new file mode 100644
@@ -0,0 +1,50 @@
+#
+# Copyright (C) ST-Ericsson SA 2009
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+CFLAGS += -D__RELEASE -D__STN_8500
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := u8500_href.o gpio.o prcmu.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
new file mode 100644
@@ -0,0 +1,347 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2009
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/gpio.h>
+
+static struct gpio_register *addr_gpio_register[] = {
+ (void *)U8500_GPIO_0_BASE,
+ (void *)U8500_GPIO_1_BASE,
+ (void *)U8500_GPIO_2_BASE,
+ (void *)U8500_GPIO_3_BASE,
+ (void *)U8500_GPIO_4_BASE,
+ (void *)U8500_GPIO_5_BASE,
+ (void *)U8500_GPIO_6_BASE,
+ (void *)U8500_GPIO_7_BASE,
+ (void *)U8500_GPIO_8_BASE,
+};
+
+struct gpio_altfun_data altfun_table[] = {
+ {
+ .altfun = GPIO_ALT_I2C_0,
+ .start = 147,
+ .end = 148,
+ .cont = 0,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_I2C_1,
+ .start = 16,
+ .end = 17,
+ .cont = 0,
+ .type = GPIO_ALTF_B,
+ },
+ {
+ .altfun = GPIO_ALT_I2C_2,
+ .start = 10,
+ .end = 11,
+ .cont = 0,
+ .type = GPIO_ALTF_B,
+ },
+ {
+ .altfun = GPIO_ALT_I2C_3,
+ .start = 229,
+ .end = 230,
+ .cont = 0,
+ .type = GPIO_ALTF_C,
+ },
+ {
+ .altfun = GPIO_ALT_UART_0_MODEM,
+ .start = 0,
+ .end = 3,
+ .cont = 1,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_UART_0_MODEM,
+ .start = 33,
+ .end = 36,
+ .cont = 0,
+ .type = GPIO_ALTF_C,
+ },
+ {
+ .altfun = GPIO_ALT_UART_1,
+ .start = 4,
+ .end = 7,
+ .cont = 0,
+ .type =
+ GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_UART_2,
+ .start = 18,
+ .end = 19,
+ .cont = 1,
+ .type = GPIO_ALTF_B,
+ },
+ {
+ .altfun = GPIO_ALT_UART_2,
+ .start = 29,
+ .end = 32,
+ .cont = 0,
+ .type = GPIO_ALTF_C,
+ },
+ {
+ .altfun = GPIO_ALT_MSP_0,
+ .start = 12,
+ .end = 17,
+ .cont = 1,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_MSP_0,
+ .start = 21,
+ .end = 21,
+ .cont = 0,
+ .type = GPIO_ALTF_B,
+ },
+ {
+ .altfun = GPIO_ALT_MSP_1,
+ .start = 33,
+ .end = 36,
+ .cont = 0,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_MSP_2,
+ .start = 192,
+ .end = 196,
+ .cont = 0,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_LCD_PANEL,
+ .start = 64,
+ .end = 93,
+ .cont = 1,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_LCD_PANEL,
+ .start = 150,
+ .end = 171,
+ .cont = 0,
+ .type = GPIO_ALTF_B,
+ },
+ {
+ .altfun = GPIO_ALT_SD_CARD0,
+ .start = 18,
+ .end = 28,
+ .cont = 0,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_MM_CARD0,
+ .start = 18,
+ .end = 32,
+ .cont = 0,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_USB_OTG,
+ .start = 256,
+ .end = 267,
+ .cont = 0,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_EMMC,
+ .start = 197,
+ .end = 207,
+ .cont = 0,
+ .type = GPIO_ALTF_A,
+ },
+ {
+ .altfun = GPIO_ALT_POP_EMMC,
+ .start = 128,
+ .end = 138,
+ .cont = 0,
+ .type = GPIO_ALTF_A,
+ },
+};
+
+/*
+ * Static Function declarations
+ */
+enum gpio_error gpio_setpinconfig(int pin_id, struct gpio_config *config)
+{
+ struct gpio_register *p_gpio_register =
+ addr_gpio_register[GPIO_BLOCK(pin_id)];
+ u32 mask = 1UL << (pin_id % GPIO_PINS_PER_BLOCK);
+ enum gpio_error error = GPIO_OK;
+ u32 temp_reg;
+
+ switch (config->mode) {
+ case GPIO_ALTF_A:
+ temp_reg = readl(&p_gpio_register->gpio_afsa);
+ temp_reg |= mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsa);
+ temp_reg = readl(&p_gpio_register->gpio_afsb);
+ temp_reg &= ~mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsb);
+ break;
+ case GPIO_ALTF_B:
+ temp_reg = readl(&p_gpio_register->gpio_afsa);
+ temp_reg &= ~mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsa);
+ temp_reg = readl(&p_gpio_register->gpio_afsb);
+ temp_reg |= mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsb);
+ break;
+ case GPIO_ALTF_C:
+ temp_reg = readl(&p_gpio_register->gpio_afsa);
+ temp_reg |= mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsa);
+ temp_reg = readl(&p_gpio_register->gpio_afsb);
+ temp_reg |= mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsb);
+ break;
+ case GPIO_MODE_SOFTWARE:
+ temp_reg = readl(&p_gpio_register->gpio_afsa);
+ temp_reg &= ~mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsa);
+ temp_reg = readl(&p_gpio_register->gpio_afsb);
+ temp_reg &= ~mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsb);
+
+ switch (config->direction) {
+ case GPIO_DIR_INPUT:
