[v2] arm: dts: mediatek: add basic support for MT7629 SoC

From: Ryder Lee <ryder.lee@mediatek.com>

This adds basic support for MT7629 reference board.

Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
---
Changes since v2:
- fix 'no newline at end of file'.
- fix addresses/sizes cells.
- update u3phy0 node.
- add eth/pcie related nodes.
- add the 'fixed-partitions' nodes in flash node.
- remove arm,cpu-registers-not-fw-configured.

Changes since v1:
-Fix unit-address warnings.
-Put all the mmio peripherals under a simple-bus node.
-Drop all the 'partitions' nodes in flash node.
---
 arch/arm/boot/dts/Makefile                |   1 +
 arch/arm/boot/dts/mt7629-rfb.dts          | 263 ++++++++++++
 arch/arm/boot/dts/mt7629.dtsi             | 481 ++++++++++++++++++++++
 include/dt-bindings/reset/mt7629-resets.h |  71 ++++
 4 files changed, 816 insertions(+)
 create mode 100644 arch/arm/boot/dts/mt7629-rfb.dts
 create mode 100644 arch/arm/boot/dts/mt7629.dtsi
 create mode 100644 include/dt-bindings/reset/mt7629-resets.h

On 11/07/2019 04:14, ryder.lee@kernel.org wrote:
> From: Ryder Lee <ryder.lee@mediatek.com>
> 
> This adds basic support for MT7629 reference board.
> 
> Tested-by: Kevin Hilman <khilman@baylibre.com>
> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>

applied to v5.3-next/dts32

Thanks!

> ---
> Changes since v2:
> - fix 'no newline at end of file'.
> - fix addresses/sizes cells.
> - update u3phy0 node.
> - add eth/pcie related nodes.
> - add the 'fixed-partitions' nodes in flash node.
> - remove arm,cpu-registers-not-fw-configured.
> 
> Changes since v1:
> -Fix unit-address warnings.
> -Put all the mmio peripherals under a simple-bus node.
> -Drop all the 'partitions' nodes in flash node.
> ---
>  arch/arm/boot/dts/Makefile                |   1 +
>  arch/arm/boot/dts/mt7629-rfb.dts          | 263 ++++++++++++
>  arch/arm/boot/dts/mt7629.dtsi             | 481 ++++++++++++++++++++++
>  include/dt-bindings/reset/mt7629-resets.h |  71 ++++
>  4 files changed, 816 insertions(+)
>  create mode 100644 arch/arm/boot/dts/mt7629-rfb.dts
>  create mode 100644 arch/arm/boot/dts/mt7629.dtsi
>  create mode 100644 include/dt-bindings/reset/mt7629-resets.h
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index dab2914fa293..080784da8ae1 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1258,6 +1258,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
>  	mt7623a-rfb-nand.dtb \
>  	mt7623n-rfb-emmc.dtb \
>  	mt7623n-bananapi-bpi-r2.dtb \
> +	mt7629-rfb.dtb \
>  	mt8127-moose.dtb \
>  	mt8135-evbp1.dtb
>  dtb-$(CONFIG_ARCH_MILBEAUT) += milbeaut-m10v-evb.dtb
> diff --git a/arch/arm/boot/dts/mt7629-rfb.dts b/arch/arm/boot/dts/mt7629-rfb.dts
> new file mode 100644
> index 000000000000..3621b7d2b22a
> --- /dev/null
> +++ b/arch/arm/boot/dts/mt7629-rfb.dts
> @@ -0,0 +1,263 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019 MediaTek Inc.
