so in that way we make it smaller. > > > > This code shall be added when you introduce the GPIO needed for this > > board. > > > > Okay, thanks for the info! > > > > > > > > > +#if IS_ENABLED(CONFIG_FEC_MXC) > > > > > +#include <miiphy.h> > > > > > + > > > > > +int board_phy_config(struct phy_device *phydev) > > > > > +{ > > > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); > > > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); > > > > > + > > > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); > > > > > + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); > > > > > + > > > > > + if (phydev->drv->config) > > > > > + phydev->drv->config(phydev); > > > > > + > > > > > + return 0; > > > > > +} > > > > > +#endif > > > > > + > > > > > +int checkboard(void) > > > > > +{ > > > > > + puts("Board: iMX8QXP AI_ML\n"); > > > > > + > > > > > + build_info(); > > > > > + print_bootinfo(); > > > > > + > > > > > + return 0; > > > > > +} > > > > > + > > > > > +int board_init(void) > > > > > +{ > > > > > + board_gpio_init(); > > > > > + > > > > > + return 0; > > > > > +} > > > > > > > > Here you call the empty board_gpio_init(). > > > > > > > > > > As per above comment, I'll remove it. > > > > > > > > + > > > > > +/* Board specific reset that is system reset */ > > > > > + > > > > > +void reset_cpu(ulong addr) > > > > > +{ > > > > > + /* TODO */ > > > > > +} > > > > > > > > Maybe you could use the SYSRESET driver from the outset? It > > > > internally uses WDT for reset. > > > > > > > > > > Hmm, looks like there is no watchdog driver for imx8qxp yet. > > > > If I may ask - how do you plan to reset the board? On most i.MX > > boards the reset is done by triggering the WDT. > > > > For i.MX8 boards, there is no reset support in u-boot. So I'll bank > on the NXP folks to add it :-) On the linux side, we have the > watchdog driver which will do SMC call to trigger reset. Then please state in the commit message that the 'reset' is not working (at least via WDT). > > > > > > > > > + > > > > > +#ifdef CONFIG_OF_BOARD_SETUP > > > > > +int ft_board_setup(void *blob, bd_t *bd) > > > > > +{ > > > > > + return 0; > > > > > +} > > > > > +#endif > > > > > + > > > > > +int board_mmc_get_env_dev(int devno) > > > > > +{ > > > > > + return devno; > > > > > +} > > > > > > > > This (the device and its instance) could be set in Kconfig. > > > > > > > > > > Ack. > > > > > > > > + > > > > > +int board_late_init(void) > > > > > +{ > > > > > + return 0; > > > > > +} > > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/imximage.cfg > > > > > b/board/einfochips/imx8qxp_ai_ml/imximage.cfg new file mode > > > > > 100644 index 0000000000..4fc5ade313 > > > > > --- /dev/null > > > > > +++ b/board/einfochips/imx8qxp_ai_ml/imximage.cfg > > > > > @@ -0,0 +1,24 @@ > > > > > +/* SPDX-License-Identifier: GPL-2.0+ */ > > > > > +/* > > > > > + * Copyright 2018 NXP > > > > > + * > > > > > + * Refer doc/README.imx8image for more details about how-to > > > > > configure > > > > > + * and create imx8image boot image > > > > > + */ > > > > > + > > > > > +#define __ASSEMBLY__ > > > > > + > > > > > +/* Boot from SD, sector size 0x400 */ > > > > > +BOOT_FROM SD 0x400 > > > > > +/* SoC type IMX8QX */ > > > > > +SOC_TYPE IMX8QX > > > > > +/* Append seco container image */ > > > > > +APPEND mx8qx-ahab-container.img > > > > > +/* Create the 2nd container */ > > > > > +CONTAINER > > > > > +/* Add scfw image with exec attribute */ > > > > > +IMAGE SCU mx8qx-aiml-scfw-tcm.bin > > > > > +/* Add ATF image with exec attribute */ > > > > > +IMAGE A35 bl31.bin 0x80000000 > > > > > +/* Add