+ writel(mask, &p_gpio_register->gpio_dirc);
+ break;
+ case GPIO_DIR_OUTPUT:
+ writel(mask, &p_gpio_register->gpio_dirs);
+ break;
+ case GPIO_DIR_LEAVE_UNCHANGED:
+ break;
+ default:
+ return GPIO_INVALID_PARAMETER;
+ }
+
+ break;
+ case GPIO_MODE_LEAVE_UNCHANGED:
+ break;
+ default:
+ return GPIO_INVALID_PARAMETER;
+ }
+ return error;
+}
+
+enum gpio_error gpio_resetgpiopin(int pin_id, char *dev_name)
+{
+ struct gpio_register *p_gpio_register =
+ addr_gpio_register[GPIO_BLOCK(pin_id)];
+ u32 mask = 1UL << (pin_id % GPIO_PINS_PER_BLOCK);
+ enum gpio_error error = GPIO_OK;
+ u32 temp_reg;
+
+ temp_reg = readl(&p_gpio_register->gpio_afsa);
+ temp_reg &= ~mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsa);
+ temp_reg = readl(&p_gpio_register->gpio_afsb);
+ temp_reg &= ~mask;
+ writel(temp_reg, &p_gpio_register->gpio_afsb);
+ writel(mask, &p_gpio_register->gpio_dirc);
+
+ return error;
+}
+
+struct gpio_config altfun_pinconfig;
+enum gpio_error gpio_altfunction(enum gpio_alt_function alt_func,
+ int which_altfunc, char *dev_name)
+{
+ int i, j, start, end;
+ enum gpio_error error = -1;
+
+ for (i = 0; i < ARRAY_SIZE(altfun_table); i++) {
+ if (altfun_table[i].altfun != alt_func)
+ continue;
+
+ start = altfun_table[i].start;
+ end = altfun_table[i].end;
+ for (j = start; j <= end; j++) {
+ if (which_altfunc == GPIO_ALTF_FIND)
+ altfun_pinconfig.mode = altfun_table[i].type;
+ else
+ altfun_pinconfig.mode = which_altfunc;
+ altfun_pinconfig.direction = GPIO_DIR_OUTPUT;
+ altfun_pinconfig.dev_name = dev_name;
+
+ if (which_altfunc != GPIO_ALTF_DISABLE)
+ error = gpio_setpinconfig(j, &altfun_pinconfig);
+ else
+ error = gpio_resetgpiopin(j, dev_name);
+ if (!error)
+ continue;
+ printf("GPIO %d configuration failure (nmdk_error:%d)",
+ j, error);
+ error = GPIO_INVALID_PARAMETER;
+ return error;
+ }
+
+ if (!altfun_table[i].cont)
+ break;
+ }
+ return error;
+}
+
+int gpio_writepin(int pin_id, enum gpio_data value, char *dev_name)
+{
+ struct gpio_register *p_gpio_register =
+ addr_gpio_register[GPIO_BLOCK(pin_id)];
+ u32 mask = 1UL << (pin_id % GPIO_PINS_PER_BLOCK);
+
+ switch (value) {
+ case GPIO_DATA_HIGH:
+ writel(mask, &p_gpio_register->gpio_dats);
+ break;
+ case GPIO_DATA_LOW:
+ writel(mask, &p_gpio_register->gpio_datc);
+ break;
+ default:
+ printf("Invalid value passed in %s", __FUNCTION__);
+ return GPIO_INVALID_PARAMETER;
+ }
+ return GPIO_OK;
+}
+
+int gpio_readpin(int pin_id, enum gpio_data *rv)
+{
+ struct gpio_register *p_gpio_register =
+ addr_gpio_register[GPIO_BLOCK(pin_id)];
+ u32 mask = 1UL << (pin_id % GPIO_PINS_PER_BLOCK);
+
+ if ((readl(&p_gpio_register->gpio_dat) & mask) != 0)
+ *rv = GPIO_DATA_HIGH;
+ else
+ *rv = GPIO_DATA_LOW;
+ return GPIO_OK;
+}
+
+int gpio_altfuncenable(enum gpio_alt_function altfunc, char *dev_name)
+{
+ return (int)gpio_altfunction(altfunc, GPIO_ALTF_FIND, dev_name);
+}
+
+int gpio_altfuncdisable(enum gpio_alt_function altfunc, char *dev_name)
+{
+ return (int)gpio_altfunction(altfunc, GPIO_ALTF_DISABLE, dev_name);
+}
new file mode 100644
@@ -0,0 +1,52 @@
+/*
+ * Copyright (C) 2009 ST-Ericsson SA
+ *
+ * Copied from the Linux version:
+ * Author: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#ifndef __MACH_PRCMU_FW_V1_H
+#define __MACH_PRCMU_FW_V1_H
+
+#define AP_EXECUTE 2
+#define I2CREAD 1
+#define I2C_WR_OK 1
+#define I2C_RD_OK 2
+#define I2CWRITE 0
+
+#define _PRCMU_TCDM_BASE U8500_PRCMU_TCDM_BASE
+#define PRCM_XP70_CUR_PWR_STATE (_PRCMU_TCDM_BASE + 0xFFC) /* 4 BYTES */
+
+#define PRCM_REQ_MB5 (_PRCMU_TCDM_BASE + 0xE44) /* 4 bytes */
+#define PRCM_ACK_MB5 (_PRCMU_TCDM_BASE + 0xDF4) /* 4 bytes */
+
+/* Mailbox 5 Requests */
+#define PRCM_REQ_MB5_I2COPTYPE_REG (PRCM_REQ_MB5 + 0x0)
+#define PRCM_REQ_MB5_BIT_FIELDS (PRCM_REQ_MB5 + 0x1)
+#define PRCM_REQ_MB5_I2CSLAVE (PRCM_REQ_MB5 + 0x2)
+#define PRCM_REQ_MB5_I2CVAL (PRCM_REQ_MB5 + 0x3)
+
+/* Mailbox 5 ACKs */
+#define PRCM_ACK_MB5_STATUS (PRCM_ACK_MB5 + 0x1)
+#define PRCM_ACK_MB5_SLAVE (PRCM_ACK_MB5 + 0x2)
+#define PRCM_ACK_MB5_VAL (PRCM_ACK_MB5 + 0x3)
+
+#define LOW_POWER_WAKEUP 1
+#define EXE_WAKEUP 0
+
+#define REQ_MB5 5
+
+#endif /* __MACH_PRCMU_FW_V1_H */
new file mode 100644
@@ -0,0 +1,165 @@
+/*
+ * Copyright (C) 2009 ST-Ericsson SA
+ *
+ * Adapted from the Linux version:
+ * Author: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ */
+
+/*
+ * NOTE: This currently does not support the I2C workaround access method.