> + * Author: Ryder Lee <ryder.lee@mediatek.com>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/input/input.h>
> +#include "mt7629.dtsi"
> +
> +/ {
> +	model = "MediaTek MT7629 reference board";
> +	compatible = "mediatek,mt7629-rfb", "mediatek,mt7629";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		reset {
> +			label = "factory";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&pio 60 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		wps {
> +			label = "wps";
> +			linux,code = <KEY_WPS_BUTTON>;
> +			gpios = <&pio 58 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	memory@40000000 {
> +		device_type = "memory";
> +		reg = <0x40000000 0x10000000>;
> +	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-3.3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	reg_5v: regulator-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +};
> +
> +&eth {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&eth_pins>;
> +	pinctrl-1 = <&ephy_leds_pins>;
> +	status = "okay";
> +
> +	gmac1: mac@1 {
> +		compatible = "mediatek,eth-mac";
> +		reg = <1>;
> +		phy-handle = <&phy0>;
> +	};
> +
> +	mdio: mdio-bus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		phy0: ethernet-phy@0 {
> +			reg = <0>;
> +			phy-mode = "gmii";
> +		};
> +	};
> +};
> +
> +&i2c {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c_pins>;
> +	status = "okay";
> +};
> +
> +&qspi {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&qspi_pins>;
> +	status = "okay";
> +
> +	flash@0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			partition@0 {
> +				label = "u-boot";
> +				reg = <0x00000 0x60000>;
> +				read-only;
> +			};
> +
> +			partition@60000 {
> +				label = "u-boot-env";
> +				reg = <0x60000 0x10000>;
> +				read-only;
> +			};
> +
> +			factory: partition@70000 {
> +				label = "factory";
> +				reg = <0x70000 0x40000>;
> +				read-only;
> +			};
> +
> +			partition@b0000 {
> +				label = "kernel";
> +				reg = <0xb0000 0xb50000>;
> +			};
> +		};
> +	};
> +};
> +
> +&pcie {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie_pins>;
> +};
> +
> +&pciephy1 {
> +	status = "okay";
> +};
> +
> +&pio {
> +	eth_pins: eth-pins {
> +		mux {
> +			function = "eth";
> +			groups = "mdc_mdio";
> +		};
> +	};
> +
> +	ephy_leds_pins: ephy-leds-pins {
> +		mux {
> +			function = "led";
> +			groups = "gphy_leds_0", "ephy_leds";
> +		};
> +	};
> +
> +	i2c_pins: i2c-pins {
> +		mux {
> +			function = "i2c";
> +			groups =  "i2c_0";
> +		};
> +
> +		conf {
> +			pins = "I2C_SDA", "I2C_SCL";
> +			drive-strength = <4>;
> +			bias-disable;
> +		};
> +	};
> +
> +	pcie_pins: pcie-pins {
> +		mux {
> +			function = "pcie";
> +			groups = "pcie_clkreq",
> +				 "pcie_pereset",
> +				 "pcie_wake";
> +		};
> +	};
> +
> +	pwm_pins: pwm-pins {
> +		mux {
> +			function = "pwm";
> +			groups = "pwm_0";
> +		};
> +	};
> +
> +	/* SPI-NOR is shared pin with serial NAND */
> +	qspi_pins: qspi-pins {
> +		mux {
> +			function = "flash";
> +			groups = "spi_nor";
> +		};
> +	};
> +
> +	/* Serial NAND is shared pin with SPI-NOR */
> +	serial_nand_pins: serial-nand-pins {
> +		mux {
> +			function = "flash";
> +			groups = "snfi";
> +		};
> +	};
> +
> +	spi_pins: spi-pins {
> +		mux {
> +			function = "spi";
> +			groups = "spi_0";
> +		};
> +	};
> +
> +	uart0_pins: uart0-pins {
> +		mux {
> +			function = "uart";
> +			groups = "uart0_txd_rxd" ;
> +		};
> +	};
> +
> +	uart1_pins: uart1-pins {
> +		mux {
> +			function = "uart";
> +			groups = "uart1_0_tx_rx" ;
> +		};
> +	};
> +
> +	uart2_pins: uart2-pins {
> +		mux {
> +			function = "uart";
> +			groups = "uart2_0_txd_rxd" ;
> +		};
> +	};
> +
> +	watchdog_pins: watchdog-pins {
> +		mux {
> +			function = "watchdog";
> +			groups = "watchdog";
> +		};
> +	};
> +};
> +
> +&spi {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi_pins>;
> +	status = "okay";
> +};
> +
> +&ssusb {
> +	vusb33-supply = <&reg_3p3v>;
> +	vbus-supply = <&reg_5v>;
> +	status = "okay";
> +};
> +
> +&u3phy0 {
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins>;
> +	status = "okay";
> +};
> +
> +&watchdog {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&watchdog_pins>;
> +	status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/mt7629.dtsi b/arch/arm/boot/dts/mt7629.dtsi
> new file mode 100644
> index 000000000000..9608bc2ccb3f
> --- /dev/null
> +++ b/arch/arm/boot/dts/mt7629.dtsi
> @@ -0,0 +1,481 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019 MediaTek Inc.