U-Boot image with load attribute */ > > > > > +DATA A35 u-boot-dtb.bin 0x80020000 > > > > > diff --git a/board/einfochips/imx8qxp_ai_ml/spl.c > > > > > b/board/einfochips/imx8qxp_ai_ml/spl.c new file mode 100644 > > > > > index 0000000000..63581eeaaf > > > > > --- /dev/null > > > > > +++ b/board/einfochips/imx8qxp_ai_ml/spl.c > > > > > @@ -0,0 +1,49 @@ > > > > > +/* > > > > > + * Copyright 2018 NXP > > > > > + * > > > > > + * SPDX-License-Identifier: GPL-2.0+ > > > > > + */ > > > > > + > > > > > +#include <common.h> > > > > > +#include <dm.h> > > > > > +#include <spl.h> > > > > > +#include <dm/uclass.h> > > > > > +#include <dm/device.h> > > > > > +#include <dm/uclass-internal.h> > > > > > +#include <dm/device-internal.h> > > > > > +#include <dm/lists.h> > > > > > + > > > > > +DECLARE_GLOBAL_DATA_PTR; > > > > > + > > > > > +void spl_board_init(void) > > > > > +{ > > > > > + struct udevice *dev; > > > > > + > > > > > + uclass_find_first_device(UCLASS_MISC, &dev); > > > > > + > > > > > + for (; dev; uclass_find_next_device(&dev)) { > > > > > + if (device_probe(dev)) > > > > > + continue; > > > > > + } > > > > > > > > What devices needs to be initialized in that way ? > > > > > > > > > > Mostly SCU but it is not needed, so I'll remove it. > > > > Ok. > > > > > > > > > > + > > > > > + arch_cpu_init(); > > > > > + > > > > > + board_early_init_f(); > > > > > + > > > > > + timer_init(); > > > > > + > > > > > + preloader_console_init(); > > > > > + > > > > > + puts("Normal Boot\n"); > > > > > +} > > > > > + > > > > > +void board_init_f(ulong dummy) > > > > > +{ > > > > > + /* Clear global data */ > > > > > + memset((void *)gd, 0, sizeof(gd_t)); > > > > > + > > > > > + /* Clear the BSS. */ > > > > > + memset(__bss_start, 0, __bss_end - __bss_start); > > > > > + > > > > > + board_init_r(NULL, 0); > > > > > +} > > > > > diff --git a/configs/imx8qxp_ai_ml_defconfig > > > > > b/configs/imx8qxp_ai_ml_defconfig new file mode 100644 > > > > > index 0000000000..e20a0c783e > > > > > --- /dev/null > > > > > +++ b/configs/imx8qxp_ai_ml_defconfig > > > > > @@ -0,0 +1,83 @@ > > > > > +CONFIG_ARM=y > > > > > +CONFIG_ARCH_IMX8=y > > > > > +CONFIG_SYS_TEXT_BASE=0x80020000 > > > > > +CONFIG_DISTRO_DEFAULTS=y > > > > > +CONFIG_SPL_GPIO_SUPPORT=y > > > > > +CONFIG_SPL_LIBCOMMON_SUPPORT=y > > > > > +CONFIG_SPL_LIBGENERIC_SUPPORT=y > > > > > +CONFIG_SYS_MALLOC_F_LEN=0x4000 > > > > > +CONFIG_TARGET_IMX8QXP_AI_ML=y > > > > > +CONFIG_SPL_MMC_SUPPORT=y > > > > > +CONFIG_SPL_SERIAL_SUPPORT=y > > > > > +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y > > > > > +CONFIG_NR_DRAM_BANKS=4 > > > > > +CONFIG_SPL=y > > > > > +CONFIG_FIT=y > > > > > +CONFIG_SPL_LOAD_FIT=y > > > > > +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" > > > > > +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/einfochips/imx8qxp_ai_ml/imximage.cfg" > > > > > +CONFIG_BOOTDELAY=3 > > > > > +CONFIG_LOG=y > > > > > +CONFIG_SPL_BOARD_INIT=y > > > > > +CONFIG_SPL_SYS_MALLOC_SIMPLE=y > > > > > +CONFIG_SPL_SEPARATE_BSS=y > > > > > +CONFIG_SPL_POWER_SUPPORT=y > > > > > +CONFIG_SPL_POWER_DOMAIN=y > > > > > +CONFIG_SPL_WATCHDOG_SUPPORT=y > > > > > +CONFIG_HUSH_PARSER=y > > > > > +CONFIG_CMD_CPU=y > > > > > +# CONFIG_CMD_IMPORTENV is not set > > > > > +CONFIG_CMD_CLK=y > > > > > +CONFIG_CMD_DM=y > > > > > +CONFIG_CMD_FUSE=y > > > > > +CONFIG_CMD_GPIO=y > > > > > +CONFIG_CMD_GPT=y > > > > > +CONFIG_CMD_I2C=y > > > > > +CONFIG_CMD_MMC=y > > > > > +CONFIG_CMD_DHCP=y > > > > > +CONFIG_CMD_MII=y > > > > > +CONFIG_CMD_PING=y > > > > > +CONFIG_CMD_CACHE=y > > > > > +CONFIG_CMD_EXT4=y > > > > > +CONFIG_CMD_EXT4_WRITE=y > > > > > +CONFIG_CMD_FAT=y > > > > > +CONFIG_FAT_WRITE=y > > > > > +CONFIG_CMD_FS_GENERIC=y > > > > > +CONFIG_SPL_OF_CONTROL=y > > > > > +CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qxp-ai_ml" > > > > > +CONFIG_ENV_IS_IN_MMC=y > > > > > +CONFIG_SPL_DM=y > > > > > +CONFIG_SPL_CLK=y > > > > > +CONFIG_CLK_IMX8=y > > > > > +CONFIG_CPU=y > > > > > +CONFIG_DM_GPIO=y > > > > > +CONFIG_MXC_GPIO=y > > > > > +CONFIG_DM_I2C=y > > > > > +CONFIG_SYS_I2C_IMX_LPI2C=y > > > > > +CONFIG_MISC=y > > > > > +CONFIG_DM_MMC=y > > > > > +CONFIG_FSL_ESDHC=y > > > > > +CONFIG_PHYLIB=y > > > > > +CONFIG_PHY_ADDR_ENABLE=y > > > > > +CONFIG_PHY_ATHEROS=y > > > > > +CONFIG_DM_ETH=y > > > > > +CONFIG_NET_RANDOM_ETHADDR=y > > > > > +CONFIG_PHY_GIGE=y > > > > > +CONFIG_FEC_MXC_SHARE_MDIO=y > > > > > +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000 > > > > > +CONFIG_FEC_MXC=y > > > > > +CONFIG_MII=y > > > > > +CONFIG_PINCTRL=y > > > > > +CONFIG_SPL_PINCTRL=y > > > > > +CONFIG_PINCTRL_IMX8=y > > > > > +CONFIG_POWER_DOMAIN=y > > > > > +CONFIG_IMX8_POWER_DOMAIN=y > > > > > +CONFIG_DM_REGULATOR=y > > > > > +CONFIG_SPL_DM_REGULATOR=y > > > > > +CONFIG_DM_REGULATOR_FIXED=y > > > > > +CONFIG_DM_REGULATOR_GPIO=y > > > > > +CONFIG_SPL_DM_REGULATOR_GPIO=y > > > > > +CONFIG_DM_SERIAL=y > > > > > +CONFIG_FSL_LPUART=y > > > > > +CONFIG_SPL_TINY_MEMSET=y > > > > > +# CONFIG_EFI_LOADER is not set > > > > > diff --git a/include/configs/imx8qxp_ai_ml.h > > > > > b/include/configs/imx8qxp_ai_ml.h new file mode 100644 > > > > > index 0000000000..dd31189845 > > > > > --- /dev/null > > > > > +++ b/include/configs/imx8qxp_ai_ml.h > > > > > @@ -0,0 +1,104 @@ > > > > > +/* SPDX-License-Identifier: GPL-2.0+ */ > > > > > +/* > > > > > + * Copyright 2018 NXP > > > > > + * Copyright 2019 Linaro Ltd. > > > > > + */ > > > > > + > > > > > +#ifndef __IMX8QXP_AI_ML_H > > > > > +#define __IMX8QXP_AI_ML_H > > > > > + > > > > > +#include <linux/sizes.h> > > > > > +#include <asm/arch/imx-regs.h> > > > > > + > > > > > +#ifdef CONFIG_SPL_BUILD > > > > > +#define CONFIG_SPL_MAX_SIZE > > > > > (124 * 1024) +#define CONFIG_SYS_MONITOR_LEN > > > > > (1024 * 1024) +#define > > > > > CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR +#define > > > > > CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x250 +#define > > > > > CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0 + > > > > > +#define > > > > > CONFIG_SPL_LDSCRIPT > > > > > "arch/arm/cpu/armv8/u-boot-spl.lds" +#define > > > > > CONFIG_SPL_STACK 0x013E000 +#define > > > > > CONFIG_SPL_BSS_START_ADDR 0x00128000 +#define > > > > > CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB > > > > > */ +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000 > > > > > +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* > > > > > 12 KB */ +#define CONFIG_SERIAL_LPUART_BASE 0x5a080000 > > > > > +#define CONFIG_MALLOC_F_ADDR 0x00120000 + > > > > > +#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE + > > > > > +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE > > > > > + > > > > > +#define CONFIG_OF_EMBED > > > > > > > > I'm not sure if the OF_EMBED is not deprecated ... and replaced > > > > by OF_SEPARATED. > > > > > > > > > > I'm not sure about this. I don't see any such information. > > > > There was a u-boot ML discussion about OF_EMBED deprecation. > > https://patchwork.ozlabs.org/project/uboot/list/?series=&submitter=&state=*&q=OF_EMBED&archive=both&delegate= > > > > Also please see: > > https://www.chromium.org/developers/u-boot > > > > Okay, thanks for the pointer. > > > > > > > > > +#endif > > > > > + > > > > > +#define CONFIG_REMAKE_ELF > > > > > + > > > > > +#define CONFIG_BOARD_EARLY_INIT_F > > > > > > > > This could be set in Kconfig, IIRC > > > > > > > > > > Ack. > > > > > > > > + > > > > > +/* Flat Device Tree Definitions */ > > > > > +#define CONFIG_OF_BOARD_SETUP > > > > > + > > > > > +#define CONFIG_FSL_USDHC > > > > > + > > > > > +#define CONFIG_ENV_OVERWRITE > > > > > + > > > > > +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG > > > > > + > > > > > +#define BOOT_TARGET_DEVICES(func) \ > > > > > + func(MMC, mmc, 1) \ > > > > > + func(DHCP, dhcp, na) > > > > > + > > > > > +#include <config_distro_bootcmd.h> > > > > > +/* Initial environment variables */ > > > > > +#define CONFIG_EXTRA_ENV_SETTINGS > > > > > \ > > > > > + "console=ttyLP2 earlycon\0" \ > > > > > + "fdt_addr_r=0x83000000\0" \ > > > > > + "kernel_addr_r=0x81000000\0" \ > > > > > + "ramdisk_addr_r=0x94400000\0" \ > > > > > + "scriptaddr=0x89000000\0" \ > > > > > + "fdtfile=imx8qxp-ai_ml.dtb\0" \ > > > > > + "fdt_high=0xffffffffffffffff\0" \ > > > > > + "image=Image\0" \ > > > > > + "initrd_addr=0x83800000\0" \ > > > > > + "initrd_high=0xffffffffffffffff\0" \ > > > > > + "netargs=setenv bootargs > > > > > console=${console},${baudrate} " \ > > > > > + "root=/dev/nfs ip=dhcp > > > > > nfsroot=${serverip}:${nfsroot},v3,tcp" \ > > > > > + "\0" \ > > > > > + "nfsboot=run netargs; dhcp ${loadaddr} ${image}; tftp > > > > > ${fdt_addr} " \ > > > > > + "imx8qxp-ai_ml/${fdt_file}; booti > > > > > ${loadaddr} - ${fdt_addr}\0" \ > > > > > + BOOTENV > > > > > + > > > > > +/* Link Definitions */ > > > > > +#define CONFIG_LOADADDR 0x80280000 > > > > > + > > > > > +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR > > > > > + > > > > > +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000 > > > > > + > > > > > +/* Default environment is in SD */ > > > > > +#define CONFIG_ENV_SIZE 0x1000 > > > > > +#define CONFIG_ENV_OFFSET (64 * SZ_64K) > > > > > + > > > > > +/* USDHC2 is the SD card interface */ > > > > > +#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 > > > > > */ +#define CONFIG_SYS_FSL_USDHC_NUM 2 > > > > > + > > > > > > > > Some of those env setting defines as well as eMMC ones could be > > > > set now in Kconfig. > > > > > > > > > > Can you please specify those? I don't see these defines used in > > > Kconfig. > > > > The best (and simplest) way is to just check if the corresponding > > CONFIG_* option is already moved (ported) to Kconfig. For > > example ENV_SIZE and ENV_OFFSET are. > > > > Yeah, I see it now that couple of boards are using it. Will do the > same. > > Thanks, > Mani > > > > > > > > > +/* Size of malloc() pool */ > > > > > +#define CONFIG_SYS_MALLOC_LEN > > > > > ((CONFIG_ENV_SIZE + (32 > > > > > * 1024)) * 1024) + > > > > > +#define CONFIG_SYS_SDRAM_BASE 0x80000000 > > > > > +#define PHYS_SDRAM_1 0x80000000 > > > > > +#define PHYS_SDRAM_2 0x880000000 > > > > > +#define PHYS_SDRAM_1_SIZE SZ_2G > > > > > /* 2 > > > > > > > > Please fix this file globally, to use "SZ_XX" instead of magic > > > > numbers. > > > > > > Ack. > > > > > > Thanks, > > > Mani > > > > > > > > GB */ +#define PHYS_SDRAM_2_SIZE 0x00000000 > > > > > /* 0 GB */ + > > > > > +/* Generic Timer Definitions */ > > > > > +#define COUNTER_FREQUENCY 8000000 /* > > > > > 8MHz */ + > > > > > +/* Networking */ > > > > > +#define CONFIG_FEC_XCV_TYPE RGMII > > > > > +#define FEC_QUIRK_ENET_MAC > > > > > + > > > > > +#endif /* __IMX8QXP_AI_ML_H */ > > > > > > > > > > > > > > > > > > > > Best regards, > > > > > > > > Lukasz Majewski > > > > > > > > -- > > > > > > > > DENX