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/hardware.h>
+#include <asm/types.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+
+#include "prcmu-fw.h"
+
+/* CPU mailbox registers */
+#define PRCM_MBOX_CPU_VAL (U8500_PRCMU_BASE + 0x0fc)
+#define PRCM_MBOX_CPU_SET (U8500_PRCMU_BASE + 0x100)
+#define PRCM_MBOX_CPU_CLR (U8500_PRCMU_BASE + 0x104)
+
+static int prcmu_is_ready(void)
+{
+ int ready = readb(PRCM_XP70_CUR_PWR_STATE) == AP_EXECUTE;
+ if (!ready)
+ printf("PRCMU firmware not ready\n");
+ return ready;
+}
+
+static int _wait_for_req_complete(int num)
+{
+ int timeout = 1000;
+
+ /* checking any already on-going transaction */
+ while ((readl(PRCM_MBOX_CPU_VAL) & (1 << num)) && timeout--)
+ ;
+
+ timeout = 1000;
+
+ /* Set an interrupt to XP70 */
+ writel(1 << num, PRCM_MBOX_CPU_SET);
+
+ while ((readl(PRCM_MBOX_CPU_VAL) & (1 << num)) && timeout--)
+ ;
+
+ if (!timeout) {
+ printf("PRCMU operation timed out\n");
+ return -1;
+ }
+
+ return 0;
+}
+
+/**
+ * prcmu_i2c_read - PRCMU - 4500 communication using PRCMU I2C
+ * @reg: - db8500 register bank to be accessed
+ * @slave: - db8500 register to be accessed
+ * Returns: ACK_MB5 value containing the status
+ */
+int prcmu_i2c_read(u8 reg, u16 slave)
+{
+ uint8_t i2c_status;
+ uint8_t i2c_val;
+
+ if (!prcmu_is_ready())
+ return -1;
+
+ debug("\nprcmu_4500_i2c_read:bank=%x;reg=%x;\n",
+ reg, slave);
+
+ /* prepare the data for mailbox 5 */
+ writeb((reg << 1) | I2CREAD, PRCM_REQ_MB5_I2COPTYPE_REG);
+ writeb((1 << 3) | 0x0, PRCM_REQ_MB5_BIT_FIELDS);
+ writeb(slave, PRCM_REQ_MB5_I2CSLAVE);
+ writeb(0, PRCM_REQ_MB5_I2CVAL);
+
+ _wait_for_req_complete(REQ_MB5);
+
+ /* retrieve values */
+ debug("ack-mb5:transfer status = %x\n",
+ readb(PRCM_ACK_MB5_STATUS));
+ debug("ack-mb5:reg bank = %x\n", readb(PRCM_ACK_MB5) >> 1);
+ debug("ack-mb5:slave_add = %x\n",
+ readb(PRCM_ACK_MB5_SLAVE));
+ debug("ack-mb5:reg_val = %d\n", readb(PRCM_ACK_MB5_VAL));
+
+ i2c_status = readb(PRCM_ACK_MB5_STATUS);
+ i2c_val = readb(PRCM_ACK_MB5_VAL);
+
+ if (i2c_status == I2C_RD_OK)
+ return i2c_val;
+ else {
+
+ printf("prcmu_i2c_read:read return status= %d\n",
+ i2c_status);
+ return -1;
+ }
+
+}
+
+/**
+ * prcmu_i2c_write - PRCMU-db8500 communication using PRCMU I2C
+ * @reg: - db8500 register bank to be accessed
+ * @slave: - db800 register to be written to
+ * @reg_data: - the data to write
+ * Returns: ACK_MB5 value containing the status
+ */
+int prcmu_i2c_write(u8 reg, u16 slave, u8 reg_data)
+{
+ uint8_t i2c_status;
+
+ if (!prcmu_is_ready())
+ return -1;
+
+ debug("\nprcmu_4500_i2c_write:bank=%x;reg=%x;\n",
+ reg, slave);
+
+ /* prepare the data for mailbox 5 */
+ writeb((reg << 1) | I2CWRITE, PRCM_REQ_MB5_I2COPTYPE_REG);
+ writeb((1 << 3) | 0x0, PRCM_REQ_MB5_BIT_FIELDS);
+ writeb(slave, PRCM_REQ_MB5_I2CSLAVE);
+ writeb(reg_data, PRCM_REQ_MB5_I2CVAL);
+
+ debug("\ncpu_is_u8500v11\n");
+ _wait_for_req_complete(REQ_MB5);
+
+ /* retrieve values */
+ debug("ack-mb5:transfer status = %x\n",
+ readb(PRCM_ACK_MB5_STATUS));
+ debug("ack-mb5:reg bank = %x\n", readb(PRCM_ACK_MB5) >> 1);
+ debug("ack-mb5:slave_add = %x\n",
+ readb(PRCM_ACK_MB5_SLAVE));
+ debug("ack-mb5:reg_val = %d\n", readb(PRCM_ACK_MB5_VAL));
+
+ i2c_status = readb(PRCM_ACK_MB5_STATUS);
+ debug("\ni2c_status = %x\n", i2c_status);
+ if (i2c_status == I2C_WR_OK)
+ return 0;
+ else {
+ printf("ape-i2c: i2c_status : 0x%x\n", i2c_status);
+ return -1;
+ }
+}
new file mode 100644
@@ -0,0 +1,546 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2009
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <config.h>
+#include <common.h>
+#include <i2c.h>
+#include <asm/types.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
+
+#define NOMADIK_PER4_BASE (0x80150000)
+#define NOMADIK_BACKUPRAM0_BASE (NOMADIK_PER4_BASE + 0x00000)
+#define NOMADIK_BACKUPRAM1_BASE (NOMADIK_PER4_BASE + 0x01000)
+
+/* Power, Reset, Clock Management Unit */
+/*
+ * SVA: Smart Video Accelerator
+ * SIA: Smart Imaging Accelerator
+ * SGA: Smart Graphic accelerator
+ * B2R2: Graphic blitter
+ */
+#define PRCMU_BASE CFG_PRCMU_BASE /* 0x80157000 for U8500 */
+#define PRCM_ARMCLKFIX_MGT_REG (PRCMU_BASE + 0x000)
+#define PRCM_ACLK_MGT_REG (PRCMU_BASE + 0x004)