> + *
> + * Author: Ryder Lee <ryder.lee@mediatek.com>
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/mt7629-clk.h>
> +#include <dt-bindings/power/mt7622-power.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/reset/mt7629-resets.h>
> +
> +/ {
> +	compatible = "mediatek,mt7629";
> +	interrupt-parent = <&sysirq>;
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		enable-method = "mediatek,mt6589-smp";
> +
> +		cpu0: cpu@0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a7";
> +			reg = <0x0>;
> +			clock-frequency = <1250000000>;
> +			cci-control-port = <&cci_control2>;
> +		};
> +
> +		cpu1: cpu@1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a7";
> +			reg = <0x1>;
> +			clock-frequency = <1250000000>;
> +			cci-control-port = <&cci_control2>;
> +		};
> +	};
> +
> +	pmu {
> +		compatible = "arm,cortex-a7-pmu";
> +		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 9 IRQ_TYPE_LEVEL_LOW>;
> +		interrupt-affinity = <&cpu0>, <&cpu1>;
> +	};
> +
> +	clk20m: oscillator-0 {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <20000000>;
> +		clock-output-names = "clk20m";
> +	};
> +
> +	clk40m: oscillator-1 {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <40000000>;
> +		clock-output-names = "clkxtal";
> +	};
> +
> +	timer {
> +		compatible = "arm,armv7-timer";
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> +			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +		clock-frequency = <20000000>;
> +	};
> +
> +	soc {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		infracfg: syscon@10000000 {
> +			compatible = "mediatek,mt7629-infracfg", "syscon";
> +			reg = <0x10000000 0x1000>;
> +			#clock-cells = <1>;
> +		};
> +
> +		pericfg: syscon@10002000 {
> +			compatible = "mediatek,mt7629-pericfg", "syscon";
> +			reg = <0x10002000 0x1000>;
> +			#clock-cells = <1>;
> +		};
> +
> +		scpsys: scpsys@10006000 {
> +			compatible = "mediatek,mt7629-scpsys",
> +				     "mediatek,mt7622-scpsys";
> +			#power-domain-cells = <1>;
> +			reg = <0x10006000 0x1000>;
> +			clocks = <&topckgen CLK_TOP_HIF_SEL>;
> +			clock-names = "hif_sel";
> +			assigned-clocks = <&topckgen CLK_TOP_HIF_SEL>;
> +			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL1_D2>;
> +			infracfg = <&infracfg>;
> +		};
> +
> +		timer: timer@10009000 {
> +			compatible = "mediatek,mt7629-timer",
> +				     "mediatek,mt6765-timer";
> +			reg = <0x10009000 0x60>;
> +			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&clk20m>;
> +			clock-names = "clk20m";
> +		};
> +
> +		sysirq: interrupt-controller@10200a80 {
> +			compatible = "mediatek,mt7629-sysirq",
> +				     "mediatek,mt6577-sysirq";
> +			reg = <0x10200a80 0x20>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +		};
> +
> +		apmixedsys: syscon@10209000 {
> +			compatible = "mediatek,mt7629-apmixedsys", "syscon";
> +			reg = <0x10209000 0x1000>;
> +			#clock-cells = <1>;
> +		};
> +
> +		rng: rng@1020f000 {
> +			compatible = "mediatek,mt7629-rng",
> +				     "mediatek,mt7623-rng";
> +			reg = <0x1020f000 0x100>;
> +			clocks = <&infracfg CLK_INFRA_TRNG_PD>;
> +			clock-names = "rng";
> +		};
> +
> +		topckgen: syscon@10210000 {
> +			compatible = "mediatek,mt7629-topckgen", "syscon";
> +			reg = <0x10210000 0x1000>;
> +			#clock-cells = <1>;
> +		};
> +
> +		watchdog: watchdog@10212000 {
> +			compatible = "mediatek,mt7629-wdt",
> +				     "mediatek,mt6589-wdt";
> +			reg = <0x10212000 0x100>;