Software Engineering GmbH, Managing Director: Wolfgang > > > > Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 > > > > Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax: > > > > (+49)-8142-66989-80 Email: lukma@denx.de > > > > > > > > > > > > > > Best regards, > > > > Lukasz Majewski > > > > -- > > > > DENX Software Engineering GmbH, Managing Director: Wolfgang > > Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, > > Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: > > lukma@denx.de > > Best regards, Lukasz Majewski -- DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de
diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig index bbe323d5ca..cec21f8dd2 100644 --- a/arch/arm/mach-imx/imx8/Kconfig +++ b/arch/arm/mach-imx/imx8/Kconfig @@ -37,6 +37,11 @@ config TARGET_COLIBRI_IMX8X select BOARD_LATE_INIT select IMX8QXP +config TARGET_IMX8QXP_AI_ML + bool "Support i.MX8QXP AI_ML board" + select BOARD_LATE_INIT + select IMX8QXP + config TARGET_IMX8QM_MEK bool "Support i.MX8QM MEK board" select BOARD_LATE_INIT @@ -49,6 +54,7 @@ config TARGET_IMX8QXP_MEK endchoice +source "board/einfochips/imx8qxp_ai_ml/Kconfig" source "board/freescale/imx8qm_mek/Kconfig" source "board/freescale/imx8qxp_mek/Kconfig" source "board/toradex/apalis-imx8/Kconfig" diff --git a/board/einfochips/imx8qxp_ai_ml/Kconfig b/board/einfochips/imx8qxp_ai_ml/Kconfig new file mode 100644 index 0000000000..697a831013 --- /dev/null +++ b/board/einfochips/imx8qxp_ai_ml/Kconfig @@ -0,0 +1,12 @@ +if TARGET_IMX8QXP_AI_ML + +config SYS_BOARD + default "imx8qxp_ai_ml" + +config SYS_VENDOR + default "einfochips" + +config SYS_CONFIG_NAME + default "imx8qxp_ai_ml" + +endif diff --git a/board/einfochips/imx8qxp_ai_ml/MAINTAINERS b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS new file mode 100644 index 0000000000..add0bd9431 --- /dev/null +++ b/board/einfochips/imx8qxp_ai_ml/MAINTAINERS @@ -0,0 +1,6 @@ +i.MX8QXP AI_ML BOARD +M: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> +S: Maintained +F: board/einfochips/imx8qxp_ai_ml/ +F: include/configs/imx8qxp_ai_ml.h +F: configs/imx8qxp_ai_ml_defconfig diff --git a/board/einfochips/imx8qxp_ai_ml/Makefile b/board/einfochips/imx8qxp_ai_ml/Makefile new file mode 100644 index 0000000000..e08774dc6e --- /dev/null +++ b/board/einfochips/imx8qxp_ai_ml/Makefile @@ -0,0 +1,8 @@ +# +# Copyright 2019 Linaro Ltd. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += imx8qxp_ai_ml.o +obj-$(CONFIG_SPL_BUILD) += spl.o diff --git a/board/einfochips/imx8qxp_ai_ml/README b/board/einfochips/imx8qxp_ai_ml/README new file mode 100644 index 0000000000..488920580f --- /dev/null +++ b/board/einfochips/imx8qxp_ai_ml/README @@ -0,0 +1,49 @@ +U-Boot for the Einfochips i.MX8QXP AI_ML board + +Quick Start +=========== + +- Get and Build the ARM Trusted firmware +- Get scfw_tcm.bin and ahab-container.img +- Build U-Boot +- Flash the binary into the SD card +- Boot + +Get and Build the ARM Trusted firmware +====================================== + +$ git clone https://source.codeaurora.org/external/imx/imx-atf +$ cd imx-atf/ +$ git checkout origin/imx_4.9.88_imx8qxp_beta2 -b imx_4.9.88_imx8qxp_beta2 +$ make PLAT=imx8qxp bl31 + +Get scfw_tcm.bin and ahab-container.img +======================================= + +$ wget https://raw.githubusercontent.com/96boards-ai-ml/binaries/master/mx8qx-aiml-scfw-tcm.bin +$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.1.bin +$ chmod +x firmware-imx-8.1.bin +$ ./firmware-imx-8.1.bin + +Copy the following binaries to U-Boot folder: + +$ cp imx-atf/build/imx8qxp/release/bl31.bin . +$ cp firmware-imx-8.1/firmware/seco/mx8qx-ahab-container.img . + +Build U-Boot +============ + +$ make imx8qxp_ai_ml_defconfig +$ make u-boot-dtb.imx + +Flash the binary into the SD card +================================= + +Burn the u-boot-dtb.imx binary to SD card offset 32KB: + +$ sudo dd if=u-boot-dtb.imx of=/dev/sd[x] bs=1024 seek=32 + +Boot +==== + +Set Boot switch SW2: 1100. diff --git a/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c new file mode 100644 index 0000000000..e7632524a0 --- /dev/null +++ b/board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c @@ -0,0 +1,117 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + * Copyright 2019 Linaro Ltd. + */ + +#include <common.h> +#include <errno.h> +#include <linux/libfdt.h> +#include <environment.h> +#include <fsl_esdhc.h> +#include <asm/io.h> +#include <asm/arch/clock.h> +#include <asm/arch/sci/sci.h> +#include <asm/arch/imx8-pins.h> +#include <asm/arch/iomux.h> +#include <asm/arch/sys_proto.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \ + (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \ + (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \ + (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT)) + +static iomux_cfg_t uart2_pads[] = { + SC_P_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL), + SC_P_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx8_iomux_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); +} + +int board_early_init_f(void) +{ + sc_pm_clock_rate_t rate = SC_80MHZ; + int ret; + + /* Set UART2 clock root to 80 MHz */ + ret = sc_pm_setup_uart(SC_R_UART_2, rate); + if (ret) + return ret; + + setup_iomux_uart(); + + return 0; +} + +#if IS_ENABLED(CONFIG_DM_GPIO) +static void board_gpio_init(void) +{ + /* TODO */ +} +#else +static inline void board_gpio_init(void) {} +#endif + +#if IS_ENABLED(CONFIG_FEC_MXC) +#include <miiphy.h> + +int board_phy_config(struct phy_device *phydev) +{ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); + + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} +#endif + +int checkboard(void) +{ + puts("Board: iMX8QXP AI_ML\n"); + + build_info(); + print_bootinfo(); + + return 0; +} + +int board_init(void) +{ + board_gpio_init(); + + return 0; +} + +/* Board specific reset that is system reset */ + +void reset_cpu(ulong addr) +{ + /* TODO */ +} + +#ifdef CONFIG_OF_BOARD_SETUP +int ft_board_setup(void *blob, bd_t *bd) +{ + return 0; +} +#endif + +int board_mmc_get_env_dev(int devno) +{ + return devno; +} + +int board_late_init(void) +{ + return 0; +} diff --git a/board/einfochips/imx8qxp_ai_ml/imximage.cfg b/board/einfochips/imx8qxp_ai_ml/imximage.cfg new file mode 100644 index 0000000000..4fc5ade313 --- /dev/null +++ b/board/einfochips/imx8qxp_ai_ml/imximage.cfg @@ -0,0 +1,24 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + * + * Refer doc/README.imx8image for more details about how-to configure + * and create imx8image boot image + */ + +#define __ASSEMBLY__ + +/* Boot from SD, sector size 0x400 */ +BOOT_FROM SD 0x400 +/* SoC type IMX8QX */ +SOC_TYPE IMX8QX +/* Append seco container image */ +APPEND mx8qx-ahab-container.img +/* Create the 2nd container */ +CONTAINER +/* Add scfw image with exec attribute */ +IMAGE SCU mx8qx-aiml-scfw-tcm.bin +/* Add ATF image with exec attribute */ +IMAGE A35 bl31.bin 0x80000000 +/* Add U-Boot image with load attribute */ +DATA A35 u-boot-dtb.bin 0x80020000 diff --git a/board/einfochips/imx8qxp_ai_ml/spl.c b/board/einfochips/imx8qxp_ai_ml/spl.c new file mode 100644 index 0000000000..63581eeaaf --- /dev/null +++ b/board/einfochips/imx8qxp_ai_ml/spl.c @@ -0,0 +1,49 @@ +/* + * Copyright 2018 NXP + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <dm.h> +#include <spl.h> +#include <dm/uclass.h> +#include <dm/device.h> +#include <dm/uclass-internal.h> +#include <dm/device-internal.h> +#include <dm/lists.h> + +DECLARE_GLOBAL_DATA_PTR; + +void spl_board_init(void) +{ + struct udevice *dev; + + uclass_find_first_device(UCLASS_MISC, &dev); + + for (; dev; uclass_find_next_device(&dev)) { + if (device_probe(dev)) + continue; + } + + arch_cpu_init(); + + board_early_init_f(); + + timer_init(); + + preloader_console_init(); + + puts("Normal Boot\n"); +} + +void board_init_f(ulong dummy) +{ + /* Clear global data */ + memset((void *)gd, 0, sizeof(gd_t)); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + board_init_r(NULL, 0); +} diff --git a/configs/imx8qxp_ai_ml_defconfig b/configs/imx8qxp_ai_ml_defconfig new file mode 100644 index 0000000000..e20a0c783e --- /dev/null +++ b/configs/imx8qxp_ai_ml_defconfig @@ -0,0 +1,83 @@ +CONFIG_ARM=y +CONFIG_ARCH_IMX8=y +CONFIG_SYS_TEXT_BASE=0x80020000 +CONFIG_DISTRO_DEFAULTS=y +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SYS_MALLOC_F_LEN=0x4000 +CONFIG_TARGET_IMX8QXP_AI_ML=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=4 +CONFIG_SPL=y +CONFIG_FIT=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/einfochips/imx8qxp_ai_ml/imximage.cfg" +CONFIG_BOOTDELAY=3 +CONFIG_LOG=y +CONFIG_SPL_BOARD_INIT=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SPL_POWER_SUPPORT=y +CONFIG_SPL_POWER_DOMAIN=y +CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_HUSH_PARSER=y +CONFIG_CMD_CPU=y +# CONFIG_CMD_IMPORTENV is not set +CONFIG_CMD_CLK=y +CONFIG_CMD_DM=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FAT=y +CONFIG_FAT_WRITE=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qxp-ai_ml" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SPL_DM=y +CONFIG_SPL_CLK=y +CONFIG_CLK_IMX8=y +CONFIG_CPU=y +CONFIG_DM_GPIO=y +CONFIG_MXC_GPIO=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_IMX_LPI2C=y +CONFIG_MISC=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_PHYLIB=y +CONFIG_PHY_ADDR_ENABLE=y +CONFIG_PHY_ATHEROS=y +CONFIG_DM_ETH=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_PHY_GIGE=y +CONFIG_FEC_MXC_SHARE_MDIO=y +CONFIG_FEC_MXC_MDIO_BASE=0x5B040000 +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +CONFIG_PINCTRL_IMX8=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8_POWER_DOMAIN=y +CONFIG_DM_REGULATOR=y +CONFIG_SPL_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_SPL_DM_REGULATOR_GPIO=y +CONFIG_DM_SERIAL=y +CONFIG_FSL_LPUART=y +CONFIG_SPL_TINY_MEMSET=y +# CONFIG_EFI_LOADER is not set diff --git a/include/configs/imx8qxp_ai_ml.h b/include/configs/imx8qxp_ai_ml.h new file mode 100644 index 0000000000..dd31189845 --- /dev/null +++ b/include/configs/imx8qxp_ai_ml.h @@ -0,0 +1,104 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + * Copyright 2019 Linaro Ltd. + */ + +#ifndef __IMX8QXP_AI_ML_H +#define __IMX8QXP_AI_ML_H + +#include <linux/sizes.h> +#include <asm/arch/imx-regs.h> + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_MAX_SIZE (124 * 1024) +#define CONFIG_SYS_MONITOR_LEN (1024 * 1024) +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x250 +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0 + +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" +#define CONFIG_SPL_STACK 0x013E000 +#define CONFIG_SPL_BSS_START_ADDR 0x00128000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */ +#define CONFIG_SYS_SPL_MALLOC_START 0x00120000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */ +#define CONFIG_SERIAL_LPUART_BASE 0x5a080000 +#define CONFIG_MALLOC_F_ADDR 0x00120000 + +#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE + +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE + +#define CONFIG_OF_EMBED +#endif + +#define CONFIG_REMAKE_ELF + +#define CONFIG_BOARD_EARLY_INIT_F + +/* Flat Device Tree Definitions */ +#define CONFIG_OF_BOARD_SETUP + +#define CONFIG_FSL_USDHC + +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + +#define BOOT_TARGET_DEVICES(func) \ + func(MMC, mmc, 1) \ + func(DHCP, dhcp, na) + +#include <config_distro_bootcmd.h> +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "console=ttyLP2 earlycon\0" \ + "fdt_addr_r=0x83000000\0" \ + "kernel_addr_r=0x81000000\0" \ + "ramdisk_addr_r=0x94400000\0" \ + "scriptaddr=0x89000000\0" \ + "fdtfile=imx8qxp-ai_ml.dtb\0" \ + "fdt_high=0xffffffffffffffff\0" \ + "image=Image\0" \ + "initrd_addr=0x83800000\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp" \ + "\0" \ + "nfsboot=run netargs; dhcp ${loadaddr} ${image}; tftp ${fdt_addr} " \ + "imx8qxp-ai_ml/${fdt_file}; booti ${loadaddr} - ${fdt_addr}\0" \ + BOOTENV + +/* Link Definitions */ +#define CONFIG_LOADADDR 0x80280000 + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +#define CONFIG_SYS_INIT_SP_ADDR 0x80200000 + +/* Default environment is in SD */ +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_ENV_OFFSET (64 * SZ_64K) + +/* USDHC2 is the SD card interface */ +#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */ +#define CONFIG_SYS_FSL_USDHC_NUM 2 + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 * 1024)) * 1024) + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define PHYS_SDRAM_1 0x80000000 +#define PHYS_SDRAM_2 0x880000000 +#define PHYS_SDRAM_1_SIZE SZ_2G /* 2 GB */ +#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 GB */ + +/* Generic Timer Definitions */ +#define COUNTER_FREQUENCY 8000000 /* 8MHz */ + +/* Networking */ +#define CONFIG_FEC_XCV_TYPE RGMII +#define FEC_QUIRK_ENET_MAC + +#endif /* __IMX8QXP_AI_ML_H */
This commit adds initial board support for iMX8QXP AI_ML board from Einfochips. This board is one of the 96Boards Consumer Edition and AI boards of the 96Boards family based on i.MX8QXP SoC from NXP/Freescale. This initial supports contains following peripherals which are tested and known to work: 1. Debug serial via UART2 2. SD card 3. Ethernet More information about this board can be found in arrow website: https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- arch/arm/mach-imx/imx8/Kconfig | 6 + board/einfochips/imx8qxp_ai_ml/Kconfig | 12 ++ board/einfochips/imx8qxp_ai_ml/MAINTAINERS | 6 + board/einfochips/imx8qxp_ai_ml/Makefile | 8 ++ board/einfochips/imx8qxp_ai_ml/README | 49 ++++++++ .../einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c | 117 ++++++++++++++++++ board/einfochips/imx8qxp_ai_ml/imximage.cfg | 24 ++++ board/einfochips/imx8qxp_ai_ml/spl.c | 49 ++++++++ configs/imx8qxp_ai_ml_defconfig | 83 +++++++++++++ include/configs/imx8qxp_ai_ml.h | 104 ++++++++++++++++ 10 files changed, 458 insertions(+) create mode 100644 board/einfochips/imx8qxp_ai_ml/Kconfig create mode 100644 board/einfochips/imx8qxp_ai_ml/MAINTAINERS create mode 100644 board/einfochips/imx8qxp_ai_ml/Makefile create mode 100644 board/einfochips/imx8qxp_ai_ml/README create mode 100644 board/einfochips/imx8qxp_ai_ml/imx8qxp_ai_ml.c create mode 100644 board/einfochips/imx8qxp_ai_ml/imximage.cfg create mode 100644 board/einfochips/imx8qxp_ai_ml/spl.c create mode 100644 configs/imx8qxp_ai_ml_defconfig create mode 100644 include/configs/imx8qxp_ai_ml.h