+#define PRCM_SVAMMDSPCLK_MGT_REG (PRCMU_BASE + 0x008)
+#define PRCM_SIAMMDSPCLK_MGT_REG (PRCMU_BASE + 0x00C)
+#define PRCM_SAAMMDSPCLK_MGT_REG (PRCMU_BASE + 0x010)
+#define PRCM_SGACLK_MGT_REG (PRCMU_BASE + 0x014)
+#define PRCM_UARTCLK_MGT_REG (PRCMU_BASE + 0x018)
+#define PRCM_MSPCLK_MGT_REG (PRCMU_BASE + 0x01C)
+#define PRCM_I2CCLK_MGT_REG (PRCMU_BASE + 0x020)
+#define PRCM_SDMMCCLK_MGT_REG (PRCMU_BASE + 0x024)
+#define PRCM_SLIMCLK_MGT_REG (PRCMU_BASE + 0x028)
+#define PRCM_PER1CLK_MGT_REG (PRCMU_BASE + 0x02C)
+#define PRCM_PER2CLK_MGT_REG (PRCMU_BASE + 0x030)
+#define PRCM_PER3CLK_MGT_REG (PRCMU_BASE + 0x034)
+#define PRCM_PER5CLK_MGT_REG (PRCMU_BASE + 0x038)
+#define PRCM_PER6CLK_MGT_REG (PRCMU_BASE + 0x03C)
+#define PRCM_PER7CLK_MGT_REG (PRCMU_BASE + 0x040)
+#define PRCM_DMACLK_MGT_REG (PRCMU_BASE + 0x074)
+#define PRCM_B2R2CLK_MGT_REG (PRCMU_BASE + 0x078)
+
+#define PRCM_PLLSOC0_FREQ_REG (PRCMU_BASE + 0x080)
+#define PRCM_PLLSOC1_FREQ_REG (PRCMU_BASE + 0x084)
+#define PRCM_PLLARM_FREQ_REG (PRCMU_BASE + 0x088)
+#define PRCM_PLLDDR_FREQ_REG (PRCMU_BASE + 0x08C)
+#define PRCM_ARM_CHGCLKREQ_REG (PRCMU_BASE + 0x114)
+
+#define PRCM_TCR (PRCMU_BASE + 0x1C8)
+
+/*
+ * Memory controller register
+ */
+#define DMC_BASE_ADDR 0x80156000
+#define DMC_CTL_97 (DMC_BASE_ADDR + 0x184)
+
+int board_id; /* set in board_late_init() */
+
+/* PLLs for clock management registers */
+enum {
+ GATED = 0,
+ PLLSOC0, /* pllsw = 001, ffs() = 1 */
+ PLLSOC1, /* pllsw = 010, ffs() = 2 */
+ PLLDDR, /* pllsw = 100, ffs() = 3 */
+ PLLARM,
+};
+
+static struct pll_freq_regs {
+ int idx; /* index fror pll_name and pll_khz arrays */
+ uint32_t addr;
+} pll_freq_regs[] = {
+ {PLLSOC0, PRCM_PLLSOC0_FREQ_REG},
+ {PLLSOC1, PRCM_PLLSOC1_FREQ_REG},
+ {PLLDDR, PRCM_PLLDDR_FREQ_REG},
+ {PLLARM, PRCM_PLLARM_FREQ_REG},
+ {0, 0},
+};
+
+static const char *pll_name[5] = {"GATED", "SOC0", "SOC1", "DDR", "ARM"};
+static uint32_t pll_khz[5]; /* use ffs(pllsw(reg)) as index for 0..3 */
+
+static struct clk_mgt_regs {
+ uint32_t addr;
+ uint32_t val;
+ const char *descr;
+} clk_mgt_regs[] = {
+ /* register content taken from bootrom settings */
+ {PRCM_ARMCLKFIX_MGT_REG, 0x0120, "ARMCLKFIX"}, /* ena, SOC0/0, ??? */
+ {PRCM_ACLK_MGT_REG, 0x0125, "ACLK"}, /* ena, SOC0/5, 160 MHz */
+ {PRCM_SVAMMDSPCLK_MGT_REG, 0x1122, "SVA"}, /* ena, SOC0/2, 400 MHz */
+ {PRCM_SIAMMDSPCLK_MGT_REG, 0x0022, "SIA"}, /* dis, SOC0/2, 400 MHz */
+ {PRCM_SAAMMDSPCLK_MGT_REG, 0x0822, "SAA"}, /* dis, SOC0/4, 200 MHz */
+ {PRCM_SGACLK_MGT_REG, 0x0024, "SGA"}, /* dis, SOC0/4, 200 MHz */
+ {PRCM_UARTCLK_MGT_REG, 0x0300, "UART"}, /* ena, GATED, CLK38 */
+ {PRCM_MSPCLK_MGT_REG, 0x0200, "MSP"}, /* dis, GATED, CLK38 */
+ {PRCM_I2CCLK_MGT_REG, 0x0130, "I2C"}, /* ena, SOC0/16, 50 MHz */
+ {PRCM_SDMMCCLK_MGT_REG, 0x0130, "SDMMC"}, /* ena, SOC0/16, 50 MHz */
+ {PRCM_PER1CLK_MGT_REG, 0x126, "PER1"}, /* ena, SOC0/6, 133 MHz */
+ {PRCM_PER2CLK_MGT_REG, 0x126, "PER2"}, /* ena, SOC0/6, 133 MHz */
+ {PRCM_PER3CLK_MGT_REG, 0x126, "PER3"}, /* ena, SOC0/6, 133 MHz */
+ {PRCM_PER5CLK_MGT_REG, 0x126, "PER5"}, /* ena, SOC0/6, 133 MHz */
+ {PRCM_PER6CLK_MGT_REG, 0x126, "PER6"}, /* ena, SOC0/6, 133 MHz */
+ {PRCM_PER7CLK_MGT_REG, 0x128, "PER7"}, /* ena, SOC0/8, 100 MHz */
+ {PRCM_DMACLK_MGT_REG, 0x125, "DMA"}, /* ena, SOC0/5, 160 MHz */
+ {PRCM_B2R2CLK_MGT_REG, 0x025, "B2R2"}, /* dis, SOC0/5, 160 MHz */
+ {0, 0, NULL},
+};
+
+static void init_regs(void);
+
+DECLARE_GLOBAL_DATA_PTR;
+#if defined(CONFIG_SHOW_BOOT_PROGRESS)
+void show_boot_progress(int progress)
+{
+ printf("Boot reached stage %d\n", progress);
+}
+#endif
+
+static unsigned int read_asicid(void)
+{
+ unsigned int *address = (void *)U8500_BOOTROM_BASE
+ + U8500_BOOTROM_ASIC_ID_OFFSET;
+ return readl(address);
+}
+
+int cpu_is_u8500v11(void)
+{
+ return read_asicid() == 0x008500A1;
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_early_init_f(void)
+{
+ init_regs();
+ return 0;
+}
+
+int board_init(void)
+{
+ uint32_t unused_cols_rows;
+ unsigned int nrows;
+ unsigned int ncols;
+
+ gd->bd->bi_arch_number = 0x1A4;
+ gd->bd->bi_boot_params = 0x00000100;
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+
+ /*
+ * Assumption: 2 CS active, both CS have same layout.