> +		};
> +
> +		pio: pinctrl@10217000 {
> +			compatible = "mediatek,mt7629-pinctrl";
> +			reg = <0x10217000 0x8000>,
> +			      <0x10005000 0x1000>;
> +			reg-names = "base", "eint";
> +			gpio-controller;
> +			gpio-ranges = <&pio 0 0 79>;
> +			#gpio-cells = <2>;
> +			#interrupt-cells = <2>;
> +			interrupt-controller;
> +			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-parent = <&gic>;
> +		};
> +
> +		gic: interrupt-controller@10300000 {
> +			compatible = "arm,gic-400";
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			reg = <0x10310000 0x1000>,
> +			      <0x10320000 0x1000>,
> +			      <0x10340000 0x2000>,
> +			      <0x10360000 0x2000>;
> +		};
> +
> +		cci: cci@10390000 {
> +			compatible = "arm,cci-400";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			reg = <0x10390000 0x1000>;
> +			ranges = <0 0x10390000 0x10000>;
> +
> +			cci_control0: slave-if@1000 {
> +				compatible = "arm,cci-400-ctrl-if";
> +				interface-type = "ace-lite";
> +				reg = <0x1000 0x1000>;
> +			};
> +
> +			cci_control1: slave-if@4000 {
> +				compatible = "arm,cci-400-ctrl-if";
> +				interface-type = "ace";
> +				reg = <0x4000 0x1000>;
> +			};
> +
> +			cci_control2: slave-if@5000 {
> +				compatible = "arm,cci-400-ctrl-if";
> +				interface-type = "ace";
> +				reg = <0x5000 0x1000>;
> +			};
> +
> +			pmu@9000 {
> +				compatible = "arm,cci-400-pmu,r1";
> +				reg = <0x9000 0x5000>;
> +				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> +			};
> +		};
> +
> +		uart0: serial@11002000 {
> +			compatible = "mediatek,mt7629-uart",
> +				     "mediatek,mt6577-uart";
> +			reg = <0x11002000 0x400>;
> +			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&topckgen CLK_TOP_UART_SEL>,
> +				 <&pericfg CLK_PERI_UART0_PD>;
> +			clock-names = "baud", "bus";
> +			status = "disabled";
> +		};
> +
> +		uart1: serial@11003000 {
> +			compatible = "mediatek,mt7629-uart",
> +				     "mediatek,mt6577-uart";
> +			reg = <0x11003000 0x400>;
> +			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&topckgen CLK_TOP_UART_SEL>,
> +				 <&pericfg CLK_PERI_UART1_PD>;
> +			clock-names = "baud", "bus";
> +			status = "disabled";
> +		};
> +
> +		uart2: serial@11004000 {
> +			compatible = "mediatek,mt7629-uart",
> +				     "mediatek,mt6577-uart";
> +			reg = <0x11004000 0x400>;
> +			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&topckgen CLK_TOP_UART_SEL>,
> +				 <&pericfg CLK_PERI_UART2_PD>;
> +			clock-names = "baud", "bus";
> +			status = "disabled";
> +		};
> +
> +		i2c: i2c@11007000 {
> +			compatible = "mediatek,mt7629-i2c",
> +				     "mediatek,mt2712-i2c";
> +			reg = <0x11007000 0x90>,
> +			      <0x11000100 0x80>;
> +			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_LOW>;
> +			clock-div = <4>;
> +			clocks = <&pericfg CLK_PERI_I2C0_PD>,
> +				 <&pericfg CLK_PERI_AP_DMA_PD>;
> +			clock-names = "main", "dma";
> +			assigned-clocks = <&topckgen CLK_TOP_AXI_SEL>;
> +			assigned-clock-parents = <&topckgen CLK_TOP_SYSPLL1_D2>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		spi: spi@1100a000 {
> +			compatible = "mediatek,mt7629-spi",
> +				     "mediatek,mt7622-spi";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x1100a000 0x100>;
> +			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&topckgen CLK_TOP_SYSPLL3_D2>,
> +				 <&topckgen CLK_TOP_SPI0_SEL>,
> +				 <&pericfg CLK_PERI_SPI0_PD>;