+ * 15 rows max, 11 cols max (controller spec).
+ * memory chip has 8 banks, I/O width 32 bit.
+ * The correct way would be to read MR#8: I/O width and density,
+ * but this requires locking against the PRCMU firmware.
+ * Simplified approach:
+ * Read number of unused rows and columns from mem controller.
+ * size = nCS x 2^(rows+cols) x nbanks x buswidth_bytes
+ */
+ unused_cols_rows = readl(DMC_CTL_97);
+ nrows = 15 - (unused_cols_rows & 0x07);
+ ncols = 11 - ((unused_cols_rows & 0x0700) >> 8);
+ gd->bd->bi_dram[0].size = 2 * (1 << (nrows + ncols)) * 8 * 4;
+
+ icache_enable();
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = PHYS_SDRAM_SIZE_1;
+
+ return 0;
+}
+
+unsigned int addr_vall_arr[] = {
+ 0x8011F000, 0x0000FFFF, /* Clocks for HSI TODO: Enable reqd only */
+ 0x8011F008, 0x00001CFF, /* Clocks for HSI TODO: Enable reqd only */
+ 0x8000F000, 0x00007FFF, /* Clocks for I2C TODO: Enable reqd only */
+ 0x8000F008, 0x00007FFF, /* Clocks for I2C TODO: Enable reqd only */
+ 0x80157020, 0x00000150, /* I2C 48MHz clock */
+ 0x8012F000, 0x00007FFF, /* Clocks for SD TODO: Enable reqd only */
+ 0x8012F008, 0x00007FFF, /* Clocks for SD TODO: Enable reqd only */
+ 0xA03DF000, 0x0000000D, /* Clock for MTU Timers */
+ 0x8011E00C, 0x00000000, /* GPIO ALT FUNC for EMMC */
+ 0x8011E004, 0x0000FFE0, /* GPIO ALT FUNC for EMMC */
+ 0x8011E020, 0x0000FFE0, /* GPIO ALT FUNC for EMMC */
+ 0x8011E024, 0x00000000, /* GPIO ALT FUNC for EMMC */
+ 0x8012E000, 0x20000000, /* GPIO ALT FUNC for UART */
+ 0x8012E00C, 0x00000000, /* GPIO ALT FUNC for SD */
+ 0x8012E004, 0x0FFC0000, /* GPIO ALT FUNC for SD */
+ 0x8012E020, 0x60000000, /* GPIO ALT FUNC for SD */
+ 0x8012E024, 0x60000000, /* GPIO ALT FUNC for SD */
+ 0x801571E4, 0x0000000C, /* PRCMU settings for B2R2,
+ PRCM_APE_RESETN_SET_REG */
+ 0x80157024, 0x00000130, /* PRCMU settings for EMMC/SD */
+ 0xA03FF000, 0x00000003, /* USB */
+ 0xA03FF008, 0x00000001, /* USB */
+ 0xA03FE00C, 0x00000000, /* USB */
+ 0xA03FE020, 0x00000FFF, /* USB */
+ 0xA03FE024, 0x00000000 /* USB */
+};
+
+#ifdef BOARD_LATE_INIT
+#ifdef CONFIG_MMC
+
+#define LDO_VAUX3_MASK 0x3
+#define LDO_VAUX3_ENABLE 0x1
+#define VAUX3_VOLTAGE_2_9V 0xd
+
+#define AB8500_REGU_CTRL2 0x4
+#define AB8500_REGU_VRF1VAUX3_REGU_REG 0x040A
+#define AB8500_REGU_VRF1VAUX3_SEL_REG 0x0421
+
+extern int prcmu_i2c_read(u8 reg, u16 slave);
+extern int prcmu_i2c_write(u8 reg, u16 slave, u8 reg_data);
+
+static int hrefplus_mmc_power_init(void)
+{
+ int ret;
+ int val;
+
+ if (!cpu_is_u8500v11())
+ return 0;
+
+ /*
+ * On v1.1 HREF boards (HREF+), Vaux3 needs to be enabled for the SD
+ * card to work. This is done by enabling the regulators in the AB8500
+ * via PRCMU I2C transactions.
+ *
+ * This code is derived from the handling of AB8500_LDO_VAUX3 in
+ * ab8500_ldo_enable() and ab8500_ldo_disable() in Linux.
+ *
+ * Turn off and delay is required to have it work across soft reboots.
+ */
+
+ ret = prcmu_i2c_read(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG);
+ if (ret < 0)
+ goto out;
+
+ val = ret;
+
+ /* Turn off */
+ ret = prcmu_i2c_write(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG,
+ val & ~LDO_VAUX3_MASK);
+ if (ret < 0)
+ goto out;
+
+ udelay(10 * 1000);
+
+ /* Set the voltage to 2.9V */
+ ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
+ AB8500_REGU_VRF1VAUX3_SEL_REG,
+ VAUX3_VOLTAGE_2_9V);
+ if (ret < 0)
+ goto out;
+
+ val = val & ~LDO_VAUX3_MASK;
+ val = val | LDO_VAUX3_ENABLE;
+
+ /* Turn on the supply */
+ ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
+ AB8500_REGU_VRF1VAUX3_REGU_REG, val);
+
+out:
+ return ret;
+}
+#endif
+/*
+ * called after all initialisation were done, but before the generic
+ * mmc_initialize().
+ */
+int board_late_init(void)
+{
+ uchar byte;
+
+ /*
+ * Determine and set board_id environment variable
+ * 0: mop500, 1: href500
+ * Above boards have different GPIO expander chips which we can
+ * distinguish by the chip id.
+ *
+ * The board_id environment variable is needed for the Linux bootargs.
+ */
+ (void) i2c_set_bus_num(0);
+ (void) i2c_read(CONFIG_SYS_I2C_GPIOE_ADDR, 0x80, 1, &byte, 1);
+ if (byte == 0x01) {
+ board_id = 0;
+ setenv("board_id", "0");
+ } else {
+ board_id = 1;
+ setenv("board_id", "1");
+ }
+#ifdef CONFIG_MMC
+ hrefplus_mmc_power_init();
+
+ /*
+ * config extended GPIO pins for level shifter and
+ * SDMMC_ENABLE
+ */
+ if (board_id == 0) {
+ /* MOP500 */
+ byte = 0x0c;
+ (void) i2c_write(CONFIG_SYS_I2C_GPIOE_ADDR, 0x89, 1, &byte, 1);
+ (void) i2c_write(CONFIG_SYS_I2C_GPIOE_ADDR, 0x83, 1, &byte, 1);
+ } else {
+ /* HREF */
+ /* set the direction of GPIO KPY9 and KPY10 */
+ byte = 0x06;
+ (void) i2c_write(CONFIG_SYS_I2C_GPIOE_ADDR, 0xC8, 1, &byte, 1);
+ /* must be a multibyte access */
+ (void) i2c_write(CONFIG_SYS_I2C_GPIOE_ADDR, 0xC4, 1,
+ (uchar []) {0x06, 0x06}, 2);
+ }
+#endif /* CONFIG_MMC */
+ /*
+ * Create a memargs variable which points uses either the memargs256 or
+ * memargs512 environment variable, depending on the memory size.
+ * memargs is used to build the bootargs, memargs256 and memargs512 are
+ * stored in the environment.
+ */
+ if (gd->bd->bi_dram[0].size == 0x10000000) {
+ setenv("memargs", "setenv bootargs ${bootargs} ${memargs256}");
+ setenv("mem", "256M");
+ } else {
+ setenv("memargs", "setenv bootargs ${bootargs} ${memargs512}");
+ setenv("mem", "512M");
+ }
+
+ return 0;
+}
+#endif /* BOARD_LATE_INIT */
+
+static void early_gpio_setup(struct gpio_register *gpio_reg, u32 bits)
+{
+ writel(readl(&gpio_reg->gpio_dats) | bits, &gpio_reg->gpio_dats);
+ writel(readl(&gpio_reg->gpio_pdis) & ~bits, &gpio_reg->gpio_pdis);
+}
+
+static void init_regs(void)
+{
+ /* FIXME Remove magic register array settings for ED also */
+ struct prcmu *prcmu = (struct prcmu *) U8500_PRCMU_BASE;
+
+ /* Enable timers */
+ writel(1 << 17, &prcmu->tcr);
+
+ u8500_prcmu_enable(&prcmu->per1clk_mgt);
+ u8500_prcmu_enable(&prcmu->per2clk_mgt);
+ u8500_prcmu_enable(&prcmu->per3clk_mgt);
+ u8500_prcmu_enable(&prcmu->per5clk_mgt);
+ u8500_prcmu_enable(&prcmu->per6clk_mgt);
+ u8500_prcmu_enable(&prcmu->per7clk_mgt);
+
+ u8500_prcmu_enable(&prcmu->uartclk_mgt);
+ u8500_prcmu_enable(&prcmu->i2cclk_mgt);
+
+ u8500_prcmu_enable(&prcmu->sdmmcclk_mgt);
+
+ u8500_clock_enable(1, 9, -1); /* GPIO0 */
+
+ u8500_clock_enable(2, 11, -1); /* GPIO1 */
+
+ u8500_clock_enable(3, 8, -1); /* GPIO2 */
+ u8500_clock_enable(5, 1, -1); /* GPIO3 */
+
+ u8500_clock_enable(3, 6, 6); /* UART2 */
+
+ gpio_altfuncenable(GPIO_ALT_I2C_0, "I2C0");
+ u8500_clock_enable(3, 3, 3); /* I2C0 */
+
+ early_gpio_setup((struct gpio_register *)U8500_GPIO_0_BASE, 0x60000000);
+ gpio_altfuncenable(GPIO_ALT_UART_2, "UART2");
+
+ early_gpio_setup((struct gpio_register *)U8500_GPIO_6_BASE, 0x0000ffe0);
+ gpio_altfuncenable(GPIO_ALT_EMMC, "EMMC");
+
+ early_gpio_setup((struct gpio_register *)U8500_GPIO_0_BASE, 0x0000ffe0);
+ gpio_altfuncenable(GPIO_ALT_SD_CARD0, "SDCARD");
+
+ u8500_clock_enable(1, 5, 5); /* SDI0 */
+ u8500_clock_enable(2, 4, 2); /* SDI4 */
+
+ u8500_clock_enable(6, 7, -1); /* MTU0 */
+ u8500_clock_enable(3, 4, 4); /* SDI2 */
+
+ early_gpio_setup((struct gpio_register *)U8500_GPIO_4_BASE, 0x000007ff);
+ gpio_altfuncenable(GPIO_ALT_POP_EMMC, "EMMC");
+
+ /*
+ * Enabling clocks for all devices which are AMBA devices in the
+ * kernel. Otherwise they will not get probe()'d because the
+ * peripheral ID register will not be powered.