> +			clock-names = "parent-clk", "sel-clk", "spi-clk";
> +			status = "disabled";
> +		};
> +
> +		qspi: spi@11014000 {
> +			compatible = "mediatek,mt7629-nor",
> +				     "mediatek,mt8173-nor";
> +			reg = <0x11014000 0xe0>;
> +			clocks = <&pericfg CLK_PERI_FLASH_PD>,
> +				 <&topckgen CLK_TOP_FLASH_SEL>;
> +			clock-names = "spi", "sf";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		ssusbsys: syscon@1a000000 {
> +			compatible = "mediatek,mt7629-ssusbsys", "syscon";
> +			reg = <0x1a000000 0x1000>;
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +		};
> +
> +		ssusb: usb@1a0c0000 {
> +			compatible = "mediatek,mt7629-xhci",
> +				     "mediatek,mtk-xhci";
> +			reg = <0x1a0c0000 0x01000>,
> +			      <0x1a0c3e00 0x0100>;
> +			reg-names = "mac", "ippc";
> +			interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&ssusbsys CLK_SSUSB_SYS_EN>,
> +				 <&ssusbsys CLK_SSUSB_REF_EN>,
> +				 <&ssusbsys CLK_SSUSB_MCU_EN>,
> +				 <&ssusbsys CLK_SSUSB_DMA_EN>;
> +			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
> +			assigned-clocks = <&topckgen CLK_TOP_AXI_SEL>,
> +					  <&topckgen CLK_TOP_SATA_SEL>,
> +					  <&topckgen CLK_TOP_HIF_SEL>;
> +			assigned-clock-parents = <&topckgen CLK_TOP_SYSPLL1_D2>,
> +						 <&topckgen CLK_TOP_UNIVPLL2_D4>,
> +						 <&topckgen CLK_TOP_UNIVPLL1_D2>;
> +			power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF1>;
> +			phys = <&u2port0 PHY_TYPE_USB2>,
> +			       <&u3port0 PHY_TYPE_USB3>;
> +			status = "disabled";
> +		};
> +
> +		u3phy0: usb-phy@1a0c4000 {
> +			compatible = "mediatek,generic-tphy-v2";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0 0x1a0c4000 0xe00>;
> +			status = "disabled";
> +
> +			u2port0: usb-phy@0 {
> +				reg = <0 0x700>;
> +				clocks = <&ssusbsys CLK_SSUSB_U2_PHY_EN>;
> +				clock-names = "ref";
> +				#phy-cells = <1>;
> +				status = "okay";
> +			};
> +
> +			u3port0: usb-phy@700 {
> +				reg = <0x700 0x700>;
> +				clocks = <&clk20m>;
> +				clock-names = "ref";
> +				#phy-cells = <1>;
> +				status = "okay";
> +			};
> +		};
> +
> +		pciesys: syscon@1a100800 {
> +			compatible = "mediatek,mt7629-pciesys", "syscon";
> +			reg = <0x1a100800 0x1000>;
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +		};
> +
> +		pcie: pcie@1a140000 {
> +			compatible = "mediatek,mt7629-pcie";
> +			device_type = "pci";
> +			reg = <0x1a140000 0x1000>,
> +			      <0x1a145000 0x1000>;
> +			reg-names = "subsys","port1";
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&pciesys CLK_PCIE_P1_MAC_EN>,
> +				 <&pciesys CLK_PCIE_P0_AHB_EN>,
> +				 <&pciesys CLK_PCIE_P1_AUX_EN>,
> +				 <&pciesys CLK_PCIE_P1_AXI_EN>,
> +				 <&pciesys CLK_PCIE_P1_OBFF_EN>,
> +				 <&pciesys CLK_PCIE_P1_PIPE_EN>;
> +			clock-names = "sys_ck1", "ahb_ck1",
> +				      "aux_ck1", "axi_ck1",
> +				      "obff_ck1", "pipe_ck1";
> +			assigned-clocks = <&topckgen CLK_TOP_SATA_SEL>,
> +					  <&topckgen CLK_TOP_AXI_SEL>,
> +					  <&topckgen CLK_TOP_HIF_SEL>;
> +			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL2_D4>,
> +						 <&topckgen CLK_TOP_SYSPLL1_D2>,
> +						 <&topckgen CLK_TOP_UNIVPLL1_D2>;
> +			phys = <&pcieport1 PHY_TYPE_PCIE>;
> +			phy-names = "pcie-phy1";
> +			power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
> +			bus-range = <0x00 0xff>;
> +			ranges = <0x82000000 0 0x20000000 0x20000000 0 0x10000000>;
> +
> +			pcie1: pcie@1,0 {
> +				device_type = "pci";