+ */
+
+ /* XXX: some of these differ between ED/V1 */
+
+ u8500_clock_enable(1, 1, 1); /* UART1 */
+ u8500_clock_enable(1, 0, 0); /* UART0 */
+
+ u8500_clock_enable(3, 2, 2); /* SSP1 */
+ u8500_clock_enable(3, 1, 1); /* SSP0 */
+
+ u8500_clock_enable(2, 8, -1); /* SPI0 */
+ u8500_clock_enable(2, 5, 3); /* MSP2 */
+}
+
+#ifdef CONFIG_MMC
+static int u8500_mmci_board_init(void)
+{
+ enum gpio_error error;
+ struct gpio_register *gpio_base_address;
+
+ gpio_base_address = (void *)(U8500_GPIO_0_BASE);
+ gpio_base_address->gpio_dats |= 0xFFC0000;
+ gpio_base_address->gpio_pdis &= ~0xFFC0000;
+
+ /* save the GPIO0 AFSELA register */
+ error = gpio_altfuncenable(GPIO_ALT_SD_CARD0, "MMC");
+ if (error != GPIO_OK) {
+ printf("u8500_mmci_board_init() gpio_altfuncenable failed\n");
+ return -ENODEV;
+ }
+ return 0;
+}
+
+int board_mmc_init(bd_t *bd)
+{
+ if (u8500_mmci_board_init())
+ return -ENODEV;
+
+ arm_pl180_mmci_init();
+ return 0;
+}
+#endif
+
+
+/*
+ * get_pll_freq_khz - return PLL frequency in kHz
+ */
+static uint32_t get_pll_freq_khz(uint32_t inclk_khz, uint32_t freq_reg)
+{
+ uint32_t idf, ldf, odf, seldiv, phi;
+
+ /*
+ * PLLOUTCLK = PHI = (INCLK*LDF)/(2*ODF*IDF) if SELDIV2=0
+ * PLLOUTCLK = PHI = (INCLK*LDF)/(4*ODF*IDF) if SELDIV2=1
+ * where:
+ * IDF=R(2:0) (when R=000, IDF=1d)
+ * LDF = 2*D(7:0) (D must be greater than or equal to 6)
+ * ODF = N(5:0) (when N=000000, 0DF=1d)
+ */
+
+ idf = (freq_reg & 0x70000) >> 16;
+ ldf = (freq_reg & 0xff) * 2;
+ odf = (freq_reg & 0x3f00) >> 8;
+ seldiv = (freq_reg & 0x01000000) >> 24;
+ phi = (inclk_khz * ldf) / (2 * odf * idf);
+ if (seldiv)
+ phi = phi/2;
+
+ return phi;
+}
+
+int do_clkinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ uint32_t inclk_khz;
+ uint32_t reg, phi;
+ uint32_t clk_khz;
+ unsigned int clk_sel;
+ struct clk_mgt_regs *clks = clk_mgt_regs;
+ struct pll_freq_regs *plls = pll_freq_regs;
+
+ /*
+ * Go through list of PLLs.
+ * Initialise pll out frequency array (pll_khz) and print frequency.
+ */
+ inclk_khz = 38400; /* 38.4 MHz */
+ while (plls->addr) {
+ reg = readl(plls->addr);
+ phi = get_pll_freq_khz(inclk_khz, reg);
+ pll_khz[plls->idx] = phi;
+ printf("%s PLL out frequency: %d.%d Mhz\n",
+ pll_name[plls->idx], phi/1000, phi % 1000);
+ plls++;
+ }
+
+ /* check ARM clock source */
+ reg = readl(PRCM_ARM_CHGCLKREQ_REG);
+ printf("A9 running on ");
+ if (reg & 1)
+ printf("external clock");
+ else
+ printf("ARM PLL");
+ printf("\n");
+
+ /* go through list of clk_mgt_reg */
+ printf("\n%19s %9s %7s %9s enabled\n",
+ "name(addr)", "value", "PLL", "CLK[MHz]");
+ while (clks->addr) {
+ reg = readl(clks->addr);
+ /* convert bit position into array index */
+ clk_sel = ffs((reg >> 5) & 0x7); /* PLLSW[2:0] */
+ printf("%9s(%08x): %08x", clks->descr, clks->addr, reg);
+ printf(", %6s", pll_name[clk_sel]);
+ if (reg & 0x200)
+ clk_khz = 38400; /* CLK38 is set */
+ else if ((reg & 0x1f) == 0)
+ /* ARMCLKFIX_MGT is 0x120, e.g. div = 0 ! */
+ clk_khz = 0;
+ else
+ clk_khz = pll_khz[clk_sel] / (reg & 0x1f);
+ printf(", %4d.%03d", clk_khz / 1000, clk_khz % 1000);
+ printf(", %s\n", (reg & 0x100) ? "ena" : "dis");
+ clks++;
+ }
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ clkinfo, 1, 1, do_clkinfo,
+ "print clock info",
+ ""
+);
@@ -132,6 +132,7 @@ smdkc100 arm armv7 smdkc100 samsung
s5pc210_universal arm armv7 universal_c210 samsung s5pc2xx
harmony arm armv7 harmony nvidia tegra2
seaboard arm armv7 seaboard nvidia tegra2
+u8500_href arm armv7 u8500 st-ericsson u8500
actux1 arm ixp
actux2 arm ixp
actux3 arm ixp
new file mode 100644
@@ -0,0 +1,243 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2009
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_U8500 1
+#define CONFIG_L2_OFF 1
+
+#define CONFIG_SYS_MEMTEST_START 0x00000000
+#define CONFIG_SYS_MEMTEST_END 0x1FFFFFFF
+#define CONFIG_SYS_HZ 1000 /* must be 1000 */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1
+#define BOARD_LATE_INIT 1
+
+/*
+ * Size of malloc() pool
+ */
+#ifdef CONFIG_BOOT_SRAM
+#define CONFIG_ENV_SIZE (32*1024)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 64*1024)
+#else
+#define CONFIG_ENV_SIZE (128*1024)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024)
+#endif
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* for initial data */
+
+/*
+ * PL011 Configuration
+ */
+#define CONFIG_PL011_SERIAL
+
+/*
+ * U8500 UART registers base for 3 serial devices
+ */
+#define CFG_UART0_BASE 0x80120000
+#define CFG_UART1_BASE 0x80121000
+#define CFG_UART2_BASE 0x80007000
+#define CFG_SERIAL0 CFG_UART0_BASE
+#define CFG_SERIAL1 CFG_UART1_BASE
+#define CFG_SERIAL2 CFG_UART2_BASE
+#define CONFIG_PL011_CLOCK 38400000
+#define CONFIG_PL01x_PORTS { (void *)CFG_SERIAL0, (void *)CFG_SERIAL1, \
+ (void *)CFG_SERIAL2 }
+#define CONFIG_CONS_INDEX 2
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Devices and file systems
+ */
+#define CONFIG_MMC 1
+#define CONFIG_GENERIC_MMC 1
+#define CONFIG_DOS_PARTITION 1
+
+/*
+ * Commands
+ */
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EMMC
+#define CONFIG_CMD_SOURCE
+#define CONFIG_CMD_I2C
+
+#ifndef CONFIG_BOOTDELAY
+#define CONFIG_BOOTDELAY 1
+#endif
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND "run emmcboot"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "verify=n\0" \
+ "loadaddr=0x00100000\0" \
+ "console=ttyAMA2,115200n8\0" \
+ "memargs256=mem=96M@0 mem_modem=32M@96M mem=30M@128M " \
+ "pmem=22M@158M pmem_hwb=44M@180M mem_mali=32@224M\0" \
+ "memargs512=mem=96M@0 mem_modem=32M@96M mem=44M@128M " \
+ "pmem=22M@172M mem=30M@194M mem_mali=32M@224M " \
+ "pmem_hwb=54M@256M mem=202M@310M\0" \
+ "commonargs=setenv bootargs cachepolicy=writealloc noinitrd " \
+ "init=init " \
+ "board_id=${board_id} " \
+ "logo.${logo} " \
+ "startup_graphics=${startup_graphics}\0" \
+ "emmcargs=setenv bootargs ${bootargs} " \
+ "root=/dev/mmcblk0p2 " \
+ "rootdelay=1\0" \
+ "addcons=setenv bootargs ${bootargs} " \
+ "console=${console}\0" \
+ "emmcboot=echo Booting from eMMC ...; " \
+ "run commonargs emmcargs addcons memargs;" \
+ "mmc read 0 ${loadaddr} 0xA0000 0x4000;" \
+ "bootm ${loadaddr}\0" \
+ "flash=mmc init 1;fatload mmc 1 ${loadaddr} flash.scr;" \
+ "source ${loadaddr}\0" \
+ "loaduimage=mmc init 1;fatload mmc 1 ${loadaddr} uImage\0" \
+ "usbtty=cdc_acm\0" \
+ "stdout=serial,usbtty\0" \
+ "stdin=serial,usbtty\0" \
+ "stderr=serial,usbtty\0"
+
+/*
+ * Miscellaneous configurable options
+ */
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "U8500 $ " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */
+
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
+
+#define CONFIG_SYS_HUSH_PARSER 1
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_CMDLINE_EDITING
+
+#define CONFIG_SETUP_MEMORY_TAGS 2
+#define CONFIG_INITRD_TAG 1
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+
+/*
+ * I2C
+ */
+#define CONFIG_U8500_I2C 1
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 0 /* slave addr of controller */
+#define CONFIG_SYS_U8500_I2C0_BASE 0x80004000
+#define CONFIG_SYS_U8500_I2C1_BASE 0x80122000
+#define CONFIG_SYS_U8500_I2C2_BASE 0x80128000
+#define CONFIG_SYS_U8500_I2C3_BASE 0x80110000
+#define CONFIG_SYS_U8500_I2C_BUS_MAX 4
+
+#define CONFIG_SYS_I2C_GPIOE_ADDR 0x42 /* GPIO expander chip addr */
+#define CONFIG_TC35892_GPIO
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
+#endif
+
+/*
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM_1 0x00000000 /* DDR-SDRAM Bank #1 */
+#define PHYS_SDRAM_SIZE_1 0x20000000 /* 512 MB */
+
+/*
+ * additions for new relocation code
+ */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_SIZE 0x100000
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET
+
+/* landing address before relocation */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0x0
+#endif
+
+/*
+ * MMC related configs
+ * NB Only externa SD slot is currently supported
+ */
+#define MMC_BLOCK_SIZE 512
+#define CONFIG_ARM_PL180_MMCI
+#define CONFIG_ARM_PL180_MMCI_BASE 0x80126000 /* MMC base for 8500 */
+#define CONFIG_ARM_PL180_MMCI_CLOCK_FREQ 6250000
+#define CONFIG_MMC_DEV_NUM 1
+
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_SAVEENV /* CMD_ENV is obsolete but used in env_emmc.c */
+#define CONFIG_ENV_IS_IN_MMC 1
+#define CONFIG_ENV_OFFSET 0x13F80000
+#define CONFIG_SYS_MMC_ENV_DEV 0 /* SLOT2: eMMC */
+
+/*
+ * FLASH and environment organization
+ */
+#define CONFIG_SYS_NO_FLASH
+
+/*
+ * base register values for U8500
+ */
+#define CFG_PRCMU_BASE 0x80157000 /* Power, reset and clock
+ management unit */
+#define CFG_FSMC_BASE 0x80000000 /* FSMC Controller */
+
+#endif /* __CONFIG_H */
Based on ST-Ericsson private git repo. Plus changes to use arm_pl180_mmci driver. This board support requires the vexpress mmc driver patch set from Matt Waddel. Signed-off-by: John Rigby <john.rigby@linaro.org> CC: Albert Aribaud <albert.aribaud@free.fr> --- v2: cleanup, mostly removal of unused defines and include files board/st-ericsson/u8500/Makefile | 50 +++ board/st-ericsson/u8500/gpio.c | 347 +++++++++++++++++++++ board/st-ericsson/u8500/prcmu-fw.h | 52 ++++ board/st-ericsson/u8500/prcmu.c | 165 ++++++++++ board/st-ericsson/u8500/u8500_href.c | 546 ++++++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/u8500_href.h | 243 +++++++++++++++ 7 files changed, 1404 insertions(+), 0 deletions(-) create mode 100644 board/st-ericsson/u8500/Makefile create mode 100644 board/st-ericsson/u8500/gpio.c create mode 100644 board/st-ericsson/u8500/prcmu-fw.h create mode 100644 board/st-ericsson/u8500/prcmu.c create mode 100644 board/st-ericsson/u8500/u8500_href.c create mode 100644 include/configs/u8500_href.h