> +				reg = <0x0800 0 0 0 0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				#interrupt-cells = <1>;
> +				ranges;
> +				num-lanes = <1>;
> +				interrupt-map-mask = <0 0 0 7>;
> +				interrupt-map = <0 0 0 1 &pcie_intc1 0>,
> +						<0 0 0 2 &pcie_intc1 1>,
> +						<0 0 0 3 &pcie_intc1 2>,
> +						<0 0 0 4 &pcie_intc1 3>;
> +
> +				pcie_intc1: interrupt-controller {
> +					interrupt-controller;
> +					#address-cells = <0>;
> +					#interrupt-cells = <1>;
> +				};
> +			};
> +		};
> +
> +		pciephy1: pcie-phy@1a14a000 {
> +			compatible = "mediatek,generic-tphy-v2";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0 0x1a14a000 0x1000>;
> +			status = "disabled";
> +
> +			pcieport1: port1phy@0 {
> +				reg = <0 0x1000>;
> +				clocks = <&clk20m>;
> +				clock-names = "ref";
> +				#phy-cells = <1>;
> +				status = "okay";
> +			};
> +		};
> +
> +		ethsys: syscon@1b000000 {
> +			compatible = "mediatek,mt7629-ethsys", "syscon";
> +			reg = <0x1b000000 0x1000>;
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +		};
> +
> +		eth: ethernet@1b100000 {
> +			compatible = "mediatek,mt7629-eth","syscon";
> +			reg = <0x1b100000 0x20000>;
> +			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 224 IRQ_TYPE_LEVEL_LOW>,
> +				     <GIC_SPI 225 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&topckgen CLK_TOP_ETH_SEL>,
> +				 <&topckgen CLK_TOP_F10M_REF_SEL>,
> +				 <&ethsys CLK_ETH_ESW_EN>,
> +				 <&ethsys CLK_ETH_GP0_EN>,
> +				 <&ethsys CLK_ETH_GP1_EN>,
> +				 <&ethsys CLK_ETH_GP2_EN>,
> +				 <&ethsys CLK_ETH_FE_EN>,
> +				 <&sgmiisys0 CLK_SGMII_TX_EN>,
> +				 <&sgmiisys0 CLK_SGMII_RX_EN>,
> +				 <&sgmiisys0 CLK_SGMII_CDR_REF>,
> +				 <&sgmiisys0 CLK_SGMII_CDR_FB>,
> +				 <&sgmiisys1 CLK_SGMII_TX_EN>,
> +				 <&sgmiisys1 CLK_SGMII_RX_EN>,
> +				 <&sgmiisys1 CLK_SGMII_CDR_REF>,
> +				 <&sgmiisys1 CLK_SGMII_CDR_FB>,
> +				 <&apmixedsys CLK_APMIXED_SGMIPLL>,
> +				 <&apmixedsys CLK_APMIXED_ETH2PLL>;
> +			clock-names = "ethif", "sgmiitop", "esw", "gp0", "gp1",
> +				      "gp2", "fe", "sgmii_tx250m", "sgmii_rx250m",
> +				      "sgmii_cdr_ref", "sgmii_cdr_fb",
> +				      "sgmii2_tx250m", "sgmii2_rx250m",
> +				      "sgmii2_cdr_ref", "sgmii2_cdr_fb",
> +				      "sgmii_ck", "eth2pll";
> +			assigned-clocks = <&topckgen CLK_TOP_ETH_SEL>,
> +					  <&topckgen CLK_TOP_F10M_REF_SEL>;
> +			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL1_D2>,
> +						 <&topckgen CLK_TOP_SGMIIPLL_D2>;
> +			power-domains = <&scpsys MT7622_POWER_DOMAIN_ETHSYS>;
> +			mediatek,ethsys = <&ethsys>;
> +			mediatek,sgmiisys = <&sgmiisys0>, <&sgmiisys1>;
> +			mediatek,infracfg = <&infracfg>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		sgmiisys0: syscon@1b128000 {
> +			compatible = "mediatek,mt7629-sgmiisys", "syscon";
> +			reg = <0x1b128000 0x3000>;
> +			#clock-cells = <1>;
> +			mediatek,physpeed = "2500";
> +		};
> +
> +		sgmiisys1: syscon@1b130000 {
> +			compatible = "mediatek,mt7629-sgmiisys", "syscon";
> +			reg = <0x1b130000 0x3000>;
> +			#clock-cells = <1>;
> +			mediatek,physpeed = "2500";
> +		};
> +	};
> +};
> diff --git a/include/dt-bindings/reset/mt7629-resets.h b/include/dt-bindings/reset/mt7629-resets.h
> new file mode 100644
> index 000000000000..6bb85734f68d
> --- /dev/null
> +++ b/include/dt-bindings/reset/mt7629-resets.h
> @@ -0,0 +1,71 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2019 MediaTek Inc.
> + */
> +
> +#ifndef _DT_BINDINGS_RESET_CONTROLLER_MT7629
> +#define _DT_BINDINGS_RESET_CONTROLLER_MT7629
> +
> +/* INFRACFG resets */
> +#define MT7629_INFRA_EMI_MPU_RST		0
> +#define MT7629_INFRA_UART5_RST			2
> +#define MT7629_INFRA_CIRQ_EINT_RST		3
> +#define MT7629_INFRA_APXGPT_RST			4
> +#define MT7629_INFRA_SCPSYS_RST			5
> +#define MT7629_INFRA_KP_RST			6
> +#define MT7629_INFRA_SPI1_RST			7
> +#define MT7629_INFRA_SPI4_RST			8
> +#define MT7629_INFRA_SYSTIMER_RST		9
> +#define MT7629_INFRA_IRRX_RST			10
> +#define MT7629_INFRA_AO_BUS_RST			16
> +#define MT7629_INFRA_EMI_RST			32
> +#define MT7629_INFRA_APMIXED_RST		35
> +#define MT7629_INFRA_MIPI_RST			36
> +#define MT7629_INFRA_TRNG_RST			37
> +#define MT7629_INFRA_SYSCIRQ_RST		38
> +#define MT7629_INFRA_MIPI_CSI_RST		39
> +#define MT7629_INFRA_GCE_FAXI_RST		40
> +#define MT7629_INFRA_I2C_SRAM_RST		41
> +#define MT7629_INFRA_IOMMU_RST			47
> +
> +/* PERICFG resets */
> +#define MT7629_PERI_UART0_SW_RST		0
> +#define MT7629_PERI_UART1_SW_RST		1
> +#define MT7629_PERI_UART2_SW_RST		2
> +#define MT7629_PERI_BTIF_SW_RST			6
> +#define MT7629_PERI_PWN_SW_RST			8
> +#define MT7629_PERI_DMA_SW_RST			11
> +#define MT7629_PERI_NFI_SW_RST			14
> +#define MT7629_PERI_I2C0_SW_RST			22
> +#define MT7629_PERI_SPI0_SW_RST			33
> +#define MT7629_PERI_SPI1_SW_RST			34
> +#define MT7629_PERI_FLASHIF_SW_RST		36
> +
> +/* PCIe Subsystem resets */
> +#define MT7629_PCIE1_CORE_RST			19
> +#define MT7629_PCIE1_MMIO_RST			20
> +#define MT7629_PCIE1_HRST			21
> +#define MT7629_PCIE1_USER_RST			22
> +#define MT7629_PCIE1_PIPE_RST			23
> +#define MT7629_PCIE0_CORE_RST			27
> +#define MT7629_PCIE0_MMIO_RST			28
> +#define MT7629_PCIE0_HRST			29
> +#define MT7629_PCIE0_USER_RST			30
> +#define MT7629_PCIE0_PIPE_RST			31
> +
> +/* SSUSB Subsystem resets */
> +#define MT7629_SSUSB_PHY_PWR_RST		3
> +#define MT7629_SSUSB_MAC_PWR_RST		4
> +
> +/* ETH Subsystem resets */
> +#define MT7629_ETHSYS_SYS_RST			0
> +#define MT7629_ETHSYS_MCM_RST			2
> +#define MT7629_ETHSYS_HSDMA_RST			5
> +#define MT7629_ETHSYS_FE_RST			6
> +#define MT7629_ETHSYS_ESW_RST			16
> +#define MT7629_ETHSYS_GMAC_RST			23
> +#define MT7629_ETHSYS_EPHY_RST			24
> +#define MT7629_ETHSYS_CRYPTO_RST		29
> +#define MT7629_ETHSYS_PPE_RST			31
> +
> +#endif  /* _DT_BINDINGS_RESET_CONTROLLER_MT7629 */
>